Scribd
Upload
160 views4 pages

Upgrading HST 3000 Broadcom Modem

This instruction is for updating the “MODEM” firmware (PHY) on a Broadcom Bonded SIM for the HST-3000. HST-3000s with firmware updated in the field must have this modem firmware upgraded in addition to the HST-3000 base unit firmware. Updating the HST-3000 base unit firmware is a separate procedure, which must be completed prior to updating the PHY.

Uploaded by

zoranpr
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
160 views4 pages

Upgrading HST 3000 Broadcom Modem

This instruction is for updating the “MODEM” firmware (PHY) on a Broadcom Bonded SIM for the HST-3000. HST-3000s with firmware updated in the field must have this modem firmware upgraded in addition to the HST-3000 base unit firmware. Updating the HST-3000 base unit firmware is a separate procedure, which must be completed prior to updating the PHY.

Uploaded by

zoranpr
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

Instructions for Upgrading the HST-3000

Modem PHY (Physical Layer Interface) Version


Purpose:
This instruction is for updating the MODEM firmware (PHY) on a Broadcom Bonded SIM for the
HST-3000. HST-3000s with firmware updated in the field must have this modem firmware upgraded in
addition to the HST-3000 base unit firmware. Updating the HST-3000 base unit firmware is a separate
procedure, which must be completed prior to updating the PHY.
There are three PHYs for the Broadcom Module:
1. MultiPHY (xDSL single pair ADSL or VDSL)
2. VDSL BOND
3. ADSL BOND
Upgrading the PHY:
1. To upgrade the PHY, first place the USB in the HST USB slot.
2. To upgrade any or all of the PHYs, launch any of the DSL applications (XDSL, VDSL BOND, or
ADSL BOND)

3. Press the HST-3000 softkey below the word Display and scroll with the arrow keys to 8
Identity or press the number 8 on the keypad dialer

1
JDSU Technical Assistance Center:
1-855-ASK-JDSU (1-855-275-5378) options 3-1-1 (toll free)

4. Press the softkey below the word Actions

5. Select item 1 Update Modem Software USB

6. The HST-3000 will check the USB stick for valid script files. An update for each script found on
the USB stick will appear in this dialog box. Note this HST-3000 does NOT verify the associated
Broadcom image is on the USB stick). With this dialog box you can select which images you
want to update. Use the OK key to toggle an image on or off. You can also use the Select All and
Clear All softkeys. Once you have selected the image(s) you want to update press the Accept
softkey. You may only see the ADSL Bonded selection.

2
JDSU Technical Assistance Center:
1-855-ASK-JDSU (1-855-275-5378) options 3-1-1 (toll free)

7. You will then see a dialog box informing you that the Update is in Progress with a progress bar at
the bottom.

8. After the update(s) are complete you will see a dialog box informing you that the update process
was completed.

9. If the update image is not on the USB stick, an Error dialog box will indicate that the modem
PHY cannot be found.

10. Other errors that may occur as well. If that happens you will see a dialog box with the Error Code.
For help, call the JDSU Technical Assistance Center at 1-855-ASK-JDSU (1-855-275-5378)
options 3-1-1 (toll free) or by email at [email protected].
3
JDSU Technical Assistance Center:
1-855-ASK-JDSU (1-855-275-5378) options 3-1-1 (toll free)

11. Upon completion the HST-3000 will have updated the PHY indicated by the DSL Version. The
actual DSL Version, as well Modem SW version shown on the HST-300 will vary according to
the actual firmware release.

4
JDSU Technical Assistance Center:
1-855-ASK-JDSU (1-855-275-5378) options 3-1-1 (toll free)

You might also like