Scribd
Upload
35 views

Configuring Devicenet Network

1. Configure the DeviceNet interface driver in RSNetWorx for DeviceNet by selecting the Allen-Bradley DH485 driver, choosing the correct COM port, and clicking OK. 2. In RSNetWorx, go online to browse the DeviceNet network, download the network configuration, and commission nodes by selecting the scanner module and assigning it a new node address of 5. 3. Place the scanner back in RUN mode to verify normal operation and check for any alarm codes or LED colors on the scanner that may indicate issues.

Uploaded by

vinhpo51290
Copyright
© © All Rights Reserved
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
35 views

Configuring Devicenet Network

1. Configure the DeviceNet interface driver in RSNetWorx for DeviceNet by selecting the Allen-Bradley DH485 driver, choosing the correct COM port, and clicking OK. 2. In RSNetWorx, go online to browse the DeviceNet network, download the network configuration, and commission nodes by selecting the scanner module and assigning it a new node address of 5. 3. Place the scanner back in RUN mode to verify normal operation and check for any alarm codes or LED colors on the scanner that may indicate issues.

Uploaded by

vinhpo51290
Copyright
© © All Rights Reserved
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 10

CONFIGURING DEVICENET NETWORK

Previous requirements for configuring device net network:


Hook up Allen Bradley Cable to the PC COM port and to the Device net
Interface !"D# port$
Device net Interface !"D# %hould be plugged into Device &et 'canner
'(C# through the ) pin green connector$
Device net Interface %hould be powered up$ Check the po%ition of the %witch
located on one %ide of the Interface %et up on the upper po%ition#$
"ollow the%e %tep% in order to get the device net network running:
'(C *u%t be in PROG Mode$
'tart +%(in,$ -he +%(in, *ain widow will open$
"ro* the Communications *enu. %elect Coni!ure Drivers a% %hown
above$ -he following window will appear thi% %creen %hoot *ay change
fro* your% depending on the driver% you had configured before in +%(in,#$
"to# a$$ the drivers %howed up on the Configured Drivers by %electing the*
and pre%%ing on 'top$
"ro* Available Driver Types pull down li%t %elect DeviceNet Drivers$
Click on Add New$ /ou will %ee the following choice%$
'elect the %$$en &rad$e' ())*+KFD,-he Driver Configuration window will
appear$ "e$ect t-e COM Port nu*ber your PC i% u%ing for co**unicating
and click OK$
-he %oftware will take a few %econd% to configure the driver$ 0hen it i% done
the following pro*pt will appear$
'elect the default nu*ber na*e ())*+KFD+( and click on OK$
Clo%e +%(in,$
You will use the driver you just configured to browse and configure the device
net network with RsNetWor for DeviceNet!
"ro* the CD I %ent you open +%&et0or, "ile 1$dnt .ms+/**0s$c0micro0(+
/+1+2+EMPT3+4+((+50modu$ar,dnt6
"ro* Net7or8 *enu %elect On 9ine and pre%% %cce#t$
+%&et0or, will %tart brow%ing the network$
Once you are connected in On$ine: fro* Net7or8 *enu %elect Do7n$oad
to Net7or8,
Pre%% OK and downloading will %tart$
Once downloading i% done and 'ou do not !et an' icon on any device net
network device% 'canner. D&I *odule and I2O *odule%# you can !o o$ine
and place the "9C in RUN Mode$
Once downloading i% done and 'ou !et an icon on t-e "canner device. go
%ee help or 3'y*bol (egend4$ Could be po%%ible that the "canner Node
does not matc- with the node addre%% been %etup on the la%t downloading$
-herefore. fro* Too$s *enu %elect Node Commissionin!,
Pre%% &ro7se on the window %howed up below$
"ro* the new window %elect ())*+KFD+( Device&et Driver -hi% window
*ay be different to your% depending on the driver% you had configured
before on the +%(in,#
0hen %electing 56678!"D85 Driver all device% connected on the network are
di%played on the right %ide of the window$ 'elect ()1)+"canner Modu$e and
pre%% OK$
On the new window appeared pre%% &ro7se$ After a few %econd% the field
for entering the new &ode Addre%% i% enabled$ -ype in the new &ode
Addre%% -he 'canner Module i% alway% %etup a% &ode Addre%% 7 or 5.
therefore type in 5 %ince the 1dnt file wa% configured a% 7 and that could be
the rea%on why they *i%*atch# and pre%% %##$'$
Download again the &etwork Configuration and 'ave Change%$
Di%connect fro* On(ine
Place the '(C in +9& Mode$
Veri' 7-et-er ater #$acin! "9C in Run Mode 'ou !et or not an' a$arm
code on t-e "canner Dis#$a' or an' o t-e 9eds .Modu$e and Net6 on t-e
"canner is $as-in! red or !reen,
C-ec8 t-e meanin! o t-e %$arm Code on t-e Trou;$es-ootin! .C-a#ter )
o t-e DeviceNet"canner,#d i$e6 on t-e CD,

You might also like