SECTION 1

1.


Which one of the following is incombustible ?
A. H2 B. CCl4
C. C2H2 D. S

2. The softness or hardness of a grinding wheel depends upon the type
& amount of bonding material used. For general purpose cutter
grinding __________ grinding wheel is normally used.
A. hard
B. soft
C. silicon carbide
D. aluminium oxide

3. Tin based white metals are used, where bearings are subjected to
A. high pressure & load.
B. low pressure & load.
C. high temperature.
D. large surface wear.

4. Friction factor for fluid flow in pipe does not depend upon the
A. pipe length.
B. pipe roughness.
C. fluid density & viscosity.
D. mass flow rate of fluid.

5. All of the following alloying elements of steel increases hardness but
sacrifice ductility, except
A. nickel B. vanadium
C. molybdenum D. chromium

6. The following type of bonding is strongly directional in solids.
A. Vander Waal's
B. Ionic
C. Metallic
D. Covalant

7. Fog is an example of colloidal system of
A. solid dispersed in gas.
B. solid dispersed in liquid.
C. liquid dispersed in gas.
D. gas dispersed in liquid.

8. Chromium molybdenum steel can not be welded using __________
welding.
A. thermit
B. electrical resistance
C. oxy-acetylene
D. any of these

9. Speisses is a mixture of the following:
A. Arsenides of heavy metals.
B. Antimonides of heavy metals.
C. Arsenides & antimonides of heavy metals.
D. Iron, cobalt and nickel.

10. Auto collimator is used to check
A. flatness
B. angle
C. rotor balancing
D. roughness

11. In troposphere (the weather domain), the temperature 't' at height 'h'
above the sea level in metres is given by (where, temperature at sea
level is 15C and t is in C.)
A. t = 15 - 0.0065 h
B. t = 15 + 0.0065 h
C. t = 0.0035 h - 15
D. t = 15 - 0.0035 h

12. A high pressure boiler generates steam at a pressure greater than
__________ kg/cm
2
.
A. 10 B. 30
C. 50 D. 80

13. Evaporative cooling process employs a combination of cooling and
humidification in which the
A. sensible heat is added.
B. sensible heat is removed and the latent heat is added.
C. latent heat is removed.
D. sensible heat is added and latent heat is removed.

14. Which of the following is not an explosive ?
A. TNT
B. CMC
C. RDX
D. Lead azide

15. Maxwell's thermodynamic relations applies to the
A. chemical systems in equilibrium.
B. mechanical systems in equilibrium.
C. irreversible thermodynamic processes.
D. reversible thermodynamic processes.

16. Annealing ofwhite cast iron produces __________ iron.
A. grey B. nodular
C. malleable D. spheroidal

17. Resistance of an electrical conductor is proportional to its (where, l =
length and A = cross-sectional area of the conductor)
A. A
B. l
C. A
2

D. both 'a' & 'b'

18. A solar cell converts the sunlight directly into __________ energy.
A. thermal B. electrical
C. mechanical D. chemical

19. If a nuclear reactor produces more fissile nuclear fuel than it
consumes, then it is called a __________ reactor.
A. critical B. breeder
C. fertile D. heterogenous

20. Wrought iron is never spaped by
A. casting
B. cold working
C. forging
D. welding

21. Powder metallurgy process does not make metal powder by
A. atomisation
B. grinding/milling
C. hammering
D. electrolytic deposition

22. In the blast furnace, incorporation of water vapour in the blast gives
the following effect.
A. Increases the reducing potential of the gas.
B. Increases the flame temperature.
C. No significant change occurs.
D. Increases the hydrogen content in the metal.

23. Pick out the wrong statement.
A.
A ferromagnetic material becomes paramagnetic above the 'Curie
temperature'.
B.
Permanent magnets are made of hard materials, whereas
electromagnets require soft magnetic materials.
C.
Soft magnetic materials (e.g., pure iron) have higher permeability
and low hysterisis loss and coercive forces.
D. Tungsten steel and alnico are not hard magnetic materials.

24. The usual energy consumption in electric arc furnace steel making
is __________ KWh/ton of steel.
A. 60 - 100
B. 400 - 700
C. 1200 -1500
D. 2000 - 2300

25. Maximum permissible air velocity in pipelines is about __________
metre/second.
A. 5 B. 10
C. 20 D. 40

26. Area under the stress-strain curve upto the __________ is referred to
as the modulus of resilience.
A. yield strength
B. elastic limit
C. proportional limit
D. maximum point

27. __________ is the hardest oxide and is hence used where high wear
resistance at high temperature is required.
A. Beryllia B. Zirconia
C. Alumina D. Magnesia

28. Titanium alloys are welded using the Following process:
A. TIG welding.
B. Submerged arc welding.
C. Butt welding.
D. Electron beam welding.

29. An alloy of Fe - 0.4 % C is
A. cast iron.
B. hypo-eutectoid steel.
C. hyper-eutectoid steel.
D. eutectoid steel

30. A material in which the atoms are arranged regularly in some
directions but not in others, is termed as 'mesomorphous material';
an example of which is
A. lead B. glass
C. mica D. silver

31. In extrusion of metals, which of the following statement is true ?
A. speed of the extruded material is same as that of ram speed.
B. Redundant work is a function of the die angle.
C.
Relative motion between the billet surface and the container wall
is always present.
D. Hollow ram is used for indirect extrusion.

32. Nuclear fission of one atom of uranium-235 produces the energy
equivalent to about __________ MeV.
A. 20 B. 200
C. 500 D. 1000

33. Which of the following parameters is not responsible for the heat
loss from a hot steam carrying bare pipe surface located in a room
without fans ?
A. Emissivity of pipe surface.
B. Diameter & length of the pipe.
C. Temperature of hot pipe surface & that of air in the room.
D. none of these.

34. Machinability of hard alloys and tool steels is improved by
A. spherodising B. annealing
C. tempering D. normalising

35. Transformation range for ferrous material is the temperature
interval during which __________ is formed during its heating.
A. cementite B. austenite
C. martensite D. pearlite

36. Maximum amount of thermal radiation is emitted at all wavelengths
at any specified temperature by a/an __________ body.
A. grey B. black
C. opaque D. white

37. In condensers used in thermal power plants, steam is normally used
in shell side and cooling water on the tube side, because of the
reason that
A.
compared to the mass flow rate of cooling water, the rate of
condensation of steam is invariably smaller.
B.
maintaining vacuum on tube side is more difficult than that on
the shell side.
C.
water velocity can be increased conveniently to increase the
overall heat transfer co-efficient because of its lower specific
volume compared to steam.
D. condenser can act as a storage unit for condensed steam.

38. Cobalt - 60 is used as a source of __________ in medical therapy &
industrial radiography.
A. X-rays B. -rays
C. -rays D. -rays

39. Absolute zero pressure can be attained at a temperature of
A. 0C
B. 0K
C. 0R
D. none of these

40. The product out from a cupola is called
A. wrought iron
B. pig iron
C. cast iron
D. none of these

41. Nusselt number is related to Grashoff number (Gr) in turbulent &
laminar flow respectively, in respect of free convection over a vertical
flat plate as
A. Gr
0.25
, Gr
B. Gr
0.25
, Gr
0.33

C. Gr, Gr
0.25

D. Gr
0.33
, Gr
0.25


42. If the demand for an item is trebled and the order cost is reduced to
one third, then the economic order quantity
A. is trebled.
B. remains unchanged.
C. decreases by a factor of 3.
D. decreases by a factor of 1/3.

43. Copper deposits are found in India at the following location:
A. Kudremukh B. Kolar
C. Khetri D. Ramagundam

44. Electrical conductivities of semi-conductors are of the order of
__________ ohm/cm.
A. 10
-3
B. 10
3

C. 10
-15
D. l0
15


45. Corrosion of metals can not be prevented by its
A. tempering B. chromising
C. aluminising D. alloying

46. Transition from laminar to turbulent zone in free convection heat
transfer is governed by the critical value of
A. Grashoff number.
B. Grashoff number & Reynolds number.
C. Reynolds number.
D. Grashoff number & Prandtl number.

47. The most economical channel section for the fluid flow is the one for
which the discharge is maximum for a given cross-sectional area.
Vertical velocity distribution in an open channel for laminar flow can
be assumed to be
A. parabolic
B. hyperbolic
C. straight line
D. none of these

48. Energy of the sun arises mainly from __________ reactions.
A. fusion
B. fission
C. combustion
D. none of these

49. Which of the following fastening devices has a head at one end and a
nut fitted to the other ?
A. Bolt
B. Stud
C. Top bolt
D. None of these

50. Sudden fall of atmospheric pressure by a large amount is an
indication of the
A. rain
B. cold wave
C. storm
D. fair weather



























SECTION 2
1. In chemical dehumidification process
A. wet bulb temperature increases.
B. dry bulb temperature remains constant.
C. dew point temperature increases.
D. dry bulb temperature increases.

2. Secondary hardening in steels arises out of the
A. precipitation of fine alloy carbides at high temperatures.
B. refinement of ferrite grain size by working.
C. decomposition of retained austenite upon heat treatment.
D. precipitation of complex inter-metal-lics upon heat treatment.

3. Drills are usually made of
A. cermets
B. high speed steel
C. alloy steel
D. tungsten carbide

4. Tumbling is the process of improving the __________ of the
materials/parts.
A. surface finish
B. fatigue limit
C. creep limit
D. surface cleanlineses

5. The __________ of a double acting reciprocating pump as compared to
the single acting pump will be almost double.
A. flow output
B. head developed
C. overall efficiency
D. weight

6. __________ of air does not increase with increase in temperature.
A. Density
B. Thermal diffusivity
C. Viscosity
D. Thermal conductivity

7. Spherical shape of mercury droplets is due to its
A. high viscosity.
B. low surface tension.
C. high density.
D. high surface tension.

8. Sub zero treatment of steel is done to
A. suppress martensite transformation.
B. enhance its working performance in sub zero atmosphere.
C. reduce the retained austenite in hardened steel.
D. induce temper brittleness after its hardening.

9. Air-petrol ratio for maximum power generation in spark ignition
engine is about
A. 6:1
B. 12 : 1
C. 18 : 1
D. 24 : 1

10. Which of the following varies as the square root of oil pressure
during atomisation of fuel oil through a pressure jet burner ?
A. Output & fineness
B. Velocity
C. Both (a) & (b)
D. None of these

11. The most suitable material of construction for a sewer to carry
sewage under high pressure is
A. asbestos cement
B. steel
C. cement concrete
D. stoneware

12. Filler material used in welding should have __________ as compared
to the parent metal to be welded.
A. lower melting temperature
B. same melting temperature
C. same composition
D. both 'b' & 'c'

13. Oxygen cylinders used for autogenous (cutting/welding) purposes
are
A. seamless & made of steel.
B. heat treated before use.
C. made by sand casting.
D. welded steel cylinders.

14. Identify the correct statement.
A. Sphlerite is zinc oxide.
B. The first law of the thermodynamics is stated as E = Q - W.
C. Lead can be produced in a blast furnace.
D.
T. ferrooxidans is a fungus that can be used for leaching
chalcopyrite.

15. Dowtherm is a
A. high temperature heating medium (a petroleum product).
B. product of coal tar distillation.
C. very heat sensitive material.
D. none of these.

16. To counteract the bad effects of strain hardening on a cold formed
part, it must be
A. tempered B. normalised
C. annealed D. hardened

17. The dew point temperature lines on psychrometric charts are
straight inclined sloping downwards to the right. When relative
humidity of moist air is 100%, then
A. wet bulb temperature=dry bulb temperature.
B. wet bulb temperature=dew point temperature.
C. saturation temperature=dew point temperature.
D. all 'a' , 'b' & 'c'

18. Galvanic corrosion can not be prevented by
A. cathodic protection.
B. anodic protection.
C. usage of largest possible anodic area.
D. any one of these.

19. Fire in fuel gas pipelines is extinguished most effectively by
A. spraying water.
B. blanketting the area with nitrogen atmosphere.
C. fire fighting foam.
D. none of these.

20. Which of the following is the most suitable abrasive for grinding high
tensile strength materials ?
A. Silicon carbide
B. Corundum
C. Aluminium oxide
D. Boron carbide

21. Case hardening is not done by
A. nitriding
B. hot dipping
C. electroplating
D. both b & c

22. Satellites burn off during re-entry to earth's atmosphere, because of
the
A. combustion with air.
B. gravitational pull by earth.
C. friction with earth's atmosphere.
D. loss in weight of the satellite.

23. With increase in compression ratio, the volumetric efficiency of air
compressor
A. increases.
B. decreases.
C. remains same.
D. may increase or decrease (depends on the suction pressure).

24. Neutrons are present in all atoms except that of
A. He B. C
C. H D. Ar

25. Biological shield in a nuclear reactor is generally provided to protect
against the
A. -rays
B. -rays
C. gamma rays & neutrons
D. electrons

26. __________ circuit is most commonly used to measure strain with the
help of a strain gauge.
A. Ballast
B. Voltage balancing potentiometric
C. Simple current sensitive
D. none of these

27. Which of the following is normally not found in both the S.I. (petrol)
& C.I. (diesel) engines ?
A. Air filter
B. Fuel injector
C. Exhaust silencer
D. Battery

28. __________ is a special constituent of chlorophyll without which
photosynthesis is not possible.
A. Calcium B. Nitrogen
C. Phosphorous D. Hydrogen

29. __________ is used as a material of construction for the blade of
power saw.
A. Wrought iron
B. Stainless steel
C. Mild steel
D. High speed steel

30. During decarburising of a plain carbon steel, the thickness of ferrite
layer growth is proportional to
A. time
B. square root of time
C. square of time
D. cube of time

31. Laser welding is widely employed in the __________ industries.
A. electronic B. structural
C. process D. heavy

32. Dryness factor of steam is defined as the ratio of the mass of vapor
in the mixture to the mass of the mixture. Dryness factor of steam is
measured by a __________ calorimeter.
A. bomb B. throttling
C. Junker's D. Boy's

33. Which of the following is used to produce draught in the locomotive
boilers ?
A. Chimney.
B. Induced draught fan.
C. Forced draught fan.
D. Steam jet arrangement.

34. Temper brittleness of a material can be fairly detected by the
__________ test.
A. fatigue
B. notched bar impact
C. tensile
D. hardness

35. When the wavelength of incident X-rays increases, the angle of
diffraction
A. decreases.
B. increases.
C. remains constant.
D. shows no systematic variation.

36. The elastic strain energy of a unit length of an edge dislocation as
compared to that of a screw dislocation is
A. more B. equal
C. less D. double

37. The specific gravity of coal depends mainly on its __________ content.
A. carbon
B. volatile matter
C. ash
D. moisture

38. In case of condensers & evaporators operating under given terminal
conditions, LMTD (logarithmic mean temperature difference) for
counter flow as compared to that for parallel flow is
A. more
B. less
C. equal
D. much more

39. Normalising does not __________ of a metal.
A. improve machinability & tensile strength
B. remove internal stresses
C. refine the structure
D. remove strains caused by cold working

40. Which of the following hardness tests does not measure the
indentation hardness of metals and alloys ?
A. Vicker's hardness test.
B. Shore sceleroscope test.
C. Brinell hardness test.
D. Rockwell hardness test.

41. With increase in annealing temperature, the following defect density
decreases.
A. Vacancy
B. Dislocation
C. Grain boundary
D. All of them

42. Carnot cycle is also termed as the constant __________ cycle in
thermodynamics.
A. entropy B. pressure
C. volume D. heat

43. Thermistors are used in __________ devices.
A. voltage measuring
B. temperature measuring
C. temperature compensating
D. both (b) & (c)

44. Broaching tools are usually made of
A. cermets
B. high speed steel
C. tungsten carbide
D. stellite

45. The ratio of the shear stress to the principal stress on a principal
plane is
A. 0 B. 1
C. 1/2 D. 1/3

46. Minimum safe distance between two liquid fuel storage tanks is
equal to (where, H = height of the tank)
A. H B. H/2
C. H/4 D. H/6

47. Propulsion of rocket follows from the
A. Newton's second law of motion.
B. Newton's third law of motion.
C. law of projectiles.
D. Archimedes principle.

48. In multipass welds, shot peening is done after each pass to
A. close the surface porosity.
B. break the continuity of columnar grains.
C. flatten the weldment.
D. introduce texture in the weld.

49. Pick out the correct statement.
A. Materials exhibiting high elasticity obey Hooke's law.
B.
The elastic behaviour of rubber under compression is the same as
its behaviour under tension.
C.
The damping capacity of a material is due to its plastic
deformation.
D.
The stress required to cause plastic flow in polycrystalline
material is higher as compared to monocrystalline materials due
to the presence of grains of different orientations.

50. Consider the equilibrium A(g) + B(g) = AB(g). When the partial pressure
of A is 10
-2
atm, the partial pressure of B is 10
-3
atm and the partial
pressure of AB is 1 atm, the equilibrium constant 'K' is
A. 10 atm
-1

B. 10
5
atm
-1

C. 10 (dimensionless)
D. 10
5
(dimensionless)















SECTION 3
1. In the formation of cermets, the ratio of ceramic material to metallic
material is usually 80:20. Which of the following is a cermet ?
A. Zirconia
B. Alumina
C. Bakelite
D. Tungsten carbide

2. Enzymes belong to the category of
A. proteins B. carbohydrates
C. vitamins D. fats

3. What is the value of included angle of a triangular notch for
maximum discharge ?
A. 30 B. 60
C. 90 D. 120

4. For separating small pieces of metal from engine oil of a car, the best
separating technique is the
A. chromatography
B. evaporation
C. filtration
D. fractional distillation

5. Heat flow across a hollow sphere of inner radius 'r1' and outer radius
'r2' is directly proportional to
A.

B.

C.

D.


6. On oscilloscope screen for dynamic measurement, lissajous diagram
is normally used to determine the __________ of the input signal.
A. frequency
B. amplitude
C. damping
D. none of these

7. Fire refining process is employed in case of
A. tin B. copper
C. zinc D. aluminium

8. Larger length & diameter water pipes are made by
A. electrical resistance welding.
B. die casting.
C. semi-centrifugal casting.
D. continuous casting.

9. Carbide tipped cutting tools are manufactured by powder metallurgy
techniques and have a composition of
A. 90% tungsten carbide and 10% cobalt.
B. 70% aluminium oxide & 30% silica.
C. 30% nickel, 15% chromium & 55% tungsten.
D. 65% tungsten & 35% zirconium.

10. The temperature at which ferromagnetic material can no longer be
magnetised by the outside forces, is termed as the
A. critical point.
B. curie temperature.
C. inversion temperature.
D. eutectic temperature.

11. Baffles provided on the shell side of a shell and tube heat exchanger
are meant for
A. providing support for the tubes.
B. improving heat transfer.
C. both 'a' & 'b'.
D. preventing the fouling of tubes & stagnation of shell side fluid.

12. When an isolated thermodynamic system executes a process,
A. work is done.
B. heat transfer takes place.
C. mass flow occurs across the boundary of the system.
D. no chemical reaction takes place within the system.

13. Brittleness induced due to the presence of sulphur in steel can be
reduced by adding
A. manganese B. magnesium
C. vanadium D. copper

14. Atomic __________ of an element is a whole number.
A. weight B. number
C. volume D. radius

15. The boiling & freezing points on a newly defined temperature scale
in degree 'D' are 400D & 100D respectively. The temperature
reading corresponding to 60C on this new temperature scale will be
equal to __________ D.
A. 140 B. 180
C. 240 D. 280

16. Which of the following is an unconventional source of energy ?
A. Thermal power
B. Hydroelectric power
C. Nuclear-fusion power
D. Solar power

17. The product (s) of roasting of a sulphide ore is (are)
A. oxide only.
B. sulphate only.
C. oxide and sulphate.
D.
dependent on temperature and partial pressure of oxygen &
sulphur dioxide.

18. Which of the following are considered applications of ultrasonic
testing ?
A. Determination of elastic constant.
B. Detection of defects in metal.
C. Measurement of material thickness.
D. None of the above.

19. Suitability of steel for its use in cable is judged by its strength in
A. tension B. compression
C. torsion D. shear

20. Hydrogen in liquid steels is dissolved
A. as tiny gas bubbles.
B. in the atomic form.
C. in the ionic form.
D. in the molecular form.

21. __________ iron is produced by the annealing of white cast iron.
A. Malleable B. Nodular
C. Ductile D. Grey

22. The mechanism which changes the value of manipulated variable in
response to the output signal from the control unit is called the
A. final control element.
B. on-off control.
C. floating control action.
D. none of these.

23. Fahrenheit and Centigrade scales have the same readings at
A. -55 B. -40
C. -33 D. -58

24. Which of the following low melting alloy containing bismuth and lead
is used for electric fuse ?
A. Wood's metal
B. Babbit metal
C. Monel metal
D. Duralumin

25. Water-tube boiler is the one, in which
A. water passes through tubes and flue gases around it.
B. tube carrying hot flue gases are immersed in a pool of water.
C. tubes are placed in vertical position.
D. none of these.

26. Dephosphorisation of molten pig iron is favoured by
A. oxidising and basic slag.
B. reducing and basic slag.
C. high activity co-efficient of phosphorous in metal.
D. oxidising and neutral slag.

27. In a neutral solution
A. H
+
ions are absent.
B. OH
-
ions are absent.
C.
both H
+
and OH
-
ions are present in very small but equal
concentration.
D. none of these.

28. Which of the following commonly used condenser tube materials has
the lowest thermal conductivity?
A. Admirability brass.
B. Stainless steel.
C. Aluminium brass.
D. Titanium.

29. Strain hardening effect in a metal subjected to cold working is due
to the __________ mechanism.
A. fracture B. dislocation
C. slip D. twinning

30. A common disinfectant used in village wells for disinfection of water
is
A. free chlorine
B. bromine
C. iodine
D. potassium permanganate

31. Moist air is cooled along the line of constant __________ , when it is
passed over a cold & dry cooling coil, such that no condensation
occurs?
A. enthalpy
B. relative humidity
C. wet bulb temperature
D. dew point temperature

32. Which of the following metals can not be hot worked at room
temperature ?
A. Zinc B. Nickel
C. Lead D. Tin

33. Primary designation of steel is based on its
A. hardness & tensile strength.
B. carbon content.
C. iron content.
D. alloying elements content.

34. Steel containing low percentage of nickel, chromium & tungsten are
termed as the __________ steel.
A. wrought
B. tool
C. alloy
D. plain carbon

35. Superheating of steam is done at constant
A. enthalpy B. entropy
C. pressure D. volume

36. A cylinderical rod subjected to a tensile strain within the elastic limit
undergoes a volume change. If the volume strain is equal to half the
tensile strain, then the Poisson's ratio of the rod is
A. 0 B. 0.33
C. 0.44 D. 0.25

37. The surface tension of a liquid, at critical temperature is
A. indeterminate.
B. zero.
C. infinity.
D. same as that at any other temperature.

38. Large scale fire on fuel gas line is normally extinguished by
A. water B. steam
C. foam D. nitrogen

39. Brazing is the joining of metals
A. without melting the base metal.
B. with a non-ferrous filler.
C. both (a) & (b).
D. neither (a) nor (b).

40. Moist climate is the most favourable factor in the site selection far a
A. steel plant
B. textile factory
C. petroleum refinery
D. coke oven battery

41. Dry saturated steam can be converted into superheated steam by
A. increasing its cross-sectional area of flow.
B. passing it through a pressure reducing valve.
C. forcing it downwards through a vertical tube.
D. none of these

42. Pick out the wrong statement.
A. Copper is the metal having the highest electronic conductivity.
B. Hardenability & weldability of metals are inversely related.
C.
Covalant bonding formed by sharing of electrons is present in all
semi-conductor materials.
D.
Glass transition temperature applies to 'polymers' but not to
'glasses'.

43. Increasing sulphur content in pig iron tends to make it
A. soft
B. hard
C. tough
D. ductile & malleable

44. Oxyacetylene reducing flame is used while carrying out welding on
A. alloy steel
B. grey cast iron
C. mild steel
D. high carbon steel

45. M10 index of coke indicates its
A. compressive strength.
B. hardness.
C. abrasion resistance.
D. impact strength.

46. Gantt charts are used for streamlining the
A. inventory control
B. production schedule
C. sales forecasting
D. quality control

47. In the Bayer's process, bauxite is digested under pressure using
A. H2SO4 B. NaOH
C. NH3 D. HCl

48. Circular cross section machine parts which are symmetrical about
the axis of rotation are made by hot
A. piercing B. spinning
C. drawing D. extrusion

49. The substance used as a smoke screen in warfare is
A. C2H2 B. SiCl4
C. P2O5 D. PCl5

50. The same volume of all gases is representative of their
A. specific gravities.
B. densities.
C. gas characteristic constants.
D. molecular weights.


































SECTION 4
1. Fluorine is not a constituent of
A. freon B. chloroform
C. teflon D. fluorocarbons

2. The most commonly used combustion system manufactured in India
for the thermal power plant boilers is the __________ combustion
system.
A. pulverised fuel
B. travelling grate stoker firing
C. circulating fluidised bed
D. fluidised bed

3. During solid state sintering of powders, the following mechanism can
be active.
A. Evaporation and condensation.
B. Solid state diffusion processes.
C. Liquid formation in grain boundaries.
D. Creation of more dislocations.

4. The transition temperature at which all the ferromagnetic materials
become paramagnetic materials is termed as the 'Curie temperature'.
Its value for cobalt is __________ C.
A. 768 B. 1127
C. 1359 D. 1480

5. Regeneration of molecular seive requires it to be heated to a
temperature of about __________ C.
A. 80-120 B. 200-300
C. 600-800 D. 1000-1100

6. The ultimate strength in tension for steel is __________ times the
ultimate strength in shear.
A. 0.5 B. 0.9
C. 1.5 D. 2.5

7. The activity of pure hydrogen gas at 1000C and 5 atm pressure
A. is always less than 1.
B. is always greater than 1.
C. can be 5.
D. depends on the choice of the standard state.

8. Which of the following transducers is most commonly used for the
measurement of shock and vibration ?
A. Linear variable differential transducer (LVDT)
B. Dial gauge
C. Accelerometer
D. none of these

9. The power of a low capacity prime mover is most suitably measured
by a __________ type dynamometer.
A. driving
B. transmission
C. absorption
D. none of these

10. __________ addition increases the depth of hardness of steel.
A. Chromium B. Nickel
C. Tungsten D. Vanadium

11. The most important consideration in value engineering is the
A. profit maximisation.
B. customer satisfaction.
C. cost reduction.
D. process improvement.

12. Lime contains about 90% CaO. Percentage CaO present in limestone
is about
A. 25 B. 50
C. 70 D. 80

13. The most important material handling system in an integrated steel
plant is the
A. belt conveyor
B. diesel locomotive
C. truck
D. overhead hoists & cranes

14. Property of a material to resist a tensile force without giving away is
a measure of its
A. stiffness B. toughness
C. resilience D. tenacity

15. Cast iron has the unique property of high
A. ductility
B. damping characteristics
C. hardness
D. malleability

16. Steels with high carbon equivalent have poor weldability, because in
these steels during welding
A.
carbon and other alloying elements get oxidised from the weld
pool.
B.
excessive ferrite forms in the heat affected zone leading to poor
toughness of the weld.
C. martensite forms in the heat affected zone leading to poor
toughness/ductility of the weld.
D.
segregation of carbon and other element occurs in the weld pool
leading to poor properties of the weld.

17. If the pH value of a solution of sodium chloride is 7; then what will
be the pH value of the solution after its electrolysis ?
A. 7
B. < 7
C. > 7
D. 0

18. Measurement of the area of the indented surface is not involved in
the __________ hardhes testing method.
A. Vicker's B. Rockwell
C. Knoop D. Brinell

19. Salvage value is the most flexible criteria for analysing a financial
investment. 'Salvaging' means
A. disposing off a machine/property on as is where is basis.
B.
disposing off machine/property, which is no longer useful in the
present scenerio.
C. mortgaging the obsolete machine/property.
D. writing off the obsolete machine/ property.

20. Super conduction in metals is observed at a temperature of
__________ K.
A. <100
B. >100
C. about 273
D. about 373

21. Springback in sheet metal bending depends on the
A. elastic limit
B. bend radius
C. degree of bend
D. thickness of sheet

22. The yield point in fatigue loading compared to that in static loading
is less. The ratio of ultimate tensile strength to endurance limit of a
material subjected to fatigue loading is
A. 0.5 B. 1
C. 1.5 D. 2

23. Which of the following is not used as a fuel in rocket propellaht ?
A. Liquid hydrogen
B. Liquid oxygen
C. Liquid hydrazine
D. Kerosene oil

24. Hypo (sodium thiosulphate) because of its complex forming
behaviour is used in photography to remove undecomposed silver
bromide as a soluble complex for __________ of the picture.
A. printing B. developing
C. colour D. fixation

25. Temperature of hot gases flowing in a pipe is measured by a
thermocouple inserted in the thermal well. The thermal well made of
__________ will facilitate the most accurate measurement of the
temperature.
A. copper B. steel
C. aluminium D. brass

26. __________ welding will be the most suitable for butt welding two 20
cms thick boiler drum mild steel plates.
A. Electrical resistance
B. Electroslag
C. Plasma torch
D. Submerged arc

27. Machinability of hard alloys & tool steels is improved by
A. spherodising B. annealing
C. tempering D. normalising

28. LASER
A.
stands for Light Amplification by Stimulated Emission of
Radiation.
B. has the same intensity as visible light.
C. can't be used for cutting metals.
D. none of these.

29. __________ forces do not act in case of fluids.
A. Vibratory B. Centrifugal
C. Elastic D. Tensile

30. Which of the following is not a natural abrasive ?
A. Silicon carbide
B. Quartz
C. Corundum
D. Emery

31. The function of a nozzle provided in steam turbine is to
A. throttle down (i.e., reduce) the pressure of steam.
B. convert internal energy into kinetic energy.
C. increase the velocity of steam.
D. all (a), (b) & (c).

32. Which of the following polymers is obtained by copolymerisation of
three monomers ?
A. SAN B. ABS
C. SBR D. PTFE

33. Silicon percentage in the silicon steel used for electrical
appliances/equipments is
A. 0.3-0.4 B. 12-14
C. 3-4 D. 20-25

34. Material of construction of foundary crucible is
A. graphite
B. lead
C. porcelain
D. stainless steel

35. Titanium can be easily welded using __________ welding.
A. submerged arc
B. TIG
C. shielded metal arc
D. electroslag

36. Feed check valve is used in steam boilers to
A. check the water level in the boiler.
B. check the feed water flow rate.
C.
feed high pressure water to boiler and guard against its backflow
through it.
D. none of these.

37. Three elastic constants for a completely anisotropic elastic material
which follows the Hooke's law are young's modulus, elastic limit
stress and yield stress. Which of the following properties is most
sensitive to increase in strain rate ?
A. Tensile strength.
B. Elastic limit.
C. Proportional limit.
D. Yield strength.

38. Swaging is a/an __________ operation.
A. piercing B. forging
C. extrusion D. drawing

39. Pig iron is
A. made from cast iron.
B. made from wrought iron.
C. the one, which comes out of the blast furnace.
D. free from impurities.

40. Classification of metal forming processes into hot and cold working
is based on the following parameters.
A. Stacking fault energy.
B. Recrystallisation temperature.
C. Solidus temperature.
D. Transformation temperature.

41. Kinematic viscosity of water as compared to that of air is
A. more
B. same
C. 15% more
D. 15% less

42. Which of the following is the most suitable for removing fine
particles (< 1 micron diameter) from air below its dew point ?
A. Venturi scrubber
B. Electrostatic precipitator
C. Cyclone separator
D. Fabric filter

43. Which of the following is the terminology used for the temperature at
which the phase changes occur in a metal ?
A. Critical temperature.
B. Recrystallisation temperature.
C. Phase transformation temperature.
D. Transition temperature.

44. Puddling process is used for converting pig iron into
A. cast iron
B. wrought iron
C. mild steel
D. semi-steel

45. Addition of __________ in steel can help in increasing the depth of
hardness.
A. nickel B. chromium
C. vanadium D. tungsten

46. On-off control
A.
fully opens the final control element, when the measured variable
is below the set point.
B.
fully closes the final control element, when the measured variable
is above the set point.
C.
is a two position control (fully open or fully closed) control
adequate to control a process with slow reaction and minimum
dead time or transfer lag.
D. none of these.

47. The tensile load-elongation curve of a metal does not describe
A. work hardening
B. yield stress
C. anisotropy index
D. necking strain

48. Usual value of the resistance suitable for a wire resistance strain
gauge is __________ ohms.
A. 20 B. 80
C. 120 D. 500

49. Permanent set in a material is produced by subjecting it to
A. triaxial loading.
B. fatigue loading.
C. stresses beyond the elastic limit.
D. tensile & compressive loads simultaneously.

50. The following is a typical anionic collector used in flotation.
A. Ethyl dixanthogen.
B. Trimethyl cetyl ammonium bromide.
C. Potassium ethyl xanthate.
D. lAuryl amine hydrochloride.


























SECTION 5
1. A solution which resists change in its pH value on addition of
acid/alkali is called the __________ solution.
A. neutral
B. ideal
C. buffer
D. zero pH

2. Pick out the wrong statement.
A.
Weldability of high carbon steel is poorer compared to low carbon
steel.
B. Invar is a magnetic alloy.
C.
Magnetic permeability of the diamagenetic material is less than
one.
D.
Martensitic transformation never goes to complection ( i.e., 100%)
at room temperature.

3. The bolt is subjected to __________ when the nut is tightened by
putting the washer beneath it.
A. tension
B. shear
C. compression
D. bending & tension

4. Which of the following is not categorised as the ore agglomeration
process ?
A. Nodulising B. Pelletising
C. Balling D. Briquetting

5. With increase in temperature, the surface tension of water
A. increases
B. decreases
C. remains constant
D. increases linearly

6. A reduction in thermal resistance during heat transfer does not occur
in the
A.
convection heat transfer by stirring the fluid and cleaning the
heating surface.
B.
conduction heat transfer by reduction in the material thickness
and increase in the thermal conductivity.
C.
radiation heat transfer by increasing the temperature and reducing
the emis-sivity.
D. none of these.

7. Unit of viscosity in CGS system is
A. gm .cm
-1
sec
-1

B. gm . cm
2
. sec
-2

C. gm .cm
-2
, sec
-1

D. gm . cm . sec
-1


8. Shaft/rotor speed is most accurately measured by a
A. frequency counter.
B. tachometer.
C. strobometer.
D. speedometer.

9. __________ test determines the yield strength, Young's modulus of
elasticity, percentage reduction in area & percentage elongation of a
material.
A. Tensile
B. Fatigue
C. Impact
D. None of these

10. The rolling process can not be used to produce
A. plates B. rods
C. tubes D. wires

11. Co-efficient of performance of a Carnot cycle refrigerator operating
between - 23C and + 27C is
A. 3 B. 5
C. 0.5 D. 1.5

12. Presence of nickel & chromium in steel does not raise its
A. elastic limit
B. machining properties
C. ductility
D. resilience

13. Hot extrusion process is not used for making
A. cast iron pipe for domestic water supply.
B. aluminium curtain rods.
C. stainless steel tubes used in furnitures.
D. any of these.

14. Addition of __________ to steel does not help in improving its
machinability.
A. sulphur B. silicon
C. lead D. phosphorous

15. Quartz is a __________ material.
A. diamagnetic B. ferromagnetic
C. ferroelectric D. piezoelectric

16. The units of the rate constant for a second order reaction are
A. sec
-1
. mole.
B. moles
1
. sec
-1
.
C. moles
-1
. sec
1
.
D. moles
1
. sec
1
.

17. The most serious manufacturing defect from fracture toughness
point of view is
A. surface roughness
B. pores
C. spherical inclusion
D. crack

18. Leakage in a cooking gas cylinder is detected by
A. radio-isotopes.
B.
pouring soap solution on the surface and locating the gas
bubbles.
C. halide torch.
D. pungent smell of mercaptans present in the gas.

19. Which of the following is the most wear resistant grade of carbide
used for the cutting tools?
A. Aluminium carbide
B. Tungsten carbide
C. Nickel carbide
D. Iron carbide

20. The ratio of mass of a neutron to that of an electron is about 1839.
What is the ratio of the mass of a proton to that of an electron?
A. 159 B. 1837
C. 2537 D. 10000

21. Laser is a device to produce
A. gamma rays.
B. microwaves.
C. a beam of white light.
D. a beam of coherent light.

22. Addition of small amount of __________ to grey cast iron is done to
produce nodular grey cast iron.
A. manganese B. phosphorous
C. magnesium D. chromium

23. Minimum thermal efficiency of a steam boiler may be around
__________ percent
A. 25 B. 45
C. 65 D. 20

24. The temperature at which the magnetic property of iron disappears
(i.e., it becomes non-magnetic) and its electrical conductivity &
specific heat also changes, is called the 'Curie point', which is
__________ C.
A. 768 B. 908
C. 1400 D. 1539

25. Fatigue limit improvement by over stressing the metal by
successively increasing the load is called coaxing. In fatigue failure,
the material fails
A. below the yield point.
B. above the yield point.
C. below the elastic limit.
D. at the elastic limit.

26. The malleability of a material is the property by virtue of which it
can be rolled or hammered into thin sheets. Which of the following
materials has the maximum malleability ?
A. Lead
B. Copper
C. Aluminium
D. Wrought iron

27. Particle nature of cathode rays is proved due to the fact that they
A. travel in a straight line.
B. get deflected by magnetic electric field.
C. produce fluorescence.
D. heat the exposed material.

28. The most commonly used moderator in nuclear power plants is
A. graphite
B. light water
C. heavy water
D. berellium

29. Babbit lining is used on brass/bronze bearings to increase the
A. antifriction properties.
B. compressive strength.
C. bearing resistance.
D. wear resistance.

30. The heat of neutralisation remains constant, when there is a
reaction between dilute solutions of strong
A. base and strong acid.
B. base and weak acid.
C. acid and weak base.
D. none of these.

31. Joining of thin foils is preferred to be done by
A. gamma rays
B. X-rays
C. microwaves
D. gas welding

32. Which of the following metals reacts violently with water ?
A. Mercury B. Sodium
C. Calcium D. Magnesium

33. A steam carraying pipeline is insulated with two layers of insulating
materials with the inferior insulation material forming the inner
part. If the two insulating layers are interchanged, the heat
conducted will
A. increase.
B. decrease.
C. remain unaffected.
D. may increase or decrease; depends on the thickness of each layer.

34. Damage to metal surface by mechanical action is called
A. pitting
B. corrosion
C. erosion
D. none of these

35. The escape velocity of a body on earth which is independent of its
mass is about __________ km/second.
A. 3 B. 7
C. 11 D. 15

36. Which of the following test is used for distinguishing among dry oils,
semi-drying oils and non drying oils ?
A. Elaiden test
B. Reichart-Meissl value test
C. Henter value test
D. Iodine value test

37. The wet bulb temperature is lower in dry air than in wet air at the
same temperature. A dry bulb thermometer registers a higher
temperature than a wet bulb thermometer except at __________
percent relative humidity.
A. 0
B. 100
C. 50
D. none of these

38. The process of removal of scale formed during hot rolling of steel is
termed as
A. descaling
B. shot blasting
C. pickling
D. skimming

39. A psychrometer does not measure the __________ temperature of
moist air.
A. dew point
B. dry bulb
C. wet bulb
D. none of these

40. An ideal material for making cooking vessels should have
A. high heat capacity.
B. low heat capacity.
C. high thermal conductivity.
D. both (b) and (c).

41. Which of the following approaches the ideal gas behaviour most
closely ?
A. Wet steam
B. Saturated steam
C. Superheated steam
D. Saturated water

42. Which of the following is not the function of a volute casing provided
in a centrifugal pump ?
A. To reduce the head loss in discharge.
B. To increase the pump efficiency.
C.
To collect liquid from the periphery of the impeller and to transmit
it to the delivery pipe at constant velocity.
D. To increase the pump discharge rate.

43. The pressure outside a bubble/droplet of liquid is __________ the
internal pressure.
A. greater than
B. less than
C. equal to
D. unpredictable ; depends on the bubble size

44. Two wires of the same radius & material having length in the ratio of
1 : 2 are stretched by the same force. The strain produced in the two
wires will be in the ratio of
A. 1:1 B. 1:2
C. 2:1 D. 1:4

45. Powder metallurgy technique is used in the production of __________
tools.
A. tungsten carbide
B. high carbon steel
C. high speed steel
D. drilling

46. Principal alloying elements of cast tool alloys which have very high
wear resistance & high temperature strength are
A. cobalt, chromium & tungsten,
B. cobalt, chromium & nickel.
C. molybdenun, tungsten & chromium.
D. cobalt, zirconium & molybdenum.

47. Which of the following is the most suitable material of construction
for the condenser tubes, where the cooling medium is brine (salty
water)?
A. Aluminium
B. Copper
C. Titanium
D. Stainless steel

48. Which of the following is an ore dressing operation ?
A. Classification
B. Smelting
C. Roasting
D. None of these

49. Gratings is associated with the measurement of
A. linear displacement.
B. concavity/convexity.
C. surface texture.
D. flatness.

50. __________ joint is mostly used for joining pipes carrying water at low
pressure.
A. Nipple
B. Socket
C. Union
D. Bell and spigot











SECTION 6
1. Adhesives
A. can't be used in the form of pressure sensitive tapes.
B. can't join two dissimilar metals.
C. cure instantaneously after application on a surface.
D. none of these.

2. In a counter flow heat exchanger, hot fluid enters at 170C & leaves
at 150C, while the cold fluid enters at 50C & leaves at 70C. The
arithmetic mean temperature difference in this case is __________ C.
A. 20 B. 60
C. 120 D.

3. Normalising of a casting does not
A. induce stresses in it.
B. refine its grain structure.
C. reduce seggregation.
D. improve its mechanical properties.

4. The swift cup test evaluates the following property of a sheet metal.
A. Stretchability
B. Drawability
C. Bendability
D. None of these

5. __________ is the most important element, which controls the physical
properties of steel.
A. Manganese B. Silicon
C. Carbon D. Vanadium

6.
The emf of a Deniell cell can be increased by
A. decreasing the surface area of the electrodes.
B. increasing the concentration of zinc sulphate solution.
C. increasing the surface area of the electrodes.
D. increasing the concentration of copper sulphate solution.

7. A hot short metal is
A. hard when hot.
B. brittle when cold.
C. brittle when hot.
D. brittle under all conditions.

8. Corrosion rate can not be lowered by reducing the __________ of the
corroding medium.
A. concentration
B. velocity
C. temperature
D. none of these

9. Routing in production, planning & control is concerned with the
A. sequence of operation to be performed.
B. progress of work performed.
C. authorisation of work to be performed.
D. balancing of load on machines.

10. A fire tube boiler is limited to a maximum steam pressure of about
__________ kg/cm
2
.
A. 6 B. 18
C. 38 D. 52

11. The total frictional resistance to fluid flow does not depend upon the
A. roughness of the surface.
B. fluid pressure.
C. fluid density.
D. fluid velocity.

12. Stretcher strains found in a low carbon sheet are associated with the
A. texture.
B. dislocation density.
C. yield point phenomenon.
D. thickness of the sheet.

13. The most important consideration, while designing the refrigeration
system of an aircraft is that the refrigeration system
A. is as light as possible.
B. has very high C.O.P.
C. employs minimum quantity of refrigerant.
D. consumer minimum horse power.

14. Though tin occurs lower than iron in the electrochemical series, yet
it is coated on steel for corrosion protection, because of its
A. lower cost.
B. abundant availability.
C.
resistance to vegetable acids as the tin plate are commercially
used in 'canning' industry.
D. none of these.

15. Which of the following is resistant to the action of both heat &
chemicals ?
A. Boro silicate glass,
B. Silica glass.
C. Soda lime glass.
D. none of these.

16. Metallic surveying tapes are made of __________ which has a low co-
efficient of expansion & enough strength.
A. invar
B. hastealloy
C. duralumin
D. monel metal

17. Which of the following is a unit of time ?
A. Barn
B. Light year
C. Angstrom
D. none of these

18. __________ furnace is generally used in the non-ferrous foundaries.
A. Direct arc
B. Indirect arc
C. Resistance
D. Induction

19. Steel & cast iron pipes are produced by __________ casting.
A. slush
B. die
C. investment
D. true centrifugal

20. The taper provided on pattern for its easy & clean withdrawal from
the mould is termed as the __________ allowance.
A. casting B. pattern
C. draft D. distoration

21. Gas turbine normally employs a constant __________ cycle.
A. pressure
B. temperature
C. volume
D. none of these

22. Which of the following relationships is correct for relating the three
elastic constants of an isotropic elastic material (where, E = Young's
modulus, G = Modulus of rigidity or shear modulus v = Poisson's
ratio) ?
A. E = 2G (1 + v)
B. E = G (1 + v)
C. E = G (1 + v)/2
D. E = 2G (1 + 2v)

23. Electrostatic separation of minerals from each other is based on
their differences in the following property.
A. Densities.
B. Magnetic permeabilities.
C. Electrical conductivities.
D. Hardness.

24. Natural water contains approximately __________ percent of heavy
water.
A. 0.015 B. 0.71
C. 1.2 D. 3.5

25. The minimum temperature to which the water can be cooled in a
cooling tower is the __________ temperature of air.
A. ambient
B. dry bulb
C. dew point
D. wet bulb

26. The order of a chemical reaction
A. can be determined only experimentally
B. can be determined from the stoichiometry of the reaction.
C. can not be zero.
D. can be fractional.

27. Pick out the wrong statement.
A. Lead can creep under its own weight at room temperature.
B.
The electrical conductivity of gold is considerably reduced by
alloying additions due to the decrease in electron movement.
C.
Recrystallisation temperature decreases with decrease in strain in
a cold worked metal.
D.
With increase in temperature, the electrical conductivity of
intrinsic semi-conductor will increase.

28. Pick out the wrong statement.
A. Reflectivity of gases is very low.
B. Absorptivity for metals is very high.
C. Reflectivity for non-conducting materials is low.
D. Reflectivity of polished surfaces is very high.

29. For efficient performance of a blast furnace, the extent of reduction
of Wustite (FeO) should be
A. 100% indirect reduction.
B. 100% direct reduction.
C. 50-60% indirect reduction.
D. 30-40% indirect reduction.

30. Identify the false statement
A.
Martensitic steels are less susceptible to pitting corrosion than
austenitic steels.
B. Pitting corrosion is usually very localised.
C. Hydrogen embrittlement is facilitated by tensile stress.
D. Stress corrosion cracking is facilitated by tensile stress.

31. __________ can replace tungsten in high speed steel.
A. Chromium B. Vanadium
C. Cobalt D. Molybdenum

32. Production of one ton of paper in Indian paper industry consumes
about __________ kWh of electricity.
A. 300 B. 800
C. 1400 D. 2000

33. Fatigue strength of a material can not be increased by
A. cold working
B. hot working
C. shot peening
D. any of these

34. Steel rods are normally used for concrete reinforcement because
concrete and steel have almost equal
A. tensile strength.
B. compressive strength.
C. Young's modulus.
D. thermal co-efficient of expansion.

35. Out of the following the refractive index is the highest for
A. glass B. diamond
C. brine D. kerosene

36. Function of blow down valve in a boiler is to
A. maintain the drum level.
B. keep the drum pressure constant.
C. drain out the sludge from the drum.
D. empty the boiler during shutdown.

37. Insulation of liquid surface can be achieved by __________ on top of
its surface.
A. floating hollow polypropylene spheres
B. spraying alumina powder
C. putting cement
D. none of these

38. Consider an ideal solution of components A and B. The entropy of
mixing per mole of an alloy containing 50 wt% B is
A. R ln 2
B. -R ln 2
C. 3 R ln 2
D. -3R ln 2

39. Out of the following, the lowest packing of atoms exists in __________
crystal lattice structure.
A. hexagonal close, packed (hcp)
B. face centred cubic (fcc)
C. body centred cubic (bcc)
D. simple cubic

40. Cadmium in zinc leach liquor is removed by cementation using
A. zinc B. iron
C. nickel D. copper

41. In electrical resistance welding, distortion results from the use of
improper
A. clamping methods
B. electrodes
C. current
D. filler material

42. The conventional mechnical transducer, which converts pressure
signal to displacement signal is
A. spring
B. manometer
C. strain gauge
D. none of these

43. Pick out the wrong statement.
A.
Seam welding, projection welding & spot welding are the
classification of electrical resistance welding.
B.
Electrode tip in spot welding is of copper and the tip diameter
should be equal to t (where, t = plate thickness to be welded)
C.
In spot welding, two pieces to be joined are overlapped and placed
between two electrodes.
D. Mild steel sheet can not be spot welded.

44. Austempering of steel requires.it to be heated to 875C followed by
sudden cooling to 250-525C, thereby changing austenite to
A. sorbite B. bainite
C. martensite D. troostite

45. A compact estimate about the amount of materials handling between
various work stations is obtained from the
A. gantt chart
B. bin chart
C. string diagram
D. travel chart

46. Lead is poured into the joint between two- __________ pipes.
A. mild steel
B. concrete
C. cast iron
D. asbestos cement

47. The concentration of (H
+
) ions is 4 x 10
-5
in a solution. Then pH of
the solution will be (Given log 4 = 0.6 )
A. 4.4 B. 5.6
C. 8.4 D. 2.4

48. Age hardening is connected with
A. babbit metal
B. gun metal
C. stainless steel
D. duralumin

49. With decrease in the grain size of a material, its creep resistance
A. increases.
B. decreases.
C. remains constant.
D. either (a) or (b) ; depends on the material.

50. __________ rubber is generally used for making 'O' rings used for
vacuum sealings.
A. Natural B. Neoprene
C. Butadiene D. Nitrile























SECTION 7
1. Gross national product (GNP) means the total value of __________ in a
country.
A. goods produced
B. gold reserve
C. earning of the citizens
D. taxes paid

2. Energy to be supplied to the radioactive nucleus for the emission of a
neutron is __________ MeV.
A. 0.8 B. 7.8
C. 200 D. 10000

3. The co-ordination number in simple cubic structure is
A. 4 B. 6
C. 8 D. 12

4. Out of the following surfaces, the emis-sivity will be minimum for
A. aluminium foil
B. concrete
C. plaster
D. smooth glass

5. The property of material, by which a given amount of energy is
absorbed by it without plastic deformation, is called the
A. resilience
B. toughness
C. ductility
D. impact strength

6. The size of the tetrahedral void in the closest packing of atoms is
__________ that of the octahedral void.
A. equal to
B. greater than
C. less than
D. either (a), (b) or (c); depends on the size of atom

7. __________ the exhaust gas is an indication of the incomplete
combustion of fuel.
A. Low temperature of
B. High temperature of
C. High % of CO in
D. High % of CO2 in

8. Air/fuel ratio on molar (volume) basis for combustion of methane with
theoretical quantity of air with be
A. 9.5:1
B. 12.5:1
C. 15.5 :1
D. 18.5 : 1

9. Frost formation on the evaporator tubes in the domestic refrigerators
A. can be prevented by proper design.
B. decreased compressor power.
C. causes heat loss due to poor heat transfer.
D. is immaterial.

10. Function of feed check valve in a boiler is to
A. facilitate circulation of high pressure feed water.
B. check the water level in the boiler drum.
C. prevent the back flow of water.
D. regulate the water flow to boiler.

11. Ganister contains maximum percentage of
A. FeO B. SiO2
C. MgO D. MnO2

12. Nitrogen is not an essential component of
A. protein
B. urea
C. oils & fats
D. any of these

13. In inventory control theory, the economic order quantity (EOQ) is the
A. lot size corresponding to break even analysis.
B. average level of inventory.
C. optimum lot size.
D. none of these.

14. The main charge in blast furnace is usually
A. iron ore & coke.
B. iron ore, coke & air.
C. limestone, coke & iron ore.
D. limestone, sand & iron ore.

15. The atmospheric temperature during melting of ice/snow (in the
atmosphere)
A. decreases
B. increases
C. remains same
D.
may increase or decrease ; depends on the altitude where snow
melts

16. At room temperature, F.C.C. crystal structure is observed in
A. lead B. cupro-nickel
C. titanium D. tungsten

17. The basic function of the drum in a boiler is to
A. act as a storage for feed water.
B. act as a storage for steam.
C. separate steam from water.
D. remove settling impurities from steam.

18. Pick out the wrong statement.
A.
The X-rays can not be deflected by electric field unlike cathode
rays.
B.
The intensity of X-rays can be measured by ionisation current
produced due to the ionisation of gas by X-rays.
C.
The quality of X-rays can be controlled by varying the anode-
cathode voltage.
D.
Crystal structure of a material can be studied by an electron
microscope.

19. Colloids can be purified by
A. dialysis
B. reverse osmosis
C. coagulation
D. peptization

20. The most prominent single cause of corrosion in boilertubes, drums,
economisers and steam superheaters in a thermal power plant boiler
is the
A. water alkalinity & leakage.
B. hydrazine addition during feed water treatment.
C. release of non-condensable gas from water in the boiler.
D. scale formation.

Prev 12345678910Next
21. Maximum carbon content in cast iron is __________ percent.
A. 3.8 B. 4
C. 4.3 D. 4.6

22. Screws are specified by their __________ diameters.
A. minor
B. major
C. pitch
D. none of these

23. The stress at which extension of the material takes place more
rapidly as compared to the increase in load is termed as the
__________ point of the material.
A. elastic B. ultimate
C. yielding D. breaking

24. A material being tested for endurance strength is subjected to the
__________ load.
A. impact
B. completely reversed
C. dynamic
D. static & dynamic

25. With increase in pressure, the latent heat of steam
A. increases.
B. decreases.
C. remains unchanged.
D. data insufficient; can't be predicted.

26. 'Flare tower' used in industry is meant for
A.
venting off (after burning) the excess inflammable/toxic gases at
high pressure.
B. absorbing the pollutant gases from the furnace exhaust.
C. cooling of furnace exhaust gases.
D. none of these.

27. Which of the following has the highest modulus of elasticity (about 7
x 10
6
kg/cm
2
) ?
A. High speed steel
B. Stainless steel
C. Tungsten carbide
D. Superalloys

28. Electrolytic reduction cell used for conversion of calcined Al2O3 to Al
is a carbon lined furnace operating at 800-900 C. The purpose of
electric current supplied to the furnace is to
A. achieve very high purity of aluminium (99.9%).
B. keep the electrolyte in liquid condition by the generation of heat.
C. electrolytically dissociate alumina.
D. both(b) & (c).

29. All radiations falling on a black body are
A. refracted B. reflected
C. transmitted D. absorbed

30. Styrofoam is the commercial name of
A. polyurathene B. polystyrene
C. polyacrylonitrile D. polybutadiene

31. Ceramic materials are
A. organic in nature.
B. stronger in compression than in tension.
C. always amorphous in nature.
D. always bad heat conductors.

32. Dryness fraction of dry steam is
A. 0 B.
C. 1 D. 0.5

33. Which of the following processes follows the hardening process for
reducing the hardening strains & increasing the toughness of the
steel part?
A. Anodising B. Tempering
C. Carburising D. Annealing

34. Heat required to raise the temperature of a body by 1 C is called its
A. heat capacity.
B. specific heat capacity.
C. thermal conductivity.
D. water equivalent.

35. Coating of zinc over steel is known as
A. cladding B. galvanising
C. anodising D. passivation

36. Air-petrol ratio in an automotive petrol engine is around
A. 14 : 1
B. 22 : 1
C. 25 : 1
D. 4 : 1

37. The property of material, by which a given amount of energy is
absorbed by it, without plastic deformation is called
A. resilience
B. toughness
C. ductility
D. impact strength

38. Sacrificial anode method is used in the protection of pipelines which
are buried underground. Sacrificial anode
A. occurs higher in the electro-chemical series of metals.
B. is exemplified by magnesium plate.
C.
is much cheaper than the cathodic base material to be guarded
against corrosion.
D. all (a), (b) & (c).

39. Electrochemical corrosion can occur, only if __________ is present in
contact with metal.
A. air
B. oxygen
C. liquid medium
D. gaseous medium

40. Crystallisation of polymers is an undesirable property.
Crystallisation of celluloid is prevented by adding
A. glycerol
B. nitro cellulose
C. camphor
D. none of these

41. Preheating prior to welding is done for the purpose of
A. decreasing cooling rate.
B. facilitating fusion of high melting metals.
C. preventing hot cracking.
D. ensuring full penetration.

42. Presence of sulphur in steel reduces the
A. hardness.
B. grain size.
C. tensile strength.
D. toughness & transverse ductility.

43. Frother is added in the froth floatation cell used in ore beneficiation
to stabilise the air bubbles (i.e., froth), which will hold the ore
particles, but it does not affect the floatability of minerals. Which of
the following is not used as a frother?
A. Cresylic acid
B. Xanthaies
C. Pine oil
D. all 'a' 'b' & 'c'

44. Otto cycle used in spark ignition petrol engines is also known as the
constant __________ cycle.
A. volume
B. pressure
C. heat
D. none of these

45. Fire on fuel oil lines can be extinguished by
A. foam
B. steam
C. water
D. carbon dioxide

46. In a furnace with heating element temperature at 1700C, the
dominant machanism of heat transfer will be
A. conduction
B. radiation
C. natural convection
D. forced convection

47. Optical activity is a/an __________ property.
A. additive
B. constitutive
C. both (a) & (b)
D. neither (a) nor (b)

48. Solution loss reaction occurs
A. in the blast furnace shaft.
B. during pretreatment of hot metal.
C. in the L.D. process.
D. during deoxidation in the ladle.

49. Out of the following materials, the one which generally exhibits an
yield point is
A. hard bronze
B. soft brass
C. cold rolled mild steel
D. hot rolled mild steel

50. The efficiency of a Carnot heat engine operating between absolute
temperatures T1 and T2 (when, T1 > T2) is given by (T1 - T2)/T1. The
co-efficient of performance (CO.P.) of a Carnot heat pump operating
between T1 and T2 is given by
A. T1/(T1-T2) B. T2/(T1-T2)
C. T1/T2 D. T2/T1






















SECTION 8
1. Diamagnetic materials
A. are magnetised by eddy currents only.
B. are non-magnetic and cannot be magnetised.
C. are magnetised in direction opposite to the magnetic field.
D. can be magnetised in one direction only.

2. In connection with corrosion of metals, passivation is the process that
A. intensifies deterioration.
B. changes the composition of the metal.
C. inhibits further deterioration.
D. none of these.

3. With increase in impurities in metals, their corrosion resistances
A. increase
B. decrease
C. remain same
D. may increase or decrease ; depending on the type of metal

4. Most important property of steels for use in automobile bodies is the
A. formability
B. yield strength
C. toughness
D. resilience

5. Consideration of the creep is the most important in case of the
A. blades of gas turbine.
B. piston of an I. C. engine.
C. flywheel of steam engine.
D. cycle chain.

6. Non-ferrous alloys used for making cutting tools need not have high
A. abrasion resistance
B. toughness
C. red hardness
D. cutting speed

7. Hollow shafts can be made as strong as solid shafts by making the
twisting moments of both the shafts same. Shafts made by __________
have residual stresses.
A. forging
B. cold rolling
C. hot rolling
D. casting

8. Capacity & power requirement for an air compressor working at high
altitude compared to sea-level will be
A. more
B. less
C. same
D. either more or less; depends on the climatic conditions.

9. Glycerene is used as a coolant in cooling of some engines instead of
water, because
A. its higher boiling point (290C) increases its heat carrying capacity.
B. compartively less weight of coolant is required.
C. smaller radiator can be used.
D. all a, b & c.

10. Cold working of a material results in increase in hardness, which is
termed as the __________ hardening.
A. cold B. work
C. age D. induction

11. Potable water means the water used for
A. fire-fighting
B. cooling
C. drinking
D. evaporation to produce steam

12. One ton of refrigeration is not equivalent to the heat removal rate of
A. 200 BTU/minute
B. 50 kcal/minute
C. 50 kJ/sec.
D. 3.5 KW

13. Starting friction is low in case of the __________ lubrication.
A. boundary B. hydrodynamic
C. hydrostatic D. mixed/semi-fluid

14. Ultimate strength in tension as compared to that in shear for steel is
A. half
B. one third
C. one and half times
D. one fourth

15. Which of the following heat treatment processes is usually applied to
castings ?
A. Tempering B. Annealing
C. Normalising D. Carburising

16. Photographic plates are coated with
A. silver nitrate
B. silver halide
C. calcium silicate
D. metallic silver

17. Hardening of steel is not possible, unless it is heated __________
critical point.
A. above the highest
B. above the lowest
C. between the first & second
D. between the second & third

18. Isotropic materials have the same __________ in all directions.
A. induced stresses
B. density
C. elastic properties
D. thermal properties

19. The most important requirement for aluminium industry is the
availability of cheap
A. ore
B. electrical power
C. labour
D. & abundant water

20. Spheriodising of a material is a/an __________ process.
A. normalising B. annealing
C. tempering D. hardening

21. The trace metal present in insulin is
A. Cu B. Zn
C. Fe D. Ni

22. Cold cracking in the heat affected zone of a high strength steel weld
can take place because of the
A. retained austenite.
B. martensite formation.
C. relatively high sulphur content in the base metal.
D. sufficient hydrogen present in the welding arc.

23. Drossing is a __________ operation.
A. smelting B. dressing
C. roasting D. dressing

24. Most of the phosphorous present in the blast furnace burden enters
into
A. hot metal
B. flue gases
C. slag
D. refractory lining

25. During sensible heating of humid air
A. relative humidity increases.
B. dew point remains constant.
C. dry bulb & wet bulb temperature increases.
D. both 'b' & 'c'.

26. Iron content in Indian iron ore is about __________ percent.
A. 80-85 B. 60-65
C. 40-45 D. 20-25

27. The heat treatment to which the steel wire containing > 0.25%
carbon is subjected to is
A. full annealing
B. bright annealing
C. patenting
D. none of these

28. __________ of hard alloy and tool steel is done to make it easily
machinable.
A. Case carburising
B. Tempering
C. Normalising
D. Annealing

29. Which of the following mainly decides the current to be employed is
arc welding ?
A. Electrode size
B. Plate thickness
C. Voltage across the arc
D. Welded portion length

30. Temperature attained in soldering of metals is about __________ C.
A. 150-300 B. 400-500
C. 650-800 D. 1000-1100

31. The normal stress is the same in all directions at a point in a fluid,
only when the fluid
A. is at rest & has zero viscosity.
B. is frictionless.
C. fluid layer has no motion relative to an adjacent layer of fluid.
D. is incompressible & frictionless.

32. A 2 kg object weighs 1.8 kgf on a spring balance. The value of 'g' at
that location in m/sec
2
is
A. 8.82 B. 9.81
C. 10.88 D. 0.95

33. In chemical dehumidification of air
A. both specific humidity & dry bulb temperature increases.
B. both specific humidity & dry bulb temperature decreases.
C. specific humidity decreases & dry bulb temperature increases.
D. specific humidity increases & dry bulb temperature decreases.

34. What is the pH of distilled water ?
A. 0 B. 1
C. 7 D. 14

35. Pick out the correct statement.
A.
Hot worked materials are subjected to annealing to remove
internal stresses.
B. Annealing of steel hardens it slightly
C. Normalising of a material induces stresses.
D.
Tempering of a material improves ductility & toughness but
reducess hardness & brittlenes.

36. Dielectric
A. is an electrical insulating material.
B. of low resistivity is preferred.
C. should have high thermal conductivity.
D. need not defy the corrosive action of chemicals.

37. Normalising of an object does not
A. refine coarse grain structure obtained during hot working.
B. improve ductility.
C. improve yield strength.
D. improve machanical properties.

38. Plasma is
A. a high temperature neutral gas.
B. nothing but ionised gas.
C. a source of steady and highest controllable pressure.
D. formed at very low temperature.

39. The machanism involved in the removal of metal in drilling operation
is by
A. compression
B. extrusion
C. shearing
D. both 'b' & 'c'

40. Thermal conductivity of a material does not depend upon its
A. mass
B. volume
C. surface area
D. all 'a', 'b' & 'c'

41. Carbon supply in pack carburising process is in the form of
A. charcoal
B. calcium carbide
C. hydrocarbon oil
D. graphite

42. Water hammer is caused in steam carrying pipelines, because of
A. partial condensation of steam.
B. vibration of the pipeline.
C. high degree of superheat of steam.
D. its exposure to torrential rain.

43. Powder metallurgy is used to produce
A.
high precision components with complex cavities and sharp
features.
B. components of large size.
C. porosity free components.
D.
components of such alloys whose constituents do not form alloys
readily.

44. Catalyst used in the catalytic converter employed in automobiles to
convert CO into CO and for complete oxidation of un-burnt
hydrocarbons is
A. nickel B. cobalt
C. vanadium D. platinum

45. For a thermodynamic system undergoing a process, which of the
following pairs best expresses the relationship similar to that
expressed by the pressure volume plot ?
A. Temperature - entropy.
B. Temperature - pressure.
C. Enthalpy - entropy.
D. Enthalpy-pressure.

46. The main constituent of bones is
A. CaF2 B. Ca3(PO4)2
C. CaCO3 D. CaCl2

47. Globular form of cementite is formed during the __________ process.
A. spherodising B. hardening
C. annealing D. normalising

48. Faraday's law of electrolysis is related to the
A. cation speed.
B. atomic number of the cation.
C. equivalent mass of the electrolyte.
D. none of these.

49. The two elements required to form substitutional solid solution
should not have
A. same crystalline structure.
B. same valancy
C. widely differing electronegativity.
D. same atomic sizes.

50. Rankine cycle comprises of two isothermal and two __________
processes.
A. isobaric
B. polytropic
C. isentropic
D. none of these



































SECTION 9
1. Coating provided on the electrodes used in the arc welding is not
expected to
A. add alloying elements.
B. prevent electrode from contamination.
C. stabilise the arc.
D. provide protective atmosphere to weld.

2. Desalination of water
A. makes it potable.
B. makes it non-potable.
C. means distillation of water.
D. none of these.

3. Viscoelastic behaviour is observed in __________ materials.
A. non-crystalline organic polymeric
B. ceramic
C. all crystalline
D. all amorphous

4. Probability of cavitation occuring becomes very high, when the local
__________ resulting in water bubbles formation, which on rupture
cause cavitation
A. pressure falls below the vapour pressure
B. pressure becomes very high
C. temperature becomes low
D. all 'a', 'b' & 'c'

5. Which of the following materials has the poorest electrical
conductivity ?
A. Carbon
B. Aluminium
C. Silver
D. Stainless steel

6. Pipelines carrying various utilities in chemical industries are
identified by their colour codes. The color of pipeline carrying steam is
A. black
B. silver grey
C. green
D. yellow

7. What is the percentage of chromium in 18-4-1 high speed steel ?
A. 1 B. 4
C. 18 D. 23

8. Preheating before welding is done to
A. make the plate softer.
B. burn oil & grease sticking to plate surfaces.
C. avoid plate distortion.
D. prevent cold cracks.

9. Thermal diffusivity of a substance is proportional to (where, k =
Thermal conductivity)
A. 1/k B. k
C. k
2
D. 1/k
2


10. Dew point temperature always gives an indication of the __________
of the moist air.
A. dryness
B. moisture content
C. coolness
D. latent heat

11. For a first order chemical reaction, the concentration of the reactant
decreases __________ with time.
A. linearly B. exponentially
C. logarithmically D. inversely

12. Air standard Otto cycle is more efficient than the diesel cycle for the
same
A. heat addition & compression ratio.
B. heat addition & pressure.
C. compression ratio & pressure.
D. cylinder dimension & rpm.

13. In case of brasses, with decreasing zinc percentage and increasing
copper percentage, its __________ increases.
A. percentage elongation
B. brinell hardness
C. tensile strength
D. all 'a' , 'b' & 'c'

14. A suitable lubricant used for watches is
A. metallic soap solution
B. grease
C. palm oil
D. hazel-nut oil

15. Out of the following __________ iron has the best capability to bear
sudden & excessive shocks.
A. white B. cast
C. wrought D. pig

16. For the irreversible reaction, Ca+ 2C = Ca C2 , H298 = - 60000 J .
mole
-1
. If a system initially containing 2 moles of calcium, 3 moles
of carbon and 1 mole of calcium carbide is allowed to react to
completion, the heat evolved at 298 K will be
A. 30000 J
B. 60000 J
C. 90000 J
D. 240000 J

17. Projection welding & stud welding is categorised as the __________
welding.
A. pressure B. thermit
C. resistance D. arc

18. The driving force for the sintering of a powder compact is
A. strain energy.
B. surface energy.
C. volume energy.
D. stacking fault energy.

19. The amount of water evaporated in kg per kg of fuel burnt in a boiler
is called the __________ of a boiler.
A. evaporative capacity
B. evaporation efficiency
C. thermal efficiency
D. steam load

20. Volumetric composition of flue gas analysed with the Orsat
apparatus is : CO2 = 12%, O2 = 8%, CO = nil, N2 = 80%. This flue gas
composition indicates that
A. pure oxygen has been used for combustion.
B. nitrogen percentage in the fuel is very high.
C. excess air has been used for combustion.
D. hydrogen is not present in the fuel.

21. A fluid is termed as the Newtonion fluid, when the shear stress is
__________ the velocity gradient.
A. independent of
B. inversely proportional to
C. directly proportional to
D. none of these

22. Transition from laminar flow to turbulent flow in fluid flow through a
pipe does not depend upon the
A. length of the pipe.
B. diameter of the pipe.
C. density of the fluid.
D. velocity of the fluid.

23. When the wet steam is throttled but still remains wet at the exit of
the throttle valve, then its temperature & dryness fraction
respectively
A. decreases & increases.
B. increases & increases.
C. increases & decreases.
D. decreases & decreases.

24. Limestone addition in the blast furnace is done to flux __________
present in the raw materials.
A. SiO2 B. Al2O3
C. MnO2 D. P

25. The 'transition temperature' for ductile to brittle behaviour of steel
increases with increase in the __________ content in steel.
A. carbon
B. manganese
C. both a & b
D. neither 'a' nor 'b'

26. The burnout heat flux in the nucleate boiling regime is not a
function of the
A. liquid density.
B. vapour density.
C. temperature difference.
D. heat of evaporation.

27. The approximate height of a blast furnace having a useful volume of
2000 m
3
is about __________ metres
A. 25 B. 35
C. 55 D. 75

28. The cathode in an electrochemical cell always carries
A. negative charge.
B. positive charge.
C. zero charge.
D. positive or negative charge depending upon the nature of the cell.

29. An oxidation process is accompanied with decrease in the
A. number of electrons.
B. oxidation number.
C. number of ions.
D. all (a), (b) & (c).

30. Hot dipping process is used for coating a low melting point metal
(e.g. Pb, Sn, Zn) on iron, steel & copper having relatively higher
melting points. Which of the following is not a hot dipping process ?
A. Galvanising
B. Tinning
C. Sheardising
D. none of these

31. Hot extrusion of aluminium is done in the temperature range of
__________ C.
A. 550-600 B. 450-500
C. 350-400 D. 250-300

32. Stellite is a __________ material.
A. ferrous
B. ceramic
C. cemented carbide
D. non ferrous cast alloy cutting tool

33. Percentage of argon (by volume) in dry atmospheric air is about
A. 0.09 B. 0.3
C. 0.57 D. 0.94

34. An abrupt and sudden fall in the readinp of barometer is an
indication of the
A. storm
B. rain
C. clear weather
D. cold wave

35. Steam condenser tubes are made of ad-mirability brass, in which
percentage of zinc & copper are __________ respectively.
A. 70 & 30
B. 30 & 70
C. 50 & 50
D. 90 & 10

36. With increase in temperature, the electrical conductivity of a
__________ decreases.
A. semi-conductor
B. metal or alloy
C. dielectric
D. none of these

37. All the atoms of the world comprise of electrons, proton & neutron
except that of __________ atom in which neutron is absent.
A. deuterium B. hydrogen
C. neon D. helium

38. Which of the following gases cause global warming ?
A. Carbon monoxide
B. Carbon dioxide
C. Nitrogen
D. Ozone

39. Multistage compression of air as compared to single stage
compression offers the advantage of
A. power saving per unit weight of air delivered.
B. moisture elimination in the inter-stage cooler.
C. increased volumetric efficiency.
D. all (a), (b) & (c).

40. Fine grained steels have
A. high brittleness
B. higher tendency to distort
C. high ductility
D. none of these

41. Dislocation cross-slip is difficult in those materials, which have
A. large number of slip systems.
B. high work hardening rate.
C. coarse grain size.
D. low stacking fault energy.

42. Shrinkage allowance on pattern is provided to compensate for
shrinkage when the
A.
metal changes from liquid state to solid state at freezing
temperature.
B.
solid phase temperature drops from freezing temperature to the
room temperature.
C.
liquid metal temperature drops from pouring temperature to room
temperature.
D.
liquid metal temperature drops from pouring temperature to
freezing temperature.

43. Spark plug is provided in a/an
A. engine having carburettor.
B. diesel engine.
C. compression ignition engine.
D. both(b) & (c).

44. Oxyacetylene reducing flame is used while carrying out welding on
A. alloy steel
B. grey cast iron
C. mild steel
D. high carbon steel

45. Nusselt number is related to the Reynolds number (Re) in turbulent
& laminar flow respectively as
A. Re
0.5
, Re
0.8

B. Re
0.8
, Re
-0.5

C. Re
0.8
, Re
0.5

D. Re
-0.8
, Re
0.5


46. Lead pencil contains
A. graphite
B. lead sulphide
C. lead
D. both(b) & (c)

47. Function of gear box is to
A. reduce the speed.
B. obtain variable speed.
C. increase the speed.
D. produce high torque.

48. Pearlite comprises of
A. 87% cementite & 13% Fe.
B. 87% ferrite & 13% cementite.
C. 93.33% ferrite & 6.67% C.
D. 87% ferrite & 13% C.

49. Which of the following if present in iron ore, enhances its value ?
A. Alumina
B. Alkali oxide
C. Lime & Magnesia
D. None of these

50. As per international norms, the maximum permissible value of noise
level in the industrial environment is __________ decibels as
measured at a distance of 1.5 metres from the source of noise.
A. 110 B. 85
C. 60 D. 45