ATV Safety

For Agricultural
Workers
2
Acknowledgements
The Farm Safety Association Inc., FSA, expresses gratitude to the Farm and Ranch
Safety And Health Association, FARSHA, of BC for granting permission to reproduct
and distribute this document. FSA have made some minor changes to make this
guide specific to Ontario.
This guide could not have been developed without the valuable assistance and input
of many organizations and individuals, including in particular, the following people
provided valuable advice and background information:
David Baker, Department of Agricultural Engineering,
University of Missouri-Columbia
Mike Blankenship, Director of Safety,
Mississippi Farm Bureau
Bill Hinde, Safety Director,
ATV/BC Quad Riders Association of BC
Dave Rowe, Forest Industry Specialist,
Workers Compensation Board of BC
Kevin Thipthorpe, Statistical Assistant,
Workers Compensation Board of BC
Some health and safety information in this booklet is based upon the resources of
the US National Ag Safety Database (NASD), as well as WorkSafe Western Australia.
The information in this booklet was originally presented as a course on ATV Safety,
prepared for the BC Logging Health and Safety Agency. These resources are
acknowledged with thanks.
The photographs in this booklet are reproduced courtesy of Sandeep Mangat
and Cheryl Pruitt, and may be reproduced with permission from FARSHA.
The drawings in this booklet are reproduced courtesy of the US National
Ag Safety Database (NASD).
This is the first edition of this booklet, revised December 2006.
3
Table Of Contents
Acknowledgements ................................................................................................ 1
Table Of Contents .................................................................................................. 2
Introduction ............................................................................................................ 3
Who is This Booklet For? ....................................................................................... 3
How to Use This Booklet ....................................................................................... 7
Current Situation of ATV Use in Ontario Agriculture .............................................. 8
Children and ATVs in Agriculture ........................................................................... 9
Whats Required? ...................................................................................................12
Whats Good Practice? .......................................................................................... 13
How to Choose an ATV ......................................................................................... 14
Special Features of the ATV .................................................................................. 16
Protective Gear ...................................................................................................... 20
Pre-Ride and Post-Ride Inspection ........................................................................ 22
Working Alone ........................................................................................................ 26
Operating the ATV .................................................................................................. 27
Conclusion ............................................................................................................. 34
Resource Information ............................................................................................. 36
4
Introduction
Since its founding in 1973, the Farm Safety Association (FSA) has worked to make
employers and workers aware of safety and health hazards, and to help them follow
Ontarios requirements. FSA also provides on-site training, literature, videos, and
other health and safety guidance.
This booklet reflects what we know about the hazards associated with ATV use,
and provides advice on safe ATV use in agriculture. It also explains the current
requirements of the Workplace Safety & Insurance Act and the Occupational
Health and Safety Act, as they apply to ATV use in Ontario agricultural operations.
As a general guide, this booklet may not cover all details of safe ATV use.
FSA assumes no responsibility or liability for the application of this information,
recognizing that circumstances, conditions, and other factors may vary greatly.
FSA welcomes your inquiries and comments on this booklet. For more information,
or to receive a catalogue of resource materials which lists all FSAs available farm
safety information, please contact:
Suite 101, 75 Farquhar Street
Guelph, ON N1H 3N4
Tel: (519) 823-5600 or toll free: 1-800-361-8855
Fax: (519) 823-8880
Email: [email protected] Web site: www.farmsafety.ca
5
Who is This Booklet For?
This booklet will be useful to every agricultural operation in Ontario that uses,
or is considering using, an all-terrain vehicle (ATV).
If you are registered with the Workplace Safety and Insurance Board (WSIB) or pay
workers as part of your farm operation, your workplace falls under the requirements
of the Workplasce Safety and iInsurance Act (WSIA) and the Occupational Health
and Safety Act (OHSA). Following the recommendations of this booklet will assist
you in meeting the current requirements of the OHSRA.
Why ATV Safety?
Rather than providing a list of statistics of ATV-related injuries and deaths, here are
some observations based on recent ATV accidents in Ontario and the rest of Canada.
The same factors show up, over and over again, in ATV accidents:
Driving on or along a highway, or crossing a highway
Carrying a passenger on the ATV
Refusing to wear a helmet
Inadequate training or supervision, especially of young people and children
Use of poorly-maintained equipment, or older, unsafe ATV models
In recent years, ATV-related deaths and serious injuries have shaken many
Ontario communities. Some have involved the use of ATVs as workplace
equipment in forestry, agriculture, and other industries. Others have taken place
during recreational activities. Many have involved young people and children. In
most cases, these deaths and injuries could have been prevented by better training,
safer procedures, or more careful equipment maintenance.
The goal of this booklet is to bring together the most reliable information on ATV
safety, and make it applicable to the special situations in Ontario agricultural
operations.
6
What is an ATV?
The information in this booklet applies to four-wheeled or quad type all-terrain
vehicles. (Other types of equipment are sometimes also called all-terrain vehicles,
particularly in other countries.) This booklet does not deal with the safe operation of
snowmobiles, dirt bikes, or riding mowers. These vehicles all have their own special
features and safety hazards, which are beyond the scope of this booklet.
At the end of this booklet, you will find a brief discussion of the four-wheeled
and six-wheeled utility vehicles that more closely resemble a small car than a
four-wheeled motorcycle. These vehicles are significantly different from ATVs
in many ways, and may be better suited to some types of agricultural tasks
than ATVs.
The first ATVs sold in North America were tricycle-type vehicles, with one wheel
in front and two in the back. Since the 1980s, three wheeled ATVs have not been
manufactured or sold in North America, because their instability made them prone
to serious rollover accidents. The organization of doctors who often treat people
injured in ATV accidents, the American Academy of Orthopedic Surgeons, has
adopted a strongly-worded resolution supporting the ban on three wheeled ATVs.
If you still have a three-wheeled ATV, FSA strongly urges you to replace it with a
safer, four wheeled model.
7
ATV stands for all-terrain vehicle. An ATV is a small, specialized piece of mobile
equipment that is designed for use on rough, unpaved ground. The operator sits
on a saddle-like seat, and steers with handlebars (unlike most other small vehicles,
which have chair or bench-type seats, and are controlled with a steering wheel).
The ATV has four large balloon-like tires, with very low air pressure.
Most important, the ATV is designed to be driver-active. On a driver-active vehicle
like an ATV (or a motorcycle or snowmobile), the operators body movements help
control the ATV. Driver-active vehicles require a strong combination of skill, good
judgement, attention, and physical strength.
8
How to Use This Booklet
This booklet explains how to safely use an ATV on your farm, ranch, or orchard.
However, this booklet cannot substitute for a good course on basic ATV operation.
These courses are inexpensive, and include hands-on experience. Many are
specially designed for young people. FARSHA strongly recommends that everyone
who may operate the ATV take one of these courses. In most regions of Ontario,
ATV training courses are regularly offered through the Ontario Federation of Al
Terrain Vehicle Clubs
With everyone properly trained in basic ATV operation, you may wish to use
this booklet as a guideline for discussions with family members, as well as hired
workers. There will certainly be topics in this booklet that you have not considered,
and you may improve some operating procedures by following the suggestions in
this booklet. When you train new workers, use this booklet as a checklist for ATV
safety procedures.
At the end of this booklet, you will find some further resource information
on ATV safety.
9
Current Situation of ATV Use in Ontario Agriculture
In Ontario, we see ATVs being used on farms, ranches, and orchards:
Herding livestock
Checking fences and irrigation lines
Hauling fuel, chemicals, salt, feed, or other supplies
Moving injured or ill small animals
Spraying fertilizers or pesticides
Plowing snow
Mowing grass and cutting brush
In many situations, the ATV operator is working in a remote corner of the property
and is working alone.
People who operate ATVs in Ontario agriculture include:
Farm owners
Members of the farm owners family (who may be children or the elderly)
Hired workers on the farm operation
ATVs are often used on family farms, where the line between work and recreation is
sometimes unclear. The ATV may have originally been bought for farm work, but is
also used by adults or children for recreation.
10
Children and ATVs in Agriculture
The guidelines for ATV use are:
Children under 12 should not use ATVs at all
(some organizations even feel the age should be 14)
Children between 12 and 16 should only use smaller ATVs with a
90cc motor, and should always drive under adult supervision
As already discussed, safely
operating an ATV requires skill,
good judgement, attention, and
physical strength. A child or young
person is developing these
qualities, but may not yet be
consistent enough to drive an ATV
without close supervision, or even
to drive an ATV at all. Children
mature physically and mentally at
different rates whats suitable for
one 13 year old may be far beyond
the strength or ability of another.
Statistics of Use
A recent Manitoba study showed the high risks facing children who use ATVs. The
survey was carried out with interviews and questionnaires at agricultural fairs and
similar events. The Injuries Manitoba Prevention of Adolescent and Childhood
Trauma (IM PACT) study surveyed over 300 Grade 6 students in 1996-1997,
and found:
42% of the children said they had ridden ATVs on public roads
26% of the children who owned ATVs said their ATVs were
three-wheeled models
More than 50% of the children said they were driving adult sized ATVs
Only 30% of the children said they always wear a helmet while riding
We can assume that similar results would be found among children and young
people in farm families in Ontario.
11
In a policy reaffirmed in January 2000, the Canadian Pediatric Society
(the organization of doctors who treat children), recognized ATVs (two-, three-,
and four-wheeled) as hazards to the health of Canadian children. Based on their
experience treating children injured in ATV accidents, they called for:
A ban on ATV use by children under 14 years, since the safe use
of off-road vehicles requires skill, judgement, and experience
Compulsory licensing of all ATV operators
A ban on passengers on ATVs
Compulsory use of helmets during ATV use
The North American Guidelines for Childrens
Agricultural Tasks
The Canadian Coalition for Agricultural Safety and Rural Health has recommended
that farm parents follow the North American Guidelines for Childrens Agricultural
Tasks (NAGCAT) when giving farm chores to children and young people.
The NAGCAT guidelines on ATV safety for children ask the following questions:
1. Can the child reach and operate all controls while comfortably seated?
2. Is the child strong enough to operate the controls without straining?
3. Does the child have good peripheral vision? For example, while looking
straight ahead, can the child see your finger entering his or her field of
vision at shoulder level?
4. Can the child use hands and feet at the same time?
For example, can the child run and dribble a basketball?
5. Can the child understand and repeat from memory a five-step process?
6. Can the child recognize a hazard and solve the problem without
getting upset?
7. Can the child react quickly?
8. Does the child do things that seem dangerous for the thrill of it?
9. Is your child responsible? Do you trust your child to do whats
expected without anyone checking?
10. Does the child usually go with his or her gut feeling without
thinking too much about what could happen next?
11. Has an adult demonstrated farmwork with an ATV on site?
12
12. Has the child shown that he or she can do the job safely
four to five times under close supervision?
13. Can an adult supervise as recommended?
Your answer to each question should be a definite and confident yes
(except for questions 8 and 10, which should be no). Even if your child is old
enough, you may decide, based on these questions, that she or he is not yet
ready to safely drive an ATV.
Adequate supervision of children and young people should follow these steps:
Explain the task, and draw attention to each hazard and possible problem.
Discuss solutions for each hazard and problem.
Demonstrate the task while describing each step.
Have the child or young person do the task four or five times under direct
and continuous supervision.
Have the child or young person do the task, but come back to observe or
check every 15 to 30 minutes.
13
Whats Required?
Currently in Ontario, there are two distinct areas of requirements that apply to
ATV use. One area involves licensing, and where the ATV can be operated
(the Motor Vehicle Act, Highway Act, and so on). The other area involves the
use of the ATV as work related equipment (the requirements of the Occupational
Health and Safety Act).
14
Whats Good Practice?
Good practice (sometimes called best practice) goes beyond the minimum
legal requirements. For instance, family members who are not considered farm
employees are not regulated by the requirements of the Workplace Safety and
Insurance Act and Occupational Health and Safety Act.
However, a good practice would be to make a rule that on your property,
everyone who operates the ATV must always follow the guidelines in this booklet.
15
How to Choose an ATV
ATVs can be very different. When using any new or unfamiliar ATV, check
the manufacturers manual to prepare yourself for the different features.
This section is not intended to be a buyers guide to ATV manufacturers and models.
However, by considering the following list of pointers, you may get a clearer idea of
the types of ATV available on the market. If you are planning to buy an ATV, this list
should help you make a good choice.
At the same time that you buy the ATV, be sure to include a suitable helmet,
if you do not already have one in good condition.
If you think someone may be tempted to carry a passenger on your ATV, you
should consider a different type of equipment. Some manufacturers are now
making four-wheeled and six-wheeled vehicles that can safely carry one or more
passengers and a larger load of gear or farm materials. Some of these vehicles
are equipped with roll bars or rollover protective structures (ROPS). At the end of
this booklet, you will find a brief discussion of the advantages and disadvantages
of this type of vehicle.
ATVs can be designed for serious work or for recreation be sure to buy
the utility model, which will be more heavy-duty and durable.
Does it have a four-stroke or two-stroke engine?
(Utility models almost always have four-stroke engines.)
Does it have two-wheel drive or four-wheel drive?
(Utility models almost always have four-wheel drive capability.)
Does it have a rear differential, and if so, can it be locked and
unlocked according to need? (Utility models offer the flexibility
of a lockable differential.)
Does it have an independent suspension system?
Is it designed for work in the bush, with brush shields
to protect the operators legs?
Is the transmission standard, automatic, or semi-automatic?
(Utility ATVs should have a reverse gear, and automatic clutch.)
Is the starter electric (with a battery) or recoil (with a pull-start)?
16
Does the ATV have options or special attachments,
like a trailer hitch or a winch?
Consider who will be using the ATV are the size proportions comfortable
for the operator(s)?
Can you comfortably push the foot brakes?
Can you comfortably stand, with enough clearance from the seat?
(On rough ground, a half-standing position is how you will absorb
shocks and avoid getting thrown.)
Are the handlebars positioned so your arms are slightly angled
(not stretched right out)?
Can you comfortably grip the handlebar controls?
Are the footplates solid and non-slip, and comfortably positioned?
Do they have a raised ridge to prevent the foot from slipping off the edge?
Is there space for your knees without banging against the handlebars or
brush shields?
Are you able to swing your right leg high over the seat, to get on and off
the ATV? (If this is not comfortable, you should look into an ATV model
with a cutaway space in front of the seat.)
If there is any possibility that children will use the ATV, it must be a smaller model
with a 90cc motor. The helmet must be fitted to the childs head size.
17
Special Features of the ATV
In many ways, ATVs are very different from any other kind of vehicle you might drive.
The special features of the ATV help explain some of the serious safety hazards, so
understanding them will make you a safer ATV operator. You will also be able to use
this information when explaining ATV safety to others on your operation. The special
features are:
Large low-pressure tires
A high center of gravity
Fixed rear axle
Limited protection for the operator
The Tires
The ATVs big balloon-type tires are designed to be very good on rough terrain.
On the other hand, they are very bad on pavement. Like driving a truck with
under-inflated tires, they affect the steering. In part, this is why it is not legal to
drive an ATV on a highway. In addition, the tires create a much more bouncy ride
than other vehicles, which adds to the instability by exaggerating the ups and downs.
The tires are intended to have very low air pressure. The manufacturers manual
will say exactly, but its usually between 2 and 6 pounds per square inch (psi),
which is much lower than the 35 to 40 psi required by most vehicle tires. With
such low pressure, a regular tire gauge is not accurate enough, so a special
smaller-scale gauge will be supplied with the ATV. Always use the right gauge.
On ATV tires, even the difference of 1 psi will make a difference. The tire pressure
must be the same on all four tires. If its not, the ATV will pull towards the soft tire.
Always check the tire pressure before each ride, and top up the air if its low.
The High Center of Gravity
All vehicles have a point called the center of gravity, which is the point where all
parts of the vehicle balance each other in all directions. In addition, all vehicles have
an imaginary boundary at ground level, usually a square or a triangle, called the
stability baseline. If the center of gravity moves outside the boundary of the stability
18
baseline, the vehicle will tip and roll over.
Where are these located on an ATV?
Each ATV model is a little different. But in general, the center of gravity
of a parked ATV can be estimated:
about six or more inches above the center of the axle
about six or more inches rear of the halfway point between the two axles.
The stability baseline can be estimated
by imagining the point where each wheel
touches the ground, and drawing a line
through each of those four points, to
form a square.
The center of gravity of the ATV itself
stays the same. But if you add other
weights to the ATV (the body weight
of an operator, and heavy gear on the
carrier racks), the center of gravity
includes those weights, too. The new center of gravity is higher, and it may also be
further forward or backward, or off to one side. The typical utility model ATV weighs
about 600 pounds by itself, so the additional 200 pounds of an operator and gear
can significantly raise the center of gravity. (Lightweight recreational ATV models
that advertise a high ground clearance will, of course, have an even higher center
of gravity.)
Therefore, when the ATV is fully loaded, travelling across a slope, the center of
gravity is dangerously close to the stability baseline. In this situation, running over
a bump may be enough to cause a rollover.
Or, in another example, consider what happens to the stability baseline when
the ATV makes a sharp turn. The four points of wheel contact with the ground no
longer form a square they become more like a triangle. If the ATV is then loaded
with gear over the front axle, the center of gravity is higher and further forward.
When the front wheels are sharply turned, the stability baseline at the vehicles
front end is dangerously narrow so narrow that the center of gravity can easily
move outside the boundary of the stability baseline. The result will be a rollover.
19
When you explain to family members or employees why they should never carry a
passenger on a single-operator ATV, be sure to point out that the vehicles center of
gravity is already high enough with just the operators body weight. The addition of
a passenger makes an ATV dangerously unstable.
The Fixed Rear Axle
Most ATVs have a fixed or solid rear axle. This is a significant difference from other
vehicles, which use a differential mechanism to allow the two wheels to turn at a
different rate when going around a curve.
When the ATV comes to a curve, you steer the handlebars, and the front wheels
turn in the direction of the curve. But both back wheels, because the ATV has no
differential, want to keep going straight. Therefore, when you turn, the force is
pulling the ATV out of the curve. The whole ATV tries to skid outwards, or roll
over away from the curve. This is more noticeable at higher speeds.
The safe operation of the driver-active ATV depends on your body movement.
To overcome the outward roll of the ATV, you must shift your upper body into the
direction of the curve. In effect, this brings the center of gravity back inside the
stability baseline. And to overcome the straight-ahead movement of the rear wheels,
you must force the inner rear wheel to slip a little more than the outer rear wheel.
This happens when you brace your outer foot hard on the footpeg as your upper
body leans inwards.
Of course, these movements are affected by the distribution of the load on the
ATV. An unevenly distributed load makes the ATV much more difficult to control.
The operators movements are another reason why you should never carry
a passenger (unless the ATV is specially designed for one). The long seat
on an ATV is intended to allow the operator to move freely, and play a
driver-active role in controlling the vehicle. Carrying a passenger would
interfere with this necessary movement.
20
Very Little Operator Protection
Most workplace vehicles have some kind of built-in protection for the operator:
it may be the reinforced cab of a truck, or the rollover protective structure (ROPS)
of a tractor or heavy equipment. The ATV has nothing of the kind. There is no ROPS
on an ATV, no cab, and very little shielding.
What keeps the operator safe is a combination of preventive measures (good
operating skill, and well-maintained equipment), and if something goes wrong,
protective gear and clothing.
Even in a simple upset on rough ground, you can suffer cuts, puncture injuries,
and broken bones. In a rollover, you may be pinned under the machine. In any
kind of ATV accident, there will not be time to protect your head, if youre not
already wearing a helmet.
Head injuries in ATV accidents are serious. Operators have been struck by
falling rocks, by low-hanging brush, or have been thrown to the ground.
Wearing a helmet will not prevent the accident itself. However, the helmet can
make the difference between a fatal head injury and survival after the accident.
Or, the helmet can make the difference between a permanent brain injury and
recovery from a less-serious head injury. This choice is in your hands every time
you ride the ATV.
21
Protective Gear
Wear the best protective gear possible whenever you use the ATV. You are
setting an important example for everyone who sees you, especially the
members of your own family.
When using the ATV in a workplace,
the operator must wear:
the right headgear and
eye protection
suitable clothing for
the environment
gloves, long pants and
long sleeves
Its important to remember that even
though the moving parts of the ATV are
covered, a loose bootlace or piece of
clothing can be entangled and cause a
severe injury. This type of entanglement
injury is similar to the PTO (power take-off)
entanglement that most farmers have
heard of. A loose bootlace that gets drawn
into a spinning ATV axle or belt can pull
your leg with enough force to break it.
Loose clothing can also get caught in
passing brush, and drag you from the
moving ATV.
The Helmet
The correct type of helmet can make a difference between life or death - or between
a concussion or a permanent brain injury. It is also one of the legal requirements of
ATV use.
The helmet must be certified for ATV use. It must be the right kind not a bicycle
helmet, not a hockey helmet, not an industrial hard hat. An ATV helmet will stay on
22
your head through anything. It has a chin strap and visor or goggles. It will protect
your face and eyes from loose gravel, dust, bugs, and branches.
It should have a certification sticker from one of the following agencies:
Snell Memorial Foundation, for motorcycle use
Canadian Standards Association (CAN3-D230-M85),
for motor vehicle applications
British Safety Institution (BS5361), for vehicle users
US DOT (571.218), for motorcycle helmets
The helmet should be in good condition, with no
cracks or gouges in the plastic. The inner foam
padding should be in good shape, and the
chinstrap must work. The visor or goggles
should be clear and not scratched or clouded.
If the ATV operator is a child or young person,
the helmet must be carefully fitted for the
smaller head size.
If the helmet goes through an accident or is somehow damaged:
Thank it for its service, and get rid of it.
Dont use it again. It cannot protect you any more. Get a new one.
Clothing
Suitable clothing will protect you from many minor injuries on an ATV. Suitable
clothing can also make safe operation easier. Leather gloves will protect your hands,
as well as keeping them warm and dry. Many of the ATV controls are handled with
your thumb and fingers, so having cold, stiff hands will make it harder to drive safely.
Boots
Your feet are an important part of how you control the ATV by shifting your body
when turning, half-standing over bumps, and so on. The soles of your boots should
be non-slippery, because you brace your weight on the ATV footplates. Your feet
and lower legs may be hit by gravel or branches as you drive, so high sturdy boots
will protect you.
23
Pre-Ride and Post-Ride Inspection
ATVs take a lot of wear and tear. Things break down, or shake out of adjustment.
ATVs need frequent and regular maintenance. The pre ride and post ride inspections
are your chance to identify and correct small problems while they are still small.
Reporting Mechanical Defects and Safety Problems
Even on a small operation, you should have a clear system for reporting and
correcting health and safety problems. In fact, one of the WCBs requirements
is that anyone who sees an unsafe condition or act must report it to a supervisor
or to the employer. In turn, the person who receives the report must investigate
the situation and correct any hazard without delay.
A good way of doing this with your ATV is by using a tag system. A notice or tag
at the ATVs ignition warns the next user either:
That the ATV has a serious safety problem, and that it cannot be
operated at all, until the problem has been fixed, or
That the ATV has a safety problem, and that it can be used only
in certain circumstances
For example, if the ATVs brakes arent working, the tag should say clearly that no
one may use the ATV at all, until the brakes have been fixed. On the other hand,
if the ATVs headlights arent working, the tag should say that the ATV may be
operated only on private land during daylight hours, until the lights have been fixed.
A tag system of this kind eliminates confusion, and cannot be overlooked.
In addition, each ATV in the workplace
should have a file of maintenance records
or a logbook. Each time the ATV is inspected,
and each time the ATV has any repairs or
problems, these should be noted. These
records may be needed if you ever have
to show evidence of regular maintenance
and care.
24
The Pre-Ride Inspection
The manufacturers manual will have a list of what to check, and how often.
Always make sure that you are looking for everything thats covered in the
manufacturers manual.
The pre-ride inspection takes place in two parts before you turn it on,
and when its running.
With the ATV turned off, check the following:
Is the manufacturers manual there?
Look at the maintenance records are there any
recent problems or warnings?
Is the gas tank full?
Is the oil level okay?
Is the tire pressure on all four tires okay?
Is the helmet in good condition? Does the chinstrap work?
Is the visor clear and unscratched?
Are the first aid and emergency kits there? Is the tire repair kit there?
Grab each tire with both hands and try to rock it there
should be no movement or play.
Grab each footpeg and footplate and try to move it there
should be no movement or looseness.
Are all the wheel bolts tight on each tire?
Look at all four tires, all around there should
be no obvious worn places or cuts.
Look at all the cables and lines there should be
no signs of wear or breaks.
Now start the ignition.
Do the lights come on?
Turn the handlebars as far as they go the throttle should
continue to run smoothly, regardless of the handlebar position.
On level ground, go slowly. Try the brakes. You should have a
smooth stop, with no grabbing, and no pulling to one side.
25
Now turn the ignition off.
Does the engine stop smoothly? There should be no run on.
Get in the habit of looking around the whole ATV before starting up, every time.
Check that nothing is dragging, and that nothing is entangled in the wheels or
axles. Check that the tires are okay. Check that no one is standing too close.
Finally, make your inspection entry in the logbook. Initial and date it. Say either
that everything was okay, or specify the problem and what was done to correct it.
Post-Ride Inspection
Serious ATVers have learned from experience to always do a post
ride inspection before putting the ATV away.
If you did not check the ATV before putting it away, and something was loose or had
been damaged, when would it be discovered? Someone might discover the problem
in the next pre-ride inspection, when they might be tempted to ignore it, since theyd
be eager to get going.
The post-ride inspection has some of the same points as the pre ride inspection
and some different. Check:
All the fluid levels (gas, oil, and so on) and top them all up.
The pressure and condition of all four tires, and add air if necessary.
The tightness of all important parts the footpegs and footplates,
the wheels, the wheel bolts should show no looseness or play.
Tighten any that need it.
All lines and cables there should be no signs of wear or damage.
26
Clean the ATV thoroughly. Grit and standing water will corrode and damage
important parts.
Inspect the helmet for any signs of wear or damage, and replace it if you have any
question about its effectiveness. Replace anything that was used in the first aid or
emergency kits.
Preventive Maintenance
Many farm operations do their own maintenance. Theres sometimes a temptation
to modify the equipment. Dont. If the ATV is still under warranty, take it to the dealer
for modifications, or you may lose the warranty. If you want modifications to the ATV
extra gear racks, higher clearance, a trailer hitch, or something else get the
modifications done properly by the authorized dealer. If someone on your operation
modifies the ATV, it may then become your liability.
Emergency Maintenance
There is no spare tire on an ATV. You should always carry a repair kit to use if the tire
goes flat. The repair kit should include a pump or a canister of compressed air, and a
repair kit (plugs), plus directions for how to use them.
Check the manufacturers manual for the emergency starting procedure. An ATV
that uses a battery starter will not start if the battery fails. Usually, this type of ATV will
have an emergency recoil starter. On a few ATV models, the gear shifter depends on
battery power, so the manufacturer makes an insertable bypass for manually shifting.
If this is your type of ATV, make sure this part and instructions are kept with the ATV
at all times.
27
Working Alone
Because the ATV should not be used to carry a passenger, you may find yourself
working alone on a distant corner of the farm property. Does this work pose the risk
of a disabling injury? Could someone be unable to get help if they were injured? In
agricultural situations, the answer to these questions is almost always yes.
One suggestion for agricultural workplaces is that in this type of situation, the
employer must have a way of periodically checking on the well-being of the
person working alone.
A two-way radio or cellphone is a good first step. But if you rolled the ATV and
could not make a call for help how long would it be before someone started
looking for you?
Make an emergency plan for this kind of situation, and discuss it with everyone
involved with your operation. Always make sure that someone else understands
where you have gone, what route you are taking, and when you plan to return.
Arrange to have a reliable person call you regularly then, if you do not answer
the call, they can send help without delay.
Equip the ATV with a first aid kit. At the end of this booklet, theres a list of what it
should contain. Consider what other emergency equipment should be carried on the
ATV: flares, a space blanket, matches, some basic tools and spare parts, and so on.
Emergency Evacuation
Emergency evacuation is also something you should plan for. Usually, an ATV
is used because of difficult terrain; in this situation, a conventional ambulance
would probably not be able to evacuate someone injured in a serious ATV accident.
The emergency response agency in your local area (a volunteer fire department,
an emergency service, or a police detachment) can help you work out an
emergency plan.
28
Operating the ATV
Of course, the best way to learn to operate an ATV is by doing it. This booklet is
no substitute for a hands-on course in basic ATV operation. The courses offered
in Ontario on basic ATV operation will cover all of these topics in detail. However,
here are some pointers for safely operating an ATV.
Starting Up
Some models of ATV have different starting procedures, so follow the directions
in the manufacturers manual. Make sure the ATV is in neutral before starting.
The parking brake should be engaged if the ATV was properly parked from the
previous use.
On Normal Rough Terrain
Walk a new or tricky route first, asking yourself questions like:
How stable is the ground?
How loose are the rocks?
How deep are the holes?
Are there low-hanging branches?
Is there space to safely turn around?
Experienced ATVers always look ahead
when driving. Its important to plan for the
terrain before you get to it, rather than
reacting at the last minute.
One basic rule that seems obvious, is dont go faster than you can see to stop.
There may be other vehicles around and the ATV operator will come out the worst
in a collision with another vehicle or piece of equipment. There may be branches or a
tree down, or an animal on the road. Low-hanging branches are a special hazard. A
helmet may save you from a brain injury, but if youre going too fast, a collision with a
branch may throw you from the ATV completely. If youre ATVing in a group, keep a
safe distance from each other.
29
Dont ever drag your foot on or even near the ground while the ATV is moving.
This may seem obvious, but ATV operators have had a foot and ankle caught
and twisted between the footplate and the ground. This usually happens while
getting on or off a rolling ATV, or in the panic of getting off a tipping or sliding ATV.
Make it a habit never drag your foot on or near the ground.
Another pointer that might seem obvious is: never ride the ATV while reversing
down a slope either the ground, or a loading ramp. Its just too easy to lose
control, and with the ATV rolling backward, you will not have the chance to get off.
Dont suddenly throttle up (give it gas) or rev the motor. This can be enough to
start a back-flip.
Through Water
Always check the manufacturers manual before driving through water. The depth
limit will be different from one ATV to the next. Then walk the route first with a stick
to check for hidden holes, or a soft muddy bottom. Drive through the water at a
steady speed, but do not raise a big spray.
Once out of the water, dont count on the brakes until youve checked them.
Dont ever try to drive through fast-moving or unfamiliar water.
Reversing
Almost all ATVs have a reverse gear now. They have no mirror and no backup
beeper. Rarely, you may need to back the ATV up but, if you do, always watch
closely behind you.
Going Uphill
When driving the ATV up a slope, remember that the center of gravity will want to pull
towards a back-flip. To counteract this force, make adjustments before you start going
uphill:
Redistribute the load so more weight is on the front of the ATV.
Slide forward on the seat, and lean forward and down.
Gear down, and slow down. Always climb a hill in low gear.
30
Dont make changes in the traction between
the wheels and the ground by suddenly turning
the front wheels, popping the clutch, or revving
the throttle. If you picture the ATV driving uphill,
you can see that a sudden burst of power will
rotate the rear tires faster than the vehicles
weight can be pushed forward. The ATV will
pivot on the back axle and flip over, pinning
the operator underneath.
Some ATV advertisements make it look like these vehicles can climb almost
straight up a steep slope. Remember that these advertisements are filmed
under ideal conditions, with extreme camera angles, and highly skilled stunt
riders. Dont overestimate the capacity of your ATV or your own skill and experience.
If the slope is too steep, the ATV will begin to stall out or roll or slide backward. If
you panic and slam on the brakes, the back axle may lock. In this situation, too,
the ATV can pivot on the back axle and flip over, pinning the operator underneath.
What should you do if you discover the slope is too steep?
Apply first the front and then the rear brakes, with the ATV pointed uphill.
If it keeps sliding, get off and step away. You wont be able to try and
stop a 600-pound ATV by force, anyway.
If the front and rear brakes are holding, carefully get off the ATV,
while continuing to apply the brakes.
Stand with your feet clear, and set the parking brake, put the ATV
into neutral, and turn the engine off.
Then, with the immediate situation taken care of, you can decide
what to do next: get help, use a winch, or try to walk it down.
Going Downhill
When driving the ATV down a slope, the center of gravity will want to pull
towards flipping forward. To counteract this force, make adjustments before
you start going downhill:
Redistribute the load so more weight is on the back of the ATV.
Slide back on the seat, and try not to lean forward.
31
Gear down, and slow down. Do not use neutral. Let the engine
keep you slow.
If you must use the brakes, use the rear brakes.
And brake gently, never suddenly. Dont ride the
brakes. You can picture what happens when an
ATV is speeding downhill, and the front brakes
are suddenly applied. The front axle locks too
quickly to stop the built-up momentum of the
ATV and operator. The ATV pivots on the front
axle and flips forward, and the operator is either
thrown forward or pinned underneath the ATV.
Even a sudden, sharp application of the rear brakes can cause an upset, if the rear
wheels lock. If the rear wheels lock too quickly to stop the forward movement of the
ATV, the back end of the vehicle will drag sideways and the ATV may roll.
Going Sideways Across a Slope
Avoid going across a slope, whenever you can. The ATV is
very unstable in this situation. Never cross a slope with a
loose surface or big bumps.
Even on a gentle angle, the center of gravity will pull
towards the downhill side of the slope. Stop and
redistribute the load to the uphill side of the ATV.
Keep your body weight shifted to the uphill side, too.
Stay on the inside of the road or trail, because the outer edge of the trail may be
loose or crumbling, too.
Avoid the bumps and holes, and go slowly. Tipping one side of the ATV by
running over a bump can be enough to cause a rollover.
If youre on a slope, and you feel the ATV starting to roll over:
Try to turn the wheels more to the downhill, if the terrain
makes this possible.
32
If you cant, carefully get off the ATV on the uphill side. The ATV may then
level itself out without your body weight adding to the high center of gravity.
Once off the ATV, youll be able to think through what to do next.
Driving Through Curves
On an ATV, you cannot take a curve at the same speed as driving in a straight line.
Slow down before the curve. If you apply the brakes during a curve, the wheels will
tend to skid.
Steer the handlebars, firmly brace the foot on the outside of the curve, and lean into
the curve. This will counteract the force pulling the ATV outward to a skid or roll.
If youre already turning, and you feel the ATV start to roll outwards:
Lean your body further into the turn,
away from the direction that the ATV
is tipping.
Reduce the throttle gradually.
Straighten the wheels gradually,
to widen the turn.
Parking
Always park on level ground, if at all possible. If there is no level ground,
park crossways to the slope.
Always use the parking brake. If youre parking on a slope, use wheel chocks too,
if necessary.
Carrying Loads on an ATV
ATVs are mainly designed for transport rather than hauling large amounts of
gear. There are limits on the weight you can safely haul with an ATV. Check the
manufacturers manual for the exact limits, since they are different for each ATV
model. The manufacturers recommended hauling limit is important, but always
remember that the ATV will be harder to handle and stop with any heavy load.
Almost all ATVs have two carrier racks, on the front and back of the vehicle.
Dont try to carry gear anywhere but the manufacturers carriers.
33
An extra load on the front makes the steering more sluggish. It reduces traction on
the rear wheels, so its easier to skid the rear end and lose control. A heavy front
load also changes the side-to-side stability of the ATV you have to go slower,
to compensate.
A heavy load on the back of the ATV increases the risk of a back flip. It, too,
changes the side-to-side stability of the ATV.
Put any load as near the center of the ATV as possible, and dont let any weight
extend over the edges of the carrier racks. Use tie downs, to keep the load from
shifting while youre driving. Distribute the load evenly, front and back, and on both
sides. Use ballast, if necessary, to make sure the load is balanced.
Remember that a high or bulky load on the rear carrier will get in the way
as you swing your leg over the seat when getting on or off the ATV.
Big containers of liquids can slosh a lot of weight back and forth, high up on the ATV.
They make an ATV very unstable. If you regularly carry big containers of liquids, get
a proper carrying tank, mounted low on an ATV trailer. (A proper tank has baffles
inside, to reduce the movement of the liquid.)
Towing with the ATV
The manufacturers manual will have specific information about towing a trailer
with your ATV.
Never try to tow another vehicle or a trailer by attaching a rope or cable to the
carrier rack. This will bring the center of gravity very high, near the rear stability
baseline. It can cause the ATV to flip backwards. Only attach to the trailer hitch.
Using Ramps to Load and Unload an ATV
An ATV can be moved from place to place on a trailer or in the box of a full-sized
pickup truck. This increases the flexibility of your ATV, allowing you to move the ATV
to places that are accessible only by public roads and highways (where you cannot
drive the ATV itself).
The ramps must have a non-slip surface, and they must be securely attached to the
truck or trailer. They should, of course, be sturdy enough to support the weight of the
34
ATV and rider, and wide enough for the ATVs tires.
When loading the ATV onto a trailer or truck, position the ramps for the ATVs tires,
and secure the ramps with hooks and safety straps. Centre the ATV at the ramps,
and drive slowly up the ramps onto the trailer or truck. Apply the parking brake and
wheel chocks. Always secure the ATV by tying it down, before driving off.
When unloading the ATV from a trailer or truck, position the ramps for the ATVs tires,
and secure the ramps with hooks and safety straps. Never ride the ATV backwards
down the ramps. If a wheel starts to go off the ramp, you will not be able to jump off
the ATV as it tips over. From a standing position, with your hands on the handlebar
controls, roll the ATV backwards to the beginning of the slope of the ramps. Step
down onto the ground alongside the ramp, and with your hands on the handlebar
controls, continue to roll the ATV down along the ramps to the ground.
35
Conclusion
The most important ideas of this booklet are:
Make sure anyone using an ATV under your responsibility has
been properly trained in basic ATV operation and safety.
Do not allow passengers on the ATV.
Always wear an ATV helmet.
Do not use a three-wheeled ATV.
Never drive on or across a highway, unless you have a permit.
If your operation is covered by the requirements of the OHSA, you are
responsible for providing worker training, and assessing each persons
competence before authorizing a worker to operate the ATV.
In any case, anyone who operates an ATV on your property or on your behalf
(whether worker, family member, or guest), should be properly trained. The ATV
is a vehicle that requires a strong combination of skill, good judgement, attention,
and physical strength. Someone who does not have this combination of qualities
is at serious risk.
This booklet has explained in detail why you should not allow passengers on the
ATV. The ATV is a rider-active vehicle, and the operator needs to be able to move
freely on the ATV seat to control the vehicle; a passenger interferes with that
movement. A passenger raises the ATVs already-high center of gravity to a
dangerous level. A passenger may affect the vehicles center of gravity in other
ways as well, by adding greater instability to the front or rear axle. A passenger
will be in the way if the operator needs to get off the ATV quickly in an emergency.
(There are very few ATV models that are designed for a second person all others
are single-operator vehicles.)
In an ATV accident, the helmet may be the only thing between the operator
and a disastrous head injury or death. In almost every recorded ATV accident,
the outcome could have been different if the operator had been wearing a helmet.
By now, the evidence is clear: three-wheeled ATVs are far more unsafe and
unreliable than the four-wheeled models. The accident and injury statistics are
36
unmistakable. However, three-wheeled ATVs are still being used, especially by
children and young people on family farms. If you still have a three-wheeled
ATV, FARSHA strongly urges you to replace it with a safer, four-wheeled model.
Many of the most serious ATV accidents have been collisions with other vehicles.
In a collision between an ATV and a car or truck, the ATV operator loses. Driving
on or crossing a public road or highway is dangerous; thats why in most cases
it is illegal. In BC, any use of an ATV on or close to a highway must be done
under the terms of a special permit. If your work requires you to cross or drive
along a highway, contact your municipality or local police for a permit.
The Farm Safety Association and other farm safety organizations are very concerned
about the high numbers of serious ATV accidents in agricultural operations.
FSA Regional Safety Coordinators are available, to provide advice and information
on ATV safety, as well as other aspects of farm safety.
37
Resource Information
Where to Get More Information on ATVs
In Ontario, the Ontario Federation of All-Terrain Vehicle Clubs organizes
recreational ATV activities all over the province, including classes.
Their website address is: www.ofatv.org
The Canada Safety Council offers courses in ATV operation for adults and
children (the CSC sponsors a full range of community safety programs).
Their website address is: www.safety-council.org/training/ATV/atv.htm
The ATV Safety Institute (ASI) is an industry organization sponsored by
the ATV manufacturers to promote the safe use of ATVs. The ASI produces
videos and booklets on ATV use. Their website features an interactive ATV
safety exercise that is especially aimed at children interested in ATVing.
The website address is: www.atvsafety.org
The Canadian Agricultural Safety Association (CASA) is a coalition of farm safety
agencies from across Canada. CASA administers the Canadian Agricultural Safety
Program, and sponsors annual Canadian Farm Safety and Health conferences.
The website address is: www.casa-acsa.ca
For any other health and safety questions and information, contact:
Farm Safety Association (FSA)
Suite 101, 75 Farquhar Street
Guelph, ON N1H 3N4
Tel: (519) 823-5600 or toll free: 1-800-361-8855
Fax: (519) 823-8880
email: [email protected]
web site: www.farmsafety.ca
38
Other Types of Small Utility Vehicles
Now that youve read this booklet, you know that the special characteristics
of the driver-active ATV make it unsuitable for some types of farm work.
You should consider other types of small utility vehicles if:
You frequently need to haul bulky or heavy loads
You frequently need to haul unstable loads, such as
large containers of liquid, or live animals
You want to carry passengers
Some people on your operation do not have necessary combination
of skill, judgement, attention, and physical strength to drive an ATV.
In recent years, some manufacturers have created small utility vehicles that are
almost as versatile as the ATV, but are significantly different from ATVs in many
ways. One of these vehicles may be better-suited to your needs.
These vehicles do not demand the same level of skill and physical strength
as the driver-active ATV. They have different handling characteristics.
In general, these vehicles have a wider and more stable wheelbase. They have a
very large rear cargo area that is designed for heavy and bulky loads. They more
closely resemble a car, with a steering wheel, pedals, gearshift, and front dash
panel, and they have separate seats for a driver and passenger. Many of these
vehicles have a rollbar, and therefore also have seatbelts. These vehicles are
available as four wheeled or six-wheeled models, and have excellent traction
for heavy work.
As with all other agricultural equipment, you will get the best results by using
the most appropriate tools for the job. Consider carefully what you expect from
a utility vehicle, and make the safest choices possible.
39
First Aid Kits
FSA strongly recommends that you keep a Basic First Aid on the ATV at all times.
Use a container that can readily be taken to the scene of an injury, and that will
keep items clean and dry. Heres a minimum list of what it should contain:
QUANTITY ITEM
12 14 cm x 19 cm wound cleansing towelettes, individually packaged
30 Hand cleansing towelettes, individually packaged
50 Sterile adhesive dressings, assorted sizes, individually packaged
6 10 cm x 10 cm sterile gauze dressings, individually packaged
2 10 cm x 16.5 cm sterile pressure dressings with crepe ties
2 20 cm x 25 cm sterile abdominal dressings, individually packaged
4 Cotton triangular bandages, minimum length of base 1.25 m
2 Safety pins
1 14 cm stainless steel bandage scissors
1 11.5 cm stainless steel sliver forceps
6 Cotton tip applicators
1 2.5 cm x 4.5 m adhesive tape
1 7.5 cm x 4.5 m crepe roller bandage
1 Pocket mask with a one-way valve (a pocket mask is
only required if the person is trained in its use)
6 Pairs of latex or waterproof gloves
1 Instruction card advising workers to report any injury to the
employer for entry into the first aid records, and instructions
on how the worker is to call for assistance.
40
41
42
Farm Safety Association
Suite 101, 75 Farquhar Street
Guelph, ON N1H 3N4
Tel: (519) 823-5600
Toll free: 1-800-361-8855
Fax: (519) 823-8880
email: [email protected]
web site: www.farmsafety.ca