PLC Connection Manual
Uploaded by
bathivinodPLC Connection Manual
Uploaded by
bathivinodPLC Connection Guide
AIBUS ........................................................................................................................................ 5
Allen-Bradley CompactLogix / FlexLogix ................................................................................ 8
Allen-Bradley DF1 ................................................................................................................... 12
Allen-Bradley DF1 BCC .......................................................................................................... 14
Allen-Bradley DH485 .............................................................................................................. 16
Allen-Bradley EtherNet/IP CompactLogix .............................................................................. 19
Allen-Bradley EtherNet/IP (DF1) ............................................................................................ 22
Allen Bradley EtherNet/IP-Tag (CompactLogix/ControlLogix) ............................................. 25
Allen Bradley PLC5 ................................................................................................................. 29
Altus ALNET-I ........................................................................................................................ 32
Baumuller Servo....................................................................................................................... 34
Cimon CM1-CP4A................................................................................................................... 36
Cimon CM1-SC02A................................................................................................................. 38
Copley Controls ....................................................................................................................... 40
CROUZET M3 (FBD) ............................................................................................................. 42
CROUZET M3 (LAD) ............................................................................................................. 44
Danfoss ECL Apex20 Controller ............................................................................................. 46
Danfoss FC series ..................................................................................................................... 48
Danfoss VLT2800 Series ......................................................................................................... 50
DELTA DVP ............................................................................................................................ 52
EMERSON PLC EC20 ............................................................................................................ 54
FATEK FB series ..................................................................................................................... 56
Fuji NB Series PLC .................................................................................................................. 59
GE Fanuc CMM ....................................................................................................................... 61
GE Fanuc SNP-X ..................................................................................................................... 64
GE Fanuc Series 90-30 (Ethernet) ........................................................................................... 67
HAN YOUNG .......................................................................................................................... 70
Heng Yuan Sensor.................................................................................................................... 71
HITACHI EH-SIO ................................................................................................................... 73
HITACHI EHV ........................................................................................................................ 76
HITACHI H series (CPU port) ................................................................................................ 78
HUST H4X............................................................................................................................... 82
IAI X-SEL ................................................................................................................................ 84
IDEC ........................................................................................................................................ 87
INOVANCE H2U/H1U ........................................................................................................... 90
Intelligent Servo ....................................................................................................................... 92
JUSTFI Controller .................................................................................................................... 93
KERNEL SISTEMI ................................................................................................................. 95
1
KEYENCE KV series .............................................................................................................. 96
KEYENCE KV-1000 ............................................................................................................... 98
KEYENCE KV-5000 (Ethernet) ............................................................................................ 100
Korenix 6550 / 6520............................................................................................................... 102
KOYO CLICK PLC Series .................................................................................................... 104
KOYO DirectLogic ................................................................................................................ 106
KOYO DirectLogic Ethernet Module .................................................................................... 111
Lenze ...................................................................................................................................... 113
LS GLOFA Cnet .................................................................................................................... 115
LS GLOFA GM3 GM4 GM6 GM7 (Loader) ........................................................................ 117
LS MASTER-K Cnet ............................................................................................................. 119
LS MASTER-K10S1 ............................................................................................................. 121
LS MASTER-K300S CPU..................................................................................................... 123
LS XGB/XGT ........................................................................................................................ 125
LS XGB/XGT FEnet (Ethernet)............................................................................................. 127
LS XGL-CH2A Cnet.............................................................................................................. 129
LS XGL-EFMT Fenet (Ethernet) ........................................................................................... 131
LS XGT/XGK CPU DIRECT ................................................................................................ 134
LIYAN EX series ................................................................................................................... 136
Master (Master-Slave Protocol) ............................................................................................. 138
Memobus (YASKAWA MP Series controllers) .................................................................... 141
Memory Map protocol ........................................................................................................... 145
MITSUBISHI A1S ................................................................................................................. 147
MITSUBISHI A2A ................................................................................................................ 150
MITSUBISHI A2US .............................................................................................................. 153
MITSUBISHI A3N/A1SH ..................................................................................................... 155
MITSUBISHI AJ71 ............................................................................................................... 158
MITSUBISHI MELSEC-Q (Ethernet) ................................................................................... 160
MITSUBISHI FX0n/FX2....................................................................................................... 165
MITSUBISHI FX2n ............................................................................................................... 167
MITSUBISHI FX232/485BD ................................................................................................ 169
MITSUBISHI FX3U/FX3G ................................................................................................... 172
MITSUBISHI FX3U-ETHERNET ........................................................................................ 174
MITSUBISHI Q00J CPU....................................................................................................... 181
MITSUBISHI Q02H .............................................................................................................. 183
MITSUBISHI Q01U Q02U ................................................................................................... 185
MITSUBISHI Q00UJ Q01U Q02U USB .............................................................................. 187
MITSUBISHI Q06H .............................................................................................................. 189
MITSUBISHI Q00/Q00UJ/Q01/QJ71 ................................................................................... 191
MITSUBISHI QJ71E71 ......................................................................................................... 195
2
MODBUS ASCII ................................................................................................................... 202
MODBUS RTU ...................................................................................................................... 205
MODBUS RTU (zero-based addressing)............................................................................... 208
MODBUS SERVER (Modbus RTU Slave)........................................................................... 212
MODBUS TCP/IP .................................................................................................................. 216
MODBUS TCP/IP 32bit ........................................................................................................ 218
MODBUS TCP/IP (zero-based) ............................................................................................. 220
Moeller XC-CPU101 ............................................................................................................. 222
Modicon Twido ...................................................................................................................... 224
OMRON C/CQM1 series ....................................................................................................... 226
OMRON CJ1/CS1.................................................................................................................. 228
OMRON CJ1/CS1 Ethernet ................................................................................................... 230
OMRON E5CN ...................................................................................................................... 233
Panasonic FP .......................................................................................................................... 235
Panasonic FP Ethernet............................................................................................................ 238
Panasonic FP2 (Ethernet) ....................................................................................................... 241
Panasonic MINAS A4 Series ................................................................................................. 244
Parker Compax3 ..................................................................................................................... 248
Parker SLVD Servo................................................................................................................ 251
SAIA PCD PGU mode ........................................................................................................... 253
SAIA PCD S-Bus mode ......................................................................................................... 255
Schleicher XCX20C ............................................................................................................... 257
Schleicher XCX 300 .............................................................................................................. 259
SEW Eurodrive MOVITRAC ................................................................................................ 262
SIEMENS S7/1200 (Ethernet) ............................................................................................... 264
SIEMENS S7/200 .................................................................................................................. 269
SIEMENS S7/200 Ethernet .................................................................................................... 271
SIEMENS S7/300 .................................................................................................................. 273
SIEMENS S7/300 Ethernet .................................................................................................... 275
SIEMENS S7/300 MPI .......................................................................................................... 277
SIMATIC TI505..................................................................................................................... 279
TECO (TAIAN TP02)............................................................................................................ 282
TECO (TAIAN TP03)............................................................................................................ 284
Telemecanique UniTelWay ................................................................................................... 286
TECO Inverter ........................................................................................................................ 288
TOSHIBA T series ................................................................................................................. 290
TOSHIBA TC mini series ...................................................................................................... 292
TOSHIBA VF-S11 ................................................................................................................. 294
VIGOR ................................................................................................................................... 297
YASGAWA SMC3010 .......................................................................................................... 299
3
YASKAWA SMC 3010 (ETHERNET)................................................................................. 302
YAMAHA ERCD .................................................................................................................. 305
Yokogawa FA-M3 ................................................................................................................. 307
Yokogawa FA-M3 (Ethernet) ................................................................................................ 313
MT6050i Com Port Connection Guide .................................................................................. 316
AIBUS
UDIAN Automation AI-501, AI-518, AI-519, AI-701, AI-702M, AI-704M, AI-706M, AI-719
http://www.yudian.us
HMI Setting:
Parameters
PLC type
Com port
Baud rate
Parity bit
Data Bits
Stop Bits
HMI Station No.
PLC Station No.
Recommend
AIBUS
RS485 2W
9600
None
8
2
0
1
Online Simulator
YES
Extend address mode
NO
Option
RS232
9600, 19200
0-100
PLC Setting:
Communication mode
Notes
Device address:
AI-518
Bit/Word
Device Type
Format
Range
Memo
00H
dd
01H
dd
-1999~+9999
HIAL
02H
dd
-1999~+9999
LoAL
03H
dd
0~9999
dHAL
04H
dd
0~9999
dLAL
05H
dd
0~2000
dF
06H
dd
0~4
CtrL
07H
dd
0~9999
M5
08H
dd
1~9999
09H
dd
0~2000
10
0AH
dd
0~125
CtI
11
0BH
dd
0~37
Sn (read only)
12
0CH
dd
0~3
dIP (read only)
13
0DH
dd
-1999~+9999
dIL
14
0EH
dd
-1999~+9999
dIH
15
0FH
dd
0~9999
ALP
16
10H
dd
-1999~+4000
0.1
17
11H
dd
0~48
Op1
18
12H
dd
-110~+110%
oPL
19
13H
dd
0~110%
oPH
20
14H
dd
0~127
SV/STEP
dd
21
15H
Sc
CF (read only)
Baud ratebAud
0~19.2K
/808Pstatus word:
run:0 suspend:4 stop:12
(read only)
22
16H
dd
0~100
ADDR
23
17H
dd
0~20
dL
24
18H
dd
0~127
Run
25
19H
dd
0~9999
Loc
AI-701
Bit/Word
Device Type
Format
Range
Memo
01H
dd
-9990~+30000
HIAL
02H
dd
-9990~+30000
LoAL
03H
dd
-9990~+30000
HdAL
04H
dd
-9990~+30000
LdAL
05H
dd
0~2000
AHYS
11
0BH
dd
0~37
InP (read only)
12
0CH
dd
0~3
dPt
13
0DH
dd
-9999~+30000
SCL
14
0EH
dd
-9999~+30000
SCH
15
0FH
dd
0~4444
AOP
16
10H
dd
-1999~+4000
0.1
Scb
17
11H
dd
0~48
Opt
dd
21
15H
Baud ratebAud
0~19.2K
/808P status word
run:0 suspend:4 stop:12
(read only)
22
16H
dd
0~80
ADDR
23
17H
dd
0~40
FILt
25
19H
dd
0~255
Loc
Wiring diagram:
RS-485:
MT8000 PLC[485]
AI-518/518P
9P D-SUB
RS485 port
COM1
COM3
RX-
Data-
COMM A
RX+
Data+
COMM B
GND
GND
Driver Version:
Version
Date
Description of Changes
7
V1.20
Dec/30/2008
Allen-Bradley CompactLogix / FlexLogix
Allen-Bradley ControlLogix, CompactLogix, FlexLogix CH0 DF1
http://www.ab.com
HMI Setting:
Parameters
Recommend
PLC type
Allen-Bradley
Option
CompactLogix/FlexLogix
Com port
RS232
Baud rate
19200
9600, 19200, 38400
Parity bit
None
Even, Odd, None
Data Bits
Stop Bits
HMI Station No.
PLC Station No.
1-31
PLC Setting:
Communication mode
DF1 Full Duplex protocol 19200, None, 8, 1 (default)
Error Check: BCC, Station Address: 1
Notes
Device address:
Bit/Word
Device Type
Format
Range
B_BOOL
fffddd(dd)
File no. ff: 3, 10~255
Memo
Bit data file
Element no. ddd: 0~255
Bit no. (dd): 0~15
File no. ff: 7, 10~255
N_BOOL
fffddd(dd)
Element no. ddd: 0~255
Integer data file bit level (N7,
10~255)
Bit no. (dd): 0~15
Bx_INT
File no. fff: 3, 10~255
Bit data file word level
Element no. ddd: 0~255
Tx.PRE
DW
DW
fffddd
fffddd
File no. fff: 4, 10~255
Timer Preset Value (T4, T10~255)
Element no. ddd: 0~255
Tx.ACC
fffddd
File no. fff: 4, 10~255
Element no. ddd: 0~255
Cx.PRE
DW
fffddd
File no. fff: 5, 10~255
Timer
Accumulator
Value
(T4,
T10~255)
Counter Preset Value (C5, C10~255)
Element no. ddd: 0~255
fffddd
DW
Cx.ACC
F8_REAL
ddd
Fx_REAL
fffddd
DW
Nx_INT
Fffddd
File no. fff: 5, 10~255
Element no. ddd: 0~255
ddd:0~255
Counter Accumulator Value (C5,
C10~255)
Floating point data file (F8)
File no. fff:0~255
Element no. ddd:0~255
File no. fff:0~255
Floating
RS-232: ControlLogix, CompactLogix CPU CH0
COM2
COM3
3 TX
2 RX
5 GND
4 TX
6 RX
5 GND
7 TX
8 RX
5 GND
AB CPU CH0
RS-232
9P D-SUB Male
2
3
5
file
Integer data file (N7, 10~255)
Wiring diagram:
COM1
data
F010~F255)
Element no. ddd:0~255
MT8000 RS232
9P D-SUB Female
point
RD
TD
GND
(F008,
ControlLogix, CompactLogix CPU CH0 setting:
Create the Tag:
The name format must use 4 chars like B003, T004, C005, N007, F008.
Two or three chars are not available. For example B03 or B3.
10
Driver Version:
Version
Date
V1.20
Dec/30/2008
Description of Changes
11
Allen-Bradley DF1
Allen-Bradley MicroLogix 1000, 1100, 1200, 1500, SLC 5/03, 5/04, 5/05
http://www.ab.com
Note: Allen-Bradley DF1 driver is used CRC checksum.
HMI Setting:
Parameters
PLC type
Com port
Baud rate
Parity bit
Data Bits
Stop Bits
HMI Station No.
PLC Station No.
Recommend
AB DF1
RS232
19200
None
8
1
0
1
Option
Notes
9600, 19200, 38400
Even, Odd, None
8
1
1-31
PLC Setting:
Communication mode
DF1 Full Duplex protocol 19200, None, 8, 1 (default)
Error Check: CRC
Device address:
Bit/Word
B
B
B
B
B
Device Type
I1
O0
S_Bit
B3
B10~13
Format
ddd(dd)
ddd(dd)
ddd(dd)
ddd(dd)
ddd(dd)
Bfn
fffddd(dd)
NfnBit
fffddd(dd)
W
W
S
T4SV
TfnSV
ddd
ddd
fffddd
T4PV
TfnPV
ddd
fffddd
C5SV
CfnSV
ddd
fffddd
C5PV
ddd
W
W
W
W
W
W
Range
ddd:0~254
(dd): 0~15
ddd:0~254
(dd): 0~15
ddd:0~254
(dd): 0~15
ddd:0~254
(dd): 0~15
ddd:0~254
(dd): 0~15
File no. fff: 3, 10~254
Element no. ddd: 0~254
Bit no. (dd): 0~15
File no. fff: 7, 10~254
Element no. ddd: 0~254
Bit no. (dd): 0~15
ddd:0~254
ddd:0~254
File no. fff: 4, 10~254
Element no. ddd:0~254
ddd:0~254
File no. fff: 4, 10~254
Element no. ddd:0~254
ddd:0~254
File no. fff: 5, 10~254
Element no. ddd:0~254
ddd:0~254
12
Memo
Input (I)
Output (O)
Status (S) bit level
Bit data file (B3)
Bit data file (B10~13)
Bit data file (B3, 10~254)
Integer data file bit level (N7,
10~254)
Status (S)
Timer Preset Value (T4)
Timer Preset Value
Timer Accumulator Value (T4)
Timer Accumulator Value
Counter Preset Value (C5)
Counter Preset Value
Counter Accumulator Value (C5)
Bit/Word
Device Type
Format
fffddd
CfnPV
W
W
W
N7
N10~15
F8
ddd
ddd
ddd
Nfn
fffddd
Range
File no. fff: 5, 10~254
Element no. ddd:0~254
ddd:0~254
ddd:0~254
ddd:0~254
File no. fff:0~254
Element no. ddd:0~254
Memo
Counter Accumulator Value
Integer data file (N7)
Integer data file (N10~15)
Floating point data file (F8)
Integer data file (N7, 10~254)
Wiring diagram:
RS-232: MicroLogix 1000, 1100, 1200, 1500
MicroLogix RS232
mini-DIN 8pin
MT8000 RS232
9P D-SUB
COM1
COM2
COM3
3 TX
2 RX
5 GND
4 TX
6 RX
5 GND
7 TX
8 RX
5 GND
RXD
TXD
GND
RS-232: SLC5/03, 04, 05 CH0
AB CPU CH0
RS-232
9P D-SUB Male
MT8000 RS232
9P D-SUB Female
COM1
COM2
COM3
3 TX
2 RX
5 GND
4 TX
6 RX
5 GND
7 TX
8 RX
5 GND
2
3
5
RD
TD
GND
Driver Version:
Version
Date
V2.10
Apr/17/2009
Description of Changes
13
Allen-Bradley DF1 BCC
Allen-Bradley MicroLogix 1000, 1100, 1200, 1500, SLC 5/03, 5/04, 5/05
http://www.ab.com
Note: Allen-Bradley DF1 BCC is the same as Allen-Bradley DF1. the only different is this driver
use BCC checksum.
HMI Setting:
Parameters
PLC type
Com port
Baud rate
Parity bit
Data Bits
Stop Bits
HMI Station No.
PLC Station No.
Recommend
AB DF1
RS232
19200
None
8
1
0
1
Option
Notes
9600, 19200, 38400
Even, Odd, None
8
1
1-31
PLC Setting:
Communication mode
DF1 Full Duplex protocol 19200, None, 8, 1 (default)
Error Check: CRC
Device address:
Bit/Word
B
B
B
B
B
Device Type
I1
O0
S_Bit
B3
B10~13
Format
ddd(dd)
ddd(dd)
ddd(dd)
ddd(dd)
ddd(dd)
Bfn
fffddd(dd)
NfnBit
fffddd(dd)
W
W
S
T4SV
TfnSV
ddd
ddd
fffddd
T4PV
TfnPV
ddd
fffddd
C5SV
ddd
W
W
W
W
Range
ddd:0~254
(dd): 0~15
ddd:0~254
(dd): 0~15
ddd:0~254
(dd): 0~15
ddd:0~254
(dd): 0~15
ddd:0~254
(dd): 0~15
File no. fff: 3, 10~254
Element no. ddd: 0~254
Bit no. (dd): 0~15
File no. fff: 7, 10~254
Element no. ddd: 0~254
Bit no. (dd): 0~15
ddd:0~254
ddd:0~254
File no. fff: 4, 10~254
Element no. ddd:0~254
ddd:0~254
File no. fff: 4, 10~254
Element no. ddd:0~254
ddd:0~254
14
Memo
Input (I)
Output (O)
Status (S) bit level
Bit data file (B3)
Bit data file (B10~13)
Bit data file (B3, 10~254)
Integer data file bit level (N7,
10~254)
Status (S)
Timer Preset Value (T4)
Timer Preset Value
Timer Accumulator Value (T4)
Timer Accumulator Value
Counter Preset Value (C5)
Bit/Word
Device Type
CfnSV
Format
fffddd
C5PV
CfnPV
ddd
fffddd
W
W
W
N7
N10~15
F8
ddd
ddd
ddd
Nfn
fffddd
Range
File no. fff: 5, 10~254
Element no. ddd:0~254
ddd:0~254
File no. fff: 5, 10~254
Element no. ddd:0~254
ddd:0~254
ddd:0~254
ddd:0~254
File no. fff:0~254
Element no. ddd:0~254
Memo
Counter Preset Value
Counter Accumulator Value (C5)
Counter Accumulator Value
Integer data file (N7)
Integer data file (N10~15)
Floating point data file (F8)
Integer data file (N7, 10~254)
Wiring diagram:
RS-232: MicroLogix 1000, 1100, 1200, 1500
MicroLogix RS232
mini-DIN 8pin
MT8000 RS232
9P D-SUB
COM1
COM2
COM3
3 TX
2 RX
5 GND
4 TX
6 RX
5 GND
7 TX
8 RX
5 GND
RXD
TXD
GND
RS-232: SLC5/03, 04, 05 CH0
AB CPU CH0
RS-232
9P D-SUB Male
MT8000 RS232
9P D-SUB Female
COM1
COM2
COM3
3 TX
2 RX
5 GND
4 TX
6 RX
5 GND
7 TX
8 RX
5 GND
2
3
5
RD
TD
GND
Driver Version:
Version
Date
V2.10
Apr/17/2009
Description of Changes
15
Allen-Bradley DH485
Allen-Bradley MicroLogix 1000, 1100, 1200, 1500, SLC 5/03, 5/04, 5/05
http://www.ab.com
HMI Setting:
Parameters
Recommend
PLC type
Allen-Bradley DH485
Com port
RS485 2W
RS232
Baud rate
19200
9600, 19200
Parity bit
Even
Data Bits
Stop Bits
HMI Station NO.
PLC Station NO.
1-31
Online Simulator
YES
Extend address mode
NO
Option
Notes
PLC Setting:
Communication mode
DH485 protocol 19200 (default)
Set the Max. Node Address as exactly how many PLCs you
have.
16
Device address:
Bit/Word
Device
Type
Format
Range
Memo
I1
ddd(dd)
ddd:0~254
(dd): 0~15
Input (I)
O0
ddd(dd)
ddd:0~254
(dd): 0~15
Output (O)
B3
ddd(dd)
ddd:0~254
(dd): 0~15
Bit data file (B3)
B10~13
ddd(dd)
ddd:0~254
(dd): 0~15
Bit data file (B10~13)
Bfn
fffddd(dd)
File no. fff: 3, 10~254
Bit data file (B3, 10~254)
Element no. ddd: 0~254
Bit no. (dd): 0~15
NfnBit
fffddd(dd)
File no. fff: 7, 10~254
Integer data file bit level (N7,
Element no. ddd: 0~254
10~254)
Bit no. (dd): 0~15
B
S_Bit
ddd(dd)
ddd:0~254 (dd): 0~15
T4SV
ddd
ddd:0~254
Timer Preset Value (T4)
T4PV
ddd
ddd:0~254
Timer Accumulator Value (T4)
C5SV
ddd
ddd:0~254
Counter Preset Value (C5)
C5PV
ddd
ddd:0~254
Counter Accumulator Value (C5)
TfnSV
fffddd
File no. fff:0~254
Status file
Timer Preset Value
Element no. ddd:0~254
TfnPV
fffddd
File no. fff:0~254
Timer Accumulator Value
Element no. ddd:0~254
File no. fff:0~254
Counter Preset Value
CfnSV
fffddd
CfnPV
fffddd
N7
ddd
ddd:0~254
Integer data file (N7)
N10~15
ddd
ddd:0~254
Integer data file (N10~15)
F8
ddd
ddd:0~254
Floating point data file (F8)
Nfn
fffddd
ddd
Element no. ddd:0~254
File no. fff:0~254
Counter Accumulator Value
Element no. ddd:0~254
File no. fff:0~254
Integer data file (N7, 10~254)
Element no. ddd:0~254
ddd:0~254
17
Status file
Wiring diagram:
RS-485: SLC500 Fixed type, SLC5/01,02,03 CH1.
MT8000 cant connect to 1747-AIC PERIPHERAL PORT
AB SLC500 DH485
RJ8 clip style ports
MT8000 RS485
9P D-SUB
COM1
COM3
1 RX2 RX+
5 GND
6 Data9 Data+
5 GND
2
1
SDB
SDA
GND
RS-232: MicroLogix 1000, 1100, 1200, 1500 must set DH485 protocol.
MicroLogix RS232
mini-DIN 8pin
MT8000 RS232
9P D-SUB
COM1
COM2
COM3
3 TX
2 RX
5 GND
4 TX
6 RX
5 GND
7 TX
8 RX
5 GND
RXD
TXD
GND
RS-232: SLC5/03,04,05 CH0 must set DH485 protocol.
AB CPU CH0
RS-232
9P D-SUB Male
MT8000 RS232
9P D-SUB Female
COM1
COM2
COM3
3 TX
2 RX
4 TX
6 RX
7 TX
8 RX
GND
GND
GND
2
3
RD
TD
GND
Caution: AB DH485 supports MT8000 X and iH series only.
Driver Version:
Version
Date
V1.20
Apr/17/2009
Description of Changes
18
Allen-Bradley EtherNet/IP CompactLogix
Allen-Bradley ControlLogix, CompactLogix, FelxLogix Ethernet
http://www.ab.com
HMI Setting:
Parameters
Recommend
PLC type
Allen-Bradley EtherNet
Option
Notes
(CompactLogix)
Com port
Ethernet
Port no.
44818
PLC Station No.
PLC Setting:
Communication mode
Device address:
Bit/Word
Device Type
Format
Range
Memo
Bx_BOOL
ffddd(dd)
File no. ff: 3, 10~99
Bit data file
Element no. ddd: 0~999
Bit no. (dd): 0~15
File no. ff: 7, 10~99
Nx_BOOL
ffddd(dd)
Integer data file bit level (N7, 10~99)
Element no. ddd: 0~999
Bit no. (dd): 0~15
Bx_INT
fffddd
File no. fff: 3, 10~255
Bit data file word level
Element no. ddd: 0~255
File no. fff:0~255
Integer data file (N7, 10~99)
Nx_INT
fffddd
F8_REAL
ddd
ddd:0~255
Floating point data file (F8)
Fx_REAL
fffddd
File no. fff:0~255
Floating point data file (F8)
Element no. ddd:0~255
19
ddd:0~255
DW
DW
DW
DW
Tx.PRE
fffddd
File no. fff: 4, 10~255
Timer Preset Value (T4, T10~255)
Element no. ddd: 0~255
Tx.ACC
fffddd
Cx.PRE
fffddd
File no. fff: 4, 10~255
Timer Accumulator Value (T4,
Element no. ddd: 0~255
T10~255)
File no. fff: 5, 10~255
Counter Preset Value (C5, C10~255)
Element no. ddd: 0~255
fffddd
Cx.ACC
File no. fff: 5, 10~255
Counter Accumulator Value (C5,
Element no. ddd: 0~255
C10~255)
Wiring diagram:
Ethernet:
MT8000 Ethernet
Wire color
Ethernet Hub or Switch
RJ45
RJ45
TX+
White/Orange
RX+
TX-
Orange
RX-
RX+
White/Green
TX+
BD4+
Blue
BD4+
BD4-
White/Blue
BD4-
RX-
Green
TX-
BD3+
White/Brown
BD3+
BD3-
Brown
BD3-
Ethernet: Direct connect (crossover cable)
MT8000 Ethernet
Wire color
CPU Ethernet port
RJ45
RJ45
TX+
White/Orange
RX+
TX-
Orange
RX-
RX+
White/Green
TX+
BD4+
Blue
BD4+
BD4-
White/Blue
BD4-
RX-
Green
TX-
BD3+
White/Brown
BD3+
BD3-
Brown
BD3-
RSLogix 5000 setting
Create the Tag:
The name format must use 4 chars like B003, T004, C005, N007, F008.
Two or three chars are not available. For example B03 or B3.
20
RJ45
connector
Driver Version:
Version
Date
V1.10
Dec/30/2008
Description of Changes
21
Allen-Bradley EtherNet/IP (DF1)
Allen-Bradley MicroLogix 1100, 1400, SLC5/05 Ethernet port.
MicroLogix1000, 1200, 1500, SLC 5/03, 5/04 with 1761-NET-ENI
HMI Setting:
Parameters
Recommend
PLC type
Option
Notes
Allen-Bradley EtherNet/IP (DF1)
Com port
Ethernet
TCP Port no.
44818
HMI Station No.
PLC Station No.
PLC Setting:
Communication mode
Port Setting: 10/100 Mbps Full Duplex/Half Duplex
Device address:
Bit/Word
Device
Type
Format
Range
Memo
I1
ddd(dd)
ddd:0~254
(dd): 0~15
Input (I)
O0
ddd(dd)
ddd:0~254
(dd): 0~15
Output (O)
B3
ddd(dd)
ddd:0~254
(dd): 0~15
Bit data file (B3)
File no. fff: 3, 10~254
B
Bfn
fffddd(dd)
Bit data file (B3, 10~254)
Element no. ddd: 0~254
Bit no. (dd): 0~15
NfnBit
fffddd(dd)
File no. fff: 7, 10~254
Integer data file bit level (N7,
Element no. ddd: 0~254
10~254)
Bit no. (dd): 0~15
W
T4SV
ddd
ddd:0~254
Timer Preset Value (T4)
T4PV
ddd
ddd:0~254
Timer Accumulator Value (T4)
C5SV
ddd
ddd:0~254
Counter Preset Value (C5)
C5PV
ddd
ddd:0~254
Counter Accumulator Value (C5)
N7
ddd
ddd:0~254
Integer data file (N7)
Nfn
fffddd
File no. fff:0~254
Integer data file (N7, 10~254)
32bit Float
F8
ddd
Element no. ddd:0~254
ddd:0~254
22
Floating point data file (F8)
32bit Float
Ffn
fffddd
DW
Lfn
fffddd
File no. fff:0~254
Floating point data file (F8, 10~254)
Element no. ddd:0~254
File no. fff:0~254
Driver version 2.00 or above support
Element no. ddd:0~254
Wiring diagram:
Ethernet: Direct connect (crossover cable)
COM
CPU
PWR
RS232 DF1
Ethernet
Crossover cable
Micro Logix 1000, 1200,
MT8000
MT8000 Ethernet
1761-NET-ENI
Wire color
1500, SLC 5/03, 5/04
PLC
RJ45
RJ45
TX+
White/Orange
RX+
TX-
Orange
RX-
RX+
White/Green
TX+
BD4+
Blue
BD4+
BD4-
White/Blue
BD4-
RX-
Green
TX-
BD3+
White/Brown
BD3+
BD3-
Brown
BD3-
23
Ethernet:
Switch Hub
MT8000
SLC 500
MT8000 Ethernet
Wire color
SLC 500
SLC 500
Ethernet Hub or Switch
RJ45
RJ45
TX+
White/Orange
RX+
TX-
Orange
RX-
RX+
White/Green
TX+
BD4+
Blue
BD4+
BD4-
White/Blue
BD4-
RX-
Green
TX-
BD3+
White/Brown
BD3+
BD3-
Brown
BD3-
Driver Version:
Version
Date
V1.9
Apr/17/2009
V2.00
Dec/21/2009
Description of Changes
Add Lfn register
24
RJ45
connector
Allen Bradley EtherNet/IP-Tag
(CompactLogix/ControlLogix)
Allen-Bradley ControlLogix, CompactLogix, FelxLogix Ethernet
http://www.ab.com
HMI Setting:
Parameters
Recommend
Option
PLC type
Allen-Bradley EtherNet/IP-Tag (CompactLogix/ControlLogix)
Com port
Ethernet
Port no.
44818
PLC Station No.
PLC Setting:
Communication mode
1. Set PLC IP address.
25
Notes
2. Create Tags.
3. Export Tags data to CSV file.
26
4. In EB8000, create Allen-Bradley EtherNet/IP-Tag (CompactLogix/ControlLogix) driver.
Input PLC IP address. In System Parameter Settings dialog click [Import Tag] button.
5. In object dialog, select PLC, click Tag and select a controller tag.
27
Device address:
PLC Data Type Name
BOOL
INT
Bit/Word
Boolean
Integer
EB8000 Data format
Bit object
16-bit signed, ASCII
Memo
DINT
Double Integer
32-bit signed
-231~(231-1)
REAL
Single Precision Float
32-bit Float
IEEE 754
-32768~32767
Wiring diagram:
Ethernet:
MT8000 Ethernet
RJ45
Wire color
Ethernet Hub or Switch
RJ45
TX+
White/Orange
RX+
TX-
Orange
RX-
RX+
White/Green
TX+
BD4+
Blue
BD4+
BD4-
White/Blue
BD4-
RX-
Green
TX-
BD3+
White/Brown
BD3+
BD3-
Brown
BD3-
Ethernet: Direct connect (crossover cable)
MT8000 Ethernet
RJ45
Wire color
CPU Ethernet port
RJ45
TX+
White/Orange
RX+
TX-
Orange
RX-
RX+
White/Green
TX+
BD4+
Blue
BD4+
BD4-
White/Blue
BD4-
RX-
Green
TX-
BD3+
White/Brown
BD3+
BD3-
Brown
BD3-
28
RJ45
connector
Allen Bradley PLC5
http://www.ab.com
HMI Setting:
Parameters
Recommend
Option
Notes
PLC type
AB PLC5
Com port
RS232
Baud rate
19200
9600, 19200
Parity bit
None
Even, Odd, None
Data Bits
Stop Bits
HMI Station No.
PLC Station No.
1-31
PLC Setting:
Communication mode
DF1 Full Duplex protocol 19200, None, 8, 1 (default)
Device address:
Bit/Word
Device Type
Format
Range
I1
ddd(dd)
ddd:0~254
(dd): 0~15
Input (I)
O0
ddd(dd)
ddd:0~254
(dd): 0~15
Output (O)
B3
ddd(dd)
ddd:0~254
(dd): 0~15
Bit data file (B3)
B10~13
ddd(dd)
ddd:0~254
(dd): 0~15
Bit data file (B10~13)
T4SV
ddd
ddd:0~254
Timer Preset Value (T4)
T4PV
ddd
ddd:0~254
Timer Accumulator Value (T4)
C5SV
ddd
ddd:0~254
Counter Preset Value (C5)
C5PV
ddd
ddd:0~254
Counter Accumulator Value (C5)
N7
ddd
ddd:0~254
Integer data file (N7)
N10~15
ddd
ddd:0~254
Integer data file (N10~15)
F8
ddd
ddd:0~254
Floating point data file (F8)
Nfn
fffddd
File no. fff:7,9~254
Integer data file (V2.5.0 or newer)
W
W
Memo
Element no. ddd:0~254
Ffn
fffddd
File no. fff:8,9~254
29
Floating point data file (V2.5.0 or
Bit/Word
Device Type
Format
Range
Memo
Element no. ddd:0~254
newer)
Allen-Bradley PLC-5 Family PLCs using the DF1 Full Duplex protocol.
For the PLC-5/10, PLC-5/15 and PLC-5/25 the MT8000 should be connected to:
the DF1 port on the 1785-KE module;
for the PLC-5/11, PLC-5/20, PLC-5/30 and PLC-5/40 the MT8000 should be connected to:
the Channel 0 Port on the PLC.
Wiring diagram:
RS-232: PLC5 CPU CH0
EasyView MT8000
9P D-SUB
AB CPU CH0 RS-232
COM1 [RS232] COM2 [RS232] COM3 [RS232]
25P D-SUB
3
2
5
3
2
7
TX
RX
GND
4 TX
6 RX
5 GND
7 TX
8 RX
5 GND
Driver Version:
Version
Date
V1.20
Apr/17/2009
Description of Changes
30
RXD
TXD
GND
31
Altus ALNET-I
Altus SeriesMode : PO3042, PO3142, PO3242, PO3342, PL103 ,PL104,
PL105, QK800, QK801, QK2000.
HMI Setting:
Parameters
Recommend
PLC type
Altus ALNET-I
Com port
RS232
Station no.
Baud rate
9600
Parity bit
even
Data Bits
Stop bit
Option
Notes
Device address:
Bit/Word
Device Type
Format
Range
Device Range
M_Bit
dddd(h)
0~ 1023f
Memories
ddd(h)
0 ~ 511f
Auxiliary Relays
ddd(h)
0 ~ 511f
Input Relays
D_Bit
dddd(dd)
0 ~ 102331
Decimals
F_Bit
dddd(dd)
0 ~ 102331
Reals
I_Bit
dddd(dd)
0 ~ 102331
Integers
ddd(h)
0 ~ 511f
Output Relays
dddd
0 ~ 1023
Memories
DW
dddd
0 ~ 1023
Decimals
DW
dddd
0 ~ 1023
Reals
DW
dddd
0 ~ 1023
Integers
TM
hhhh
DW
TD
hhhh
DW
TF
hhhh
DW
TI
hhhh
0 ~ FFFF
0 ~ FFFF
0 ~ FFFF
0 ~ FFFF
Note: TM, TD, TF and TI in PLC softwares format is TXA[B],
Memory Tables
Decimal Tables
Real Tables
Integer Tables
, , , I types are X.
B address range is 0 ~ FF and A address range is 0 ~ FF; the device type is AABB, the range is depend on
the PLC settings.
For example Model PO3242 range is 0 and B range is 0 ~ 7.
32
Wiring diagram:
PLC PO3042, PO3142, PO3242, PO3342
MT8000 RS232 9P D-SUB
PLC COM1 RS232
COM1
COM2
COM3
RJ45 Port
TX
TX
TX
RX
RX
RX
RX
TX
GND
GND
GND
GND
PLC PL103, PL104, PL105
MT8000 RS232 9P D-SUB
PLC COM1 RS232
COM1
COM2
COM3
9P D-SUB
TX
TX
TX
RX
RX
RX
RX
TX
GND
GND
GND
GND
PLC QK800,QK801,QK2000.
MT8000 RS232 9P D-SUB
PLC COM1 RS232
COM1
COM2
COM3
9P D-SUB
TX
TX
TX
RX
RX
RX
RX
TX
GND
GND
GND
GND
Driver Version:
Version
Date
V0.01
Jul/24/2009
Description of Changes
33
Baumuller Servo
http://www.baumuller.com/
HMI Setting:
Parameters
Recommend
Option
PLC type
Baumuller
Com port
RS485 4W COM1
Baud rate
19200
9600, 19200
Parity bit
Even
Even, Odd, None
Data Bits
7 or 8
Stop Bits
1 or 2
HMI Station No.
PLC Station No.
Notes
Defaults
Baumuller Servo Setting:
Communication mode
RK 512 Protocol
19200 8 1 EVEN
Device address:
Bit/Word
Device Type
Format
Range
Device Range
DB0_bit
ddd(h)
ddd:0~255 (h): 0~f
DB0
ddd
ddd:0~255
34
DB0_bit~DB29_bit
DB0~DB29
Wiring diagram:
RS-485 4W:
MT8000 HMI COM1
RS485 4W 9P D-SUB
Baumuller servo
RS-422 9P D-SUB
Female
Female
1
RX-
1 TXD-
RX+
9 TXD+
TX-
5 RXD-
TX+
6 RXD+
GND
8 GND
Driver Version:
Version
Date
V1.10
Apr/17/2009
Description of Changes
35
Cimon CM1-CP4A
Cimon CM1 series, CP4A module
http://www.kdtsys.com
HMI Setting:
Parameters
Recommend
Option
PLC type
Cimon CM1-CP4A/ECO1A
Com port
RS232
Notes
PLC station No. 1
Baud rate
38400
Data bit
Parity bit
None
Stop bit
PLC Setting:
Bit/Word
Device type
Format
Range
Memo
dd(h)
0 ~ 23F
dd(h)
0 ~ 23F
ddd(h)
0 ~ 511F
ddd(h)
0 ~ 127F
dddd
0 ~ 1023
dddd
0 ~ 1023
ddd(h)
0 ~ 127F
ddd(h)
0 ~ 127F
dddd
0 ~ 4999
dd
0 ~ 99
TS
dddd
0 ~ 1023
TC
dddd
0 ~ 1023
CC
dddd
0 ~ 1023
CS
dddd
0 ~ 1023
36
0-1F read only
Read only
Max. range: 99
Wiring diagram:
EasyView MT8000 HMI
9P D-SUB
CM1-CP4A
6P RJ-11 Female
COM1 [RS232] COM2 [RS232] COM3 [RS232]
3
2
5
TX
RX
GND
4 TX
6 RX
5 GND
7 TX
8 RX
5 GND
3
2
5
Driver Version:
Version
Date
V1.00
Nov/30/2009
Description of Changes
37
RXD
TXD
GND
6P RJ-11 Female
Cimon CM1-SC02A
Cimon CM series, SC02A module
http://www.kdtsys.com
HMI Setting:
Parameters
Recommend
Option
PLC type
Cimon CM1-SC02A
Com port
RS232
Notes
RS485, RS232
PLC station No. 1
Baud rate
38400
Data bit
Parity bit
None
Stop bit
PLC Setting:
Bit/Word
Device type
Format
Range
Memo
dd(h)
0 ~ 23F
0-1F read only
dd(h)
0 ~ 23F
0-F read only
ddd(h)
0 ~ 511F
ddd(h)
0 ~ 127F
dddd
0 ~ 1023
dddd
0 ~ 1023
ddd(h)
0 ~ 127F
ddd(h)
0 ~ 127F
dddd
0 ~ 4999
dd
0 ~ 99
TS
dddd
0 ~ 1023
TC
dddd
0 ~ 1023
CC
dddd
0 ~ 1023
CS
dddd
0 ~ 1023
38
Read only
Max. range: 99
Wiring diagram:
Cimon CM1-SC02A
RS-232
9P D-SUB Male
MT8000 RS232
9P D-SUB Female
COM1
COM2
COM3
3 TX
2 RX
5 GND
4 TX
6 RX
5 GND
7 TX
8 RX
5 GND
2
3
5
RD
TD
GND
Driver Version:
Version
Date
V1.00
Nov/30/2009
Description of Changes
39
Copley Controls
Digital Servo Driver & Controllers, Xenus, Xenus Micro, Accelnet, Accelnet Micro, Stepnet series
http://www.copleycontrols.com/motion/
HMI Setting:
Parameters
PLC type
Com port
Baud rate
Parity bit
Data Bits
Stop Bits
HMI Station No.
PLC Station No.
Recommend
Copley Controls
RS232
9600
None
8
1
0
0
Option
Notes
9600~115200
Even, Odd, None
8
1
0-127
PLC Setting:
ASCII format
Device address:
Bit/Word
W
W
W
W
Device Type
Flash INT 16
RAM INT 16
Flash INT 32
Format
hhh
hhh
hhh
RAM INT 32
hhh
Range
0~FFF
0~FFF
0~FFF
0~FFF
Memo
For Register is INT16 or U16
For Register is INT16 or U16
For Register is INT32 or U32
For Register is INT32 or U32
Wiring diagram:
Xenus, Xenus Micro, Accelnet
Xenus Micro Panel
RS-232 RJ11
J7 cable connector
MT8000 RS232
9P D-SUB
COM1
3
2
5
COM2
TX
4 TX
RX
6 RX
GND 5 GND
COM3
7 TX
8 RX
5 GND
2
5
3, 4
40
RXD
TXD
GND
Stepnet
Stepnet
RS232 RJ11
J8 cable connector
MT8000 RS232
9P D-SUB
COM1
3
2
5
COM2
TX
4 TX
RX
6 RX
GND 5 GND
COM3
7 TX
8 RX
5 GND
2
5
3, 4
RXD
TXD
GND
Accelnet Micro
Accelnet Micro Panel
RS-232
J5 cable connector
MT8000 RS232
9P D-SUB
COM1
3
2
5
COM2
TX
4 TX
RX
6 RX
GND 5 GND
COM3
7 TX
8 RX
5 GND
14
29
15
RXD
TXD
GND
Driver Version:
Version
Date
V1.20
Dec/30/2008
Description of Changes
41
CROUZET M3 (FBD)
HMI Setting:
Parameters
Recommend
Option
PLC type
CROUZET M3 (FBD)
Com port
RS232
Baud rate
115200
Data bit
Parity bit
EVEN
Stop bit
Station no.
Notes
Device address:
Bit/Word
Device Type
Format
Range
Memo
SLI_Bit
dd(f)
1(0)~24(f)
Serial link input
SLO_Bit
dd(f)
25(0)~48(f)
Serial link output (read only)
IA
dd
1 ~ 99
Analogy input (default: 1 ~ 4)
SL_IN
dd
1~24
Serial link input
SL_OUT
dd
25~48
Serial link output (read only)
Wiring diagram:
MT8000 RS232
9P D-SUB Male
CROUZET M3
RS-232
9P D-SUB Female
(Extension cable)
COM1
3 TX
2 RX
5 GND
3
2
5
RD
TD
GND
DTR
RTS
42
(3m serial link cable)
Note: Please use 3m serial link cable (Accessories from Millenium 3) and extension cable (as
above) to communicate with MT8000/6000 series.
43
CROUZET M3 (LAD)
HMI Setting:
Parameters
Recommend
Option
PLC type
CROUZET M3 (LAD)
Com port
RS232
Baud rate
115200
Data bit
Parity bit
EVEN
Stop bit
Station no.
Notes
Device address:
Bit/Word
Device Type
Format
Range
Memo
dd
1 ~ 99
Input (default: 1 ~ 4)
dd
1 ~ 99
Output (default: 1 ~ 4)
dd
1 ~ 28
Relay
SLI_Bit
dd(f)
1(0)~24(f)
Serial link input
SLO_Bit
dd(f)
25(0)~48(f)
Serial link output (read only)
IA
dd
1 ~ 99
Analogy input (default: 1 ~ 4)
dd
1 ~ 12
Timer
dd
1 ~ 16
Counter
SL_IN
dd
1~24
Serial link input
SL_OUT
dd
25~48
Serial link output (read only)
44
Wiring diagram:
MT8000 RS232
9P D-SUB Male
CROUZET M3
RS-232
9P D-SUB Female
(Extension cable)
COM1
3 TX
2 RX
5 GND
3
2
5
RD
TD
GND
DTR
RTS
(3m serial link cable)
Note: Please use 3m serial link cable (Accessories from Millenium 3) and extension cable (as
above) to communicate with MT8000/6000 series.
45
Danfoss ECL Apex20 Controller
http://www.danfoss.com/
HMI Setting:
Parameters
Recommend
PLC type
Danfoss ECL Apex20
Com port
RS232
Baud rate
9600
Parity bit
None
Data Bits
Stop Bits
PLC Station No.
Option
Notes
Device address:
Device Type
Format
Range
Flag
DDDD
0-8191
Input
DDD
0-511
Output
DDD
0-511
Register
DDDD
0-4095
Counter
DDDD
0-1599
Timer
DDDD
0-1599
Reg_Float
DDDD
0-4095
Memo
Support 32-bit float format
EB8000 device addresses range may different with PLC extended mode, please refer EB8000s
addresses range as above.
ddd:Decimal
46
Wiring diagram:
RS232:
MT8000 RS232
9P D-SUB Male
COM1
COM2
COM3
3
2
5
7 TX
8 RX
5 GND
TX
RX
GND
4 TX
6 RX
5 GND
ECL Apex20
Controller
9P D-SUB Female
2 RXD
3 TXD
5 GND
7 RTS
8 CTS
RS485:
MT8000 RS-485
9P D-SUB Female
COM1
COM3
1 RX6 Data2 RX+
9 Data+
ECL Apex20
Controller
Port# 1
11
12
MT8000 RS-485
9P D-SUB Female
COM1
COM3
1 RX6 Data2 RX+
9 Data+
ECL Apex20
Controller
Port# 0
29
28
Driver Version:
Version
Date
V1.10
Dec/30/2008
Description of Changes
47
Danfoss FC series
FC051, FC100, FC200, FC300, VLT Micro Driver.
http://www.danfoss.com/
HMI Setting:
Parameters
Recommend
PLC type
Danfoss FC Series
Com port
RS485
Baud rate
9600
Parity bit
Even
Data Bits
Stop Bits
PLC Station No.
Option
Notes
Device address:
Bit/Word
Device Type
Format
Range
Memo
Word
Parameter
09
DDD
0-1000
Set Parameter
Dword
Reference
10
DDD
0-0
Control Bus Reference
Dword
Para_Index
11
DDD(DD)
0-999999
Set Parameter(Index)
Para_Index 310.1=31001, Para_Index310.0=31000
Wiring diagram:
RS485:
MT8000 RS-485
9P D-SUB Female
FC RS485
COM1
COM3
RX-
Data-
69
RX+
Data+
68
*RW100 Set PCD1 Control Word. of station 1
*RW101 read PCD1 Status Word of station 1
*RW102 Set PCD2 Control Word. of station 2
*RW103 read PCD2 Status Word of station 2
*RW104 Set PCD3 Control Word. of station 3
*RW105 read PCD3 Status Word of station 3
*RW106 Set PCD4 Control Word. of station 4
48
*RW107 read PCD4 Status Word of station 4
Driver Version:
Version
Date
V1.00
Mar/05/2010
Description of Changes
49
Danfoss VLT2800 Series
VLT2800 series
http://www.danfoss.com/
HMI Setting:
Parameters
Recommend
Option
PLC type
Danfoss VLT2800 Series
Com port
RS485 2W
RS485 2W
Baud rate
9600
9600
Parity bit
Even
Even
Data Bits
Stop Bits
HMI Station No.
PLC Station No.
Notes
0-126
According to PLC
PLC Setting:
Communication mode
9600, Even,8,1 (default)
Device address:
Bit/Word
W
DW
Device Type
Reference
Parameter
Format
dd
ddd
Range
0
ddd:0~1000
Memo
Control Bus Reference
Set Parameter
It is relate to station number, if station number is 1,control word is RW100,RW101,if station
number is 2,the control word is RW102,RW103following this rule.
Wiring diagram:
RS-485:
VLT2800 RS485
MT8000 RS485
9P D-SUB
COM1
COM3
1 RX2 RX+
5 GND
6 Data9 Data+
5 GND
69
68
50
DD+
Driver Version:
Version
Date
V1.10
Otc/06/2008
Description of Changes
51
DELTA DVP
DELTA DVP series
http://www.deltadriver.com
HMI Setting:
Parameters
Recommend
Option
PLC type
DELTA DVP
Com port
RS232
RS232, RS485
Baud rate
9600
9600, 19200
Parity bit
Even
Even, Odd, None
Data Bits
7, 8
Stop Bits
HMI Station No.
PLC Station No.
Notes
0-255
PLC Setting:
Communication mode
Device address:
Bit/Word
Device Type
Format
Range
ooo
0 ~ 23417 (Octal)
Input
ooo
0 ~ 23417 (Octal)
Output
dddd
0 ~ 9999
Auxiliary Relay
dddd
0 ~ 9999
Step Relay
dddd
0 ~ 9999
Timer
dddd
0 ~ 9999
Counter
TV
dddd
0 ~ 9999
Timer
CV
ddd
0 ~ 127
Counter
CV2
ddd
232 ~ 255
Double word counter
dddd
0 ~ 9999
Data Register
52
Memo
Wiring diagram:
1. RS232: CPU port
DELTA DVP CPU
port
8p mini DIN
MT8000 RS232
9P D-SUB
COM1
COM2
COM3
3 TX
4 TX
7 TX
2 RX
6 RX
8 RX
5 GND 5 GND 5 GND
4
5
3/8
RXD
TXD
GND
8Pin Mini-Din Female
2. RS485: CPU port
DELTA DVP
RS-485 port
MT8000 RS232
COM1
COM3
1 RX2 RX+
6 Data9 Data+
Driver Version:
Version
Date
V1.00
Dec/30/2008
Description of Changes
53
EMERSON PLC EC20
Support Emerson PLC EC20 Series. (Modbus RTU Protocol)
HMI Setting:
Parameters
Recommend
Option
PLC type
EMERSON PLC EC20
Com port
RS232
Notes
RS232, RS422,
RS485
Baud rate
9600
9600,
19200,115200
Parity bit
Even
Even, Odd, None
Data Bits
7 or 8
Stop Bits
1 or 2
HMI Station No.
PLC Station No.
0-255
PLC Setting:
Communication mode
Modbus RTU
protocol
Device address:
Bit/Word
Device Type
Format
Range
ooo
0-377 octal
256point
0000-0255
ooo
0-377 octal
256point
1200-01455
dddd
0-1999
2000-3999
SM
ddd
0-255
4400-4655
ddd
0-991
6000-6991
ddd
0-255
8000-8255
ddd
0-255
9200-9455
dddd
0-7999
0000-7999
SD
ddd
0-255
8000-8255
dd
0-15
8500-8515
54
Memo
0000-0255
ddd
0-255
9000-9255
ddd
0-199
9500-9699
DW
C_Double
ddd
200-255
9700-9811
DW
D_Double
dddd
0-7998
0000-7999
Wiring diagram:
MT8000 RS232
Emerson EC20
9P D-SUB Male
COM1
COM1
COM2
COM3
3 TX
2 RX
5 GND
4 TX
6 RX
5 GND
7 TX
8 RX
5 GND
RXD
TXD
GND
Driver Version:
Version
Date
V1.10
Dec/30/2008
Description of Changes
55
FATEK FB series
FATEK FBs series, FB MC series, FB MA series need FB-DTBR converter.
http://www.fatek.com/
HMI Setting:
Parameters
Recommend
Option
PLC type
FATEK FB Series
Com port
RS232
Baud rate
9600
Must match the PLCs port setting.
Parity bit
Even
Must match the PLCs port setting.
Data Bits
Stop Bits
HMI Station No.
PLC Station No.
RS232/RS485/Ethernet
Notes
Must match the PLCs port setting.
Does not apply to this protocol.
0-255
Must match the PLCs port setting.
PLC Setting:
Communication mode
Device address:
Bit/Word
Device Type
Format
Range
ddd
ddd : 0~9999
Input
ddd
ddd : 0~9999
Output
ddd
ddd : 0~9999
Internal Relay
ddd
ddd : 0~9999
Step Relay
ddd
ddd : 0~9999
Timer
ddd
ddd : 0~9999
Counter
ddd
ddd : 0~9999
Data Register
ddd
ddd : 0~9999
Data Register
RT
ddd
ddd : 0~9999
Timer Register
RC
ddd
ddd : 0~9999
Counter Register
DW
DRT
ddd
ddd : 0~9999
Double word Timer Register
DW
DRC
ddd
ddd : 0~9999
Double word Counter Register
56
Memo
Wiring diagram:
1. RS232: FBs Port0
FBs
MT8000 RS232
COM1
3
2
5
COM2
4P Mini-Din Male
COM3
TX
4 TX
7 TX
RX
6 RX
8 RX
GND 5 GND 5 GND
RX
TX
GND
2. RS232: FBs communication module
FBs communication
MT8000 RS232
COM1
COM2
module
COM3
9P D-SUB Male
3
2
5
TX
4 TX
7 TX
RX
6 RX
8 RX
GND 5 GND 5 GND
RX
TX
GND
3. RS485: FBs communication module
FBs communication
module
MT8000 RS-485] 2w
COM1
COM3
3P Terminal Block
1
RX-
Data-
D-
RX+
Data+
D+
4. RS232: CPU port
FB CPU port
MT8000 RS232
15P D-SUB Male
COM1
3
2
5
COM2
COM3
TX
4 TX
7 TX
RX
6 RX
8 RX
GND 5 GND 5 GND
RX
TX
GND
RTS
CTS
5. RS485: CPU port
FB CPU port
MT8000 RS-485 2w
15P D-SUB Male
COM1
COM3
RX-
Data-
D-
RX+
Data+
D+
57
4P
Mini-Din
Female
Driver Version:
Version
Date
V1.20
Jul/09/2009
Description of Changes
58
Fuji NB Series PLC
http://www.fujielectric.co.jp/fcs/eng/
HMI Setting:
Parameters
Recommend
PLC type
Fuji NB Series
Com port
RS485 4W
Baud rate
19200
Parity bit
Odd
Data Bits
Stop Bits
PLC Station No.
Option
Notes
PLC Setting:
Communication mode
NITP protocol / PLC Password (default is 0)
Device address:
Bit/Word
Device Type
Format
Range
hhh
0~7ff
Output Relay
hhh
0~3ff
Input Relay
hhh
0~fff
Internal Relay
hhh
0~fff
Latch Relay
hh
0-ff
Counter
M_Spe
hhhh
8000-81ff
hhh
0-1ff
Timer
CV
hhh
0-3ff
Counter value
TV
hhh
0-3ff
Timer value
hhhh
0-1fff
Data Register
D_Spe
hhhh
8000-80ff
59
Memo
Special Relay
Special Register
Wiring diagram:
MT8000 HMI
FUJI NB Series
COM1 [RS485]4w
9P D-SUB
RJ45 8p connector
1
2
3
4
5
4 TX3 TX+
6 RX5 RX+
RXRX+
TXTX+
GND
Driver Version:
Version
Date
V1.10
May/05/2009
Description of Changes
60
GE Fanuc CMM
http://www.ge.com
HMI Setting:
Parameters
Recommend
Option
Notes
PLC type
GE Fanuc CMM
Com port
RS232
RS232/RS485
Baud rate
19200
9600,19200,38400,57600,115200
Must same as the PLC setting
Parity bit
Odd
Even, Odd, None
Must same as the PLC setting
Data Bits
7,8
Must set as 8 to this protocol
Stop Bits
1, 2
Must same as the PLC setting
HMI Station No.
0-255
Does not apply to this protocol
PLC Station No.
0-255
Does not apply to this protocol
PLC Setting:
Refer to related PLC manual
Device address:
Bit/Word
Device Type
Format
Range
ddd
1-10000
Input relay
ddd
1-10000
Output relay
ddd
1-10000
Auxiliary relay
ddd
1-7680
ddd
1-256
AI
ddd
1-10000
Analog input register
AQ
ddd
1-10000
Analog output register
ddd
1-32640
Data register
SA
ddd
1-128
SB
ddd
1-128
SC
ddd
1-128
ddd
1-128
61
Memo
Wiring diagram:
CPU port(90-30/VersaMax)
MT8000 COM1[485]
90-30/VersaMax
9P D-SUB
RS485 port
15P SUB-D Female
RX-
12
SDA
RX+
13
SDB
GND
GND
TX-
10
RDA
TX+
11
RDB
RT
RTSA
15
CTSA
RTSB
14
CTSB
CPU port(90-30 series CPU351/352/363/364)
MT8000 PLC[232]
90-30/90-70 series
9P D-SUB Female
RS232
port
6P RJ-11 Female
3
TX
RX
RX
TX
GND
GND
6P RJ-11 Female
MT8000 RS232
VersaMax series
9P D-SUB
COM1
COM2
COM3
RS232 port
9P SUB-D Female
TX
TX
TX
RX
RX
RX
RX
TX
GND
GND
GND
GND
CPU port(VersaMax series CPU001/002/005/E05)
COM1
COM2
COM3
VersaMax series
RS232 port
9P SUB-D Female
TX
TX
TX
RX
RX
RX
RX
TX
GND
GND
GND
GND
MT8000 RS232
9P D-SUB
62
Driver Version:
Version
Date
V1.00
20090709
Description of Changes
63
GE Fanuc SNP-X
GE Fanuc 90 & VersaMax series PLC
http://www.ge.com
HMI Setting:
Parameters
Recommend
Option
Notes
PLC type
GE Fanuc SNP-X
Com port
RS485 4w
RS232/RS485
Baud rate
19200
9600,19200,38400,57600,115200
Must same as the PLC setting
Parity bit
Odd
Even, Odd, None
Must same as the PLC setting
Data Bits
7,8
Must set as 8 to this protocol
Stop Bits
1, 2
Must same as the PLC setting
HMI Station No.
0-255
Does not apply to this protocol
PLC Station No.
0-255
Does not apply to this protocol
PLC Setting:
Refer to related PLC manual
Device address:
Bit/Word
Device Type
Format
Range
ddd
1-10000
Input relay
ddd
1-10000
Output relay
ddd
1-10000
Auxiliary relay
ddd
1-7680
ddd
1-256
AI
ddd
1-10000
Analog input register
AQ
ddd
1-10000
Analog output register
ddd
1-32640
Data register
SA
ddd
1-128
SB
ddd
1-128
SC
ddd
1-128
ddd
1-128
64
Memo
Wiring diagram:
Memo
90 VersaMax series PLC of GE FANUC includes such series as 90-30, 90-70, VersaMax Micro, VersaMax
Nano and VersaMax,etc., CPU of 90-30series can pass RS485 serial com port on module, utilize SNP serial
communication protocol of GE to connect with EasyView MT8000HMI, In addition,
CPU331/340/341/350/351/352/360/363/364 can also connect through CMM311 Communication Module,
CPU351/352/363/364 also can connect through serial com port on CPU Unit 90-70 series CPU can also connect
through CMM711 Communication Module or connect through serial com port on CPU Unit Relevant software and
hardware are set up concretely please consult the technical manual that GE GE Fanuc offered.
CPU port(90-30/VersaMax)
MT8000 COM1[485]
90-30/VersaMax
9P D-SUB
RS485 port
15P SUB-D Female
RX-
12
SDA
RX+
13
SDB
GND
GND
TX-
10
RDA
TX+
11
RDB
RT
RTSA
15
CTSA
RTSB
14
CTSB
CPU port(90-30 series CPU351/352/363/364)
MT8000 PLC[232]
90-30/90-70 series
9P D-SUB Female
RS232
port
6P RJ-11 Female
3
TX
RX
RX
TX
GND
GND
6P RJ-11 Female
VersaMax series
RS232 port
MT8000 RS232
9P D-SUB
COM1
COM2
COM3
9P SUB-D Female
TX
TX
TX
RX
RX
RX
RX
TX
GND
GND
GND
GND
65
CPU port(VersaMax series CPU001/002/005/E05)
COM1
COM2
COM3
VersaMax series
RS232 port
9P SUB-D Female
TX
TX
TX
RX
RX
RX
RX
TX
GND
GND
GND
GND
MT8000 RS232
9P D-SUB
Driver Version:
Version
Date
V1.20
Jan/09/2009
Description of Changes
66
GE Fanuc Series 90-30 (Ethernet)
GE 90-30 series, CPU model 374plus
HMI Setting:
Parameters
Recommend
PLC type
GE fanuc series 90-30
(Ethernet)
Com port
Ethernet
PLC station No.
Port No.
18245
Option
Notes
1~99
Device address:
Bit/Word
Device type
Format
Range
I_bit
dddd
1 ~ 2048
Q_bit
dddd
1 ~ 2048
M_bit
dddd
1 ~ 4096
G_bit
dddd
1 ~ 1280
T_bit
ddd
1 ~ 256
SA_bit
dd
1 ~ 32
Read Only
SB_bit
dd
1 ~ 32
Read Only
SC_bit
dd
1 ~ 32
Read Only
S_bit
dd
1 ~ 32
Read Only
dddd
1 ~ 2033
Address increases 8 words, ex:
I1, I9, I17, I25..
dddd
1 ~ 2033
the rule is same as above, ex:Q1,
Q9, Q17
dddd
1 ~ 4081
dddd
1 ~ 1256
ddd
1 ~ 241
the rule is same as above, ex:T1,
T9, T17.
SA
dd
1 ~ 17
Read Only, the rule is same as
above
SB
dd
1 ~ 17
67
Memo
the rule is same as above, ex:M1,
M9, M17..
the rule is same as above, ex:G1,
G9, G17
Read Only, the rule is same as
above
SC
dd
1 ~ 17
dd
1 ~ 17
dddd
1 ~ 9999
AI
dddd
1 ~ 2048
AQ
ddd
1 ~ 512
Read Only, the rule is same as
above
Read Only, the rule is same as
above
Wiring diagram:
Ethernet:
MT8000 Ethernet Wire color
Ethernet Hub or
RJ45
Switch RJ45
RX+
TX+
White/Orange
TX-
Orange
RX+
White/Green
TX+
BD4+
Blue
BD4+
BD4-
White/Blue
BD4-
RX-
Green
TX-
BD3+
White/Brown
BD3+
BD3-
Brown
BD3-
68
RX-
RJ45
connector
Ethernet: Direct connect (crossover cable)
MT8000 Ethernet Wire color
RJ45
Modbus TCP Device
RJ45
TX+
White/Orange
RX+
TX-
Orange
RX-
RX+
White/Green
TX+
BD4+
Blue
BD4+
BD4-
White/Blue
BD4-
RX-
Green
TX-
BD3+
White/Brown
BD3+
BD3-
Brown
BD3-
Driver Version:
Version
Date
V1.20
Jun/29/2009
Description of Changes
69
HAN YOUNG
Temperature Controller
http://hynux.com/kor/
HMI Setting:
Parameters
PLC type
Recommend
Heng Young Seires
Option
Notes
Com port
RS485 4W
Must match the PLCs port setting.
Baud rate
9600
Must match the PLCs port setting.
Parity bit
None
Even, Odd, None
Must match the PLCs port setting.
Data Bits
7 or 8
Must match the PLCs port setting.
Stop Bits
1 or 2
Must match the PLCs port setting.
PLC Station No.
0-255
Must match the PLCs port setting.
Device address:
Bit/Word
B
W
Device Type
I
D
Format
ddd
ddd
Range
1-699
1-699
Wiring diagram:
MT8000 PLC[485]
Han Young
RS485 4w 9Pin D-Sub
RS485
RX-
32
TX-
RX+
31
TX+
TX-
34
RX-
TX+
33
RX+
Driver Version:
Version
Date
V1.20
May/20/2009
Description of Changes
70
Memo
Heng Yuan Sensor
EU sereis, EU5 series, EU10 series.
http://www.hysensor.com.cn
HMI Setting:
Parameters
PLC type
Recommend
Heng Yuan Sensor
Com port
RS485 2W
Baud rate
9600
Parity bit
Even
Data Bits
Stop Bits
HMI Station No.
PLC Station No.
Option
Notes
1-31
Online Simulator
YES
Extend address mode
YES
PLC Setting:
Communication mode
Device address:
Bit/Word
W
Device Type
Parameter
Format
ddd
Range
ddd:0~1000
Memo
Wiring diagram:
EU05 series
MT8000 PLC[485]
RS485 port
9P D-SUB
COM1
COM3
RX-
Data-
RX- (Yellow)
RX+
Data+
RX+ (Green)
GND
GND
GND (Black)
71
Driver Version:
Version
Date
V1.00
Dec/30/2008
Description of Changes
72
HITACHI EH-SIO
HMI Setting:
Parameters
Recommend
PLC type
HITACHI
Option
Notes
EH-SIO
Com port
RS232
RS232, RS485
Must match the PLCs port setting.
Baud rate
19200
9600, 19200, 38400
Must match the PLCs port setting.
Parity bit
Even
Even
Must match the PLCs port setting.
Data Bits
Must match the PLCs port setting.
Stop Bits
Must match the PLCs port setting.
HMI Station No.
PLC Station No.
PLC Setting:
Communication
mode
19200,E,7,1(default)
Select
Device address :
Device
Bit/Word
B
B
B
B
B
B
Type
X
Format
Range
hhhh(h)
hhhh: 0~FFFF
Memo
External Input-bit(X)
(h):0~F
Y
hhhh(h)
hhhh: 0~FFFF
(h):0~F
External Output-bit(Y)
hhhh(h)
hhhh: 0~FFFF
(h):0~F
Data area-bit(M)
hhhh(h)
hhhh: 0~FFFF
Timer(T)
(h):0~F
R
hhhh(h)
hhhh: 0~FFFF
Internal Output(R)
(h):0~F
L
hhhh(h)
hhhh: 0~FFFF
73
Link area-bit(L)
(h):0~F
W
TC
hh
hh: 0~FF
Timer/Counter current value
WX
hhhh
hhhh: 0~270F
External Input-word(X)
WY
hhhh
hhhh: 0~270F
External Output-word(Y)
WR
hhhh
hhhh: 0~270F
Internal Output-word(R)
WL
hhhh
hhhh: 0~270F
Link area-word(L)
WM
hhhh
hhhh: 0~270F
Data area-word(M)
Wiring diagram:
EH-SIO port1/port 2 RS232
MT8000 RS-232
HITACHI EH-SIO
9P D-SUB
port1 / port 2
8pin RJ45 Male
COM1
COM2
COM3
TX
TX
TX
6 RD
RX
RX
RX
5 SD
GND
GND
GND
1 SG
Port 1 / Port 2
CTS
8 RS
8pin RJ45
Female
4 PHL
7 DR
EH-SIO port2 RS485 4wireRS422
EasyView MT8000 HMI
Hitachi EH-SIO
PLC RS485port
9PinD-SUB FEMALE
1
2
3
4
5
RXRX+
TXTX+
GND
5
4
6
7
1
74
TXTX+
RXRX+
SG
EH-SIO port2 RS485 2wire
EasyView MT8000 HMI
PLC RS485 port
9PinD-SUB FEMALE
Hitachi EH-SIO
RX-
TX-
RX+
TX+
TX-
RX-
TX+
RX+
GND
SG
75
HITACHI EHV
HITACHI Web site: http://www.hitachi-ies.co.jp/english/products/plc/index.htm
HMI Setting:
Parameters
PLC type
recommend
Option
Notes
HITACHI
EHV
Com port
Ethernet
Port no.
3004
3004~3007
Device address:
Bit/Word
Device type
Format
Range
Memo
hhhh(h)
0~FFFF(F)
External Input-bit(X)
hhhh(h)
0~FFFF(F)
External Output-bit(Y)
hhhh(h)
0~FFFF(F)
Data area-bit(M)
ddddd
0~65535
Timer(T)
hhhh(h)
0~FFFF(F)
Internal Output(R)
hhhh(h)
0~FFFF(F)
Link area-bit(L)
TC
dddd
0~2559
Timer/Counter current value
WX
hhhh
0~FFFF
External Input-word(X)
WY
hhhh
0~FFFF
External Output-word(Y)
WR
hhhh
0~FFFF
Internal Output-word(R)
WL
hhhh
0~73FF
Link area-word(L)
WM
hhhh
0~7FFF
Data area-word(M)
76
Wiring diagram:
Ethernet:
MT8000 Ethernet
RJ45
Wire color
Ethernet Hub or Switch
RJ45
TX+
White/Orange
RX+
TX-
Orange
RX-
RX+
White/Green
TX+
BD4+
Blue
BD4+
BD4-
White/Blue
BD4-
RX-
Green
TX-
BD3+
White/Brown
BD3+
BD3-
Brown
BD3-
Ethernet: Direct connect (crossover cable)
MT8000 Ethernet
RJ45
Wire color
HITACHI EHV Ethernet
RJ45
TX+
White/Orange
RX+
TX-
Orange
RX-
RX+
White/Green
TX+
BD4+
Blue
BD4+
BD4-
White/Blue
BD4-
RX-
Green
TX-
BD3+
White/Brown
BD3+
BD3-
Brown
BD3-
Driver Version:
Version
Date
V1.00
Jan/12/2010
Description of Changes
77
RJ45
connector
HITACHI H series (CPU port)
Compatible PLCs
Family
Model
HITACHI
EH-150, Micro-EH, H20, H40, H64, H200, H250, H252, H300, H302, H700, H702, H1000,
H series
H1002, H2000, H4010
HITACHI Web site: http://www.hitachi-ies.co.jp/english/products/plc/index.htm
HMI Setting:
Parameters
Recommend
PLC type
HITACHI
Option
Notes
H-Series
Com port
RS232
RS232, RS485
Must match the PLCs port
setting.
Baud rate
19200
9600, 19200, 38400
Must match the PLCs port
setting.
Parity bit
Even
Even
Must match the PLCs port
setting.
Data Bits
Must match the PLCs port
setting.
Stop Bits
Must match the PLCs port
setting.
HMI Station No.
0-255
Does not apply to this protocol.
PLC Station No.
0-255
Does not apply to this protocol.
Online Simulator
YES
Extend address mode
NO
Broadcast command
PLC Setting:
Communication mode
19200,E,7,1(default)
Select
78
NO
Device address:
Bit/Word
Device
Type
Format
Range
Memo
hhh(h)
hhh: 0~FFFF (h):0~F
External Input-bit(X)
hhh(h)
hhh: 0~FFFF (h):0~F
External Output-bit(Y)
hhh(h)
hhh: 0~FFFF (h):0~F
Data area-bit(M)
hhh(h)
hhh: 0~FFFF (h):0~F
Timer(T)
hhh(h)
hhh: 0~FFFF (h):0~F
Internal Output(R)
hhh(h)
hhh: 0~FFFF (h):0~F
Link area-bit(L)
TC
hhh
hhh: 0~FF
WX
hhh
hhh: 0~270F
External Input-word(X)
WY
hhh
hhh: 0~270F
External Output-word(Y)
WR
hhh
hhh: 0~270F
Internal Output-word(R)
WL
hhh
hhh: 0~270F
Link area-word(L)
WM
hhh
hhh: 0~270F
Data area-word(M)
Timer/Counter current value
Wiring diagram:
WARNING: If your communications cable is not wired exactly as shown in our cable assembly instructions, damage
to the MT8000 or loss of communications can result.
CPU TYPE
Port 1
Port 2
EH-150/CPU 104A
RS-232
RS-232
EH-150/CPU 208A
RS-232
RS-232
Port 1
EH-150/CPU 308A
RS-232/RS-485
RS-232
Port 2
EH-150/CPU 316A
RS-232/RS-485
RS-232
EH-150/CPU 448A
RS-232/RS-485
RS-232
Switch Number
1
OFF
Normal mode
OFF
TRNS0 operation
3, 4
5
6
Port1 transmission speed
ON
ON
4,800 bps
OFF
ON
9,600 bps
ON
OFF
19,200 bps
OFF
OFF
38,400 bps
ON
Dedicated port
PHL
Doesnt support
Default
Port2 transmission speed
79
ON
Low
9,600 bps
ON
High
38,400 bps
OFF
Low
4,800 bps
Doesnt support
OFF
High
19,200 bps
Default
OFF
(System mode)
Do not turn on.
OFF
(System mode)
Do not turn on.
Toggle-Switch
PHL
Low
PHL
High
EH-150 port1/port 2 RS232
MT8000 RS-232
HITACHI EH-150
9P D-SUB
port1 / port 2
8pin RJ45 Male
COM1
COM2
COM3
TX
TX
TX
6 RD
RX
RX
RX
5 SD
GND
GND
GND
1 SG
CTS
8 RS
4 PHL
7 DR
EH150port1 RS485 4wireRS422
EasyView MT8000 HMI
PLC RS485port
9PinD-SUB FEMALE
Hitachi EH-150
port1
8PinRJ45port
1
2
3
4
5
5
4
6
7
1
RXRX+
TXTX+
GND
TXTX+
RXRX+
SG
EH150port1 RS485 2wire
EasyView MT8000 HMI
Hitachi EH-150 port1
PLC RS485 port
9PinD-SUB FEMALE
8PinRJ45 port
RX-
TX-
RX+
TX+
TX-
RX-
TX+
RX+
GND
SG
80
Port 1 / Port 2
8pin RJ45
Female
H series CPU RS232 port
HITACHI H series CPU RS232
MT8000 PLC[232]
15p D-SUB Male
9P D-SUB Male
COM1
3
TX
3 RXD
RX
2 TXD
5 GND
8 CTS
9 SG
4 RTS
10 SG
5 CTS
7 DSR
8 PHL
14 PV12
MICRO-EH port1 RS232
MT8000 RS-232
HITACHI
9P D-SUB
MICRO-EH port1
8pin RJ45 Male
COM1
COM2
COM3
TX
TX
TX
6 RD
RX
RX
RX
5 SD
GND
GND
GND
1 SG
Port 1
CTS
8 RS
8pin RJ45
Female
4 PHL
7 DR
Driver Version:
Version
Date
V1.10
Oct/22/2009
V1.0
Dec/30/2009
Description of Changes
Fixed HMI occupies the control right of CPU module
81
HUST H4X
HUST CNC Controller H4 Series
http://www.hust.com.tw/
HMI Setting:
Parameters
Recommend
PLC type
HUST H4X
Com port
RS-232
PLC Station
Null
Option
Notes
CPU port
No.
Baud rate
38400
Data bit
Parity bit
Even
Stop bit
Turn delay
9600,19200,38400,57600
Device address:
Bit/Word
Device Type
Format
Range
Memo
1 ~ 99999
Please refer to specification of
Controller for registers range.
DW
VM
ddddd
DW
ddd
0 ~ 255
DW
Cn
ddd
0 ~ 255
DW
Tm
ddd
0 ~ 255
Mapping to VM 10512~10767 (read
only)
ddd
0 ~ 255
Mapping to VM 10800 ~ 10807 (read
only)
ddd
0 ~ 255
ddd
0 ~ 255
ddd
0 ~ 255
82
Mapping to VM 10000~10255 (read
only)
Mapping to VM 10256~10511 (read
only)
Mapping to VM 10808 ~ 10815 (read
only)
Mapping to VM 10816 ~ 10823 (read
only)
Mapping to VM 10824 ~ 10831 (read
only)
B
ddd
VM_bit
ddddd(dd)
0 ~ 255
Mapping to VM 10832 ~ 10863 (read
only)
1 ~ 99999(31)
Bit address (dd): 00~31
Wiring diagram:
MT8000 RS-232 / 9P D-SUB
HUST CNC Controller
COM1
COM3
RS232 Port
7 TX
8 RX
5 GND
RXD
TXD
GND
3
2
5
COM2
TX
4 TX
RX
6 RX
GND 5 GND
Driver Version:
Version
Date
V1.00
Sep/22/2009
Description of Changes
83
IAI X-SEL
http://www.iai-robot.co.jp/
HMI Setting:
Parameters
Recommend
Option
PLC type
IAI X-SEL Series
Com port
RS485 4W
Baud rate
9600
9600~19200
Parity bit
Even
Even, Odd, None
Data Bits
7 or 8
Stop Bits
1 or 2
HMI Station No.
PLC Station No.
Notes
PLC Setting:
Communication mode
Mode Setting Switch
Parity Check
Sum Check
Device address:
Bit/Word
Device Type
Servo_On_Off
Format
Range
1~8
Memo
Address 1~8 represent the
corresponding axis.
Write 1 means ON and 0 means
OFF.
W
Servo_Origin
1~8
Address 1~8 represent the
corresponding axis.
Back to origin.
RunProgram
Data written indicates which
program to run.
84
EndProgram
Data written indicates which
program to stop.
SoftWareReset
CurrentAxisPos
1~8
Reset soft ware.
For reading current position. The
state of current axis is put in RW
axis*100.
i.e., for the state of axis 2,
2*100=200, so it is in RW200.
PointMove
1~8
Address 1~8 represent the
corresponding axis. The data written
indicates which point to reach. Put
parameters ACC, DEC, SPEED in
axis*100+1, axis*100+2 and
axis*100+3 respectively.
JoggingMove
1~8
Jogging. Address 1~8 represent the
corresponding axis. Put parameters
ACC, DEC, SPEED and Position in
axis*100+11, axis*100+12,
axis*100+13 and axis*100+14
respectively.
AbsoluteMove
1~8
Jog to the set absolute coordinate.
Address 1~8 represent the
corresponding axis. Put parameters
ACC, DEC, SPEED and Position in
axis*100+21, axis*100+22,
axis*100+23 and axis*100+24
respectively.
PointChange
1~8
To change the value of the point.
Address 1~8 represent the
corresponding axis. Put parameters
ACC, DEC, SPEED and Position in
axis*100+31, axis*100+32,
axis*100+33 and axis*100+34
respectively.
Note: ddd: Decimal, hhh: Hexadecimal, ooo: Octal.
Every model of CPU is different; we suggest user to refer to PLC manuals Device List.
85
Wiring diagram:
MT8000 RS232
9P D-SUB
Host RS232
COM1
COM2
COM3
TX
4 TX
7 TX
RX
RX
6 RX
TX
GND
5 GND
5 GND
RX
GND
86
IDEC
IDEC Micro3, Micro3C, MicroSmart, OpenNet Controller series
http://www.idec.com
HMI Setting:
Parameters
Recommend
Option
PLC type
IDEC Micro
Com port
RS232
RS232, RS485
Baud rate
9600
9600, 19200
Parity bit
Even
Even, Odd, None
Data Bits
7, 8
Stop Bits
HMI Station No.
PLC Station No.
255 (for 1:1 connect)
Notes
Support Extend address mode
Does not apply to this protocol
Online Simulator
YES
Extend address mode
YES
0-255
255 or same as the PLC setting
Dont set the PLC Station No.= 255
PLC Setting:
Communication mode
9600,E,7,1(default), Use Computer Link Protocol
Device address:
Bit/Word
Device Type
Format
Range
ddd(o)
ddd=0~2047, (o)=0~7
Input(I)
ddd(o)
ddd=0~2047, (o)=0~7
Output(Q)
ddd(o)
ddd=0~2047, (o)=0~7
Internal Relay(M)
RT
ddd
ddd=0~9999
Timer(T)
RC
ddd
ddd=0~9999
Counter(C)
ddd
ddd=0~9999
Data Register(D)
87
Memo
Wiring diagram:
RS232: Micro3C, MicroSmart, OpenNet Controller CPU Ladder Port
CPU port 1 or port2 RS-232
MT8000 RS232
8P mini DIN Male
COM1
COM2
COM3
3 TX 4 TX 7 TX
2 RX 6 RX 8 RX
5 GND 5 GND 5 GND
4 RXD
3 TXD
7 GND
8Pin mini DIN
Female Pin
Layout
MicroSmart
MT8000
RS232
MT8000
RS485: Micro3 CPU Port, MicroSmart with FC4A-PC2 RS485 Communication Adapter
CPU Port RS-485
MT8000 RS-485
8P mini DIN Male
COM1
1 RX2 RX+
5 GND
COM3
6 Data9 Data+
5 GND
2
1
7
RXDRXD+
GND
RS485: Micro3C, OpenNet Controller Data Link Terminals,
MicroSmart with FC4A-PC3 RS485 Communication Adapter
Data Link Terminals
MT8000 RS-485
9P D-SUB Female
COM1
1 RX2 RX+
5 GND
COM3
6 Data9 Data+
5 GND
A
B
SG
88
RXDRXD+
GND
8Pin mini DIN
Female Pin
Layout
Driver Version:
Version
Date
V1.20
Jun/19/2009
Description of Changes
89
INOVANCE H2U/H1U
http://www.inovance.cn/
HMI Setting:
Parameters
Recommend
Option
PLC type
INOVANCE H2U/H1U
Com port
RS485 4W
Baud rate
9600
9600~19200
Parity bit
Even
Even, Odd, None
Data Bits
7 or 8
Stop Bits
1 or 2
HMI Station No.
PLC Station No.
Notes
PLC Setting:
Communication mode
Mode Setting Switch
Parity Check
Sum Check
Device address:
Bit/Word
Device Type
Format
Range
Memo
ooo
0~377
Input Bits
ooo
0~377
Output Bits
dddd
0~7999
Auxiliary Relay
SM
dddd
8000~9999
ddd
0~255
Timer Relay
ddd
0~255
Counter Relay
TV
ddd
0~255
Timer Memory
CV
ddd
0~199
Counter Memory
DW
CV2
ddd
200~255
Counter Memory (32bit)
dddd
0~7999
Data Registers
SD
dddd
8000~9999
Special Auxiliary Relay
Special Data Register
Note: ddd: Decimal, hhh: Hexadecimal, ooo: Octal.
Every model of CPU is different, we suggest user to refer to PLC manuals Device List.
90
Wiring diagram:
RS-485 4W:
H2U/H1U
MT800 Com1 RS-485]
RS-422 8P Din
9P D-SUB
1
RX-
TX-
RX+
TX+
TX-
RX-
TX+
RX+
GND
GND
91
Intelligent Servo
Intelligent Servo supports IDM640, IDM240.
http://www.techsoftmotion.com
HMI Setting:
Parameters
PLC type
Com port
Baud rate
Parity bit
Data Bits
Stop Bits
HMI Station No.
PLC Station No.
Recommend
Intelligent Servo
RS232
9600
None
8
1
0
1
Option
Notes
9600~115200
Even, Odd, None
7 or 8
1 or 2
PLC Setting:
Communication mode
Device address:
Bit/Word
W
DW
W
W
Device Type
Register_32bit
Register_H
UDP
STOP
Format
hhh
hhh
hhh
hhh
Range
0~9999
0~9999
hhh:0
hhh:0
Memo
32bit signed
32bit Hex
Send UDP command
Send STOP command
Wiring diagram:
MT8000 RS232
9P D-SUB Female
COM1
3
2
5
COM2
TX
4 TX
RX
6 RX
GND 5 GND
Servo(RS232)
COM3
7 TX
8 RX
5 GND
3
2
5
RD
TD
GND
Driver Version:
Version
Date
Description of Changes
92
V1.00
Nov/06/2009
JUSTFI Controller
Justfi weighing instruments, Industrial Batching Controller supports XK31CB4, XK31CB6.
http://www.justfi.com
HMI Setting:
Parameters
PLC type
Com port
Baud rate
Parity bit
Data Bits
Stop Bits
HMI Station No.
PLC Station No.
Recommend
Justfi controller
RS232
9600
Even
7
1
0
1
Option
Notes
9600, 19200
Even, Odd, None
7 or 8
1 or 2
PLC Setting:
Communication mode
Device address:
Bit/Word
W
DW
W
W
Device Type
Func
Func_DW
RW
RF
Format
dd
dd
hhh
hhh
Range
dd:0~99
dd:0~99
hhh:0
hhh:0
Memo
Read/Write
Read/Write
Weight (Read only)
Read result (Read only)
RT
hhh
hhh:0
Read total (Read only)
RG
hhh
hhh:0
Read prescription group
RC
hhh
hhh:0
Circle
RB
hhh
hhh:0
Read Status (Read only)
MZ
hhh
hhh:0
Zero (Write only)
MT
hhh
hhh:0
Tare (Write only)
CT
hhh
hhh:0
Clear tare (Write only)
DT
hhh
hhh:0
Clear total (Write only)
BB
hhh
hhh:0
Start (Write only)
HB
hhh
hhh:0
Stop (Write only)
BD
hhh
hhh:0
Discharge (Write only)
WP1t
.
.
hhh
hhh:0
Read/Write Recipe
93
RP6F
Wiring diagram:
MT8000 RS232
9P D-SUB Female
COM1
3
2
5
COM2
TX
4 TX
RX
6 RX
GND 5 GND
CB4(RS232)
COM3
7 TX
8 RX
5 GND
RD
TD
GND
Driver Version:
Version
Date
V1.00
Nov/04/2009
Description of Changes
94
KERNEL SISTEMI
Kernel systemi DMX 30
http://www.kernel.modena.it/
HMI Setting:
Parameters
Recommend
Option
PLC type
Kernel sistemi
Com port
RS232
RS485
Baud rate
19200
9600
Parity bit
Data Bits
Stop Bits
PLC Station No.
Notes
Must match the PLCs port setting
Device address:
Bit/Word
W
Device Type
Format
hhhh
Range
Memo
0~ffff
Wiring diagram:
MT8000 RS232
9P D-SUB Female
COM1
COM2
COM3
Port2 RS232
9P D-SUB Female
TX
4 TX
7 TX
RX
RX
6 RX
8 RX
TX
5 GND
5 GND
GND
5 GND
Driver Version:
Version
Date
V1.0.0
Feb/04/2010
Description of Changes
95
KEYENCE KV series
KEYENCE KV series, KV10~80
http://www.keyence.com/
HMI Setting:
Parameters
Recommend
Option
PLC type
KEYENCE KV-16
Com port
RS232
Baud rate
9600
Must match the PLCs port setting.
Parity bit
Even
Must match the PLCs port setting.
Data Bits
Stop Bits
PLC Station No.
RS232
Notes
Must match the PLCs port setting.
Must match the PLCs port setting.
PLC Setting:
Communication mode
None
Device address:
Bit/Word
Device Type
Format
Range
RLY
ddd(h)0
0~19999
MR
ddd(h)
0~19999
LR
ddd(h)
0~19999
CR
ddd(h)
0~19999
DM_Bit
ddd(h)
0~19999
DM
ddd
0-1999
TM
ddd
0-99
CM
ddd
0~65535
EM
ddd
0~65535
ddd
0-999
Timer_Curr
ddd
0-999
Timer_Preset
ddd
0-999
ddd
0-999
Counter_Curr
ddd
0-999
Counter_Preset
ddd
0-999
Precaution:
96
Memo
Timer_Current
Counter_Current
If you use the Relay(bit) register, Please place zero behind address.For example, If you want to read Relay(bit)100,
you just set the address as 1000.
Wiring diagram:
RS232: CPU port
MT8000 RS-232 9P D-SUB
COM1
COM2
KEYENCE PLC
COM3
OP-26486
TX
TX
TX
RXD
RX
RX
RX
TXD
GND
GND
GND
GND
Driver Version:
Version
Date
V1.30
Apr/17/2009
Description of Changes
97
KEYENCE KV-1000
http://www.keyence.com/
HMI Setting:
Parameters
Recommend
Option
PLC type
KEYENCE KV-1000
Com port
RS232
Baud rate
9600
Must match the PLCs port setting.
Parity bit
Even
Must match the PLCs port setting.
Data Bits
Stop Bits
PLC Station No.
RS232
Notes
Must match the PLCs port setting.
Must match the PLCs port setting.
PLC Setting:
Communication mode
None
Device address:
Bit/Word
Device Type
Format
Range
RLY
ddd(h)0
0~19999
MR
ddd(h)
0~19999
LR
ddd(h)
0~19999
CR
ddd(h)
0~19999
DM_Bit
ddd(h)
0~19999
DM
ddd
0-1999
TM
ddd
0-99
CM
ddd
0~65535
EM
ddd
0~65535
ddd
0-999
Timer_Curr
ddd
0-999
Timer_Preset
ddd
0-999
ddd
0-999
Counter_Curr
ddd
0-999
Counter_Preset
ddd
0-999
98
Memo
Timer_Current
Counter_Current
Precaution:
If you use the Relay(bit) register, Please place zero behind address.For example, If you want to read Relay(bit)100,
you just set the address as 1000.
Wiring diagram:
RS232: CPU port
MT8000 RS-232 9P D-SUB
COM1
COM2
KEYENCE PLC
COM3
OP-26486
TX
TX
TX
RXD
RX
RX
RX
TXD
GND
GND
GND
GND
Driver Version:
Version
Date
V2.20
Jul/28/2009
Description of Changes
99
KEYENCE KV-5000 (Ethernet)
http://www.keyence.com/
HMI Setting:
Parameters
Recommend
Option
Notes
PLC type
KEYENCE KV-5000 (Ethernet)
Com port
Ethernet
PLC IP
192.168.0.10
Must match the PLCs port setting.
TCP port
8501
Must match the PLCs port setting.
PLC Station No.
Must match the PLCs port setting.
PLC Setting:
Communication
mode
None
Device address:
Bit/Word
Device Type
Format
Range
Memo
RLY
ddd(h)0
0-19999
MR
ddd(h)
0-19999
LR
ddd(h)
0-19999
CR
ddd(h)
0-19999
DM
ddd
0-1999
TM
ddd
0-99
CM
ddd
0- 65535
EM
ddd
0- 65535
ddd
0-999
Timer_Curr
ddd
0-999
Timer Current
Timer_Preset
ddd
0-999
Timer Preset
ddd
0-999
Counter_Current
ddd
0-999
Counter_Preset
ddd
0-999
Precaution:
If you use the RLY(bit) register, Please place zero behind address.
For example, If you want to read RLY 100, you just set the address as 1000.
100
Wiring diagram:
Ethernet:
MT8000 Ethernet
RJ45
Wire color
Ethernet Hub or Switch
RJ45
TX+
White/Orange
RX+
TX-
Orange
RX-
RX+
White/Green
TX+
BD4+
Blue
BD4+
BD4-
White/Blue
BD4-
RX-
Green
TX-
BD3+
White/Brown
BD3+
BD3-
Brown
BD3-
Ethernet: Direct connect (crossover cable)
MT8000 Ethernet
RJ45
Wire color
KV-5000 Ethernet
RJ45
TX+
White/Orange
RX+
TX-
Orange
RX-
RX+
White/Green
TX+
BD4+
Blue
BD4+
BD4-
White/Blue
BD4-
RX-
Green
TX-
BD3+
White/Brown
BD3+
BD3-
Brown
BD3-
Driver Version:
Version
Date
V1.00
Dec/25/2009
Description of Changes
101
RJ45
connector
Korenix 6550 / 6520
http://www.korenix.com/
HMI Setting:
Parameters
Recommend
PLC type
Korenix 6550/ 6520
COM port
Ethernet
Option
Notes
Modbus protocol
PLC station No.
Port No.
502
Device address:
Bit/Word
Device type
Format
Range
3X
ddddd
1~65535
4X
ddddd
1~65535
5X
ddddd
1~65535
6X
ddddd
1~65535
0X
ddddd
1~65535
1X
ddddd
1~65535
3x_Bit
ddddd
1~65535
4x_Bit
ddddd
1~65535
6x_Bit
ddddd
1~65535
102
Memo
Wiring diagram:
Ethernet:
MT8000 Ethernet Wire color
RJ45
Ethernet Hub or
Switch RJ45
1
2
3
TX+
TXRX+
White/Orange
Orange
White/Green
1
2
3
RX+
RXTX+
4
5
6
7
8
BD4+
BD4RXBD3+
BD3-
Blue
White/Blue
Green
White/Brown
Brown
4
5
6
7
8
BD4+
BD4TXBD3+
BD3-
Ethernet: Direct connect (crossover cable)
MT8000 Ethernet Wire color
Modbus TCP Device
RJ45
RJ45
1
2
3
TX+
TXRX+
White/Orange
Orange
White/Green
3
6
1
RX+
RXTX+
4
5
6
7
8
BD4+
BD4RXBD3+
BD3-
Blue
White/Blue
Green
White/Brown
Brown
4
5
2
7
8
BD4+
BD4TXBD3+
BD3-
Driver Version:
Version
Date
V1.61
Apr/17/2009
Description of Changes
103
8
RJ45
KOYO CLICK PLC Series
KOYO CLICK PLC series
http://www.automationdirect.com
HMI Setting:
Parameters
Recommend
Option
Notes
PLC type
CLICK
Com port
RS232
Baud rate
38400
Communications Port1 (fixed)
Reference PLC Specification
Parity bit
Odd
Communications Port1 (fixed)
Reference PLC Specification
Data Bits
Communications Port1 (fixed)
Reference PLC Specification
Stop Bits
Communications Port1 (fixed)
Reference PLC Specification
PLC Station No.
Communications Port1 (fixed)
Reference PLC Specification
Device address:
Bit/Word
Device Type
Format
Range
d(dd)
001 ~ 816
Input Status (Read Only)
d(dd)
001 ~ 816
Output Status
dddd
1 ~ 2000
Control Bit
ddd
1 ~ 500
Timer Status (Read Only)
CT
ddd
1 ~ 250
Counter Status (Read Only)
SC
dddd
1 ~ 1000
System Control Bit (Read Only)
DS
dddd
1 ~ 4500
Data Registers
DD
dddd
1 ~ 1000
Data Registers (Double word)
DH
dddd
1 ~ 500
Data Registers
DF
dddd
1 ~ 500
Data Registers (Double word)
XD
0~8
Input Status Registers (Read Only)
YD
0~8
Output Status Registers
TD
ddd
1 ~ 500
CTD
ddd
1 ~ 250
SD
dddd
1 ~ 1000
TXT
dddd
1 ~ 1000
ddd: Decimal / hhh:Hexadecimal / ooo:Octal
104
Memo
Timer Current Values (Read Only)
Counter Current Values (Double
word/Read Only)
System Data Registers (Read Only)
Text Data Registers
Wiring diagram:
KOYO CLICK PLC Com Port:
RS-232: KOYO CLICK PLC
EasyView MT8000
KOYO CLICK PLC RS-232 6
9P D-SUB
Pin RJ12 Jack
COM1[RS232]
COM2[RS232]
COM3[RS232]
TX
TX
TX
RXD
RX
RX
RX
TXD
GND
GND
GND
GND
Driver Version:
Version
Date
V1.20
Oct/20/2009
V1.10
Apr/17/2009
Description of Changes
Fixed the bit addresses X, Y and word addresses XD, YD are not
able to read/write correctly.
105
KOYO DirectLogic
KOYO DirectLogic series PLC DL05, DL06DL105, DL205, DL305 and DL405 series
http://www.automationdirect.com
HMI Setting:
Parameters
Recommend
Option
PLC type
KOYO DIRECT
Com port
RS232
RS232, RS485
Baud rate
9600
9600, 19200, 38400
Parity bit
Odd
Even, Odd, None
Data Bits
7, 8
Stop Bits
HMI Station No.
PLC Station No.
Notes
Does not apply to this protocol.
1-90
PLC Setting:
1.
The PLC must not have a password.
2.
PLC must be set for Full Duplex operation.
3.
PLC must be set for No Hardware Handshaking.
4.
The PLC must be set to use the K Sequence Protocol.
5.
Set the mode switch to the TERM mode
6.
When using the D4-440 CPU, you must set the station number to 1.
Device address:
Bit/Word
Device Type
Format
Range
oooo
0 ~ 4000
Input Bits
oooo
0 ~ 4000
Output Bits
ooooo
0 ~ 10000
Control Relays
oooo
0 ~ 1000
Timer Status Bits
CT
oooo
0 ~ 1000
Counter Status Bits
oooo
0 ~ 2000
SP
oooo
0 ~ 2000
GX
ooooo
0 ~ 10000
106
Memo
GY
ooooo
0 ~ 10000
Timer
oooo
0 ~ 1000
Counter
oooo
0 ~ 1000
oooo
0 ~ 77777
V Memory
Wiring diagram:
1. CPU unit: DL05/DL06/DL105/DL230/DL240/DL250/DL350/DL450 RS232 port
MT8000 RS232
KOYO DirectLogic PLC
RS232 port
9P D-SUB
6P RJ12 phone jack
COM1
COM2
3 TX
4 TX
2 RX
6 RX
5 GND 5 GND
COM3
7 TX
8 RX
5 GND
3 RX
4 TX
1 GND
RJ12 6Pin
Female
2. CPU unit: DL06/DL250 CPU Port2 RS232
MT8000 RS232
KOYO DirectLogic PLC
9P D-SUB
CPU RS232 Port2
15P D-SUB Female
COM1
COM2
COM3
3 TX
2 RX
5 GND
4 TX
6 RX
5 GND
7 TX
8 RX
5 GND
3
2
7
4
5
RX
TX
GND
RTC
CTS
3. CPU unit: DL06/DL250 CPU Port2 RS422
MT8000
KOYO DirectLogic PLC
COM1 [RS-485] 4w
CPU RS422 Port2
15P D-SUB Female
9P D-SUB
1
2
5
3
4
RXRX+
GND
TXTX+
10
9
7
6
13
11
14
12
15
Note: DL06/DL250 CPU Port2 include RS232 and RS422
107
TXTX+
GND
RXRX+
RTS+
CTS+
RTSCTS-
15P D-SUB Female
108
4. CPU unit: DL430/DL440/DL450 CPU unit Port0 RS232
MT8000 RS232
KOYO DirectLogic PLC
9P D-SUB
DL405 CPU RS232 Port0
15P D-SUB Female
COM1
COM2
COM3
3 TX
2 RX
5 GND
4 TX
6 RX
5 GND
7 TX
8 RX
5 GND
3
RX
2
TX
13 GND
1
YOP
7
CTS
2
YOM
4
ONLINE
14 GND
5. CPU unit: DL430/DL440/DL450 CPU unit Port1 & DL350 CPU unit Port2 RS232
MT8000 RS232
KOYO DirectLogic PLC
9P D-SUB
DL305/405 CPU RS232 Port
25P D-SUB Female
COM1
COM2
COM3
3 TX
2 RX
5 GND
4 TX
6 RX
5 GND
7 TX
8 RX
5 GND
3
2
7
4
5
RX
TX
GND
RTC
CTS
6. CPU unit: DL430/DL440/DL450 CPU unit Port1 & DL350 CPU unit Port2 RS422
MT8000
KOYO DirectLogic PLC
COM1[RS-485]4w
DL305/405 CPU RS422 Port
25P D-SUB Female
9P D-SUB
1
2
5
3
4
16
14
7
10
9
19
11
18
23
RXRX+
GND
TXTX+
109
TXTX+
GND
RXRX+
RTS+
CTS+
RTSCTS-
7. CPU unit: DL450 CPU unit Port3 RS422
MT8000
KOYO DirectLogic PLC
COM1[RS-485]4w
DL405 CPU RS422 Port3
25P D-SUB Female
9P D-SUB
1
2
5
3
13
TX12
TX+
7
GND
25
RX24 RX+
RXRX+
GND
TX4 TX+
8. Communication unit: DL205 series D2-DCM and DL405 series D4-DCM RS232
KOYO DirectLogic PLC
MT8000 RS232
DL205/405 DCM RS232 Port
9P D-SUB
25P D-SUB Female
COM1
COM2
COM3
3 TX
2 RX
5 GND
4 TX
6 RX
5 GND
7 TX
8 RX
5 GND
3
2
7
4
5
RX
TX
GND
RTC
CTS
Driver Version:
Version
Date
V1.20
Dec/30/2008
Description of Changes
110
KOYO DirectLogic Ethernet Module
KOYO DirectLogic series, model H0-ECOM100
http://www.automationdirect.com
HMI Setting:
Parameters
Recommend
PLC type
KOYO ETHERNET
Com port
Ethernet, UDP/IP
PLC Station No.
No need to set station no.
TCP/IP port
28784
Option
Notes
Device address:
Bit/Word
Device Type
Format
Range
Memo
GX
oooo
0~3777
Global I/O
oooo
0~1777
Real Word Inputs
SP
oooo
0~1777
Special Purpose Relays
GY
oooo
0-3777
More Global I/O
oooo
0-1777
Real Word Outputs
oooo
0-3777
Control Relays
ooo
0-1777
Stage Status Bits
ooo
0-377
Timer Status Bits
CT
ooo
0-377
Counter Status Bits
ooooo
0-41237
V-memory
CMM_32
hhh
001-200
GX, X, SP
CCM_33
hhh
001-340
GY,Y,C,S,Y,CT,V
CCM_31
hhhh
1-42A0
EB8000 device addresses range may different with PLC extended mode, please refer EB8000s
addresses range as above.
ddd:Decimal, hhh:Hexadecimal, ooo:Octal
111
Wiring diagram:
Ethernet port
MT8000 Ethernet Wire color
RJ45
Ethernet Hub or
Switch RJ45
1
2
3
TX+
TXRX+
White/Orange
Orange
White/Green
1
2
3
RX+
RXTX+
4
5
6
7
8
BD4+
BD4RXBD3+
BD3-
Blue
White/Blue
Green
White/Brown
Brown
4
5
6
7
8
BD4+
BD4TXBD3+
BD3-
Ethernet: Direct connect (crossover cable)
MT8000 Ethernet Wire color
Modbus TCP Device
RJ45
RJ45
1
2
3
TX+
TXRX+
White/Orange
Orange
White/Green
3
6
1
RX+
RXTX+
4
5
6
7
8
BD4+
BD4RXBD3+
BD3-
Blue
White/Blue
Green
White/Brown
Brown
4
5
2
7
8
BD4+
BD4TXBD3+
BD3-
Driver Version:
Version
Date
V1.10
Jul/03/2009
Description of Changes
112
Lenze
PLC Model No. : 9300/8200 series
Pass-through 2102IB fieldbus module:RS485(LECOM B)
http://www.lenze.de
HMI Setting:
Parameters
Recommend
Option
Notes
PLC type
Lenze
Com port
RS485
RS485
Baud rate
9600
9600, 19200
Parity bit
Even
Even, Odd, None
Data Bits
7,8
Stop Bits
1, 2
HMI Station No.
0-255
PLC Station No.
0-255
PLC Setting:
Communication mode
Same as the MT500 setting
Device address:
Bit/Word
Device Type
Format
Range
B
W
W
W
W
W
W
CNB
CI
CD
CF
CNI
CND
CNF
ddd(dd)
ddd
ddd
ddd
0-999915
0-819200
0-819200
0-819200
0-9999
0-9999
0-9999
ddd
ddd
ddd
Memo
integer
DWord
DWord(float point)
Wiring diagram:
EasyView MT8000 HMI
Lenze 2102IB LECOM-B
RS485 9 Pin D-SUB
RS485 Plug-in terminal 4-pole
COM1
COM3
1
2
6
9
RXRX+
DataData+
72
71
113
T/R(A)
T/R(B)
Driver Version:
Version
Date
V1.10
Apr/17/2009
Description of Changes
114
LS GLOFA Cnet
LS GLOFA GM6/GM7 CPU port. G7L-CUEB / G6L-CUEB / G4L-CUEA / G3L-CUEA Cnet
module.
http://www.lgis.com/
HMI Setting:
Parameters
Recommend
Option
Notes
PLC type
LS GLOFA Cnet
Com port
RS232
RS232/RS485 2W/4W
Baud rate
9600
9600~115200
Parity bit
None
Even, Odd, None
Data Bits
7, 8
Stop Bits
HMI Station No.
PLC Station no.
0~31
PLC Setting:
Communication mode
9600,N,8,1(default), Cnet protocol
Communication module
Applicable mode: 1 Dedicated communication
Device address:
Bit/Word
Device Type
Format
Range
Memo
IX
hhhh(dd)
0~270F15
Input
QX
hhhh(dd)
0~270F15
Output
MX
ddddd
0~32767
Internal relay
MW
ddddd
0~32767
Data register
DW
MD
ddddd
0~16383
Double word
d:(Decimal)
h:(Hexadecimal)
Wiring diagram:
RS-232:
MT8000 RS232
9P D-SUB
LG GLOFA GM
CPU port
RS232 9P D-SUB
COM1
COM2
COM3
TX
4 TX
7 TX
RXD
RX
6 RX
TXD
GND
5 GND
5 GND
GND
RX
115
RS-232: Communication Module( G7L-CUEB / G6L-CUEB / G4L-CUEA / G3L-CUEA Cnet
RS232 )
MT8000 RS232
9P D-SUB
LG GLOFA GM
RS232 9P D-SUB
COM1
COM2
COM3
TX
4 TX
7 TX
RXD
RX
6 RX
TXD
GND
5 GND
5 GND
GND
CD
RTS
CTS
DTR
DSR
RX
RS485 4wire: Communication Module( G7L-CUEC / G6L-CUEC / G4L-CUEA / G3L-CUEA
Cnet RS422 )
RS422 port
MT8000
COM1[RS-485]4w
9P D-SUB
1
RX-
SDA
RX+
SDB
TX-
RDA
TX+
RDB
GND
GND
Driver Version:
Version
Date
V1.60
Apr/16/2009
Description of Changes
116
LS GLOFA GM3 GM4 GM6 GM7 (Loader)
LS GLOFA series GM3, GM4, GM6, GM7 CPU port
http://www.lgis.com/
HMI Setting:
Parameters
Recommend
PLC type
LS GLOFA GM3467(LOADER)
Com port
RS-232
Option
Notes
PLC Station no.
Baud rate
38400
Data bit
Parity bit
Stop bit
Device address:
Bit/Word
Device Type
Format
Range
MX
ddddd
IX
dd.D.dd
00000~63763
QX
dd.D.dd
00000~63763
MW
dddd
0~32767
MD
ddddd
0~16383
Memo
0~524272
00.0.0 ~63.7.63
(dd.D.dd)
00.0.0 ~63.7.63
(dd.D.dd)
Wiring diagram:
RS-232:
LS GLOFA series
RS-232
9P D-SUB Female
MT8000 RS232
9P D-SUB Female
COM1
COM2
COM3
TX
TX
TX
RD
RX
RX
RX
TD
GND
GND
GND
GND
117
Driver Version:
Version
Date
V1.20
Feb/11/2010
Description of Changes
Modify the addressing
118
LS MASTER-K Cnet
LS MASTER-K series: K80S, K200S, K300S, K1000S
http://www.lgis.com/
HMI Setting:
Parameters
Recommend
PLC type
LS MASTER-K Cnet
Com port
RS232
RS232/RS485
Must match the PLCs port setting.
Baud rate
38400
9600, 19200, 38400
Must match the PLCs port setting.
Parity bit
None
Even, Odd, None
Must match the PLCs port setting.
Data Bits
Must match the PLCs port setting.
Stop Bits
Must match the PLCs port setting.
HMI Station No.
PLC Station No.
Online Simulator
Option
Notes
Does not apply to this protocol.
0-31
Must match the PLCs port setting.
YES
Extend address mode
PLC Setting:
Communication mode
38400, None, 8, 1
Device address:
Bit/Word
Device
Type
Format
Range
Memo
ddd(h)
0~255F
I/O Relay (P)
ddd(h)
0~255F
Keep Relay (K)
ddd(h)
0~255F
Auxiliary Relay (M)
ddd(h)
0~255F
Link Relay (L)
ddd(h)
0~255F
Special Relay (F)
TV
ddd
0~255
Timer Present Value
CV
ddd
0~255
Counter Present Value
dddd
0~9999
Data Register (D)
d: Decimal h: Hexadecimal
119
Wiring diagram:
COM1
MT8000 RS232
CPU port Cnet I/F
9P D-SUB
RS232
9P D-SUB Female
COM2
COM3
4 RX
3 TX 4 TX 7 TX
7 TX
2 RX 6 RX 8 RX
5 GND
5 GND 5 GND 5 GND
If connect with Cnet module please refer Cnet modules document.
Driver Version:
Version
Date
V1.00
Dec/30/2008
Description of Changes
120
LS MASTER-K10S1
LS MASTER-K10S1
http://www.lgis.com/
HMI Setting:
Parameters
Recommend
Option
Notes
PLC type
LS MASTER-K10S1
Com port
RS232
RS232/RS485
Must match the PLCs port setting.
Baud rate
9600
Parity bit
None
None
Must match the PLCs port setting.
Data Bits
Must match the PLCs port setting.
Stop Bits
Must match the PLCs port setting.
HMI Station No.
Does not apply to this protocol.
PLC Station No.
Must match the PLCs port setting.
Must match the PLCs port setting.
PLC Setting:
Communication
mode
9600, None, 8, 1
Select
Device address:
Bit/Word
Device
Type
Format
Range
Memo
ddd(h)
0~255F
I/O Relay (P)
ddd(h)
0~255F
Keep Relay (K)
ddd(h)
0~255F
Auxiliary Relay (M)
ddd(h)
0~255F
Link Relay (L)
ddd(h)
0~255F
Special Relay (F)
ddd
0~255
Timer (T)
ddd
0~255
Counter (C)
TV
ddd
0~255
Timer Present Value
CV
ddd
0~255
Counter Present Value
dddd
0~9999
Data Register (D)
121
d: Decimal h: Hexadecimal
Wiring diagram:
MT8000 RS232
CPU port RS232
9P D-SUB
9P D-SUB Female
COM1
3 TX
2 RX
5 GND
COM2
4 TX
6 RX
5 GND
COM3
7 TX
8 RX
5 GND
RX
TX
GND
Driver Version:
Version
Date
V1.00
Sep/08/2009
Description of Changes
122
LS MASTER-K300S CPU
LS MASTER-K series: K80S, K120S, K200S, K300S, K1000S
http://www.lgis.com/
HMI Setting:
Parameters
Recommend
PLC type
LG MASTER-K300S
Com port
RS232
RS232/RS485
Must match the PLCs port setting.
Baud rate
38400
9600, 19200, 38400
Must match the PLCs port setting.
Parity bit
None
Even, Odd, None
Must match the PLCs port setting.
Data Bits
Must match the PLCs port setting.
Stop Bits
Must match the PLCs port setting.
HMI Station No.
PLC Station No.
Online Simulator
Option
Notes
Does not apply to this protocol.
0-31
Must match the PLCs port setting.
YES
Extend address mode
PLC Setting:
Communication
38400, None, 8, 1
mode
Device address:
Bit/Word
Device
Type
Format
Range
ddd(h)
0~255F
I/O Relay (P)
ddd(h)
0~255F
Keep Relay (K)
ddd(h)
0~255F
Auxiliary Relay (M)
ddd(h)
0~255F
Link Relay (L)
ddd(h)
0~255F
Special Relay (F)
TV
ddd
0~255
Timer Present Value
CV
ddd
0~255
Counter Present Value
dddd
0~9999
Data Register (D)
123
Memo
d: Decimal h: Hexadecimal
Wiring diagram:
COM1
MT8000 RS232
CPU port RS232
9P D-SUB
9P D-SUB Female
COM2
3 TX
4 TX
2 RX
6 RX
5 GND 5 GND
COM3
7 TX
8 RX
5 GND
2 RX
3 TX
5 GND
Driver Version:
Version
Date
V1.10
Dec/30/2008
Description of Changes
124
LS XGB/XGT
LS XGB/XGT Series
http://www.lgis.com/
HMI Setting:
Parameters
Recommend
Option
Notes
PLC type
LS XGB/XGT
Com port
RS232
RS232/RS485
Must match the PLCs port setting.
Baud rate
115200
9600~115200
Must match the PLCs port setting.
Parity bit
None
Even, Odd, None
Must match the PLCs port setting.
Data Bits
7, 8
Must match the PLCs port setting.
Stop Bits
Must match the PLCs port setting.
HMI Station No.
PLC Station No.
0-31
Must match the PLCs port setting.
Device address:
Bit/Word
Device Type
Format
Range
ddd(h)
0~127F
I/O device_2,048 points
ddd(h)
0~255F
Internal device_4,096 points
dddd(h)
0~1279F
Communication device_20,480 points
dddd(h)
0~2559F
Preservation device_4,096 points
ddd(h)
0~255F
Special device_4,096 point
ddd
0~255
Timer device_256 point
ddd
0~255
Counter device_256 point
ddd(dd)
0~127(99)
D_Bit
dddd(h)
0~5120F
Data register_Bit expression (D0000.0)
dh:0~3f
XGK-CPUE:hh(0~1f)
U_Bit
dh.dd(h)
Memo
Relay for step control
dd:0~31
(h):0~f
dddd
0~5119
d(dd)
0~7(0~31)
dddd
0~3935
Communication data register_3,936 words
ddd
0~127
Index register_128 words
ddd
0~255
Timer current value register_256 words
125
Data register_5120 words
Analog data register_256 words
d:Decimal
ddd
0~255
Counter current value register_256 words
h:Hexadecimal
Wiring diagram:
RS-232:
6pin female pinout
MT8000 RS232
9P D-SUB
COM1
3
2
5
COM2
TX
4 TX
RX
6 RX
GND 5 GND
XGB main unit
RS232 6pin
COM3
7 TX
8 RX
5 GND
RXD
TXD
GND
Driver Version:
Version
Date
V1.30
Apr/17/2009
Description of Changes
126
LS XGB/XGT FEnet (Ethernet)
LS XGB/XGT with XBL-EMTA
http://www.lgis.com/
HMI Setting:
Parameters
Recommend
PLC type
LS XBB/XGT FEnet
Com port
Ethernet
PLC Station no.
TCP/IP port
2004
Option
Notes
0~255
PLC Setting:
Communication mode
FEnet Potocol
Device address:
Bit/Word
Device Type
Format
Range
Memo
ddd(h)
0~127F
I/O device_2,048 points
ddd(h)
0~255F
Internal device_4,096 points
dddd(h)
0~1279F
Communication device_20,480 points
dddd(h)
0~2559F
Preservation device_4,096 points
ddd(h)
0~255F
Special device_4,096 point
ddd
0~255
Timer device_256 point
ddd
0~255
Counter device_256 point
ddd(dd)
0~127(99)
D_Bit
dddd(h)
0~5120F
Relay for step control
Data register_Bit expression (D0000.0)
dh:0~3f
B
U_Bit
dh.dd(h)
dd:0~31
(h):0~f
dddd
0~5119
d(dd)
0~7(0~31)
dddd
0~3935
Communication data register_3,936 words
ddd
0~127
Index register_128 words
ddd
0~255
Timer current value register_256 words
127
Data register_5120 words
Analog data register_256 words
d:(Decimal)
ddd
0~255
Counter current value register_256 words
h:(Hexadecimal)
Wiring diagram:
Ethernet:
MT8000 Ethernet
Wire color
Ethernet Hub or Switch
RJ45
RJ45
TX+
White/Orange
RX+
TX-
Orange
RX-
RX+
White/Green
TX+
BD4+
Blue
BD4+
BD4-
White/Blue
BD4-
RX-
Green
TX-
BD3+
White/Brown
BD3+
BD3-
Brown
BD3-
Ethernet: Direct connect (crossover cable)
Wire color
MT8000
TCP Device
Ethernet RJ45
RJ45
TX+
White/Orange
RX+
TX-
Orange
RX-
RX+
White/Green
TX+
BD4+
Blue
BD4+
BD4-
White/Blue
BD4-
RX-
Green
TX-
BD3+
White/Brown
BD3+
BD3-
Brown
BD3-
Driver Version:
Version
Date
V1.20
Apr/17/2009
Description of Changes
128
8
RJ45
LS XGL-CH2A Cnet
LS XGT series communication module XGL-CH2A
http://www.lgis.com/
HMI Setting:
Parameters
Recommend
Option
PLC type
LS XGL-CH2A Cnet
Com port
RS232
RS232/RS485 2W/4W
Baud rate
19200
9600~115200
Parity bit
None
Even, Odd, None
Data Bits
7, 8
Stop Bits
HMI Station No.
PLC Station no.
Notes
PLC Setting:
Communication mode
Device address:
Bit/Word
Device Type
Format
Range
Memo
dddd(h)
0~2047F
I/O device
dddd(h)
0~2047F
Internal device
dddd(h)
0~2047F
Communication device
dddd(h)
0~2047F
Preservation device
dddd(h)
0~2047F
Special device( write available from 1025)
dddd
0~2047
Timer device
dddd
0~2047
Counter device
ddd(dd)
0~127(99)
Relay for step control
D_Bit
dddd(h)
Data register_Bit expression (D0000.0)
U_Bit
dh.dd(h)
0~19999F
hh:0~3f, dd:0~31
(h):0~f
dddd
0~19999
Data register
hh(dd)
0~3f(0~31)
Analog data register XGK-CPUE : hh(0~1f)
dddd
0~21503
Communication data register
ddd
0~127
Index register_128 words
dddd
0~2047
Timer current value register
dddd
0~2047
Counter current value register
ddddd
0~32767
ZR
ddddd
0~32767
129
XGK-CPUE : hh(0~1f)
Bit/Word
Device Type
Format
Range
Memo
TS
dddd
0~2047
Setup value
CS
dddd
0~2047
Setup value
d:(Decimal)
h:(Hexadecimal)
Wiring diagram:
RS-232:
MT8000 RS232
9P D-SUB
XGL-CH2A
CH1
RS232 9P D-SUB
COM1
COM2
COM3
TX
4 TX
7 TX
RXD
RX
6 RX
TXD
GND
5 GND
GND
GND
RX
RS485 4wire:
XGL-CH2A
MT8000
CH2
COM1[RS-485]4w
5P terminal.
9P D-SUB
1
RX-
TX-
RX+
TX+
TX-
RX-
TX+
RX+
GND
GND
Driver Version:
Version
Date
V1.20
Nov/30/2009
Description of Changes
130
LS XGL-EFMT Fenet (Ethernet)
LS XGT series XGL-EFMT Ethernet module.
http://www.lgis.com/
HMI Setting:
Parameters
Recommend
Option
PLC type
LS XGL-EFMT FEnet (Ethernet)
Com port
Ethernet
Port no.
2004
HMI Station No.
PLC Station no.
Notes
PLC Setting:
Communication mode
Device address:
Bit/Word
Device Type
Format
Range
Memo
dddd(h)
0~2047F
I/O device
dddd(h)
0~2047F
Internal device
dddd(h)
0~2047F
Communication device
dddd(h)
0~2047F
Preservation device
dddd(h)
0~2047F
Special device( write available from 1025)
dddd
0~2047
Timer device
dddd
0~2047
Counter device
ddd(dd)
0~127(99)
Relay for step control
D_BIT
dddd(h)
Data register_Bit expression (D0000.0)
U_BIT
dh.dd(h)
dddd
0~32767F
dh:0~3f, dd:0~31
(h):0~f
0~19999
hh(dd)
0~3f(0~31)
Analog data register XGK-CPUE : hh(0~1f)
dddd
0~21503
Communication data register
ddd
0~127
Index register_128 words
dddd
0~2047
Timer current value register
131
XGK-CPUE : hh(0~1f)
Data register
Bit/Word
Device Type
Format
Range
Memo
dddd
0~2047
Counter current value register
ddddd
0~32767
ZR
ddddd
0~32767
d:(Decimal)
h:(Hexadecimal)
Wiring diagram:
Ethernet:
MT8000 Ethernet Wire color
RJ45
1
TX+
White/Orange
Ethernet Hub or
Switch RJ45
RX+
1
TX-
Orange
RX+
White/Green
TX+
BD4+
Blue
BD4+
BD4-
White/Blue
BD4-
RX-
Green
TX-
BD3+
White/Brown
BD3+
BD3-
Brown
BD3-
RXRJ45
Ethernet: Direct connect (crossover cable)
MT8000 Ethernet Wire color
RJ45
XGL-EFMT
RJ45
TX+
White/Orange
RX+
TX-
Orange
RX-
RX+
White/Green
TX+
BD4+
Blue
BD4+
BD4-
White/Blue
BD4-
RX-
Green
TX-
132
BD3+
White/Brown
BD3+
BD3-
Brown
BD3-
Driver Version:
Version
Date
V1.20
Nov/30/2009
Description of Changes
133
LS XGT/XGK CPU DIRECT
LS XGT/XGK CPU RS232 port
http://www.lgis.com/
HMI Setting:
Parameters
Recommend
Option
PLC type
LS XGT/XGK CPU DIRECT
Com port
RS232
RS232/RS485
Baud rate
19200
9600~115200
Parity bit
None
Even, Odd, None
Data Bits
7, 8
Stop Bits
HMI Station No.
PLC Station no.
Notes
PLC Setting:
Communication mode
Device address:
Bit/Word
Device Type
Format
Range
Memo
dddd(h)
0~2047F
I/O device
dddd(h)
0~2047F
Internal device
dddd(h)
0~2047F
Communication device
dddd(h)
0~2047F
Preservation device
dddd(h)
0~2047F
Special device( write available from 1025)
dddd
0~2047
Timer device
dddd
0~2047
Counter device
ddd(dd)
0~127(99)
Relay for step control
D_Bit
dddd(h)
Data register_Bit expression (D0000.0)
U_Bit
hhdd(h)
0~19999F
hh:0~3f, dd:0~31
(h):0~f
dddd
0~19999
Data register
hh(dd)
0~3f(0~31)
Analog data register XGK-CPUE : hh(0~1f)
dddd
0~21503
Communication data register
ddd
0~127
Index register_128 words
dddd
0~2047
Timer current value register
dddd
0~2047
Counter current value register
ddddd
0~32767
134
XGK-CPUE : hh(0~1f)
ZR
ddddd
0~32767
TS
dddd
0~2047
Setup value
CS
dddd
0~2047
Setup value
d:(Decimal)
h:(Hexadecimal)
Wiring diagram:
RS-232:
MT8000 RS232
9P D-SUB
XGT main unit
RS232 9P D-SUB
COM1
COM2
COM3
TX
TX
TX
RXD
RX
RX
RX
TXD
GND
GND
GND
GND
Driver Version:
Version
Date
V1.00
Nov/30/2009
Description of Changes
135
LIYAN EX series
LIYAN PLC Ex/Ex1s/Ex1n/Ex2n series
http://www.liyanplc.com/
HMI Setting:
Parameters
PLC type
Com port
Baud rate
Parity bit
Data Bits
Stop Bits
HMI Station No.
PLC Station No.
Recommend
Mitsubishi FX0n/FX2
RS232
9600
Even
7
1
0
0
Option
RS232
9600~115200
Even, Odd, None
7,8
1,2
0-255
0-255
Notes
Must match the PLCs port setting.
Must match the PLCs port setting.
Must match the PLCs port setting.
Must match the PLCs port setting.
Must match the PLCs port setting.
Does not apply to this protocol.
Must match the PLCs port setting.
PLC Setting:
Communication mode
9600,7,1,Even
Device address:
Bit/Word
B
B
B
B
B
W
W
W
W
W
Device
Type
X
Y
M
T
C
TV
CV
D
CV2
SD
Format
Range
ooo
ooo
ddd
ddd
ddd
ddd
ddd
ddd
ddd
ddd
0-377
0-377
0-9999
0-255
0-255
0-255
0~199
0-9999
200-255
8000-9999
136
Memo
Input relay
Output relay
Internal bit memory
Timer bit memory
Counter bit memory
Timer register
Counter Register
data Register
Counter Register(Double word)
Special data register
Wiring diagram:
Ex,Ex1s,Ex1n,Ex2n series RS232
LIYAN Ex series
CPU RS232 Port
8P miniDin Female
MT8000 RS232
9P D-SUB
COM1
COM2
COM3
TX
4 TX
7 TX
RXD
RX
6 RX
8 RX
TXD
5 GND
5 GND
GND
5 GND
Driver Version:
Version
Date
V1.10
Aug/12/2009
Description of Changes
137
8Pin miniDin
Female
Master (Master-Slave Protocol)
To connect MT8000 with MT500, MT500 has to set as [Slave].
HMI Setting:
Parameters
Recommend
PLC type
Master (Master-Slave
Option
Notes
Protocol)
Com port
RS232
Baud rate
115200
Parity bit
Even
Data Bits
Stop Bits
HMI Station No.
PLC Station No.
Parameter 1
MT500 PLC ID
38400, 115200
Use PLCAddressView.exe find PLC ID.
PLC Setting:
Communication mode
MT500 Multiple HMI set Slave
138
Device address:
Bit/Word
MT500
MT8000
Range
Ms_RB
RW_Bit
Ms_LB
LB
dddd:0~9999
Ms_RW
RW
ddd:0~65535
Ms_LW
LW
ddd:0~9999
ddd:0~4095
139
Memo
(h): 0~f
Driver Version:
Version
Date
V1.00
Dec/30/2008
Description of Changes
140
Memobus (YASKAWA MP Series controllers)
YASKAWA MP2200, MP2300, MP2300S, MP9xx communication module
http://www.yaskawa.com/
HMI Setting:
Parameters
Recommend
Option
Notes
PLC type
Memobus
Com port
RS485/Ethernet
RS232/RS485 2w/4w, Ethernet
Must match the PLCs port setting.
Baud rate
19200
9600~57600
Must match the PLCs port setting.
Parity bit
Even
Data Bits
Stop Bits
HMI Station No.
PLC Station No.
1-31
TCP Port No.
502
default
Must match the PLCs port setting.
Dose not apply to this protocol.
Must match the PLCs port setting.
Ethernet Module only
PLC Setting:
Communication mode
MEMOBUS, Slave, RTU
Select
Device address:
Bit/Word
B
Device Type
Format
Range
MB_1
ddddh
dddd:0~9999,
Memo
MB 0~9999
h: 0~f
MB_2
ddddh
dddd:10000~65535,
MB 10000~65535
h: 0~f
IB
hhhh
hhhh : 0~A7FF
Read only
IW
hhhh
hhhh : 0~A7FF(8FFF)*
Read only
DW
IL
hhhh
hhhh : 0~A7FE(8FFE)*
Read only
IF
hhhh
hhhh : 0~A7FE(8FFE)*
Read only
MW
ddddd
ddddd:0~65534
Holding Register
Double word
Floating point
DW
ML
ddddd
ddddd:0~65533
MF
ddddd
ddddd:0~65533
*: When connect via Ethernet interface the max range of IW, IL and IF would be restricted.
141
Wiring diagram:
1. RS-232: 217IF-01, 218IF-01
217IF-01 RS232
9P D-SUB Female
MT8000 RS232
COM1
COM2
COM3
TX
TX
TX
RX
RX
RX
RX
TX
GND
GND
GND
7 GND
2. RS-485 2w: 217IF-01
MT8000 RS-485 2w
COM1
217IF-01 RS422/485
14P connector
COM3
RX-
Data-
2, 4
D-
RX+
Data+
1, 3
D+
GND
GND
14
3. RS485 4w: 217IF-01
MT8000 RS-485 2w
217IF-01 RS422/485
COM1
14P connector
RX-
2 TX-
RX+
1 TX+
TX-
4 RX-
TX+
3 RX+
GND
14 GND
4. Ethernet:
MT8000
Wire color
Ethernet Hub or
Ethernet RJ45
1
2
3
4
5
6
7
8
Switch RJ45
TX+
White/Orange
RX+
TX-
Orange
RX-
RX+
White/Green
TX+
BD4+
Blue
BD4+
BD4-
White/Blue
BD4-
RX-
Green
TX-
BD3+
White/Brown
BD3+
BD3-
Brown
BD3-
142
GND
Ethernet: Direct connect (crossover cable)
MT8000
Wire color
Ethernet Module RJ45
TX+
White/Orange
RX+
TX-
Orange
RX-
RX+
White/Green
TX+
BD4+
Blue
BD4+
BD4-
White/Blue
BD4-
RX-
Green
TX-
BD3+
White/Brown
BD3+
BD3-
Brown
BD3-
Ethernet RJ45
1
2
3
4
5
6
7
8
PLC Ethernet Setting:
1. User MPE720 program software, Open Module Configuration. Double click 218IFA.
2. In Transmision Parameters input MP2300S IP address, subnet Mask, Gateway IP.
In Connection Parameter, CNO -1 input: Local Port=502, Node IP address=000.000.000.000,
Node Port=00000, Connect Type=TCP, Protocol Type=MEMOBUS, Code=RTU.
143
3. Close all dialogs and save to MP2300S.
Note:
1. Only CNO 01 able to auto communication with one HMI. other CNO need create ladder
program to communication.
Driver Version:
Version
Date
V1.40
Apr/21/2009
Description of Changes
144
Memory Map protocol
Memory Map protocol is similar to IBM 3764R communication protocol. The MT8000 reserves
512 words of Data memory for use with this protocol. The MT8000 must update the values in
these words. The MT8000 uses the words to display data and control parts status on its screen.
When touch actions are taken, data is sent to the other once, and then update the memory in it. The
MT8000 is always responsible for updating the Data memory.
HMI Setting:
Parameters
Recommend
Option
Notes
PLC type
Memory Map
Com port
RS232
RS232, RS485 4W, 2W
Baud rate
115200
9600~115200
Parity bit
Even
Even, Odd, None
Data Bits
Stop Bits
RS232 default
Device address:
Bit/Word
B
W
Device Type
MB
MW
Format
ddd(h)
ddd
Range
ddd:0~9999 (h): 0~F
ddd:0~9999
The MB and MW are using same area to store data.
MW 0 = MB 000000 ~ MB 0000F
MW 1 = MB 000100 ~ MB 0001F
Wiring diagram:
RS-232:
MT8000 RS232
9P D-SUB
MT8000 RS232
9P D-SUB
2 RX
3 TX
5 GND
3 TX
2 RX
5 GND
RS-485 2W:
MT8000 RS485
9P D-SUB
MT8000 RS485
9P D-SUB
1 RX2 RX+
5 GND
1 RX2 RX+
5 GND
145
Memo
RS-485 4W:
MT8000 RS485
9P D-SUB
1
2
3
4
5
MT8000 RS485
9P D-SUB
RX-
3 TX-
RX+
4 TX+
TX-
1 RX-
TX+
2 RX+
GND
5 GND
NOTE :
For Memory map information, please refer user manual [chapter 31 Memory Map
communication].
Driver Version:
Version
Date
V1.00
Mar/19/2009
Description of Changes
146
MITSUBISHI A1S
MITSUBISHI A1S
http://www.mitsubishi-automation.com/
HMI Setting:
Parameters
Recommend
PLC type
MITSUBISHI A1S
Com port
RS232
Baud rate
9600
Parity bit
Odd
Data Bits
Stop Bits
HMI Station No.
PLC Station No.
Option
Notes
PLC Setting:
Communication
mode
9600, Odd, 8, 1
Device address:
Bit/Word
Device
Type
Format
hhhh
0-ffff
Input Relay
hhhh
0-ffff
Output Relay
ddddd
0-65535
Auxiliary Relay
hhhh
0-ffff
ddddd
0-65535
TV
ddddd
0-65535
Timer Memory
CV
ddddd
0-65535
Counter Memory
ddddd
0-65535
Data Register
hhhh
0-ffff
ddddd
0-65535
Range
d: Decimal h: Hexadecimal
147
Memo
Wiring diagram:
Use the RS422 to RS232 PLC programming cable (show as follows)
MITSUBISHI AnS CPU
Mitsubishi
PLC
MT8000
programming
RS-422
COM1 RS232
Cable
9P D-SUB Female
DB25 Male
2
RX+
RD
TD
TX+
TD
RD
DSR+
GND
GND
GND
RTS
CTS
15
RX-
CTS
RTS
16
TX-
17
DSR148
Driver Version:
Version
Date
V1.00
Sep/18/2009
Description of Changes
149
MITSUBISHI A2A
MITSUBISHI A2A
http://www.mitsubishi-automation.com/
HMI Setting:
Parameters
Recommend
PLC type
MITSUBISHI A2A
Com port
RS232
Baud rate
9600
Parity bit
Odd
Data Bits
Stop Bits
HMI Station No.
PLC Station No.
Option
Notes
PLC Setting:
Communication
mode
9600, Odd, 8, 1
Device address:
Bit/Word
Device
Type
Format
hhhh
0-270f
Input Relay
hhhh
0-270f
Output Relay
dddd
0-9999
Auxiliary Relay
hhhh
0-ffff
ddddd
0-65535
TV
ddd
0-255
Timer Memory
CV
ddd
0-255
Counter Memory
dddd
0-9999
Data Register
hhhh
0-ffff
ddddd
0-65535
Range
d: Decimal h: Hexadecimal
150
Memo
Wiring diagram:
Use the RS422 to RS232 PLC programming cable (show as follows)
MITSUBISHI AnS CPU
Mitsubishi
PLC
MT8000
programming
RS-422
COM1 RS232
Cable
9P D-SUB Female
DB25 Male
2
RX+
RD
TD
TX+
TD
RD
DSR+
GND
GND
GND
RTS
CTS
15
RX-
CTS
RTS
16
TX-
17
DSR-
151
Driver Version:
Version
Date
V1.00
Aug/12/2009
Description of Changes
152
MITSUBISHI A2US
MITSUBISHI A2US
http://www.mitsubishi-automation.com/
HMI Setting:
Parameters
Recommend
Option
PLC type
MITSUBISHI A2US
Com port
RS232
Baud rate
9600
Parity bit
Odd
Data Bits
Stop Bits
HMI Station No.
PLC Station No.
Notes
PLC Setting:
Communication
mode
9600, Odd, 8, 1
Device address:
Bit/Word
Device
Type
Format
hhhh
0-270f
Input Relay
hhhh
0-270f
Output Relay
dddd
0-9999
Auxiliary Relay
TV
ddd
0-255
Timer Memory
CV
ddd
0-255
Counter Memory
dddd
0~9999
Data Register
Range
Memo
d: Decimal h: Hexadecimal
Wiring diagram:
Use the RS422 to RS232 PLC programming cable (show as follows)
153
MITSUBISHI AnS CPU
PLC
Mitsubishi
MT8000
programming
RS-422
COM1 RS232
Cable
9P D-SUB Female
DB25 Male
2
RX+
RD
TD
TX+
TD
RD
DSR+
GND
GND
GND
RTS
CTS
15
RX-
CTS
RTS
16
TX-
17
DSR-
Driver Version:
Version
Date
V1.00
Mar/20/2009
Description of Changes
154
MITSUBISHI A3N/A1SH
MITSUBISHI A3N/A3A/A1SH/A2SH
http://www.mitsubishi-automation.com/
HMI Setting:
Parameters
Recommend
Option
PLC type
MITSUBISHI A3N/A1SH
Com port
RS232
Baud rate
9600
Parity bit
Odd
Data Bits
Stop Bits
HMI Station No.
PLC Station No.
Notes
PLC Setting:
Communication
mode
9600, Odd, 8, 1
Device address:
Bit/Word
Device
Type
Format
hhhh
0-ffff
Input Relay
hhhh
0-ffff
Output Relay
ddddd
0-65535
Auxiliary Relay
hhhh
0-ffff
ddddd
0-65535
TV
ddddd
0-65535
Timer Memory
CV
ddddd
0-65535
Counter Memory
ddddd
0-65535
Data Register
hhhh
0-ffff
ddddd
0-65535
Range
d: Decimal h: Hexadecimal
155
Memo
Wiring diagram:
Use the RS422 to RS232 PLC programming cable (show as follows)
MITSUBISHI AnS CPU
Mitsubishi
PLC
MT8000
programming
RS-422
COM1 RS232
Cable
9P D-SUB Female
DB25 Male
2
RX+
RD
TD
TX+
TD
RD
DSR+
GND
GND
GND
RTS
CTS
15
RX-
CTS
RTS
16
TX-
17
DSR-
Driver Version:
156
Version
Date
V1.00
Oct/20/2009
Description of Changes
Note: This driver is not available for On-Line Simulation.
157
MITSUBISHI AJ71
Mitsubishi A series PLC with AJ71C24 communication module using the Computer Link protocol.
http://www.mitsubishi-automation.com
HMI Setting:
Parameters
Recommend
Option
Notes
PLC type
MITSUBISHI AJ71
MITSUBISHI AJ71(AnA/AnU CPU)
MITSUBISHI AJ71
Com port
RS485 4W
RS485 4W, RS232
Baud rate
19200
9600, 19200
Parity bit
Even
Even, Odd, None
Data Bits
Stop Bits
HMI Station No.
PLC Station No.
PLC Setting:
Communication mode
Computer Link protocol 9600, Even, 8, 1 (default)
Mode Setting Switch
Format 1
Parity Check
Enable
Sum Check
Enable
Device address:
Bit/Word
B
Device Type
Format
Range
hhh
hhh: 0~270F
Memo
Input Bits
(hex-decimal)
Y
hhh
hhh: 0~270F
Output Bits
(hex-decimal)
dddd
dddd:0~9999
TV
ddd
ddd:0~255
Timer Preset Value
CV
ddd
ddd:0~255
Counter Preset Value
dddd
ddd:0~9999
Data Registers
158
Internal Relays
Wiring diagram:
RS-485 4W:
AJ71C24
MT800 Com1 RS-485]
RS-422
9P D-SUB
1
RX-
SDB
RX+
SDA
TX-
RDB
TX+
RDA
GND
GND
RS-232: A1SJ71UC24-R2
RS232 port
9P D-SUB Female
MT8000 RS232
9P D-SUB
COM1
COM2
COM3
TX
TX
TX
RXD
RX
RX
RX
TXD
GND
GND
DCD
DTR
DSR
RTS
CTS
GND
GND
Driver Version:
Version
Date
V1.40
Feb/09/2009
Description of Changes
159
MITSUBISHI MELSEC-Q (Ethernet)
MITSUBISHI Q series, MELSEC-Q protocol application to CPU of Ethernet interface or Ethernet
module QJ71E71.
http://www.mitsubishi-automation.com
HMI Setting:
Parameters
Recommend
PLC type
MITSUBISHI MELSEC-Q
Com port
Ethernet
PLC Station No.
Parameter1
Option
Notes
It must same as the PLC setting
0~255
Q13UDEH has to set 255
Networking no. (it must the same
0~255
Q13UDEH has to set 0
as PLC setting)
TCP/IP port
Advice to set port no. to 4999
It must same as the PLC setting
Device address:
Bit/Word
Device Type
Format
Range
SM
dddd
0 ~ 2047
Special Relay
hhhh
0 ~ 1FFF
Input Relay
hhhh
0 ~ 1FFF
Output Relay
dddd
0 ~ 8191
Internal Relay
dddd
0 ~ 8191
Latch Relay
dddd
0 ~ 2047
Annunciator
dddd
0 ~ 2047
Edge Relay
hhhh
0 ~ 1FFF
Link Relay
TS
dddd
0 ~ 2047
Timer Contact
TC
dddd
0 ~ 2047
Timer Coil
SS
dddd
0 ~ 2047
Retentive Timer Contact
SC
dddd
0 ~ 2047
Retentive Timer Coil
CS
dddd
0 ~ 1023
Counter Contact
CC
dddd
0 ~ 1023
Counter Coil
SB
hhh
0 ~ 7FF
Special Link Relay
dddd
0 ~ 8191
Step relay
DX
hhhh
0 ~ 1FFF
Direct Input
DY
hhhh
0 ~ 1FFF
Direct Output
SD
dddd
0 ~ 2047
Special register
160
Memo
ddddd
0 ~ 12287
Data Register
hhhh
0 ~ 1FFF
Link Register
TN
dddd
0 ~ 2047
Timer Current value
SN
dddd
0 ~ 2047
Retentive Timer Current value
CN
dddd
0 ~ 1023
Counter Current value
SW
hhh
0 ~ 7FF
Special Link Register
dd
0 ~ 15
Index Register
ddddd
0 ~ 32767
File Register
ZR
hhhhh
0 ~ FE7FF
File Register
Note: ddd: Decimal, hhh: Hexadecimal, ooo: Octal.
Every mdel of CPU is different, we suggest user to refer to MITSUBISHI MELSEC-Q manuals
Device List.
Wiring diagram:
Ethernet:
MT8000 Ethernet Wire color
Ethernet Hub or
RJ45
Switch RJ45
1
2
3
4
5
6
7
8
TX+
TXRX+
BD4+
BD4RXBD3+
BD3-
White/Orange
Orange
White/Green
Blue
White/Blue
Green
White/Brown
Brown
1
2
3
4
5
6
7
8
RX+
RXTX+
BD4+
BD4TXBD3+
BD3-
Ethernet: Direct connect (crossover cable)
MT8000 Ethernet Wire color
Modbus TCP Device
RJ45
RJ45
1
2
3
TX+
TXRX+
White/Orange
Orange
White/Green
3
6
1
RX+
RXTX+
4
5
6
7
8
BD4+
BD4RXBD3+
BD3-
Blue
White/Blue
Green
White/Brown
Brown
4
5
2
7
8
BD4+
BD4TXBD3+
BD3-
161
MITSUBISHI Q series Ethernet module setting:
Remark: If using QJ71E71 module, please refer MITSUBISHI QJ71E71 connection guide.
1. Click PLC parameter
2. Built-in Ethernet port.
3. Click Open settings and then set the IP address and communication data code
4. Set the MC protocol-TCP Port No.1387 (Hex) and in EB8000 TCP port is 4999 (Dec).
Note: In EB8000, please fill in network no. in Parameter 1 as PLC setting.
For example,
From below picture, the Network no. is 2
162
Users have to set 2 in Parameter 1 in EB8000.
163
Driver Version:
Version
Date
1.00
Jun/16/2009
Description of Changes
Add address type [S], [SM], [D_bit]
164
MITSUBISHI FX0n/FX2
Mitsubishi FX0s/FX0n/FX1s/FX2 PLC
http://www.mitsubishi-automation.com
HMI Setting:
Parameters
Recommend
Option
Notes
PLC type
Mitsubishi FX0n/FX2
Mitsubishi FX0n/FX2
Com port
RS485
RS232/RS485
Baud rate
9600
9600/19200/38400/57600/
must same as the PLC setting
115200
Parity bit
Even
Even, Odd, None
must same as the PLC setting
Data Bits
7,8
must same as the PLC setting
Stop Bits
1,2
must same as the PLC setting
HMI Station No.
0-255
Does not apply to this protocol
PLC Station No.
0-255
must same as the PLC setting
PLC Setting:
Communication mode
9600,Even,7,1
Device address:
Bit/Word
Device
Type
Format
Range
Memo
ooo
0-377
Input Relay
ooo
0-377
Output Relay
ddd
0-9999
Auxiliary Relay
ddd
0-255
Timer Relay
ddd
0-255
Counter Relay
D_Bit
dddd(dd)
0-9999(0~15)
dddd
0-4095
SM
dddd
8000-9999
TV
ddd
0-255
Timer Memory
CV
ddd
0-199
Counter Memory
ddd
0-9999
Data Register
DW
CV2
ddd
200-255
Counter Memory(D Word)
165
Data Register Bit (D)
States
Special Aux. Relays
SD
ddd
8000-9999
Special Data Register
Wiring diagram:
MT8000
Mitsubishi PLC CPU
COM1 [RS-485] 4w
RS422 Port
9P D-SUB
8P MiniDin Female
RX-
TX-
RX+
TX+
GND
GND
TX-
RX-
TX+
RX+
Driver Version:
Version
Date
1.10
August 27.2009
Description of Changes
Add address type [S], [SM], [D_bit]
166
8Pin miniDin
Female
MITSUBISHI FX2n
Mitsubishi FX1n/FX2n series PLC
http://www.mitsubishi-automation.com
HMI Setting:
Parameters
Recommend
Option
Notes
PLC type
Mitsubishi FX2n
Mitsubishi FX2n
Com port
RS485
RS232/RS485
Baud rate
9600
9600/19200/38400/5760
0/115200
Parity bit
Even
Data Bits
Stop Bits
HMI Station No.
PLC Station No.
Online Simulator
YES
Broadcast command
NO
Extend address mode
NO
PLC Setting:
Communication mode
9600,Even,7,1
Device address:
Bit/Word
Device
Type
Format
Range
Memo
ooo
0-377
Input Relay
ooo
0-377
Output Relay
dddd
0-7999
Auxiliary Relay
ddd
0-255
Timer Relay
ddd
0-255
Counter Relay
SM
dddd
8000-9999
D_Bit
dddd(dd)
0~7999(0~15)
dddd
0~4095
State Relay (S)
TV
ddd
0-255
Timer Memory
167
Special Auxiliary Relay
Data Register Bit (D)
Bit/Word
Device
Type
Format
Range
Memo
CV
ddd
0-199
Counter Memory
ddd
0-7999
Data Register
DW
CV2
ddd
200-255
Counter Memory(D Word)
SD
ddd
8000-9999
Special Data Register
Wiring diagram:
MT8000
Mitsubishi FX series PLC
COM1 [RS-485]4w
9P D-SUB
CPU RS422 Port
8P MiniDin Female
1
2
3
4
5
4
7
1
2
3
RXRX+
TXTX+
GND
TXTX+
RXRX+
GND
Driver Version:
Version
Date
V1.60
Sep/10/2009
Description of Changes
168
8Pin miniDin
Female
MITSUBISHI FX232/485BD
Mitsubishi FX0n/FX2/FX2n COM For Communication Module BD
FX2N-485-BD, FX2N-232-BD, FX1N-485-BD and FX1N-232-BD
http://www.mitsubishi-automation.com
HMI Setting:
Parameters
Recommend
PLC type
MITSUBISHI
Option
Notes
in accordance with the BD module
FX232/485BD
Com port
RS232/RS485
RS232/RS485 2w/4w
Baud rate
19200
9600/19200
must same as the PLC setting
Parity bit
Even
Even, Odd, None
must same as the PLC setting
Data Bits
7,8
must same as the PLC setting
Stop Bits
1,2
must same as the PLC setting
HMI Station No.
PLC Station No.
Does not apply to this protocol
0-15
must same as the PLC setting
Note: we suggest the turn around delay to set 8. (For i series)
Online Simulator
YES
Extend address mode
YES
Broadcast command
PLC Setting:
Communication mode
Must set PLC station when use the BD Module
Register D8120 setting: set b9 and b8 of BFM#0 as 0
FX2N-485-BD, FX1N-485-BD
FX2N-232-BD, FX1N-232-BD
169
Device address:
Bit/Word
Device
Type
Format
Range
Memo
ooo
0-377
Input Relay
ooo
0-377
Output Relay
ddd
0-9999
Auxiliary Relay
ddd
0-255
Timer Relay
ddd
0-255
Counter Relay
TV
ddd
0-255
Timer Memory
CV
ddd
0-199
Counter Memory
ddd
0-9999
Data Register
CV2
ddd
200-255
Counter Memory(D Word)
Wiring diagram:
Communication Module RS232BD:
MT8000 RS232
9P D-SUB
COM1
COM2
232BD Module
9P D-SUB Female
COM3
3 TX
4 TX
7 TX
2 RX
6 RX
8 RX
5 GND 5 GND 5 GND
2 RXD
3 TXD
5 GND
Communication Module RS485BD:
MT8000 COM1
485BD Module
RS-485 4w
5P terminal
9P D-SUB Male
1
RX-
SDB
RX+
SDA
TX-
RDB
TX+
RDA
GND
SG
170
Communication Module RS485BD:
MT8000 RS-485 2Wire
RS485BD Module
9P D-SUB
5P terminal
COM1
COM3
RX-
Data-
SDB
RX+
Data+
SDA
TX-
RDB
TX+
RDA
GND
GND
SG
Driver Version:
Version
Date
V1.00
Dec/30/2008
Description of Changes
171
MITSUBISHI FX3U/FX3G
Mitsubishi FX3U/FX3UC/FX3G
http://www.mitsubishi-automation.com
HMI Setting:
Parameters
Recommend
PLC type
MITSUBISHI FX3u
Com port
RS485 4w
RS232/RS485 2w/4w
Baud rate
9600
9600/19200
Parity bit
Even
must same as the PLC setting
Data Bits
must same as the PLC setting
Stop Bits
must same as the PLC setting
HMI Station No.
Does not apply to this protocol
PLC Station No.
Does not apply to this protocol
Online Simulator
YES
Option
Notes
must same as the PLC setting
Extend address mode
NO
PLC Setting:
Communication mode
9600,Even,7,1
Device address:
Bit/Word
Device
Type
Format
Range
Memo
ooo
0~377
Input Relay
ooo
0~377
Output Relay
dddd
0~7679
Auxiliary Relay
SM
dddd
8000~9999
dddd
0~4095
State Relay (S)
ddd
0~511
Timer Relay (T)
ddd
0~199
Counter Relay (C)
D_Bit
dddd(dd)
dddd=0~7999 (dd)=0~15
172
Special Relay (M)
Data Register Bit (D)
Bit/Word
Device
Type
Format
Range
Memo
TV
ddd
0~511
Timer Memory (T)
CV
ddd
0~199
Counter Memory (C)
DW
CV2
ddd
200~255
Counter Memory(D Word)
dddd
0~7999
Data Register (D)
SD
dddd
8000~9999
ddddd
0~32767
Special Data Register (D)
Extended Register (R)
Wiring diagram:
MT8000
Mitsubishi FX series PLC
COM1[RS-485]4w
9P D-SUB
CPU RS422 Port
8P MiniDin Female
RX-
TX-
RX+
TX+
TX-
RX-
TX+
RX+
GND
GND
Driver Version:
Version
Date
V1.40
Apr/15/2009
Description of Changes
173
8Pin miniDin
Female
MITSUBISHI FX3U-ETHERNET
MITSUBISHI FX SERIES, Module: FX3U-ENET
http://www.mitsubishi-automation.com
HMI Setting:
Parameters
Recommend
PLC type
MITSUBISHI FX3u
Option
Notes
(Ethernet)
Com port
Ethernet
PLC Station No.
0 (default)
Refer Module Setting
TCP/IP port
5001(default)
Refer Module Setting
Device address:
Bit/Word
Device type
Format
Range
Memo
ooo
0 ~ 377
Input
ooo
0 ~ 377
Output Relay
dddd
0 ~ 7679
Internal Relay
dddd
0 ~ 4095
Step Relays
ddd
0 ~ 511
Timer Contacts
ddd
0 ~ 255
Counter Contacts
SM
dddd
8000 ~ 8511
Special Int. Relays
D_Bit
dddd(dd)
0-799915
Data Register Bit
Access
TV
ddd
0 ~ 511
Timer Value
ddddd
0 ~ 32767
File Register
CV
ddd
0 ~ 199
Counter Value
dddd
0 ~ 7999
Data Registers
CV2
ddd
200 ~255
Counter Value
SD
dddd
8000 ~ 8511
ddd: (Decimal), hhh:(Hexadecimal), ooo:(Octal).
174
Special Data Registers
Wiring diagram:
Ethernet:
MT8000
Ethernet RJ45
Wire color
Ethernet Hub or
Switch RJ45
TX+
White/Orange
RX+
TX-
Orange
RX-
RX+
White/Green
TX+
BD4+
Blue
BD4+
BD4-
White/Blue
BD4-
RX-
Green
TX-
BD3+
White/Brown
BD3+
BD3-
Brown
BD3-
Ethernet: Direct connect (crossover cable)
MT8000
Wire color
Ethernet RJ45
Modbus TCP Device
RJ45
TX+
White/Orange
RX+
TX-
Orange
RX-
RX+
White/Green
TX+
BD4+
Blue
BD4+
BD4-
White/Blue
BD4-
RX-
Green
TX-
BD3+
White/Brown
BD3+
BD3-
Brown
BD3-
175
Fx3u-ENET module setting:
Before using Ethernet module, using GX Developer / FX Configurator-EN to set the Ethernet
module, the FX3u-ENET module settings as below steps.
1. Open GX Developer, select Read from PLC in Online list.
2. Select FXCPU in PLC series.
3. Users have to connect PLC via series port for setting IP address at first time.
176
4. After finishing the PLC settings, select Tools/FX special function utility/FX Configurator-EN
5. Select Module 0 in Ethernet Module settings.
( If more than one module, please setting modules step by step)
177
6. In Ethernet operational settings, select the related parameters and IP address and then
press End to finish the settings.
7. In Ethernet open settings, press End after setting the below parameters.
178
(The first Protocol means using GX Developer to communicate with module, The max. Fixed
buffer communication preocedure is 4 units.)
8. After setting the parameters to PLC, restart for using Ethernet communication.
179
Driver Version:
Version
Date
V1.00
Feb/12/2009
Description of Changes
180
MITSUBISHI Q00J CPU
MITSUBISHI Q00J CPU
HMI Setting:
Parameters
Recommend
Option
Notes
PLC type
MITSUBISHI Q00J
Com port
RS-232
CPU port
Baud rate
115200
9600,19200,38400,57600,115200
Data bit
Parity bit
Odd
Stop bit
PLC Station No.
Device address:
Bit/Word
Device Type
Format
Range
SM
dddd
0~1023
hhh
0 ~ 7FF
hhh
0 ~ 7FF
dddd
0 ~ 8191
dddd
0 ~ 2047
dddd
0 ~ 1023
dddd
0 ~ 1023
hhh
0 ~ 7FF
SB
hhh
0 ~ 3FF
SD
ddd
0~1023
hhh
0 ~ 7FF
dddd
0 ~ 511
SW
hhh
0 ~ 3FF
dddd
0~9
dddd
0 ~ 511
dddd
0 ~ 11135
ddd: Decimal, hhh: Hexadecimal, ooo: Octal.
181
Memo
Wiring diagram:
RS-232:
MT8000 RS232
Q00
9P D-SUB
CPU port
Mini-DIN 6pin
COM1
COM2
COM3
3 TX
4 TX
7 TX
2 RX
6 RX
8 RX
5 GND 5 GND 5 GND
3
4
5
RXD
TXD
GND
MINI-DIN 6Pin
Female
MT8-Mitsubishi-Q-3M cable is able to connect MT8000 and Mitsubishi Q series directly.
ftp://ftp.weintek.com/MT8000/eng/DataSheet/RZC000043_MT8_MITSUBISHI_Q_3M.pdf
Driver Version:
Version
Date
V1.10
Sep/18/2009
Description of Changes
182
MITSUBISHI Q02H
Mitsubishi Q02H CPU port.
http://www.mitsubishi-automation.com
HMI Setting:
Parameters
Recommend
PLC type
MITSUBISHI Q02H
Com port
RS232
RS485 4W, RS232
Baud rate
115200
115200 only
Parity bit
Odd
Data Bits
Stop Bits
HMI Station No.
PLC Station No.
Online Simulator
YES
Broadcast command
NO
Option
Notes
Extend address mode
NO
PLC Setting:
Communication mode
Device address:
Bit/Word
Device Type
Format
Range
hhh
0~1FFF
Input Relay
hhh
0~1FFF
Output Relay
dddd
0~8191
Internal Relay
dddd
0~8191
Latch Relay
dddd
0~2047
Annunciator
dddd
0~2047
Edge Relay
hhh
0~1FFF
Link Relay
TC
ddd
0~2047
Timer Coil
SS
ddd
0~2047
Retentive Timer Contact
SC
ddd
0~2047
Retentive Timer Coil
CS
ddd
0~1023
Counter Contact
183
Memo
Bit/Word
Device Type
Format
Range
Memo
CC
ddd
0~1023
Counter Coil
SB
hhh
0~7FF
Special Link Relay
dddd
0~8191
Step Relay
DX
hhh
0~1FFF
Direct Input
DY
hhh
0~1FFF
Direct Output
TS
ddd
0~2047
Timer Contact
hhh
0~1FFF
Link Register
TN
ddd
0~2047
Timer Current Value
SN
ddd
0~2047
Retentive Timer Current Value
CN
ddd
0~1023
Counter Current Value
ddddd
0~32767
File Register
SW
hhh
0~7FF
0~9
ZR
hhhh
0~FFFF
File Register
ddddd
0~12287
Data Register
Special Link Register
Index Register
ddd: Decimal, hhh: Hexadecimal, ooo: Octal.
Wiring diagram:
RS-232:
MT8000 RS232
9P D-SUB
COM1
COM2
COM3
TX
TX
TX
RXD
RX
RX
RX
TXD
MINI-DIN 6Pin
GND
GND
GND
GND
Female
CTS
RTS
Q02
CPU port
Mini-DIN 6pin
Driver Version:
Version
Date
V1.40
Aug/19/2009
V1.50
Jan/05/2010
Description of Changes
Fixed communication problem
184
MITSUBISHI Q01U Q02U
MITSUBISHI Q01U, Q02U, Q00UJ CPU
HMI Setting:
Parameters
Recommend
Option
PLC type
MITSUBISHI Q02U
Com port
RS232
RS485 4W, RS232
Baud rate
115200
115200 only
Notes
CPU port connect directly
9600,19200,38400,57600,115200
For Q00UJ, only 9600 available
Parity bit
Odd
Data Bits
Stop Bits
PLC Station No.
No
Device address:
Bit/Word
Device Type
Format
Range
Memo
hhhh
0~1FFF
Input Relay
hhhh
0~1FFF
Output Relay
dddd
0~8191
Internal Relay
dddd
0~8191
Latch Relay
dddd
0~2047
Annunciator
dddd
0~2047
Edge Relay
hhhh
0~1FFF
Link Relay
SB
hhh
0~7FF
Special Link Relay
hhhh
0~1FFF
Link Register
dddd
0~0247
Timer Current Value
SW
hhh
0~7FF
Special Link Register
dd
0~19
dddd
0~1023
Counter Current Value
ddddd
0~12287
Data Register
Index Register
ddd: Decimal, hhh: Hexadecimal, ooo: Octal.
Note:
EB8000 doesnt support MITSUBISHI Q02U CPU to do on-line simulation on PC.
When using Q02U driver, HMI needs 10 seconds to initial the PLC Q02U driver. Before finishing
initial, we suggest users dont wrire data to PLC, or it could cause the PLC no response and if
185
the wiring diagram or the data are incorrect, it could cause PLC locked. If the PLC locked, users
have to restart PLC or reinstall PLC module.
Wiring diagram:
RS-232:
MT8000 RS232
9P D-SUB
COM1
COM2
COM3
TX
TX
TX
RXD
RX
RX
RX
TXD
MINI-DIN 6Pin
GND
GND
GND
GND
Female
CTS
RTS
Q02
CPU port
Mini-DIN 6pin
Driver Version:
Version
Date
V1.40
Jul/08/2009
Description of Changes
186
MITSUBISHI Q00UJ Q01U Q02U USB
MITSUBISHI Q00UJ, Q01U, Q02U USB Port
HMI Setting:
Parameters
Recommend
Option
PLC type
MITSUBISHI Q02U
Com port
RS232
RS485 4W, RS232
Baud rate
115200
115200 only
Parity bit
Odd
Data Bits
Stop Bits
PLC Station No.
No
Notes
CPU port connect directly
9600,19200,38400,57600,115200
Device address:
Bit/Word
Device Type
Format
Range
Memo
hhhh
0~1FFF
Input Relay
hhhh
0~1FFF
Output Relay
dddd
0~8191
Internal Relay
dddd
0~8191
Latch Relay
dddd
0~2047
Annunciator
dddd
0~2047
Edge Relay
hhhh
0~1FFF
Link Relay
SB
hhh
0~7FF
Special Link Relay
hhhh
0~1FFF
Link Register
dddd
0~0247
Timer Current Value
SW
hhh
0~7FF
Special Link Register
dd
0~19
dddd
0~1023
Counter Current Value
ddddd
0~12287
Data Register
Index Register
ddd: Decimal, hhh: Hexadecimal, ooo: Octal.
Note:
EB8000 doesnt support MITSUBISHI Q02U CPU to do on-line simulation on PC.
When using Q02U driver, HMI needs 10 seconds to initial the PLC Q02U driver. Before finishing
initial, we suggest users dont wrire data to PLC, or it could cause the PLC no response and if
the wiring diagram or the data are incorrect, it could cause PLC locked. If the PLC locked, users
187
have to restart PLC or reinstall PLC module.
Driver Version:
Version
Date
V1.00
Feb/09/2010
Description of Changes
188
MITSUBISHI Q06H
Mitsubishi Q06H CPU port.
http://www.mitsubishi-automation.com
HMI Setting:
Parameters
Recommend
PLC type
MITSUBISHI Q06H
Com port
RS232
RS485 4W, RS232
Baud rate
115200
115200 only
Parity bit
Odd
Data Bits
Stop Bits
HMI Station No.
PLC Station No.
Online Simulator
YES
Broadcast command
NO
Option
Notes
Extend address mode
NO
PLC Setting:
Communication mode
Device address:
Bit/Word
Device Type
Format
Range
hhh
0~1FFF
Input Relay
hhh
0~1FFF
Output Relay
dddd
0~8191
Internal Relay
dddd
0~8191
Latch Relay
dddd
0~2047
Annunciator
dddd
0~2047
Edge Relay
hhh
0~1FFF
Link Relay
TC
ddd
0~2047
Timer Coil
SS
ddd
0~2047
Retentive Timer Contact
SC
ddd
0~2047
Retentive Timer Coil
189
Memo
Bit/Word
Device Type
Format
Range
Memo
CS
ddd
0~1023
Counter Contact
CC
ddd
0~1023
Counter Coil
SB
hhh
0~7FF
Special Link Relay
dddd
0~8191
Step Relay
DX
hhh
0~1FFF
Direct Input
DY
hhh
0~1FFF
Direct Output
TS
ddd
0~2047
Timer Contact
hhh
0~1FFF
Link Register
TN
ddd
0~2047
Timer Current Value
SN
ddd
0~2047
Retentive Timer Current Value
CN
ddd
0~1023
Counter Current Value
ddddd
0~32767
File Register
SW
hhh
0~7FF
0~9
ZR
hhhh
0~FFFF
File Register
ddddd
0~12287
Data Register
Special Link Register
Index Register
ddd: Decimal, hhh: Hexadecimal, ooo: Octal.
Wiring diagram:
RS-232:
MT8000 RS232
9P D-SUB
COM1
COM2
COM3
TX
TX
TX
RXD
RX
RX
RX
TXD
MINI-DIN 6Pin
GND
GND
GND
GND
Female
CTS
RTS
Q02
CPU port
Mini-DIN 6pin
Driver Version:
Version
Date
V1.40
Jun/03/2009
Description of Changes
190
MITSUBISHI Q00/Q00UJ/Q01/QJ71
Mitsubishi Q series PLC with QJ71C24 communication module, Q00, Q00UJ, Q01 CPU port.
http://www.mitsubishi-automation.com
HMI Setting:
Parameters
Recommend
PLC type
MITSUBISHI
Option
Notes
Melsec_QJ71
Com port
RS232
RS485 4W, RS232
Baud rate
9600
9600~115200
Parity bit
Odd
Data Bits
Stop Bits
HMI Station No.
PLC Station No.
Online Simulator
YES
Extend address mode
NO
PLC Setting:
Communication mode
Q00, Q01 CPU port setting:
1. In the GX Developer PLC data list click the PLC
parameter
2. In the PLC parameter select Serial page.
3. Select Use serial communication
4. Set the Transmission speed. 9600~115200.
5. Select Sum check
6. Select Transmission wait time to 10ms.
7. Select RUN write setting
8. Click End close the dialog.
9. Write the PLC Parameter to PLC.
10. RESET the PLC, the parameter will active.
Note: Please check Permit in RUN write setting item.
191
Device address:
Bit/Word
Device Type
Format
Range
hhh
0~1FFF
Input Relay
hhh
0~1FFF
Output Relay
dddd
0~8191
Internal Relay
dddd
0~8191
Latch Relay
dddd
0~2047
Annunciator
dddd
0~2047
Edge Relay
hhh
0~1FFF
Link Relay
TC
ddd
0~2047
Timer Coil
SS
ddd
0~2047
Retentive Timer Contact
SC
ddd
0~2047
Retentive Timer Coil
CS
ddd
0~1023
Counter Contact
CC
ddd
0~1023
Counter Coil
SB
hhh
0~7FF
Special Link Relay
dddd
0~8191
Step Relay
DX
hhh
0~1FFF
Direct Input
DY
hhh
0~1FFF
Direct Output
TS
ddd
0~2047
Timer Contact
hhh
0~1FFF
Link Register
TN
ddd
0~2047
Timer Current Value
SN
ddd
0~2047
Retentive Timer Current Value
CN
ddd
0~1023
Counter Current Value
192
Memo
Bit/Word
Device Type
Format
Range
Memo
ddddd
0~32767
SW
hhh
0~7FF
0~9
ZR
hhhh
0~FFFF
File Register
ddddd
0~12287
Data Register
File Register
Special Link Register
Index Register
ddd: Decimal, hhh: Hexadecimal, ooo: Octal.
Wiring diagram:
RS-485 4W:
MT8000 COM1
QJ71C24 CH.2
RS-485 4w
RS-422
9P D-SUB Male
1
RX-
SDB
RX+
SDA
TX-
RDB
TX+
RDA
GND
GND
RS-232:
QJ71C24 CH.1
RS232 port
9P D-SUB Male
MT8000 RS232
9P D-SUB
COM1
COM2
COM3
TX
TX
TX
RXD
RX
RX
RX
TXD
GND
GND
DCD
DTR
DSR
RTS
CTS
GND
GND
Q00, Q01 CPU port RS-232:
193
Q00, Q01
CPU port
Mini-DIN 6pin
MT8000 RS232
9P D-SUB
COM1
COM2
COM3
TX
TX
TX
RXD
RX
RX
RX
TXD
MINI-DIN 6Pin
GND
GND
Female
GND
GND
Q00UJ CPU port RS-232:
MT8000 RS232
9P D-SUB
COM1
COM2
COM3
TX
TX
TX
RXD
RX
RX
RX
TXD
MINI-DIN 6Pin
GND
GND
GND
GND
Female
CTS
RTS
Q00UJ
CPU port
Mini-DIN 6pin
Driver Version:
Version
Date
V1.20
Dec/30/2008
Description of Changes
194
MITSUBISHI QJ71E71
Mitsubishi Q type, QJ71E71-100 Ethernet module.
http://www.mitsubishi-automation.com
HMI Setting:
Parameters
Recommend
PLC type
MITSUBISHI QJ71E71
Option
Notes
[V1.00]
Com port
Ethernet
PLC Station No.
TCP/IP port
5002
1~99
Note: MITSUBISHI QJ71E71 only supports PLC Network no. 1.
If PLCs Network no. is not 1, please use MISTSUBISHI MELSEC-Q(Ethernet) driver and fill
in the Network no. in Parameter 1. Please refer MISTSUBISHI MELSEC-Q(Ethernet) for further
information.
Device address:
Bit/Word
Device Type
Format
Range
hhhh
0~1FFF
Input Relay
hhhh
0~1FFF
Output Relay
dddd
0~8191
Internal Relay
dddd
0~8191
Latch Relay
dddd
0~2047
Annunciator
dddd
0~2047
Edge Relay
hhhh
0~1FFF
Link Relay
SB
hhhh
0~2047
Special Link Relay
DX
hhhh
0~1FFF
Direct Input
DY
hhhh
0~1FFF
Direct Output
hhhh
0~2FFF
Link Register
dddd
0~32767
File Register
SW
hhh
0~7FF
dd
0~15
ZR
hhhh
0~FFFF
File Register
ddddd
0~12287
Data Register
Ddd: Decimal, hhh: Hexadecimal
195
Memo
Special Link Register
Index Register
Wiring diagram:
Ethernet:
MT8000 Ethernet Wire color
Ethernet Hub or
RJ45
Switch RJ45
1
2
3
TX+
TXRX+
White/Orange
Orange
White/Green
1
2
3
RX+
RXTX+
4
5
6
7
8
BD4+
BD4RXBD3+
BD3-
Blue
White/Blue
Green
White/Brown
Brown
4
5
6
7
8
BD4+
BD4TXBD3+
BD3-
Ethernet: Direct connect (crossover cable)
MT8000 Ethernet Wire color
Modbus TCP Device
RJ45
RJ45
1
2
3
4
5
6
7
8
TX+
TXRX+
BD4+
BD4RXBD3+
BD3-
White/Orange
Orange
White/Green
Blue
White/Blue
Green
White/Brown
Brown
3
6
1
4
5
2
7
8
QJ71E71-100 Ethernet module settings:
196
RX+
RXTX+
BD4+
BD4TXBD3+
BD3-
1.
Use Q-CPUs USB or RS232 setting PLC parameters.
2.
Click Operational setting to set IP information.
197
3.
Select Ethernet (2.0) for communicating with HMI.
4.
Click Open settings to set the system.
198
5.
Press END to finish settings.
199
6.
Restart PLC software and select [READ FROM PLC], click QCPU(Qmode) and
press OK.
7.
Select Ethernet board in PC Side I/F to set Network and Station no..(the Station
no.1 is PCs station no. not Ethernet modules, range from 2~64, the Network no.
can not the same as PCs number)
8.
Select Ethernet module in PLC Side I/F to set QJ71E71s IP address.(IP address
= Network Parameters IP address)
9.
In Other station, click Other station(Single network) setting Check at
communication time and Retry times.
200
After finishing settings as above, click Connection test for testing the
communication and sending the PLCs program.
Driver Version:
Version
Date
V2.10
Feb/05/2009
Description of Changes
201
MODBUS ASCII
MODBUS ASCII CONTROLLER
http://www.modbus.org
HMI Setting:
Parameters
Recommend
Option
PLC type
Modbus ASCII
Com port
RS485
RS232/RS485
Baud rate
9600
9600/19200/38400/57600/
Notes
115200
Parity bit
Even
Even, Odd, None
Data Bits
7,8
Stop Bits
1,2
HMI Station No.
PLC Station No.
Does not apply to this protocol
0-255
Online Simulator
YES
Extend address mode
YES
Broadcast command
YES
PLC Setting:
Communication mode
Modbus ASCII protocol
Device address:
Bit/Word
Device Type
Format
Range
Memo
0x
ddddd
1-65535
Output bit
1x
ddddd
1-65535
Input bit (read only)
3x_Bit
ddddd(dd)
100-6553515
Input Register bit (read only)
4x_Bit
ddddd(dd)
100-6553515
Output Register bit
3x
ddddd
1-65535
Input Register (read only)
4x
ddddd
1-65535
Output Register
202
Modbus RTU function code:
0x
1x
0x01 Read coil
0x02 Read discrete input
0x05 write single coil
N/A for write operation
3x
0x04 Read input register
4x
0x03 Read holding register
3xbit is equivalent to 3x
N/A for write operation
0x10 write multiple register
4xbit is equivalent to 4x
Wiring diagram:
MODBUS RS232 PORT
MT8000 RS-232
Modbus ASCII
9P D-SUB
Controller RS232
COM1
COM2
COM3
Port
TX
TX
TX
RXD
RX
RX
RX
TXD
GND
GND
GND
GND
RTS
CTS
MODBUS RS422/485 PORT
MT8000
Modbus ASCII Controller
COM1 RS-485 4w
RS422 Port
RX-
TX-
RX+
TX+
TX-
RX-
TX+
RX+
GND
GND
MT8000 RS-485 2Wire
Modbus ASCII
9P D-SUB
Controller RS485
COM1
COM3
RX-
Data-
D-
RX+
Data+
D+
GND
GND
GND
203
Driver Version:
Version
Date
V1.40
Apr/17/2009
Description of Changes
204
MODBUS RTU
MODBUS RTU CONTROLLER
http://www.modbus.org
HMI Setting:
Parameters
Recommend
Option
PLC type
Modbus RTU
Com port
RS485
RS232/RS485
Baud rate
9600
9600~115200
Parity bit
Even
Even, Odd, None
Data Bits
7,8
Stop Bits
1,2
HMI Station No.
PLC Station No.
Notes
Does not apply to this protocol
0-255
Online Simulator
YES
Extend address mode
YES
Broadcast command
YES
PLC Setting:
Communication mode
Modbus RTU protocol
Device address:
Bit/Word
Device Type
Format
Range
0x
ddddd
1-65535
Output bit
0x_multi_coils
ddddd
1-65535
Write Multiple Coils
1x
ddddd
1-65535
Input bit (read only)
3x_Bit
ddddd(dd)
100-6553515
Input Register bit (read only)
4x_Bit
ddddd(dd)
100-6553515
Output Register bit
6x_Bit
ddddd(dd)
100-6553515
Output Register bit
3x
ddddd
1-65535
Input Register (read only)
4x
ddddd
1-65535
Output Register
DW
5x
ddddd
1-65535
4x double word swap
6x
ddddd
1-65535
4x single word write
4x_32Bit
ddddd
1-65535
4x High/low byte swap
205
Memo
NOTE:
Address type 5x are mapping to Hold Reg. The communication protocol of 5x is almost same as
4x except 5xmaking double word swap.
If 4x has following information
Address
Data in word
0x1
0x2
0x3
0x4
0x5
0x6
Data
0x20001
0x40003
0x60005
Address
Data in word
0x2
0x1
0x4
0x3
0x6
0x5
...
For 5x, it become
Data
0x10002
0x30004
...
0x50006
Modbus RTU function code:
0x
0x01 Read coil
0x_multi_coils 0x01 Read coil
1x
0x02 Read discrete input
0x05 write single coil
0x0f write multiple coil
N/A for write operation
3x
4x
N/A for write operation
0x10 write multiple register
0x04 Read input register
0x03 Read holding register
5x
0x03 Read holding register
0x10 write multiple register
( note: reverse word order in double word format)
3xbit is equivalent to 3x
4xbit is equivalent to 4x
6x
0x03 Read holding register
0x06 write single register
( note: use 6x device is limited to device of one word only )
Wiring diagram:
MODBUS RS232 PORT
MT8000 RS-232
Modbus RTU
9P D-SUB
Controller RS232
COM1
COM2
COM3
Port
TX
TX
TX
RXD
RX
RX
RX
TXD
GND
GND
GND
GND
RTS
CTS
206
MODBUS RS422/485 PORT
MT8000
Modbus RTU Controller
COM1 RS-485 4w
RS422 Port
RX-
TX-
RX+
TX+
TX-
RX-
TX+
RX+
GND
GND
MT8000 RS-485 2Wire
Modbus RTU
9P D-SUB
Controller RS485
COM1
COM3
RX-
Data-
D-
RX+
Data+
D+
GND
GND
GND
Driver Version:
Version
Date
V1.70
Aug/26/2009
V1.80
V1.90
Description of Changes
To turn LB9200 off when return code is error.
Dec/24/2009
Fixed when receiving data from modbus rtu over 8 bytes, LW9570
can not calculate correctly.
207
MODBUS RTU (zero-based addressing)
MODBUS RTU CONTROLLER
http://www.modbus.org
HMI Setting:
Parameters
Recommend
Option
PLC type
Modbus RTU
Com port
RS485
RS232/RS485
Baud rate
9600
9600~115200
Parity bit
Even
Even, Odd, None
Data Bits
7,8
Stop Bits
1,2
HMI Station No.
PLC Station No.
Notes
Does not apply to this protocol
0-255
Online Simulator
YES
Extend address mode
YES
Broadcast command
YES
PLC Setting:
Communication mode
Modbus RTU protocol
Device address:
Bit/Word
Device Type
Format
Range
0x
ddddd
0-65535
Output bit
1x
ddddd
0-65535
Input bit (read only)
0x_multi_coils
ddddd
1-65535
Write Multiple Coils
3x_Bit
ddddd(dd)
0-6553515
Input Register bit (read only)
4x_Bit
ddddd(dd)
0-6553515
Output Register bit
3x
ddddd
0-65535
Input Register (read only)
4x
ddddd
0-65535
Output Register
DW
5x
ddddd
0-65535
4x double word swap
6x
ddddd
0-65535
4x single word write
208
Memo
NOTE:
Address type 5x are mapping to Hold Reg. The communication protocol of 5x almost same as
4x except 5xmaking double word swap.
If 4x have following information
Address
Data in word
0x1
0x2
0x3
0x4
0x5
0x6
Data
0x20001
0x40003
0x60005
Address
Data in word
0x2
0x1
0x4
0x3
0x6
0x5
...
For 5x, it become
Data
0x10002
0x30004
...
0x50006
Modbus RTU function code:
0x
0x01 Read coil
0x_multi_coils 0x01 Read coil
1x
0x02 Read discrete input
0x05 write single coil
0x0f write multiple coil
N/A for write operation
3x
4x
N/A for write operation
0x10 write multiple register
0x04 Read input register
0x03 Read holding register
5x
0x03 Read holding register
0x10 write multiple register
(Note: reverse word order in double word format)
3xbit is equivalent to 3x
4xbit is equivalent to 4x
6x
0x03 Read holding register
0x06 write single register
(Note: use 6x device is limited to device of one word only)
Wiring diagram:
MODBUS RS232 PORT
MT8000 RS-232
Modbus RTU
9P D-SUB
Controller RS232
COM1
COM2
COM3
Port
TX
TX
TX
RXD
RX
RX
RX
TXD
GND
GND
GND
GND
RTS
CTS
209
MODBUS RS422/485 PORT
MT8000
Modbus RTU Controller
COM1 RS-485 4w
RS422 Port
RX-
TX-
RX+
TX+
TX-
RX-
TX+
RX+
GND
GND
MT8000 RS-485 2Wire
Modbus RTU
9P D-SUB
Controller RS485
COM1
COM3
RX-
Data-
D-
RX+
Data+
D+
GND
GND
GND
Note: MODBUS RTU (adjustable) usage
Users can decide the address range via setting value on Parameter 1. For example, when users set 5
to Parameter 1, the address range become 5~65535.
210
Driver Version:
Version
Date
V1.30
Aug/26/2009
Description of Changes
211
MODBUS SERVER (Modbus RTU Slave)
HMI Setting:
Parameters
Recommend
Option
Option
PLC type
Modbus Server
Com port
RS232
RS232, RS485
Ethernet
Baud rate
9600
9600~115200
Parity bit
Even
Even, Odd, None
Data Bits
Stop Bits
HMI Station No.
PLC Station No.
Notes
0
1-31
Port no.
HMI Modbus station No.
502
Online Simulator
YES
Broadcast command
NO
Extend address mode
NO
PLC Setting:
Communication mode
Modbus RTU protocol
Device address:
Bit/Word
Device Type
Format
Range
Memo
LB
dddd
0~9998
Mapping to 0x/1x 1~9999
LW
dddd
0~9998
Mapping to 3x/4x 1~9999
RW
ddddd
0~55536
Mapping to 3x/4x 10000~65536
LB0 = 0x0001, LB1 = 0x0002, LW0 = 3x0001, LW1 = 3x0002
Modbus RTU Server doesnt support function Code 06(to preset single register), please use function code 16(0x10,
preset multiple register).
212
Wiring diagram:
RS-232:
Modbus RTU RS232
9P D-SUB
MT8000 RS232
9P D-SUB
COM1
COM2
COM3
3 TX
2 RX
5 GND
4 TX
6 RX
5 GND
7 TX
8 RX
5 GND
RX
TX
GND
RS-485:
MT8000 RS485 2w
Modbus RTU RS-485
9P D-SUB
9P D-SUB
COM1
COM3
RX-
Data-
Data-
RX+
Data+
Data+
GND
GND
GND
Precaution: Setting more than one Modbus server in HMI device list is useless.
Driver Version:
Version
Date
V1.00
Dec/30/2008
Description of Changes
213
MODBUS TCP/IP
Modbus RTU TCP/IP device.
http://www.modbus.org
HMI Setting:
Parameters
Recommend
Option
PLC type
MODBUS TCP/IP
Com port
Ethernet
HMI Station No.
Does not apply
PLC Station No.
0~255
TCP/IP port
502
Notes
PLC Setting:
Communication mode
Device address:
Bit/Word
Device Type
Format
Range
0x
ddddd
1-65535
Output bit
0x_multi_coils
ddddd
1-65535
Write Multiple Coils
1x
ddddd dd
1-65535
Input bit (read only)
3x_bit
ddddd dd
100-6553515
Input Register bit (read only)
4x_bit
ddddd dd
100-6553515
Output Register bit
6x_bit
ddddd dd
100-6553515
Output Register bit
3x
Ddddd
1-65535
Input Register (read only)
4x
Ddddd
1-65535
Output Register
DW
5x
Ddddd
1-65535
4x double word swap
6x
Ddddd
1-65535
4x single word write
214
Memo
Wiring diagram:
Ethernet::
Wire color
MT8000 Ethernet
Ethernet Hub or Switch
RJ45
RJ45
TX+
White/Orange
RX+
TX-
Orange
RX-
RX+
White/Green
TX+
BD4+
Blue
BD4+
BD4-
White/Blue
BD4-
RX-
Green
TX-
BD3+
White/Brown
BD3+
BD3-
Brown
BD3-
Ethernet: Direct connect (crossover cable)
Wire color
MT8000 Ethernet
Modbus TCP Device
RJ45
RJ45
TX+
White/Orange
RX+
TX-
Orange
RX-
RX+
White/Green
TX+
BD4+
Blue
BD4+
BD4-
White/Blue
BD4-
RX-
Green
TX-
BD3+
White/Brown
BD3+
BD3-
Brown
BD3-
Driver Version:
Version
Date
V1.50
Aug/26/2009
Description of Changes
215
8
RJ45
connector
MODBUS TCP/IP
Modbus RTU TCP/IP device.
http://www.modbus.org
HMI Setting:
Parameters
Recommend
Option
PLC type
MODBUS TCP/IP
Com port
Ethernet
HMI Station No.
Does not apply
PLC Station No.
0~255
TCP/IP port
502
Notes
PLC Setting:
Communication mode
Device address:
Bit/Word
B
B
B
B
B
B
W
W
DW
W
Device Type
1x
0x
0x_multi_coils
3x_bit
4x_bit
6x_bit
3x
4x
5x
6x
Format
ddddd
ddddd dd
ddddd
ddddd dd
ddddd dd
Ddddd dd
ddddd
ddddd
ddddd
ddddd
Range
1-65535
1-65535
1-65535
100-6553515
100-6553515
100-6553515
1-65535
1-65535
1-65535
1-65535
216
Memo
Output bit
Input bit
Write Multiple Coils
Input Register bit (read only)
Output Register bit
Output Register bit
Input Register
Output Register
4x double word swap
4x single word write
Wiring diagram:
Ethernet:
MT8000 Ethernet
RJ45
Wire color
Ethernet Hub or Switch
RJ45
TX+
White/Orange
RX+
TX-
Orange
RX-
RX+
White/Green
TX+
BD4+
Blue
BD4+
BD4-
White/Blue
BD4-
RX-
Green
TX-
BD3+
White/Brown
BD3+
BD3-
Brown
BD3-
Ethernet: Direct connect (crossover cable)
MT8000 Ethernet
RJ45
Wire color
Modbus TCP Device
RJ45
TX+
White/Orange
RX+
TX-
Orange
RX-
RX+
White/Green
TX+
BD4+
Blue
BD4+
BD4-
White/Blue
BD4-
RX-
Green
TX-
BD3+
White/Brown
BD3+
BD3-
Brown
BD3-
217
RJ45
connector
MODBUS TCP/IP 32bit
Modbus RTU TCP/IP device.
http://www.modbus.org
HMI Setting:
Parameters
Recommend
Option
PLC type
MODBUS TCP/IP
Com port
Ethernet
HMI Station No.
Does not apply
PLC Station No.
0~255
TCP/IP port
502
Notes
PLC Setting:
Communication mode
Device address:
Bit/Word
B
B
B
B
B
B
W
W
DW
W
W
Device Type
1x
0x
0x_multi_coils
3x_bit
4x_bit
6x_bit
3x
4x
5x
6x
4x_32Bit
Format
ddddd
ddddd dd
ddddd
ddddd dd
ddddd dd
ddddd dd
ddddd
ddddd
ddddd
ddddd
ddddd
Range
1-65535
1-65535
1-65535
100-6553515
100-6553515
100-6553515
1-65535
1-65535
1-65535
1-65535
1-65535
218
Memo
Output bit
Input bit
Write Multiple Coils
Input Register bit (read only)
Output Register bit
Output Register bit
Input Register
Output Register
4x double word swap
4x single word write
4x High/low byte swap
Wiring diagram:
Ethernet:
MT8000 Ethernet Wire color
RJ45
Ethernet Hub or Switch
RJ45
TX+
White/Orange
RX+
TX-
Orange
RX-
RX+
White/Green
TX+
BD4+
Blue
BD4+
BD4-
White/Blue
BD4-
RX-
Green
TX-
BD3+
White/Brown
BD3+
BD3-
Brown
BD3-
Ethernet: Direct connect (crossover cable)
MT8000 Ethernet Wire color
RJ45
Modbus TCP Device
RJ45
TX+
White/Orange
RX+
TX-
Orange
RX-
RX+
White/Green
TX+
BD4+
Blue
BD4+
BD4-
White/Blue
BD4-
RX-
Green
TX-
BD3+
White/Brown
BD3+
BD3-
Brown
BD3-
219
RJ45
connector
MODBUS TCP/IP (zero-based)
Modbus RTU TCP/IP device.
http://www.modbus.org
HMI Setting:
Parameters
Recommend
Option
PLC type
MODBUS TCP/IP
Com port
Ethernet
HMI Station No.
Does not apply
PLC Station No.
0~255
TCP/IP port
502
Notes
PLC Setting:
Communication mode
Device address:
Bit/Word
Device Type
Format
Range
Memo
0x
ddddd
0-65535
Output bit
1x
ddddd dd
0-65535
Input bit (read only)
3x_bit
ddddd dd
0-6553515
Input Register bit (read only)
4x_bit
ddddd
0-6553515
Output Register bit
3x
ddddd
0-65535
Input Register (read only)
4x
ddddd
0-65535
Output Register
DW
5x
ddddd
0-65535
4x double word swap
Wiring diagram:
Ethernet::
MT8000 Ethernet
Wire color
Ethernet Hub or Switch
RJ45
RJ45
TX+
White/Orange
RX+
TX-
Orange
RX-
RX+
White/Green
TX+
BD4+
Blue
BD4+
BD4-
White/Blue
BD4-
RX-
Green
TX-
BD3+
White/Brown
BD3+
220
RJ45
connector
BD3-
Brown
BD3-
Ethernet: Direct connect (crossover cable)
Wire color
MT8000 Ethernet
Modbus TCP Device
RJ45
RJ45
TX+
White/Orange
RX+
TX-
Orange
RX-
RX+
White/Green
TX+
BD4+
Blue
BD4+
BD4-
White/Blue
BD4-
RX-
Green
TX-
BD3+
White/Brown
BD3+
BD3-
Brown
BD3-
Driver Version:
Version
Date
V1.40
Aug/27/2009
Description of Changes
221
Moeller XC-CPU101
MOELLER XC100/200 series
http://www.moeller.net
HMI Setting:
Parameters
Recommend
Option
PLC type
Moeller XC-CPU101
Com port
RS232
Baud rate
38400
Parity bit
None
Data Bits
Stop Bits
HMI Station No.
PLC Station No.
Notes
4800~57600
PLC Setting:
Communication mode
Device address:
Bit/Word
B
B
W
W
W
Device Type
QX
IX
MW
QW
IW
Format
ddo
ddo
dddd
dd
dd
Range
dd:0~15, o:0~7
dd:0~15, o:0~7
1~4095
0~15
0~15
Wiring diagram:
RS-232:
CPU RS-232
8P RJ45
MT8000 RS232
9P D-SUB
COM1
COM2
COM3
3 TX
2 RX
5 GND
4 TX
6 RX
5 GND
7 TX
8 RX
5 GND
8
5
4
222
RD
TD
GND
RJ45
connector
Driver Version:
Version
Date
1.00
Apr/01/2010
Description of Changes
223
Modicon Twido
http://www.modicon.com/
HMI Setting:
Parameters
PLC type
Com port
Baud rate
Parity bit
Data Bits
Stop Bits
HMI Station No.
PLC Station No.
Recommend
Modbus RTU
RS485
19200
None
8
1
0
1
Option
RS232/RS485
19200
Even, Odd, None
8
1
0-247
Notes
Support Extended Address mode.
Must match the PLCs port setting.
Must match the PLCs port setting.
Must match the PLCs port setting.
Must set 8 for RTU mode
Must set 8 for RTU mode
Does not apply to this protocol.
Must match the PLCs port setting.
PLC Setting:
Communication mode
19200, None, 8, 1
Modbus RTU Slave
Select
Device address:
Bit/Word
B
W
Device
Type
0x or 1x
3x or 4x
Format
Range
Memo
dddd
dddd
0~9999
0~9999
%Mi
%MWi
224
Wiring diagram:
MT8000 RS-485
9P D-SUB
COM1
Port 1 RS485 port
8P mini-din Female
COM3
RX-
Data-
B(-)
RX+
Data+
A(+)
GND
GND
DTP
7 GND
MT8000 RS-485
9P D-SUB
COM1
Port2 RS485 port
3Pin Terminal
COM3
RX-
RX+
GND
Data-
Data+
GND
B(-)
A(+)
GND
MT8000 RS232
9P D-SUB Female
COM1
COM2
COM3
Port2 RS232
9P D-SUB Female
TX
4 TX
7 TX
RX
RX
6 RX
8 RX
TX
5 GND
5 GND
GND
5 GND
225
8Pin miniDin Female
OMRON C/CQM1 series
OMRON C, CPM, CPL, CQM Series (Host Link Protocol),
http://oeiweb.omron.com/oei/Products-PLC.htm
HMI Setting:
Parameters
Recommend
PLC type
OMRON C/CQM1
Option
Notes
Series
Com port
RS232
RS232, RS422, RS485
Baud rate
9600
9600, 19200
Parity bit
Even
Even, Odd, None
Data Bits
7 or 8
Stop Bits
1 or 2
HMI Station No.
PLC Station No.
0-31
Online Simulator
YES
Extend address mode
YES
Host Link Station No.
Broadcast command
YES
PLC Setting:
Communication mode
Host Link protocol
Device address:
Bit/Word
Device
Type
Format
Range
IR
ddd(dd)
0-409515
I/O and internal Relay
HR
ddd(dd)
0-409515
Hold Relay
AR
ddd(dd)
0-409515
Auxiliary Relay
LR
ddd(dd)
0-409515
Link Relay
TC
ddd
0-519
Timer/Counter Register
DM
dddd
0-6659
Data register
226
Memo
Wiring diagram:
CPU Port(CPM2A,CQM1/1H,C200H/HS/ALPHA series)
Communication Module:
CPM1-CIF01 adapter(for CPM1/CPM1A/CPM2A series,CQM1/CQM1H series)
CPM1H-SCB41 communication module(for CQM1H-CPU51/61)
OMRON
CPU RS-232 9P
D-SUB Female
MT8000 RS232
9P D-SUB Female
COM1
COM2
COM3
3 TX
2 RX
5 GND
4 TX
6 RX
5 GND
7 TX
8 RX
5 GND
RD
SD
GND
RS
CS
C200h-LK201,3G2A6-LK201 communication module
C200HW-COM02/03/04/05/06 communication module
OMRON
CPU RS-232 9P
D-SUB Female
MT8000 RS232
9P D-SUB Female
COM1
COM2
COM3
3 TX
2 RX
5 GND
4 TX
6 RX
5 GND
7 TX
8 RX
5 GND
Driver Version:
Version
Date
V1.60
Sep/25/2009
Description of Changes
227
RD
SD
GND
RS
CS
OMRON CJ1/CS1
OMRON CP1L, CP1H, CJ1M, CJ1H, CJ1G, CS1H and CS1G. (Host Link Protocol FINS
command), this driver supports Extend Addressing mode.
http://oeiweb.omron.com/oei/Products-PLC.htm
HMI Setting:
Parameters
Recommend
Option
PLC type
OMRON CJ1/CS1
Com port
RS232
RS232, RS422, RS485
Baud rate
9600
9600~115200
Parity bit
Even
Even, Odd, None
Data Bits
7 or 8
Stop Bits
1 or 2
HMI Station No.
PLC Station No.
Notes
0-31
Online Simulator
YES
Broadcast command
NO
Host Link Station No.
Extend address mode
YES
PLC Setting:
Communication mode
Host Link protocol
Device address:
Bit/Word
Device Type
Format
Range
Bit
D_bit
ddd(dd)
ddd:0~32767 (dd): 0~15
Data Memory (DM)
Bit
H_bit
ddd(dd)
ddd:0~511 (dd): 0~15
Holding Area (HR)
Bit
W_bit
ddd(dd)
ddd:0~511 (dd): 0~15
Work Area (WR)
Bit
CIO_bit
ddd(dd)
ddd:0~6143 (dd): 0~15
Channel I/O (CIO)
Bit
A_bit
ddd(dd)
ddd:0~959 (dd): 0~15
Auxiliary Relay (AR)
Bit
T_bit
ddd
ddd:0~4095
Timer (TIM)
Bit
C_bit
ddd
ddd:0~4095
Counter (CNT)
Word
ddd
ddd:0~32767
Data Memory (DM)
Word
ddd
ddd:0~511
Holding Area (HR)
228
Memo
Bit/Word
Device Type
Format
Range
Memo
Word
ddd
ddd:0~511
Work Area (WR)
Word
CIO
ddd
ddd:0~6143
Channel I/O (CIO)
Word
ddd
ddd:0~959
Auxiliary Relay (AR)
Word
ddd
ddd:0~4095
Timer (TIM)
Word
ddd
ddd:0~4095
Counter (CNT)
Word
EM0~EMC
dddd
dddd:0-6149
Extend Memory
Wiring diagram:
RS-232:
OMRON
CPU RS-232 9P
D-SUB Female
MT8000 RS232
9P D-SUB Female
COM1
COM2
COM3
TX
TX
TX
RD
RX
RX
RX
SD
GND
GND
RS
CS
GND
GND
CP1H/CP1L CP1W-CIF11 RS422
MT8000
CP1W-CIF11
COM1 [RS-485] 4w
RS422 Port
9P D-SUB Male
1
RX-
SDA
RX+
SDB
TX-
RDA
TX+
RDB
GND
FG
Driver Version:
Version
Date
V1.40
Arp/17/2009
Description of Changes
229
CP1W-CIF11
SW1 ON
OFF
OFF
OFF
OFF
OFF
OMRON CJ1/CS1 Ethernet
OMRON CJ1M, CJ1H, CJ1G, CS1H and CS1G. (Ethernet FINS),
http://oeiweb.omron.com/oei/Products-PLC.htm
HMI Setting:
Parameters
Recommend
PLC type
OMRON CJ1/CS1
Option
Notes
(Ethernet)
Com port
Ethernet
TCP port
9600
HMI Station No.
PLC Station No.
PLC Setting:
Communication mode
FINS Ethernet protocol
Device address:
Bit/Word
Device Type
Format
Range
Memo
D_bit
ddddd(dd)
ddd:0~32767 (dd): 0~15
Data Memory (DM)
H_bit
ddd(dd)
ddd:0~511 (dd): 0~15
Holding Area (HR)
W_bit
ddd(dd)
ddd:0~511 (dd): 0~15
Work Area (WR)
CIO_bit
dddd(dd)
ddd:0~6143 (dd): 0~15
Channel I/O (CIO)
A_bit
ddd(dd)
ddd:0~959 (dd): 0~15
Auxiliary Relay (AR) (Read only)
T_bit
dddd
ddd:0~4095
Timer (TIM)
C_bit
dddd
ddd:0~4095
Counter (CNT)
ddddd
ddd:0~32767
Data Memory (DM)
ddd
ddd:0~511
Holding Area (HR)
ddd
ddd:0~511
Work Area (WR)
CIO
dddd
ddd:0~6143
Channel I/O (CIO)
ddd
ddd:0~959
Auxiliary Relay (AR) (Read only)
dddd
ddd:0~4095
Timer (TIM)
dddd
ddd:0~4095
Counter (CNT)
230
Wiring diagram:
Ethernet:
MT8000 Ethernet
Wire color
Ethernet Hub or Switch
RJ45
RJ45
TX+
White/Orange
RX+
TX-
Orange
RX-
RX+
White/Green
TX+
BD4+
Blue
BD4+
BD4-
White/Blue
BD4-
RX-
Green
TX-
BD3+
White/Brown
BD3+
BD3-
Brown
BD3-
Ethernet: Direct connect (crossover cable)
MT8000 Ethernet
Wire color
OMRON Ethernet
RJ45
RJ45
TX+
White/Orange
RX+
TX-
Orange
RX-
RX+
White/Green
TX+
BD4+
Blue
BD4+
BD4-
White/Blue
BD4-
RX-
Green
TX-
231
RJ45
connector
BD3+
White/Brown
BD3+
BD3-
Brown
BD3-
Driver Version:
Version
Date
V1.00
Dec/30/2008
Description of Changes
232
OMRON E5CN
OMRON E5CN series Temperature controller with communication option.
E5EN/CN/GN series
http://oeiweb.omron.com
HMI Setting:
Parameters
Recommend
PLC type
OMRON E5CN
Com port
RS485 2W
Baud rate
9600
Option
Notes
9600/19200/38400/57600
/115200
Parity bit
Even
Even, Odd, None
Data Bits
7,8
Stop Bits
1,2
HMI Station No.
PLC Station No.
Does not apply to this protocol
0-99
Online Simulator
YES
Extend address mode
YES
Broadcast command
YES
PLC Setting:
Communication mode
9600, Even, 7, 2 (default)
Device address:
Bit/Word
Device Type
Format
Range
Status
dd
0-31
Page40
DW
C0
hhhh
0-5
Read only (Hex) Page34
DW
C1
hhhh
0-1C
Read/Write (Hex) Page35
DW
C3
hhhh
0-1D
Read/Write (Hex) Page36
Operation00_00
hh
Communications writing OFF (disabled)
Operation00_01
hh
Communications writing ON(Enabled)
Operation01_00
hh
Run
Operation01_01
hh
Stop
Operation02_00
hh
Multi-SP Set point 0
233
Memo
Bit/Word
Device Type
Format
Range
Memo
Operation02_01
hh
Multi-SP Set point 1
Operation02_02
hh
Multi-SP Set point 2
Operation02_03
hh
Multi-SP Set point 3
Operation03_00
hh
AT cancel
Operation03_01
hh
AT execute
Operation04_00
hh
Write mode (Backup)
Operation04_01
hh
Write mode (Ram)
Operation05_00
hh
Save RAM data
Operation06_00
hh
Software reset
Operation07_00
hh
Move to setup area 1
Operation08_00
hh
Move to protect level
Wiring diagram:
MT8000 RS-485 2Wire
OMRON E5CN
9P D-SUB
COM1
COM3
RX-
Data-
12
RX+
Data+
11
GND
GND
GND
Driver Version:
Version
Date
V1.20
Sep/16/2009
Description of Changes
234
Panasonic FP
NAIS(Matsushita) FP series include FP-X, FP-, FP0, FP1, FP2, FP2SH, FP10SH and FP3
Ethernet support FP-X with AFPX-COM5.
http://pewa.panasonic.com/
HMI Setting:
Parameters
Recommend
Option
Notes
PLC type
Panasonic FP
Com port
RS232
RS232/RS485 Ethernet
Must match the PLCs port setting.
Baud rate
9600
9600, 19200, 38400, 57600,
Must match the PLCs port setting.
115200
Parity bit
Odd
Even, Odd, None
Must match the PLCs port setting.
Data Bits
7 or 8
Must match the PLCs port setting.
Stop Bits
1 or 2
Must match the PLCs port setting.
HMI Station No.
0-255
Does not apply to this protocol.
PLC Station No.
0-255
Must match the PLCs port setting.
FP3 must set 0.
PLC Setting:
Communication
mode
9600,O,8,1(default)
Device address:
Bit/Word
Device
Type
Format
dddd(h)
0~9999F
Input(X)
dddd(h)
0~9999F
Output(Y)
dddd(h)
0~9999F
Internal Relay(R)
dddd
0~9999
Link Relay(L)
L_Bit
dddd(h)
0~9999F
dddd
0~9999
Timer(T)
dddd
0~9999
Counter(C)
SV
dddd
0~9999
Timer/Counter set value(SV)
EV
ddddd
0~65535
Timer/Counter elapse
DT
ddddd
0~99999
Data Register(DT)
LD
dddd
0~8447
Link Register(LD)
Range
Memo
value(EV)
235
WX
dddd
0~9999
Input(WX) (read only)
WY
dddd
0~9999
Output(WY)
WR
dddd
0~9999
Internal Relay(WR)
WL
dddd
0~9999
Link Relay(WL)
FL
ddddd
0~99999
File register(FL)
Wiring diagram:
MT8000 RS232
FP0, FP2, FP2SH,FPM
9P D-SUB
CPU Tool port
5P mini DIN RS-232
COM1
COM2
COM3
TX
TX
TX
RXD
RX
RX
RX
TXD
Mini Din 5 Pin
GND
GND
Female
GND
GND
MT8000 RS232
FP0 CPU RS232
9P D-SUB
3P terminal
COM1
COM2
COM3
TX
TX
TX
RX
RX
RX
GND
GND
GND
MT8000 RS232
FP1, FP2, FP2SH,FP10SH CPU
9P D-SUB
9p D-SUB Male RS232
COM1
COM2
COM3
TX
TX
TX
RXD
RX
RX
RX
TXD
GND
GND
RTS
CTS
CD
ER
GND
GND
236
MT8000
FP1 CPU RS422 port
COM1[RS-485]4w 9P
Hirose 8Pin Port
D-SUB
1 RX-
TXDA
2 RX+
TXDB
3 TX-
RXDA
4 TX+
RXDB
5 GND
GND
Hirose 8Pin Port
MT8000
FP3 CPU RS422 port
COM1[RS-485]4w 9P
15P D-SUB Female
D-SUB
1 RX-
TXDA
2 RX+
TXDB
3 TX-
10
RXDA
4 TX+
RXDB
5 GND
GND
RTS+
CTS+
11
RTS12
CTS-
Driver Version:
Version
Date
V1.40
Jul/23/2009
V1.80
Apr/12/2010
Description of Changes
Add FL device type
237
Panasonic FP Ethernet
NAIS(Matsushita) FP series include FP-X, FP-, FP0, FP1, FP2, FP2SH, FP10SH and FP3
Ethernet support FP-X with AFPX-COM5.
http://pewa.panasonic.com/
HMI Setting:
Parameters
Recommend
PLC type
Panasonic FP
Com port
Ethernet
Port no.
Option
Notes
9094
PLC Station no.
0~255
PLC Setting:
Communication mode
Device address:
Bit/Word
Device
Type
Format
dddd(h)
0~9999F
Input(X)
dddd(h)
0~9999F
Output(Y)
dddd(h)
0~9999F
Internal Relay(R)
dddd
0~9999
Link Relay(L)
L_Bit
dddd(h)
0~9999F
dddd
0~9999
Timer(T)
dddd
0~9999
Counter(C)
SV
dddd
0~9999
Timer/Counter set value(SV)
EV
ddddd
0~65535
Timer/Counter elapse value(EV)
DT
ddddd
0~99999
Data Register(DT)
LD
dddd
0~8447
Link Register(LD)
WX
dddd
0~9999
Input(WX) (read only)
WY
dddd
0~9999
Output(WY)
WR
dddd
0~9999
Internal Relay(WR)
WL
dddd
0~9999
Link Relay(WL)
FL
ddddd
0~99999
File register(FL)
Range
238
Memo
Wiring diagram:
Ethernet:
MT8000 Ethernet Wire color
RJ45
1
TX+
White/Orange
Ethernet Hub or
Switch RJ45
RX+
1
TX-
Orange
RX+
White/Green
TX+
BD4+
Blue
BD4+
BD4-
White/Blue
BD4-
RX-
Green
TX-
BD3+
White/Brown
BD3+
BD3-
Brown
BD3-
RXRJ45
Ethernet: Direct connect (crossover cable)
MT8000 Ethernet Wire color
RJ45
XGL-EFMT
RJ45
TX+
White/Orange
RX+
TX-
Orange
RX-
RX+
White/Green
TX+
BD4+
Blue
BD4+
BD4-
White/Blue
BD4-
RX-
Green
TX-
BD3+
White/Brown
BD3+
BD3-
Brown
BD3-
239
Ethernet connect
TCP port: 9094
Ethern
et
MT8000
RS232
AFPX-COM5
Driver Version:
Version
Date
1.80
April. 12.2010
Description of Changes
240
FP-X
Panasonic FP2 (Ethernet)
NAIS(Matsushita) FP2 series include FP2, FP2SH, FP10SH CPU.
http://pewa.panasonic.com/
HMI Setting:
Parameters
Recommend
PLC type
Panasonic FP
Com port
Ethernet
Port no.
Option
Notes
8500
PLC Station no.
0~255
PLC Setting:
Communication mode
Device address:
Bit/Word
Device
Type
Format
Range
Memo
dddd(h)
0~9999F
Input(X)
dddd(h)
0~9999F
Output(Y)
dddd(h)
0~9999F
Internal Relay(R)
dddd
0~9999
Link Relay(L)
L_Bit
dddd(h)
0~9999F
dddd
0~9999
Timer(T)
dddd
0~9999
Counter(C)
SV
dddd
0~9999
Timer/Counter set value(SV)
EV
ddddd
0~65535
Timer/Counter elapse value(EV)
DT
ddddd
0~99999
Data Register(DT)
LD
dddd
0~8447
Link Register(LD)
WX
dddd
0~9999
Input(WX) (read only)
WY
dddd
0~9999
Output(WY)
WR
dddd
0~9999
Internal Relay(WR)
WL
dddd
0~9999
Link Relay(WL)
241
Wiring diagram:
Ethernet:
MT8000 Ethernet Wire color
RJ45
1
TX+
White/Orange
Ethernet Hub or
Switch RJ45
RX+
1
TX-
Orange
RX+
White/Green
TX+
BD4+
Blue
BD4+
BD4-
White/Blue
BD4-
RX-
Green
TX-
BD3+
White/Brown
BD3+
BD3-
Brown
BD3-
RXRJ45
Ethernet: Direct connect (crossover cable)
MT8000 Ethernet Wire color
RJ45
XGL-EFMT
RJ45
TX+
White/Orange
RX+
TX-
Orange
RX-
RX+
White/Green
TX+
BD4+
Blue
BD4+
BD4-
White/Blue
BD4-
RX-
Green
TX-
BD3+
White/Brown
BD3+
BD3-
Brown
BD3-
242
Driver Version:
Version
Date
1.00
March. 15.2010
Description of Changes
243
Panasonic MINAS A4 Series
Panasonic MINAS A4 series Servo Drive
HMI Setting:
Parameters
Recommend
PLC type
PANASONIC MINAS A4
Com port
RS232
Axis no.
0 (master station only)
Baud rate
9600
Parity bit
None
Data Bits
Stop bit
Option
Notes
0 ~ F (slave)
Device address:
Bit/Word
Device Type
Format
Range
Memo
Command 01
0~0
cpu version (Numeric format:16-bit Hex)
Command 05
0~0
driver version (ASCII / 12 words)
Command 06
0~0
motor version (ASCII / 12 words)
Command 20
0~7
States (Note 3)
Command 21
0~0
Command 22
0~0
Command 24
0~0
Command 25
0~0
Command 26
0~0
Command 27
0 ~ 31
input signal (Note 3)
Command 28
0 ~ 31
output signal (Note 3)
Command 84
0~0
write parameter to EEPROM (Note 1)
Command 90
0~0
command pulse counter
(Numeric format: 32-bit Signed)
feedback pulse counter
(Numeric format: 32-bit Signed)
present speed
(Numeric format: 16-bit Unsigned)
present torque
(Numeric format: 16-bit Unsigned)
present deviation counter
(Numeric format: 32-bit Signed)
present Alarm Data
(Numeric format: 16-bit Unsigned)
244
Alarm History (Note 4)
Command 91
1 ~ 14
Command 92
1 ~ 14
Command 93
0~0
Command 94
0~0
alarm clear (Note 1)
Command 9B
0~0
Absolute clear (Note 1)
Parameter
hh
0 ~ 7F
(Numeric format: 16-bit Unsigned)
Batch Alarm (Note 4)
(Numeric format: 16-bit Unsigned)
clear alarm history (include EEPROM)
(Note 1)
Individual Parameter (range: 0x00 ~ 0x7F)
(Note 2)
Note:
1.
Command 84,Command 93,Command 94 and Command 9B are write only.(These commands are able to use Set
Bit Object and execute the write command after trigger Set Bit Object.). Except these four commands, others are
read only.
2.
Parameter read/write: Use Device type to define address control from 00~7F
For example: address_00 is mapping to Parameter_00. (Please refer detail with Panasonic
MINAS A4 series user manual.)
3.
Device address type can define MINAS A4 Drivers command list.
Command 20, Command 27 and Command 28 are Bit type, use Operating range to map communication order
status.
For example: Command 20_3 means Read state_CCW.
(Please refer detail with Panasonic MINAS A4 series user manual)
4.
Command 91 and Command 92 are word type, use Operating range to map the record of 14 alarms.
For example: Command 91_1 means Read alarm data_First alarm.
Wiring diagram:
MT8000 RS232
9P D-SUB
MINAS A4 Driver
8p Mini-DIN Male CNX4
Port / RS232
COM1
COM2
COM3
3 TX
4 TX
7 TX
RXD
2 RX RRX 6 RX
8 RX
TXD
5 GND
5 GND
GND
5 GND
MT8000 RS485 2w
9P D-SUB
MINAS A4 Driver
8p Mini-DIN Male
MINAS A4 Driver
8p Mini-DIN Male
COM1
COM3
CNX3 Port/RS485 2w
CNX4 Port/RS485 2w
RX-
Data-
D-
D-
RX+
Data+
D+
D+
245
MINAS A4 Driver
CNX3 Port
8P Mini-Din Female
MINAS A4 Driver
CNX3 / CNX4 Port
D-
3 TX
D+
RX
GND
GND
D-
D+
RS485 cable / DVOP1970-005
MINAS A4 Driver
8p Mini-DIN Male
7
8
MINAS A4 Driver
8p Mini-DIN Male
DD+
MINAS A4 Driver
CNX4 Port
7
8
GND
RS232 cable / DVOP1960
MINAS A4 Driver
9P D-SUB Female
DD+
4
GND
MINAS A4 Driver
8p Mini-DIN Male
RXD
RXD
TXD
TXD
GND
GND
HMI connect with one Device
HMI connect with multi devices
246
Driver Version:
Version
Date
V0.01
Jul/23/2009
Description of Changes
247
Parker Compax3
Parker Compax3 Servo Drive
http://www.parker.com
HMI Setting:
RS232
Parameters
Recommend
Option
Notes
PLC type
Parker Compax3 [V1.50]
Com port
RS-232
Must match the PLCs port setting.
Baud rate
115200
Must match the PLCs port setting.
Parity bit
None
Even, Odd, None
Must match the PLCs port setting.
Data Bits
7 or 8
Must match the PLCs port setting.
Stop Bits
1 or 2
Must match the PLCs port setting.
PLC Station No.
Parameters
Recommend
Option
PLC type
Parker Compax3 [V1.50]
Com port
RS-485 2W
Must match the PLCs port setting.
Baud rate
9600
Must match the PLCs port setting.
Parity bit
None
Even, Odd, None
Must match the PLCs port setting.
Data Bits
7 or 8
Must match the PLCs port setting.
Stop Bits
1 or 2
Must match the PLCs port setting.
PLC Station No.
1-99
Must be 0 for RS232
RS485
Notes
Range from 1 to 99 for RS485,
according to the PLCs setting.
Device address:
Bit/Word
B
B
DW
DW
W
Device Type
R_Low16bit
R_High16bit
Register_Int
Register_float
Register_Short
Format
dddddddd(h)
dddddddd(h)
dddddd
dddddd
dddddd
248
Range
0~99999999(f)
0~99999999(f)
0~999999
0~999999
0~999999
Memo
For Register is INT32 or U32
For Register is INT32 or U32
For Register is INT16 or U16
Wiring diagram:
RS232:
EasyView MT8000
RS232 9P D-SUB
Parker Compax3 PLC
COM1 [RS232]
COM2 [RS232]
COM3 [RS232]
X10
9P D-SUB
TX
TX
TX
RXD
RX
RX
RX
TXD
GND
GND
GND
GND
RS485:
EasyView MT8000
RS-485 2w D-SUB
Parkar Compax3 PLC
COM1[485]
COM3[485]
X10
9P D-SUB
RX-
Data-
RXD
RX+
Data+
TXD
GND
GND
GND
Enable RS485
+5V
How to setting Compax 3 servo to RS485 mode?
1. Open C3 ServoManager2, select Communication=> RS-485 Settings.
2. Click to Configure RS-485/POP Settings.
249
3. Setting parameters as below
4. Downloading settings to Compax3 Servo.
5. Setting EB8000 system parameter and connecting with PLC for communication of HMI and
Servo.
Driver Version:
Version
Date
Description of Changes
V1.70
250
Parker SLVD Servo
Parker SLVD Servo, SLVD1N, SLVD2N, SLVD5N, SLVD7N, SLVD10N, SLVD15N,
SLVD17N.
http://www.parker.com/portal/site/PARKER/
HMI Setting:
Parameters
Recommend
Option
Notes
PLC type
Parker SLVD Series
Com port
RS485 4w
Baud rate
9600
9600/19200
must same as the PLC setting
Parity bit
Even
Even, Odd, None
must same as the PLC setting
Data Bits
7,8
must same as the PLC setting
Stop Bits
1,2
must same as the PLC setting
HMI Station No.
PLC Station No.
0-31
Online Simulator
YES
Extend address mode
PLC Setting:
Communication mode
9600,Even,8,1
Device address:
Bit/Word
Device Type
Format
Par_Binary
DDD(DD)
Par_One_Word
Par_One_Byte
Range
Memo
0~4999(15)
Set a bit of Parameter
DDD
0~4999
Set 2 bytes Parameter
DDD
0~4999
Set 1 byte Prarmeter
251
Bit/Word
Device Type
Format
DW
Par_Two_Word
DDD
Range
Memo
0~4999
Set 4 bytes Parameter
Wiring diagram:
Parker SLVD Servo
MT8000
COM1[RS-485]4w
Serial LINK X1
15P D-Sub
9P D-SUB
1
RX-
RX+
12
GND
GND
TX-
RX-
TX+
RX+
TER
TXTX+
Driver Version:
Version
Date
V1.00
Jan/28/2010
Description of Changes
252
SAIA PCD PGU mode
SAIA PCD series PGU mode.
http://www.saia-burgess.com/
HMI Setting:
Parameters
Recommend
Option
PLC type
SAIA PCD PGU mode
SAIA PCD S-BUS mode
Com port
RS232
RS232, RS485
Baud rate
9600
9600, 19200
Parity bit
Even
Even, Odd, None
Data Bits
7,8
Stop Bits
HMI Station No.
PLC Station No.
Notes
PDS driver
0-255
PLC Setting:
Communication mode
9600,E,7,1(default)
Device address:
Bit/Word
Device Type
Format
Range
Flag
ddd
ddd=0~8191
Input
ddd
ddd=0~511
Output
ddd
ddd=0~511
Register
ddd
ddd=0~4095
Counter
ddd
ddd=0~1599
Timer
ddd
ddd=0~450
Reg_Float
ddd
ddd=0~4095
253
Memo
support single float point
Wiring diagram:
RS232:
COM1
3
2
5
7
MT8000 RS232
SAIA PCD PGU port
9P D-SUB Male
9P D-SUB Female
COM2
COM3
TX
RX
GND
RTS
6 DSR(Of PGU Port):PGU connected
Driver Version:
Version
Date
V1.02
Dec/30/2008
Description of Changes
254
RXD
TXD
GND
DSR
RTS
CTS
SAIA PCD S-Bus mode
SAIA PCD series S-Bus mode.
http://www.saia-burgess.com/
HMI Setting:
Parameters
Recommend
PLC type
SAIA PCD S-BUS
Option
SAIA PCD PGU mode
Notes
PDS driver
mode
Com port
RS232
RS232, RS485
Baud rate
9600
9600, 19200, 38400
Parity bit
None
Even, Odd, None
Data Bits
7,8
Stop Bits
HMI Station No.
PLC Station No.
0-255
PLC Setting:
Communication mode
9600,N,8,1(default)
RS232
Port 0-Type:RS232
RS485 2W
S-BUS Mode:Data(S2),Port 1-Type:RS485
Device address:
Bit/Word
Device Type
Format
Range
Flag
ddd
ddd=0~8191
Input
ddd
ddd=0~511
Output
ddd
ddd=0~511
Register
ddd
ddd=0~4095
Counter
ddd
ddd=0~1599
Timer
ddd
ddd=0~450
Reg_Float
ddd
ddd=0~4095
255
Memo
support single float point
Wiring diagram:
RS232:
MT8000 RS232
SAIA PCD PGU port
9P D-SUB Male
9P D-SUB Female
COM1
COM2
COM3
3 TX
2 RX
5 GND
4 TX
6 RX
5 GND
7 TX
8 RX
5 GND
RXD
TXD
GND
RTS
CTS
RS485:
MT8000 RS-485
SAIA PCD1
9P D-SUB Female
Port# 1
COM1
COM3
RX-
Data-
11
RX+
Data+
12
GND
GND
MT8000 RS-485
SAIA PCD1
9P D-SUB Female
Port# 0
COM1
COM3
RX-
Data-
29
RX+
Data+
28
GND
GND
Driver Version:
Version
Date
V1.10
Dec/30/2009
Description of Changes
256
Schleicher XCX20C
Schleicher XCx-Systems Ethernet port.
Schleicher XCS series, 20C model
http://www.schleicher-electronic.com
HMI Setting:
Parameters
Recommend
PLC type
Schleicher XCS20
Com port
RS232
Baud rate
38400
Parity bit
Data Bits
Stop Bits
HMI Station No.
Option
Notes
PLC Station No.
Device address:
Bit/Word
B
B
B
W
W
W
DW
DW
DW
Device
Type
IX
QX
MX
IW
QW
MW
Format
Range
Memo
ddddd(o)
ddddd(o)
ddddd(o)
ddddd
ddddd
ddddd
ID
QD
ddddd
ddddd
MD
ddddd
ddd:0~65535 (o): 0~7
ddd:0~65535 (o): 0~7
ddd:0~65535 (o): 0~7
ddd:0~65535
ddd:0~65535
ddd:0~65535
ddd:0~65535
ddd:0~65535
ddd:0~65535
Input %IX
Output %QX
%MX
%IW
%QW
%MW
%ID
%QD
%WD
word address must be even.
257
Wiring diagram:
Schleicher XCS20
RS-232 X1
9P D-SUB Male
MT8000 RS232
9P D-SUB Female
COM1
COM2
COM3
TX
TX
TX
RD
RX
RX
RX
TD
GND
GND
GND
GND
Driver Version:
Version
Date
V1.00
Nov/30/2009
Description of Changes
258
Schleicher XCX 300
http://www.schleicher-electronic.com
HMI Setting:
Parameters
Recommend
PLC type
Schleicher XCX 300
Com port
Ethernet
Option
Notes
RS232,
RS422,
Ethernet
TCP Port no.
20547
HMI Station No.
PLC Station No.
PLC Setting:
Must create variable for HMI access.
Device address:
Bit/Word
B
B
B
W
W
W
DW
DW
DW
Device
Type
IX
QX
MX
IW
QW
MW
Format
Range
Memo
ddddd(o)
ddddd(o)
ddddd(o)
ddddd
ddddd
ddddd
ID
QD
ddddd
ddddd
MD
ddddd
ddddd:0~65535 (o): 0~7
ddddd:0~65535 (o): 0~7
ddddd:0~65535 (o): 0~7
ddddd:0~65535
ddddd:0~65535
ddddd:0~65535
ddddd:0~65535
ddddd:0~65535
ddddd:0~65535
Input %IX
Output %QX
%MX
%IW
%QW
%MW
%ID
%QD
%MD
* word address must be even.
259
Wiring diagram:
Ethernet: Direct connect (crossover cable)
MT8000 Ethernet
RJ45
Wire color
PLC
RJ45
TX+
White/Orange
RX+
TX-
Orange
RX-
RX+
White/Green
TX+
BD4+
Blue
BD4+
BD4-
White/Blue
BD4-
RX-
Green
TX-
BD3+
White/Brown
BD3+
BD3-
Brown
BD3-
Ethernet Hub:
MT8000 Ethernet
RJ45
Wire color
Ethernet Hub or Switch
RJ45
TX+
White/Orange
RX+
TX-
Orange
RX-
RX+
White/Green
TX+
BD4+
Blue
BD4+
BD4-
White/Blue
BD4-
RX-
Green
TX-
BD3+
White/Brown
BD3+
BD3-
Brown
BD3-
RS232 port
MT8000 RS-232
Schleicher xcx300
9P D-SUB
RS232 Port
COM1
COM2
COM3
TX
TX
TX
RXD
RX
RX
RX
TXD
GND
GND
GND
GND
260
8
RJ45
connector
RS422 port
MT8000
Schleicher xcx300
COM1 RS-485 4w
RS422 Port
RX-
TX-
RX+
TX+
TX-
RX-
TX+
RX+
GND
GND
Driver Version:
Version
Date
V1.00
Nov/30/2009
V1.10
Jul/1/2010
Description of Changes
Support RS232, RS422 interface connection
261
SEW Eurodrive MOVITRAC
SEW Eurodrive series, model MOVITRAC-07 inverter, MovitracB
http://sg.sew-eurodrive.com/
HMI Setting:
Parameters
Recommend
Option
PLC type
SEW Eurodrive MOVITRAC
Com port
RS-485
PLC Station
Notes
0~255
No.
Baud rate
9600
Data bit
Parity bit
Even
Stop bit
Device address:
Bit/Word
Device Type
Format
INDEX
DDDddddd
INDEX_Bit
DDDddddd(h)
Range
Memo
DDD(000~255)
D: Sub Index
ddddd(08000~25000)
d: Index
DDD(000~255)
D: Sub Index
ddddd(08000~25000)
h(0~f)
d: Index
h: Index_bit
The MOVITRAC-07 doesnt support Sub indexother series maybe support, please fixed to
input 000.
When input D and d, the correct format example as followSub index 15, Index 8359, Format
is 01508359
Wiring diagram:
EasyView MT8000
RS-485 2W (COM 1)
MOVITRAC-07
RS-485
262
Pin 1 ( )
Green
Pin 2 (D)
Red
Driver Version:
Version
Date
V1.20
Dec/30/2008
Description of Changes
263
SIEMENS S7/1200 (Ethernet)
Siemens S7/1200 series Ethernet
http://www.ad.siemens.com
HMI Setting:
1.
Parameters
Recommend
Option
PLC type
SIEMENS S7/1200 (Ethernet)
Com port
Ethernet
HMI Station No.
PLC Station No.
TCP port
102
Interval of block pack
Notes
2.
In S7-1200 program software creates PLC program and tag and then download to PLC.
Select Go offline, EB8000 will connect to PLC and get tag data.
In PLC type selectSIEMENS S7/1200 (Ethernet). Set Interval of block pack (words) to 0.
3.
Click Settings, input PLC IP address.
264
4.
Check the PLC has not any PC connected. Click Get tag info, it will show a successful
message.
5.
Create an object and click read address Setting
265
In PLC name select S7-1200 then click Tag.
Select PLC tag.
266
Support Device Type:
S7-1200 Data
type
Bool
Word
Int
DWord
Dint
Real
Array
EB8000
Data format
Memo
bit
16-bit BCD, Hex, Binary, Unsigned
16-bit BCD, Hex, Binary, Signed
32-bit BCD, Hex, Binary, Unsigned
32-bit BCD, Hex, Binary, Signed
32-bit Float
Word array for ASCII input and ASCII
display
Length=word
Wiring diagram:
Ethernet:
MT8000 Ethernet
RJ45
1
TX+
Wire color
Ethernet Hub or
Switch RJ45
1
White/Orange
RX+
RJ45 connector
2
TX-
Orange
RX-
RX+
White/Green
TX+
BD4+
Blue
BD4+
BD4-
White/Blue
BD4-
RX-
Green
TX-
BD3+
White/Brown
BD3+
BD3-
Brown
BD3-
Ethernet: Direct connect (crossover cable)
MT8000 Ethernet
RJ45
Wire color
S7-1200 Ethernet
RJ45
TX+
White/Orange
RX+
TX-
Orange
RX-
RX+
White/Green
TX+
BD4+
Blue
BD4+
BD4-
White/Blue
BD4-
RX-
Green
TX-
BD3+
White/Brown
BD3+
BD3-
Brown
BD3-
267
Notification:
On-line Simulation
OK
Multi-PLC connect
OK
Driver Version:
Version
Date
Description of Changes
V1.00
268
SIEMENS S7/200
Siemens S7/200 series PLC (CPU212/214/215/216/221/222/224/226/226XM)
http://www.ad.siemens.com
HMI Setting:
Parameters
Recommend
PLC type
SIEMENS S7/200
Com port
RS485 2w
Option
Notes
RS485 2w
Must same as the PLC setting
The
Baud rate
9600
HMIs
which
has
sticker
9600, 19200, 187.5K
MPI187.5 on the rear panel, support
187.5 baud rate.
Parity bit
Even
Even, Odd, None
Must same as the PLC setting
Data Bits
7,8
Must same as the PLC setting
Stop Bits
1, 2
Must same as the PLC setting
PLC Station No.
Turn around delay
Must same as the PLC setting
(ms)
Reserved 1
30
ACK delay time
Online Simulator
YES
Broadcast command
NO
Extend address mode
NO
PLC Setting:
Communication mode
Set station number as 2
Device address:
Bit/Word
Device Type
Format
Range
dddd(o)
0-40957
Input (I)
dddd(o)
0-40957
Output (O)
dddd(o)
0-40957
Bit Memory
VW.Bit
ddddd(o)
0-102397
V Memory bit address
VB
ddddd
0-10239
VW
ddddd
0-10239
269
Memo
V memory
VW_Odd
ddddd
0-10239
V memory
DW
VD
ddddd
0-10239
V memory double word
DW
VD_Odd
ddddd
0-10239
V memory double word
VD_String
ddddd
0-10239
String
VD_String_Odd
ddddd
0-10239
String
VW_String
ddddd
0-10239
String
VW_String_Odd
ddddd
0-10239
String
MB
ddddd
0-10239
byte memory
MW
ddddd
0-10239
Word memory
MW_Odd
ddddd
0-10239
Word memory
ddd
0-127
Timer
ddd
0-127
Counter
* Double word and Floating point value must use VD device type.
Wiring diagram:
MT8000 RS-485
9P D-SUB Female
SIEMENS S7/200
CPU Port
9P D-SUB Female
COM1
COM3
RX-
Data-
8 D-
RX+
Data+
3 D+
GND
GND
Driver Version:
Version
Date
V2.30
Aug/17/2009
Description of Changes
270
GND
SIEMENS S7/200 Ethernet
Siemens S7/200 Ethernet Series PLC(CPU212/214/215/216/221/222/224/226/226XM)
http://www.ad.siemens.com
HMI Setting:
Parameters
Recommend
PLC type
Siemens S7/200
Option
Notes
Must match the PLCs port setting.
(Ethernet)
Com port
Ethernet
Must match the PLCs port setting.
Port no.
102
Must match the PLCs port setting.
PLC station no.
0-31
Must match the PLCs port setting.
Device address:
Bit/Word
Device Type
Format
Range
Memo
dddd(o)
0-40957
Input (I)
dddd(o)
0-40957
Output (O)
dddd(o)
0-40957
Bit Memory
VW.Bit
ddddd(o)
0-102397
V Memory bit address
VW
ddddd
0-10239
V memory
VW_String
ddddd
0-10239
String
DW
VD
ddddd
0-10239
V memory double word
DW
VD_String
ddddd
0-10239
String
Double word and Floating point value must use VD device type.
Wiring diagram:
MT8000 Ethernet
Wire color
Ethernet Hub or Switch RJ45
White/Orang
Orange
White/Green
Blue
White/Blue
Green
White/Brow
Brown
1
2
3
4
5
6
7
8
RJ45
1 TX+
2 TX3 RX+
4 BD4+
5 BD46 RX7 BD3+
8 BD3-
271
RX+
RXTX+
BD4+
BD4TXBD3+
BD3-
RJ45 connector
Ethernet: Direct connect (crossover cable)
MT8000 Ethernet Wire color
Ethernet Device
RJ45
RJ45
1
2
3
TX+
TXRX+
White/Orange
Orange
White/Green
3
6
1
RX+
RXTX+
4
5
6
7
8
BD4+
BD4RXBD3+
BD3-
Blue
White/Blue
Green
White/Brown
Brown
4
5
2
7
8
BD4+
BD4TXBD3+
BD3-
Driver Version:
Version
Date
V1.20
Dec/30/2008
Description of Changes
272
SIEMENS S7/300
Siemens S7/300 series PLC
http://www.ad.siemens.com
HMI Setting:
Parameters
Recommend
PLC type
SIEMENS S7/300
Com port
RS232
Option
Notes
Must same as the PLC setting
19200, 38400,
Baud rate
187.5K
The HMIs which has sticker MPI187.5
9600~187.5K
on the rear panel, support 187.5 baud
rate.
Parity bit
Odd
Data Bits
Stop Bits
HMI Station No.
Does not apply to this protocol
PLC Station No.
Must same as the PLC setting
PLC Setting:
Communication mode
Device address:
Bit/Word
Device Type
Format
Range
dddd(o)
0-40957
Input (I)
dddd(o)
0-40957
Output (O)
dddd(o)
0-40957
Bit Memory
DB0Bit-DB99Bit
dddd(o)
0-81927
Data register bit
DB0-DB99
dddd
0-8192
Data register(must be even)
IW
dddd
0-4095
Input (I)
QW
dddd
0-4095
Output (O)
MW
dddd
0-4095
Bit Memory
DBn
dddddd
000000-998192
DBDn
fffdddd
ff:0-255, dddd:0-8192
DW
Memo
Data register(must be even)
Data register double word (must be
multiple of 4)
* Double word and Floating point value must use DBDn device type.
273
Wiring diagram:
MT8000 RS232
SIEMENS S7/300 PC
9P D-SUB Male
adapter RS232 Port
COM1
COM2
COM3
3 TX
2 RX
5 GND
4 TX
6 RX
5 GND
7 TX
8 RX
5 GND
9P D-SUB Male
2
RXD
TXD
GND
RTS
CTS
MT8000 RS232
Systeme Helmholz
9P D-SUB Male
SSW7-TS
COM1
COM2
COM3
3 TX
2 RX
5 GND
4 TX
6 RX
5 GND
7 TX
8 RX
5 GND
9P D-SUB Male
Driver Version:
Version
Date
V2.60
Jul/08/2009
V2.70
Nov/16/2009
Description of Changes
Add MD register (32-bit format)
274
RXD
TXD
GND
RTS
CTS
DTR
DSR
SIEMENS S7/300 Ethernet
Siemens S7/300 Ethernet Series PLC
http://www.ad.siemens.com
HMI Setting:
Parameters
Recommend
PLC type
Siemens S7/300
Option
Notes
Must match the PLCs port setting.
(Ethernet)
Com port
Ethernet
Must match the PLCs port setting.
Port no.
102
Must match the PLCs port setting.
PLC station no.
0-31
Must match the PLCs port setting.
Device address:
Bit/Word
Device Type
Format
Range
dddd(o)
0-40957
Input (I)
dddd(o)
0-40957
Output (O)
dddd(o)
0-40957
Bit Memory
DB0Bit-DB99Bit
dddd(o)
0-81927
Data register bit
DB0-DB99
dddd
0-8192
Data register(must be even)
IW
dddd
0-4095
Input (I)
QW
dddd
0-4095
Output (O)
MW
dddd
0-4095
Bit Memory
DBn
dddddd
000000-998192
DBDn
fffdddd
fff:0-250, dddd:0-8192
DW
Memo
Data register(must be even)
Data register double word (must be
multiple of 4)
* Double word and Floating point value must use DBDn device type.
275
Wiring diagram:
MT8000 Ethernet
Wire color
Ethernet Hub or Switch RJ45
White/Orang
Orange
White/Green
Blue
White/Blue
Green
White/Brow
Brown
1
2
3
4
5
6
7
8
RJ45
1
2
3
4
5
6
7
8
TX+
TXRX+
BD4+
BD4RXBD3+
BD3-
RX+
RXTX+
BD4+
BD4TXBD3+
BD3-
RJ45 connector
Ethernet: Direct connect (crossover cable)
MT8000 Ethernet
Wire color
Ethernet Device
RJ45
RJ45
1
2
3
TX+
TXRX+
White/Orange
Orange
White/Green
3
6
1
RX+
RXTX+
4
5
6
7
8
BD4+
BD4RXBD3+
BD3-
Blue
White/Blue
Green
White/Brown
Brown
4
5
2
7
8
BD4+
BD4TXBD3+
BD3-
Driver Version:
Version
Date
Description of Changes
V1.60
Jul/09/2009
Improved communication performance
V1.70
Nov/16/2009
Add MD register (32-bit format)
276
SIEMENS S7/300 MPI
Siemens S7/300 series PLC
http://www.ad.siemens.com
HMI Setting:
Parameters
Recommend
Option
PLC type
SIEMENS S7/300 MPI
Com port
RS485 2w
Baud rate
187.5K
Parity bit
Even
Data Bits
Stop Bits
PLC Station No.
Notes
Device address:
Bit/Word
Device Type
Format
Range
dddd(o)
0-40957
Input (I)
dddd(o)
0-40957
Output (O)
dddd(o)
0-40957
Bit Memory
DB0Bit-DB99Bit
dddd(o)
0-81927
Data register bit
DB0-DB99
dddd
0-8192
Data register(must be even)
IW
dddd
0-4095
Input (I)
QW
dddd
0-4095
Output (O)
MW
dddd
0-4095
Bit Memory
DBn
dddddd
000000-998192
DW
DBDn
ffdddd
ff:0-99, dddd:0-8192
* Double word and Floating point value must use DBDn PLC device type.
277
Memo
Data register(must be even)
Data register double word
Wiring diagram:
MT8000iV series HMI
S7-200 PPI / 9P D-SUB Male
RS485 2w 9P D-SUB Male
S7-300 MPI / 9P D-SUB Male
COM1
COM3
RX-
Data-
RX+
Data+
3 D+
GND
GND
Driver Version:
Version
Date
V1.10
Jul/09/2009
V1.20
Nov/16/2009
Description of Changes
Add MD register (32-bit format)
278
D-
GND
SIMATIC TI505
SIMATIC TI505 Series PLCs: TI520, TI525, TI530, TI535, TI545, TI555, TI560, TI565, TI575
Using the NITP protocol in a point-to-point single master, single slave format.
http://www.ad.siemens.de/simatic/controller/index_76.htm
HMI Setting:
Parameters
Recommend
Option
PLC type
SIMATIC TI505
Com port
RS232
RS232, RS485(4W)
Baud rate
19200
19200
Parity bit
Odd
Odd
Data Bits
Stop Bits
PLC Station No.
Does not apply
Notes
PLC Setting:
Communication mode
NITP protocol
Device address:
Bit/Word
Device Type
Format
Range
CR
ddddd
ddddd:1~65535
Internal Relay
ddddd
ddddd:1~65535
Discrete input coils
ddddd
ddddd:1~65535
Discrete output coils
ddddd
ddddd:1~65535
User data registers
STW
ddddd
ddddd:1~65535
Status word registers
TCP
ddddd
ddddd:1~65535
Timer/counter preset values
TCC
ddddd
ddddd:1~65535
Timer/counter current values
WX
ddddd
ddddd:1~65535
Word discrete inputs
WY
ddddd
ddddd:1~65535
Word discrete outputs
279
Memo
Wiring diagram:
RS-232:
MT8000 HMI
9P D-SUB
SIMATIC TI505
25Pin D-SUB
COM1 [RS232] COM2 [RS232] COM3 [RS232]
3
2
5
TX
RX
GND
4 TX
6 RX
5 GND
7 TX
8 RX
5 GND
3 RXD
2 TXD
7 GND
4 RTS
5 CTS
6 DSR
8 DCD
20 DTR
RS-232:
MT8000 HMI
SIMATIC TI505
9Pin D-SUB
9P D-SUB
COM1 [RS232] COM2 [RS232] COM3 [RS232]
3
2
5
TX
RX
GND
4 TX
6 RX
5 GND
7 TX
8 RX
5 GND
2 RXD
3 TXD
5 GND
7 RTS
8 CTS
1 DCD
4 DTR
6 DSR
RS485 4W:
MT8000HMI
SIMATIC TI505
9Pin D-SUB
COM1 RS-485/4w
9P D-SUB
1
RX-
DO(-)
RX+
DO(+)
TX-
DI(-)
TX+
DI(+)
GND
GND
280
Driver Version:
Version
Date
V1.10
Apr/22/2009
Description of Changes
281
TECO (TAIAN TP02)
TAIAN TP02 series
http://www.taian-technology.com
HMI Setting:
Parameters
Recommend
Option
PLC type
Taian TP02
Com port
RS485 4W/2W
RS485 4W/2W
Notes
MMI 422 port:4W; RS485
terminals:2W
Baud rate
19200
9600, 19200, 38400
Parity bit
Even
Even, Odd, None
Data Bits
7, 8
Stop Bits
1, 2
PLC Station No.
0-255
PLC Setting:
RS422 port:WS041=120,WS042=1;
RS485 terminals:WS044=120,WS045=1.
Device address:
Bit/Word
Device Type
Format
Range
Memo
ddd
1~384
Input relay
ddd
1~384
Output relay
dddd
1~2048
Auxiliary relay
ddd
ddd
dddd
1~1024
Auxiliary register
dddd
1~2048
Auxiliary register
WS
ddd
1~128
System register
dddd
WC
ddd
1-369 (must be 1 or a
multiple of plus 1)
1-369 (must be 1 or a
multiple of plus 1)
1-2033 (must be 1 or a
multiple of plus 1)
1~912
282
Input register
Output register
Auxiliary relay
register
Constant register
Wiring diagram:
TP02 Series MMI RS422 port
MT8000 RS-485 4w
9P D-SUB
1
2
3
4
RXRX+
TXTX+
TP02 series PLC
CPU RS422 port
9P D-SUB Female
8
3
7
2
TXTX+
RXRX+
TP02 Series RS485 Terminals
MT8000 RS-485 2w
TP02 series PLC
9P D-SUB
RS485 Terminals
1
2
RXRX+
T/RT/R+
Driver Version:
Version
Date
V1.10
Jan/25/2010
Description of Changes
283
TECO (TAIAN TP03)
TECO (TAIAN TP03) series PLC http://www.teco.com.tw/sa/en/
HMI Setting:
Parameters
Recommend
Option
PLC type
TAIAN TP03 Series
Com port
RS485 4w
Baud rate
19200
9600, 19200
Parity bit
None
Even, Odd, None
Data Bits
Stop Bits
PLC Station No.
1-31
Notes
Device address:
Bit/Word
Device Type
Format
Range
B
B
C
M
dddd
dddd
0 ~ 9999
0 ~ 9999
dddd
0 ~ 9999
dddd
ooo
0 ~ 9999
0 ~ 377
B
W
ooo
0 ~ 377
dddd
0 ~ 9999
dddd
0 ~ 9999
dddd
0 ~ 9999
T_Curent
dddd
0 ~ 9999
C_Curent
dddd
0 ~ 9999
T_Preset
dddd
0 ~ 9999
C_Preset
dddd
0 ~ 9999
284
Memo
Wiring diagram:
MT8000 RS-485 4w
TP03 PC/PDA port
9P D-SUB
8 Pin mini DIN
1
2
5
3
4
RXRX+
GND
TXTX+
4
7
3
1
2
TXTX+
GND
RXRX+
Driver Version:
Version
Date
V1.00
Apr/22/2009
Description of Changes
285
8 Pin mini
DIN Female
Telemecanique UniTelWay
Modicon TSX Micro&Nano&Neza series PLC
http://www.modicon.com
HMI Setting:
Parameters
Recommend
PLC type
Telemecanique
Option
Notes
UniTelWay
Com port
RS485
RS232/RS485
Baud rate
9600
9600~115200
Must same as the PLC setting
Parity bit
Odd
Even, Odd, None
Must same as the PLC setting
Data Bits
7,8
Must set as 8 to this protocol
Stop Bits
1, 2
Must same as the PLC setting
HMI Station No.
4-7
Must set by manual
PLC Station No.
0-3
Online Simulator
YES
Broadcast command
NO
Extend address mode
YES
PLC Setting:
Communication mode
UniTelWay protocol, set PLC as master
Device address:
Bit/Word
Device Type
Format
Range
ddd
0-32767
Internal relay
ddd
0-32767
Auxiliary relay
MW.B
ddd(dd)
0-999915
Data register bit
MW
ddd
0-9999
286
Memo
Data register
Wiring diagram:
TSX37-XX/TSX07-XX CPU
MT8000 RS-485
TSX series CPU port
9P D-SUB
8P mini-din Female
COM1
COM3
RX-
Data-
2 D-
RX+
Data+
1 D+
GND
GND
7 GND
Driver Version:
Version
Date
V1.20
Sep/24/2009
Description of Changes
287
8Pin miniDin Female
TECO Inverter
TECO Inverter series, 7300CV model
HMI Setting:
Parameters
Recommend
PLC type
TECO Inverter
Com port
RS232
Baud rate
38400
Parity bit
None
Data Bits
Stop Bits
HMI Station No.
PLC Station No.
Option
Notes
RS232/RS485
Device address:
Bit/Word
B
B
B
Device Type
0x
1x
3x_Bit
Format
ddddd
ddddd
ddddd(dd)
4x_Bit
ddddd(dd)
B
W
W
DW
W
0x (0x0f)
3x
4x
5x
6x
ddddd
ddddd
ddddd
ddddd
ddddd
Range
1-65535
1-65535
100-6553515
100-6553515
Memo
Output bit
Input bit (read only)
Input Register bit (read only)
1-65535
1-65535
1-65535
1-65535
1-65535
Write Multiple Coils
Input Register (read only)
Output Register
4x double word swap
4x single word write
288
Output Register bit
Wiring diagram:
MT8000 RS-232
TECO Inverter
9P D-SUB
RS232
COM1
3
TX
RX
RX
AX
GND
GND
RTS
VCC
Driver Version:
Version
Date
V1.00
Jul/27/2009
Description of Changes
289
TOSHIBA T series
Toshiba T series, S2E
http://www.tic.toshiba.com
HMI Setting:
Parameters
Recommend
PLC type
Toshiba T Serial
Com port
RS232
RS232/RS485
Baud rate
9600
9600, 19200,38400,57600,115200
Must same as the PLC setting
Parity bit
Odd
Even, Odd, None
Must same as the PLC setting
Data Bits
7,8
Must same as the PLC setting
Stop Bits
1, 2
Must same as the PLC setting
HMI Station No.
0-255
Does not apply to this protocol
PLC Station No.
0-255
In accordance with PLC setting
Online Simulator
Option
YES
Notes
In accordance with plc port
Extend address mode
YES
Broadcast command
PLC Setting:
Communication mode
Must set PLC node ID
Device address:
Bit/Word
Device Type
Format
Range
ddd(h)
0-9999f
Input Bit
ddd(h)
0-9999f
Output Bit
ddd(h)
0-9999f
Auxiliary Bit
ddd(h)
0-9999f
Special Bit
ddd
0-9999
Timer Register
ddd
0-9999
Counter Register
ddd
0-9999
Data Memory
SW
ddd
0-9999
Special Register
XW
ddd
0-9999
Input Register
YW
ddd
0-9999
Output Register
RW
ddd
0-9999
Auxiliary Register
290
Memo
Wiring diagram:
RS232
MT8000 RS232
Toshiba T1 PRG port
9P D-SUB
8P mini-D
COM1
3
2
5
COM2
TX
RX
GND
4 TX
6 RX
5 GND
RXD
TXD
GND
RTS
CTS
9P D-SUB
9P D-SUB Female
4 TX
6 RX
5 GND
COM3
7 TX
8 RX
5 GND
RS485
MT8000 COM1
Toshiba T2 LINK port
RS485
15P D-SUB Female
9P D-SUB
1
RX-
11
TXB
RX+
TXA
TX-
10
RXB
TX+
RXA
GND
SG
RTSA
CTSA
13
RTSB
12
CTSB
Driver Version:
Version
Toshiba T2 PRG port
COM2
TX
RX
GND
7 TX
8 RX
5 GND
MT8000 RS232
COM1
3
2
5
COM3
Date
Description of Changes
291
RXD
TXD
GND
RTS
CTS
V1.00
Sep/15/2009
TOSHIBA TC mini series
TOSHIBA MACHINE CO., JAPAN
Web Site: http://www.toshiba-machine.co.jp
HMI Setting:
Parameters
Recommend
Option
Notes
PLC type
Provisor TC200
Provisor TC200
Com port
RS232
RS232
Baud rate
9600
9600, 19200
Must same as the PLC setting
Parity bit
None
Even, Odd, None
Must same as the PLC setting
Data Bits
7,8
Must same as the PLC setting
Stop Bits
1, 2
Must same as the PLC setting
HMI Station No.
Does not apply to this protocol
PLC Station No.
Does not apply to this protocol
In accordance with plc port
Device address:
Bit/Word
Device Type
Format
Range
Memo
X_Bit
hhh(h)
0-fff(f)
(h) : Bit no.(0~f)
Y_Bit
hhh(h)
0-fff(f)
(h) : Bit no.(0~f)
R_Bit
hhh(h)
0-fff(f)
(h) : Bit no.(0~f)
L_Bit
hhh(h)
0-fff(f)
(h) : Bit no.(0~f)
hhh
0-fff
hhh
0-fff
hhh
0-fff
hhh
0-fff
hhh
0-fff
292
Wiring diagram:
RS232
MT8000 HMI
RS232 9P D-SUB
COM1
TC mini series
9P D-SUB
COM2
COM3
TX
TX
TX
RXD
RX
RX
RX
TXD
5 GND
GND
RTS
CTS
5 GND
5 GND
Driver Version:
Version
Date
Description of Changes
293
TOSHIBA VF-S11
Toshiba Invertor Protocol(ASCII code)
HMI Setting:
Parameters
Recommend
PLC type
Toshiba VF-S11
Com port
RS485(2 wire)
RS422, RS485
Baud rate
9600
9600, 19200
Parity bit
Even
Even, Odd, None
Data Bits
7 or 8
Stop Bits
1 or 2
HMI Station No.
PLC Station No.
Online Simulator
YES
Broadcast command
YES
Option
Notes
0-99
Extend address mode
YES
PLC Setting:
Communication mode
9600 E,8,1, Station No=0
Device address:
Bit/Word
Device Type
Format
Range
Memo
Word
Communication No.
HHH
HHH:0~ 0FFF
Parameters and data memory
Bit
Comm.No.Bit
HHH(DD)
HHH(DD):0-FFF(15)
294
Wiring diagram:
Pay Attention:
Before you connect the VF-S11, make sure you to put both switches of SW1 to the related position. (SW1:
Wiring method selector switch)
RS-485
MT8000 RS-485
TOSHIBA
9P D-SUB
VFFS1-VFPS1
COM1
RJ45
COM3
RX-
Data-
RX+
Data+
GND
GND
295
Driver Version:
Version
Date
V1.20
Aug/31/2009
Description of Changes
296
VIGOR
VIGOR M Series
http://www.vigorplc.com.tw/
HMI Setting:
Parameters
Recommend
PLC type
VIGOR
Com port
RS232
Baud rate
19200
Parity bit
Even
Data Bits
Stop Bits
HMI Station No.
PLC Station No.
Option
Notes
RS232, RS485 4wires,
PLC Setting:
Communication mode
None
Device address:
Bit/Word
Device Type
Format
Range
ooo
0~177
ooo
0~177
dddd
0~4095
ddd
0~999
ddd
0~255
ddd
0~255
TV
ddd
0~255
CV
ddd
0~255
dddd
0~4095
DL
dddd
0~4095
297
Memo
Double word
Wiring diagram:
RS-485 4wire:
MT8000
VIGOR M series
COM1 RS485 4w
6pin terminal
9P D-SUB Male
1
RX-
TX-
RX+
TX+
TX-
RX-
TX+
RX+
GND
SG
24V
RS-232:
VIGOR M series
COM Port
MT8000 RS232
9P D-SUB
COM1
3
2
5
TX
RX
GND
COM2
4 TX
6 RX
5 GND
COM3
7 TX
8 RX
5 GND
Driver Version:
Version
Date
V1.00
Dec/30/2008
Description of Changes
298
RXD
TXD
GND
YASGAWA SMC3010
YASKAWA SMC Series Servo Motor Controller
HMI Setting:
Parameters
Recommend
Device type
YASKAWA SMC 3010
Com port
RS232
Baud rate
19200
Parity bit
None
Data Bits
Stop Bits
Option
Notes
9600, 19200
Device address:
Bit/Word
Device Type
Format
Range
Memo
AF
0~1
BN
0~1
Write only
BP
0~1
Write only
BV
0~1
Write only
CB
dddd
0 ~ 9999
Write only
CM
0~1
Read only
DV
0~1
EB
0~1
OE
0~1
RS
0~1
Write only
ST
0~1
Write only
TB
0~1
Read only
V_bit
DDDdd
DDD:0~999, dd:0~31
*2
DW
AC
0~4
DW
DC
0~4
DW
BL
0~4
CD
0~2
CE
0~2
DW
DE
0~4
DW
DP
0~4
DT
0~2
Write only
299
Bit/Word
Device Type
Format
Range
Memo
EC
0~2
DW
EM
0~4
ER
0~2
FA
0~2
DW
FL
0~4
FV
0~2
DW
GR
0~4
DW
JG
0~4
DW
MM
0~4
MT
0~2
NA
0~2
OP
0~2
DW
PA
0~4
DW
PR
0~4
DW
SP
0~4
TC
0~2
TM
0~2
TW
0~2
DW
VA
0~4
DW
VD
0~4
DW
VS
0~4
DW
IL
0~4
DW
IT
0~4
DW
KD
0~4
DW
KI
0~4
DW
KP
0~4
DW
OF
0~4
DW
TL
0~4
DW
VR
0~4
DW
VT
0~4
DW
PF
0~4
DW
VF
0~4
DW
DDD
0 ~ 999
*2
DDD
0 ~ 999
*2
Write only
Read only
*1
Note:
*1 PF is the communication parameter of SMC_3010, default is 10.4, if the value is not 10.4, all
values will be displayed incorrect.
300
*2 User define integer variable V000~V999, floating point variable F000~F999.
Wiring diagram:
MT8000 RS232
9P D-SUB
SMC3010 CN6 RS232
9 pin male D-sub
COM1
COM2
COM3
TX
TX
TX
RXD
RX
RX
RX
TXD
GND
GND
GND
GND
RTS
CTS
Driver Version:
Version
Date
V1.2.0
Feb/10/2010
Description of Changes
301
YASKAWA SMC 3010 (ETHERNET)
YASKAWA SMC Series Servo Motor Controller
HMI Setting:
Parameters
Recommend
Option
Device type
YASKAWA SMC 3010
Com port
Ethernet
Notes
Port:23
Baud rate
Parity bit
Data Bits
Stop Bits
Device address:
Bit/Word
Device Type
Format
Range
Memo
AF
0~1
BN
0~1
Write only
BP
0~1
Write only
BV
0~1
Write only
CB
dddd
0 ~ 9999
Write only
CM
0~1
Read only
DV
0~1
EB
0~1
OE
0~1
RS
0~1
Write only
ST
0~1
Write only
TB
0~1
Read only
V_bit
DDDdd
DDD:0~999, dd:0~31
DW
AC
0~4
DW
DC
0~4
DW
BL
0~4
CD
0~2
CE
0~2
DW
DE
0~4
DW
DP
0~4
DT
0~2
302
*2
Write only
Bit/Word
Device Type
Format
EC
Range
Memo
0~2
DW
EM
0~4
ER
0~2
FA
0~2
DW
FL
0~4
FV
0~2
DW
GR
0~4
DW
JG
0~4
DW
MM
0~4
MT
0~2
NA
0~2
OP
0~2
DW
PA
0~4
DW
PR
0~4
DW
SP
0~4
TC
0~2
TM
0~2
TW
0~2
DW
VA
0~4
DW
VD
0~4
DW
VS
0~4
DW
IL
0~4
DW
IT
0~4
DW
KD
0~4
DW
KI
0~4
DW
KP
0~4
DW
OF
0~4
DW
TL
0~4
DW
VR
0~4
DW
VT
0~4
DW
PF
0~4
DW
VF
0~4
DW
DDD
0 ~ 999
*2
DDD
0 ~ 999
*2
Write only
Read only
*1
Note:
*1 PF is the communication parameter of SMC_3010, default is 10.4, if the value is not 10.4, all
values will be displayed incorrect.
303
*2 User define integer variable V000~V999, floating point variable F000~F999.
Wiring diagram:
Ethernet:
MT8000 Ethernet
RJ45
Wire color
Ethernet Hub or Switch
RJ45
1
2
3
TX+
TXRX+
White/Orange
Orange
White/Green
1
2
3
RX+
RXTX+
4
5
6
7
8
BD4+
BD4RXBD3+
BD3-
Blue
White/Blue
Green
White/Brown
Brown
4
5
6
7
8
BD4+
BD4TXBD3+
BD3-
Ethernet: Direct connect (crossover cable)
MT8000 Ethernet
RJ45
Wire color
SMC 3010 Ethernet
module RJ45
1
2
3
TX+
TXRX+
White/Orange
Orange
White/Green
3
6
1
RX+
RXTX+
4
5
6
7
8
BD4+
BD4RXBD3+
BD3-
Blue
White/Blue
Green
White/Brown
Brown
4
5
2
7
8
BD4+
BD4TXBD3+
BD3-
Driver Version:
Version
Date
V1.0.0
Feb/22/2010
Description of Changes
304
8
RJ45
connector
YAMAHA ERCD
HMI Setting:
Parameters
Recommend
Option
Notes
PLC type
YAMAHA ERCD
Com port
RS232
Data Bits
7 or 8
Must match the PLCs port setting.
Stop Bits
1 or 2
Must match the PLCs port setting.
Baud rate
9600
1200-19200
Must match the PLCs port setting.
Parity bit
Odd
None/Even/Odd
Must match the PLCs port setting.
PLC station
No.
Do not need to set the station No.
Device address:
Bit/Word
Device type
Range
Format
Memo
Word
ddd
0-999
Read/Write, PNT point data
Word
SWI
ddd
Write only RW0=program
number
Switches program
number to be run
Word
ORG
ddd
Write only Returns to origin
Word
Reset
ddd
Write only Reset program
Word
RUN
ddd
Write only Starts automatic
operation
Word
MOVD
ddd
Write only Directly moves to
specified position
RW1=X-axis position(mm),
RW2=speed
Word
X_ADD
ddd
Write only X command
Word
X_SUB
ddd
Write only X
305
command
Wiring diagram:
MT8000 RS232
PB
9P D-SUB
RS232
COM1
3 TX
2 RX
5 GND
3 TX
2 RX
5 GND
7 RTS
8 CTS
Driver Version:
Version
Date
V1.10
Aug/08/2009
Description of Changes
306
Yokogawa FA-M3
FA-M3 CPU SP35-5N, SP55-5N CPU port, F3LC11 Computer Link module.
http://www.yokogawa.com/itc/itc-index-en.htm
HMI Setting:
Parameters
Recommend
Option
PLC type
Yokogawa FA-M3
Com port
RS232
Baud rate
19200
9600, 19200
Parity Bit
Even
Even, Odd, None
Data Bits
Stop Bits
HMI Station No.
PLC Station No.
Notes
1-31
PLC Setting:
Communication mode
Use Personal Communication Link
Use checksum
Use End Character
Device address:
Bit/Word
Device Type
Format
Range
ddd
201-71664(discontinuous)
ddd
201-71664(discontinuous)
ddd
1-16384
ddd
1-71024(discontinuous)
ddd
1-9984
ddd
1-8192
ddd
1-32768
ddd
1-64
ddd
1-71024(discontinuous)
ddd
1-512
307
Memo
Wiring diagram:
RS-232: CPU port
MT8000 RS232
CPU port cable
9P D-SUB
KM11 RS-232
MT8000 RS232
9P D-SUB
COM1
3
2
5
TX
RX
GND
COM2
4 TX
6 RX
5 GND
COM3
7 TX
8 RX
5 GND
RXD
TXD
GND
RS-232: LC11
MT8000 RS232
LC11 Computer
9P D-SUB Female
Link module RS232
Port
COM1
3
2
5
TX
RX
GND
COM2
4 TX
6 RX
5 GND
COM3
7 TX
8 RX
5 GND
RXD
TXD
GND
RTS
CTS
How to get the WideField communication setting
If you want get the WideField communication setting, select [Tool]->[Set Environment] default is
Automatic. Using the Automatic Recognition, Wide Field software will connect the Current PLC
and get the PLC communication setting. If you have know the PLC communication configuration,
you alse can select the Fixed mode ,It will connect the PLC quickly.
308
P.S Because use Personal computer link, when you connecting to PLC it will delay about 20sec for
test communication.
How to Setting YOKOGAWA PLC Communcation
configuration.
YOKOGAWA FA-M3
CPU SP55-5N (same SP35-5N)
[File]->[New Project] to create a new project
309
click Configuration for setup communication.
310
311
Driver Version:
Version
Date
V1.10
Jan/01/2009
Description of Changes
312
Yokogawa FA-M3 (Ethernet)
FA-M3 CPU SP35-5N, SP55-5N with F3LE01-5T/F3LE11-0T Ethernet module.
http://www.yokogawa.com/itc/itc-index-en.htm
HMI Setting:
Parameters
PLC type
Com port
TCP port no.
HMI Station No.
PLC Station No.
Recommend
Yokogawa FA-M3
(Ethernet)
Ethernet
12289
0
1
Option
PLC Setting:
Communication mode
Set IP Address
Set all condition setup switch OFF.
313
Notes
Device address:
Bit/Word
Device Type
Format
Range
Memo
ddd
201-71664(discontinuous)
ddd
201-71664(discontinuous)
ddd
1-16384
ddd
1-71024(discontinuous)
ddd
1-9984
ddd
1-8192
ddd
1-32768
ddd
1-64
ddd
1-71024(discontinuous)
ddd
1-512
Wiring diagram:
Ethernet:
MT8000 Ethernet
Wire color
Ethernet Hub or Switch
RJ45
RJ45
TX+
White/Orange
RX+
TX-
Orange
RX-
RX+
White/Green
TX+
BD4+
Blue
BD4+
BD4-
White/Blue
BD4-
RX-
Green
TX-
BD3+
White/Brown
BD3+
BD3-
Brown
BD3-
Ethernet: Direct connect (crossover cable)
MT8000 Ethernet
Wire color
FA-M3 Ethernet module
RJ45
RJ45
TX+
White/Orange
RX+
TX-
Orange
RX-
RX+
White/Green
TX+
BD4+
Blue
BD4+
BD4-
White/Blue
BD4-
RX-
Green
TX-
BD3+
White/Brown
BD3+
BD3-
Brown
BD3-
314
RJ45
connector
Driver Version:
Version
Date
V1.00
Dec/30/2008
Description of Changes
315
MT6050i Com Port Connection Guide
Bottom View
MT6050i
Pin assignment of the 9 Pin, Male,
Pin assignment of the 9 Pin, Male, SUB-D, COM1 [RS-232]/ [RS-485], COM3 [RS-485] Port. Only
Com1[RS485 2W] support MPI 187.5K.
Pin#
Symbol
Com1[RS485]
4 wire
2 wire
Com1[RS232]
Com3[RS485]
Rx-
Rx-
Data-
Rx+
Rx+
Data+
Tx-
Tx-
Tx+
Tx+
GND
GND
TxD
Transmit
Data-
Data-
Data+
Data+
RxD
Receive
316
Wiring diagram:
MT6050i COM1 [RS-232]
PLC RS-232
9P D-SUB Female
Communication Com Port interface
RXD
TXD
TXD
RXD
GND
GND
MT6050i COM1 [RS-485 2w]
PLC RS-485 2w
9P D-SUB Female
Communication Com Port interface
Data-
Data-
Data+
Data+
MT6050i COM3* [RS-485 2w]
PLC RS-485 2w
9P D-SUB Female
Communication Com Port interface
Data-
Data-
Data+
Data+
*RS485 2W COM3 is only available for MT6050iv2
MT6050i COM1 [RS-485 4w]
PLC RS-485 2w
9P D-SUB Female
Communication Com Port interface
RX-
TX-
RX
TX+
TX-
RX-
TX+
RX+
317
You might also like
- S7-1500, ET 200MP Automation System ManualNo ratings yetS7-1500, ET 200MP Automation System Manual356 pages
- MELSEC-Q QD77MS Simple Motion Module User's Manual (Positioning Control) PDFNo ratings yetMELSEC-Q QD77MS Simple Motion Module User's Manual (Positioning Control) PDF1,062 pages
- FX Family - Training Manual (Positioning Control) 214562-B (08.12) PDFNo ratings yetFX Family - Training Manual (Positioning Control) 214562-B (08.12) PDF116 pages
- ControlStar Programming Software User ManualNo ratings yetControlStar Programming Software User Manual94 pages
- Rexroth Servo Drives Programming:: Page 1 of 56No ratings yetRexroth Servo Drives Programming:: Page 1 of 5656 pages
- Full FX3U FX3UC FX3G Programming Basic Applied Instructions EditionNo ratings yetFull FX3U FX3UC FX3G Programming Basic Applied Instructions Edition1,000 pages
- PDF User Manual AMD360A With Aprinter DriverNo ratings yetPDF User Manual AMD360A With Aprinter Driver7 pages
- Руководство По Подключению к ПЛК Англ ЯзыкNo ratings yetРуководство По Подключению к ПЛК Англ Язык801 pages
- Powerflex Drives With Totalforce Control Parameters Reference DataNo ratings yetPowerflex Drives With Totalforce Control Parameters Reference Data1,902 pages
- Micrologix™ Analog Input/Output: Installation InstructionsNo ratings yetMicrologix™ Analog Input/Output: Installation Instructions24 pages
- W446-E1-12 CX-Programmer V9 Operation ManualNo ratings yetW446-E1-12 CX-Programmer V9 Operation Manual536 pages
- Iv-Series-Pcsoft Um 207GB 244003 e 1122-4 PDFNo ratings yetIv-Series-Pcsoft Um 207GB 244003 e 1122-4 PDF302 pages
- Price List: Fourstar Electronic Technology Co., Ltd. Deyang ChinaNo ratings yetPrice List: Fourstar Electronic Technology Co., Ltd. Deyang China30 pages
- You Kong PLC Programming Cable CatalogueNo ratings yetYou Kong PLC Programming Cable Catalogue21 pages
- Nx-100 Operator's Manual (For General Purpose)No ratings yetNx-100 Operator's Manual (For General Purpose)410 pages
- ROBT 308 Industrial Automation: Lecture 9 - Developing Fundamental PLC Wiring Diagrams and Ladder Logic ProgramsNo ratings yetROBT 308 Industrial Automation: Lecture 9 - Developing Fundamental PLC Wiring Diagrams and Ladder Logic Programs77 pages
- A Beginner's PLC Overview, Part 1 of 4 - Introduction To PLCs PDFNo ratings yetA Beginner's PLC Overview, Part 1 of 4 - Introduction To PLCs PDF10 pages
- Rslogix Micro Software: Powerful, Easier-To-Use Programming SoftwareNo ratings yetRslogix Micro Software: Powerful, Easier-To-Use Programming Software2 pages
- PLC Programming Using SIMATIC MANAGER for Beginners: With Basic Concepts of Ladder Logic ProgrammingFrom EverandPLC Programming Using SIMATIC MANAGER for Beginners: With Basic Concepts of Ladder Logic Programming4/5 (1)
- PLC Programming & Implementation: An Introduction to PLC Programming Methods and ApplicationsFrom EverandPLC Programming & Implementation: An Introduction to PLC Programming Methods and ApplicationsNo ratings yet
