HUAWEI TECHNOLOGIES CO., LTD.

Huawei Confidential 1
The privilege of HCNA/HCNP/HCIE:
With any Huawei Career Certification, you have the privilege on http://learning.huawei.com/en to enjoy:
1Comprehensive E-Learning Courses
ContentAll Huawei Career Certification E-Learning courses
Methods to get the E-learning privilege : submit Huawei Account and email being used for Huawei Account
registration to [email protected] .
2 Training Material Download
Content: Huawei product training material and Huawei career certification training material
MethodLogon http://learning.huawei.com/en and enter HuaWei Training/Classroom Training ,then you can
download training material in the specific training introduction page.
3 Priority to participate in Huawei Online Open Class(LVC)
ContentThe Huawei career certification training covering all ICT technical domains like R&S, UC&C, Security,
Storage and so on, which are conducted by Huawei professional instructors
MethodThe plan and participate method please refer to LVC Open Courses Schedule
4Learning Tool: eNSP
eNSP (Enterprise Network Simulation Platform) is a graphical network simulation tool which is developed by
Huawei and free of charge. eNSP mainly simulates enterprise routers, switches as close to the real hardware as
it possible, which makes the lab practice available and easy without any real device.
In addition, Huawei has built up Huawei Technical Forum which allows candidates to discuss technical issues with
Huawei experts , share exam experiences with others or be acquainted with Huawei Products(
http://support.huawei.com/ecommunity/
More
Learning
Resources:
http://learning.huawei.com/en



Huawei Certification

HCNA-HNTD
ENTRY

Huawei Networking Technology and Device
Lab Guide













Huawei Technologies Co.,Ltd.

M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:
h
t
t
p
:/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
Copyright Huawei Technologies Co., Ltd. 2013. All rights reserved.
No part of this document may be reproduced or transmitted in any form or by
any means without prior written consent of Huawei Technologies Co., Ltd.
Trademarks and Permissions
and other Huawei trademarks are trademarks of Huawei Technologies
Co., Ltd. All other trademarks and trade names mentioned in this document
the property of their respective holders.
Notice
The information in this document is subject to change without notice. Every
effort has been made in the preparation of this document to ensure accuracy of
the contents, but all statements, information, and recommendations in this
document do not constitute the warranty of any kind, express or implied.



Huawei Certification
HCNA-HNTD Huawei Networking Technology and Device
Entry Lab Guide
Version 2.0

Mo
r
e

L
e
a
r
n
i
n
g

Re
s
o
u
r
c
e
s
:

h
t
t
p:
//l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/e
n


Huawei Certification System
Relying on its strong technical and professional training and certification system
and in accordance with customers of different ICT technology levels, Huawei
certification is committed to providing customers with authentic, professional
certification, and addresses the need for the development of quality engineers that
are capable of supporting Enterprise networks in the face of an ever changing ICT
industry. The Huawei certification portfolio for routing and switching (R&S) is
comprised of three levels to support and validate the growth and value of customer
skills and knowledge in routing and switching technologies.
The Huawei Certified Network Associate (HCNA) certification level validates the
skills and knowledge of IP network engineers to implement and support small to
medium-sized enterprise networks. The HCNA certification provides a rich
foundation of skills and knowledge for the establishment of such enterprise
networks, along with the capability to implement services and features within
existing enterprise networks, to effectively support true industry operations.
HCNA certification covers fundamentals skills for TCP/IP, routing, switching and
related IP network technologies, together with Huawei data communications
products, and skills for versatile routing platform (VRP) operation and
management.
The Huawei Certified Network Professional (HCNP-R&S (HCDP)) certification is
aimed at enterprise network engineers involved in design and maintenance, as well
as professionals who wish to develop an in depth knowledge of routing, switching,
network efficiency and optimization technologies. HCNP-R&S consists of three
units including Implement Enterprise Switch Network (IESN), Implement Enterprise
Routing Network (IERN), and Improving Enterprise Network Performance (IENP),
which includes advanced IPv4 routing and switching technology principles,
network security, high availability and QoS, as well as application of the covered
technologies in Huawei products.
The Huawei Certified Internet Expert (HCIE-R&S) certification is designed to imbue
engineers with a variety of IP network technologies and proficiency in maintenance,
for the diagnosis and troubleshooting of Huawei products, to equip engineers with
in-depth competency in the planning, design and optimization of large-scale IP
networks.
M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:
h
t
t
p
:/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n

Mo
r
e

Le
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:
h
t
t
p
://l
e
a
r
n
i
n
g
.h
u
a
w
e
i
.c
o
m/e
n


Reference Icons

Lab environment specification
In order to ensure that that the configuration given in this lab is supported on all
devices, it is recommended that the following device models and VRP versions
be used:

Identifier Device Model VRP version
R1 AR 2220 Version 5.120 (AR2200 V200R003C00SPC200)
R2 AR 2220 Version 5.120 (AR2200 V200R003C00SPC200)
R3 AR 2220 Version 5.120 (AR2200 V200R003C00SPC200)
S1 S5700-28C-EI-24S Version 5.70 (S5700 V100R006C00SPC800)
S2 S5700-28C-EI-24S Version 5.70 (S5700 V100R006C00SPC800)
S3 S3700-28TP-EI-AC Version 5.70 (S3700 V100R006C00SPC800)
S4 S3700-28TP-EI-AC Version 5.70 (S3700 V100R006C00SPC800)
Ethernet link Serial link
Router L3 Switch
L2 Switch Cloud
M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Content

HC Series HUAWEI TECHNOLOGIES Page1


CONTENTS
CHAPTER 1 ESTABLISHING BASIC NETWORKS WITH ENSP .................................................................. 1
LAB 1-1 BUILDING BASIC IP NETWORKS ........................................................................................................ 1
CHAPTER 2 BASIC DEVICE NAVIGATION AND CONFIGURATION ....................................................... 11
LAB 2-1 BASIC DEVICE NAVIGATION AND CONFIGURATION ............................................................................. 11
CHAPTER 3 STP AND RSTP ................................................................................................................ 22
LAB 3-1 CONFIGURING STP ...................................................................................................................... 22
LAB 3-2 CONFIGURING RSTP .................................................................................................................... 36
CHAPTER 4 ROUTING CONFIGURATION ........................................................................................... 43
LAB 4-1 CONFIGURING STATIC ROUTES AND DEFAULT ROUTES ........................................................................ 43
LAB 4-2 CONFIGURING RIPV1 AND RIPV2 ................................................................................................... 60
LAB 4-3 RIPV2 ROUTE AGGREGATION AND AUTHENTICATION ......................................................................... 74
LAB 4-4 OSPF SINGLE-AREA CONFIGURATION ............................................................................................. 90
CHAPTER 5 FTP AND DHCP ............................................................................................................. 107
LAB 5-1 CONFIGURING FTP SERVICES ....................................................................................................... 107
LAB 5-2 IMPLEMENTING DHCP ............................................................................................................... 114

Mo
r
e

Le
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:
h
t
t
p
://l
e
a
r
n
i
n
g
.h
u
a
w
e
i
.c
o
m/e
n
HCNA-HNTD Chapter 1 Establishing Basic Networks with eNSP

HC Series HUAWEI TECHNOLOGIES Page1

Chapter 1 Establishing Basic Networks with eNSP
Lab 1-1 Building Basic IP Networks
Learning Objectives
As a result of this lab section, you should achieve the following tasks:
Set up and navigate the eNSP simulator application.
Establish a simple peer-to-peer network in eNSP
Perform capture of IP packets using Wireshark within eNSP.








Mo
r
e

Le
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:
h
t
t
p
://l
e
a
r
n
i
n
g
.h
u
a
w
e
i
.c
o
m/e
n
HCNA-HNTD Chapter 1 Establishing Basic Networks with eNSP

Page2 HUAWEI TECHNOLOGIES HC Series

The fundamental network behavior can be understood through the application
of packet capture tools to the network. The use of Huaweis simulator platform
eNSP is capable of supporting both the implementation of technologies and
the capture of packets within the network to provide a comprehensive
knowledge of IP networks.
Tasks
Step 1 Initiate eNSP.
This step introduces how to start and navigate the eNSP simulator application
for rapid development of TCP/IP knowledge and familiarity with network
operation. If eNSP is not available, please inform the course instructor
After launching eNSP, the following application user interface will be presented.
The left panel houses the icons that represent the various products and
devices that are supported within eNSP, while the central panel provides lab
examples for practice scenarios.


After launching eNSP, users should select the New operator in the top left
corner of the application window to begin a new lab session.
M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 1 Establishing Basic Networks with eNSP

HC Series HUAWEI TECHNOLOGIES Page3

The user will be presented with a canvas on which to establish a network
topology for practice and analysis of network behavior. In this example a
simple peer-to-peer network using two end systems is to be established.

Step 2 Build a Topology
Select the End Devce icon in the top left panel to reveal a list of end devices
that can be applied. Select the Laptop icon and drag it to the canvas, release
the icon to place it on the canvas.



The same action should be taken to position a second laptop on the canvas for
establishing the peer-to-peer network topology.

M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 1 Establishing Basic Networks with eNSP

Page4 HUAWEI TECHNOLOGIES HC Series

The devices on the canvas represent simulated end systems that can be used
to emulate real world operations.

Step 3 Establish a physical medium
Select the connections icon from the upper left panel to reveal a list of media
that can be applied to the topology. Select the copper (Ethernet) medium from
the list. Once the icon has been clicked, the cursor will represent a connector
to show the current role of the cursor as a connector. Click on the client device
to reveal a list of port interfaces supported by the simulated device. For the
client click the option for Ethernet 0/0/1 to apply the connection.



Once this has been achieved, click on the peering device to apply the opposite
end of the medium to the end system. Again select the interface Ethernet 0/0/1
to establish the medium between the two devices and complete the
construction of a peer-to-peer topology.

M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 1 Establishing Basic Networks with eNSP

HC Series HUAWEI TECHNOLOGIES Page5

The establishment of a point-to-point network reveals a connection with two
red dots on the medium that represent the current state of the interfaces to
which the medium connects as down.

Step 4 Access the end system settings.
Select the end system and use the right click option to display a properties
menu. The settings option should be selected in order to display the current
system settings for the end system devices.




M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 1 Establishing Basic Networks with eNSP

Page6 HUAWEI TECHNOLOGIES HC Series

The settings option in the properties window reveals a set of four tabs for
establishment of basic configuration, the device command line interface,
multcast traffic generator configuration, and UDP packet generator
configuration.

Step 5 Configure the end sytem.
Ensure the Basic Config tab is selected and enter a host name in the Host
Name field window. Ensure the IPv4 configuration is currently set to static and
configure an IP address in the IP address window. It is recommended that the
address (together with the subnet mask) be configured as shown in the below
example. Once this has been configured, click the Apply button in the bottom
right corner of the window before closing with the x in the top right corner of the
CLIENT 1 window.



The same process is required for CLIENT2. It is recommended that initially the
IP address 192.168.1.2 be configured, with a subnet mask of 255.255.255.0.
The basic configuration enables peer-to-peer communication to be supported
between the two end systems.

M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 1 Establishing Basic Networks with eNSP

HC Series HUAWEI TECHNOLOGIES Page7

Step 6 Initiate the end sytem devices.
The devices can be activated using one of two methods. The first involves
using the right click option to open the properties menu and select start for the
individual icons. The alternative involves dragging the cursor over the icons (as
shown) to highlight multiple devices and using the right click settings option
start multiple devices simultaneously.



Once the devices are online and active, it is common to notice a change in the
status of the connectors through a switch in the colour of the red dot on the
medium to green, highlighting that the status of the connectors is now up.

M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 1 Establishing Basic Networks with eNSP

Page8 HUAWEI TECHNOLOGIES HC Series

Once the devices within the network topology are operational, it is possible to
begin to monitor the flow of traffic that is carried over the medium and the
interfaces via which the devices have established a physical peering.

Step 7 Implement the capture of packets on an interface.
Select the device to for whose interface is to be monitored and use the right
click option to display the settings menu. Highlight the capture data option to
reveal a list of interfaces that belong to the device and are available for
observation by the packet capture tool. Select the interface from the list that is
to be monitored.




The selection of an interface will result in the activation of the Wireshark packet
capture tool for the selected interface. If additional interfaces are to be
monitored, separate instances of the same packet capture tool will be
activated.

M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 1 Establishing Basic Networks with eNSP

HC Series HUAWEI TECHNOLOGIES Page9

Depending on the devices being monitored, the packet capture tool may or
may not begin to generate packet capture results for all traffic that passes
through the selected interface. In the case of the peer-to-peer relationship, it
will be necessary to generate some traffic.

Step 8 Generate traffic on the interface.
Open the command window on the client by either double clicking the client
icon and selecting the Command tab, or alternatively use the right click option
to enter the properties menu and select settings from which point the
Command tab can be selected.
The most basic means for generating traffic is through the ping command. This
can be achieved by entering ping <ip address> where the IP address refers to
the address of the peer.



The generation of traffic will be confirmed by the resulting output in which case
the number of packets transmitted are shown to also be received.

M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 1 Establishing Basic Networks with eNSP

Page10 HUAWEI TECHNOLOGIES HC Series

Following the generation of traffic, the resulting traffic flow shall be captured by
the packet capture tool and can be used for observation of the behavior of
protocols within the IP network along with details of the various layers as
referenced in the OSI reference model.

Step 9 Observe the captured traffic flow
An instance of the Wireshark packet capture tool should currently be active
following the action to capture data on the client interface. Maximize the active
window to observe the results of the packet capture process.



The Wireshark application contains many functions for management of the
packet capture process. One of the more common functions includes the filter
function to isolate the packet capture display to a select group of packets or
protocols. This can be achieved using the filter field below the menu bar. The
simplest filter method involves entering the protocol name (in lower case) and
pressing Enter. In the given example packets for two protocols have been
captured, entering either icmp, or arp into the filter window will result in only the
protocol entered in the filter field being displayed in the output.
The packet capture tool consists of three panels, to show the list of packets, a
breakdown of the content of each packet and finally display the equivalent data
format of the packet. The breakdown is invaluable for understanding the format
of protocol packets and displays the details for protocols as referenced at each
layer of the OSI reference model.
M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 2 Basic Device Navigation and Configuration

HC Series HUAWEI TECHNOLOGIES Page11

Chapter 2 Basic Device Navigation and Configuration
Lab 2-1 Basic Device Navigation and Configuration
Learning Objectives
As a result of this lab section, you should achieve the following tasks:
Configure device system parameters including device name, the
system time, and the system time zone.
Configure the console port idle timeout duration.
Configure the login information.
Configure the login password
Save configuration files.
Configure IP addresses for router interfaces.
Test the connectivity between two directly connected routers.
Restart a device using VRP.
Topology

Figure 2.1 Lab topology for basic VRP navigation and operation.
Scenario
A company has purchased two AR G3 routers that require commissioning
before they can be used in the enterprise network. Items to be commissioned
include setting device names, the system time, and password management.


M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 2 Basic Device Navigation and Configuration

Page12 HUAWEI TECHNOLOGIES HC Series

Tasks
Step 1 View the system information.
Run the display version command to view the software version and hardware
information for the system.
<Huawei>display version
Huawei Versatile Routing Platform Software
VRP (R) software, Version 5.120 (AR2200 V200R003C00SPC200)
Copyright (C) 2011-2013 HUAWEI TECH CO., LTD
Huawei AR2220 Router uptime is 0 week, 3 days, 21 hours, 43 minutes
BKP 0 version information:
......output omitted......

The command output includes the VRP operating system version, device
model, and startup time.
Step 2 Change the system time parameter.
The system automatically saves the time. If the time is incorrect, run the clock
timezone and clock datetime commands in the user view to change the
system time.
<Huawei>clock timezone Local add 08:00:00
<Huawei>clock datetime 12:00:00 2013-09-15

The keyword Local can be exchanged with the current regional timezone name,
and add replaced with minus where the timezone is west of UTC+0.

Run the display clock command to check that the new system time has taken
effect.
<Huawei>display clock
2013-09-15 12:00:21
Sunday
Time Zone(Default Zone Name) : UTC+00:00


M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 2 Basic Device Navigation and Configuration

HC Series HUAWEI TECHNOLOGIES Page13

Step 3 Help features & Auto-completion functions.
The question mark (?) is a wildcard, and the Tab is used as a shortcut to enter
commands.
<Huawei>display ?
Cellular Cellular interface
aaa AAA
access-user User access
accounting-scheme Accounting scheme
acl <Group> acl command group
actual Current actual
adp-ipv4 Ipv4 information
adp-mpls Adp-mpls module
alarm Alarm
antenna Current antenna that outputting radio
anti-attack Specify anti-attack configurations
ap <Group> ap command group
ap-auth-mode Display AP authentication mode
......output omit......

To display all the commands that start with a specific letter or string of letters,
enter the desired letters and the question mark (?). The system displays all the
commands that start with the letters entered. For example, if the string dis? is
entered, the system displays all the commands that start with dis.
If a space exists between the character string and the question mark (?), the
system will identify the command corresponding to the string and display the
parameters of the command. For example, if the string display ? is entered,
the system will display the parameters associated with the display command.
If multiple commands start with the same string (e.g. di ?), the system will
display an ambiguity error.
The Tab key can also be pressed to complete a command. For example, if dis
is entered followed by Tab, the system completes the display command. If
multiple commands start with dis, the appropriate command can be selected.
If there are no other commands starting with the same letters, dis or disp can
be entered to indicate display, and int or inter to indicate interface.

M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 2 Basic Device Navigation and Configuration

Page14 HUAWEI TECHNOLOGIES HC Series

Step 4 Access the system view.
Run the system-view command to access the system view to configure
interfaces and protocols.
<Huawei>system-view
Enter system view, return user view with Ctrl+Z.
[Huawei]

Step 5 Change device names.
To more easily identify devices, set device names during the device
configuration. Change device names based on the lab topology, as shown
below:
Change the name of the R1 router to R1.
[Huawei]sysname R1
[R1]

Change the name of the R3 router to R3.
[Huawei]sysname R3
[R3]

Step 6 Configure the login information.
Configure the login information to indicate the login result.
[R1]header shell information "Welcome to the Huawei certification lab."

Run the preceding command to configure the login information. To check
whether the login information has been changed, exit from the router
command line interface, and log back in to view the login information.
[R1]quit
<R1>quit

Configuration console exit, please press any key to log on
Welcome to the Huawei certification lab.
<R1>

M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 2 Basic Device Navigation and Configuration

HC Series HUAWEI TECHNOLOGIES Page15

Step 7 Configure console port parameters.
The console port by default does not have a login password. Users must
configure a password for the console port before logging in to the device.
The password can be changed in the password authentication mode to
huawei in plain text.
If there is no activity on the console port for the period of time specified by the
timeout interval, the system will automatically log out the user. When this
occurs, log in to the system again using the configured password.
The default timeout interval is set to 10 minutes. If a 10 minutes idle period is
not a reasonable amount of time for the timeout interval, change the timeout
interval to a more suitable duration, here this is set to 20 minutes.
[R1]user-interface console 0
[R1-ui-console0]authentication-mode password
[R1-ui-console0]set authentication password cipher huawei
[R1-ui-console0]idle-timeout 20 0

Run the display this command to check the configuration results.
[R1-ui-console0]display this
[V200R003C01SPC200]
#
user-interface con 0
authentication-mode password
set authentication password cipher %$%$fIn'6>NZ6*~as(#J:WU%,#72Uy8cVlN^NXkT51E
^RX;>#75,%$%$
idle-timeout 20 0

Log out of the system and log back in, using the password set. It should be
noted that this password is required to be set when the router is first initialized.
[R1-ui-console0]return
<R1>quit

Configuration console exit, please press any key to log on
Welcome to Huawei certification lab
<R1>

M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 2 Basic Device Navigation and Configuration

Page16 HUAWEI TECHNOLOGIES HC Series

Step 8 Configure interface IP addresses and descriptions.
Configure an IP address for the Gigabit Ethernet 0/0/0 interface of R1. The
subnet mask can be configured using a dotted decimal format (255.255.255.0),
or based on the subnet mask prefix length.
[R1]interface GigabitEthernet 0/0/0
[R1-GigabitEthernet0/0/0]ip address 10.0.13.1 24
[R1-GigabitEthernet0/0/0]description This interface connects to R3-G0/0/0

Run the display this command to check the configuration results at the
current interface view.
[R1-GigabitEthernet0/0/0]display this
[V200R003C00SPC200]
#
interface GigabitEthernet0/0/0
description This interface connects to R3-G0/0/0
ip address 10.0.13.1 255.255.255.0
#
Return

Run the display interface command to view the interface description.
[R1]display interface GigabitEthernet0/0/0
GigabitEthernet0/0/0 current state : UP
Line protocol current state : UP
Last line protocol up time : 2013-10-08 04:13:09
Description:This interface connects to R3-G0/0/0
Route Port,The Maximum Transmit Unit is 1500
Internet Address is 10.0.13.1/24
IP Sending Frames' Format is PKTFMT_ETHNT_2, Hardware address is 5489-9876-830b
Last physical up time : 2013-10-08 03:24:01
Last physical down time : 2013-10-08 03:25:29
Current system time: 2013-10-08 04:15:30
Port Mode: FORCE COPPER
Speed : 100, Loopback: NONE
Duplex: FULL, Negotiation: ENABLE
Mdi : AUTO
Last 300 seconds input rate 2296 bits/sec, 1 packets/sec
Last 300 seconds output rate 88 bits/sec, 0 packets/sec
Input peak rate 7392 bits/sec,Record time: 2013-10-08 04:08:41
Output peak rate 1120 bits/sec,Record time: 2013-10-08 03:27:56
M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 2 Basic Device Navigation and Configuration

HC Series HUAWEI TECHNOLOGIES Page17

Input: 3192 packets, 895019 bytes
Unicast: 0, Multicast: 1592
Broadcast: 1600, Jumbo: 0
Discard: 0, Total Error: 0
CRC: 0, Giants: 0
Jabbers: 0, Throttles: 0
Runts: 0, Symbols: 0
Ignoreds: 0, Frames: 0
Output: 181 packets, 63244 bytes
Unicast: 0, Multicast: 0
Broadcast: 181, Jumbo: 0
Discard: 0, Total Error: 0
Collisions: 0, ExcessiveCollisions: 0
Late Collisions: 0, Deferreds: 0
Input bandwidth utilization threshold : 100.00%
Output bandwidth utilization threshold: 100.00%
Input bandwidth utilization : 0.01%
Output bandwidth utilization : 0%

The command output shows that the physical status and protocol status of the
interface are UP, and the corresponding physical layer and data link layer are
functional.
Once the status has been verified, configure the IP address and description for
the interface of R3.
[R3]interface GigabitEthernet 0/0/0
[R3-GigabitEthernet0/0/0]ip address 10.0.13.3 255.255.255.0
[R3-GigabitEthernet0/0/0]description This interface connects to R1-G0/0/0
After completing the configuration, run the ping command to test the
connection between R1 and R3.
<R1>ping 10.0.13.3
PING 10.0.13.3: 56 data bytes, press CTRL_C to break
Reply from 10.0.13.3: bytes=56 Sequence=1 ttl=255 time=35 ms
Reply from 10.0.13.3: bytes=56 Sequence=2 ttl=255 time=32 ms
Reply from 10.0.13.3: bytes=56 Sequence=3 ttl=255 time=32 ms
Reply from 10.0.13.3: bytes=56 Sequence=4 ttl=255 time=32 ms
Reply from 10.0.13.3: bytes=56 Sequence=5 ttl=255 time=32 ms
--- 10.0.13.3 ping statistics ---
5 packet(s) transmitted
5 packet(s) received
0.00% packet loss
round-trip min/avg/max = 32/32/35 ms
M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 2 Basic Device Navigation and Configuration

Page18 HUAWEI TECHNOLOGIES HC Series

Step 9 View the file list stored on the current device.
Run the dir command in the user view to display the list of files in the current
directory.
<R1>dir
Directory of sd1:/

Idx Attr Size(Byte) Date Time(LMT) FileName
0 -rw- 1,738,816 Mar 14 2013 11:50:24 web.zip
1 -rw- 68,288,896 Mar 14 2013 14:17:58 ar2220-v200r003c00spc200.cc
2 -rw- 739 Mar 14 2013 16:01:17 vrpcfg.zip
1,927,476 KB total (1,856,548 KB free)

<R3>dir
Directory of sd1:/

Idx Attr Size(Byte) Date Time(LMT) FileName
0 -rw- 1,738,816 Mar 14 2013 11:50:58 web.zip
1 -rw- 68,288,896 Mar 14 2013 14:19:02 ar2220-v200r003c00spc200.cc
2 -rw- 739 Mar 14 2013 16:03:04 vrpcfg.zip

1,927,476 KB total (1,855,076 KB free)

Step 10 Manage device configuration files.
Attempt to display the saved-configuration file.
<R1>display saved-configuration
There is no correct configuration file in FLASH

Since no save-configuration file exists, save the current configuration file.
<R1>save
The current configuration will be written to the device.
Are you sure to continue? (y/n)[n]:y
It will take several minutes to save configuration file, please wait............
Configuration file had been saved successfully
Note: The configuration file will take effect after being activated


M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 2 Basic Device Navigation and Configuration

HC Series HUAWEI TECHNOLOGIES Page19

Run the following command again to view the saved configuration information:
<R1>display saved-configuration
[V200R003C00SPC200]
#
sysname R1
header shell information "Welcome to Huawei certification lab"
#
board add 0/1 1SA
board add 0/2 1SA
output omit
Run the following command to view the current configuration information:
<R1>display current-configuration
[V200R003C00SPC200]
#
sysname R1
header shell information "Welcome to Huawei certification lab"
#
board add 0/1 1SA
board add 0/2 1SA
board add 0/3 2FE
output omit
A router can store multiple configuration files. Run the following command to
view the configuration file to currently be used after the next startup:
<R3>display startup
MainBoard:
Startup system software: sd1:/ar2220-v200r003c00spc200.cc
Next startup system software: sd1:/ar2220-v200r003c00spc200.cc
Backup system software for next startup: null
Startup saved-configuration file: null
Next startup saved-configuration file: sd1:/vrpcfg.zip
Startup license file: null
Next startup license file: null
Startup patch package: null
Next startup patch package: null
Startup voice-files: null
Next startup voice-files: null

Delete configuration files from the flash memory.
<R1>reset saved-configuration
M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 2 Basic Device Navigation and Configuration

Page20 HUAWEI TECHNOLOGIES HC Series

This will delete the configuration in the flash memory.
The device configurations will be erased to reconfigure.
Are you sure? (y/n)[n]:y
Clear the configuration in the device successfully.

<R3>reset saved-configuration
This will delete the configuration in the flash memory.
The device configurations will be erased to reconfigure.
Are you sure? (y/n)[n]:y
Clear the configuration in the device successfully.

Step 11 Device restart procedure.
Use the reboot command to restart the router.
<R1>reboot
Info: The system is now comparing the configuration, please wait.
Warning: All the configuration will be saved to the next startup configuration.
Continue ? [y/n]:n
System will reboot! Continue ? [y/n]:y
Info: system is rebooting ,please wait...

<R3>reboot
Info: The system is now comparing the configuration, please wait.
Warning: All the configuration will be saved to the next startup configuration.
Continue ? [y/n]:n
System will reboot! Continue ? [y/n]:y

The system asks to save the current configuration. It is necessary to determine
whether the current configuration should be saved based on the requirements
for the lab. If unsure as to whether the the current configuration should be
saved, do not save.
Final Configuration
[R1]display current-configuration
[V200R003C00SPC200]
#
sysname R1
header shell information "Welcome to Huawei certification lab"
#
interface GigabitEthernet0/0/0
M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 2 Basic Device Navigation and Configuration

HC Series HUAWEI TECHNOLOGIES Page21

description This interface connects to R3-G0/0/0
ip address 10.0.13.1 255.255.255.0
#
user-interface con 0
authentication-mode password
set authentication password
cipher %$%$4D0K*-E"t/I7[{HD~kgW,%dgkQQ!&|;XTDq9SFQJ.27M%dj,%$%$
idle-timeout 20 0
#
return

[R3]dispay current-configuration
[V200R003C00SPC200]
#
sysname R3
#
interface GigabitEthernet0/0/0
description This interface connect to R1-G0/0/0
ip address 10.0.13.3 255.255.255.0
#
user-interface con 0
authentication-mode password
set authentication password
cipher %$%$M8\HO3:72:ERQ8JLoHU8,%t+lE:$9=a7"8%yMoARB]$B%t.,%$%$
user-interface vty 0 4
#
return
M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 3 STP and RSTP

Page22 HUAWEI TECHNOLOGIES HC Series

Chapter 3 STP and RSTP
Lab 3-1 Configuring STP
Learning Objectives
As a result of this lab section, you should achieve the following tasks:
Enable and disable STP.
Change the STP mode that is used by a switch.
Change the bridge priority to control root bridge election.
Change the port priority to control election of the root port and
designated port.
Change the port cost to control election of the root port and designated
port.
Configure an edge port.
Topology

Figure 3.1 STP topology
Scenario
Assume that you are a network administrator of a company. The company
network consists of two layers: core layer and access layer. The network uses
a design that supports network redundancy. STP will be used to prevent loops.
The STP network should include setting the bridge priority to control STP root
bridge election, and configuration of features to speed up STP route
convergence.
M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 3 STP and RSTP

HC Series HUAWEI TECHNOLOGIES Page23

Tasks
Step 1 Configure STP and verify the STP configuration.
Irrelevant interfaces must be disabled to ensure test result accuracy.
Shut down port interfaces Ethernet 0/0/1 on S3, Ethernet 0/0/13 and Ethernet
0/0/23 on S3, as well as Ethernet 0/0/14 and Ethernet 0/0/24 on S4 before
starting STP configuration. Ensure that the devices start without any
configuration files. If STP is disabled, run the stp enable command to enable
STP.
<Quidway>system-view
[Quidway]sysname R3
[R3]interface Ethernet 0/0/1
[R3-Ethernet0/0/1]shutdown
[R3-Ethernet0/0/1]quit
[R3]interface Ethernet 0/0/13
[R3-Ethernet0/0/13]shutdown
[R3-Ethernet0/0/13]quit
[R3]interface Ethernet 0/0/23
[R3-Ethernet0/0/23]shutdown

<Quidway>system-view
[Quidway]sysname S4
[S4]inter Ethernet 0/0/14
[S4-Ethernet0/0/14]shutdown
[S4-Ethernet0/0/14]quit
[S4]interface Ethernet 0/0/24
[S4-Ethernet0/0/24]shutdown

In the lab,S1 and S2 are connected through two links, and STP is used.
Enable STP on S1 and S2 and set S1 as the root.
<Quidway>system-view
Enter system view, return user view with Ctrl+Z.
[Quidway]sysname S1
[S1]stp mode stp
[S1]stp root primary




M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 3 STP and RSTP

Page24 HUAWEI TECHNOLOGIES HC Series

<Quidway>system-view
Enter system view, return user view with Ctrl+Z.
[Quidway]sysname S2
[S2]stp mode stp
[S2]stp root secondary

Run the display stp brief command to view brief information about STP.
<S1>display stp brief
MSTID Port Role STP State Protection
0 GigabitEthernet0/0/9 DESI FORWARDING NONE
0 GigabitEthernet0/0/10 DESI FORWARDING NONE

<S2>display stp brief
MSTID Port Role STP State Protection
0 GigabitEthernet0/0/9 ROOT FORWARDING NONE
0 GigabitEthernet0/0/10 ALTE DISCARDING NONE

Run the display stp interface command to view the STP status of a port.


<S1>display stp interface GigabitEthernet 0/0/10
----[CIST][Port10(GigabitEthernet0/0/10)][FORWARDING]----
Port Protocol :Enabled
Port Role :Designated Port
Port Priority :128
Port Cost(Dot1T ) :Config=auto / Active=20000
Designated Bridge/Port :0.4c1f-cc45-aace / 128.10
Port Edged :Config=default / Active=disabled
Point-to-point :Config=auto / Active=true
Transit Limit :147 packets/hello-time
Protection Type :None
Port STP Mode :STP
Port Protocol Type :Config=auto / Active=dot1s
BPDU Encapsulation :Config=stp / Active=stp
PortTimes :Hello 2s MaxAge 20s FwDly 15s RemHop 20
TC or TCN send :17
TC or TCN received :33
BPDU Sent :221
TCN: 0, Config: 221, RST: 0, MST: 0
BPDU Received :68
TCN: 0, Config: 68, RST: 0, MST: 0
M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 3 STP and RSTP

HC Series HUAWEI TECHNOLOGIES Page25

<S2>display stp interface GigabitEthernet 0/0/10
----[CIST][Port10(GigabitEthernet0/0/10)][DISCARDING]----
Port Protocol :Enabled
Port Role :Alternate Port
Port Priority :128
Port Cost(Dot1T ) :Config=auto / Active=20000
Designated Bridge/Port :0.4c1f-cc45-aace / 128.10
Port Edged :Config=default / Active=disabled
Point-to-point :Config=auto / Active=true
Transit Limit :147 packets/hello-time
Protection Type :None
Port STP Mode :STP
Port Protocol Type :Config=auto / Active=dot1s
BPDU Encapsulation :Config=stp / Active=stp
PortTimes :Hello 2s MaxAge 20s FwDly 15s RemHop 0
TC or TCN send :17
TC or TCN received :17
BPDU Sent :35
TCN: 0, Config: 35, RST: 0, MST: 0
BPDU Received :158
TCN: 0, Config: 158, RST: 0, MST: 0

Step 2 Control root bridge election.
Run the display stp command to view information about the root bridge.
<S1>display stp
-------[CIST Global Info][Mode STP]-------
CIST Bridge :0 .4c1f-cc45-aace
Bridge Times :Hello 2s MaxAge 20s FwDly 15s MaxHop 20
CIST Root/ERPC :0 .4c1f-cc45-aace / 0
CIST RegRoot/IRPC :0 .4c1f-cc45-aace / 0
CIST RootPortId :0.0
BPDU-Protection :Disabled
CIST Root Type :Primary root
TC or TCN received :108
TC count per hello :0
STP Converge Mode :Normal
Share region-configuration :Enabled
Time since last TC :0 days 0h:9m:23s
output omit


M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 3 STP and RSTP

Page26 HUAWEI TECHNOLOGIES HC Series

<S2>display stp
-------[CIST Global Info][Mode STP]-------
CIST Bridge :4096 .4c1f-cc45-aacc
Bridge Times :Hello 2s MaxAge 20s FwDly 15s MaxHop 20
CIST Root/ERPC :0 .4c1f-cc45-aace / 20000
CIST RegRoot/IRPC :4096 .4c1f-cc45-aacc / 0
CIST RootPortId :128.9
BPDU-Protection :Disabled
CIST Root Type :Secondary root
TC or TCN received :55
TC count per hello :0
STP Converge Mode :Normal
Share region-configuration :Enabled
Time since last TC :0 days 0h:9m:30s
output omit
Configure S1 as the root bridge and S2 as the backup root bridge using priority
values. The device with the same value for the CIST Bridge and CIST
Root/ERPC is the root bridge. A smaller bridge priority value indicates a higher
bridge priority. Change the priorities of S1 and S2 to 8192 and 4096
respectively so that S2 becomes the root bridge.
[S1]undo stp root
[S1]stp priority 8192

[S2]undo stp root
[S2]stp priority 4096

Run the display stp command to view information about the new root bridge.
<S1>display stp
-------[CIST Global Info][Mode STP]-------
CIST Bridge :8192 .4c1f-cc45-aace
Bridge Times :Hello 2s MaxAge 20s FwDly 15s 0
CIST Root/ERPC :4096 .4c1f-cc45-aacc / 20000
CIST RegRoot/IRPC :8192 .4c1f-cc45-aace / 0
CIST RootPortId :128.9
BPDU-Protection :Disabled
TC or TCN received :143
TC count per hello :0
STP Converge Mode :Normal
Share region-configuration :Enabled
Time since last TC :0 days 0h:0m:27s
output omit
M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 3 STP and RSTP

HC Series HUAWEI TECHNOLOGIES Page27

<S2>display stp
-------[CIST Global Info][Mode STP]-------
CIST Bridge :4096 .4c1f-cc45-aacc
Bridge Times :Hello 2s MaxAge 20s FwDly 15s MaxHop 20
CIST Root/ERPC :4096 .4c1f-cc45-aacc / 0
CIST RegRoot/IRPC :4096 .4c1f-cc45-aacc / 0
CIST RootPortId :0.0
BPDU-Protection :Disabled
TC or TCN received :55
TC count per hello :0
STP Converge Mode :Normal
Share region-configuration :Enabled
Time since last TC :0 days 0h:14m:7s
output omit
The highlighted lines in the preceding information indicate that S2 has become
the new root bridge.
Shut down interfaces Gigabit Ethernet 0/0/9 and Gigabit Ethernet 0/0/10 on S2
to isolate S2.
[S2]interface GigabitEthernet 0/0/9
[S2-GigabitEthernet0/0/9]shutdown
[S2-GigabitEthernet0/0/9]quit
[S2]interface GigabitEthernet 0/0/10
[S2-GigabitEthernet0/0/10]shutdown

[S1]display stp
-------[CIST Global Info][Mode STP]-------
CIST Bridge :8192 .4c1f-cc45-aace
Bridge Times :Hello 2s MaxAge 20s FwDly 15s MaxHop 20
CIST Root/ERPC :8192 .4c1f-cc45-aace / 0
CIST RegRoot/IRPC :8192 .4c1f-cc45-aace / 0
CIST RootPortId :0.0
BPDU-Protection :Disabled
TC or TCN received :146
TC count per hello :0
STP Converge Mode :Normal
Share region-configuration :Enabled
Time since last TC :0 days 0h:0m:11s
output omit

The highlighted lines in the preceding information indicate that S1 becomes
the root bridge when S2 is faulty.
M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 3 STP and RSTP

Page28 HUAWEI TECHNOLOGIES HC Series

Re-enable the interfaces that have been disabled on S2.
[S2]interface GigabitEthernet 0/0/9
[S2-GigabitEthernet0/0/9]undo shutdown
[S2-GigabitEthernet0/0/9]quit
[S2]interface GigabitEthernet 0/0/10
[S2-GigabitEthernet0/0/10]undo shutdown

<S1>display stp
-------[CIST Global Info][Mode STP]-------
CIST Bridge :8192 .4c1f-cc45-aace
Bridge Times :Hello 2s MaxAge 20s FwDly 15s 0
CIST Root/ERPC :4096 .4c1f-cc45-aacc / 20000
CIST RegRoot/IRPC :8192 .4c1f-cc45-aace / 0
CIST RootPortId :128.9
BPDU-Protection :Disabled
TC or TCN received :143
TC count per hello :0
STP Converge Mode :Normal
Share region-configuration :Enabled
Time since last TC :0 days 0h:0m:27s
output omitted

<S2>display stp
-------[CIST Global Info][Mode STP]-------
CIST Bridge :4096 .4c1f-cc45-aacc
Bridge Times :Hello 2s MaxAge 20s FwDly 15s MaxHop 20
CIST Root/ERPC :4096 .4c1f-cc45-aacc / 0
CIST RegRoot/IRPC :4096 .4c1f-cc45-aacc / 0
CIST RootPortId :0.0
BPDU-Protection :Disabled
TC or TCN received :55
TC count per hello :0
STP Converge Mode :Normal
Share region-configuration :Enabled
Time since last TC :0 days 0h:14m:7s
output omitted

The highlighted lines in the preceding information indicate that S2 has been
restored and has become the root bridge once again.
M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 3 STP and RSTP

HC Series HUAWEI TECHNOLOGIES Page29

Step 3 Control root port election.
Run the display stp brief command on S1 to view the roles of the interfaces.
<S1>display stp brief
MSTID Port Role STP State Protection
0 GigabitEthernet0/0/9 ROOT FORWARDING NONE
0 GigabitEthernet0/0/10 ALTE DISCARDING NONE

The preceding information shows that G0/0/9 is the root port and G0/0/10 is
the alternate port. You can change port priorities so that port interface G0/0/10
will become the root port and G0/0/9 will become the alternate port.
Change priorities of G0/0/9 and G0/0/10 on S2.
The default port priority is 128. A larger port priority value indicates a lower
priority. The priorities of G0/0/9 and G0/0/10 on S2 are set to 32 and 16;
therefore, G0/0/10 on S1 becomes the root port.
[S2]interface GigabitEthernet 0/0/9
[S2-GigabitEthernet0/0/9]stp port priority 32
[S2-GigabitEthernet0/0/9]quit
[S2]interface GigabitEthernet 0/0/10
[S2-GigabitEthernet0/0/10]stp port priority 16

Note that the port priorities are changed on S2, not S1.
<S2>display stp interface GigabitEthernet 0/0/9
----[CIST][Port9(GigabitEthernet0/0/9)][FORWARDING]----
Port Protocol :Enabled
Port Role :Designated Port
Port Priority :32
Port Cost(Dot1T ) :Config=auto / Active=20000
Designated Bridge/Port :4096.4c1f-cc45-aacc / 32.9
Port Edged :Config=default / Active=disabled
Point-to-point :Config=auto / Active=true
Transit Limit :147 packets/hello-time
Protection Type :None
Port STP Mode :STP
Port Protocol Type :Config=auto / Active=dot1s
BPDU Encapsulation :Config=stp / Active=stp
PortTimes :Hello 2s MaxAge 20s FwDly 15s RemHop 20
TC or TCN send :22
TC or TCN received :1
M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 3 STP and RSTP

Page30 HUAWEI TECHNOLOGIES HC Series

BPDU Sent :164
TCN: 0, Config: 164, RST: 0, MST: 0
BPDU Received :2
TCN: 1, Config: 1, RST: 0, MST: 0

<S2>display stp interface GigabitEthernet 0/0/10
----[CIST][Port10(GigabitEthernet0/0/10)][FORWARDING]----
Port Protocol :Enabled
Port Role :Designated Port
Port Priority :16
Port Cost(Dot1T ) :Config=auto / Active=20000
Designated Bridge/Port :4096.4c1f-cc45-aacc / 16.10
Port Edged :Config=default / Active=disabled
Point-to-point :Config=auto / Active=true
Transit Limit :147 packets/hello-time
Protection Type :None
Port STP Mode :STP
Port Protocol Type :Config=auto / Active=dot1s
BPDU Encapsulation :Config=stp / Active=stp
PortTimes :Hello 2s MaxAge 20s FwDly 15s RemHop 20
TC or TCN send :35
TC or TCN received :1
BPDU Sent :183
TCN: 0, Config: 183, RST: 0, MST: 0
BPDU Received :2
TCN: 1, Config: 1, RST: 0, MST: 0

Run the display stp brief command on S1 to view the role of the interfaces.
<S1>display stp brief
MSTID Port Role STP State Protection
0 GigabitEthernet0/0/9 ALTE DISCARDING NONE
0 GigabitEthernet0/0/10 ROOT FORWARDING NONE

The highlighted lines in the preceding information indicate that G0/0/10 on S1
has become the root port and G0/0/9 has become the alternate port.
Shut down G0/0/10 on S1 and view the port roles.
[S1]interface GigabitEthernet 0/0/10
[S1-GigabitEthernet0/0/10]shutdown
<S1>display stp brief
MSTID Port Role STP State Protection
0 GigabitEthernet0/0/9 ROOT FORWARDING NONE
M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 3 STP and RSTP

HC Series HUAWEI TECHNOLOGIES Page31


The highlighted line in the preceding information indicates that G0/0/9 has
become the root port. Resume the default priorities of G0/0/9 and G0/0/10 on
S2 and re-enable the shutdown interfaces on S1.
[S2]interface GigabitEthernet 0/0/9
[S2-GigabitEthernet0/0/9]undo stp port priority
[S2-GigabitEthernet0/0/9]quit
[S2]interface GigabitEthernet 0/0/10
[S2-GigabitEthernet0/0/10]undo stp port priority

[S1]interface GigabitEthernet 0/0/10
[S1-GigabitEthernet0/0/10]undo shutdown

Run the display stp brief and display stp interface command on S1 to view
the roles of interfaces.
<S1>display stp brief
MSTID Port Role STP State Protection
0 GigabitEthernet0/0/9 ROOT FORWARDING NONE
0 GigabitEthernet0/0/10 ALTE DISCARDING NONE

[S1]display stp interface GigabitEthernet 0/0/9
----[CIST][Port9(GigabitEthernet0/0/9)][FORWARDING]----
Port Protocol :Enabled
Port Role :Root Port
Port Priority :128
Port Cost(Dot1T ) :Config=auto / Active=20000
Designated Bridge/Port :4096.4c1f-cc45-aacc / 128.9
Port Edged :Config=default / Active=disabled
Point-to-point :Config=auto / Active=true
Transit Limit :147 packets/hello-time
Protection Type :None
Port STP Mode :STP
Port Protocol Type :Config=auto / Active=dot1s
BPDU Encapsulation :Config=stp / Active=stp
PortTimes :Hello 2s MaxAge 20s FwDly 15s RemHop 0
TC or TCN send :4
TC or TCN received :90
BPDU Sent :5
TCN: 4, Config: 1, RST: 0, MST: 0
BPDU Received :622
TCN: 0, Config: 622, RST: 0, MST: 0
M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 3 STP and RSTP

Page32 HUAWEI TECHNOLOGIES HC Series


[S1]display stp interface GigabitEthernet 0/0/10
----[CIST][Port10(GigabitEthernet0/0/10)][DISCARDING]----
Port Protocol :Enabled
Port Role :Alternate Port
Port Priority :128
Port Cost(Dot1T ) :Config=auto / Active=20000
Designated Bridge/Port :4096.4c1f-cc45-aacc / 128.10
Port Edged :Config=default / Active=disabled
Point-to-point :Config=auto / Active=true
Transit Limit :147 packets/hello-time
Protection Type :None
Port STP Mode :STP
Port Protocol Type :Config=auto / Active=dot1s
BPDU Encapsulation :Config=stp / Active=stp
PortTimes :Hello 2s MaxAge 20s FwDly 15s RemHop 0
TC or TCN send :3
TC or TCN received :90
BPDU Sent :4
TCN: 3, Config: 1, RST: 0, MST: 0
BPDU Received :637
TCN: 0, Config: 637, RST: 0, MST: 0

The greyed line in the preceding information indicates that G0/0/9 and G0/0/10
cost is 20000 by default.
Change the cost of G0/0/9 to 200000 on S1.
[S1]interface GigabitEthernet 0/0/9
[S1-GigabitEthernet0/0/9]stp cost 200000

Run the display stp brief and display stp interface command on S1 to view
the roles of interfaces.
<S1>display stp interface GigabitEthernet 0/0/9
----[CIST][Port9(GigabitEthernet0/0/9)][DISCARDING]----
Port Protocol :Enabled
Port Role :Alternate Port
Port Priority :128
Port Cost(Dot1T ) :Config=200000 / Active=200000
Designated Bridge/Port :4096.4c1f-cc45-aacc / 128.9
Port Edged :Config=default / Active=disabled
Point-to-point :Config=auto / Active=true
Transit Limit :147 packets/hello-time
M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 3 STP and RSTP

HC Series HUAWEI TECHNOLOGIES Page33

Protection Type :None
Port STP Mode :STP
Port Protocol Type :Config=auto / Active=dot1s
BPDU Encapsulation :Config=stp / Active=stp
PortTimes :Hello 2s MaxAge 20s FwDly 15s RemHop 0
TC or TCN send :4
TC or TCN received :108
BPDU Sent :5
TCN: 4, Config: 1, RST: 0, MST: 0
BPDU Received :818
TCN: 0, Config: 818, RST: 0, MST: 0

<S1>display stp brief
MSTID Port Role STP State Protection
0 GigabitEthernet0/0/9 ALTE DISCARDING NONE
0 GigabitEthernet0/0/10 ROOT FORWARDING NONE

The highlighted lines in the preceding information indicates that G0/0/10 has
become the root port.
Final Configuration
<S1>display current-configuration
#
!Software Version V100R006C00SPC800
sysname S1
#
stp mode stp
stp instance 0 priority 8192
#
interface GigabitEthernet0/0/9
stp instance 0 cost 200000
#
interface GigabitEthernet0/0/10
#
user-interface con 0
user-interface vty 0 4
#
return

<S2>display current-configuration
#
M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 3 STP and RSTP

Page34 HUAWEI TECHNOLOGIES HC Series

!Software Version V100R006C00SPC800
sysname S2
#
stp mode stp
stp instance 0 priority 4096
#
interface GigabitEthernet0/0/9
#
interface GigabitEthernet0/0/10
#
user-interface con 0
user-interface vty 0 4
#
return

<S3>display current-configuration
#
!Software Version V100R006C00SPC800
sysname S3
#
interface Ethernet0/0/1
shutdown
#
interface Ethernet0/0/13
shutdown
#
interface Ethernet0/0/23
shutdown
#
user-interface con 0
user-interface vty 0 4
#
return


<S4>display current-configuration
#
!Software Version V100R006C00SPC800
sysname S4
#
interface Ethernet0/0/14
shutdown
#
M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 3 STP and RSTP

HC Series HUAWEI TECHNOLOGIES Page35

interface Ethernet0/0/24
shutdown
#
user-interface con 0
user-interface vty 0 4
#
return


Mo
r
e

Le
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:
h
t
t
p
://l
e
a
r
n
i
n
g
.h
u
a
w
e
i
.c
o
m/e
n
HCNA-HNTD Chapter 3 STP and RSTP

Page36 HUAWEI TECHNOLOGIES HC Series

Lab 3-2 Configuring RSTP
Learning Objectives
As a result of this lab section, you should achieve the following tasks:
Enable and disable RSTP .
Configuration of an edge port.
Configuration of RSTP BPDU protection.
Configuration of RSTP loop protection
Topology

Figure 3.2 RSTP topology
Scenario
Assume that you are a network administrator of a company. The company
network consists of two layers: core layer and access layer. The network uses
a redundancy design. RSTP will be used to prevent loops. You can configure
features to speed up RSTP route convergence at the edge network and
configure RSTP protection function.
Tasks
Step 1 Preparing the environment
If you are starting this section with a non-configured device, begin here and
then move to step 3. For those continuing from previous labs, begin at step 2.
Irrelevant interfaces must be disabled to ensure test result accuracy.
Shut down port interfaces Ethernet 0/0/1 on S3, Ethernet 0/0/13 and Ethernet
M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 3 STP and RSTP

HC Series HUAWEI TECHNOLOGIES Page37

0/0/23 on S3, as well as Ethernet 0/0/14 and Ethernet 0/0/24 on S4 before
starting STP configuration. Ensure that the devices start without any
configuration files. If STP is disabled, run the stp enable command to enable
STP.
<Quidway>system-view
Enter system view, return user view with Ctrl+Z.
[Quidway]sysname S1

<Quidway>system-view
Enter system view, return user view with Ctrl+Z.
[Quidway]sysname S2

<Quidway>system-view
[Quidway]sysname R3
[R3]interface Ethernet 0/0/1
[R3-Ethernet0/0/1]shutdown
[R3-Ethernet0/0/1]quit
[R3]interface Ethernet 0/0/13
[R3-Ethernet0/0/13]shutdown
[R3-Ethernet0/0/13]quit
[R3]interface Ethernet 0/0/23
[R3-Ethernet0/0/23]shutdown

<Quidway>system-view
[Quidway]sysname S4
[S4]inter Ethernet 0/0/14
[S4-Ethernet0/0/14]shutdown
[S4-Ethernet0/0/14]quit
[S4]interface Ethernet 0/0/24
[S4-Ethernet0/0/24]shutdown


Step 2 Clean up the previous configuration
Remove the configured STP priority from S1 and S2, and assigned cost on S1.
[S1]undo stp priority
[S1]inter GigabitEthernet 0/0/9
[S1-GigabitEthernet0/0/9]undo stp cost

[S2]undo stp priority
M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 3 STP and RSTP

Page38 HUAWEI TECHNOLOGIES HC Series

Step 3 Configure RSTP and verify the RSTP configuration.
Configure S1 and S2 to use RSTP as the spanning tree protocol.
[S1]stp mode rstp

[S2]stp mode rstp

Run the display stp command to view brief information about RSTP.
[S1]display stp
-------[CIST Global Info][Mode RSTP]-------
CIST Bridge :32768.4c1f-cc45-aace
Bridge Times :Hello 2s MaxAge 20s FwDly 15s MaxHop 20
CIST Root/ERPC :32768.4c1f-cc45-aacc / 20000
CIST RegRoot/IRPC :32768.4c1f-cc45-aace / 0
CIST RootPortId :128.9
BPDU-Protection :Disabled
TC or TCN received :28
TC count per hello :0
STP Converge Mode :Normal
Share region-configuration :Enabled
Time since last TC :0 days 0h:11m:1s
output omitted

[S2]display stp
-------[CIST Global Info][Mode RSTP]-------
CIST Bridge :32768.4c1f-cc45-aacc
Bridge Times :Hello 2s MaxAge 20s FwDly 15s MaxHop 20
CIST Root/ERPC :32768.4c1f-cc45-aacc / 0
CIST RegRoot/IRPC :32768.4c1f-cc45-aacc / 0
CIST RootPortId :0.0
BPDU-Protection :Disabled
TC or TCN received :14
TC count per hello :0
STP Converge Mode :Normal
Share region-configuration :Enabled
Time since last TC :0 days 0h:12m:23s
output omitted

M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 3 STP and RSTP

HC Series HUAWEI TECHNOLOGIES Page39

Step 4 Configure an edge port.
Configure ports connected to the user terminals as edge ports. An edge port
can transition to the forwarding state without participating in the RSTP
calculation. In this example, interface Gigabit Ethernet 0/0/4 on S1 and S2
connect to a router and can be configured as edge ports.
[S1]interface GigabitEthernet 0/0/4
[S1-GigabitEthernet0/0/4]stp edged-port enable

[S2]interface GigabitEthernet 0/0/4
[S2-GigabitEthernet0/0/4]stp edged-port enable

Step 5 Configure BPDU protection.
Edge ports are directly connected to user terminal and will not receive BPDUs.
Attackers may send pseudo BPDUs to attack the switching device. If the edge
ports receive the BPDUs, the switching device configures the edge ports as
non-edge ports and triggers a new spanning tree calculation. Network flapping
then occurs. BPDU protection can be used to protect switching devices against
malicious attacks.
Configure BPDU protection on both S1 and S2.
[S1]stp bpdu-protection

[S2]stp bpdu-protection

Run the display stp brief command to view the port protection.
<S1>display stp brief
MSTID Port Role STP State Protection
0 GigabitEthernet0/0/4 DESI FORWARDING BPDU
0 GigabitEthernet0/0/9 ROOT FORWARDING NONE
0 GigabitEthernet0/0/10 ALTE DISCARDING NONE

<S2>display stp brief
MSTID Port Role STP State Protection
0 GigabitEthernet0/0/4 DESI FORWARDING BPDU
0 GigabitEthernet0/0/9 DESI FORWARDING NONE
0 GigabitEthernet0/0/10 DESI FORWARDING NONE

After the configuration is complete, interface Gigabit Ethernet 0/0/4 on S1 and
M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 3 STP and RSTP

Page40 HUAWEI TECHNOLOGIES HC Series

S2 shows as supporting BPDU protection.

Step 6 Configure Loop protection
On a network running RSTP, a switching device maintains the root port status
and status of alternate ports by receiving BPDUs from an upstream switching
device. If the switching device cannot receive BPDUs from the upstream
device because of link congestion or unidirectional-link failure, the switching
device re-selects a root port. The original root port becomes a designated port
and the original discarding ports change to the Forwarding state. This
switching may cause network loops, which can be mitigated by configuring
loop protection.
Configure loop protection on both the root port and the alternate port.
[S1]display stp brief
MSTID Port Role STP State Protection
0 GigabitEthernet0/0/4 DESI FORWARDING BPDU
0 GigabitEthernet0/0/9 ROOT FORWARDING NONE
0 GigabitEthernet0/0/10 ALTE DISCARDING NONE

G0/0/9 and G0/0/10 on S1 are now the root port and alternate port.Configure
loop protection on these two ports.
[S1]interface GigabitEthernet 0/0/9
[S1-GigabitEthernet0/0/9]stp loop-protection
[S1-GigabitEthernet0/0/9]quit
[S1]interface GigabitEthernet 0/0/10
[S1-GigabitEthernet0/0/10]stp loop-protection

Run the display stp brief command to view the port protection.
<S1>display stp brief
MSTID Port Role STP State Protection
0 GigabitEthernet0/0/4 DESI FORWARDING BPDU
0 GigabitEthernet0/0/9 ROOT FORWARDING LOOP
0 GigabitEthernet0/0/10 ALTE DISCARDING LOOP

Since S2 is root, all the ports are designated ports and therefore do not need to
configure loop protection. After completing the configuration, you may wish to
set S1 as the root, and configure loop protection on the root port and alternate
port of S2 using the same process as with S1.
M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 3 STP and RSTP

HC Series HUAWEI TECHNOLOGIES Page41

Final Configuration
<S1>display current-configuration
#
!Software Version V100R006C00SPC800
sysname S1
#
stp mode rstp
stp bpdu-protection
#
interface GigabitEthernet0/0/4
stp edged-port enable
#
interface GigabitEthernet0/0/9
stp loop-protection
#
interface GigabitEthernet0/0/10
stp loop-protection
#
user-interface con 0
user-interface vty 0 4
#
return



<S2>display current-configuration
#
!Software Version V100R006C00SPC800
sysname S2
#
stp mode rstp
stp bpdu-protection
#
interface GigabitEthernet0/0/4
stp edged-port enable
#
user-interface con 0
user-interface vty 0 4
#
return

M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 3 STP and RSTP

Page42 HUAWEI TECHNOLOGIES HC Series


<S3>display current-configuration
#
!Software Version V100R006C00SPC800
sysname S3
#
interface Ethernet0/0/1
shutdown
#
interface Ethernet0/0/13
shutdown
#
interface Ethernet0/0/23
shutdown
#
user-interface con 0
user-interface vty 0 4
#
return


<S4>dis current-configuration
#
!Software Version V100R006C00SPC800
sysname S4
#
interface Ethernet0/0/14
shutdown
#
interface Ethernet0/0/24
shutdown
#
user-interface con 0
user-interface vty 0 4
#
return

M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 4 Routing Configuration

HC Series HUAWEI TECHNOLOGIES Page43

Chapter 4 Routing Configuration
Lab 4-1 Configuring Static Routes and Default Routes
Learning Objectives
As a result of this lab section, you should achieve the following tasks:
Configuration of a static route using an interface and an IP address as
the next hop.
Verification of static route operation
Implementation of the interconnection between a local and external
network using a default route.
Configuration of a backup static route on a router
Topology

Figure 4.1 Lab topology for static and default routes

M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:
h
t
t
p
:/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 4 Routing Configuration

Page44 HUAWEI TECHNOLOGIES HC Series

Scenario
Assume that you are a network administrator of a company that contains a
single administrative domain and within the administrative domain, multiple
networks have been defined, for which currently no method of routing exists.
Since the network scale is small, with only a few networks, static routes and
default routes are to be used to implement interwork communication. The
network addressing is to be applied as shown in Figure 4.1.
If a password is requested, and unless otherwise stated, please use the
password: huawei
Tasks
Step 1 Perform basic system and IP address configuration.
Configure the device names and IP addresses for R1, R2, and R3.
<Huawei>system-view
Enter system view, return user view with Ctrl+Z.
[Huawei]sysname R1
[R1]interface GigabitEthernet 0/0/0
[R1-GigabitEthernet0/0/0]ip address 10.0.13.1 24
[R1-GigabitEthernet0/0/0]quit
[R1]interface GigabitEthernet 0/0/1
[R1-GigabitEthernet0/0/1]ip address 10.0.12.1 24
[R1-GigabitEthernet0/0/1]quit
[R1]interface LoopBack 0
[R1-LoopBack0]ip address 10.0.1.1 24


Run the display current-configuration command to check the configuration.
<R1>display ip interface brief
Interface IP Address/Mask Physical Protocol
......output omitted......
GigabitEthernet0/0/0 10.0.13.1/24 up up
GigabitEthernet0/0/1 10.0.12.1/24 up up
GigabitEthernet0/0/2 unassigned up down
LoopBack0 10.0.1.1/24 up up(s)
......output omitted......
M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 4 Routing Configuration

HC Series HUAWEI TECHNOLOGIES Page45


<Huawei>system-view
Enter system view, return user view with Ctrl+Z.
[Huawei]sysname R2
[R2]interface GigabitEthernet 0/0/1
[R2-GigabitEthernet0/0/1]ip address 10.0.12.2 24
[R2-GigabitEthernet0/0/1]quit
[R2]interface GigabitEthernet0/0/2
[R2-GigabitEthernet0/0/2]ip add 10.0.23.2 24
[R2-GigabitEthernet0/0/2]quit
[R2]interface LoopBack0
[R2-LoopBack0]ip address 10.0.2.2 24


<R2>display ip interface brief
Interface IP Address/Mask Physical Protocol
......output omitted......
GigabitEthernet0/0/0 unassigned up down
GigabitEthernet0/0/1 10.0.12.2/24 up up
GigabitEthernet0/0/2 10.0.23.2/24 up up
LoopBack0 10.0.2.2/24 up up(s)
......output omitted......

<Huawei>system-view
Enter system view, return user view with Ctrl+Z.
[Huawei]sysname R3
[R3]interface GigabitEthernet 0/0/0
[R3-GigabitEthernet0/0/0]ip address 10.0.13.3 24
[R3-GigabitEthernet0/0/0]quit
[R3]interface GigabitEthernet0/0/2
[R3-GigabitEthernet0/0/2]ip address 10.0.23.3 24
[R3-GigabitEthernet0/0/2]quit
[R3]interface LoopBack 0
[R3-LoopBack0]ip address 10.0.3.3 24

<R3>display ip interface brief
Interface IP Address/Mask Physical Protocol
......output omitted......
GigabitEthernet0/0/0 10.0.13.3/24 up up
GigabitEthernet0/0/1 unassigned up down
GigabitEthernet0/0/2 10.0.23.3/24 up up
LoopBack0 10.0.3.3/24 up up(s)
......output omitted......
M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 4 Routing Configuration

Page46 HUAWEI TECHNOLOGIES HC Series


Use the ping command to test network connectivity from R1.
<R1>ping 10.0.12.2
PING 10.0.12.2: 56 data bytes, press CTRL_C to break
Reply from 10.0.12.2: bytes=56 Sequence=1 ttl=255 time=30 ms
Reply from 10.0.12.2: bytes=56 Sequence=2 ttl=255 time=30 ms
Reply from 10.0.12.2: bytes=56 Sequence=3 ttl=255 time=30 ms
Reply from 10.0.12.2: bytes=56 Sequence=4 ttl=255 time=30 ms
Reply from 10.0.12.2: bytes=56 Sequence=5 ttl=255 time=30 ms

--- 10.0.12.2 ping statistics ---
5 packet(s) transmitted
5 packet(s) received
0.00% packet loss
round-trip min/avg/max = 30/30/30 ms

<R1>ping 10.0.13.3
PING 10.0.13.2: 56 data bytes, press CTRL_C to break
Reply from 10.0.13.3: bytes=56 Sequence=1 ttl=255 time=6 ms
Reply from 10.0.13.3: bytes=56 Sequence=2 ttl=255 time=2 ms
Reply from 10.0.13.3: bytes=56 Sequence=3 ttl=255 time=2 ms
Reply from 10.0.13.3: bytes=56 Sequence=4 ttl=255 time=2 ms
Reply from 10.0.13.3: bytes=56 Sequence=5 ttl=255 time=2 ms

--- 10.0.13.3 ping statistics ---
5 packet(s) transmitted
5 packet(s) received
0.00% packet loss
round-trip min/avg/max = 2/2/6 ms

Use the ping command to test network connectivity from R2

<R2>ping 10.0.23.3
PING 10.0.23.3: 56 data bytes, press CTRL_C to break
Reply from 10.0.23.3: bytes=56 Sequence=1 ttl=255 time=31 ms
Reply from 10.0.23.3: bytes=56 Sequence=2 ttl=255 time=31 ms
Reply from 10.0.23.3: bytes=56 Sequence=3 ttl=255 time=41 ms
Reply from 10.0.23.3: bytes=56 Sequence=4 ttl=255 time=31 ms
Reply from 10.0.23.3: bytes=56 Sequence=5 ttl=255 time=41 ms

--- 10.0.23.3 ping statistics ---
5 packet(s) transmitted
M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 4 Routing Configuration

HC Series HUAWEI TECHNOLOGIES Page47

5 packet(s) received
0.00% packet loss
round-trip min/avg/max = 31/35/41 ms

Step 2 Test connectivity from R2 to 10.0.13.0/24 and 10.0.3.0/24.
<R2>ping 10.0.13.3
PING 10.0.13.3: 56 data bytes, press CTRL_C to break
Request time out
Request time out
Request time out
Request time out
Request time out

--- 10.0.13.3 ping statistics ---
5 packet(s) transmitted
0 packet(s) received
100.00% packet loss

<R2>ping 10.0.3.3
PING 10.0.3.3: 56 data bytes, press CTRL_C to break
Request time out
Request time out
Request time out
Request time out
Request time out

--- 10.0.3.3 ping statistics ---
5 packet(s) transmitted
0 packet(s) received
100.00% packet loss

If R2 wishes to communicate with the network segment 10.0.3.0, a route
destined for this network segment must be configured on R2, and routes
destined for the R2 interface must be configured on R3.
The preceding test result shows that R2 cannot communicate with 10.0.3.3
and 10.0.13.3.


M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 4 Routing Configuration

Page48 HUAWEI TECHNOLOGIES HC Series

Run the display ip routing-table command to view the routing table of R2.
The routing table does not contain the routes of the two networks.
<R2>display ip routing-table
Route Flags: R - relay, D - download to fib
----------------------------------------------------------------------------
Routing Tables: Public
Destinations : 13 Routes : 13
Destination/Mask Proto Pre Cost Flags NextHop Interface
10.0.2.0/24 Direct 0 0 D 10.0.2.2 LoopBack0
10.0.2.2/32 Direct 0 0 D 127.0.0.1 LoopBack0
10.0.2.255/32 Direct 0 0 D 127.0.0.1 LoopBack0
10.0.12.0/24 Direct 0 0 D 10.0.12.2 GigabitEthernet0/0/1
10.0.12.2/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/1
10.0.12.255/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/1
10.0.23.0/24 Direct 0 0 D 10.0.23.2 GigabitEthernet0/0/2
10.0.23.2/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/2
10.0.23.255/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/2
127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0
127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
127.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
255.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0

Step 3 Configure static routes on R2.
Configure a static route for destination networks 10.0.13.0/24 and 10.0.3.0/24,
with the next hop set as the IP address 10.0.23.3 of R3, a preference value of
60 is the default and need not be set.
[R2]ip route-static 10.0.13.0 24 10.0.23.3
[R2]ip route-static 10.0.3.0 24 10.0.23.3

Note: In the ip route-static command, 24 indicates the subnet mask length,
which can also be expressed using the decimal format 255.255.255.0.
<R2>display ip routing-table
Route Flags: R - relay, D - download to fib
Destination/Mask Proto Pre Cost Flags NextHop Interface
10.0.3.0/24 Static 60 0 RD 10.0.23.3 GigabitEthernet0/0/2
10.0.12.0/24 Direct 0 0 D 10.0.12.2 GigabitEthernet0/0/1
10.0.12.2/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/1
10.0.12.255/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/1
M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 4 Routing Configuration

HC Series HUAWEI TECHNOLOGIES Page49

10.0.13.0/24 Static 60 0 RD 10.0.23.3 GigabitEthernet0/0/2
10.0.23.0/24 Direct 0 0 D 10.0.23.2 GigabitEthernet0/0/2
10.0.23.2/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/2

Step 4 Configure backup static routes.
The data exchanged between R2 and 10.0.13.3 and 10.0.3.3 is transmitted
through the link between R2 and R3. R2 fails to communicate with 10.0.13.3
and 10.0.3.3 if the link between R2 and R3 is faulty.
According to the topology, R2 can communicate with R3 through R1 if the link
between R2 and R3 fails. A backup static route can be configured to enable
this redundancy. Backup static routes do not take effect in normal cases. If the
link between R2 and R3 fails, backup static routes are used to transfer data.
Amend th preferences for on the backup static routes to ensure that the routes
are used only when the primary link fails. In this example, the preference of the
backup static route is set to 80.
[R1]ip route-static 10.0.3.0 24 10.0.13.3

[R2]ip route-static 10.0.13.0 255.255.255.0 10.0.12.1 preference 80
[R2]ip route-static 10.0.3.0 24 10.0.12.1 preference 80

[R3]ip route-static 10.0.12.0 24 10.0.13.1

Step 5 Test the static routes.
View the current static route configuration in the routing table of R2.
<R2>display ip routing-table
Route Flags: R - relay, D - download to fib
----------------------------------------------------------------------------
Routing Tables: Public
Destinations : 15 Routes : 15
Destination/Mask Proto Pre Cost Flags NextHop Interface
10.0.2.0/24 Direct 0 0 D 10.0.2.2 LoopBack0
10.0.2.2/32 Direct 0 0 D 127.0.0.1 LoopBack0
10.0.2.255/32 Direct 0 0 D 127.0.0.1 LoopBack0
10.0.3.0/24 Static 60 0 RD 10.0.23.3 GigabitEthernet0/0/2
10.0.12.0/24 Direct 0 0 D 10.0.12.2 GigabitEthernet0/0/1
10.0.12.2/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/1
10.0.12.255/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/1
M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 4 Routing Configuration

Page50 HUAWEI TECHNOLOGIES HC Series

10.0.13.0/24 Static 60 0 RD 10.0.23.3 GigabitEthernet0/0/2
10.0.23.0/24 Direct 0 0 D 10.0.23.2 GigabitEthernet0/0/2
10.0.23.2/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/2
10.0.23.255/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/2
127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0
127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
127.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
255.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0

The routing table contains two static routes that were configured in step 3. The
value of the Protocol field is Static, indicating a static route. The value of the
Preference field is 60, indicating the default preference is used for the route.
Test network connectivity to ensure the route between R2 and R3 exists.
<R2>ping 10.0.13.3
PING 10.0.13.3: 56 data bytes, press CTRL_C to break
Reply from 10.0.13.3: bytes=56 Sequence=1 ttl=255 time=34 ms
Reply from 10.0.13.3: bytes=56 Sequence=2 ttl=255 time=34 ms
Reply from 10.0.13.3: bytes=56 Sequence=3 ttl=255 time=34 ms
Reply from 10.0.13.3: bytes=56 Sequence=4 ttl=255 time=34 ms
Reply from 10.0.13.3: bytes=56 Sequence=5 ttl=255 time=34 ms

--- 10.0.13.3 ping statistics ---
5 packet(s) transmitted
5 packet(s) received
0.00% packet loss
round-trip min/avg/max = 34/34/34 ms

<R2>ping 10.0.3.3
PING 10.0.3.3: 56 data bytes, press CTRL_C to break
Reply from 10.0.3.3: bytes=56 Sequence=1 ttl=255 time=41 ms
Reply from 10.0.3.3: bytes=56 Sequence=2 ttl=255 time=41 ms
Reply from 10.0.3.3: bytes=56 Sequence=3 ttl=255 time=41 ms
Reply from 10.0.3.3: bytes=56 Sequence=4 ttl=255 time=41 ms
Reply from 10.0.3.3: bytes=56 Sequence=5 ttl=255 time=41 ms

--- 10.0.3.3 ping statistics ---
5 packet(s) transmitted
5 packet(s) received
0.00% packet loss
round-trip min/avg/max = 41/41/41 ms

M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 4 Routing Configuration

HC Series HUAWEI TECHNOLOGIES Page51

The command output shows that the route is functioning normally. The tracert
command can also be run to view the path over which the data is transferred.
<R2>tracert 10.0.13.3
traceroute to 10.0.13.3(10.0.13.3), max hops: 30 ,packet length: 40,
press CTRL_C to break
1 10.0.23.3 40 ms 31 ms 30 ms

<R2>tracert 10.0.3.3
traceroute to 10.0.3.3(10.0.3.3), max hops: 30 ,packet length: 40,
press CTRL_C to break
1 10.0.23.3 40 ms 30 ms 30 ms

The command output verifies that R2 directly sends data to R3.
Step 6 Test the backup static routes.
Disable the path to 10.0.23.3 via GigabitEthernet0/0/2 on R2 and observe the
changes in the IP routing tables.
[R2]intface GigabitEthernet0/0/2
[R2-GigabitEthernet0/0/2]shutdown
[R2-GigabitEthernet0/0/2]quit

Compare the routing tables with the previous routing tables before Gigabit
Ethernet 0/0/2 was disabled.
<R2>display ip routing-table
Route Flags: R - relay, D - download to fib
----------------------------------------------------------------------------
Routing Tables: Public
Destinations : 12 Routes : 12

Destination/Mask Proto Pre Cost Flags NextHop Interface

10.0.2.0/24 Direct 0 0 D 10.0.2.2 LoopBack0
10.0.2.2/32 Direct 0 0 D 127.0.0.1 LoopBack0
10.0.2.255/32 Direct 0 0 D 127.0.0.1 LoopBack0
10.0.3.0/24 Static 80 0 D 10.0.12.2 GigabitEthernet0/0/1
10.0.12.0/24 Direct 0 0 D 10.0.12.2 GigabitEthernet0/0/1
10.0.12.2/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/1
10.0.12.255/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/1
10.0.13.0/24 Static 80 0 D 10.0.12.2 GigabitEthernet0/0/1
M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 4 Routing Configuration

Page52 HUAWEI TECHNOLOGIES HC Series

127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0
127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
127.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
255.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0

The next hops and preferences of the two routes as shown in the preceding
routing table for R2 have changed.
Test connectivity between R2 and the destination addresses 10.0.13.3 and
10.0.3.3 on R2.
<R2>ping 10.0.3.3
PING 10.0.3.3: 56 data bytes, press CTRL_C to break
Reply from 10.0.3.3: bytes=56 Sequence=1 ttl=255 time=3 ms
Reply from 10.0.3.3: bytes=56 Sequence=2 ttl=255 time=2 ms
Reply from 10.0.3.3: bytes=56 Sequence=3 ttl=255 time=2 ms
Reply from 10.0.3.3: bytes=56 Sequence=4 ttl=255 time=2 ms
Reply from 10.0.3.3: bytes=56 Sequence=5 ttl=255 time=2 ms

--- 10.0.3.3 ping statistics ---
5 packet(s) transmitted
5 packet(s) received
0.00% packet loss
round-trip min/avg/max = 2/2/3 ms

<R2>ping 10.0.13.3
PING 10.0.13.3: 56 data bytes, press CTRL_C to break
Reply from 10.0.13.3: bytes=56 Sequence=1 ttl=255 time=3 ms
Reply from 10.0.13.3: bytes=56 Sequence=2 ttl=255 time=2 ms
Reply from 10.0.13.3: bytes=56 Sequence=3 ttl=255 time=2 ms
Reply from 10.0.13.3: bytes=56 Sequence=4 ttl=255 time=2 ms
Reply from 10.0.13.3: bytes=56 Sequence=5 ttl=255 time=2 ms

--- 10.0.13.3 ping statistics ---
5 packet(s) transmitted
5 packet(s) received
0.00% packet loss
round-trip min/avg/max = 2/2/3 ms

The network is not disconnected when the link between R2 and R3 is shut
down.

M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 4 Routing Configuration

HC Series HUAWEI TECHNOLOGIES Page53

The tracert command can also be run to view through over which path the
data is being forwarded.
<R2>tracert 10.0.13.3
traceroute to 10.0.13.3(10.0.13.3), max hops: 30 ,packet length: 40,press CTRL_C
to break
1 10.0.12.1 40 ms 21 ms 21 ms
2 10.0.13.3 30 ms 21 ms 21 ms

<R2>tracert 10.0.3.3
traceroute to 10.0.3.3(10.0.3.3), max hops: 30 ,packet length: 40,press CTRL_C
to break
1 10.0.12.1 40 ms 21 ms 21 ms
2 10.0.13.3 30 ms 21 ms 21 ms

The command output shows that the data sent by R2 reaches R3 via the
10.0.12.0 and 10.0.13.0 networks connected to R1.
Step 7 Using default routes to implement network connectivity.
Enable the interface that was disabled in step 6 on R2.
[R2]intface GigabitEthernet 0/0/2
[R2-GigabitEthernet0/0/2]undo shutdown

Verify connectivity to the network 10.0.23.0 from R1.
[R1]ping 10.0.23.3
PING 10.0.23.3: 56 data bytes, press CTRL_C to break
Request time out
Request time out
Request time out
Request time out
Request time out

--- 10.0.23.3 ping statistics ---
5 packet(s) transmitted
0 packet(s) received
100.00% packet loss

R3 cannot be reached because the route destined for 10.0.23.3 is not
configured on R1.

M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 4 Routing Configuration

Page54 HUAWEI TECHNOLOGIES HC Series

<R1>display ip routing-table
Route Flags: R - relay, D - download to fib
----------------------------------------------------------------------------
Routing Tables: Public
Destinations : 14 Routes : 14
Destination/Mask Proto Pre Cost Flags NextHop Interface

10.0.1.0/24 Direct 0 0 D 10.0.1.1 LoopBack0
10.0.1.1/32 Direct 0 0 D 127.0.0.1 LoopBack0
10.0.1.255/32 Direct 0 0 D 127.0.0.1 LoopBack0
10.0.3.0/24 Static 60 0 RD 10.0.13.3 GigabitEthernet0/0/0
10.0.12.0/24 Direct 0 0 D 10.0.12.1 GigabitEthernet0/0/1
10.0.12.1/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/1
10.0.12.255/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/1
10.0.13.0/24 Direct 0 0 D 10.0.13.1 GigabitEthernet0/0/0
10.0.13.1/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/0
10.0.13.255/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/0
127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0
127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
127.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
255.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0

A default route can be configured on R1 to implement network connectivity via
a next hop of 10.0.13.3.
[R1]ip route-static 0.0.0.0 0.0.0.0 10.0.13.3

After the configuration is complete, test connectivity between R1 and
10.0.23.3.
<R1>ping 10.0.23.3
PING 10.0.23.3: 56 data bytes, press CTRL_C to break
Reply from 10.0.23.3: bytes=56 Sequence=1 ttl=255 time=3 ms
Reply from 10.0.23.3: bytes=56 Sequence=2 ttl=255 time=2 ms
Reply from 10.0.23.3: bytes=56 Sequence=3 ttl=255 time=2 ms
Reply from 10.0.23.3: bytes=56 Sequence=4 ttl=255 time=2 ms
Reply from 10.0.23.3: bytes=56 Sequence=5 ttl=255 time=2 ms

--- 10.0.23.3 ping statistics ---
5 packet(s) transmitted
5 packet(s) received
0.00% packet loss
round-trip min/avg/max = 2/2/3 ms
M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 4 Routing Configuration

HC Series HUAWEI TECHNOLOGIES Page55

The default route forwards traffic destined for 10.0.23.3 to the next hop of
10.0.13.3 on R3. R3 is directly connected to the 10.0.23.0 network.
Step 8 Configure a backup default route.
If the link between R1 and R3 fails, a backup default route can be used to
communicate with 10.0.23.3 and 10.0.3.3 via the 10.0.12.0 network.
However, R1 is not directly connected to these networks and therefore a
backup route (in both directions) must be configured to provide a forwarding
path.
[R1]ip route-static 0.0.0.0 0.0.0.0 10.0.12.2 preference 80

[R3]ip route-static 10.0.12.0 24 10.0.23.2 preference 80

Step 9 Test the backup default route.
View the routes of R1 when the link between R1 and R3 works properly.
<R1>display ip routing-table
Route Flags: R - relay, D - download to fib
----------------------------------------------------------------------------
Routing Tables: Public
Destinations : 15 Routes : 15
Destination/Mask Proto Pre Cost Flags NextHop Interface
0.0.0.0/0 Static 60 0 RD 10.0.13.3 GigabitEthernet0/0/0
10.0.1.0/24 Direct 0 0 D 10.0.1.1 LoopBack0
10.0.1.1/32 Direct 0 0 D 127.0.0.1 LoopBack0
10.0.1.255/32 Direct 0 0 D 127.0.0.1 LoopBack0
10.0.3.0/24 Static 60 0 RD 10.0.13.3 GigabitEthernet0/0/0
10.0.12.0/24 Direct 0 0 D 10.0.12.1 GigabitEthernet0/0/1
10.0.12.1/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/1
10.0.12.255/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/1
10.0.13.0/24 Direct 0 0 D 10.0.13.1 GigabitEthernet0/0/0
10.0.13.1/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/0
10.0.13.255/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/0
127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0
127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
127.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
255.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0

M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 4 Routing Configuration

Page56 HUAWEI TECHNOLOGIES HC Series

Disable Gigabit Ethernet 0/0/0 on R1 and disable interface Gigabit Ethernet
0/0/0 on R3 to simulate a link failure, and then view the routes of R1. Compare
the current routes with the routes before Gigabit Ethernet 0/0/0 was disabled.
[R1]interface GigabitEthernet0/0/0
[R1-GigabitEthernet0/0/0]shutdown
[R1-GigabitEthernet0/0/0]quit

[R3]interface GigabitEthernet0/0/0
[R3-GigabitEthernet0/0/0]shutdown
[R3-GigabitEthernet0/0/0]quit

<R1>display ip routing-table
Route Flags: R - relay, D - download to fib
-------------------------------------------------------------------------
Routing Tables: Public
Destinations : 11 Routes : 11
Destination/Mask Proto Pre Cost Flags NextHop Interface
0.0.0.0/0 Static 80 0 RD 10.0.12.2 GigabitEthernet0/0/1
10.0.1.0/24 Direct 0 0 D 10.0.1.1 LoopBack0
10.0.1.1/32 Direct 0 0 D 127.0.0.1 LoopBack0
10.0.1.255/32 Direct 0 0 D 127.0.0.1 LoopBack0
10.0.12.0/24 Direct 0 0 D 10.0.12.1 GigabitEthernet0/0/1
10.0.12.1/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/1
10.0.12.255/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/1
127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0
127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
127.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
255.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0

According to the preceding routing table, the value of 80 in the Preference
column indicates that the backup default route 0.0.0.0 is actively forwarding
traffic to the next hop of 10.0.23.3.
Test network connectivity on R1.
<R1>ping 10.0.23.3
PING 10.0.23.3: 56 data bytes, press CTRL_C to break
Reply from 10.0.23.3: bytes=56 Sequence=1 ttl=254 time=76 ms
Reply from 10.0.23.3: bytes=56 Sequence=2 ttl=254 time=250 ms
Reply from 10.0.23.3: bytes=56 Sequence=3 ttl=254 time=76 ms
Reply from 10.0.23.3: bytes=56 Sequence=4 ttl=254 time=76 ms
Reply from 10.0.23.3: bytes=56 Sequence=5 ttl=254 time=76 ms
M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 4 Routing Configuration

HC Series HUAWEI TECHNOLOGIES Page57

--- 10.0.23.3 ping statistics ---
5 packet(s) transmitted
5 packet(s) received
0.00% packet loss
round-trip min/avg/max = 76/110/250 ms
<R1>tracert 10.0.23.3
traceroute to 10.0.23.3(10.0.23.2), max hops: 30 ,packet length: 40,press CTRL_C
to break
1 10.0.12.2 30 ms 26 ms 26 ms
2 10.0.23.3 60 ms 53 ms 56 ms

The IP packets are reaching R3 (10.0.23.3) via the next hop 10.0.12.2 of R2.
Final Configuration
<R1>dis current-configuration
[V200R003C00SPC200]
#
sysname R1
#
interface GigabitEthernet0/0/0
shutdown
ip address 10.0.13.1 255.255.255.0
#
interface GigabitEthernet0/0/1
ip address 10.0.12.1 255.255.255.0
#
interface LoopBack0
ip address 10.0.1.1 255.255.255.0
#
ip route-static 0.0.0.0 0.0.0.0 10.0.13.3
ip route-static 0.0.0.0 0.0.0.0 10.0.12.2 preference 80
ip route-static 10.0.3.0 255.255.255.0 10.0.13.3
ip route-static 10.0.12.0 255.255.255.0 10.0.23.2 preference 80
#
user-interface con 0
authentication-mode password
set authentication password cipher %$%$+L'YR&IZt'4,)>-*#lH",}%K-oJ_M9+'lOU~bD
(\WTqB}%N,%$%$
user-interface vty 0 4
#
return
M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 4 Routing Configuration

Page58 HUAWEI TECHNOLOGIES HC Series

<R2>display current-configuration
[V200R003C00SPC200]
#
sysname R2
interface GigabitEthernet0/0/1
ip address 10.0.12.2 255.255.255.0
#
interface GigabitEthernet0/0/2
ip address 10.0.23.2 255.255.255.0
#
interface LoopBack0
ip address 10.0.2.2 255.255.255.0
#
ip route-static 10.0.3.0 255.255.255.0 10.0.23.3
ip route-static 10.0.3.0 255.255.255.0 10.0.12.1 preference 80
ip route-static 10.0.13.0 255.255.255.0 10.0.23.3
ip route-static 10.0.13.0 255.255.255.0 10.0.12.1 preference 80
#
user-interface con 0
authentication-mode password
set authentication password cipher %$%$1=cd%b%/O%Id-8X:by1N,+s}'4wD6TvO<I|/pd#
#44C@+s#,%$%$
user-interface vty 0 4
#
return

<R3>display current-configuration
[V200R003C00SPC200]
#
sysname R3
#
interface GigabitEthernet0/0/0
shutdown
ip address 10.0.13.3 255.255.255.0
#
interface GigabitEthernet0/0/2
ip address 10.0.23.3 255.255.255.0
#
interface LoopBack0
ip address 10.0.3.3 255.255.255.0
#
ip route-static 10.0.12.0 255.255.255.0 10.0.13.1
ip route-static 10.0.12.0 255.255.255.0 10.0.23.2 preference 80
M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 4 Routing Configuration

HC Series HUAWEI TECHNOLOGIES Page59

#
user-interface con 0
authentication-mode password
set authentication password cipher %$%$ksXDMg7Ry6yUU:63:DQ),#/sQg"@*S\U#.s.bHW
xQ,y%#/v,%$%$
user-interface vty 0 4
#
return









M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 4 Routing Configuration

Page60 HUAWEI TECHNOLOGIES HC Series

Lab 4-2 Configuring RIPv1 and RIPv2
Learning Objectives
As a result of this lab section, you should achieve the following tasks:
Establish routing loop prevention mechanisms for RIP
Configuration of RIPv1.
Enable RIP for a specified network and interface.
Use of the display and debugging commands to view RIP operation.
Procedure for testing connectivity of the RIP network.
Configuration of RIPv2.
Topology

Figure 4.2 Lab topology for RIPv1 and RIPv2
M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 4 Routing Configuration

HC Series HUAWEI TECHNOLOGIES Page61

Scenario
Assume that you are a network administrator in charge of managing a small
administrative domain consisting of three routers and five networks. Due to the
limited requirement, RIP is to be used to support routing. RIPv1 is initially
configured, but you realize that RIPv2 has many advantages. After some
consideration, you transition the domain to support RIPv2.
Tasks
Step 1 Preparing the environment.
If you are starting this section with a non-configured device begin here and
then move to step 3. For those continuing from previous labs, begin at step 2.
<Huawei>system-view
Enter system view, return user view with Ctrl+Z.
[Huawei]sysname R1
[R1]interface GigabitEthernet 0/0/0
[R1-GigabitEthernet0/0/0]ip address 10.0.13.1 24
[R1-GigabitEthernet0/0/0]quit
[R1]interface LoopBack 0
[R1-LoopBack0]ip address 10.0.1.1 24
[R1-LoopBack0]quit

<Huawei>system-view
Enter system view, return user view with Ctrl+Z.
[Huawei]sysname R2
[R2]interface GigabitEthernet 0/0/1
[R2-GigabitEthernet0/0/1]ip address 10.0.12.2 24
[R2-GigabitEthernet0/0/1]quit
[R2]interface LoopBack 0
[R2-LoopBack0]ip address 10.0.2.2 24

<Huawei>system-view
Enter system view, return user view with Ctrl+Z.
[Huawei]sysname R3
[R3]interface LoopBack 0
[R3-LoopBack0]ip address 10.0.3.3 24

M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 4 Routing Configuration

Page62 HUAWEI TECHNOLOGIES HC Series

Step 2 Clean up the previous configuration
Clean up previous static route configuration and disable all unsed interfaces

[R1]interface GigabitEthernet0/0/1
[R1-GigabitEthernet0/0/1]shutdown
[R1-GigabitEthernet0/0/1]quit
[R1]interface GigabitEthernet0/0/0
[R1-GigabitEthernet0/0/0]undo shutdown
[R1-GigabitEthernet0/0/0]quit
[R1]undo ip route-static 0.0.0.0 0.0.0.0
[R1]undo ip route-static 10.0.3.0 255.255.255.0
[R1]undo ip route-static 10.0.12.0 255.255.255.0


[R2]interface GigabitEthernet 0/0/2
[R2-GigabitEthernet0/0/2]shutdown
[R2-GigabitEthernet0/0/2]quit
[R2]undo ip route-static 10.0.3.0 255.255.255.0
[R2]undo ip route-static 10.0.13.0 255.255.255.0

[R3]interface GigabitEthernet 0/0/2
[R3-GigabitEthernet0/0/2]shutdown
[R3-GigabitEthernet0/0/2]quit
[R3]undo ip route-static 10.0.12.0 255.255.255.0


Step 3 Additional address configuration
Configure the following additional interfaces for R2 and R3.

[R2]interface GigabitEthernet 0/0/0
[R2-GigabitEthernet0/0/0]ip address 10.0.13.2 24

[R3]interface GigabitEthernet0/0/1
[R3-GigabitEthernet0/0/1]ip address 10.0.12.3 24


M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 4 Routing Configuration

HC Series HUAWEI TECHNOLOGIES Page63

Verify that R1 and R2 can communicate with one another over the 10.0.13.0
network.
<R1>ping 10.0.13.2
PING 10.0.13.2: 56 data bytes, press CTRL_C to break
Reply from 10.0.13.2: bytes=56 Sequence=1 ttl=255 time=30 ms
Reply from 10.0.13.2: bytes=56 Sequence=2 ttl=255 time=30 ms
Reply from 10.0.13.2: bytes=56 Sequence=3 ttl=255 time=30 ms
Reply from 10.0.13.2: bytes=56 Sequence=4 ttl=255 time=30 ms
Reply from 10.0.13.2: bytes=56 Sequence=5 ttl=255 time=30 ms

--- 10.0.13.2 ping statistics ---
5 packet(s) transmitted
5 packet(s) received
0.00% packet loss
round-trip min/avg/max = 30/30/30 ms

Verify that R2 can successfully reach R3 over the 10.0.12.0 network.
<R2>ping 10.0.12.3
PING 10.0.12.2: 56 data bytes, press CTRL_C to break
Reply from 10.0.12.3: bytes=56 Sequence=1 ttl=255 time=31 ms
Reply from 10.0.12.3: bytes=56 Sequence=2 ttl=255 time=31 ms
Reply from 10.0.12.3: bytes=56 Sequence=3 ttl=255 time=41 ms
Reply from 10.0.12.3: bytes=56 Sequence=4 ttl=255 time=31 ms
Reply from 10.0.12.3: bytes=56 Sequence=5 ttl=255 time=41 ms

--- 10.0.12.3 ping statistics ---
5 packet(s) transmitted
5 packet(s) received
0.00% packet loss
round-trip min/avg/max = 31/35/41 ms

Step 4 Configure RIPv1.
Enable RIP on R1, and then advertise the 10.0.0.0 network segment.
[R1]rip 1
[R1-rip-1]network 10.0.0.0

Enable RIP on R2, and then advertise the 10.0.0.0 network segment.
[R2]rip 1
[R2-rip-1]network 10.0.0.0
M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 4 Routing Configuration

Page64 HUAWEI TECHNOLOGIES HC Series


Enable RIP on R3, and then advertise the 10.0.0.0 network segment.
[R3]rip 1
[R3-rip-1]network 10.0.0.0

Step 5 Verify RIPv1 routes.
View the routing tables of R1, R2, and R3. Make sure that these routers have
learned the RIP routes that are highlighted in gray in the following command
output.
<R1>display ip routing-table
Route Flags: R - relay, D - download to fib
----------------------------------------------------------------------------
Routing Tables: Public
Destinations : 13 Routes : 13

Destination/Mask Proto Pre Cost Flags NextHop Interface

10.0.1.0/24 Direct 0 0 D 10.0.1.1 LoopBack0
10.0.1.1/32 Direct 0 0 D 127.0.0.1 LoopBack0
10.0.1.255/32 Direct 0 0 D 127.0.0.1 LoopBack0
10.0.2.0/24 RIP 100 1 D 10.0.13.2 GigabitEthernet0/0/0
10.0.3.0/24 RIP 100 2 D 10.0.13.2 GigabitEthernet0/0/0
10.0.12.0/24 RIP 100 1 D 10.0.13.2 GigabitEthernet0/0/0
10.0.13.0/24 Direct 0 0 D 10.0.13.1 GigabitEthernet0/0/0
10.0.13.1/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/0
10.0.13.255/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/0
127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0
127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
127.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
255.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0

<R2>display ip routing-table
Route Flags: R - relay, D - download to fib
----------------------------------------------------------------------------
Routing Tables: Public
Destinations : 15 Routes : 15

Destination/Mask Proto Pre Cost Flags NextHop Interface

10.0.1.0/24 RIP 100 1 D 10.0.13.1 GigabitEthernet0/0/0
M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 4 Routing Configuration

HC Series HUAWEI TECHNOLOGIES Page65

10.0.2.0/24 Direct 0 0 D 10.0.2.2 LoopBack0
10.0.2.2/32 Direct 0 0 D 127.0.0.1 LoopBack0
10.0.2.255/32 Direct 0 0 D 127.0.0.1 LoopBack0
10.0.3.0/24 RIP 100 1 D 10.0.12.3 GigabitEthernet0/0/1
10.0.12.0/24 Direct 0 0 D 10.0.12.2 GigabitEthernet0/0/1
10.0.12.2/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/1
10.0.12.255/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/1
10.0.13.0/24 Direct 0 0 D 10.0.13.2 GigabitEthernet0/0/0
10.0.13.2/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/0
10.0.13.255/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/0
127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0
127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
127.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
255.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0

<R3>display ip routing-table
Route Flags: R - relay, D - download to fib
----------------------------------------------------------------------------
Routing Tables: Public
Destinations : 13 Routes : 13

Destination/Mask Proto Pre Cost Flags NextHop Interface

10.0.1.0/24 RIP 100 2 D 10.0.12.2 GigabitEthernet0/0/1
10.0.2.0/24 RIP 100 1 D 10.0.12.2 GigabitEthernet0/0/1
10.0.3.0/24 Direct 0 0 D 10.0.3.3 LoopBack0
10.0.3.3/32 Direct 0 0 D 127.0.0.1 LoopBack0
10.0.3.255/32 Direct 0 0 D 127.0.0.1 LoopBack0
10.0.12.0/24 Direct 0 0 D 10.0.12.3 GigabitEthernet0/0/1
10.0.12.3/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/1
10.0.12.255/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/1
10.0.13.0/24 RIP 100 1 D 10.0.12.2 GigabitEthernet0/0/1
127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0
127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
127.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
255.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0

Test connectivity from R1 to IP address 10.0.23.3. R1 and R3 can
communicate with one another.



M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 4 Routing Configuration

Page66 HUAWEI TECHNOLOGIES HC Series

[R1]ping 10.0.12.3
PING 10.0.12.3: 56 data bytes, press CTRL_C to break
Reply from 10.0.12.3: bytes=56 Sequence=1 ttl=254 time=70 ms
Reply from 10.0.12.3: bytes=56 Sequence=2 ttl=254 time=65 ms
Reply from 10.0.12.3: bytes=56 Sequence=3 ttl=254 time=65 ms
Reply from 10.0.12.3: bytes=56 Sequence=4 ttl=254 time=65 ms
Reply from 10.0.12.3: bytes=56 Sequence=5 ttl=254 time=65 ms

--- 10.0.12.3 ping statistics ---
5 packet(s) transmitted
5 packet(s) received
0.00% packet loss
round-trip min/avg/max = 65/66/70 ms

The debugging command can be used to view RIP periodic updates.
Run the debugging command to enable the RIP debugging function. The
debugging command can be used only in the user view. To identify the
currently enabled debugging information, use the display debugging
command. Run the terminal debugging command to display the debugging
information.
The information about RIP interactions between routers is displayed.
<R1>debugging rip 1
<R1>display debugging
RIP Process id: 1
Debugs ON: SEND, RECEIVE, PACKET, TIMER, EVENT, BRIEF,
JOB, ROUTE-PROCESSING, ERROR,
REPLAY-PROTECT, GR
<R1>terminal debugging
Info: Current terminal debugging is on.
<R1>
Nov 29 2013 09:45:07.860.1+00:00 R1 RIP/7/DBG: 6: 12734: RIP 1: Receiving v1
response on GigabitEthernet0/0/0 from 10.0.13.2 with 3 RTEs
<R1>
Nov 29 2013 09:45:07.860.2+00:00 R1 RIP/7/DBG: 6: 12785: RIP 1: Receive response
from 10.0.13.2 on GigabitEthernet0/0/0
<R1>
Nov 29 2013 09:45:07.860.3+00:00 R1 RIP/7/DBG: 6: 12796: Packet: Version 1, Cmd
response, Length 64
<R1>
Nov 29 2013 09:45:07.860.4+00:00 R1 RIP/7/DBG: 6: 12845: Dest 10.0.2.0, Cost 1
<R1>
M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 4 Routing Configuration

HC Series HUAWEI TECHNOLOGIES Page67

Nov 29 2013 09:45:07.860.5+00:00 R1 RIP/7/DBG: 6: 12845: Dest 10.0.3.0, Cost 2
<R1>
Nov 29 2013 09:45:07.860.6+00:00 R1 RIP/7/DBG: 6: 12845: Dest 10.0.12.0, Cost
1
<R1>
Nov 29 2013 09:45:09.370.1+00:00 R1 RIP/7/DBG: 25: 5071: RIP 1: Periodic timer
expired for interface GigabitEthernet0/0/1

Run the undo debugging rip <process-id> or undo debugging all
command to disable the debugging functions.
<R1>undo debugging rip 1

Individual parameters can be specified to control the debugging information
viewed. For example, the debugging rip 1 event command allows for only
periodical update events sent or received by routers to be viewed. The
question mark (?) can be added to the command to query other parameters.
<R1>debugging rip 1 event
<R1>
Nov 29 2013 10:00:04.880.1+00:00 R1 RIP/7/DBG: 25: 5719: RIP 1: Periodic timer
expired for interface GigabitEthernet0/0/0 (10.0.13.1) and its added to periodic
update queue
<R1>
Nov 29 2013 10:00:04.890.1+00:00 R1 RIP/7/DBG: 25: 6048: RIP 1: Interface
GigabitEthernet0/0/0 (10.0.13.1) is deleted from the periodic update queue

<R1>undo debugging all
Info: All possible debugging has been turned off

Warning: If too many debugging functions are enabled, a large number of
router resources will be utilized that may result in system service failure.
Therefore, the use of commands (such as debug all) for enabling debugging
functions in batches should be performed with caution.
Step 6 Configure RIPv2.
After the preceding configuration, you need to configure only version 2 in the
RIP sub view.
[R1]rip 1
[R1-rip-1]version 2


M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 4 Routing Configuration

Page68 HUAWEI TECHNOLOGIES HC Series

[R2]rip 1
[R2-rip-1]version 2

[R3]rip 1
[R3-rip-1]version 2

Step 7 Verify RIPv2 routes.
View the routing tables of R1, R2, and R3.
Run the display ip routing-table command to view the routing tables of R1,
R2, and R3. Compare the routes that are highlighted with RIPv1 routes.
<R1>display ip routing-table
Route Flags: R - relay, D - download to fib
----------------------------------------------------------------------------
Routing Tables: Public
Destinations : 13 Routes : 13

Destination/Mask Proto Pre Cost Flags NextHop Interface

10.0.1.0/24 Direct 0 0 D 10.0.1.1 LoopBack0
10.0.1.1/32 Direct 0 0 D 127.0.0.1 LoopBack0
10.0.1.255/32 Direct 0 0 D 127.0.0.1 LoopBack0
10.0.2.0/24 RIP 100 1 D 10.0.13.2 GigabitEthernet0/0/0
10.0.3.0/24 RIP 100 2 D 10.0.13.2 GigabitEthernet0/0/0
10.0.12.0/24 RIP 100 1 D 10.0.13.2 GigabitEthernet0/0/0
10.0.13.0/24 Direct 0 0 D 10.0.13.1 GigabitEthernet0/0/0
10.0.13.1/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/0
10.0.13.255/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/0
127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0
127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
127.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
255.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0



<R2>display ip routing-table
Route Flags: R - relay, D - download to fib
----------------------------------------------------------------------------
Routing Tables: Public
Destinations : 15 Routes : 15

M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 4 Routing Configuration

HC Series HUAWEI TECHNOLOGIES Page69

Destination/Mask Proto Pre Cost Flags NextHop Interface

10.0.1.0/24 RIP 100 1 D 10.0.13.1 GigabitEthernet0/0/0
10.0.2.0/24 Direct 0 0 D 10.0.2.2 LoopBack0
10.0.2.2/32 Direct 0 0 D 127.0.0.1 LoopBack0
10.0.2.255/32 Direct 0 0 D 127.0.0.1 LoopBack0
10.0.3.0/24 RIP 100 1 D 10.0.12.3 GigabitEthernet0/0/1
10.0.12.0/24 Direct 0 0 D 10.0.12.2 GigabitEthernet0/0/1
10.0.12.2/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/1
10.0.12.255/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/1
10.0.13.0/24 Direct 0 0 D 10.0.13.2 GigabitEthernet0/0/0
10.0.13.2/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/0
10.0.13.255/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/0
127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0
127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
127.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
255.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0

[R3]display ip routing-table
Route Flags: R - relay, D - download to fib
----------------------------------------------------------------------------
Routing Tables: Public
Destinations : 13 Routes : 13

Destination/Mask Proto Pre Cost Flags NextHop Interface

10.0.1.0/24 RIP 100 2 D 10.0.12.2 GigabitEthernet0/0/1
10.0.2.0/24 RIP 100 1 D 10.0.12.2 GigabitEthernet0/0/1
10.0.3.0/24 Direct 0 0 D 10.0.3.3 LoopBack0
10.0.3.3/32 Direct 0 0 D 127.0.0.1 LoopBack0
10.0.3.255/32 Direct 0 0 D 127.0.0.1 LoopBack0
10.0.12.0/24 Direct 0 0 D 10.0.12.3 GigabitEthernet0/0/1
10.0.12.3/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/1
10.0.12.255/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/1
10.0.13.0/24 RIP 100 1 D 10.0.12.2 GigabitEthernet0/0/1
127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0
127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
127.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
255.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0

Test connectivity from R1 to the IP destination 10.0.12.3 on interface Gigabit
Ethernet 0/0/2 of R3.
M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 4 Routing Configuration

Page70 HUAWEI TECHNOLOGIES HC Series

<R1>ping 10.0.12.3
PING 10.0.12.3: 56 data bytes, press CTRL_C to break
Reply from 10.0.12.3: bytes=56 Sequence=1 ttl=254 time=74 ms
Reply from 10.0.12.3: bytes=56 Sequence=2 ttl=254 time=75 ms
Reply from 10.0.12.3: bytes=56 Sequence=3 ttl=254 time=75 ms
Reply from 10.0.12.3: bytes=56 Sequence=4 ttl=254 time=75 ms
Reply from 10.0.12.3: bytes=56 Sequence=5 ttl=254 time=75 ms

--- 10.0.12.3 ping statistics ---
5 packet(s) transmitted
5 packet(s) received
0.00% packet loss
round-trip min/avg/max = 74/74/75 ms

The debugging command can be used to view the RIPv2 periodic updates.
<R1>terminal debugging
Info: Current terminal debugging is on.
<R1>debugging rip 1 event
<R1>
Nov 29 2013 10:41:04.490.1+00:00 R1 RIP/7/DBG: 25: 5719: RIP 1: Periodic timer
expired for interface GigabitEthernet0/0/0 (10.0.13.1) and its added to periodic
update queue
<R1>
Nov 29 2013 10:41:04.500.1+00:00 R1 RIP/7/DBG: 25: 6048: RIP 1: Interface
GigabitEthernet0/0/0 (10.0.13.1) is deleted from the periodic update queue

<R1>undo debugging rip 1

<R1>debugging rip 1 packet
<R1>
Nov 29 2013 10:43:07.770.1+00:00 R1 RIP/7/DBG: 6: 12776: RIP 1: Sending response
on interface GigabitEthernet0/0/0 from 10.0.13.1 to 224.0.0.9
<R1>
Nov 29 2013 10:43:07.770.2+00:00 R1 RIP/7/DBG: 6: 12796: Packet: Version 2, Cmd
response, Length 24
<R1>
Nov 29 2013 10:43:07.770.3+00:00 R1 RIP/7/DBG: 6: 12864: Dest 10.0.1.0/24, Nexthop
0.0.0.0, Cost 1, Tag 0

<R1>undo debugging rip 1
M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 4 Routing Configuration

HC Series HUAWEI TECHNOLOGIES Page71

Additional Exercises: Analyzing and Verifying
When using RIPv1, a router sends network IDs and other route update
information to its neighbor routers without sending subnet masks. How do
neighbor routers process the route update information and generate the
corresponding subnet masks?
How are RIPv1 and RIPv2 compatible with each other?
Final Configuration
<R1>display current-configuration
[V200R003C00SPC200]
#
sysname R1
#
interface GigabitEthernet0/0/0
ip address 10.0.13.1 255.255.255.0
#
interface GigabitEthernet0/0/1
shutdown
ip address 10.0.12.1 255.255.255.0
#
interface LoopBack0
ip address 10.0.1.1 255.255.255.0
#
rip 1
version 2
network 10.0.0.0
#
user-interface con 0
authentication-mode password
set authentication password cipher %$%$+L'YR&IZt'4,)>-*#lH",}%K-oJ_M9+'lOU~bD
(\WTqB}%N,%$%$
user-interface vty 0 4
#
return





M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 4 Routing Configuration

Page72 HUAWEI TECHNOLOGIES HC Series

<R2>display current-configuration
[V200R003C00SPC200]
#
sysname R2
#
interface GigabitEthernet0/0/0
ip address 10.0.13.2 255.255.255.0
#
interface GigabitEthernet0/0/1
ip address 10.0.12.2 255.255.255.0
#
interface GigabitEthernet0/0/2
shutdown
ip address 10.0.23.2 255.255.255.0
#
interface LoopBack0
ip address 10.0.2.2 255.255.255.0
#
rip 1
version 2
network 10.0.0.0
#
user-interface con 0
authentication-mode password
set authentication password cipher %$%$1=cd%b%/O%Id-8X:by1N,+s}'4wD6TvO<I|/pd#
#44C@+s#,%$%$
user-interface vty 0 4
#
return


<R3>display current-configuration
[V200R003C00SPC200]
#
sysname R3
#
interface GigabitEthernet0/0/0
shutdown
ip address 10.0.13.3 255.255.255.0
#
interface GigabitEthernet0/0/1
ip address 10.0.12.3 255.255.255.0
#
M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 4 Routing Configuration

HC Series HUAWEI TECHNOLOGIES Page73

interface GigabitEthernet0/0/2
shutdown
ip address 10.0.23.3 255.255.255.0
#
interface LoopBack0
ip address 10.0.3.3 255.255.255.0
#
rip 1
version 2
network 10.0.0.0
#
user-interface con 0
authentication-mode password
set authentication password cipher %$%$ksXDMg7Ry6yUU:63:DQ),#/sQg"@*S\U#.s.bHW
xQ,y%#/v,%$%$
user-interface vty 0 4
#
return








M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 4 Routing Configuration

Page74 HUAWEI TECHNOLOGIES HC Series

Lab 4-3 RIPv2 Route Aggregation and Authentication
Learning Objectives
As a result of this lab section, you should achieve the following tasks:
Aggregation of routes in RIPv2
Implementation of authentication between RIP peers
Troubleshoot RIP peer authentication failures.
Topology

Figure 4.3 RIPv2 route aggregation and authentication topology


M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 4 Routing Configuration

HC Series HUAWEI TECHNOLOGIES Page75

Scenario
As the network administrator of a small company you are responsible for the
support of a RIPv2 based enterprise network. In order to better manage and
optimize the routing table, route aggregation is required.
Additionally, concerns over the insertion of rogue devices into the network that
may affect routing tables means that RIP authentication is required to protect
the network.
Tasks
Step 1 Preparing the environment
If you are starting this section with a non-configured device begin here and
then move to step 2. For those continuing from previous labs, begin at step 2.
Configure the base system information and addressing for R1, R2 and R3 on
the network.

<Huawei>system-view
Enter system view, return user view with Ctrl+Z.
[Huawei]sysname R1
[R1]interface GigabitEthernet 0/0/0
[R1-GigabitEthernet0/0/0]ip address 10.0.13.1 24
[R1-GigabitEthernet0/0/0]quit
[R1]interface LoopBack 0
[R1-LoopBack0]ip address 10.0.1.1 24

<Huawei>system-view
Enter system view, return user view with Ctrl+Z.
[Huawei]sysname R2
[R2]interface GigabitEthernet 0/0/0
[R2-GigabitEthernet0/0/0]ip address 10.0.13.2 24
[R2-GigabitEthernet0/0/0]quit
[R2]interface GigabitEthernet 0/0/1
[R2-GigabitEthernet0/0/1]ip address 10.0.12.2 24
[R2-GigabitEthernet0/0/1]quit
[R2]interface LoopBack 0
[R2-LoopBack0]ip address 10.0.2.2 24


M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 4 Routing Configuration

Page76 HUAWEI TECHNOLOGIES HC Series

<Huawei>system-view
Enter system view, return user view with Ctrl+Z.
[Huawei]sysname R3
[R3]interface GigabitEthernet 0/0/1
[R3-GigabitEthernet0/0/1]ip address 10.0.12.3 24
[R3-GigabitEthernet0/0/1]quit
[R3]interface LoopBack 0
[R3-LoopBack0]ip address 10.0.3.3 24

After the IP addresses have been configured for the interfaces, test the
network connectivity.
<R1>ping 10.0.13.2
PING 10.0.13.2: 56 data bytes, press CTRL_C to break
Reply from 10.0.13.2: bytes=56 Sequence=1 ttl=255 time=30 ms
Reply from 10.0.13.2: bytes=56 Sequence=2 ttl=255 time=30 ms
Reply from 10.0.13.2: bytes=56 Sequence=3 ttl=255 time=30 ms
Reply from 10.0.13.2: bytes=56 Sequence=4 ttl=255 time=30 ms
Reply from 10.0.13.2: bytes=56 Sequence=5 ttl=255 time=30 ms

--- 10.0.13.2 ping statistics ---
5 packet(s) transmitted
5 packet(s) received
0.00% packet loss
round-trip min/avg/max = 30/30/30 ms

<R2>ping 10.0.12.3
PING 10.0.12.3: 56 data bytes, press CTRL_C to break
Reply from 10.0.12.3: bytes=56 Sequence=1 ttl=255 time=31 ms
Reply from 10.0.12.3: bytes=56 Sequence=2 ttl=255 time=31 ms
Reply from 10.0.12.3: bytes=56 Sequence=3 ttl=255 time=41 ms
Reply from 10.0.12.3: bytes=56 Sequence=4 ttl=255 time=31 ms
Reply from 10.0.12.3: bytes=56 Sequence=5 ttl=255 time=41 ms

--- 10.0.12.3 ping statistics ---
5 packet(s) transmitted
5 packet(s) received
0.00% packet loss
round-trip min/avg/max = 31/35/41 ms



M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 4 Routing Configuration

HC Series HUAWEI TECHNOLOGIES Page77

Configure RIPv2 on R1, R2, and R3.
[R1]rip 1
[R1-rip-1]version 2
[R1-rip-1]network 10.0.0.0

[R2]rip 1
[R2-rip-1]version 2
[R2-rip-1]network 10.0.0.0

[R3]rip 1
[R3-rip-1]version 2
[R3-rip-1]network 10.0.0.0

Step 2 Configuration of additional loopback addresses
Establish additional loopback interfaces to represent multiple networks on R3.
[R3-LoopBack0]interface LoopBack 2
[R3-LoopBack2]ip address 172.16.0.1 24
[R3-LoopBack2]interface LoopBack 3
[R3-LoopBack3]ip address 172.16.1.1 24
[R3-LoopBack3]interface LoopBack 4
[R3-LoopBack4]ip address 172.16.2.1 24
[R3-LoopBack4]interface LoopBack 5
[R3-LoopBack5]ip address 172.16.3.1 24

Step 3 Advertize the loopback addresses in RIP.
The networks for the configured loopback interfaces need to be advertized.
Advertise the 172.16.0.0 network range on R3.

[R3]rip
[R3-rip-1]network 172.16.0.0

View the routing table of R1 to verify the new networks are being advertized.
<R1>display ip routing-table
Route Flags: R - relay, D - download to fib
----------------------------------------------------------------------------
Routing Tables: Public
Destinations : 17 Routes : 17

M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 4 Routing Configuration

Page78 HUAWEI TECHNOLOGIES HC Series

Destination/Mask Proto Pre Cost Flags NextHop Interface

10.0.1.0/24 Direct 0 0 D 10.0.1.1 LoopBack0
10.0.1.1/32 Direct 0 0 D 127.0.0.1 LoopBack0
10.0.1.255/32 Direct 0 0 D 127.0.0.1 LoopBack0
10.0.2.0/24 RIP 100 1 D 10.0.13.2 GigabitEthernet0/0/0
10.0.3.0/24 RIP 100 2 D 10.0.13.2 GigabitEthernet0/0/0
10.0.12.0/24 RIP 100 1 D 10.0.13.2 GigabitEthernet0/0/0
10.0.13.0/24 Direct 0 0 D 10.0.13.1 GigabitEthernet0/0/0
10.0.13.1/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/0
10.0.13.255/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/0
127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0
127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
127.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
172.16.0.0/24 RIP 100 2 D 10.0.13.2 GigabitEthernet0/0/0
172.16.1.0/24 RIP 100 2 D 10.0.13.2 GigabitEthernet0/0/0
172.16.2.0/24 RIP 100 2 D 10.0.13.2 GigabitEthernet0/0/0
172.16.3.0/24 RIP 100 2 D 10.0.13.2 GigabitEthernet0/0/0
255.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0

The information in grey shows that R1 has learned specific routes but not
aggregated routes.
Test network connectivity from R1 to the 172.16.0.0 network range.
<R1>ping 172.16.0.1
PING 172.16.0.1: 56 data bytes, press CTRL_C to break
Reply from 172.16.0.1: bytes=56 Sequence=1 ttl=254 time=80 ms
Reply from 172.16.0.1: bytes=56 Sequence=2 ttl=254 time=79 ms
Reply from 172.16.0.1: bytes=56 Sequence=3 ttl=254 time=79 ms
Reply from 172.16.0.1: bytes=56 Sequence=4 ttl=254 time=79 ms
Reply from 172.16.0.1: bytes=56 Sequence=5 ttl=254 time=79 ms

--- 172.16.0.1 ping statistics ---
5 packet(s) transmitted
5 packet(s) received
0.00% packet loss
round-trip min/avg/max = 79/79/80 ms


M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 4 Routing Configuration

HC Series HUAWEI TECHNOLOGIES Page79

Step 4 Configure RIP manual route aggregation on R2.
Run the rip summary-address command on S1/0/0 of R2 to configure RIP
route aggregation. The four routes (172.16.0.0/24, 172.16.1.0/24,
172.16.2.0/24, and 172.16.3.0/24) are to be aggregated into one route,
172.16.0.0/16.
[R2]interface GigabitEthernet0/0/0
[R2-GigabitEthernet0/0/0]rip summary-address 172.16.0.0 255.255.0.0

View the routing table of R1 that should now include an aggregated route.
<R1>display ip routing-table
Route Flags: R - relay, D - download to fib
----------------------------------------------------------------------------
Routing Tables: Public
Destinations : 14 Routes : 14

Destination/Mask Proto Pre Cost Flags NextHop Interface

10.0.1.0/24 Direct 0 0 D 10.0.1.1 LoopBack0
10.0.1.1/32 Direct 0 0 D 127.0.0.1 LoopBack0
10.0.1.255/32 Direct 0 0 D 127.0.0.1 LoopBack0
10.0.2.0/24 RIP 100 1 D 10.0.13.2 GigabitEthernet0/0/0
10.0.3.0/24 RIP 100 2 D 10.0.13.2 GigabitEthernet0/0/0
10.0.12.0/24 RIP 100 1 D 10.0.13.2 GigabitEthernet0/0/0
10.0.13.0/24 Direct 0 0 D 10.0.13.1 GigabitEthernet0/0/0
10.0.13.1/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/0
10.0.13.255/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/0
127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0
127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
127.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
172.16.0.0/16 RIP 100 2 D 10.0.13.2 GigabitEthernet0/0/0
255.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0

The highlighted information shows the aggregated route. There is now no
specific route is listed in the routing table.



M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 4 Routing Configuration

Page80 HUAWEI TECHNOLOGIES HC Series

Verify that the routes are still supported for the 172.16.0.0 network range.
<R1>ping 172.16.0.1
PING 172.16.0.1: 56 data bytes, press CTRL_C to break
Reply from 172.16.0.1: bytes=56 Sequence=1 ttl=254 time=60 ms
Reply from 172.16.0.1: bytes=56 Sequence=2 ttl=254 time=59 ms
Reply from 172.16.0.1: bytes=56 Sequence=3 ttl=254 time=80 ms
Reply from 172.16.0.1: bytes=56 Sequence=4 ttl=254 time=60 ms
Reply from 172.16.0.1: bytes=56 Sequence=5 ttl=254 time=60 ms

--- 172.16.0.1 ping statistics ---
5 packet(s) transmitted
5 packet(s) received
0.00% packet loss
round-trip min/avg/max = 59/63/80 ms

The preceding information shows that route aggregation reduces the size of
the routing table without affecting communication to aggregated networks.
Step 5 Configure RIP authentication.
Configure plain text authentication between R1 and R2 and MD5 based
authentication between R2 and R3. The authentication password in all cases
should be huawei.
[R1]interface GigabitEthernet0/0/0
[R1-GigabitEthernet0/0/0]rip authentication-mode simple huawei

[R2]interface GigabitEthernet0/0/0
[R2-GigabitEthernet0/0/0]rip authentication-mode simple huawei
[R2-GigabitEthernet0/0/0]quit
[R2]interface GigabitEthernet0/0/1
[R2-GigabitEthernet0/0/1]rip authentication-mode md5 usual huawei

[R3]interface GigabitEthernet0/0/1
[R3-GigabitEthernet0/0/1]rip authentication-mode md5 usual huawei





M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 4 Routing Configuration

HC Series HUAWEI TECHNOLOGIES Page81

After the configuration is complete, verify that the routes are not affected.
<R1>display ip routing-table
Route Flags: R - relay, D - download to fib
----------------------------------------------------------------------------
Routing Tables: Public
Destinations : 14 Routes : 14

Destination/Mask Proto Pre Cost Flags NextHop Interface

10.0.1.0/24 Direct 0 0 D 10.0.1.1 LoopBack0
10.0.1.1/32 Direct 0 0 D 127.0.0.1 LoopBack0
10.0.1.255/32 Direct 0 0 D 127.0.0.1 LoopBack0
10.0.2.0/24 RIP 100 1 D 10.0.13.2 GigabitEthernet0/0/0
10.0.3.0/24 RIP 100 2 D 10.0.13.2 GigabitEthernet0/0/0
10.0.12.0/24 RIP 100 1 D 10.0.13.2 GigabitEthernet0/0/0
10.0.13.0/24 Direct 0 0 D 10.0.13.1 GigabitEthernet0/0/0
10.0.13.1/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/0
10.0.13.255/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/0
127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0
127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
127.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
172.16.0.0/16 RIP 100 2 D 10.0.13.2 GigabitEthernet0/0/0
255.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0

<R2>display ip routing-table
Route Flags: R - relay, D - download to fib
----------------------------------------------------------------------------
Routing Tables: Public
Destinations : 19 Routes : 19

Destination/Mask Proto Pre Cost Flags NextHop Interface

10.0.1.0/24 RIP 100 1 D 10.0.13.1 GigabitEthernet0/0/0
10.0.2.0/24 Direct 0 0 D 10.0.2.2 LoopBack0
10.0.2.2/32 Direct 0 0 D 127.0.0.1 LoopBack0
10.0.2.255/32 Direct 0 0 D 127.0.0.1 LoopBack0
10.0.3.0/24 RIP 100 1 D 10.0.12.3 GigabitEthernet0/0/1
10.0.12.0/24 Direct 0 0 D 10.0.12.2 GigabitEthernet0/0/1
10.0.12.2/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/1
10.0.12.255/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/1
10.0.13.0/24 Direct 0 0 D 10.0.13.2 GigabitEthernet0/0/0
10.0.13.2/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/0
M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 4 Routing Configuration

Page82 HUAWEI TECHNOLOGIES HC Series

10.0.13.255/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/0
127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0
127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
127.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
172.16.0.0/24 RIP 100 1 D 10.0.12.3 GigabitEthernet0/0/1
172.16.1.0/24 RIP 100 1 D 10.0.12.3 GigabitEthernet0/0/1
172.16.2.0/24 RIP 100 1 D 10.0.12.3 GigabitEthernet0/0/1
172.16.3.0/24 RIP 100 1 D 10.0.12.3 GigabitEthernet0/0/1
255.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0

<R3>display ip routing-table
Route Flags: R - relay, D - download to fib
----------------------------------------------------------------------------
Routing Tables: Public
Destinations : 25 Routes : 25
Destination/Mask Proto Pre Cost Flags NextHop Interface

10.0.1.0/24 RIP 100 2 D 10.0.12.2 GigabitEthernet0/0/1
10.0.2.0/24 RIP 100 1 D 10.0.12.2 GigabitEthernet0/0/1
10.0.3.0/24 Direct 0 0 D 10.0.3.3 LoopBack0
10.0.3.3/32 Direct 0 0 D 127.0.0.1 LoopBack0
10.0.3.255/32 Direct 0 0 D 127.0.0.1 LoopBack0
10.0.12.0/24 Direct 0 0 D 10.0.12.3 GigabitEthernet0/0/1
10.0.12.3/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/1
10.0.12.255/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/1
10.0.13.0/24 RIP 100 1 D 10.0.12.2 GigabitEthernet0/0/1
127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0
127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
127.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
172.16.0.0/24 Direct 0 0 D 172.16.0.1 LoopBack2
172.16.0.1/32 Direct 0 0 D 127.0.0.1 LoopBack2
172.16.0.255/32 Direct 0 0 D 127.0.0.1 LoopBack2
172.16.1.0/24 Direct 0 0 D 172.16.1.1 LoopBack3
172.16.1.1/32 Direct 0 0 D 127.0.0.1 LoopBack3
172.16.1.255/32 Direct 0 0 D 127.0.0.1 LoopBack3
172.16.2.0/24 Direct 0 0 D 172.16.2.1 LoopBack4
172.16.2.1/32 Direct 0 0 D 127.0.0.1 LoopBack4
172.16.2.255/32 Direct 0 0 D 127.0.0.1 LoopBack4
172.16.3.0/24 Direct 0 0 D 172.16.3.1 LoopBack5
172.16.3.1/32 Direct 0 0 D 127.0.0.1 LoopBack5
172.16.3.255/32 Direct 0 0 D 127.0.0.1 LoopBack5
255.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0

M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 4 Routing Configuration

HC Series HUAWEI TECHNOLOGIES Page83

Step 6 Generate and rectify RIPv2 authenticaion faults.
Change the authentication password on G0/0/0 of R2 to huawei2.
[R2]interface GigabitEthernet0/0/0
[R2-GigabitEthernet0/0/0]rip authentication-mode simple huawei2

View the routing table of R1.
<R1>display ip routing-table
Route Flags: R - relay, D - download to fib
----------------------------------------------------------------------------
Routing Tables: Public
Destinations : 10 Routes : 10

Destination/Mask Proto Pre Cost Flags NextHop Interface

10.0.1.0/24 Direct 0 0 D 10.0.1.1 LoopBack0
10.0.1.1/32 Direct 0 0 D 127.0.0.1 LoopBack0
10.0.1.255/32 Direct 0 0 D 127.0.0.1 LoopBack0
10.0.13.0/24 Direct 0 0 D 10.0.13.1 GigabitEthernet0/0/0
10.0.13.1/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/0
10.0.13.255/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/0
127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0
127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
127.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
255.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0

Since R1 and R2 use different RIP authentication passwords, R1 will not
receive any advertsed RIP routes from R2.
Restore the authentication password on G0/0/0 of R2 to huawei.
[R2]interface GigabitEthernet0/0/0
[R2- GigabitEthernet0/0/0]rip authentication-mode simple huawei

Change the authentication mode on G0/0/1 of R2 to plain text authentication.
[R2]interface GigabitEthernet0/0/1
[R2-GigabitEthernet0/0/1]rip authentication-mode simple huawei

Run the following command to delete the routes learned by R3 from R2 before
you change the authentication password.
View the routing table of R3.
M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 4 Routing Configuration

Page84 HUAWEI TECHNOLOGIES HC Series

<R3>display ip routing-table

Route Flags: R - relay, D - download to fib
----------------------------------------------------------------------------
Routing Tables: Public
Destinations : 22 Routes : 22

Destination/Mask Proto Pre Cost Flags NextHop Interface

10.0.3.0/24 Direct 0 0 D 10.0.3.3 LoopBack0
10.0.3.3/32 Direct 0 0 D 127.0.0.1 LoopBack0
10.0.3.255/32 Direct 0 0 D 127.0.0.1 LoopBack0
10.0.12.0/24 Direct 0 0 D 10.0.12.3 GigabitEthernet0/0/1
10.0.12.3/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/1
10.0.12.255/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/1
127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0
127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
127.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
172.16.0.0/24 Direct 0 0 D 172.16.0.1 LoopBack2
172.16.0.1/32 Direct 0 0 D 127.0.0.1 LoopBack2
172.16.0.255/32 Direct 0 0 D 127.0.0.1 LoopBack2
172.16.1.0/24 Direct 0 0 D 172.16.1.1 LoopBack3
172.16.1.1/32 Direct 0 0 D 127.0.0.1 LoopBack3
172.16.1.255/32 Direct 0 0 D 127.0.0.1 LoopBack3
172.16.2.0/24 Direct 0 0 D 172.16.2.1 LoopBack4
172.16.2.1/32 Direct 0 0 D 127.0.0.1 LoopBack4
172.16.2.255/32 Direct 0 0 D 127.0.0.1 LoopBack4
172.16.3.0/24 Direct 0 0 D 172.16.3.1 LoopBack5
172.16.3.1/32 Direct 0 0 D 127.0.0.1 LoopBack5
172.16.3.255/32 Direct 0 0 D 127.0.0.1 LoopBack5
255.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0

Since R2 and R3 use different RIP authentication modes, R3 cannot receive
any advertised RIP routes from R2.
Restore the authentication mode on G0/0/1 of R2 to MD5.
[R2]interface GigabitEthernet0/0/1
[R2-GigabitEthernet0/0/1]rip authentication-mode md5 usual huawei

Verify that routes in routing tables of R1, R2, and R3 have been restored. Note
that RIP updates routes periodically, so may take a moment to be restored.
<R1>display ip routing-table
M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 4 Routing Configuration

HC Series HUAWEI TECHNOLOGIES Page85

Route Flags: R - relay, D - download to fib
----------------------------------------------------------------------------
Routing Tables: Public
Destinations : 14 Routes : 14

Destination/Mask Proto Pre Cost Flags NextHop Interface

10.0.1.0/24 Direct 0 0 D 10.0.1.1 LoopBack0
10.0.1.1/32 Direct 0 0 D 127.0.0.1 LoopBack0
10.0.1.255/32 Direct 0 0 D 127.0.0.1 LoopBack0
10.0.2.0/24 RIP 100 1 D 10.0.13.2 GigabitEthernet0/0/0
10.0.3.0/24 RIP 100 2 D 10.0.13.2 GigabitEthernet0/0/0
10.0.12.0/24 RIP 100 1 D 10.0.13.2 GigabitEthernet0/0/0
10.0.13.0/24 Direct 0 0 D 10.0.13.1 GigabitEthernet0/0/0
10.0.13.1/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/0
10.0.13.255/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/0
127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0
127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
127.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
172.16.0.0/16 RIP 100 2 D 10.0.13.2 GigabitEthernet0/0/0
255.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0

[R2]display ip routing-table
Route Flags: R - relay, D - download to fib
----------------------------------------------------------------------------
Routing Tables: Public
Destinations : 19 Routes : 19

Destination/Mask Proto Pre Cost Flags NextHop Interface

10.0.1.0/24 RIP 100 1 D 10.0.13.1 GigabitEthernet0/0/0
10.0.2.0/24 Direct 0 0 D 10.0.2.2 LoopBack0
10.0.2.2/32 Direct 0 0 D 127.0.0.1 LoopBack0
10.0.2.255/32 Direct 0 0 D 127.0.0.1 LoopBack0
10.0.3.0/24 RIP 100 1 D 10.0.12.3 GigabitEthernet0/0/1
10.0.12.0/24 Direct 0 0 D 10.0.12.2 GigabitEthernet0/0/1
10.0.12.2/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/1
10.0.12.255/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/1
10.0.13.0/24 Direct 0 0 D 10.0.13.2 GigabitEthernet0/0/0
10.0.13.2/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/0
10.0.13.255/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/0
127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0
127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 4 Routing Configuration

Page86 HUAWEI TECHNOLOGIES HC Series

127.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
172.16.0.0/24 RIP 100 1 D 10.0.12.3 GigabitEthernet0/0/1
172.16.1.0/24 RIP 100 1 D 10.0.12.3 GigabitEthernet0/0/1
172.16.2.0/24 RIP 100 1 D 10.0.12.3 GigabitEthernet0/0/1
172.16.3.0/24 RIP 100 1 D 10.0.12.3 GigabitEthernet0/0/1
255.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0

<R3>display ip routing-table
Route Flags: R - relay, D - download to fib
----------------------------------------------------------------------------
Routing Tables: Public
Destinations : 25 Routes : 25
Destination/Mask Proto Pre Cost Flags NextHop Interface

10.0.1.0/24 RIP 100 2 D 10.0.12.2 GigabitEthernet0/0/1
10.0.2.0/24 RIP 100 1 D 10.0.12.2 GigabitEthernet0/0/1
10.0.3.0/24 Direct 0 0 D 10.0.3.3 LoopBack0
10.0.3.3/32 Direct 0 0 D 127.0.0.1 LoopBack0
10.0.3.255/32 Direct 0 0 D 127.0.0.1 LoopBack0
10.0.12.0/24 Direct 0 0 D 10.0.12.3 GigabitEthernet0/0/1
10.0.12.3/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/1
10.0.12.255/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/1
10.0.13.0/24 RIP 100 1 D 10.0.12.2 GigabitEthernet0/0/1
127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0
127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
127.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
172.16.0.0/24 Direct 0 0 D 172.16.0.1 LoopBack2
172.16.0.1/32 Direct 0 0 D 127.0.0.1 LoopBack2
172.16.0.255/32 Direct 0 0 D 127.0.0.1 LoopBack2
172.16.1.0/24 Direct 0 0 D 172.16.1.1 LoopBack3
172.16.1.1/32 Direct 0 0 D 127.0.0.1 LoopBack3
172.16.1.255/32 Direct 0 0 D 127.0.0.1 LoopBack3
172.16.2.0/24 Direct 0 0 D 172.16.2.1 LoopBack4
172.16.2.1/32 Direct 0 0 D 127.0.0.1 LoopBack4
172.16.2.255/32 Direct 0 0 D 127.0.0.1 LoopBack4
172.16.3.0/24 Direct 0 0 D 172.16.3.1 LoopBack5
172.16.3.1/32 Direct 0 0 D 127.0.0.1 LoopBack5
172.16.3.255/32 Direct 0 0 D 127.0.0.1 LoopBack5
255.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0

M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 4 Routing Configuration

HC Series HUAWEI TECHNOLOGIES Page87

Final Configuration
<R1>display current-configuration
[V200R003C00SPC200]
#
sysname R1
#
interface GigabitEthernet0/0/0
ip address 10.0.13.1 255.255.255.0
rip authentication-mode simple cipher %$%$S2AJ2_mJ)Hf++RSng6^NN|Xl%$%$
#
interface LoopBack0
ip address 10.0.1.1 255.255.255.0
#
rip 1
version 2
network 10.0.0.0
#
user-interface con 0
authentication-mode password
set authentication password cipher %$%$+L'YR&IZt'4,)>-*#lH",}%K-oJ_M9+'lOU~bD
(\WTqB}%N,%$%$
user-interface vty 0 4
#
return

<R2>display current-configuration
[V200R003C00SPC200]
#
sysname R2
#
interface GigabitEthernet0/0/0
ip address 10.0.13.2 255.255.255.0
rip authentication-mode simple cipher %$%$+Ob&JcQxU6mUJ(ZXLZY#OEXz%$%$
rip summary-address 172.16.0.0 255.255.0.0
#
interface GigabitEthernet0/0/1
ip address 10.0.12.2 255.255.255.0
rip authentication-mode md5 usual cipher %$%$C]'$.`NWGZ}|gLV%:XF>OG}|%$%$
#
interface LoopBack0
ip address 10.0.2.2 255.255.255.0
M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 4 Routing Configuration

Page88 HUAWEI TECHNOLOGIES HC Series

#
rip 1
version 2
network 10.0.0.0
#
user-interface con 0
authentication-mode password
set authentication password cipher %$%$1=cd%b%/O%Id-8X:by1N,+s}'4wD6TvO<I|/pd#
#44C@+s#,%$%$
user-interface vty 0 4
#
return


<R3>display current-configuration
[V200R003C00SPC200]
#
sysname R3
#
interface GigabitEthernet0/0/1
ip address 10.0.12.3 255.255.255.0
rip authentication-mode md5 usual cipher %$%$_5VL+wN6FNe]rVKbh[E(O=E>%$%$
#
interface LoopBack0
ip address 10.0.3.3 255.255.255.0
#
interface LoopBack2
ip address 172.16.0.1 255.255.255.0
#
interface LoopBack3
ip address 172.16.1.1 255.255.255.0
#
interface LoopBack4
ip address 172.16.2.1 255.255.255.0
#
interface LoopBack5
ip address 172.16.3.1 255.255.255.0
#
rip 1
version 2
network 10.0.0.0
network 172.16.0.0
#
M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 4 Routing Configuration

HC Series HUAWEI TECHNOLOGIES Page89

user-interface con 0
authentication-mode password
set authentication password cipher %$%$ksXDMg7Ry6yUU:63:DQ),#/sQg"@*S\U#.s.bHW
xQ,y%#/v,%$%$
user-interface vty 0 4
#
return

M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 4 Routing Configuration

Page90 HUAWEI TECHNOLOGIES HC Series

Lab 4-4 OSPF Single-Area Configuration
Learning Objectives
As a result of this lab section, you should achieve the following tasks:
Configuration of the Router-ID for OSPF.
Establish OSPF on a specified interface or network.
View OSPF operations using display commands.
Advertisement of default routes in OSPF.
Change of the OSPF hello interval and dead interval.
Famliarization with DR or BDR election on multi-access networks.
Change of the OSPF route priority to manipulate DR election.
Topology

Figure 4.4 OSPF single area topology

M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:
h
t
t
p
:/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 4 Routing Configuration

HC Series HUAWEI TECHNOLOGIES Page91

Scenario
As the network administrator of an establishing small enterprise, it is required
that a network be implemented using OSPF. Then network is to support a
single area and with consideration for future expansion it is requested that this
area be set as area 0. OSPF is required to advertise default routes and also
elect both a DR and BDR for network resiliency.
Tasks
Step 1 Prepare the environment
If you are starting this section with a non-configured device, begin here and
then move to step 3. For those continuing from previous labs, begin at step 2.
Establish the basic system configuration and addressing for the lab.

<Huawei>system-view
Enter system view, return user view with Ctrl+Z.
[Huawei]sysname R1
[R1]interface GigabitEthernet 0/0/1
[R1-GigabitEthernet 0/0/1]ip address 10.0.12.1 24
[R1-GigabitEthernet 0/0/1]quit
[R1]interface GigabitEthernet 0/0/0
[R1-GigabitEthernet0/0/0]ip address 10.0.13.1 24
[R1-GigabitEthernet0/0/0]quit
[R1]interface LoopBack 0
[R1-LoopBack0]ip address 10.0.1.1 24

<Huawei>system-view
Enter system view, return user view with Ctrl+Z.
[Huawei]sysname R2
[R2]interface GigabitEthernet 0/0/1
[R2-GigabitEthernet 0/0/1]ip address 10.0.12.2 24
[R2-GigabitEthernet 0/0/1]quit
[R2]interface LoopBack 0
[R2-LoopBack0]ip address 10.0.2.2 24




M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 4 Routing Configuration

Page92 HUAWEI TECHNOLOGIES HC Series

<Huawei>system-view
Enter system view, return user view with Ctrl+Z.
[Huawei]sysname R3
[R3]interface GigabitEthernet 0/0/0
[R3-GigabitEthernet0/0/0]ip address 10.0.13.3 24
[R3-GigabitEthernet0/0/0]quit
[R3]interface LoopBack 0
[R3-LoopBack0]ip address 10.0.3.3 24
[R3-LoopBack0]quit
[R3]interface LoopBack 2
[R3-LoopBack2]ip address 172.16.0.1 24

Step 2 Clean up the previous configuration.
Enable the interfaces necessary for this lab and disable those not needed.

[R1]interface GigabitEthernet 0/0/1
[R1-GigabitEthernet0/0/1]undo shutdown
[R1-GigabitEthernet0/0/1]quit

[R2]interface GigabitEthernet 0/0/0
[R2-GigabitEthernet0/0/0]undo rip summary-address 172.16.0.0 255.255.0.0
[R2-GigabitEthernet0/0/0]shutdown

[R3]interface GigabitEthernet 0/0/0
[R3-GigabitEthernet0/0/0]undo shutdown
[R3-GigabitEthernet0/0/0]quit
[R3]interface GigabitEthernet 0/0/1
[R3-GigabitEthernet0/0/1]shutdown
[R3-GigabitEthernet0/0/1]quit
[R3]undo interface LoopBack 3
Info: This operation may take a few seconds. Please wait for a moment...succeeded.
[R3]undo interface LoopBack 4
Info: This operation may take a few seconds. Please wait for a moment...succeeded.
[R3]undo interface LoopBack 5
Info: This operation may take a few seconds. Please wait for a moment...succeeded.

Remove the configured RIP authentication and RIP 1 process.

[R1]interface GigabitEthernet 0/0/0
[R1-GigabitEthernet0/0/0]undo rip authentication-mode
[R1-GigabitEthernet0/0/0]quit
M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 4 Routing Configuration

HC Series HUAWEI TECHNOLOGIES Page93

[R1]undo rip 1
Warning: The RIP process will be deleted. Continue?[Y/N]y

[R2]interface GigabitEthernet 0/0/0
[R2-GigabitEthernet0/0/0]undo rip authentication-mode
[R2-GigabitEthernet0/0/0]quit
[R2]interface GigabitEthernet 0/0/1
[R2-GigabitEthernet0/0/1]undo rip authentication-mode
[R2-GigabitEthernet0/0/1]quit
[R2]undo rip 1
Warning: The RIP process will be deleted. Continue?[Y/N]y

[R3]interface GigabitEthernet 0/0/1
[R3-GigabitEthernet0/0/1]undo rip authentication-mode
[R3-GigabitEthernet0/0/1]quit
[R3]undo rip 1
Warning: The RIP process will be deleted. Continue?[Y/N]y

Step 3 Configure OSPF.
Assign the value 10.0.1.1 (as used on logical interface loopback 0 for simplicity)
as the router ID. Use OSPF process 1 (the default process), and specify
network segments 10.0.1.0/24, 10.0.12.0/24, and 10.0.13.0/24 as part of
OSPF area 0.
[R1]ospf 1 router-id 10.0.1.1
[R1-ospf-1]area 0
[R1-ospf-1-area-0.0.0.0]network 10.0.1.0 0.0.0.255
[R1-ospf-1-area-0.0.0.0]network 10.0.13.0 0.0.0.255
[R1-ospf-1-area-0.0.0.0]network 10.0.12.0 0.0.0.255

Different process IDs will generate multiple link state databases, therefore
ensure that all routers use the same OSPF process ID. The wildcard mask
must be specified as part of the network command.
Manually assign the value 10.0.2.2 as the router ID. Use OSPF process 1, and
advertise network segments 10.0.12.0/24 and 10.0.2.0/24 into OSPF area 0.
[R2]ospf 1 router-id 10.0.2.2
[R2-ospf-1]area 0
[R2-ospf-1-area-0.0.0.0]network 10.0.2.0 0.0.0.255
[R2-ospf-1-area-0.0.0.0]network 10.0.12.0 0.0.0.255

M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 4 Routing Configuration

Page94 HUAWEI TECHNOLOGIES HC Series



output omitted
Nov 30 2013 09:41:39+00:00 R2 %%01OSPF/4/NBR_CHANGE_E(l)[5]:Neighbor changes event:
neighbor status changed. (ProcessId=1, NeighborAddress=10.0.12.1,
NeighborEvent=LoadingDone, NeighborPreviousState=Loading, NeighborCurrentState=Full)

Adjacency is attained when NeighborCurrentState=Full. For R3, Manually
assign the value 10.0.3.3 as the router ID. Use OSPF process 1, and advertise
network segments 10.0.3.0/24 and 10.0.13.0/24 into OSPF area 0.
[R3]ospf 1 router-id 10.0.3.3
[R3-ospf-1]area 0
[R3-ospf-1-area-0.0.0.0]network 10.0.3.0 0.0.0.255
[R3-ospf-1-area-0.0.0.0]network 10.0.13.0 0.0.0.255
output omitted
Nov 30 2013 16:05:34+00:00 R3 %%01OSPF/4/NBR_CHANGE_E(l)[5]:Neighbor changes event:
neighbor status changed. (ProcessId=1, NeighborAddress=10.0.13.1,
NeighborEvent=LoadingDone, NeighborPreviousState=Loading, NeighborCurrentState=Full)

Step 4 Verify the OSPF configuration.
After OSPF route convergence is complete, view routing tables of R1, R2, and
R3.
<R1>display ip routing-table
Route Flags: R - relay, D - download to fib
----------------------------------------------------------------------------
Routing Tables: Public
Destinations : 15 Routes : 15

Destination/Mask Proto Pre Cost Flags NextHop Interface

10.0.1.0/24 Direct 0 0 D 10.0.1.1 LoopBack0
10.0.1.1/32 Direct 0 0 D 127.0.0.1 LoopBack0
10.0.1.255/32 Direct 0 0 D 127.0.0.1 LoopBack0
10.0.2.2/32 OSPF 10 1 D 10.0.12.2 GigabitEthernet0/0/1
10.0.3.3/32 OSPF 10 1 D 10.0.13.3 GigabitEthernet0/0/0
10.0.12.0/24 Direct 0 0 D 10.0.12.1 GigabitEthernet0/0/1
10.0.12.1/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/1
10.0.12.255/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/1
10.0.13.0/24 Direct 0 0 D 10.0.13.1 GigabitEthernet0/0/0
10.0.13.1/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/0
M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 4 Routing Configuration

HC Series HUAWEI TECHNOLOGIES Page95

10.0.13.255/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/0
127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0
127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
127.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
255.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0

<R2>display ip routing-table
Route Flags: R - relay, D - download to fib
----------------------------------------------------------------------------
Routing Tables: Public
Destinations : 13 Routes : 13

Destination/Mask Proto Pre Cost Flags NextHop Interface

10.0.1.1/32 OSPF 10 1 D 10.0.12.1 GigabitEthernet0/0/1
10.0.2.0/24 Direct 0 0 D 10.0.2.2 LoopBack0
10.0.2.2/32 Direct 0 0 D 127.0.0.1 LoopBack0
10.0.2.255/32 Direct 0 0 D 127.0.0.1 LoopBack0
10.0.3.3/32 OSPF 10 2 D 10.0.12.1 GigabitEthernet0/0/1
10.0.12.0/24 Direct 0 0 D 10.0.12.2 GigabitEthernet0/0/1
10.0.12.2/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/1
10.0.12.255/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/1
10.0.13.0/24 OSPF 10 2 D 10.0.12.1 GigabitEthernet0/0/1
127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0
127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
127.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
255.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0

<R3>display ip routing-table
Route Flags: R - relay, D - download to fib
----------------------------------------------------------------------------
Routing Tables: Public
Destinations : 16 Routes : 16

Destination/Mask Proto Pre Cost Flags NextHop Interface

10.0.1.1/32 OSPF 10 1 D 10.0.13.1 GigabitEthernet0/0/0
10.0.2.2/32 OSPF 10 2 D 10.0.13.1 GigabitEthernet0/0/0
10.0.3.0/24 Direct 0 0 D 10.0.3.3 LoopBack0
10.0.3.3/32 Direct 0 0 D 127.0.0.1 LoopBack0
10.0.3.255/32 Direct 0 0 D 127.0.0.1 LoopBack0
10.0.12.0/24 OSPF 10 2 D 10.0.13.1 GigabitEthernet0/0/0
10.0.13.0/24 Direct 0 0 D 10.0.13.3 GigabitEthernet0/0/0
M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 4 Routing Configuration

Page96 HUAWEI TECHNOLOGIES HC Series

10.0.13.3/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/0
10.0.13.255/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/0
127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0
127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
127.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
172.16.0.0/24 Direct 0 0 D 172.16.0.1 LoopBack2
172.16.0.1/32 Direct 0 0 D 127.0.0.1 LoopBack2
172.16.0.255/32 Direct 0 0 D 127.0.0.1 LoopBack2
255.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0

Test network connectivity between R2 and R1 at 10.0.1.1 and between R2 and
R3 at 10.0.3.3.
<R2>ping 10.0.1.1
PING 10.0.1.1: 56 data bytes, press CTRL_C to break
Reply from 10.0.1.1: bytes=56 Sequence=1 ttl=255 time=37 ms
Reply from 10.0.1.1: bytes=56 Sequence=2 ttl=255 time=42 ms
Reply from 10.0.1.1: bytes=56 Sequence=3 ttl=255 time=42 ms
Reply from 10.0.1.1: bytes=56 Sequence=4 ttl=255 time=45 ms
Reply from 10.0.1.1: bytes=56 Sequence=5 ttl=255 time=42 ms

--- 10.0.1.1 ping statistics ---
5 packet(s) transmitted
5 packet(s) received
0.00% packet loss
round-trip min/avg/max = 37/41/45 ms

<R2>ping 10.0.3.3
PING 10.0.3.3: 56 data bytes, press CTRL_C to break
Reply from 10.0.3.3: bytes=56 Sequence=1 ttl=254 time=37 ms
Reply from 10.0.3.3: bytes=56 Sequence=2 ttl=254 time=42 ms
Reply from 10.0.3.3: bytes=56 Sequence=3 ttl=254 time=42 ms
Reply from 10.0.3.3: bytes=56 Sequence=4 ttl=254 time=42 ms
Reply from 10.0.3.3: bytes=56 Sequence=5 ttl=254 time=42 ms

--- 10.0.3.3 ping statistics ---
5 packet(s) transmitted
5 packet(s) received
0.00% packet loss
round-trip min/avg/max = 37/41/42 ms


M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 4 Routing Configuration

HC Series HUAWEI TECHNOLOGIES Page97

Run the display ospf peer command to view the OSPF neighbor status.
<R1>display ospf peer

OSPF Process 1 with Router ID 10.0.1.1
Neighbors

Area 0.0.0.0 interface 10.0.12.1(GigabitEthernet0/0/1)'s neighbors
Router ID: 10.0.2.2 Address: 10.0.12.2
State: Full Mode:Nbr is Master Priority: 1
DR: 10.0.12.1 BDR: 10.0.12.2 MTU: 0
Dead timer due in 32 sec
Retrans timer interval: 5
Neighbor is up for 00:47:59
Authentication Sequence: [ 0 ]

Neighbors

Area 0.0.0.0 interface 10.0.13.1(GigabitEthernet0/0/0)'s neighbors
Router ID: 10.0.3.3 Address: 10.0.13.3
State: Full Mode:Nbr is Master Priority: 1
DR: 10.0.13.1 BDR: 10.0.13.3 MTU: 0
Dead timer due in 34 sec
Retrans timer interval: 5
Neighbor is up for 00:41:44
Authentication Sequence: [ 0 ]

The display ospf peer command displays detailed information about any
peering neighbors. In the example given, the link 10.0.13.1 of R1 shows to be
the DR. The DR election is non pre-emptive, meaning that the link of R3 will
not take over the role of DR from R1 unless the OSPF process is reset.
The display ospf peer brief command can also be used to display a
condensed version of the OSPF peer information.
<R1>display ospf peer brief

OSPF Process 1 with Router ID 10.0.1.1
Peer Statistic Information
----------------------------------------------------------------------------
Area Id Interface Neighbor id State
0.0.0.0 GigabitEthernet0/0/0 10.0.3.3 Full
0.0.0.0 GigabitEthernet0/0/1 10.0.2.2 Full
----------------------------------------------------------------------------
M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 4 Routing Configuration

Page98 HUAWEI TECHNOLOGIES HC Series

<R2>display ospf peer brief

OSPF Process 1 with Router ID 10.0.2.2
Peer Statistic Information
----------------------------------------------------------------------------
Area Id Interface Neighbor id State
0.0.0.0 GigabitEthernet0/0/1 10.0.1.1 Full
----------------------------------------------------------------------------

<R3>display ospf peer brief
OSPF Process 1 with Router ID 10.0.3.3
Peer Statistic Information
----------------------------------------------------------------------------
Area Id Interface Neighbor id State
0.0.0.0 GigabitEthernet0/0/0 10.0.1.1 Full
----------------------------------------------------------------------------
Step 5 Change the OSPF hello interval and dead interval.
Run the display ospf interface GigabitEthernet 0/0/0 command on R1 to
view the default OSPF hello interval and dead interval.
<R1>display ospf interface GigabitEthernet 0/0/0

OSPF Process 1 with Router ID 10.0.1.1
Interfaces


Interface: 10.0.13.1 (GigabitEthernet0/0/0)
Cost: 1 State: DR Type: Broadcast MTU: 1500
Priority: 1
Designated Router: 10.0.13.1
Backup Designated Router: 10.0.13.3
Timers: Hello 10 , Dead 40 , Poll 120 , Retransmit 5 , Transmit Delay 1

Run the ospf timer command to change the OSPF hello interval and dead
interval on GE0/0/0 of R1 to 15s and 60s respectively.
[R1]interface GigabitEthernet 0/0/0
[R1-GigabitEthernet0/0/0]ospf timer hello 15
[R1-GigabitEthernet0/0/0]ospf timer dead 60
Nov 30 2013 16:58:39+00:00 R1 %%01OSPF/3/NBR_DOWN_REASON(l)[1]:Neighbor state
leaves full or changed to Down. (ProcessId=1, NeighborRouterId=10.0.3.3,
NeighborAreaId=0,
M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 4 Routing Configuration

HC Series HUAWEI TECHNOLOGIES Page99

NeighborInterface=GigabitEthernet0/0/0,NeighborDownImmediate reason=Neighbor
Down Due to Inactivity, NeighborDownPrimeReason=Interface Parameter Mismatch,
NeighborChangeTime=2013-11-30 16:58:39)

<R1>display ospf interface GigabitEthernet 0/0/0

OSPF Process 1 with Router ID 10.0.1.1
Interfaces


Interface: 10.0.13.1 (GigabitEthernet0/0/0)
Cost: 1 State: DR Type: Broadcast MTU: 1500
Priority: 1
Designated Router: 10.0.13.1
Backup Designated Router: 10.0.13.3
Timers: Hello 15 , Dead 60 , Poll 120 , Retransmit 5 , Transmit Delay 1

Check the OSPF neighbor status on R1.
<R1>display ospf peer brief

OSPF Process 1 with Router ID 10.0.1.1
Peer Statistic Information
----------------------------------------------------------------------------
Area Id Interface Neighbor id State
0.0.0.0 GigabitEthernet0/0/1 10.0.2.2 Full
----------------------------------------------------------------------------

The preceding information shows that R1 has only one neighbor, R2. Since the
OSPF hello intervals and dead intervals on R1 and R3 are different, R1 and R3
will fail to establish an OSPF neighbor relationship.
Run the ospf timer command to change the OSPF hello interval and dead
interval on GE0/0/0 of R3 to 15s and 60s respectively.
[R3]interface GigabitEthernet 0/0/0
[R3-GigabitEthernet0/0/0]ospf timer hello 15
[R3-GigabitEthernet0/0/0]ospf timer dead 60
output omitted
Nov 30 2013 17:03:33+00:00 R3 %%01OSPF/4/NBR_CHANGE_E(l)[4]:Neighbor changes
event: neighbor status changed. (ProcessId=1, NeighborAddress=10.0.13.1,
NeighborEvent=LoadingDone, NeighborPreviousState=Loading,
NeighborCurrentState=Full)

M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 4 Routing Configuration

Page100 HUAWEI TECHNOLOGIES HC Series

<R3>display ospf interface GigabitEthernet 0/0/0

OSPF Process 1 with Router ID 10.0.3.3
Interfaces

Interface: 10.0.13.3 (GigabitEthernet0/0/0)
Cost: 1 State: DR Type: Broadcast MTU: 1500
Priority: 1
Designated Router: 10.0.13.3
Backup Designated Router: 10.0.13.1
Timers: Hello 15 , Dead 60 , Poll 120 , Retransmit 5 , Transmit Delay 1

Check the OSPF neighbor status on R1 again.
<R1>display ospf peer brief
OSPF Process 1 with Router ID 10.0.1.1
Peer Statistic Information
----------------------------------------------------------------------------
Area Id Interface Neighbor id State
0.0.0.0 GigabitEthernet0/0/0 10.0.3.3 Full
0.0.0.0 GigabitEthernet0/0/1 10.0.2.2 Full
----------------------------------------------------------------------------

Step 6 Advertise default routes in OSPF.
Configure OSPF to advertise default routes on R3.
[R3]ip route-static 0.0.0.0 0.0.0.0 LoopBack 2
[R3]ospf 1
[R3-ospf-1]default-route-advertise

View routing tables of R1 and R2. You can see that R1 and R2 have learned
the default routes advertised by R3.
<R1>display ip routing-table
Route Flags: R - relay, D - download to fib
----------------------------------------------------------------------------
Routing Tables: Public
Destinations : 16 Routes : 16

Destination/Mask Proto Pre Cost Flags NextHop Interface

M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 4 Routing Configuration

HC Series HUAWEI TECHNOLOGIES Page101

0.0.0.0/0 O_ASE 150 1 D 10.0.13.3 GigabitEthernet0/0/0
10.0.1.0/24 Direct 0 0 D 10.0.1.1 LoopBack0
10.0.1.1/32 Direct 0 0 D 127.0.0.1 LoopBack0
10.0.1.255/32 Direct 0 0 D 127.0.0.1 LoopBack0
10.0.2.2/32 OSPF 10 1 D 10.0.12.2 GigabitEthernet0/0/1
10.0.3.3/32 OSPF 10 1 D 10.0.13.3 GigabitEthernet0/0/0
10.0.12.0/24 Direct 0 0 D 10.0.12.1 GigabitEthernet0/0/1
10.0.12.1/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/1
10.0.12.255/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/1
10.0.13.0/24 Direct 0 0 D 10.0.13.1 GigabitEthernet0/0/0
10.0.13.1/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/0
10.0.13.255/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/0
127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0
127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
127.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
255.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0


<R2>display ip routing-table
Route Flags: R - relay, D - download to fib
----------------------------------------------------------------------------
Routing Tables: Public
Destinations : 14 Routes : 14

Destination/Mask Proto Pre Cost Flags NextHop Interface

0.0.0.0/0 O_ASE 150 1 D 10.0.12.1 GigabitEthernet0/0/1
10.0.1.1/32 OSPF1 0 1 D 10.0.12.1 GigabitEthernet0/0/1
10.0.2.0/24 Direct 0 0 D 10.0.2.2 LoopBack0
10.0.2.2/32 Direct 0 0 D 127.0.0.1 LoopBack0
10.0.2.255/32 Direct 0 0 D 127.0.0.1 LoopBack0
10.0.3.3/32 OSPF 10 2 D 10.0.12.1 GigabitEthernet0/0/1
10.0.12.0/24 Direct 0 0 D 10.0.12.2 GigabitEthernet0/0/1
10.0.12.2/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/1
10.0.12.255/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/1
10.0.13.0/24 OSPF 10 2 D 10.0.12.1 GigabitEthernet0/0/1
127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0
127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
127.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
255.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0



M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 4 Routing Configuration

Page102 HUAWEI TECHNOLOGIES HC Series


<R3>display ip routing-table
Route Flags: R - relay, D - download to fib
----------------------------------------------------------------------------
Routing Tables: Public
Destinations : 17 Routes : 17

Destination/Mask Proto Pre Cost Flags NextHop Interface

0.0.0.0/0 Static 60 0 D 172.16.0.1 LoopBack2
10.0.1.1/32 OSPF 10 1 D 10.0.13.1 GigabitEthernet0/0/0
10.0.2.2/32 OSPF 10 2 D 10.0.13.1 GigabitEthernet0/0/0
10.0.3.0/24 Direct 0 0 D 10.0.3.3 LoopBack0
10.0.3.3/32 Direct 0 0 D 127.0.0.1 LoopBack0
10.0.3.255/32 Direct 0 0 D 127.0.0.1 LoopBack0
10.0.12.0/24 OSPF 10 2 D 10.0.13.1 GigabitEthernet0/0/0
10.0.13.0/24 Direct 0 0 D 10.0.13.3 GigabitEthernet0/0/0
10.0.13.3/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/0
10.0.13.255/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/0
127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0
127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
127.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
172.16.0.0/24 Direct 0 0 D 172.16.0.1 LoopBack2
172.16.0.1/32 Direct 0 0 D 127.0.0.1 LoopBack2
172.16.0.255/32 Direct 0 0 D 127.0.0.1 LoopBack2
255.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0

Run the ping command to test connectivity between R2 and Loopback2 at
172.16.0.1.
<R2>ping 172.16.0.1
PING 172.16.0.1: 56 data bytes, press CTRL_C to break
Reply from 172.16.0.1: bytes=56 Sequence=1 ttl=254 time=47 ms
Reply from 172.16.0.1: bytes=56 Sequence=2 ttl=254 time=37 ms
Reply from 172.16.0.1: bytes=56 Sequence=3 ttl=254 time=37 ms
Reply from 172.16.0.1: bytes=56 Sequence=4 ttl=254 time=37 ms
Reply from 172.16.0.1: bytes=56 Sequence=5 ttl=254 time=37 ms

--- 172.16.0.1 ping statistics ---
5 packet(s) transmitted
5 packet(s) received
0.00% packet loss
round-trip min/avg/max = 37/39/47 ms
M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 4 Routing Configuration

HC Series HUAWEI TECHNOLOGIES Page103


Step 7 Control OSPF DR or BDR election.
Run the display ospf peer command to view the DR and BDR of R1 and R3.
<R1>display ospf peer 10.0.3.3

OSPF Process 1 with Router ID 10.0.1.1
Neighbors

Area 0.0.0.0 interface 10.0.13.1(GigabitEthernet0/0/0)'s neighbors
Router ID: 10.0.3.3 Address: 10.0.13.3
State: Full Mode:Nbr is Master Priority: 1
DR: 10.0.13.3 BDR: 10.0.13.1 MTU: 0
Dead timer due in 49 sec
Retrans timer interval: 5
Neighbor is up for 00:17:40
Authentication Sequence: [ 0 ]

The preceding information shows that R3 is the DR and R1 is the BDR. This is
because R3's router ID 10.0.3.3 is greater than R1's router ID 10.0.1.1. R1 and
R3 use the default priority of 1, so their router IDs are used for DR or BDR
election.
Run the ospf dr-priority command to change DR priorities of R1 and R3.
[R1]interface GigabitEthernet 0/0/0
[R1-GigabitEthernet0/0/0]ospf dr-priority 200

[R3]interface GigabitEthernet 0/0/0
[R3-GigabitEthernet0/0/0]ospf dr-priority 100

A DR or BDR is elected in non-preemption mode, by default. After router
priorities are changed, a DR is not re-elected, so you must reset the OSPF
neighbor relationship between R1 and R3.
Shut down and re-enable Gigabit Ethernet 0/0/0 interfaces on R1 and R3 to
reset the OSPF neighbor relationship between R1 and R3.
[R3]interface GigabitEthernet0/0/0
[R3-GigabitEthernet0/0/0]shutdown

[R1]interface GigabitEthernet0/0/0
[R1-GigabitEthernet0/0/0]shutdown
M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 4 Routing Configuration

Page104 HUAWEI TECHNOLOGIES HC Series


[R1-GigabitEthernet0/0/0]undo shutdown

[R3-GigabitEthernet0/0/0]undo shutdown

Run the display ospf peer command to view the DR and BDR of R1 and R3.
[R1]display ospf peer 10.0.3.3

OSPF Process 1 with Router ID 10.0.1.1
Neighbors

Area 0.0.0.0 interface 10.0.13.1(GigabitEthernet0/0/0)'s neighbors
Router ID: 10.0.3.3 Address: 10.0.13.3
State: Full Mode:Nbr is Master Priority: 100
DR: 10.0.13.1 BDR: 10.0.13.3 MTU: 0
Dead timer due in 52 sec
Retrans timer interval: 5
Neighbor is up for 00:00:25
Authentication Sequence: [ 0 ]

According to the preceding information, R1's priority is higher than R3's priority,
so R1 becomes DR and R3 becomes the BDR.
Final Configuration
<R1>display current-configuration
[V200R003C00SPC200]
#
sysname R1
#
interface GigabitEthernet0/0/0
ip address 10.0.13.1 255.255.255.0
ospf dr-priority 200
ospf timer hello 15
#
interface GigabitEthernet0/0/1
ip address 10.0.12.1 255.255.255.0
#
interface LoopBack0
ip address 10.0.1.1 255.255.255.0
#
M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 4 Routing Configuration

HC Series HUAWEI TECHNOLOGIES Page105

ospf 1 router-id 10.0.1.1
area 0.0.0.0
network 10.0.1.0 0.0.0.255
network 10.0.12.0 0.0.0.255
network 10.0.13.0 0.0.0.255
#
user-interface con 0
authentication-mode password
set authentication password cipher %$%$+L'YR&IZt'4,)>-*#lH",}%K-oJ_M9+'lOU~bD
(\WTqB}%N,%$%$
user-interface vty 0 4
#
return


<R2>display current-configuration
[V200R003C00SPC200]
#
sysname R2
#
interface GigabitEthernet0/0/1
ip address 10.0.12.2 255.255.255.0
#
interface LoopBack0
ip address 10.0.2.2 255.255.255.0
#
ospf 1 router-id 10.0.2.2
area 0.0.0.0
network 10.0.2.0 0.0.0.255
network 10.0.12.0 0.0.0.255
#
user-interface con 0
authentication-mode password
set authentication password cipher %$%$1=cd%b%/O%Id-8X:by1N,+s}'4wD6TvO<I|/pd#
#44C@+s#,%$%$
user-interface vty 0 4
#
return





M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 4 Routing Configuration

Page106 HUAWEI TECHNOLOGIES HC Series

<R3>display current-configuration
[V200R003C00SPC200]
#
sysname R3
#
interface GigabitEthernet0/0/0
ip address 10.0.13.3 255.255.255.0
ospf dr-priority 100
ospf timer hello 15
#
interface LoopBack0
ip address 10.0.3.3 255.255.255.0
#
interface LoopBack2
ip address 172.16.0.1 255.255.255.0
#
ospf 1 router-id 10.0.3.3
default-route-advertise
area 0.0.0.0
network 10.0.3.0 0.0.0.255
network 10.0.13.0 0.0.0.255
#
ip route-static 0.0.0.0 0.0.0.0 LoopBack2
#
user-interface con 0
authentication-mode password
set authentication password cipher %$%$ksXDMg7Ry6yUU:63:DQ),#/sQg"@*S\U#.s.bHW
xQ,y%#/v,%$%$
user-interface vty 0 4
#
return

M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 5 FTP and DHCP

HC Series HUAWEI TECHNOLOGIES Page107

Chapter 5 FTP and DHCP
Lab 5-1 Configuring FTP Services
Learning Objectives
As a result of this lab section, you should achieve the following tasks:
Establishment of the FTP service.
Configuration of FTP server parameters.
Successful file transfer from an FTP server.
Topology

Figure 5.1 FTP topology
Scenario
As a network administrator of a company, you have been tasked with
implementing FTP services on the network. You need to implement the FTP
service on a router assigned to be an FTP server. The router should allow
clients to successfully establish a TCP session to the FTP application and
transfer files.

M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:
h
t
t
p
:/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 5 FTP and DHCP

Page108 HUAWEI TECHNOLOGIES HC Series

Tasks
Step 1 Preparing the environment.
If you are starting this section with a non-configured device, begin here and
then move to step 2. For those continuing from previous labs, begin at step 2.

<Huawei>system-view
Enter system view, return user view with Ctrl+Z.
[Huawei]sysname R1
[R1]interface GigabitEthernet 0/0/1
[R1-GigabitEthernet0/0/1]ip address 10.0.12.1 24

<Huawei>system-view
Enter system view, return user view with Ctrl+Z.
[Huawei]sysname R2
[R2]interface GigabitEthernet 0/0/1
[R2-GigabitEthernet0/0/1]ip address 10.0.12.2 24

Verify that R1 can reach R2, and vice versa..
[R1]ping 10.0.12.2
PING 10.0.12.2: 56 data bytes, press CTRL_C to break
Reply from 10.0.12.2: bytes=56 Sequence=1 ttl=255 time=10 ms
Reply from 10.0.12.2: bytes=56 Sequence=2 ttl=255 time=1 ms
Reply from 10.0.12.2: bytes=56 Sequence=3 ttl=255 time=1 ms
Reply from 10.0.12.2: bytes=56 Sequence=4 ttl=255 time=10 ms
Reply from 10.0.12.2: bytes=56 Sequence=5 ttl=255 time=1 ms

--- 10.0.12.2 ping statistics ---
5 packet(s) transmitted
5 packet(s) received
0.00% packet loss
round-trip min/avg/max = 1/4/10 ms

Step 2 Enable the FTP service on the router.
The FTP service is disabled by default on the router. It must be enabled before
FTP can be used. Configure an FTP server using R1 with R2 as the client. The
same steps can be reversed to enable R2 to also act as an FTP server.
M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 5 FTP and DHCP

HC Series HUAWEI TECHNOLOGIES Page109

[R1]ftp server enable
Info: Succeeded in starting the FTP server
[R1]set default ftp-directory sd1:

Configure user authorization for FTP users to access the server. Unauthorized
users will not be able to access the FTP server, reducing security risks.
[R1]aaa
[R1-aaa]local-user huawei password cipher huawei
Info: Add a new user.
[R1-aaa]local-user huawei service-type ftp
[R1-aaa]local-user huawei privilege level 15
[R1-aaa]local-user huawei ftp-directory sd1:

[R1]display ftp-server
FTP server is running
Max user number 5
User count 0
Timeout value(in minute) 30
Listening port 21
Acl number 0
FTP server's source address 0.0.0.0

The FTP server is running on R1 and listens on TCP port 21 by default.
Step 3 Establish an FTP client connection
Establish a connection to the FTP Server from R2.
<R2>ftp 10.0.12.1
Trying 10.0.12.1 ...
Press CTRL+K to abort
Connected to 10.0.12.1.
220 FTP service ready.
User(10.0.12.1:(none)):huawei
331 Password required for huawei.
Enter password:
230 User logged in.

[R2-ftp]

Following entry of the correct user name and password, the FTP server can be
successfully logged into.
M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 5 FTP and DHCP

Page110 HUAWEI TECHNOLOGIES HC Series

Run the dir command before downloading a file or after uploading a file to view
the detailed information of the file.
[R2-ftp]dir
200 Port command okay.
150 Opening ASCII mode data connection for *.
-rwxrwxrwx 1 noone nogroup 286620 Mar 14 09:22 sacrule.dat
-rwxrwxrwx 1 noone nogroup 512000 Nov 28 14:39 mon_file.txt
-rwxrwxrwx 1 noone nogroup 48128 Oct 10 2011 ar2220_v200r001sph001.pat
-rwxrwxrwx 1 noone nogroup 120 Dec 28 2012 iascfg.zip
-rwxrwxrwx 1 noone nogroup 699 Nov 28 17:52 vrpcfg.zip
-rwxrwxrwx 1 noone nogroup 93871872 Mar 14 09:13 ar2220-v200r003c00spc200.cc
-rwxrwxrwx 1 noone nogroup 512000 Nov 28 14:40 mon_lpu_file.txt
226 Transfer complete.
FTP: 836 byte(s) received in 0.976 second(s) 856.55byte(s)/sec.

Set the transfer mode for the files to be transferred.

[R2-ftp]binary
200 Type set to I.

Retrieve a file from the FTP server. Note: If the vrpcfg.zip file is not present in
the sd1: directory of R1, use the save command on R1 to create it.

[R2-ftp]get vrpcfg.zip vrpnew.zip
200 Port command okay.
150 Opening BINARY mode data connection for vrpcfg.zip.
226 Transfer complete.
FTP: 120 byte(s) received in 0.678 second(s) 176.99byte(s)/sec.

After downloading the file from FTP server, use the bye command to close the
connection

[R2-ftp]bye
221 Server closing.

<R2>dir
Directory of sd1:/

Idx Attr Size(Byte) Date Time(LMT) FileName
0 -rw- 286,620 Mar 14 2013 09:05:14 sacrule.dat
1 -rw- 512,000 Nov 30 2013 03:47:04 mon_file.txt
3 -rw- 48,128 Oct 10 2011 12:30:26 ar2220_v200r001sph001.pat
M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 5 FTP and DHCP

HC Series HUAWEI TECHNOLOGIES Page111

4 -rw- 120 Dec 31 2012 04:20:48 iascfg.zip
5 -rw- 856 Nov 30 2013 03:40:56 vrpcfg.zip
6 -rw- 93,871,872 Mar 14 2013 08:59:46 ar2220-v200r003c00spc200.cc
7 -rw- 512,000 Nov 30 2013 03:48:06 mon_lpu_file.txt
8 -rw- 699 Dec 02 2013 09:03:16 vrpnew.zip

A file can be uploaded to the FTP server by using the command put, for which
a new file name can also be assigned.
[R2-ftp]put vrpnew.zip vrpnew2.zip
200 Port command okay.
150 Opening BINARY mode data connection for vrpnew2.zip.
226 Transfer complete.
FTP: 120 byte(s) sent in 0.443 second(s) 270.88byte(s)/sec.

After uploading the file, check for the presence of the file on FTP server.
<R1>dir
Directory of sd1:/

Idx Attr Size(Byte) Date Time(LMT) FileName
0 -rw- 286,620 Mar 14 2013 09:22:20 sacrule.dat
1 -rw- 512,000 Nov 28 2013 14:39:16 mon_file.txt
2 -rw- 1,738,816 Feb 17 2013 12:05:36 web.zip
3 -rw- 48,128 Oct 10 2011 14:16:56 ar2220_v200r001sph001.pat
4 -rw- 120 Dec 28 2012 10:09:50 iascfg.zip
5 -rw- 699 Nov 28 2013 17:52:38 vrpcfg.zip
6 -rw- 93,871,872 Mar 14 2013 09:13:26 ar2220-v200r003c00spc200.cc
7 -rw- 512,000 Nov 28 2013 14:40:20 mon_lpu_file.txt
8 -rw- 699 Dec 02 2013 15:44:16 vrpnew2.zip

Remove the created vrpnew.zip and vrpnew2.zip files on R1 and R2.
<R1>delete sd1:/vrpnew2.zip
Delete sd1:/vrpnew2.zip? (y/n)[n]:y
Info: Deleting file sd1:/vrpnew2.zip...succeed.

<R2>delete sd1:/vrpnew.zip
Delete sd1:/vrpnew.zip? (y/n)[n]:y
Info: Deleting file sd1:/vrpnew.zip...succeed.

Note: Please take exteme care when deleting the configuration files so to
ensure that the entire sd1:/ directory of R1 and R2 is not erased.
M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 5 FTP and DHCP

Page112 HUAWEI TECHNOLOGIES HC Series

Final Configuration
<R1>display current-configuration
[V200R003C00SPC200]
#
sysname R1
ftp server enable
set default ftp-directory sd1:
#
aaa
authentication-scheme default
authorization-scheme default
accounting-scheme default
domain default
domain default_admin
local-user admin password cipher %$%$=i~>Xp&aY+*2cEVcS-A23Uwe%$%$
local-user admin service-type http
local-user huawei password cipher %$%$f+~&ZkCn]NUX7m.t;tF9R48s%$%$
local-user huawei privilege level 15
local-user huawei ftp-directory sd1:
local-user huawei service-type ftp
#
interface GigabitEthernet0/0/1
ip address 10.0.12.1 255.255.255.0
#
user-interface con 0
authentication-mode password
set authentication password cipher %$%$+L'YR&IZt'4,)>-*#lH",}%K-oJ_M9+'lOU~bD
(\WTqB}%N,%$%$
user-interface vty 0 4
#
return

<R2>display current-configuration
[V200R003C00SPC200]
#
sysname R2
ftp server enable
set default ftp-directory sd1:
#
aaa
authentication-scheme default
M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 5 FTP and DHCP

HC Series HUAWEI TECHNOLOGIES Page113

authorization-scheme default
accounting-scheme default
domain default
domain default_admin
local-user admin password cipher %$%$=i~>Xp&aY+*2cEVcS-A23Uwe%$%$
local-user admin service-type http
local-user huawei password cipher %$%$<;qM3D/O;ZLqy/"&6wEESdg$%$%$
local-user huawei privilege level 15
local-user huawei ftp-directory sd1:
local-user huawei service-type ftp
#
interface GigabitEthernet0/0/1
ip address 10.0.12.2 255.255.255.0
#
user-interface con 0
authentication-mode password
set authentication password cipher %$%$1=cd%b%/O%Id-8X:by1N,+s}'4wD6TvO<I|/pd#
#44C@+s#,%$%$
user-interface vty 0 4
#
return


M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 5 FTP and DHCP

Page114 HUAWEI TECHNOLOGIES HC Series

Lab 5-2 Implementing DHCP
Learning Objectives
As a result of this lab section, you should achieve the following tasks:
Configuration of a global DHCP pool.
Configuration of an interface based DHCP pool.
Enable DHCP discovery and IP allocation for switch interfaces.
Method of global address pool configuration.
Method of interface address pool configuration.
Topology

Figure 5.2 DHCP topology
Scenario
As the administrator of an enterprise you have been tasked with implementing
DHCP application services within the network. The gateway router in the
company network is to be configured as a DHCP server. IP addressing from an
address pool are to be offered by the gateway(s) (R1 and R3) to respective
access layer devices.

M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:
h
t
t
p
:/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 5 FTP and DHCP

HC Series HUAWEI TECHNOLOGIES Page115

Tasks
Step 1 Preparing the environment
If you are starting this section with a non-configured device, begin here and
then move to step 3. For those continuing from previous labs, begin at step 2.
Establish the addressing for the lab and temporarily shut down the interfaces
Gigabit Ethernet 0/0/2 of R1 and Gigabit Ethernet 0/0/1 of R3.
<Huawei>system-view
Enter system view, return user view with Ctrl+Z.
[Huawei]sysname R1
[R1]interface GigabitEthernet 0/0/1
[R1-GigabitEthernet0/0/1]ip address 10.0.12.1 24
[R1-GigabitEthernet0/0/1]quit

<Huawei>system-view
Enter system view, return user view with Ctrl+Z.
[Huawei]sysname R3
[R3]interface GigabitEthernet 0/0/1
[R3-GigabitEthernet0/0/1]ip address 10.0.12.3 24
[R3-GigabitEthernet0/0/1]shutdown
[R3-GigabitEthernet0/0/1]quit
[R3]interface GigabitEthernet 0/0/2
[R3-GigabitEthernet0/0/2]ip address 10.0.23.3 24

<Quidway>system-view
Enter system view, return user view with Ctrl+Z.
[Quidway]sysname S1

<Quidway>system-view
Enter system view, return user view with Ctrl+Z.
[Quidway]sysname S2



M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 5 FTP and DHCP

Page116 HUAWEI TECHNOLOGIES HC Series

Step 2 Cleaning up the previous configuration
Re-enable to Gigabit Ethernet 0/0/2 interface on R3.

[R3]interface GigabitEthernet 0/0/2
[R3-GigabitEthernet0/0/2]undo shutdown

Step 3 Additional configuration
Disable the port interfaces between S1 and S2 as well as other interfaces to
prevent interference from other devices.

[S1]interface GigabitEthernet 0/0/9
[S1-GigabitEthernet0/0/9]shutdown
[S1-GigabitEthernet0/0/9]quit
[S1]interface GigabitEthernet 0/0/10
[S1-GigabitEthernet0/0/10]shutdown
[S1-GigabitEthernet0/0/10]quit
[S1]interface GigabitEthernet 0/0/13
[S1-GigabitEthernet0/0/13]shutdown
[S1-GigabitEthernet0/0/13]quit
[S1]interface GigabitEthernet 0/0/14
[S1-GigabitEthernet0/0/14]shutdown

[S2]interface GigabitEthernet 0/0/9
[S2-GigabitEthernet0/0/9]shutdown
[S2-GigabitEthernet0/0/9]quit
[S2]interface GigabitEthernet 0/0/10
[S2-GigabitEthernet0/0/10]shutdown
[S2-GigabitEthernet0/0/10]quit
[S2]interface GigabitEthernet 0/0/23
[S2-GigabitEthernet0/0/23]shutdown
[S2-GigabitEthernet0/0/23]quit
[S2]interface GigabitEthernet 0/0/24
[S2-GigabitEthernet0/0/24]shutdown

[R1]interface GigabitEthernet 0/0/2
[R1-GigabitEthernet0/0/2]ip address 10.0.23.1 24
[R1-GigabitEthernet0/0/2]shutdown



M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 5 FTP and DHCP

HC Series HUAWEI TECHNOLOGIES Page117

Verify that Gigabit Ethernet interfaces 0/0/9, 0/0/10, 0/0/13 and 0/0/14, have
been shut down on S1 and that Gigabit Ethernet interfaces 0/09, 0/0/10, 0/0/23
and 0/0/24 have been shut down on S2.

<S1>display interface brief
output omitted
Interface PHY Protocol InUti OutUti inErrors outErrors
GigabitEthernet0/0/1 up up 0.01% 0.01% 0 0
GigabitEthernet0/0/2 up up 0.01% 0.01% 0 0
GigabitEthernet0/0/3 down down 0% 0% 0 0
GigabitEthernet0/0/4 up up 0% 0.01% 0 0
GigabitEthernet0/0/5 up up 0% 0.01% 0 0
GigabitEthernet0/0/6 down down 0% 0% 0 0
GigabitEthernet0/0/7 down down 0% 0% 0 0
GigabitEthernet0/0/8 down down 0% 0% 0 0
GigabitEthernet0/0/9 *down down 0% 0% 0 0
GigabitEthernet0/0/10 *down down 0% 0% 0 0
GigabitEthernet0/0/11 down down 0% 0% 0 0
GigabitEthernet0/0/12 down down 0% 0% 0 0
GigabitEthernet0/0/13 *down down 0% 0% 0 0
GigabitEthernet0/0/14 *down down 0% 0% 0 0
output omitted

<S2>display interface brief
output omitted
GigabitEthernet0/0/9 *down down 0% 0% 0 0
GigabitEthernet0/0/10 *down down 0% 0% 0 0
GigabitEthernet0/0/11 up up 0.01% 0.01% 0 0
GigabitEthernet0/0/12 up up 0.01% 0.01% 0 0
GigabitEthernet0/0/13 up up 0% 0.01% 0 0
GigabitEthernet0/0/14 down down 0% 0% 0 0
GigabitEthernet0/0/15 down down 0% 0% 0 0
GigabitEthernet0/0/16 down down 0% 0% 0 0
GigabitEthernet0/0/17 down down 0% 0% 0 0
GigabitEthernet0/0/18 down down 0% 0% 0 0
GigabitEthernet0/0/19 down down 0% 0% 0 0
GigabitEthernet0/0/20 down down 0% 0% 0 0
GigabitEthernet0/0/21 down down 0% 0% 0 0
GigabitEthernet0/0/22 down down 0% 0% 0 0
GigabitEthernet0/0/23 *down down 0% 0% 0 0
GigabitEthernet0/0/24 *down down 0% 0% 0 0
output omitted

M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 5 FTP and DHCP

Page118 HUAWEI TECHNOLOGIES HC Series

Verify that only interface Gigabit Ethernet 0/0/2 is disabled on R1 and that only
interface Gigabit Ethernet 0/0/1 is disabled on R3.

<R1>display ip interface brief
output omitted
GigabitEthernet0/0/1 10.0.12.1/24 up up
GigabitEthernet0/0/2 10.0.23.1/24 *down down
output omitted

<R3>display ip interface brief
output omitted
GigabitEthernet0/0/1 10.0.12.3/24 *down down
GigabitEthernet0/0/2 10.0.23.3/24 up up
output omitted

Step 4 Enable the DHCP function.
The DHCP service is not enabled by default, enable the DHCP service on the
router(s).
[R1]dhcp enable

[R3]dhcp enable
Step 5 Create a global IP address pool
Create an address pool named pool1 for R1 and pool2 for R3. Configure
attributes for pool1 and pool2, including address range, egress gateway, and
IP address lease period.
[R1]ip pool pool1
Info: It's successful to create an IP address pool.
[R1-ip-pool-pool1]network 10.0.12.0 mask 24
[R1-ip-pool-pool1]gateway-list 10.0.12.1
[R1-ip-pool-pool1]lease day 1 hour 12
[R1]interface GigabitEthernet 0/0/1
[R1-GigabitEthernet0/0/1]dhcp select global

[R3]ip pool pool2
Info: It's successful to create an IP address pool.
[R3-ip-pool-pool2]network 10.0.23.0 mask 24
[R3-ip-pool-pool2]gateway-list 10.0.23.3
[R3-ip-pool-pool2]lease day 1 hour 12
M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 5 FTP and DHCP

HC Series HUAWEI TECHNOLOGIES Page119

[R3]interface GigabitEthernet 0/0/2
[R3-GigabitEthernet0/0/2]dhcp select global

Run the display ip pool name <name> command on the router to view the
assigned IP address pool configuration parameters.
<R1>display ip pool name pool1
Pool-name : pool1
Pool-No : 0
Lease : 1 Days 12 Hours 0 Minutes
Domain-name : -
DNS-server0 : -
NBNS-server0 : -
Netbios-type : -
Position : Local Status : Unlocked
Gateway-0 : 10.0.12.1
Mask : 255.255.255.0
VPN instance : --

----------------------------------------------------------------------------
Start End Total Used Idle(Expired) Conflict Disable
----------------------------------------------------------------------------
10.0.12.1 10.0.12.254 253 0 253(0) 0 0
----------------------------------------------------------------------------

Configure the default management interface for S1 to request an IP address
from the DHCP server (R1). Perform the same steps on S2 for R3.

[S1]dhcp enable
[S1]interface Vlanif 1
[S1-Vlanif1]ip address dhcp-alloc

<S1>display ip interface brief
output omitted
Interface IP Address/Mask Physical Protocol
MEth0/0/1 unassigned down down
NULL0 unassigned up up(s)
Vlanif1 10.0.12.254/24 up up





M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 5 FTP and DHCP

Page120 HUAWEI TECHNOLOGIES HC Series

Verify that this address was taken from the DHCP pool named pool1 on R1,
and for S2, from the DHCP pool named pool2 on R3.

<R1>display ip pool name pool1
Pool-name : pool1
Pool-No : 0
Lease : 1 Days 12 Hours 0 Minutes
Domain-name : -
DNS-server0 : -
NBNS-server0 : -
Netbios-type : -
Position : Local Status : Unlocked
Gateway-0 : 10.0.12.1
Mask : 255.255.255.0
VPN instance : --

----------------------------------------------------------------------------
Start End Total Used Idle(Expired) Conflict Disable
----------------------------------------------------------------------------
10.0.12.1 10.0.12.254 253 1 252(0) 0 0
----------------------------------------------------------------------------

<R3>display ip pool name pool2
Pool-name : pool2
Pool-No : 0
Lease : 1 Days 12 Hours 0 Minutes
Domain-name : -
DNS-server0 : -
NBNS-server0 : -
Netbios-type : -
Position : Local Status : Unlocked
Gateway-0 : 10.0.23.3
Mask : 255.255.255.0
VPN instance : --
----------------------------------------------------------------------------
Start End Total Used Idle(Expired) Conflict Disable
----------------------------------------------------------------------------
10.0.23.1 10.0.23.254 253 1 252(0) 0 0
----------------------------------------------------------------------------

Ensure that global pool configuration has been completed for both R1 and R3
before continuing!
M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 5 FTP and DHCP

HC Series HUAWEI TECHNOLOGIES Page121

Step 6 Create an interface based IP address pool
Disable the interface Gigabit Ethernet 0/0/1 R1. For R3 disable interface
Gigabit Ethernet 0/0/2.
[R1]interface GigabitEthernet 0/0/1
[R1-GigabitEthernet0/0/1]shutdown

[R3]interface GigabitEthernet 0/0/2
[R3-GigabitEthernet0/0/2]shutdown

Configure an interface address pool to allow the clients connected via Gigabit
Ethernet 0/0/2 of R1 to obtain IP addresses. Perform the same operation for
Gigabit Ethernet 0/0/1 of R3. Do not enable these interfaces, as we do not yet
wish to activate the DHCP service on the network.
[R1]interface GigabitEthernet 0/0/2
[R1-GigabitEthernet0/0/2]dhcp select interface

[R3]interface GigabitEthernet 0/0/1
[R3-GigabitEthernet0/0/1]dhcp select interface

Isolate addresses from the pool GigabitEthernet0/0/2 for R1, and the pool
GigabitEthernet0/0/1 for R3, for DNS services. Additionally, set the IP address
lease period for the interface address pool.
[R1-GigabitEthernet0/0/2]dhcp server dns-list 10.0.23.254
[R1-GigabitEthernet0/0/2]dhcp server excluded-ip-address 10.0.23.254
[R1-GigabitEthernet0/0/2]dhcp server lease day 1 hour 12

[R3-GigabitEthernet0/0/1]dhcp server dns-list 10.0.12.254
[R3-GigabitEthernet0/0/1]dhcp server excluded-ip-address 10.0.12.254
[R3-GigabitEthernet0/0/1]dhcp server lease day 1 hour 12

Run the display ip pool interface command on the router to view the
configured parameters of the interface address pool. For R3 the interface is
Gigabit Ethernet 0/0/1.

<R1>display ip pool interface GigabitEthernet0/0/2
Pool-name : GigabitEthernet0/0/2
Pool-No : 1
Lease : 1 Days 12 Hours 0 Minutes
Domain-name : -
M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 5 FTP and DHCP

Page122 HUAWEI TECHNOLOGIES HC Series

DNS-server0 : 10.0.23.254
NBNS-server0 : -
Netbios-type : -
Position : Interface Status : Unlocked
Gateway-0 : 10.0.23.1
Mask : 255.255.255.0
VPN instance : --
----------------------------------------------------------------------------
Start End Total Used Idle(Expired) Conflict Disable
----------------------------------------------------------------------------
10.0.23.1 10.0.23.254 253 0 252(0) 0 1
----------------------------------------------------------------------------

Flush the existing Vlanif1 address from S2 to allow for dynamic allocation of a
new IP address from the interface GigabitEthernet0/0/2 pool.

[S2]interface Vlanif 1
[S2-Vlanif1]shutdown
[S2-Vlanif1]undo shutdown

Enable interface Gigabit Ethernet 0/0/2 to allow the DHCP server to become
active on the network and to begin sending DHCP discover messages.
[R1]interface GigabitEthernet0/0/2
[R1-GigabitEthernet0/0/2]undo shutdown

<R1>display ip pool interface GigabitEthernet0/0/2
Pool-name : GigabitEthernet0/0/2
Pool-No : 1
Lease : 1 Days 12 Hours 0 Minutes
Domain-name : -
DNS-server0 : 10.0.23.254
NBNS-server0 : -
Netbios-type : -
Position : Interface Status : Unlocked
Gateway-0 : 10.0.23.1
Mask : 255.255.255.0
VPN instance : --
----------------------------------------------------------------------------
Start End Total Used Idle(Expired) Conflict Disable
----------------------------------------------------------------------------
10.0.23.1 10.0.23.254 253 1 251(0) 0 1
----------------------------------------------------------------------------
M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 5 FTP and DHCP

HC Series HUAWEI TECHNOLOGIES Page123

<S2>display ip interface brief
output omitted
Interface IP Address/Mask Physical Protocol
MEth0/0/1 unassigned down down
NULL0 unassigned up up(s)
Vlanif1 10.0.23.253/24 up up

The interface Vlanif1 shows to have been allocated an address from the
GigabitEthernet0/0/2 address pool of R1.

Flush the existing Vlanif1 address from S1 to allow for dynamic allocation of a
new IP address from the interface GigabitEther0/0/1 pool.

[S1]interface Vlanif 1
[S1-Vlanif1]shutdown
[S1-Vlanif1]undo shutdown

Enable interface Gigabit Ethernet 0/0/1 to allow the DHCP server to become
active on the network and to begin sending DHCP discover messages.

[R3]interface GigabitEthernet 0/0/1
[R3-GigabitEthernet0/0/1]undo shutdown

Verify that the new IP address as been allocated from the interface pool.

<R3>display ip pool interface GigabitEthernet0/0/1
Pool-name : GigabitEthernet0/0/1
Pool-No : 1
Lease : 1 Days 12 Hours 0 Minutes
Domain-name : -
DNS-server0 : 10.0.12.254
NBNS-server0 : -
Netbios-type : -
Position : Interface Status : Unlocked
Gateway-0 : 10.0.12.3
Mask : 255.255.255.0
VPN instance : --
----------------------------------------------------------------------------
Start End Total Used Idle(Expired) Conflict Disable
----------------------------------------------------------------------------
10.0.12.1 10.0.12.254 253 1 251(0) 0 1
----------------------------------------------------------------------------
M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 5 FTP and DHCP

Page124 HUAWEI TECHNOLOGIES HC Series

<S1>display ip interface brief
output omitted
Interface IP Address/Mask Physical Protocol
MEth0/0/1 unassigned down down
NULL0 unassigned up up(s)
Vlanif1 10.0.12.253/24 up up

It should also be noted that a default static route pointing to the DHCP server is
automatically generated by the switch, as seen in the final configuration below.
Final Configuration
[R1]display current-configuration
[V200R003C00SPC200]
#
sysname R1
#
dhcp enable
#
ip pool pool1
gateway-list 10.0.12.1
network 10.0.12.0 mask 255.255.255.0
lease day 1 hour 12 minute 0
#
interface GigabitEthernet0/0/1
shutdown
ip address 10.0.12.1 255.255.255.0
dhcp select global
#
interface GigabitEthernet0/0/2
ip address 10.0.23.1 255.255.255.0
dhcp select interface
dhcp server excluded-ip-address 10.0.23.254
dhcp server lease day 1 hour 12 minute 0
dhcp server dns-list 10.0.23.254
#
user-interface con 0
authentication-mode password
set authentication password cipher %$%$+L'YR&IZt'4,)>-*#lH",}%K-oJ_M9+'lOU~bD
(\WTqB}%N,%$%$user-interface vty 0 4
#
return
M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 5 FTP and DHCP

HC Series HUAWEI TECHNOLOGIES Page125


[R3]dis current-configuration
[V200R003C00SPC200]
#
sysname R3
#
dhcp enable
#
ip pool pool2
gateway-list 10.0.23.3
network 10.0.23.0 mask 255.255.255.0
lease day 1 hour 12 minute 0
#
interface GigabitEthernet0/0/1
ip address 10.0.12.3 255.255.255.0
dhcp select interface
dhcp server excluded-ip-address 10.0.12.254
dhcp server lease day 1 hour 12 minute 0
dhcp server dns-list 10.0.12.254
#
interface GigabitEthernet0/0/2
shutdown
ip address 10.0.23.3 255.255.255.0
dhcp select global
#
user-interface con 0
authentication-mode password
set authentication password cipher %$%$ksXDMg7Ry6yUU:63:DQ),#/sQg"@*S\U#.s.bHW
xQ,y%#/v,%$%$
user-interface vty 0 4
#
return

<S1>dis current-configuration
#
!Software Version V100R006C00SPC800
sysname S1
#
dhcp enable
#
interface Vlanif1
ip address dhcp-alloc
#
M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HCNA-HNTD Chapter 5 FTP and DHCP

Page126 HUAWEI TECHNOLOGIES HC Series

ip route-static 0.0.0.0 0.0.0.0 10.0.12.3
#
user-interface con 0
user-interface vty 0 4
#
return

<S2>display current-configuration
#
!Software Version V100R006C00SPC800
sysname S2
#
dhcp enable
#
interface Vlanif1
ip address dhcp-alloc
#
ip route-static 0.0.0.0 0.0.0.0 10.0.23.1
#
user-interface con 0
user-interface vty 0 4
#
return
M
o
r
e

L
e
a
r
n
i
n
g

R
e
s
o
u
r
c
e
s
:

h
t
t
p
:
/
/
l
e
a
r
n
i
n
g
.
h
u
a
w
e
i
.
c
o
m
/
e
n
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential 1
The privilege of HCNA/HCNP/HCIE:
With any Huawei Career Certification, you have the privilege on http://learning.huawei.com/en to enjoy:
1Comprehensive E-Learning Courses
ContentAll Huawei Career Certification E-Learning courses
Methods to get the E-learning privilege : submit Huawei Account and email being used for Huawei Account
registration to [email protected] .
2 Training Material Download
Content: Huawei product training material and Huawei career certification training material
MethodLogon http://learning.huawei.com/en and enter HuaWei Training/Classroom Training ,then you can
download training material in the specific training introduction page.
3 Priority to participate in Huawei Online Open Class(LVC)
ContentThe Huawei career certification training covering all ICT technical domains like R&S, UC&C, Security,
Storage and so on, which are conducted by Huawei professional instructors
MethodThe plan and participate method please refer to LVC Open Courses Schedule
4Learning Tool: eNSP
eNSP (Enterprise Network Simulation Platform) is a graphical network simulation tool which is developed by
Huawei and free of charge. eNSP mainly simulates enterprise routers, switches as close to the real hardware as
it possible, which makes the lab practice available and easy without any real device.
In addition, Huawei has built up Huawei Technical Forum which allows candidates to discuss technical issues with
Huawei experts , share exam experiences with others or be acquainted with Huawei Products(
http://support.huawei.com/ecommunity/
More
Learning
Resources:
http://learning.huawei.com/en