Power Supply 1

Circuit Diagram
Power supply unit:
As we all know any invention of latest

technology cannot be activated without the source of
power. So it this fast moving world we deliberately
need a proper power source which will be apt for a
particular requirement. All the electronic components
starting from diode to Intel IC’s only work with a DC
supply ranging from -+5v to -+12v. We are
utilizing for the same, the cheapest and commonly
available energy source of 230v-50Hz and stepping
down, rectifying, filtering and regulating the voltage.
This will be dealt briefly in the forth-coming sections.
STEP DOWN TRANSFORMER:
When AC is applied to the primary winding of the
power transformer it can either be stepped down or
up depending on the value of DC needed. In our
circuit the transformer of 230v/15-0-15v is used to
perform the step down operation where a 230V AC
appears as 15V AC across the secondary winding.
One alteration of input causes the top of the
transformer to be positive and the bottom negative.
The next alteration will temporarily cause the
reverse. The current rating of the transformer used in
our project is 2A. Apart from stepping down AC
voltages, it gives isolation between the power source
and power supply circuitries.
RECTIFIER UNIT:
In the power supply unit, rectification is normally
achieved using a solid state diode. Diode has the
property that will let the electron flow easily in one
direction at proper biasing condition. As AC is applied
to the diode, electrons only flow when the anode and
cathode is negative. Reversing the polarity of voltage
will not permit electron flow.
A commonly used circuit for supplying large
amounts of DC power is the bridge rectifier. A bridge
rectifier of four diodes (4*IN4007) are used to
achieve full wave rectification. Two diodes will
conduct during the negative cycle and the other two
will conduct during the positive half cycle. The DC
voltage appearing across the output terminals of the
bridge rectifier will be somewhat lass than 90% of
the applied rms value. Normally one alteration of the
input voltage will reverse the polarities. Opposite
ends of the transformer will therefore always be 180
deg out of phase with each other.
For a positive cycle, two diodes are connected to
the positive voltage at the top winding and only one
diode conducts. At the same time one of the other
two diodes conducts for the negative voltage that is
applied from the bottom winding due to the forward
bias for that diode. In this circuit due to positive half
cycleD1 & D2 will conduct to give 10.8v pulsating
DC. The DC output has a ripple frequency of 100Hz.
Since each altercation produces a resulting output
pulse, frequency = 2*50 Hz. The output obtained is
not a pure DC and therefore filtration has to be done.
FILTERING UNIT:
Filter circuits which are usually capacitors
acting as a surge arrester always follow the rectifier
unit. This capacitor is also called as a decoupling
capacitor or a bypassing capacitor, is used not only
to ‘short’ the ripple with frequency of 120Hz to
ground but also to leave the frequency of the DC to
appear at the output. A load resistor R1 is connected
so that a reference to the ground is maintained.
C1R1 is for bypassing ripples. C2R2 is used as a low
pass filter, i.e. it passes only low frequency signals
and bypasses high frequency signals. The load
resistor should be 1% to 2.5% of the load.
1000∝f/25v : for the reduction of ripples from the

pulsating.
10∝ f/25v : for maintaining the stability of the

voltage at the load side.
O, 1∝ f : for bypassing the high frequency

disturbances.
VOLTAGE REGULATORS:
The voltage regulators play an important role in
any power supply unit. The primary purpose of a
regulator is to aid the rectifier and filter circuit in
providing a constant DC voltage to the device. Power
supplies without regulators have an inherent problem
of changing DC voltage values due to variations in
the load or due to fluctuations in the AC liner voltage.
With a regulator connected to the DC output, the
voltage can be maintained within a close tolerant
region of the desired output. IC7812 and 7912 is
used in this project for providing +12v and –12v DC
supply.
Specifications:
Resistors R1 and R2 maintain line load regulation.

At the secondary side of the transformer,
Applied voltage = 15v
Conducting drop across the diodes = 2*0.6= 1.2v.
Without capacitor:
Vavg = (15-1.2)v = 13.8c pulsating DC
Frequency = 100Hz
With capacitor:
V=Vavg *1.414(form factor) = 19.51v.
Frequency = 0Hz
With 7812 voltage regulator:
V0= +12v
With 7912 voltage regulator:
V0= -12v

Power Supply 1

Uploaded by

Copyright:

Available Formats

Power Supply 1

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Power Supply 1

Uploaded by

Copyright:

Available Formats

Circuit Diagram

Power supply unit:

As we all know any invention of latest

1000∝f/25v : for the reduction of ripples from the

10∝ f/25v : for maintaining the stability of the

O, 1∝ f : for bypassing the high frequency

Resistors R1 and R2 maintain line load regulation.

You might also like