System Abends

S001 - AN INPUT/OUTPUT ERROR CONDITION WAS ENCOUNTERED DURING

EXECUTION OF A CHECK/GET/PUT MACRO INSTRUCTION. EITHER NO
SYNAD ROUTINE WAS PROVIDED TO HANDLE THE ERROR, OR
DCB=EROPT=ABE WAS SPECIFIED OR DEFAULTED.
IF THE REGISTER 15 RETURN CODE IS AVAILABLE, SUPPLY IT IN THE S1
OPERAND FOR MORE SPECIFIC INFORMATION! H ABEND O"S1-RC#
POSSIBLE CAUSE
INPUT RECORD DESCRIBED INCORRECTLY, LENGTH ERROR
TRIED TO READ AFTER ENCOUNTERING END OF FILE
RECFM V IS INCOMPATIBLE WITH TRTCH ET
TRIED TO WRITE ON AN INPUT FILE
READ INTO A TABLE WHOSE SUBSCRIPT WAS $ERO
INCORRECT LABEL PARAMETER
TRTCH PARM WAS WRONG
TAPE BEING READ IN WRONG DENSITY
DIRECTORY OF PDS WAS OVERWRITTEN
NSL LABEL HAD INCORRECT DSNAME, OPERATOR CANCELLED
TRUE I/O FAILURE, UCB SHOW REDUNDANCY
HARDWARE ERROR - BAD TAPE OR TAPE DRIVE
SECONDARY SPACE ALLOCATION FOR DASD OUTPUT FILE TOO SMALL "SEE
SB%&#
COBOL - INCORRECT USE OF BLOCK CONTAINS CLAUSE
- HAD RECORDING MODE F WHEN GENERATED, BUT NOT WHEN READ
S001 - 01 - AN I/O ERROR OCCURRED DURING BDAM CREATE, BSAM, BISAM,
'SAM, OR BDAM AND NO SYNAD EXIT WAS SPECIFIED BY THE USER.
S001 - 02 - AN ERROR WAS ENCOUNTERED WHILE ATTEMPTING TO CLOSE
THE DATASET.
((S1 - % - FOR 'SAM, AN ERROR WAS ENCOUNTERED THAT COULD NOT
BE ACCEPTED.
S001 - 04 - FOR 'SAM, ABE OR AN INVALID VALUE FOR EROPT PARAMETER
IN THE DCB AND/OR NO ERROR HANDLING "SYNAD# EXIT WAS SPECIFIED.
S001 - 05 - FOR 'SAM, A GET WAS ISSUED AFTER END-OF-FILE.
S002 - RECORD IS GREATER THAN %),&*+ BYTES, EXCEEDS MAXIMUM
TRACK LENGTH OR STATED BLOCKSI$E, COULD NOT BE CONTAINED IN
ONE EXTENT, OR TOO MANY TRACKS SPECIFIED FOR CYLINDER
OVERFLOW.
IF THE REGISTER 15 RETURN CODE IS AVAILABLE, SUPPLY IT IN THE
S) OPERAND FOR MORE SPECIFIC INFORMATION! H ABEND O"S)-RC#
POSSIBLE CAUSE
DCB HAD THE WRONG BLOCK SI$E
IEHMOVE - ATTEMPT TO RENAME DATA SET WHEN NEW NAME ALREADY
EXISTS
WRONG RECORD FORMAT SPECIFIED IN ,CL
S002 - 04 - AN INVALID RECORD WAS ENCOUNTERED ON A GET OPERATION.
THE LENGTH FIELD OF A RECORD DESCRIPTOR WORD "RDW# FOR A
VARIABLE LENGTH RECORD SPECIFIES A VALUE LESS THAN -.
S002 - 08 - AN INVALID RECORD WAS ENCOUNTERED ON A PUT OR WRITE
OPERATION. THE RECORD OR BLOCK LENGTH PLUS THE KEY LENGTH AND
RE'UIRED OVERHEAD ADD UP TO MORE THAN %),&*& BYTES.
S002 - 0C - AN INVALID RECORD WAS ENCOUNTERED ON A PUT OR WRITE
OPERATION. THE RECORD OR BLOCK LENGTH PLUS THE KEY LENGTH AND
RE'UIRED OVERHEAD IS GREATER THAN THE DASD TRACK CAPACITY.
S002 - 10 - AN INVALID RECORD WAS ENCOUNTERED ON A PUT OPERATION.
THE DATASET USES THE TRACK OVERFLOW FEATURE. THE RDW FOR A
VARIABLE LENGTH RECORD SPECIFIES A LENGTH GREATER THAN %),&5).
S002 - 14 - AN INVALID RECORD WAS ENCOUNTERED ON A PUT OR WRITE
OPERATION. THE RECORD LENGTH IS GREATER THAN THE BLOCKSI$E
SPECIFIED IN THE DCB.
S002 - 18 - AN INVALID RECORD WAS ENCOUNTERED ON A PUT OPERATION.
THE DATASET USES THE VARIABLE RECORD FORMAT. THE LENGTH VALUE
OF THE RDW IS EITHER! LESS THAN -, GREATER THAN %),&*&, GREATER
THAN THE BLOCKSI$E SPECIFIED IN THE DCB, OR LESS THAN 5 IF ASA
CONTROL CHARACTERS ARE BEING USED.
S002 - 1C - THE ERROR OCCURRED DURING THE CREATION OF A DIRECT
DATASET. A WRITE MACRO WAS ISSUED FOR A RECORD LARGER THAN THE
TRACK CAPACITY, AND THE RECORD FORMAT DOES NOT USE THE TRACK
OVERFLOW FEATURE.
S002 - 20 - THE ERROR OCCURRED DURING THE CREATION OF A DIRECT
DATASET. A WRITE MACRO WAS ISSUED CAUSING A SECONDARY EXTENT
TO BE OBTAINED. THE BLOCK WILL NOT FIT ON THE AMOUNT OF SPACE
ALLOCATED FOR THE
SECONDARY EXTENT.
S002 - 24 - THE ERROR OCCURRED DURING THE CREATION OF A DIRECT
DATASET. A WRITE MACRO WAS ISSUED TO WRITE OUT A BLOCK LARGER
THAN THE PRIMARY EXTENT ON THE PREALLOCATED DATASET. THIS
COULD ALSO OCCUR IF ALLOCATION OF THE PRIMARY EXTENT WAS NON-
CONTIGUOUS AND ANY OF THE SECONDARY EXTENTS WERE SMALLER
THAN THE BLOCK.
S002 - 28 - THE ERROR OCCURRED DURING THE CREATION OF A DIRECT
DATASET. DURING THE EXECUTION OF OPEN IT WAS DETECTED THAT THE
BLOCKSI$E WAS LARGER THAN THE PRIMARY EXTENT.
S002 - 2C - THE ERROR OCCURRED WHILE OPENING AN ISAM DATASET. TOO
MANY TRACKS WERE SPECIFIED FOR CYLINDER OVERFLOW.
S002 - 30 - ONE OF THE FOLLOWING IS TRUE!
- A READ WAS ISSUED BUT THE LENGTH TO BE READ WAS $ERO.
- A 'SAM PUT WITH MOVE MODE WAS ISSUED FOR RECFM=F, FB OR U BUT
DCBLRECL CONTAINED A NON-POSITIVE VALUE.
S002 - 34 - A READ MACRO WAS ISSUED FOR AN OUTPUT-ONLY DASD DATA
SET.
S002 - 3C - PDSE MEMBER CREATION WAS PREVENTED BECAUSE THE PDSE
ALREADY HAD THE MAXIMUM NUMBER OF MEMBERS ")((1/ - )#.
S002 - 50 - SERIALI$ATION OF AN INTERNAL SAM CONTROL BLOCK "SACB#
USED FOPR PROCESSING HAS BEEN VIOLATED.
S002 - 54 - DEBCHK FAILURE DURING PDSE PROCESSING.
S002 - 58 - AN INTERNAL SAM CONTROL BLOCK "SACB# USED FOR
PROCESSING PDSE RE'UESTS IS INCORRECT.
S002 - 5C - AN INTERNAL SAM CONTROL BLOCK "FR'# USED FOR 'UEUING
PDSE RE'UESTS IS INCORRECT.
S002 - 60 - NON-$ERO KEYLENGTH SPECIFIED FOR OUTPUT PDSE MEMBER.
S002 - 64 - FOR BSAM, THE READ OR WRITE RE'UEST COULD NOT BE
ACCEPTED BECAUSE THE VALUE OF NCP INT THE DCB HAD ALREADY BEEN
REACHED.
S002 - 68 - INCORRECT BLOCKSI$E SPECIFIED.
S002 - 6C - UNABLE TO CREATE A PDSE MEMBER.
S002 - 70 - UNABLE TO UPDATE AN INTERNAL SAM CONTROL BLOCK "PACB#
USED FOR PDSE PROCESSING WITH INFORMATION CONCERNING THE
MEMBER BEING ACCESSED.
S002 - 74 - AN INTERNAL SAM CONTROL BLOCK "PACB# USED FOR STORING
PDSE DIRECTORY AND MEMBER INFORMATION IS INCORRECT.
S002 - 78 - ERROR RETURN FROM IGWFMPCR WHEN ATTEMPTING TO GIVE
CONTROL TO A ROUTINE TO PROCESS PDSE RE'UESTS.
S002 - 7C - POINT DETECTED THAT INFORMATION CONCERNING THE
MEMBER BEING ACCESSED IS NOT FOUND IN THE PACB.
S002 - 80 - POINT DETECTED AN ERROR WHILE ATTEMPTING TO
SYNCHRONI$E DATA ON OUTPUT.
S002 - 84 - POINT DETECTED AN ERROR WHILE ATTEMPTING TO RECONNECT
TO A PDSE MEMBER FOR HOLD.
S002 - 88 - POINT DETECTED AN ERROR WHILE ATTEMPTING TO RECONNECT
TO A PDSE MEMBER FOR I/O.
S002 - 8C - POINT DETECTED AN ERROR WHILE ATTEMPTING TO
DISCONNECT FROM A PDSE MEMBER.
S002 - 90 - POINT DETECTED AN ERROR WHILE ATTEMPTING TO CONNECT
TO A PDSE MEMBER.
S002 - 94 - INCORRECT ATTEMPT TO CREATE A PDSE MEMBER SINCE THE
MAXIMUM NUMBER OF MEMBERS HAVE ALREADY BEEN CREATED.
S002 - 98 - UNABLE TO COMPLETE A WRITE RE'UEST ISSUED WITHIN A
PDSE MEMBER.
S002 - 9C - INCORRECT UPDATE WRITE DETECTED. ALL OUTSTANDING
READS HAD NOT BEEN CHECKED PRIOR TO THE WRITE.
S002 - A0 - INCORRECT ATTEMPT TO ACCESS A PDSE DIRECTORY. EITHER!
- WRITE ATTEMPTED TO THE DIRECTORY OF A PDSE.
- READ ATTEMPTED TO THE DIRECTORY OF A PDSE AND EITHER THE RECFM
WAS NOT F WITH BLKSI$E 0= )5*
OR
RECFM WAS NOT U WITH BLKSI$E 0= )5*.
S002 - A4 - UNABLE TO COMPLETE THE READ AGAINST THE PDSE
DIRECTORY DUE TO AN ERROR RETURN CODE FROM AN SMS SERVICE
USED TO OBTAIN DIRECTORY INFORMATION.
S002 - A8 - MAXIMUM NUMBER OF RECORDS IN MEMBER HAS BEEN
EXCEEDED.
S002 - AC - BAD BUFFER FORMAT DETECTED FOR VARIABLE LENGTH
RECORDS.
EITHER!
- RDW LENGTH IS LESS THAN -.
- LENGTH OF SPANNED RECORD IS GREATER THAN %)&*.
- THE SUM OF THE LENGTHS IN THE RDWS PLUS - DOES NOT E'UAL THE
LENGTH SPECIFIED IN THE BDW.
- RECFM DOES NOT SPECIFY BLOCKED BUT MORE THAN 1 RDW IN BUFFER.
S002 - B0 - EITHER RECFM=F AND DCBBLKSI DOES NOT E'UAL DCBLRECL,
OR RECFM=FB AND DCBBLKSI IS NOT A MULTIPLE OF DCBLRECL.
S003 - THE ERROR OCCURED DURING END-OF-BLOCK PROCESSING USING
EITHER BSAM OR 'SAM. THE ERROR OCURRED BECAUSE THE I/O MACRO
INSTRUCTIONS FOR A %5)5-ASSOCIATED DATA SET WERE NOT EXECUTED IN
THE PROPER SE'UENCE.
- IF THE REGISTER 15 RETURN CODE IS AVAILABLE, SUPPLY IT IN THE
- S% OPERAND FOR MORE SPECIFIC INFORMATION! H ABEND O"S%-RC#
S003 - 01 - THE ERROR WAS A READ SE'UENCE ERROR.
S003 - 02 - THE ERROR WAS A PUNCH SE'UENCE ERROR.
S003 - 03 - THE ERROR WAS A PRINT SE'UENCE ERROR.
S004 - THE ERROR OCCURED DURING OPEN PROCESSING USING EITHER
BSAM OR 'SAM BECAUSE A CONFLICTING OR INVALID DCB PARAMETER
"FUNC OR RELATED PARAMETER# IS SPECIFIED.
- IF THE REGISTER 15 RETURN CODE IS AVAILABLE, SUPPLY IT IN THE
- S- OPERAND FOR MORE SPECIFIC INFORMATION! H ABEND O"S--RC#
S004 - 01 - INVALID DCB FUNC PARAMETER SPECIFIED.
S004 - 02 - INVALID COMBINATION OF DCB FUNC PARAMETER AND CNTRL
MACRO SPECIFIED.
S004 - 03 - CONFLICTING ACCESS METHODS SPECIFIED.
S004 - 04 - INVALID DCB SPECIFIED FOR %55 OR %5)5.
S004 - 05 - INVALID FORMAT CARD OR AN INVALID DEVICE SPECIFIED WITH
OPTICAL MARK READ "OMR#.
S004 - 06 - DATA PROTECTION IMAGE NOT FOUND IN THE SYS1.IMAGELIB
DATA SET, VOLUME CONTAINING SYS1.IMAGELIB NOT MOUNTED, OR
SYS1.IMAGELIB NOT CATALOGED.
S005 - THE ERROR OCCURRED BECAUSE OF AN INVALID DECB DURING
READ PROCESSING USING BSAM.
- IF THE REGISTER 15 RETURN CODE IS AVAILABLE, SUPPLY IT IN THE
- S5 OPERAND FOR MORE SPECIFIC INFORMATION! H ABEND O"S5-RC#
S005 - 04 - A RE'UIRED ADDRESS WAS NOT SPECIFIED IN THE DECB. THIS
CAN BE EITHER THE HEADER ADDRESS AND/OR THE AREA ADDRESS.
S005 - 08 - THE RBL TYPE OF READ WAS NOT USED FOR THE %++*.
S006 - THE PROGRAM HAD AN INCORRECT AUTHORI$ATION TO RUN A 1-1/.
S008 - THE ERROR OCCURRED DURING EXECUTION OF A SYNAD ROUTINE.
THE ROUTINE WAS GIVEN CONTROL FOLLOWING EXECUTION OF A BSAM
CHECK MACRO INSTRUCTION.
S013 - CONFLICTING OR UNSUPPORTED PARAMETERS IN DCB. MEMBER
NAME SPECIFIED IN DD NOT FOUND. NO DIRECTORY ALLOCATION
SUBPARAMETER IN DD.
- IF THE REGISTER 15 RETURN CODE IS AVAILABLE, SUPPLY IT IN THE
- S1% OPERAND FOR MORE SPECIFIC INFORMATION! H ABEND O"S1%-RC#
POSSIBLE CAUSE
DCB PARAMETERS CONFLICT, NO BLKSI$E OR NOT VALID MULTIPLE OF
LRECL
MISSING OR MISPLACED SYSIN DD CARD
PARTITIONED DATA SET MEMBER NOT FOUND
MERGE - SORTIN1 DOES NOT CONTAIN THE MAXIMUM BLOCKSI$E
,CL - TRIED TO CREATE A PDS WITHOUT ALLOCATING DIRECTORY BLOCKS
S013 - 04 - AMERICAN NATIONAL STANDARD LABELS WERE SPECIFIED IN
THE LABEL PARAMETER OF THE DD STATEMENT, BUT ARE NOT SUPPORTED
BY THE SYSTEM. CORRECT THE LABEL PARAMETER.
- OPTCD=' WAS SPECIFIED BUT IS NOT SUPPORTED BY THE SYSTEM.
CORRECT THE DCB OPTCD OPTION.
S013 - 08 - AMERICAN NATIONAL STANDARD LABELS WERE SPECIFIED IN
THE LABEL PARAMETER OF THE DD STATEMENT, BUT THE UNIT
PARAMETER SPECIFIED A &-TRACK TAPE DRIVE. ANSI LABELS A VALID
ONLY FOR /-TRACK UNITS.
S013 - 0C - A BUFFER LENGTH OF WAS SPECIFIED FOR A BDAM DATASET
FOR WHICH DYNAMIC BUFFERING WAS RE'UESTED.
S013 - 10 - AN OPEN MACRO WAS ISSUED FOR A NULL DATASET AND
BLKSI$E AND BUFL ARE BOTH . SPECIFY ONE OR THE OTHER AS NON-
$ERO.
S013 - 14 - AN OPEN MACRO WAS ISSUED WITH OUTPUT OR OUTIN
SPECIFIED. DCB SPECIFIES DSORG=PO, BUT THE DSCB INDICATES THE
DATASET IS NOT PARTITIONED. CHANGE DSORG TO PS, OR CREATE
DATASET AS PDS.
- AN OPEN MACRO WAS ISSUED WITH INPUT SPECIFIED. THE DSCB
INDICATES THAT DSORG=PO, BUT THE DCB SPECIFIES NEITHER DSORG=PO
NOR PS.
S013 - 18 - AN OPEN WAS ISSUED FOR A PARTITIONED DATASET. THE
SPECIFIED MEMBER NAME WAS NOT FOUND IN THE DATASET.
S013 - 1C - AN OPEN MACRO WAS ISSUED FOR A PARTITIONED DATASET,
BUT AN I/O ERROR WAS ENCOUNTERED SEARCHING THE DIRECTORY.
S013-20 - OPEN MACRO INSTR FOR SE'UENTIAL DATASET USING DCB,
BLKSI$E IS NOT A MULTIPLE OF THE LRECL.
S013 - 24 - AN OPEN WAS ISSUED WITH INPUT, INOUT, RDBACK, OR UPDATE
SPECIFIED, BUT THE DCB MACRF DID NOT SPECIFY EXCP, GET, OR READ.
S013 - 28 - AN OPEN MACRO WAS ISSUED WITH OUTPUT OR OUTIN
SPECIFIED, BUT THE DCB DID NOT SPECIFY A MACRF OF EXCP, PUT, OR
WRITE.
S013 - 2C - A SE'UENTIAL DATASET USING THE 'UEUED ACCESS
TECHNI'UE WITH EXCHANGE BUFFERING WAS OPENED FOR INPUT, BUT
THE BUFFER CONTROL BLOCK ADDRESS WAS .
S013 - 30 - A SE'UENTIAL DATASET USING THE 'UEUED ACCESS
TECHNI'UE WITH EXCHANGE BUFFERING WAS OPENED FOR OUTPUT, BUT
THE BUFFER CONTROL BLOCK ADDRESS "DCBBUFCB# WAS .
S013-34 - INVALID LRECL"INCOMPATIBLE DCB INFO#
S013 - 38 - AN OPEN MACRO WAS ISSUED FOR A SE'UENTIAL DATASET ON A
DIRECT ACCESS DEVICE WITH TRACK OVERFLOW, BUT THE BUFFER
CONTROL BLOCK ADDRESS WAS $ERO. THIS TYPE OF ERROR OFTEN
OCCURS IF A DCB IS SHARED BY TWO OR MORE TASKS, OR IS OPENED AND
CLOSED SEVERAL TIMES WITHIN ONE ,OB STEP.
S013 - 3C - A SE'UENTIAL DATASET WAS OPENED FOR INPUT OR OUTPUT,
BUT THE BUFFER CONTROL BLOCK ADDRESS WAS . THIS TYPE OF ERROR
OFTEN OCCURS IF A DCB IS SHARED BY TWO OR MORE TASKS, OR IS
OPENED AND CLOSED SEVERAL TIMES WITHIN ONE ,OB STEP.
S013 - 40 - A SE'UENTIAL OR DIRECT DATASET WAS OPENED FOR INPUT,
BUT THE BUFFER CONTROL BLOCK ADDRESS WAS .
S013 - 44 - AN OPEN MACRO WAS ISSUED FOR A DATASET ON A DIRECT
ACCESS DEVICE FOR WHICH CHAINED SCHEDULING WAS SPECIFIED, BUT
THE BUFFER CONTROL BLOCK ADDRESS WAS .
S013 - 48 - AN OPEN MACRO WAS ISSUED FOR A SE'UENTIAL DATASET
USING THE 'UEUED ACCESS TECHNI'UE, BUT THE BUFFER CONTROL
BLOCK ADDRESS WAS $ERO.
S013 - 4C - AN OPEN MACRO WAS ISSUED FOR A SE'UENTIAL DATASET
USING THE 'UEUED ACCESS TECHNI'UE. THE SYSTEM DETERMINED THAT
A BUFFER POOL EXISTED FOR THIS DATASET AND MADE THE APPROPIATE
TEST SHOWN BELOW WITH UNSATISFACTORY RESULTS!
- IF THE DATA WAS TO BE SENT DIRECTLY TO A UNIT RECORD DEVICE "NO
SPOOLING#, THE BUFFER LENGTH VALUE IN THE BUFFER CONTROL BLOCK
HAD TO BE E'UAL TO OR GREATER THAN THE VALUE SPECIFIED IN THE
DCB FOR LOGICAL RECORD LENGTH "LRECL#.
- OTHERWISE, THE BUFFER LENGTH VALUE IN THE BUFFER CONTROL
BLOCK HAD TO BE E'UAL TO OR GREATER THAN THE VALUE SPECIFIED IN
THE DCB FOR BLKSI$E.
S013 - 50 - AN OPEN MACRO ISSUED FOR A DATASET ALLOCATED TO A
PRINTER DID NOT HAVE OUTPUT SPECIFIED AS AN OPEN OPTION.
S013 - 54 - NO SECONDARY CONTROL UNIT COULD NOT BE FOUND FOR A
1-1/.
S013 - 58 - AN OPEN MACRO WAS ISSUED FOR A PAPER TAPE DATASET AND
CONCATENATION WITH UNLIKE ATTRIBUTES WAS SPECIFIED.
S013 - 5C - AN OPEN MACRO WAS ISSUED FOR A SE'UENTIAL DATASET
USING THE 'UEUED ACCESS TECHNI'UE. THE DATASET CONTAINED
SPANNED VARIABLE LENGTH RECORDS LARGER THAN %),&5* BUT GET
LOCATE MODE WAS NOT USED.
ALTERNATIVELY, BFTEK=A WAS SPECIFIED WITH MACRF=GM OR
MACRF=PM.
S013 - 60 - AN OPEN MACRO WAS ISSUED FOR A DATASET WITH A DCB
SPECIFYING RECFM=F, AND BLKSI$E WAS NOT E'UAL TO LRECL. CORRECT
THE RECFM TO FB, OR MAKE LRECL AND BLKSI$E E'UAL.
S013 - 64 - AN OPEN MACRO WAS ISSUED FOR A NULL DATASET USING AN
ACCESS METHOD OTHER THAN 'SAM OR BSAM. THIS IS A NO-NO.
S013 - 68 - AN OPEN WAS ISSUED FOR A DATASET WHOSE DCB SPECIFIED
BLKSI$E GREATER THAN %),&*&, WHICH IS THE MAXIMUM ALLOWED.
S013 - 6C - AN OPEN MACRO WAS ISSUED FOR A DATASET WITH RECFM=T IN
THE DCB, RE'UESTING TRACK OVERFLOW, BUT THE DIRECT ACCESS
DEVICE DOES NOT SUPPORT TRACK OVERFLOW.
S013 - 70 - AN OPEN MACRO WAS ISSUED FOR A DATASET ON MAGNETIC
TAPE. A CONFLICT EXISTS AMONG LABEL PARAMETERS ON THE DD
STATEMENT, AND DCBRECFM, DCBOPTCD, DCBBUFOF, AND DCBUSASI GIVE
THE APPEARANCE
OF MIXED USASI AND EBCDIC ATTRIBUTES TO THE DATASET. OR OPTCD='
WAS SPECIFIED FOR A DATASET ON A DEVICE OTHER THAN MAGNETIC
TAPE.
S013 - 74 - AN OPEN MACRO WAS ISSUED FOR AN OPTICAL CHARACTER
READER DATASET, BUT THE OPEN OPTION DID NOT SPECIFY INPUT.
S013 - 78 - AN OPEN MACRO WAS ISSUED FOR AN OPTICAL CHARACTER
READER DATASET. THE BUFL PARAMETER IN THE DCB WAS SPECIFIED AS
$ERO.
S013 - 7C - AN OPEN MACRO WAS ISSUED FOR AN OPTICAL CHARACTER
READER DATASET, BUT THE LRECL PARAMETER IN THE DCB WAS $ERO.
S013 - 80 - AN OPEN MACRO WAS ISSUED FOR AN OPTICAL CHARACTER
READER DATASET, BUT THE BUFL WAS LESS THAN THE LRECL.
S013 - 84 - AN OPEN MACRO WAS ISSUED FOR AN OPTICAL CHARACTER
READER DATASET. THE NUMBER OF BUFFERS SPECIFIED IN THE BUFFER
POOL CONTROL BLOCK IS NOT THE SAME AS THAT SPECIFIED IN THE
DCBBUFNO.
S013 - 88 - AN OPEN MACRO WAS ISSUED FOR A TELECOMMUNICATIONS
DEVICE BUT THE DCBDSORG DID NOT SPECIFY TSO.
S013 - 8C - AN OPEN MACRO WAS ISSUED FOR A DIRECT ORGANI$ATION
DATASET "BDAM# BUT THE DCBRECFM PARAMETER WAS NOT SPECIFIED.
S013 - A4 - A DCB WAS OPENED FOR A SYSIN OR SYSOUT DATASET BUT THE
DSORG WAS NOT SPECIFIED AS PS.
S013 - A8 - AN INVALID RECORD FORMAT WAS RE'UESTED FOR A SYSIN OR
SYSOUT DATASET. "RECFM=D, VS, OR VBS ARE INVALID FOR SYSIN#
S013 - AC - A 'SAM OPEN WAS ISSUED WITH A NON-$ERO KEYLENGTH IN
THE DCB WHICH IS NOT SUPPORTED. "NOW SUPPORTED, BUT WITH INPUT
ONLY.#
S013 - B0 - AN OPEN MACRO WAS ISSUED WITH THE RDBACK OPTION FOR A
DCB SPECIFYING A RECORD FORMAT OF VARIABLE SPANNED RECORDS.
THESE ARE CONFLICTING PARAMETERS.
S013 - B4 - AN OPEN MACRO WAS ISSUED WITH THE INOUT/OUTIN OPTION
FOR A DCB SPECIFYING THE 'SAM MACRF VALUES. THESE ARE
CONFLICTING PARAMETERS.
S013 - B8 - AN OPEN MACRO WAS ISSUED FOR THE %+/ DOCUMENT
PROCESSOR AND DCBHDR WAS NOT SPECIFIED IN THE DCB.
S013 - BC - A SYSIN OR SYSOUT DCB WAS OPENED WITH INVALID OPTIONS.
EITHER OPEN SPECIFIED UPDAT OR RDBACK, OR THE POINT MACRO
FUNCTION WAS SPECIFIED IN MACRF=RP OR WP. REPOSITIONING OR
UPDATING A SPOOLED DATASET IS NOT PERMITTED.
S013 - C0 - A SYSIN OR SYSOUT DATASET COULD NOT BE OPENED BY A ,OB
ENTRY SUBSYSTEM. THE FAILING DCB IS NOT OPENED, HOWEVER THE
TASK IS NOT TERMINATED. PROCESSING CONTINUES FOR OTHER DCBS
OPENED.
S013 - C4- DURING THE CREATION OF A DIRECT DATASET, THE OPEN
ROUTINE FOUND THAT THE DCB SPECIFIED READ"R# OR GET"G# IN THE
MACRF FIELD. ONLY WRITE LOAD "WL# IS ALLOWED.
S013 - C8 - THE OPEN SUBSYSTEM EXECUTOR MODULE WAS PASSED AN
ERROR RETURN CODE IN REGISTER 15 AFTER ISSUING THE IEFSSRE'
MACRO TO CONNECT THE USER1S ACB TO THE SUBSYSTEM. THIS
INDICATES THE SUBSYSTEM WAS NOT OPERATING.
S013 - CC - SETPRT PROCESSING FAILED TO SET UP THE DEVICE DURING AN
OPEN FOR THE IBM %+ PRINTING SUBSYSTEM.
S013 - D0 - AN INVALID RECORD FORMAT OF FBS OR FS WAS SPECIFIED FOR
A PARTITIONED DATA SET.
S013 - D0 - A DB/DBS RECORD FORMAT WAS SPECIFIED FOR 'SAM LOCATE
MODE, BUT THE LOGICAL RECORD INTERFACE IS NOT PRESENT IN THE
ASSOCIATED BUFFER CONTROL BLOCK. IE. SEGMENT MODE IS IMPLIED.
S013 - D8 - A CONFLICT HAS OCCURRED FOR THE SPANNED RECORD
FORMAT EXTENDED LOGICAL RECORD INTERFACE "XLRI#. BUFFER
CONTROL BLOCK. IE. SEGMENT MODE IS IMPLIED.
S013 - E4 - THE LIMIT OF 1)% EXTENTS FOR A CONCATENATED PARTITIONED
DATA SET HAS BEEN EXCEEDED. "USED TO BE )5* EXTENTS2#
S013 - E8 - THE OPEN VERIFICATION FUNCTION OF THE IEFSSRE' MACRO
RETURNED AN ERROR CODE IN REGISTER 15.
S014 - 04 - "- IS THE ONLY POSSIBLE RETURN CODE ASSOCIATED WITH
S1-#
- THE TASK WHICH ISSUED A CLOSE FOR A DASD DATA SET WAS NOT THE
TASK WHICH OPENED THE DATA SET.
S016 - AN ERROR OCCURRED IN SAM SIO/PAGE FIX OR DASD END-OF-
BLOCK MODULES BECAUSE OF ONE OF THE FOLLOWING!
- THE DASD END-OF-BLOCK MODULES ISSUED AN EXCPVR SVC RE'UEST
ON BEHALF OF A USER RE'UEST, BUT A PREVIOUS EXCPVR SVC RE'UEST
HAD NOT COMPLETED. ONE OF THE FOLLOWINF OCCURRED!
- A DATA EXTENT CONTROL BLOCK "DECB# WAS USED TWICE.
- MULTIPLE READS OR WRITES WERE ISSUED, BUT ONLY THE LAST READ
OR WRITE WAS CHECKED.
- AN EXCPVR SVC RE'UEST ON BEHALF OF A USER RE'UEST WAS GOING
TO BE ISSUED TO READ A DATA SET THAT IS EXECUTE ACCESS PROTECTED,
BUT THE USER IS NOT IN SUPERVISOR STATE. "THE SAM SIO APPENDAGE
ISSUED THIS ABEND.#
S020 - DURING AN OPEN FOR A BDAM DATA SET THE CONTROL PROGRAM
FOUND THAT DCBMACRF DID NOT CONTAIN AN A, K OR I "RC=-#, OR THE
BDAM DATA SET CONTAINED $ERO EXTENTS "RC=+#.
S021 - A CALLER OF THE ASCBCHAP ROUTINE PASSED TO ASCBCHAP AN
ASCB ADDRESS THAT HAD BITS SET TO ONE IN ITS HIGH ORDER BYTE.
S022 - THE VPSS ENCOUNTERED A MISSING DEVICE END ON CONTROL PORT
.
S023 - LNKLST LOOKASIDE "LLA# COULD NOT OBTAIN ALL THE LNKLST
DIRECTORY ENTRIES.
S024 - AN ABNORMAL TERMINATION OCCURRED IN PRINT SERVICES
FACILITY.
S027 - AN ABNORMAL TERMINATION OCCURRED IN PRINT SERVICES
FACILITY.
S028 - A PAGING OPERATION HAS NOT COMPLETED SUCCESSFULLY DUE TO
ONE OF THE FOLLOWING!
- A PERMANENT I/O ERROR OCCURRED WHILE ATTEMPTING A PAGE-IN OR
SWAP-IN OPERATION. THE DATA BEING PAGED IN OR SWAPPED IN IS LOST.
- A REAL STORAGE MANAGEMENT ROUTINE OR ANOTHER SYSTEM
ROUTINE PERFORMING A SERVICE FOR RSM SUFFERED AN INTERMEDIATE
ERROR. THE FUNCTION PERFORMED IS TERMINATED.
- A AUXILIARY STORAGE MANAGEMENT ROUTINE SUFFERED A
TRANSLATION ERROR WHILE USING THE CONTROL REGISTER OF ANOTHER
ADDRESS SPACE TO UPDATE THAT ADDRESS SPACE1S LS'A.
S029 - LINES EXCEEDED
S02A - ,ES) FOUND THAT DATA MANAGEMENT CONTROL BLOCKS OR THE
,ES) UBUF CONTROL BLOCK WAS NO LONGER VALID DURING EXECUTION
OF A DATA MANAGEMENT RE'UEST FOR A SPOOL DATA SET.
S02B - A USER EXIT ROUTINE ISSUED A RETURN CODE GREATER THAN THAT
SPECIFIED IN THE 3MAXRC PARAMETER OF THE 4EXIT555 MACRO.
S02C - AN ERROR OCCURRED IN ,ES) SUPPORT OF AN FSS ADDRESS SPACE.
S02D - THE ,ES) MAIN TASK WAS ABENDED BY THE OPERATOR OR A
CATASTROPHIC ERROR.
S030 - DURING A BISAM OR 'ISAM OPEN DCBMACRF DID NOT INDICATE A
VALID MODE OF OPERATION.
S031 - SPACE RE'UESTED NOT AVAILABLE, DECREASE THE SPACE
ALLOCATION
S032 - DURING A BISAM OR 'ISAM OPEN DCBMACRF WAS NOT VALID FOR
ISAM.
S03B - ISAM DATASET TO BE PROCESSED, BUT NOT CREATED OR ITS DCB
NOT CLOSED AFTER CREATION.
POSSIBLE CAUSE
- DATASET WAS TO BE WRITTEN ON BUT WAS OPENED AS INPUT
- LRECL/BLKSI$E PROBLEM EXISTS - INVALID VALUES OR NOT MULTIPLES
S03D - THE ERROR OCCURRED DURING THE EXECUTION OF A 'ISAM OR
BISAM OR BDAM MACRO INSTRUCTION.
- IF THE REGISTER 15 RETURN CODE IS AVAILABLE, SUPPLY IT IN THE S%D
OPERAND FOR MORE SPECIFIC INFORMATION! H ABEND O"S%D-RC#
S03D - 04 - AN OPEN MACRO WAS ISSUED FOR AN INDEXED SE'UENTIAL OR
DIRECT DATASET. THE VOLUME SERIAL NUMBERS ON THE DD STATEMENT
WERE NOT SPECIFIED IN THE SAME ORDER THAT THE DATASET WAS
CREATED.
S03D - 08 - AN OPEN MACRO WAS ISSUED FOR AN INDEXED SE'UENTIAL
DATASET. THE FIRST VOLUME OF THE DATASET DOE NOT HAVE A FORMAT)
DSCB.
S03D - 0C - AN OPEN MACRO WAS ISSUED FOR A DIRECT DATASET. THE
DATASET HAS AN INDEXED SE'UENTIAL ORGANI$ATION.
S046 - SORT CAPACITY EXCEEDED
S047 - AN UNAUTHORI$ED PROGRAM RE'UESTED A RESTRICTED SVC.
S04B - AN INVALID OPERATION CODE WAS PASSED TO A TSO LINKAGE
ASSIST ROUTINE "LAR#.
S04B - 04 - THE LAR "IK,EFTSL# FOR THE TERMINAL MONITOR PROGRAM
"TMP# RECEIVED AN INVALID FUNCTION NUMBER.
S04B - 08 - THE SERVICE ROUTINE1S LAR "IK,TSLAR# WAS INVOKED AT
IK,TSLAR, WHICH IS AN INVALID SERVICE ROUTINE ENTRY POINT.
S04C - THE TERMINAL MONITOR PROGRAM "TMP# WAS INVOKED AT ENTRY
POINT IK,EFT1A AND THE TMP DETACHED A PROGRAM THAT COMPLETED
WITH A NON-$ERO COMPLETION CODE "WHICH IS IN REGISTER 15#.
S04E - INTERNAL IBM DATABASE ) "DB)# ERROR.
S04F - DB) ABNORMAL TERMINATION TO AVOID DATA INTEGRITY
PROBLEMS.
S052 - A PROGRAM MADE AN INVALID PC/AUTH RE'UEST. CHECK THE
CODE IN REGISTER 15.
S053 - A PROGRAM MADE A PC/AUTH RE'UEST BUT AN ERROR PREVENTED
NORMAL COMPLETION. CHECK THE CODE IN REGISTER 15.
S061 - I/O ERROR IN SORT EXEC, CHECK FOR DATA MESSAGES
S063 - SORTIN DATA PROBLEM
S064 - AN ADDRESS SPACE THAT HOLDS A CROSS MEMORY LOCAL LOCK
"CML LOCK# TERMINATED ABNORMALLY BEFORE IT FREED THE LOCK.
S66D - LIBRARY ACCESS PROBLEM. LOOKS THE SAME AS A S106 ABEND.
"LLA#
S071 - THE OPERATOR PRESSED THE RESTART KEY TO ACTIVATE THE
SYSTEM1S RECOVERY AND TERMINATION PROCESS. THE PROGRAM
RUNNING AT THE TIME THE OPERATOR PRESSED THE RESTART BUTTON
WAS SENT THROUGH
ABEND PROCESSING BECAUSE THE OPERATOR DETERMINED IT WAS IN A
NONCANCELABLE LOOP OR WAIT STATE.
S078 - RCT "REGION CONTROL TASK# PROCESSING HAS RECEIVED AN
UNACCEPTABLE RETURN CODE FROM AN INVOKED ROUTINE AND CANNOT
CONTINUE PROCESSING. RCT RECOVERY RECORDS THE ERROR IN
SYS1.LOGREC, PERFORMS RESOURCE CLEAN-UP, RE'UESTS A SYS1.DUMP
OF THE ADDRESS SPACE AND THEN RE'UESTS ADDRESS TERMINATION.
S079 - RCT "REGION CONTROL TASK# ATTENTION EXIT PROCESSING HAS
RECEIVED AN UNACCEPTABLE RETURN CODE FROM AN INVOKED
ROUTINE AND CANNOT CONTINUE PROCESSING. RCT RECOVERY RECORDS
THE ERROR IN
SYS1.LOGREC, PERFORMS RESOURCE CLEAN-UP, RE'UESTS A SYS1.DUMP
OF THE ADDRESS SPACE AND THEN RE'UESTS ADDRESS TERMINATION.
S07C - SUPERVISOR CONTROL RECOVERY HAS DETECTED AN ERROR
WHICH RE'UIRES THAT THE CURRENT TASK BE TERMINATED OR THAT THE
CURRENT ADDRESS SPACE BE TERMINATED.
S07F - DURING RECOVERY, VERIFICATION OF THE TCB 'UEUE ASSOCIATED
WITH THE TERMINATED ADDRESS SPACE RESULTED IN AN EMPTY TCB
'UEUE.
S0A7 - DURING $ NET,CANCEL COMMAND PROCESSING, VTAM FOUND THAT
A USER HAD NOT SPECIFIED A TPEND EXIT ROUTINE, OR VTAM COULD NOT
SCHEDULE A USER1S TPEXIT ROUTINE.
S0A8 - VTAM DETECTED AN ERROR DURING EXECUTION OF AN
APPLICATION PROGRAM. THE TWO LOW-ORDER BYTES OF REGISTER 15
CONTAIN A HEXADECIMAL REASON CODE.
- )11 - A VTAM VALIDITY CHECK OF THE USER1S RPL FAILED BECAUSE THE
RPL DOES NOT HAVE THE SAM PROTECTION KEY AS THE APPLICATION
PROGRAM1S TCB.
- &1 - THE USER1S RPL OR ECB IS INVALID.
S0A9 - EITHER A HALT NET,CANCEL COMMAND WAS ENTERED OR AN
ERROR OCCURRED DURING EXECUTION OF A VTAM MODULE. THE TWO
LOW-ORDER BYTES OF REGISTER-15 CONTAIN A HEXIDECIMAL REASON
CODE.
- - A HALT NET,CANCEL COMMAND HAS BEEN PROCESSED.
- 1F1 - THE ACF/VTAM STAE RETRY ROUTINE ISSUED AN ABEND A/ IN
ORDER TO GIVE CONTROL TO THE USER RECOVERY ROUTINE "STAE EXIT
ROUTINE#.
- %1 - THERE ARE NOT ENOUGH I/O BUFFERS TO SATISFY A VTAM
STORAGE RE'UEST.
- %111 - A VTAM MODULE FINISHED PROCESSING BEFORE IT RELEASED A
LOCK.
- %1-1 - A VTAM DESTINATION VECTOR TABLE "DVT# ENTRY IS INVALID FOR
THE DEFINED ATTACHMENT.
- &) - A VTAM RE'UEST FOR STORAGE FAILED
- &% - A VTAM RE'UEST TO RELEASE STORAGE FAILED BECAUSE THE
STORAGE HAD ALREADY BEEN RELEASED.
- &- - VTAM COULD NOT OBTAIN A LOCAL MEMORY LOCK.
- &/ - VTAM WAS UNABLE TO RESTORE ITS REGISTERS AFTER A USER
EXIT ROUTINE RETURNED CONTROL TO VTAM.
- &&1 - A RELSTORE WAS ISSUED FOR A PREVIOSLY FREED BUFFER.
- &1-1 - CONTROL CANNOT BE PASSED TO THE PROPER VTAM MODULE.
EITHER A VTAM DESTINATION VECTOR TABLE ENTRY IS INVALID FOR THE
DEFINED ATTACHMENT OR VTAM STOARGE HAS BEEN ALTERED.
S0AA - AN ABEND CONDITION OCCURRED DURING EXECUTION OF VTAM.
THE ERROR COULD NOT BE ASSOCIATED WITH ANY PARTICULAR TCB. ALL
TASKS IN THE ADDRESS SPACE ARE ABNORMALLY TERMINATED.
S0AE - IOS SUPPORT OF SYSTEM RESTART PROCESSING FOUND THAT THE
I/O PURGE MODULE "IGC1F# WAITING FOR THE COMPLETION OF AN I/O
RE'UEST. THE SYSTEM ABNORMALLY TERMINATES ALL TASKS IN THE
ADDRESS SPACE, THEN THE SYSTEM TERMINATES THE ADDRESS SPACE.
S0B0 - AN UNCORRECTABLE ERROR WAS DETECTED BY THE SWA
MANAGER. IF THE REGISTER 15 RETURN CODE IS AVAILABLE, SUPPLY IT IN
THE OPERAND FOR MORE SPECIFIC INFORMATION! H ABEND O"SB-RC#
S0B0 - 04 - INVALID FUNCTION RE'UESTED.
S0B0 - 08 - INVALID SVA "DOES NOT POINT TO THE BEGINNING OF A SWA
PREFIX OR THE SWA PREFIX HAS BEEN DESTROYED#.
S0B0 - 0C - ATTEMPTING TO READ A BLOCK NOT YET WRITTEN.
S0B0 - 10 - INVALID LENGTH " OR NEGATIVE FOR ASSIGN LOCATE OR
ATTEMPTING TO READ OR WRITE A RECORD, WHICH IS NOT 1&* BYTES, IN
MOVE MODE#.
S0B0 - 14 - INVALID COUNT FIELD " FOR READ, WRITE, ASSIGN OR FOR
WRITE AND ASSIGN#.
S0B0 - 18 - 'MNGRIO MACRO WAS ISSUED WITH BOTH OR NEITHER OF THE
READ AND WRITE BITS SET.
S0B0 - 1C - INVALID ID "THE CALLER ATTEMPTED TO WRITE A BLOCK FOR
THE FIRST TIME AND HAS EITHER PASSED A NON-EXISTING ID OR HAS
FAILED TO PASS ONE AND THE BLOCK DOES NOT HAVE AN IMBEDDED ID#.
S0B0 - 20 - INVALID BLOCK POINTER "WRITE LOCATE IS ATTEMPTING TO
WRITE AND IS PASSING A BLOCK POINTER WHICH IS NOT VALID FOR THE
SVA RE'UESTED#.
S0C1 - OPERATION EXCEPTION - AN OPERATION CODE IS NOT ON THE
MACHINE
POSSIBLE CAUSE
- SUBSCRIPT ERROR
- CLOBBERED CODE TRIED TO READ A FILE THAT WAS NOT OPEN
- MISSPELLED DDNAME
- ERROR IN PARAMETERS PASSED TO SUBROUTINES
- MISSING DD CARD
- RECORDING MODE WAS WRONG, OR DENSITY WAS INCORRECT
- BAD LOAD MODULE, POSSIBLE BAD OB,ECT DECK OR MISSING
SUBROUTINE
- FORTRAN - MISSING DIMENSION STATEMENT, SAME NAME FOR ARRAY
AND A SUBROUTINE
- COBOL - SUBROUTINE PROG ID WAS THE SAME AS THE ENTRY NAME
- COBOL - TRIED TO CALL WITHIN COBOL F SORT INPUT/OUTPUT
PROCEDURE
- COBOL - TRIED TO CALL A SUBROUTINE WHICH COULD NOT BE FOUND
- COBOL - INCOMPLETE DCB FOR SORTIN
- COBOL - USING SORT VERB, DDNAME WAS NOT SORTOUT WHEN THE
GIVING OPTION WAS USED.
- COBOL - EXECUTING SORT-USING AFTER OPENING SORTIN
S0C2 - PRIVILEGED OPERATION EXCEPTION
POSSIBLE CAUSE
- UNINTENTIONAL BRANCH TO INVALID INSTRUCTION DUE TO SUBSCRIPT
ERROR
- COBOL - MISSING PERIOD AT END OF PARAGRAPH OR PARAGRAPH NAMES
- MISSING GOBACK AFTER SORT VERB - LOGIC FELL INTO INPUT
PROCEDURE
- ACCEPT VERB EXECUTED WHEN NO SYSIN DD WAS AVAILABLE.
S0C3 - EXECUTION EXCEPTION - THE SUB,ECT INSTRUCTION OF EXECUTE
IS ANOTHER EXECUTE.
POSSIBLE CAUSE
- UNINTENTIONAL BRANCH, LOSS OF ADDRESSABILITY.
S0C4 - PROTECTION EXCEPTION - A VIRTUAL ADDRESS COULD NOT BE
TRANSLATED INTO A REAL ADDRESS.
POSSIBLE CAUSE
- ENTRY NOT FOUND
- INVALID ADDRESS WAS REFERENCED DUE TO SUBSCRIPT ERROR OR BAD
PARMS
- THE KEY OF AN INSTRUCTION OR AN OPERAND IN STORAGE DOES NOT
- MATCH THE PROTECTION KEY IN THE PSW "INTERRUPT CODE -#
- THE VIRTUAL SEGMENT OR PAGE WAS NEVER ALLOCATED "INTERRUPT
CODE 1 OR 11, RESPECTIVELY#
- THE PAGE WAS PAGED OUT AND THE ROUTINE RE'UESTING THE CODE
WAS DISABLED FOR I/O INTERRUPTS "INTERRUPT CODE 11#
- COBOL - IN GROUP MOVE, RECEIVING RECORD VARIABLE LENGTH
DEFINED WRONG
- TRIED MOVING VAR. LENGTH REC. LARGER THAN TARGET FIELD MAX
- TRIED TO READ OR WRITE A FILE WHICH WAS NOT OPEN
- USED DD DUMMY AND LOGIC SAYS AT END MOVE HIGH VALUES TO FD
- TRIED TO CALL WITHIN COBOL F SORT INPUT/OUTPUT PROCEDURE
- U WITH SORT - TRIED TO GOBACK IN THE OUTPUT PROCEDURE
S0C5 - ADDRESSING EXCEPTION - AN ADDRESS BEYOND THE AVAILABLE
REAL STORAGE WAS RE'UETED
POSSIBLE CAUSE
- SEE SC1 FOR MORE INFORMATION
- SUBSCRIPT ERROR - REFERENCED BEYOND TABLE IN PROGRAM RUNNING
V=R
- COBOL - PERFORMED PROCEDURE NOT EXITED PROPERLY
- RECORD DESCRIBED TOO SHORT
- REFERENCED A RECORD WITHOUT GIVING A READ
- TRIED TO USE WRITE WITHOUT FROM OPTION ON APPLY WRITE ONLY
FILE
S0C6 - SPECIFICATION EXCEPTION - AN INCORRECT BOUNDARY WAS
SPECIFIED. USUALLY CAUSED BY UNINTENTIONAL BRANCH TO INVALID
INSTRUCTION.
S0C7 - DATA EXCEPTION - DECIMAL DATA IS INCORRECT OR IMPROPERLY
OVERLAPPED OR NOT VALIDLY INITIALI$ED.
POSSIBLE CAUSE
- SUBSCRIPT ERROR, REFERENCED BEYOND TABLE
- COBOL - WORKING STORAGE NOT INITIALI$ED
- BAD DATA, SHOULD CHECK DATA FOR ERRORS
- GARBAGE IN A FIELD BEING TESTED OR DISPLAYED
- MOVE $EROES TO GROUP LEVEL IS DISPLAY, HAD SUBLEVELS THAT WERE
NOT
- PERIOD MISSING AFTER IMPERATIVE STATEMENTS WITHIN AT END
CLAUSE
- BINARY FIELD IN AN ARITHMETIC OPERATION IS NOT LARGE ENOUGH TO
ACCEPT RESULT "FOR MORE INFORMATION, SEE DESCRIPTION OF SC1#
S0C8 - FIXED POINT OVERFLOW EXCEPTION NOTE - MASKED BY FORTRAN
S0C9 - FIXED POINT DIVIDE EXCEPTION NOTE - MASKED BY FORTRAN
S0CA - DECIMAL OVERFLOW EXCEPTION THE DESTINATION FIELD IS TOO
SMALL TO CONTAIN THE RESULT FIELD
IN A DECIMAL OPERATION.
S0CB - DECIMAL DIVIDE EXCEPTION A 'UOTIENT EXCEEDS THE SPECIFIED
DATA FIELD SI$E.
S0CC - EXPONENT OVERFLOW EXCEPTION A FLOATING POINT NUMBER
EXCEEDS THE MAXIMUM SI$E.
NOTE - THIS ERROR IS DETECTED AND FIXED IN FORTRAN
S0CD - EXPONENT UNDERFLOW EXCEPTION A FLOATING POINT NUMBER IS
SMALLER THAN THE MINIMUM.
NOTE - FORTRAN WILL SET THE RESULT TO $ERO AND CONTINUE
PROCESSING
S0CE - SIGNIFICANCE EXCEPTION A FLOATING POINT ADDITION OR
SUBTRACTION RESULTS IN AN ALL $ERO
FRACTION
NOTE - THIS IS MASKED IN FORTRAN
S0CF - FLOATING POINT DIVIDE EXCEPTION - DIVIDE BY $ERO
NOTE - THIS ERROR IS DETECTED AND NOTED BY FORTRAN
S0D2 - A PROGRAM CHECK WAS DETECTED. AN INTERRUPTION CODE OF 1+
X11)1 "TRANSLATION SPECIFICATION EXCEPTION# HAS OCCURRED. THERE
IS INVALID DATA IN EITHER CONTROL REGISTERS $ERO OR ONE, OR A
SEGMENT OR PAGE TABLE. THE ERROR IS THE RESULT OF A HARDWARE
ERROR OR A PROGRAM RUNNING IN KEY $ERO HAS CAUSED DATA
DAMAGE.
S0D3 - A PROGRAM CHECK, INTERRUPTION CODE 1/ X11%1 "SPECIAL
OPERATION ERROR# HAS OCCURRED. A PRIVILEGED PROGRAM ISSUED A
SET SYSTEM MASK. THIS INSTRUCTION IS NOT VALID IN OS/VS) "SINCE
RELEASE )#.
S0D9 - A PROGRAM CHECK, INTERRUPTION CODE %+ "PAGE FAULT ASSIST
ERROR# HAS OCCURRED. EITHER A HARDWARE ERROR OCCURRED OR A
PROGRAM RUNNING IN KEY $ERO CAUSED DATA DAMAGE.
S0E0 - AN INVALID OR UNRECOGNI$ED PROGRAM INTERRRUPT OCCURRED.
POSSIBLE CAUSE
- THIS LEVEL OF MVS IS NOT THE CORRECT ONE FOR THE HARDWARE,
ESPECIALLY IF THE INTERRUPT CODE IS UNKNOWN.
S0E0 - 1D - A S'UARE ROOT EXECEPTION OCCURED.
S0E0 - 1E - AN UNNORMALI$ED OPERAND EXECEPTION OCCURED.
S0E0 - 28 - RESERVED BIT POSITIONS IN AN ALET WERE NON-$ERO.
S0E0 - 29 - AN ALET SPECIFIED AN INVALID ACCESS LIST ENTRY.
S0E0 - 2A - AN ALET SPECIFIED A PREVIOUSLY DELETED ACCESS LIST
ENTRY.
S0E0 - 2B - AN ACCESS LIST ENTRY SPECIFIED AN INVALID DATA SPACE.
S0E0 - 2C - THE SE'UENCE NUMBER IN THE ASTE THAT THE ACCESS LIST
ENTRY REFERS TO IS NOT E'UAL TO THE NUMBER IN THE ACCESS LIST
ENTRY.
S0E0 - 2D - A PRIVATE ACCESS LIST ENTRY IS SPECIFIED, AND THE CURRENT
EAX IS NOT AUTHORI$ED TO THE TARGET ADDRESS SPACE.
S0E0 - 30 - A STACKING INTRUCTION WAS ISSUED WHEN THE LINKAGE
STACK WAS FULL.
S0E0 - 31 - AN UNSTACKING INTRUCTION WAS ISSUED WHEN THE LINKAGE
STACK HAS NO STACK ENTRIES.
S0E0 - 32 - A LINKAGE STACK SPECIFICATION INTERRUPT OCCURED.
S0E0 - 33 - AN INVALID LINKAGE STACK ENTRY "LSE# TYPE WAS
ENCOUNTERED BY THE HARDWARE OR BY AN UNSTACKING OPERATION.
S0E0 - 34 - A PR INSTRUCTION WAS ISSUED AGAINST A LINKAGE STACK
ENTRY THAT HAS THE UNSTACK SUPPRESSION BIT SET. MVS SETS THIS BIT
IN A LINKAGE STACK ENTRY TO PREVENT SVC ROUTINES FROM
UNSTACKING
ENTRIES THEY DID NOT ADD TO THE STACK.
S0E1 - THE ERROR OCCURRED WHILE PROCESSING THE FIRST EXCP OF A
VIO DATASET. PLEASE REPORT THIS PROBLEM TO THE SYSTEMS GROUP.
S0E2 - THE ERROR OCCURRED WHILE PROCESSING THE FIRST EXCP OF A
VIO DATASET. THE SYSTEM WAS UNABLE TO ASSIGN, LOCATE, FIX, FREE,
OR ACCESS VIO PAGES FOR THE DATASET. PLEASE REPORT THIS PROBLEM
TO THE SYSTEMS GROUP.
S0E3 - THE ERROR OCCURRED WHILE PROCESSING A VIO DATASET. THE
SYSTEM WAS UNABLE TO ASSIGN, LOCATE, FIX, FREE, OR ACCESS VIO
PAGES FOR THE DATASET. PLEASE REPORT THIS PROBLEM TO THE
SYSTEMS GROUP.
S0E4 - THE ERROR OCCURRED WHILE TRYING TO SCRATCH A VIO DATASET.
PLEASE REPORT THIS PROBLEM TO THE SYSTEMS GROUP.
S0E5 - UNABLE TO DISCONNECT THE VIRTUAL TRACK BUFFER FORM THE
VIO DATASET. PLEASE REPORT THIS PROBLEM TO THE SYSTEMS GROUP.
S0E6 - UNABLE TO PROCESS A DATA SET THAT HAS ALREADY BEEN
SCRATCHED.
S0F0 - AN ERROR OCCURRED WHILE PROCESSING A MACHINE CHECK
INTERRUPTION. IN AN ATTEMPT TO RECOVER THE SYSTEM THE
INTERRUPTED TASK WAS TERMINATED.
S0F1 - PROGRAM INTERRUPTION IN I/O INTERRUPTION HANDLER RECORD
DESCRIBED AS WRONG LENGTH
S0F2 - I/O INTERRUPT PROCESSING ERROR. I/O RECOVERY ROUTINE
FAILED. CLOBBERED IOB OR OTHER SVC PARAMETERS - SEE SC1
S0F3 - MACHINE CHECK INTERRUPTION DISK I/O FAILURE OR MACHINE
TROUBLE
S0F8 - THE ISSUER OF AN SVC WAS EITHER IN SRB MODE, HELD A LOCK,
WAS DISABLED, OR WAS IN CROSS MEMORY MODE.
S0F8 - 04 - THE SVC ISSUER WAS NOT IN TCB MODE.
S0F8 - 08 - THE SVC ISSUER HELD A LOCK.
S0F8 - 0C - THE SVC ISSUER WAS DISABLED.
S0F8 - 10 - THE SVC ISSUER WAS IN CROSS MEMORY MODE.
S0F8 - 14 - THE SVC ISSUER HAD AN ENABLED UNLOCKED TASK MODE FRR.
IE. EUT=YES WAS SPECIFIED ON THE SETFRR MACRO.
S0F8 - 18 - THE SVC ISSUER WAS IN AR ADDRESS SPACE CONTROL MODE
FOR AN SVC WHICH DOES NOT ALLOW THIS.
S0F8 - 1C - THE SVC ISSUER WAS NOT AUTHORI$ED FOR SVC MICROCODE
ASSIST.
S0F9 - THE ERROR OCCURRED WHILE TRYING TO AC'UIRE OR RELEASE AN
SVRB.
S0F9 - 00- LS'A HAS BEEN EXHAUSTED AND AN SVRB CANNOT BE
CREATED TO HONOUR AN SVC RE'UEST IN THE ADDRESS SPACE.
S0F9 - 04 - AN SVRB BEING FREED MAY NOT BELONG TO THE SVRB POOL.
S0FB - A TRANSLATION EXCEPTION HAS OCCURRED. INVALID CONTENTS
WERE DETECTED IN CONTROL REGISTER .
S0FC - A TRANSLATION ERROR OCCURRED WHILE REFERENCING DATA NOT
IN THE HOME ADDRESS SPACE. BAD DAT TABLES OR WRONG STO ADDRESS.
S0FD - A TYPE * SVC RE'UESTED THE SVC FIRST LEVEL INTERRUPT
HANDLER "FLIH# TO SCHEDULE A CROSS MEMORY SRB. T*EXIT MACRO
POINTS TO SRB WHERE SRBASCB IS NOT HOME ASCB.
S0FE - AN ERROR WAS DETECTED WHILE RMF WAS SAMPLING DATA ABOUT
THE STATE OF THE SYSTEM.
S100 - I/O INTERBLOCK GAP DETECTED WHEN WRITING RECORD
S101 - DURING EXECUTION OF A WAIT MACRO, THE PROBLEM PROGRAM
SPECIFIED MORE EVENTS THAN THERE WERE ECBS.
S102 - THE ERROR OCCURRED DURING EXECUTION OF A POST MACRO
INSTRUCTION. THE CONTROL PROGRAM FOUND AN INVALID EVENT
CONTROL BLOCK ADDRESS, OR THE ECB WAS IN A STORAGE AREA WITH A
PROTECTION KEY DIFFERENT FROM THAT OF THE TASK ISSUING THE
MACRO.
S102 - 00 - INVALID ECB FOR POST IN THE USER1S KEY.
S102 - 04 - INVALID ECB FOR AN XMPOST "CROSS MEMORY POST#.
S102 - 08 - INVALID ECB FOR BRANCH ENTRY POST IN THE USER1S KEY.
S102 - 0C - INVALID ECB FOR BRANCH ENTRY XMPOST.
S104 - GETMAIN ERROR. AN AUTHORI$ED PROGRAM RE'UESTED VIRTUAL
STORAGE THAT RE'UIRES MORE REAL STORAGE THAN IS AVAILABLE.
S104 - 04 - NOT ENOUGH REAL STORAGE FOR SPACE IN S'A SUBPOOL.
S104 - 08 - NOT ENOUGH REAL STORAGE FOR SPACE IN FIXED CSA
SUBPOOL.
S104 - 0C - NOT ENOUGH REAL STORAGE FOR SPACE IN LS'A SUBPOOL.
S104 - 1C - LS'A RE'UEST FAILED - PAGE TABLE PAGED OUT.
S104 - 20 - AUTHORI$ED PRIVATE RE'UEST FAILED - PAGE TABLE PAGED
OUT.
S106 - CAN1T FIND IBM SUBTOUTINE. RECOMPILE AND RERUN. AN ERROR
WAS DETECTED BY THE CONTROL PROGRAM WHEN IT ATTEMPTED TO
FETCH THE RE'UESTED PROGRAM INTO VIRTUAL STORAGE.
POSSIBLE CAUSE
- PREVIOUS LKED STEP FAILED TO OUTPUT A SYSLMOD, NEEDS LARGER
SI$E= I/O ERROR - MACHINE TROUBLE OR DISK FAILURE
S106-D - INVALID RECORD TYPE IN LOAD MODULE
S106 - 0E - THE CONTROL PROGRAM FOUND AN INVALID ADDRESS IN THE
LOAD MODULE. CHECK REGISTER !
- ) - ERROR CONVERTING TTR.
- )- - BLOCK IS OUTSIDE OF THE MODULE.
- )+ - AN ADCON LOCATION IS INVALID.
S106-F - UNCORRECTABLE I/O ERROR WHEN LOADING MODULE.
S106 - 10 - THE CONTROL PROGRAM DETECTED A RELOCATION ERROR IN
THE LOAD MODULE.
S10A - GETMAIN ERROR. A PROGRAM RE'UESTED VIRTUAL STORAGE THAT
RE'UIRES MORE REAL STORAGE THAN IS AVAILABLE.
S10A - 04 - NOT ENOUGH REAL STORAGE FOR SPACE IN S'A SUBPOOL.
S10A - 08 - NOT ENOUGH REAL STORAGE FOR SPACE IN FIXED CSA
SUBPOOL.
S10A - 0C - NOT ENOUGH REAL STORAGE FOR SPACE IN LS'A SUBPOOL.
S10A - 1C - LS'A RE'UEST FAILED - PAGE TABLE PAGED OUT.
S10A - 20 - AUTHORI$ED PRIVATE RE'UEST FAILED - PAGE TABLE PAGED
OUT.
S10B - TIME SERVICE ROUTINE ERROR - ERROR IN INPUT PARAMETERS.
S10D- ,OBSTEP TASK ABENDED WHEN A SUBTASK THAT IS ALSO A ,OBSTEP
TASK IS IN STEP-MUST-COMPLETE STATUS.
S10E - SPIE MACRO ERROR. THE PICA ADDRESS IS INVALID.
S112 - INVALID INPUT WAS PASSED TO SVC 1+ BY THE BLDL OR FIND
MACRO. RE'UIRES MORE REAL STORAGE THAN IS AVAILABLE.
POSSIBLE CAUSE!
THE DCB HAS BEEN OVERLAID, ESPECIALLY DCBDEBAD OR DCBPOINT.
S112 - 01 - PARAMETER LIST NOT IN CALLER1S STORAGE.
S112 - 02 - DCB NOT IN CALLER1S STORAGE.
S112 - 03 - DCB DOES NOT POINT TO A VALID DEB.
S112 - 04 - PROGRAM CHECK OCCURRED IN THE POINT ROUTINE.
S112 - 13 - DCB DOES NOT POINT TO A VALID DEB. DCB DUMPED TO GTF.
S112 - 14 - PROGRAM CHECK OCCURRED IN THE POINT ROUTINE. THE DCB
IS DUMPED TO THE GTF DATA SET.
S113 - AN ERROR OCCURRED DURING AN OPEN WITH A TYPE=, OPERAND.
S113 - 08 - A ,FCB EXTENSION BLOCK WAS NEEDED FOR PROCESSING A
PHYSICAL SE'UENTIAL DATA SET BUT NONE WAS AVAILABLE.
S113 - 0C - AN OPEN TYPE=, WAS ISSUED, BUT NO ,FCB EXIT WAS FOUND IN
THE DCB EXIT LIST. SPECIFY A ,FCB EXIT, SUPPLY THE ,FCB.
S113 - 18 - A ,FCB EXTENSION BLOCK WAS NEEDED FOR PROCESSING A
DIRECT OR INDEX SE'UENTIAL DATA SET.
S113 - 20 - END-OF-VOLUME ENCOUNTERED FOR A VSAM DATA SET. MULTI-
VOLUME VSAM FILES CANNOT BE OPENED WITH A DCB.
S113 - 24 - OPEN ISSUED TO A MULTI-VOLUME VSAM DATA SET. MULTI-
VOLUME VSAM FILES CANNOT BE OPENED WITH A DCB.
S113 - 28 - OPEN ATTEMPT FOR CONCATENATED VSAM USING A DCB.
S113 - 2C - OPEN ATTEMPT FOR VSAM USING A DCB WHEN THE CALLER WAS
NOT APF AUTHORI$ED OR IN SUPERVISOR STATE.
S113 - 30 - INVALID ,CL DISPOSITION DETECTED FOR VSAM OPENED WITH A
DCB. ONLY ALLOWED "OLD,KEEP,KEEP# OR "SHR,KEEP,KEEP#.
S113 - 34 - AN UNSUPPORTED DCB OPTION WAS SPECIFIED FOR A VSAM
DATA SET OPENED WITH A DCB. ONLY VALID OPTIONS ARE INPUT AND
UPDAT.
S113 - 38 - AN OPEN WAS ISSUED FOR A VSAM DATA SET WITH A DCB, BUT
THE VTOC DOES NOT INDICATE THAT IT IS A VSAM DATA SET.
S115 - SVC )1 "STOW# ERROR. THE DCB DID NOT POINT TO A VALID DEB, OR
THE DEB DID NOT POINT BACK TO THE DCB.
S117 - AN I/O ERROR OCCURRED DURING A BSAM CLOSE TYPE=T MACRO.
S118 - INVALID PARAMETERS WERE PASSED TO DEVTYPE "SVC )-#. IF THE
REGISTER 15 RETURN CODE IS AVAILABLE, SUPPLY IT IN THE S118
OPERAND FOR MORE SPECIFIC INFORMATION! H ABEND O"S11+-RC#
S118 - 01 - THE DDNAME "ADDRESS IN GPR 1# WAS NOT IN CALLER1S
REGION.
S118 - 02 - OUTPUT AREA "ADDRESS IN GPR # WAS NOT IN CALLER1S
REGION.
S11A - A PROTECTION CHECK OCCURRED WHEN THE SYSTEM TRIED TO
STORE INTO A USER SUPPLIED OS/VS CAMLST WORK AREA.
S121 - A MODULE ISSUED SVC %% "IOHALT# WITH THE LOW ORDER BIT OF
GPR1 OFF, WHICH INDICATES THE PRE-XA ")-BYTE UCB ADDR# INTERFACE.
S122 - EITHER THE OPERATOR OR THE ,OB ENTRY SUBSYSTEM CANCELLED
THE ,OB, RE'UESTING A DUMP. CHECK THE ,OB LOG LISTING FOR MORE
INFO.
S128 - AN INVALID ADDRESS LIST WAS SPECIFIED FOR AN EXTRACT
MACRO. LIST NOT ON A FULLWORD BOUNDARY OR NOT IN ,OB STEP1S
STORAGE.
S12D - INVALID SEGMENT TABLE IN AN OVERLAY PROGRAM, SEE SC1.
S12E - ERROR FOUND IN INPUT PARAMETERS TO TTIMER SERVICE
ROUTINE.
S130 - THE DE' MACRO SPECIFIED A RESOURCE NOT PREVIOUSLY
SPECIFIED BY AN EN' MACRO. THAT IS, THE PROGRAM HAD NOT
RE'UESTED CONTROL
A RESOURCE IT WAS ATTEMPTING TO RELEASE.
S137 - I/O ERROR IN END OF VOLUME LABEL PROCESSING ON MAGNETIC
TAPE. IF THE REGISTER 15 RETURN CODE IS AVAILABLE, SUPPLY IT IN THE
S1%& OPERAND FOR MORE SPECIFIC INFORMATION! H ABEND O"S1%&-RC#
S137 - 04 - AN I/O ERROR OCCURRED WHILE WRITING AN END OF VOLUME
LABEL OR TAPE MARK.
S137 - 08 - AN I/O ERROR OCCURRED WHILE POSITIONING THE TAPE IN
PREPARATION FOR LABEL PROCESSING.
S137 - 0C - AN I/O ERROR OCCURRED READING A TRAILER LABEL FOR A
DATASET OPENED WITH THE INPUT OR INOUT OPTION, OR READING THE
HEADER LABEL FOR A DATASET OPENED WITH THE RDBACK OPTION.
S137 - 10 - AN I/O ERROR OCCURRED WHILE POSITIONING A MAGNETIC
TAPE AT THE END OF THE DATASET.
S137-14 - I/O ERROR READING HEADER LABELS FOR A DATASET
S137-18 - I/O ERROR WHILE POSITIONING A TAPE FOR THE FIRST DATA
RECORD
S137-10 - I/O ERROR WHILE POSITIONING A TAPE FOR THE END OF A
DATASET
S137-1C - AN INVALID TRAILER RECORD WAS READ DURING THE END-OF-
VOLUME
S137 - 20 - AN INVALID HEADER LABEL WAS READ DURING END OF
VOLUME.
S137 - 24 - A SPECIFIC VOLUME SERIAL NUMBER WAS SPECIFIED FOR THE
SECOND OR SUBSE'UENT VOLUME OF AN OUTPUT DATASET ON
MAGNETIC TAPE. DURING EOV PROCESSING, IT WAS DISCOVERED THAT
THE EXPIRATION DATE "FROM THE HDR1 LABEL OF THE FIRST DATASET
CURRENTLY ON THE SPECIFIED VOLUME# HAD NOT PASSED. WHEN
RE'UESTED TO SPECIFY WHETHER THE VOLUME COULD BE USED IN SPITE
OF THE EXPIRATION DATE, THE OPERATOR DID NOT REPLY 1U1. ASK THE
OPERATOR TO REPLY 1U1 OR SPECIFY ANOTHER VOLUME SERIAL.
S137 - 28 - THE OPERATOR REPLIED 1M1 "RE,ECT VOL1 LABEL REWRITE# TO
MESSAGE IEC&-A.
S137 - 2C - THE INPUT VOLUME CONTAINS AN ISCII/ASCII VOLUME LABEL
WITH A STANDARD VERSION LABEL THAT IS NOT 1 OR %.
S137 - 30 - A LABEL VIOLATED THE PUBLISHED STANDARD FOR THE LABEL,
AND THE LABEL VALIDATION EXIT RE'UESTED OPEN/EOV TO RE,ECT THE
VOLUME.
S137 - 38 - AN I/O ERROR OCCURRED WHILE PROCESSING A READ BLOCK ID
TO STABLISH THE TAPE POSITION.
S138 - THE ERROR OCCURRED DURING THE EXECUTION OF AN EN'
MACRO. TWO EN' MACROS WERE ISSUED FOR THE SAME RESOURCE IN
THE SAME TASK
WITHOUT AN INTERVENING DE' MACRO. THE SECOND EN' MACRO DID
NOT SPECIFY TEST, USE, OR HAVE IN ITS RET OPERAND.
S13E - THE TASK WHICH CREATED A SUBTASK HAS ISSUED A DETACH FOR
THAT SUBTASK, SPECIFYING STAE=NO, BEFORE THAT SUBTASK HAS
TERMINATED.
S14F - THE ROUTINE ATTEMPTED TO EXECUTE THE STATUS MACRO
INSTRUCTION FOR OTHER THAN THE STOP, STOP SYNCH, OR START
FUNCTION AND WAS NOT IN SUPERVISOR KEY "-&#.
S16E - THE CONTROL PROGRAM RE'UESTED THAT A DEBCHK FUNCTION
BE PERFORMED ON A DATA EXTENT BLOCK OBTAINED FROM THE DCB
PASSED BY THE PROGRAM. THAT FUNCTION COULD NOT BE COMPLETED.
IF THE REGISTER 15 RETURN CODE IS AVAILABLE, SUPPLY IT IN THE S1*E
OPERAND FOR MORE SPECIFIC INFORMATION! H ABEND O"S1*E-RC#
S16E - 04 - THE INDICATED DEB POINTER IS NOT IN THE DEB TABLE. A DEB
WHOSE ADDRESS IS NOT IN THE DEB TABLE CANNOT BE VERIFIED,
DELETED, OR PURGED
S16E - 08 - INVALID TYPE SPECIFIED "MACRO NOT ISSUED#. ACCEPTABLE
TYPES ARE ADD, DELETE, VERIFY, AND PURGE.
S16E - 10 - DEBDCBAD DOES NOT POINT TO DCB. IT IS NORMALLY ASSUMED
THAT THE DCBDEBAD FIELD OF THE DCB POINTES TO THE DEB, BUT THE
DEBDCBAD FIELD OF THE DEB MUST POINT TO THE DCB WHEN
TYPE=VERIFY, ADD, OR DELETE.
S16E - 14 - AM VALUE DOES NOT E'UAL DEBAMTYP VALUE. WHEN A DEB
POINTER IS ADDED TO THE TABLE, THE ACCESS METHOD POINTER "AM#
VALUE, IF
GIVEN IS PLACED IN THE DEBAMTYP FIELD OF THE DEB. IF NO AM VALUE
IS CODED, A IS INSERTED IN THE FIELD. SUBSE'UENT DEBCHKS ISSUED
TO VERIFY OR DELETE THAT DEB POINTER MUST EITHER SPECIFY THE
SAME AM VALUE OR OMIT THE OPERAND. WHEN THE OPERAND IS
OMITTED, NO COMPARISON IS MADE.
S16E - 18 - DEB NOT ON TCB CHAIN FOR TYPE = ADD. BEFORE THE DEB
POINTER CAN BE ADDED TO THE TABLE, THE DEB ITSELF MUST BE
'UEUED ON THE CURRENT TCB DEB CHAIN.
S16E - 1C - DEBAMTYP OR DEBTBLOF = FOR TYPE = ADD. VALUES OTHER
THAN INDICATE A POINETR TO THIS DEB ALREADY EXISTS IN THE DEB
TABLE.
S16E - 20 - DEB TABLE CONTAINS %)&* BYTES AND TYPE = ADD. THE
CURRENT DEB TABLE DOES NOT HAVE SPACE FOR THIS NEW DEB POINTER.
TO
INCREASE THE TABLE SI$E BY THE RE'UIRED INCREMENT OF )- WOULD
CAUSE THE TABLE TO EXCEED ITS MAXIMUM SI$E.
S171 - THE REAL STORAGE MANAGER WAS INVOKED WITH A RE'UEST FOR
A PGFIX, PGFREE, PGLOAD, OR PGOUT SERVICE AND THE RE'UEST WAS
ILLEGAL OR INVALID. THE RE'UEST IS CONSIDERED TO BE ILLEGAL IF THE
STORAGE RANGE SPECIFIED BY THE INPUT PARAMETERS DOES NOT EXIST
"A GETMAIN WAS NOT ISSUED FOR IT#.
NOTE! THE MEANINGS OF THE CONTENTS OF GENERAL REGISTERS 11, 1),
1%, AND 1- ARE PROVIDED FOR DIAGNOSTIC PURPOSES IN THE FULL
DESCRIPTION OF THIS ABEND IN THE SYSTEM CODES MANUAL. IF THE
REGISTER 15 RETURN CODE IS AVAILABLE, SUPPLY IT IN THE S1&1
OPERAND FOR MORE SPECIFIC INFORMATION! H ABEND O"S1&1-RC#
POSSIBLE CAUSE!
INPUT PARAMETER ERROR IN VIRTUAL SUBAREA LIST "VSL#!
- VSL NOT ON A FULLWORD BOUNDARY.
- VSL NOT IN FIXED STORAGE.
- UNDEFINED OR CONFLICTING OPTION FLAGS. END ADDRESS OF RANGE
NOT GREATER THAN BEGINNING ADDRESS. AN OPTION WAS SPECIFIED
WHICH IS NOT SUPPORTED BY MVS. THESE ARE RSAOPT AND ECBIND.
- VSL IS STORE PROTECTE FROM THE CALLER.
INPUT PARAMETER ERROR ON ECB!
- ECB NOT ON FULLWORD BOUNDARY.
- ECB IS STORE-PROTECTED FROM CALLER.
- ECB NOT SPECIFIED FOR PGFIX.
- ECB SPECIFIED FOR PGOUT.
S171 - 04 - THE ERROR WAS DETECTED BY THE PAGE SERVICES ROUTINE.
THIS GENERALLY INDICATES THAT THE CALLER DID NOT OWN THE
VIRTUAL
STORAGE DEFINED BY THE VSL LIST ENTRY.
S171 - 16 - THE INPUT VSL OR ECB FAILED TO PASS THE PAGE SERVICES
INTERFACE VALIDITY CHECK.
S178 - GETMAIN ERROR. AN AUTHORI$ED PROGRAM RE'UESTED VIRTUAL
STORAGE THAT RE'UIRES MORE REAL STORAGE THAN IS AVAILABLE. IF
THE REGISTER 15 RETURN CODE IS AVAILABLE, SUPPLY IT IN THE S1&+
OPERAND FOR MORE SPECIFIC INFORMATION! H ABEND O"S1&+-RC#((
S178 - 04 - NOT ENOUGH REAL STORAGE FOR SPACE IN S'A SUBPOOL.
S178 - 08 - NOT ENOUGH REAL STORAGE FOR SPACE IN FIXED CSA
SUBPOOL.
S178 - 0C - NOT ENOUGH REAL STORAGE FOR SPACE IN LS'A SUBPOOL.
S178 - 1C - LS'A RE'UEST FAILED - PAGE TABLE PAGED OUT.
S178 - 20 - AUTHORI$ED PRIVATE RE'UEST FAILED - PAGE TABLE PAGED
OUT.
S201 - THE WAIT MACRO EXPANSION CONTAINED AN INVALID EVENT
CONTROL BLOCK "ECB# ADDRESS OR THE PROGRAM IS NOT IN THE SAME
KEY AS THE ECB.
S202 - THE POST MACRO INSTRUCTION ENCOUNTERED AN ERROR WHILE
PROCESSING AN EVENT CONTROL BLOCK "ECB#. IF THE REGISTER 15
RETURN CODE IS AVAILABLE, SUPPLY IT IN THE S)) OPERAND FOR MORE
SPECIFIC INFORMATION! H ABEND O"S))-RC#((
S202 - 00 - THE CONTROL PROGRAM FOUND AN INVALID RE'UEST BLOCK
"RB# ADDRESS IN THE % LOW-ORDER BYTES OF THE ECB SPECIFIED IN A
WAIT
MACRO. THE RB ADDRESS MUST REMAIN IN THE ECB UNTIL A POST IS
ISSUED.
S202 - 04 - THE WAITING RB IS NOT ENABLED FOR INTERRUPTS.
S202 - 08 - FOR A POST IN A USER KEY AND A WAIT IN A SYSTEM KEY, THE
ECB TO BE POSTED DOES NOT MATCH ANY ECB BEING WAITED ON.
S202 - 0C - FOR A WAIT IN A USER KEY, THE ECB ADDRESS IS INVALID.
S204 - 00 - " IS THE ONLY POSSIBLE RETURN CODE ASSOCIATED WITH
S)-# GETMAIN ERROR. NOT ENOUGH REAL STORAGE AVAILABLE TO BACK
A MINIMUM NUMBER OF VSM CELLS "IN LS'A# DURING LOCAL CELL POOL
EXPANSION.
S205 - 00 - " IS THE ONLY POSSIBLE RETURN CODE ASSOCIATED WITH
S)5#GETMAIN ERROR. NOT ENOUGH REAL STORAGE AVAILABLE TO BACK
A MINIMUM NUMBER OF VSM CELLS "IN LS'A# DURING LOCAL CELL POOL
EXPANSION.
S206 - THE ADDRESS OF THE PARAMETER LIST, OR ONE OF THE
PARAMETERS PASSED TO A LINK, LOAD, XCTL, OR DELETE MACRO WAS
INVALID.
S20A - 00 - " IS THE ONLY POSSIBLE RETURN CODE ASSOCIATED WITH
S)A# GETMAIN ERROR. NOT ENOUGH REAL STORAGE AVAILABLE TO BACK
A MINIMUM NUMBER OF VSM CELLS "IN LS'A# DURING LOCAL CELL POOL
EXPANSION.
S213 - DSCB NOT FOUND. I/O ERROR IN READING OR WRITING DSCB. IF THE
REGISTER 15 RETURN CODE IS AVAILABLE, SUPPLY IT IN THE S)1%
OPERAND FOR MORE SPECIFIC INFORMATION! H ABEND O"S)1%-RC#
POSSIBLE CAUSE!
THE DATA SET IS NOT ON THE SPECIFIED VOLUME
DISP = MOD IS NOT COMPATIBLE WITH A VOLUME REFERENCE
INCORRECT TAPE POSITIONING
S213-04 - I/O ERROR WRITTEN IN THE DCB OF A DATAET
S213-08 - DATASET NOT FOUND ON VOLUME
S04E - RESOURCE UNAVAILABLE, CONTENTION, BAD INPUT, COULD BE
ANYTHING READ SYSTEM MESSAGE CODE AND REASON CODE
S213-04 - I/O ERROR WRITING DCB OF A DATASET
S213 - 08 - AN OPEN MACRO WAS ISSUED FOR A PASSWORD PROTECTED
DATASET BUT THE SYSTEM WAS UNABLE TO LOCATE THE PASSWORD
DATASET.
S213 - 0C - AN I/O ERROR OCCURRED READING A FORMAT-1 DSCB FOR A
DIRECT OR INDEXED SE'UENTIAL DATASET, OR THE FORMAT-1 DSCB
COULD NOT BE FOUND ON THE VOLUME SPECIFIED BY THE DD
STATEMENT.
S213-18 - DATASET NOT FOUND ON VOLUME
S213 - 18 - AN I/O ERROR OCCURRED WRITING BACK A FORMAT-1 DSCB.
S213 - 20 - DURING AN OPEN, A VOLUME CONTAINED MORE THAN 1*
EXTENTS OF THE INDICATED DATASET. GOOD LUCK FIGURING THIS ONE
OUT6
"SAM ACCESS OF AN ICF VSAM COMPONENT, PERHAPS2#
S213 - 24 - DURING AN OPEN, A VOLUME HAD A TYPE OF SPLIT CYLINDER
ALLOCATION NOT SUPPORTED UNDER OS. POSSIBLE DOS VOLUME.
S213 - 28 - AN OPEN MACRO WAS ISSUED FOR A DIRECT ACCESS DATASET
SPECIFING UNIT=SYSDA, BUT THE UNIT ALREADY CONTAINED 1)& USERS,
WHICH IS THE MAXIMUM NUMBER ALLOWED.
S213 - 2C - THE FORMAT-1 DSCB NOT FOUND INSTALLATION EXIT MODULE
ENCOUNTERED AN ERROR.
S213 - 30 - AN ATTEMPT WAS MADE TO OPEN A PDS FOR OUTPUT,DISP=SHR.
THE PDS IS ALREADY OPEN IN THIS CONDITION.
S213 - 38 - WHEN OPENING A PDSE THE KEYLENGTH WAS NOT $ERO "#, OR
THE KEYLENGTH WAS NOT $ERO "# OR EIGHT "+# FOR DIRECTORY INPUT.
S213 - 3C - WHEN OPENING A PDSE THE RECFM IN THE DCB WAS DIFFERENT
FROM THE RECFM ALREADY IN THE FORMAT-1 DSCB IN THE VTOC.
S213 - 40 - WHEN OPENING A PDSE, MACRF="E# WAS SPECIFIED. ACCESS OF A
PDSE BY EXCP IS NOT SUPPORTED.
S213 - 48 - OPEN DETECTED A BAD RETURN CODE FROM THE EXTENDED
CACHE ATTRIBUTE FACILITY.
S213 - 4C - WHEN OPENING A PDSE DSORG=PS WAS SPECIFIED, BUT NO
MEMBER WAS SPECIFIED.
S213 - 50 - OPEN DETECTED AN ERROR RETURN CODE FROM AN SMS
SERVICE WHILE PROCESSING A PDSE.
S213 - 58 - AN ATTEMPT WAS MADE TO CHANGE THE DSORG OF AN SMS-
MANAGED DATA SET TO UNMOVEABLE WHICH IS NOT ALLOWED ON SMS-
MANAGED VOLUMES.
S213 - 60 - OPEN DETECTED AN ERROR RETURN CODE FROM THE RESIDENT
CONVERT ROUTINE WHILE PROCESSING A PDSE DATA SET.
S213 - 64 - AN INCORRECT OPEN OPTION WAS SPECIFIED FOR A PDSE DATA
SET.
S213 - 68 - AN OPEN FOR A PDSE WAS ISSUED WITH RECFM=FB AND
LRECL=.
S213 - 6C - AN OPEN FOR A PDSE WAS ISSUED RE'UESTING 'SAM
UPDATEBUT LOCATE MODE WAS NOT SPECIFIED IN MACRF.
S213 - 70 - OPEN DETECTED A CROSS SYSTEM SHARE CONFLICT FOR THE
PDSE.
S214 - I/O ERROR IN TAPE POSITIONING OR VOLUME DISPOSITION. IF THE
REGISTER 15 RETURN CODE IS AVAILABLE, SUPPLY IT IN THE S)1-
OPERAND FOR MORE SPECIFIC INFORMATION! H ABEND O"S)1--RC#
S214-04 - I/O ERROR READING A USER LABEL ON A TAPE
S214-08 - I/O ERROR
S214-0C - E'C - I/O ERROR ON TAPE DRIVE
S214 - 10 - THE NUMBER OF BLOCKS PROCESSED ACCORDING TO THE TAPE
POSITION DOES NOT MATCH THE DCB BLOCK COUNT.
S222 - ,OB CANCELLED
S233 - INVALID PARAMETERS HAVE BEEN PASSED TO SVC DUMP. IF THE
REGISTER 15 RETURN CODE IS AVAILABLE, SUPPLY IT IN THE S)%%
OPERAND FOR MORE SPECIFIC INFORMATION! H ABEND O"S)%%-RC#
S233 - 04 - THE ADDRESS OF THE PARAMETER LIST IS $ERO.
S233 - 08 - THE PARAMETER LIST IS NOT A VALID SVC DUMP OR SNAP
PARAMETER LIST FOR MVS.
S233 - 0C - THE CALLER-SUPPLIED DATASET IS ON AN UNSUPPORTED
DEVICE.
S233 - 10 - IN A USER-SUPPLIED STORAGE RANGE, THE START ADDRESS IS
GREATER THAN THE END ADDRESS.
S233 - 14 - THE USER-SUPPLIED DATA "FOR HDR= OR HDRAD=# IS GREATER
THAN 1 CHARACTERS.
S233 - 18 - THE -K S'A BUFFER HAS BEEN RE'UESTED "BUFFER=YES# BUT
IT IS NOT SERIALI$ED "BY SETTING ON THE HIGH ORDER BIT IN CVTSDBF#
S233 - 1C - THE PARAMETER LIST OR WHAT IT POINTS TO IS IN THE -K S'A
BUFFER.
S233 - 20 - THE USER SUPPLIED A DCB ADDRESS AND THE DCB IS NOT OPEN,
OR THE DCB ADDRESS IS INVALID.
S233 - 24 - THE SPECIFIED ASID PARAMETER WAS SYNTACTICALLY INVALID.
THE ASID WAS LESS THAN $ERO, OR GREATER THAN THE MAXIMUM
VALUE.
S233 - 28 - AN ASID SPECIFIED IN THE ASID LIST POINTED TO BY THE
ASIDLST PARAMETER WAS SYNTACTICALLY INVALID. THE ASID WAS LESS
THAN $ERO, OR GREATER THAN THE MAXIMUM VALUE.
S233 - 2C - THE ASIDLST ADDRESS IS $ERO, OR POINTS TO AN AREA THAT
THE USER CANNOT REFERENCE.
S233 - 38 - THE CALLER SPECIFIED THE -K S'A BUFFER "BUFFER=YES# BUT
AN SVC DUMP WAS ALREADY IN PROGRESS.
S237 - THE ERROR OCCURRED DURING END-OF-VOLUME LABEL
VERIFICATION. IF THE REGISTER 15 RETURN CODE IS AVAILABLE, SUPPLY
IT IN THE S)%& OPERAND FOR MORE SPECIFIC INFORMATION! H ABEND
O"S)%&-RC#
POSSIBLE CAUSE!
INCORRECT VOLUME SERIAL
INCORRECT VOLUME MOUNTED
INCORRECT LABELS
S237-04 - HARDWARE ERROR - BLOCK OF DATA MISSED OR SKIPPED
S237-08 - DSN ON HEADER LABEL DOESN1T MATCH VOLUME SERIAL
S237-567 - HARDWARE ERROR. THE BLOCK COUNT DOES NOT MATCH
TRAILER LABEL
S237 - 0C - THE NUMBER OF BLOCKS PROCESSED, WHICH IS DETERMINED
BY THE POSITION OF THE TAPE, DOES NOT MATCH THE DCB BLOCK COUNT.
S23E - THE ERROR WAS DETECTED DURING EXECUTION OF A DETACH
MACRO INSTRUCTION. EITHER 1# THE PARAMETER PASSED TO DETACH IN
REGISTER
1 WAS NOT A FULLWORD ADDRESS, )# THE STORAGE KEY OF THAT
ADDRESS DID NOT MATCH THAT OF THE ISSUER OF THE DETACH, OR %# THE
PARAMETER CONTAINED IN THE ADDRESSED FULLWORD OF THE ISSUER
WAS NOT THE ADDRESS OF A SUBTASK OF THE ISSUER OF THE DETACH.
S240 - AN ERROR OCCURRED DURING EXECUTION OF A RD,FCB MACRO. IF
THE REGISTER 15 RETURN CODE IS AVAILABLE, SUPPLY IT IN THE S)-
OPERAND FOR MORE SPECIFIC INFORMATION! H ABEND O"S)--RC#
S240 - 04 - A RD,FCB MACRO INSTRUCTION WAS ISSUED, BUT THE DCB DID
NOT CONTAIN A FOUNDATION EXTENSION BLOCK.
S240 - 08 - A RD,FCB MACRO INSTRUCTION WAS ISSUED, BUT NO EXLST
ADDRESS WAS FOUND IN THE DCB.
S240 - 0C - A RD,FCB MACRO INSTRUCTION WAS ISSUED, BUT NO ,FCB EXIT
WAS SPECIFIED IN THE DCB EXIT LIST.
S240 - 10 - A RD,FCB MACRO INSTRUCTION WAS ISSUED, BUT THE ,FCB
BUFFER IS NOT WITHIN THE USER1S STORAGE.
S278 - 00 - " IS THE ONLY POSSIBLE RETURN CODE ASSOCIATED WITH
S)&+# GETMAIN ERROR. NOT ENOUGH REAL STORAGE AVAILABLE TO BACK
A MINIMUM NUMBER OF VSM CELLS "IN LS'A# DURING LOCAL CELL POOL
EXPANSION.
S2F3 - ,OB WAS BEING EXECUTED WHEN SYSTEM FAILURE OCCURRED - A
SYSTEM RESTART WAS PERFORMED
S300 - AN ERROR WAS DETECTED WHEN AN I/O OPERATION WAS
RE'UESTED.
- EITHER THE IOBM FIELD IN THE I/O BLOCK "IOB# IS HIGHER THAN THE
MAXIMUM EXTENT COUNT "DEBNMEXT# IN THE DATA EXTENT BLOCK
"DEB# OR THE STORAGE PROTECTION KEY OF THE DATA EXTENT BLOCK
WAS NOT $ERO OR THE DEB VALIDITY CHECK ROUTINE RETURNED TO
EXCP WITH A NON $ERO RETURN CODE. IN THE ABNORMAL TERMINATION
DUMP, THE TCB FIELD TCBEXCPD "AT OFFSET C# POINTS TO THE EXCP
PROBLEM DETERMINATION AREA. THE ITEMS IN THE PROBLEM
DETERMINATION AREA OF GREATEST INTEREST TO YOU ARE! "ALL
OFFSETS IN HEX#
- OFFSET 1 CONTAINS A COPY OF THE REGISTERS WHEN EXCP
DETERMINED THE ERROR CONDITION.
- OFFSET 5 CONTAINS THE CONTENTS OF THE RE'UEST 'UEUE ELEMENT
"R'E# IF ALLOCATED, WHEN THE PROGRAM CHECK OCCURRED.
POSSIBLE CAUSES OF A NON-$ERO RETURN CODE FROM IFGDEBCK ARE!
- THE DEBTABLE DOES NOT EXIST.
- THE DEBTBLOF VALUE IN THE DEB IS LESS THAN ONE OR GREATER THAN
THE NUMBER OF ENTRIES IN THE DEBTABLE.
- THE DEB ADDRESS FROM THE DCB DOES NOT MATCH ANY DEBTABLE
ENTRY.
S301 - AN ECB SPECIFIED IN A WAIT MACRO ALREADY HAD ITS WAIT FLAG
ON.
S305 - THE ERROR OCCURRED DURING EXECUTION OF A FREEMAIN
MACRO!
- THE SPECIFIED SUBPOOL COULD NOT BE FOUND.
- THE SP PARAMETER WAS SPECIFIED BUT THE VIRTUAL STORAGE AREA TO
BE RELEASED WAS NOT WITHIN THE SUBPOOL SPECIFIED.
- THE SP PARAMETER WAS NOT SPECIFIED BUT THE VIRTUAL STORAGE
AREA TO BE RELEASED WAS NOT WITHIN SUBPOOL $ERO.
- THE SP PARAMETER WAS SPECIFIED CORRECTLY, BUT THE BOUNDARIES
OF THE STORAGE AREAS TO BE FREED WERE NOT COMPLETELY
DESCRIBED BY A DESCRIPTOR 'UEUE ELEMENT.
- IF THE REGISTER 15 RETURN CODE IS AVAILABLE, SUPPLY IT IN THE S%5
OPERAND FOR MORE SPECIFIC INFORMATION! H ABEND O"S%5-RC#
S305 - 08 - S'A STORAGE IS NOT IN THE SUBPOOL SPECIFIED.
S305 - 0C - CSA STORAGE IS NOT IN THE SUBPOOL SPECIFIED.
S305 - 10 - LS'A STORAGE IS NOT IN THE SUBPOOL SPECIFIED.
S305 - 18 - PRIVATE AREA SUBPOOL NOT FOUND.
S305 - 1C - $ERO LENGTH WAS NOT SPECIFIED ON A SUBPOOL FREEMAIN.
S306 - INSUFFICIENT ACCESS AUTHORITY
S306 - 04 - THE RE'UESTED PROGRAM WAS NOT FOUND IN THE INDICATED
SOURCE. THAT IS, IT WAS FOUND IN AN UNAUTHORI$ED LIBRARY.
S306 - 08 - AN UNCORRECTABLE I/O ERROR OCCURRED WHEN THE
CONTROL PROGRAM ATTEMPTED TO SEARCH THE DIRECTORY OF THE
LIBRARY
CONTAINING THE MODULE, OR THE MODULE IS NOT RE-ENTRANT.
S306 - 0C - THE MODULE COULD NOT BE FOUND IN THE LPA OR IN THE LPA
DIRECTORY OR AN AUTHORI$ED LIBRARY.
S306 - 10 - A LOAD MACRO RE'UESTED A MODULE RE'UIRING PAGE
ALIGNMENT WITH GLOBAL="YES,F# SPECIFIED.
S306 - 20 - A ,OB STEP MODULE WAS FOUND IN AN UNAUTHORI$ED LNKLST
LIBRARY WHEN AN APF AUTHORI$ED MODULE WAS RE'UIRED.
S306 - 24 - AN AUTHORI$ED SERVICE ATTEMPTED TO ACCESS A NON-
REENTRANT LOAD MODULE WHICH WAS LOADED FROM AN AUTHORI$ED
LIBRARY BY AN UNAUTHORI$ED CALLER. ANOTHER COPY OF THE
MODULE COULD NOT BE FOUND.
S306 - 30 - THE USER WAS DENIED ACCESS TO THE PROGRAM BY THE
SYSTEM AUTHORI$ATION FACILITY.
S306 - 34 - THE USER ATTEMPTED TO USE A PROGRAM WHILE A PROGRAM-
ACCESSED DATA SET WAS OPEN.
S30A - THE ERROR OCCURRED DURING EXECUTION OF AN R-FORM
FREEMAIN MACRO FOR ONE OF THE FOLLOWING REASONS!
- A FREEMAIN FOR AN ENTIRE SUBPOOL WAS RE'UESTED "REGISTER 1 WAS
$ERO# BUT THE LENGTH IN REGISTER WAS NOT SET TO $ERO.
- THE SPECIFIED SUBPOOL COULD NOT BE FOUND.
- THE SP PARAMETER WAS SPECIFIED, BUT THE VIRTUAL STORAGE AREA
TO BE RELEASED WAS NOT WITHIN THE SUBPOOL SPECIFIED.
- THE SP PARAMETER WAS NOT SPECIFIED, BUT THE VIRTUAL STORAGE
AREA TO BE RELEASED WAS NOT WITHIN SUBPOOL $ERO.
- THE SP PARAMETER WAS SPECIFIED CORRECTLY, BUT THE BOUNDARIES
OF THE STORAGE AREAS TO BE FREED WERE NOT COMPLETELY
DESCRIBED BY A DECSRIPTOR 'UEUE ELEMENT "D'E#.
- IF THE REGISTER 15 RETURN CODE IS AVAILABLE, SUPPLY IT IN THE S%A
OPERAND FOR MORE SPECIFIC INFORMATION! H ABEND O"S%A-RC#
S30A - 08 - S'A STORAGE IS NOT IN THE SUBPOOL SPECIFIED.
S30A - 0C - CSA STORAGE IS NOT IN THE SUBPOOL SPECIFIED.
S30A - 10 - LS'A STORAGE IS NOT IN THE SUBPOOL SPECIFIED.
S30A - 14 - PRIVATE STORAGE IS NOT IN THE SUBPOOL SPECIFIED.
S30A - 18 - PRIVATE AREA SUBPOOL NOT FOUND.
S30A - 1C - $ERO LENGTH WAS NOT SPECIFIED ON A SUBPOOL FREEMAIN.
S30A - 20 - FOR A CSA STORAGE FREEMAIN, THE AREA TO BE FREED IS
LARGER THAN WAS SPECIFIED ON THE ORIGINAL GETMAIN, OR THE
FREEMAIN START ADDRESS IS NOT VALID.
S30A - 24 - FOR A PRIVATE STORAGE FREEMAIN, THE AREA TO BE FREED IS
LARGER THAN WAS SPECIFIED ON THE ORIGINAL GETMAIN, OR THE
FREEMAIN START ADDRESS IS NOT VALID.
S30E - BAD DATA"CHECK ONCODE#,CONTENTION
S311 - I/O ERROR READING HEADER LABELS FOR A DATASET
S313 - AN ABEND OCCURRED WHILE OPENING A DASD DATA SET BECAUSE
OF A VTOC I/O ERROR OR A SYSTEM LOGIC ERROR.
- IF THE REGISTER 15 RETURN CODE IS AVAILABLE, SUPPLY IT IN THE S%1%
OPERAND FOR MORE SPECIFIC INFORMATION! H ABEND O"S%1%-RC#
S313 - 04 - AN I/O ERROR OCCURRED READING A FORMAT-) OR FORMAT-%
DSCB DURING THE EXECUTION OF AN OPEN MACRO.
S313 - 08 - OPEN RECEIVED A NON-$ERO RETURN CODE FROM DASD
CALCULATION SERVICES "DCS# WHILE TRYING TO GET A SYSTEM-
DETERMINED BLOCKSI$E.
S314 - I/O ERROR IN READING DSCB
- IF THE REGISTER 15 RETURN CODE IS AVAILABLE, SUPPLY IT IN THE S%1-
OPERAND FOR MORE SPECIFIC INFORMATION! H ABEND O"S%1--RC#
POSSIBLE CAUSE!
SORTIN ,CL GAVE WRONG BLOCK SI$E FOR A VARIABLE RECORD
S314 - 04 - AN I/O ERROR OCCURRED READING A DSCB FOR A DATASET ON A
DIRECT ACCESS DEVICE DURING EXECUTION OF A CLOSE MACRO.
S314 - 08 - AN I/O ERROR OCCURRED READING A FORMAT-1 DSCB DURING
EXECUTION OF A CLOSE MACRO AND STANDARD USER LABELS WERE
SPECIFIED.
S317 - AN OCCURRED DURING A BSAM CLOSE TYPE=T MACRO FOR A DASD
FILE.
- IF THE REGISTER 15 RETURN CODE IS AVAILABLE, SUPPLY IT IN THE S%1&
OPERAND FOR MORE SPECIFIC INFORMATION! H ABEND O"S%1&-RC#
S317 - 04 - AN I/O ERROR OCCURRED READING A FORMAT-1 DSCB DURING
EXECUTION OF A BSAM CLOSE TYPE=T MACRO INSTRUCTION.
S317 - 08 - THE DSCB READ DURING EXECUTION OF A BSAM CLOSE TYPE=T
MACRO INSTRUCTION DID NOT HAVE THE EXPECTED FORMAT-1 OR
FORMAT--
FORMAT ID.
S322 - TIMED OUT, POSSIBLY NO TIME PARAMETER OR OTHER INFO
MISSING
S32D - ADDRESS IN SEGMENT TABLE OR ENTRY TABLE OUTSIDE OF
STORAGE FOR ,OB STEP AN OVERLAY PROGRAM WAS FOUND TO CONTAIN
A RECORD OF INCORRECT LENGTH, OR AN I/O ERROR WAS ENCOUNTERED -
RE-LINKEDIT IT
S337 - THE ERROR OCCURRED WHEN THE END OF A DATA SET WAS
REACHED.
- IF THE REGISTER 15 RETURN CODE IS AVAILABLE, SUPPLY IT IN THES%%&
OPERAND FOR MORE SPECIFIC INFORMATION! H ABEND O"S%%&-RC#
POSSIBLE CAUSE!
NO END OF DATA ROUTINE WAS PROVIDED
TRIED TO READ PAST END OF FILE
TRIED TO WRITE ON A TAPE DEFINED AS INPUT
S337 - 04 - THE END OF DATASET WAS REACHED, BUT NO END-OF-DATASET
ROUTINE "EODAD# WAS SPECIFIED IN THE DCB.
S337 - 08 - NO END-OF-DATASET ROUTINE "EODAD# SPECIFIED IN THE DCB
FOR DD DUMMY DATASET.
S338 - AN UNAUTHORI$ED TASK ATTEMPTED TO USE AUTHORI$ED
OPTIONS OF THE EN' MACRO INSTRUCTION.
S33E - A DETACH MACRO INSTRUCTION SPECIFYING THE STAE=YES
OPERAND HAS BEEN ISSUED BY THE ORIGINATING TASK, BUT THE
SPECIFIED SUBTASK HAS NOT COMPLETED EXECUTION.
POSSIBLE CAUSE!
THIS MAY OR MAY NOT BE AN ERROR. IF YOU INTEND FOR THE SUBTASK
TO COMPLETE PROCESSING BEFORE IT IS DETACHED, USE THE ECB OR
EXTR OPERAND ON THE ATTACH MACRO INSTRUCTION THAT CREATES THE
SUBTASK TO ACHEIVE SYNCHRONI$ATION.
S378 - THE ERROR OCCURRED DURING EXECUTION OF AN RC OR RU FORM
FREEMAIN MACRO.
- IF THE REGISTER 15 RETURN CODE IS AVAILABLE, SUPPLY IT IN THE S%&+
OPERAND FOR MORE SPECIFIC INFORMATION! H ABEND O"S%&+-RC#
POSSIBLE CAUSE!
A FREEMAIN FOR AN ENTIRE SUBPOOL WAS RE'UESTED "REGISTER 1 WAS
$ERO# BUT THE LENGTH IN REGISTER WAS NOT SET TO $ERO.
THE SPECIFIED SUBPOOL COULD NOT BE FOUND.
THE SP PARAMETER WAS SPECIFIED, BUT THE VIRTUAL STORAGE AREA TO
BE RELEASED WAS NOT WITHIN THE SUBPOOL SPECIFIED.
THE SP PARAMETER WAS NOT SPECIFIED, BUT THE VIRTUAL STORAGE
AREA TO BE RELEASED WAS NOT WITHIN SUBPOOL $ERO.
THE SP PARAMETER WAS SPECIFIED CORRECTLY, BUT THE BOUNDARIES OF
THE STORAGE AREA TO BE FREED WERE NOT COMPLETELY DESCRIBED BY
THE DESCRIPTOR 'UEUE ELEMENT "D'E#.
S378 - 08 - S'A STORAGE IS NOT IN THE SUBPOOL SPECIFIED.
S378 - 0C - CSA STORAGE IS NOT IN THE SUBPOOL SPECIFIED.
S378 - 10 - LS'A STORAGE IS NOT IN THE SUBPOOL SPECIFIED.
S378 - 14 - PRIVATE AREA STORAGE IS NOT IN THE SUBPOOL SPECIFIED.
S378 - 18 - PRIVATE AREA SUBPOOL NOT FOUND.
S378 - 1C - $ERO LENGTH WAS NOT SPECIFIED ON A SUBPOOL FREEMAIN.
S400 - THE DCB IN THE DEB DOES NOT E'UAL THE DCB ADDRESS IN THE
IOB. IN THE ABNORMAL TERMINATION DUMP, THE TCB FIELD TCBEXCPD
"AT OFFSET C# POINTS TO THE EXCP PROBLEM DETERMINATION AREA.
THE ITEMS IN THE PROBLEM DETERMINATION AREA OF GREATEST
INTEREST TO YOU ARE! "ALL OFFSETS IN HEX#
- OFFSET 1 CONTAINS A COPY OF THE REGISTERS WHEN EXCP
DETERMINED THE ERROR CONDITION.
- OFFSET 5 CONTAINS THE CONTENTS OF THE RE'UEST 'UEUE ELEMENT
"R'E# IF ALLOCATED, WHEN THE PROGRAM CHECK OCCURRED.
S402 - THE EVENTS POST MACRO INSTRUCTION ENCOUNTERED AN ERROR
WHILE PROCESSING AN EVENT CONTROL BLOCK "ECB#.
S402 - 00 - THE CONTROL PROGRAM FOUND AN INVALID EVENTS TABLE
ADDRESS IN THE % LOW-ORDER BYTES OF THE ECB SPECIFIED.
S402 - 04 - THE WAITING RB IS NOT ENABLED FOR INTERRUPTS.
S402 - 08 - FOR A WAIT OR POST IN A USER KEY, THE ECB ADDRESS IS
INVALID.
S406 - THE RE'UESTED LOAD MODULE WAS MARKED BY THE LINKAGE
EDITOR AS ONLY LOADABLE.
S40A - AN R-FORM FREEMAIN MACRO IS ATTEMPTING TO FREE AN ENTIRE
SUBPOOL THAT SHOULD NOT BE FREEMAINED.
S40A - 04 - ATTEMPTING TO FREEMAIN A SUBPOOL THAT CANNOT BE
SUBPOOL FREEMAINED.
S40A - 08 - A PROBLEM PROGRAM IS TRYING TO FREE SUBPOOL $ERO.
S40D - THIS COMPLETION CODE IS FOUND ONLY IN ASCBS. BECAUSE OF
RECURSIVE ERRORS TRYING TO TERMINATE A TASK IT BECAME
NECESSARY TO TERMINATE THE MEMORY. THE RTM ATTEMPTS TO
TERMINATE THE ADDRESS SPACE. A DUMP MAY HAVE BEEN TAKEN TO THE
SYS1.DUMP DATASET.
S413 - INPUT, INOUT, OR RDBACK SPECIFIED, BUT NO VOL SER IN DD. I/O
ERROR IN READING VOLUME LABEL. COULD NOT MOUNT VOLUME ON
DEVICE. VOLUMES SPECIFIED LESS THAN DEVICES ALLOCATED.
POSSIBLE CAUSE
FORGOTTEN VOLUME SERIAL FOR INPUT TAPE
HAD DISP NEW WHEN SHOULD HAVE HAD OLD
GENERATED AS NL, TRIED TO READ AS SL
MISSING OR INCONSISTENT DCB INFORMATION
VOLUME COULD NOT BE MOUNTED, OPERATOR MOUNTED SCRATCH
ERROR READING LABEL
OPENED A FILE AS INPUT WITHOUT FIRST GENERATING THE FILE
TRIED TO CLOSE A FILE WITHOUT OPENING IT
TRIED TO OPEN SECOND DATA SET ON A TAPE WITHOUT CLOSING THE
FIRST
THE RE'UESTED DRIVE WAS SWITCHED OFF
SORT VERB BLEW DUE TO SD NOT MATCHING FD WITH USING OR GIVING
S413-04 - UNIT NOT AVAILABLE FOR MOUNTING VOLUME
S413-08 - AN I/O ERROR OCCURRED POSITIONING A MAGNETIC TAPE
VOLUME TABE DRIVE PROBLEM"IF 1E'C1 OR 1SIM1 IN MSG# TAPE
PROBLEM"IF 1SE'1 IN MSG#
S413-0C - AN I/O ERROR OCCURRED READING THE VOLUME LABEL ON A
MAGNETIC TAPE VOLUME.
S413 - 10 - AN I/O ERROR OCCURRED WRITING A TAPE MARK.
S413-18 - UTPROC=RESTART DID NOT WORK
S413-20 - I/O ERROR READING VOLUME LABEL ON A DASD VOLUME
S413 - 24 - AN OPEN MACRO WAS ISSUED FOR A DATASET ON MAGNETIC
TAPE. A DENSITY WAS SPECIFIED IN THE DCB DEN PARAMETER WHICH WAS
INCOMPATIBLE WITH THE RECORDING DENSITY OF THE DRIVE ALLOCATED
TO THE DATASET.
S413 - 28 - NON-$ERO RETURN CODE FROM OPEN DAVV "DIRECT ACCESS
VOLUME VERIFICATION# MODULE AFTER A IEFSSRE' MACRO
INSTRUCTION. THIS CODE INDICATES THE SUBSYSTEM DISCOVERED A
FUNCTIONAL OR LOGICAL ERROR THAT IT COULD NOT PROCESS.
S413 - 2C - ERROR DURING MSS MOUNT, DEMOUNT, AC'UIRE OR
RELIN'UISH.
S413 - 30 - THE MSS HARDWARE MOUNTED THE WRONG VIRTUAL VOLUME.
S413-34 - NO REFERBACK, NO LABEL
S413 - 38 - DURING A READ BLOCK ID COMMAND TO ESTABLISH THE TAPE
POSITION, AN ERROR OCCURRED.
S413 - 40 - THE DEVICE DOES NOT SUPPORT THE RECORDING MODE
RE'UESTED BY THE USER OR DETERMINED BY THE SYSTEM.
S413 - 44 - THE TAPE VOLUME DOES NOT CONFORM TO THE SINGLE
RECORDING MODE RULES. FOR INPUT, THE VIOLATION OCCURRED WHEN
THE TAPE WAS WRITTEN WHEN THE RULES COULD NOT BE ENFORCED. FOR
OUTPUT, THE ABEND PREVENTS ANY VIOLATION FROM HAPPENING.
S414 - AN ERROR OCCURRED DURING CLOSE PROCESSING FOR A DATASET
ON A DIRECT ACCESS DEVICE.
S414 - 04 - AN I/O ERROR OCCURRED WRITING A DSCB DURING CLOSE OF A
DASD FILE.
S414 - 08 - FOR A 'SAM DATA SET EITHER AN I/O ERROR OCCURRED WHILE
FLUSHING THE BUFFERS DURING CLOSE PROCESSING, OR A CLOSE WAS
ISSUED IN THE CALLER1S SYNAD ROUTINE.
S417 - 04 - "- IS THE ONLY POSSIBLE RETURN CODE ASSOCIATED WITH
S-1&# AN I/O ERROR OCCURRED WRITING AN UPDATED FORMAT-1 DSCB
DURING THE EXECUTION OF A BSAM CLOSE TYPE=T MACRO INSTRUCTION.
S437 - AN ERROR OCCURRED DURING END-OF-VOLUME.
S437 - 08 - WHEN FEOV WAS ISSUED, THE DCB POINTER WAS INVALID.
S437 - 0C - DEB NOT IN DEB TABLE.
S478 - AN RC-FORM OR RU-FORM FREEMAIN MACRO IS ATTEMPTING TO
FREE AN ENTIRE SUBPOOL THAT SHOULD NOT BE FREEMAINED.
S478 - 04 - ATTEMPTING TO FREEMAIN A SUBPOOL THAT CANNOT BE
SUBPOOL FREEMAINED.
S478 - 08 - A PROBLEM PROGRAM IS TRYING TO FREE SUBPOOL $ERO.
S502 - DURING EXECUTION OF A POST MACRO INSTRUCTION, THE
CONTROL PROGRAM FOUND THAT THE EVENTS TABLE SPECIFIED IN THE
ECB HAD NO AVAILABLE ENTRIES TO CONTAIN THE POSTED ECB ADDRESS.
S504 - 04 - "- IS THE ONLY POSSIBLE RETURN CODE ASSOCIATED WITH
S5-# AT LEAST ONE OVERLAP AMONGST LENGTH LIST, ADDRESS LIST AND
PARAMETER LIST AT GETMAIN EXECUTION TIME.
S505 - 04 - "- IS THE ONLY POSSIBLE RETURN CODE ASSOCIATED WITH
S55# AT LEAST ONE OVERLAP AMONGST LENGTH LIST, ADDRESS LIST AND
PARAMETER LIST AT FREEMAIN EXECUTION TIME.
S513 - THE ERROR OCCURRED DURING EXECUTION OF AN OPEN MACRO
INSTRUCTION FOR A DATA SET ON MAGNETIC TAPE.
S513 - 04 - AN OPEN MACRO WAS ISSUED FOR A MAGNETIC TAPE DATASET
ALLOCATED TO A DEVICE THAT ALREADY HAS AN OPEN DATASET ON IT.
S513 - 08 - A LABEL VIOLATED THE PUBLISHED STANDARD FOR THAT
LABEL, AND THE LABEL VALIDATION EXIT RE'UESTED OPEN/EOV TO
RE,ECT THE VOLUME.
S513 - 0C - NON-STANDARD VOL1 HEADER ON AN ASCII TAPE.
S522 - TIMED OUT - TAPE NOT MOUNTED, HSM RECALL
S546 - CANCELLED BY OPERATOR OR SYSTEM
S567 - HARDWARE ERROR - BLOCK OF DATA MISSED OR SKIPPED
S582 - 00 - " IS THE ONLY POSSIBLE RETURN CODE ASSOCIATED WITH
S5+)# WHILE PERFORMING RACHECK SVC PROCESSING, RACF WAS UNABLE
TO VERIFY A USER BECAUSE NO ACCESS CONTROL ENVIRONMENT "ACEE#
WAS AVAILABLE.
77POSSIBLE CAUSE8 77
USER LOGGED ON OR ,OB STARTED WHILE RACF WAS INACTIVE, BUT RACF
HAS SINCE BEEN REACTIVATED.
S604 - GETMAIN ERROR
POSSIBLE CAUSE
MISSING SORTLIB CARD
SUBSCRIPT ERROR - CLOBBERED FREE 'UEUE ELEMENT
S604 - 04 - THE PARAMETER LIST IS NOT ON A WORD BOUNDARY.
S604 - 08 - THE PARAMETER LIST IS IN PROTECTED STORAGE.
S604 - 0C - THE LENGTH LIST IS NOT ON A WORD BOUNDARY.
S604 - 10 - THE LENGTH LIST IS IN PROTECTED STORAGE.
S604 - 14 - THE ADDRESS LIST IS NOT ON A WORD BOUNDARY.
S604 - 18 - THE ADDRESS LIST IS IN PROTECTED STORAGE.
S604 - 1C - THE PARAMETER LIST RE'UEST FLAGS ARE INVALID.
S605 - FREEMAIN ERROR
POSSIBLE CAUSE
MISSING SORTLIB CARD
SUBSCRIPT ERROR - CLOBBERED FREE 'UEUE ELEMENT
S605 - 04 - THE PARAMETER LIST IS NOT ON A WORD BOUNDARY.
S605 - 08 - THE PARAMETER LIST IS IN PROTECTED STORAGE.
S605 - 0C - THE LENGTH LIST IS NOT ON A WORD BOUNDARY.
S605 - 10 - THE LENGTH LIST IS IN PROTECTED STORAGE.
S605 - 14 - THE ADDRESS LIST IS NOT ON A WORD BOUNDARY.
S605 - 18 - THE ADDRESS LIST IS IN PROTECTED STORAGE.
S605 - 1C - THE PARAMETER LIST RE'UEST FLAGS ARE INVALID.
S60A - "NON-MVS/XA# FREEMAIN 'UEUE ELEMENT OR ADDRESS ERROR
NEEDS MORE CORE ,CL FOR INPUT DISKS RE'UESTED ) UNITS, GAVE 1
VOLUME SERIAL FORGOT DD CARD FOR SYS1.SORTLIB
S613 - I/O ERROR IN TAPE POSITIONING OR LABEL PROCESSING
POSSIBLE CAUSE
TAPE LABEL WAS NOT IN RE'UESTED DENSITY
DCB MISSING
DEN MISSING ON A TAPE THAT RE'UIRES IT DEFAULT DEN=% "1* BPI#
RECFM=F WAS SPECIFIED FOR A FILE WHICH WAS FB
INCORRECT HEADER
TAPE POSITIONING ERROR
TAPE DRIVE FAILURE DURING OPEN
S613 - 04 - AN I/O ERROR OCCURRED POSITIONING A MAGNETIC TAPE
VOLUME.
S613-08 - TAPE POSITIONING ERROR
S613(SF13) - BAD TAPE OR DRIVE - ERROR READING LABEL ON TAPE IF YOU
SEE MESSAGE IN RMDS OUTPUT! DATA SET NAME DOES NOT MATCH FOR A
MASTER VOLUME INSTALLATION OPTION ALLOWS UPDATE OF ONLY THE
LAST FILE ON MASTER VOLUMES CHECK ,CL AT FAILED STEP TO MAKE
SURE LABEL IS CORRECT - POSSIBLY NO LABEL
S613 - 0C - AN INVALID LABEL WAS READ FROM A MAGNETIC TAPE
VOLUME. THIS ERROR MAY BE DUE TO A PREVIOUS ABNORMAL
TERMINATION ASSOCIATED WITH THE SAME TAPE SINCE IT WAS LAST
MOUNTED, POSSIBLY IN A PREVIOUS ,OB OR STEP, LEAVING THE TAPE
POSITIONED IMPROPERLY.
S613 - 10 - AN I/O ERROR OCCURRED WRITING A TAPE LABEL.
S613 - 14 - AN I/O ERROR OCCURRED WRITING A TAPE MARK AFTER THE
HEADER LABELS.
S614 - AN ERROR OCCURRED DURING CLOSE PROCESSING FOR A DATASET
ON A DIRECT ACCESS DEVICE OR FOR A SUBSYSTEM DATASET.
POSSIBLE CAUSE
OPERATOR DISMOUNTED VOLUME WHILE PROGRAM WAS PROCESSING
S614 - 04 - AN I/O ERROR OCCURRED WRITING A FILE MARK FOR A DATASET
ON A DIRECT ACCESS DEVICE DURING EXECUTION OF A CLOSE MACRO.
POSSIBLE CAUSE
OPERATOR DISMOUNTED VOLUME WHILE PROGRAM WAS PROCESSING
S614 - 08 - A FILE MARK SHOULD HAVE BEEN WRITTEN ON AN OUTPUT
DATASET. THE DCBFDAD FIELD IN THE DCB INDICATED AN EXTENT
NUMBER IN THE DEB GREATER THAN THE NUMBER OF EXTENTS IN THE
DATASET. CONSE'UENTLY, IT COULD NOT BE DETERMINED WHERE THE
FILE MARK
SHOULD HAVE BEEN WRITTEN.
S614 - 0C - IEFSSRE' MACRO RETURNED AN ERROR CODE IN REGISTER 15
WHICH INDICATES THAT THE SUBSYSTEM WAS NOT OPERATING.
S614 - 10 - A SPOOLED OR SUBSYSTEM DATASET COULD NOT BE CLOSED BY
THE ,OB ENTRY SUBSYSTEM OR ALTERNATE SUBSYSTEM.
S614 - 14 - A CLOSE MACRO INSTRUCTION DETECTED AN ERROR RETURN
CODE FROM AN SMS SERVICE WHILE PROCESSING A PDSE DATA SET.
S622 - TSO SESSION WAS CANCELLED OPERATOR STOPPED TSO OR
CANCELLED THE USER USER SIGNALLED ATTN AFTER THE ALLOCATION
PROCESS HAD COMPLETED THE USER DISCONNECTED HIS TERMINAL
FROM THE SYSTEM
S637 - I/O ERROR IN WRITING TAPE MARK, TAPE POSITIONING, READING
LABEL, SENSING FOR FILE PROTECTION RING. DCB BIT DOES NOT
INDICATE CONCATENATION OF UNLIKE ATTRIBUTES. IMPROPER INFO ON
,CL FOR MULTIREEL NSL TAPE
S637-OC - CONCATENATION ON UNLIKE ATTRIBUTES
S637-2C - I/O ERROR READING HEADER LABEL ON TAPE
S637 - 04 - AN I/O ERROR OCCURRED WHILE READING A TAPE LABEL,
WRITING A TAPE MARK, OR POSITIONING A MAGNETIC TAPE VOLUME.
S637 - 08 - FOLLOWING USER TRAILER LABEL PROCESSING, AN I/O ERROR
OCCURRED POSITIONING A MAGNETIC TAPE.
S637 - 0C - CONCATENATION OF DATASETS WITH UNLIKE ATTRIBUTES WAS
DETECTED, BUT NOT SPECIFIED IN THE DCB.
S637 - 10 - AN I/O ERROR OCCURRED WHILE POSITIONING A MAGNETIC
TAPE DATASET THAT WAS OPENED WITH THE OPTION INPUT OR INOUT TO
BE READ BACKWARD. IF IT IS A TAPE WITH STANDARD LABELS, THE ERROR
OCCURRED POSITIONING AT THE LABELS. IF IT IS A TAPE WITH NO LABELS,
THE ERROR OCCURRED POSITIONING AT THE DATA.
S637 - 14 - AN I/O ERROR IN TAPE POSITIONING OCCURRED FOR A DATASET
WITH THE LEAVE OPTION SPECIFIED IN THE OPEN MACRO OR IN THE FEOV
MACRO.
S637 - 18 - AN I/O ERROR IN TAPE POSITIONING OCCURRED FOR A DATASET
OPENED WITH THE REREAD OPTION.
S637 - 1C - AN I/O ERROR IN TAPE POSITIONING OCCURRED WHEN FEOV
WAS ISSUED FOR A DATASET WITH DISP=PASS AND NO OPEN OPTION )
SPECIFIED.
S637 - 20 - RDBACK WAS INVALIDLY SPEICFIED FOR A NEW CONCATENATED
TAPE VOLUME. RDBACK IS NOT SUPPORTED WITH CONCATENATION.
S637 - 24 - AN I/O ERROR OCCURRED REWINDING A SCRATCH MAGNETIC
TAPE VOLUME. EITHER FEOV WITH A REWIND OPTION WAS ISSUED, OR NO
OPEN OPTION ) WAS SPECIFIED WHEN THE DISPOSITION WAS NOT PASS.
S637 - 2C - AN I/O ERROR OCCURRED WHILE REWINDING A MAGNETIC TAPE
VOLUME PRIOR TO VERIFYING THE VOLUME LABEL.
S637-34 - I/O ERROR READING END OF VOLUME LABEL
S& - A PROGRAM CHECK OCCURRED DURING EXCP PROCESSING OF AN
I/O RE'UEST. THE PROGRAM CHECK OCCURRED IN A SUPERVISOR SERVICE
ROUTINE CALLED BY EXCP. THIS IS LIKELY NOT A PROGRAMMER ERROR.
IN THE ABNORMAL TERMINATION DUMP, THE TCB FIELD TCBEXCPD "AT
OFFSET C# POINTS TO THE EXCP PROBLEM DETERMINATION AREA. THE
ITEMS IN THE PROBLEM DETERMINATION AREA OF GREATEST INTEREST TO
YOU ARE! "ALL OFFSETS IN HEX#
- OFFSET ) CONTAINS A FLAG BYTE INDICATING WHERE THE ERROR
OCCURRED.
THE BIT PATTERN IS AS FOLLOWS!
19 9. ERROR IN SVC PORTION OF EXCP
.1.. 9. ERROR IN SRB PORTION OF EXCP
..1. 9. ERROR IN PCI APPENDAGE
91 9. ERROR IN CHE APPENDAGE
9. 19 ERROR IN ABE APPENDAGE
9. .1.. ERROR IN EOE APPENDAGE
9. ..1. ERROR IN PGFX APPENDAGE
9. 91 APENDAGE IS ACTIVE
9. 9. ERROR IN SIO APPENDAGE
- OFFSET - CONTAINS A COPY OF THE PROGRAM STATUS WORD "PSW#
BEFORE RTM WAS ENTERED.
- OFFSET E CONTAINS THE INTERRUPTION CODE. THE ABEND MACRO.
- OFFSET 5- CONTAINS THE CONTENTS OF THE RE'UEST 'UEUE ELEMENT
"R'E#, IF ALLOCATED, FOR THE I/O RE'UEST BEING PROCESSED
S706 - A LOAD MODULE MARKED FOR THE LINKAGE EDITOR IS NON-
EXECUTABLE
S713 - TRIED TO WRITE ON A DATASET WHOSE DATE PROTECTION HAD NOT
EXPIRED. OPERATOR REPLIED 1M1 TO IEC5&D TO HONOR EXP DATE.
S713 - 04 - A DATASET ON MAGNETIC TAPE WAS OPENED FOR INOUT, OUTIN,
OUTPUT, OUTINX, OR EXTEND, BUT THE VOLUME CONTAINED A DATASET
WHOSE EXPIRATION DATE HAD NOT BEEN REACHED.
S713 - 08 - AN OPEN MACRO WAS ISSUED WITH INOUT FOR A DATASET ON A
DIRECT ACCESS DEVICE WITH DISP=OLD SPECIFIED ON THE DD
STATEMENT. THE EXPIRATION DATE ON THE DATASET HAD NOT BEEN
REACHED.
S713 - 0C - THE OPERATOR REPLIED 1M1 TO IEC&-A TO RE,ECT THE RE'UEST
TO REWRITE THE TAPE VOLUME1S VOL1 HEADER.
S714 - I/O ERROR IN LABEL PROCESSING - CLOSE FOR MAGNETIC TAPE TAPE
DRIVE FAILURE DURING CLOSE
S714 - 04 - AN I/O ERROR OCCURRED WRITING TRAILER LABEL 1 FOR A
DATASET ON MAGNETIC TAPE DURING EXECUTION OF A CLOSE MACRO.
S714 - 08 - AN I/O ERROR OCCURRED WRITING TRAILER LABEL ) FOR A
DATASET ON MAGNETIC TAPE DURING EXECUTION OF A CLOSE MACRO.
S714-0C - AN I/O ERROR OCCURRED WRITING A TAPE MARK DURING
EXECUTION OF A CLOSE MACRO.
S717 - AN I/O ERROR OCCURRED DURING EXECUTION OF A BSAM CLOSE
TYPE=T MACRO INSTRUCTION. THE RETURN CODE INDICATES THE EXACT
ERROR.
S717 - 04 - I/O ERROR FOR BSAM CLOSE TYPE=T WHEN WRITING A TAPE
MARK FOLLOWING THE LAST RECORD
S717 - 08 - I/O ERROR FOR BSAM CLOSE TYPE=T WHEN WRITING TRAILER
LABEL-1 OR TRAILER LABEL-)
S717 - 0C - I/O ERROR FOR BSAM CLOSE TYPE=T WHEN WRITING A TAPE
MARK FOLLOWING THE TRAILER LABELS
S717 - 10 - I/O ERROR FOR BSAM CLOSE TYPE=T WHEN READING TRAILER
LABEL-1 TO UPDATE THE DCB BLOCK COUNT
S718 - NOT ENOUGH REGION TO LOAD MODULES
S722 - LINES EXCEEDED, ADD A MAIN LINES CARD - //(MAIN
LINES="1,WARNING#
S737 - I/O ERROR. DSCB NOT FOUND FOR MULTI-VOLUME OR
CONCATENATEDDATA SET. BE SURE ALL THE DATA SETS EXIST FOR
CONCATENATED DATA SETS
- IF THE REGISTER 15 RETURN CODE IS AVAILABLE, SUPPLY IT IN THE
OPERAND FOR MORE SPECIFIC INFORMATION! H ABEND O"S&%&-RC#
S737 - 04 - AN I/O ERROR OCCURRED READING A DSCB DURING END OF
VOLUME PROCESSING OR THE DSCB COULD NOT BE FOUND ON THE
SPECIFIED VOLUME.
S737 - 08 - AN I/O ERROR OCCURRED READING A DIRECT ACCESS VOLUME
LABEL DURING END OF VOLUME PROCESSING.
S737 - 0C - AN I/O ERROR OCCURRED READING THE DSCB FOR A
CONCATENATED PARTITIONED DATASET.
S737 - 10 - AN I/O ERROR OCCURRED WRITING A FILE MARK FOR A DATASET
ON A DIRECT ACCESS DEVICE.
S737 - 14 - AN I/O ERROR OCCURRED READING A DSCB PREPARING FOR
USER TRAILER LABEL PROCESSING.
S737 - 1C - AN I/O ERROR OCCURRED WHILE READING A FORMAT-% DSCB.
S737-24 - DSN NOT FOUND. A MISSING MEMBER NAME WAS DETECTED BY
BLDL WHILE SEARCHING FOR THE TTR OF A CONCATENATED MEMBER.
S737 - 2C - THE ERROR OCCURRED WHEN A FEOV MACRO WAS ISSUED
WHILE ATTEMPTING TO WRITE A FILE MARK AT THE END OF DATA. THE
DCBFDAD FIELD IN THE DCB INDICATED AN EXTENT NUMBER IN THE DEB
GREATER THAN THE NUMBER OF EXTENTS IN THE DATASET.
CONSE'UENTLY IT COULD NOT BE DETERMINED WHERE THE FILE MARK
SHOULD HAVE BEEN WRITTEN.
S737 - 3C - THE FORMAT-1 DSCB NOT FOUND INSTALLATION EXIT MODULE
ENCOUNTERED AN ERROR.
S738 - AN UNEXPECTED ERROR OCCURRED DURING THE EXECUTION OF AN
EN' MACRO. RELATED INFORMATION IS RECORDED IN SYS1.LOGREC.
S777 - DATA CHECK. TRANSMIT ON INPUT
S800 - AN ERROR OCCURRED WHEN EXCP ATTEMPTED TO FIX A PAGE FOR
THIS EXCP RE'UEST.
S804 - RE'UEST FOR BYTES OF VIRTUAL STORAGE OR NOT ENOUGH
VIRTUAL STORAGE AVAILABLE FOR GETMAIN RE'UEST.
- IF THE REGISTER 15 RETURN CODE IS AVAILABLE, SUPPLY IT IN THE S+-
OPERAND FOR MORE SPECIFIC INFORMATION! H ABEND O"S+--RC#
POSSIBLE CAUSE!
PROGRAM EXCEEDED REGION SI$E
S804 - 04 - THERE IS NOT ENOUGH VIRTUAL S'A TO SATISFY THE RE'UEST.
S804 - 08 - THERE IS NOT ENOUGH VIRTUAL CSA TO SATISFY THE RE'UEST.
S804 - 0C - THERE IS NOT ENOUGH VIRTUAL LS'A TO SATISFY THE
RE'UEST.
S804 - 10 - THERE IS NOT ENOUGH PRIVATE AREA TO SATISFY THE RE'UEST.
MAY BE A V=R REGION BEFORE ITS INITIALI$ATION HAS COMPLETED.
S804 - 1C - THERE IS NOT ENOUGH VIRTUAL LS'A FOR VSM1S CELLPOOL
RE'UIRED DURING THE RE'UEST.
S805 - 1C - "1C IS THE ONLY POSSIBLE RETURN CODE ASSOCIATED WITH
S+5# THERE IS NOT ENOUGH VIRTUAL LS'A FOR VSM1S CELLPOOL
RE'UIRED DURING THE FREEMAIN RE'UEST.
S806 - BLDL DETECTED ERROR! MODULE NOT FOUND OR I/O ERROR
DURING DIRECTORY SEARCH
POSSIBLE CAUSE
MISSING ,OBLIB OR STEPLIB CARD
TRIED TO EXECUTE A NON-EXISTENT PROGRAM
TRIED TO EXECUTE IN BATCH A PROGRAM ASSEMBLED WITH 1TEST1
OPTION
SYSIN DESCRIBED INCORRECTLY TO LKED OR NAME CARD MISSING
S806 - 04 - THE PROGRAM ENTRY POINT SPECIFIED WAS NOT FOUND IN THE
INDICATED LIBRARY "PRIVATE LIBRARY, ,OB LIBRARY, OR LINK LIBRARY#.
S806 - 08 - AN UNCORRECTABLE INPUT/OUTPUT ERROR OCCURRED WHEN
THE BLDL CONTROL PROGRAM ROUTINE ATTEMPTED TO SEARCH THE
DIRECTORY OF THE LIBRARY THAT CONTAINED THE PROGRAM WHOSE
ENTRY POINT WAS SPECIFIED. THIS CAN OCCUR IF THE INDICATED
LIBRARY IS AN UNINITIALI$ED PARTITIONED DATASET.
S806 - 0C - THE SUPERVISOR ATTEMPTED TO SEARCH A LIBRARY FOR THE
SPECIFIED ENTRY POINT, BUT THE DCB OF THE LIBRARY WAS NOT OPEN.
S806 - 10 - AN EXPLICIT LOAD WAS ISSUED WITH NO DCB SPECIFIED.
S806 - 14 - AN SVC ROUTINE RE'UIRED BY THE SYSTEM COULD NOT BE
FOUND IN THE LINK PACK AREA.
S806 - 18 - AN SVC ROUTINE RE'UIRED BY THE SYSTEM COULD NOT BE
FOUND IN THE LINK PACK AREA BECAUSE THE DIRECTORY WAS NOT YET
BUILT.
S806 - 1C - SPECIFIED DCB FOR ATTACH, LINK, LOAD, OR XCTL IS
INCORRECT.
S80A - RE'UEST FOR BYTES OF VIRTUAL STORAGE OR NOT ENOUGH
VIRTUAL STORAGE AVAILABLE FOR GETMAIN OR FREEMAIN RE'UEST.
S80A - 04 - THERE IS NOT ENOUGH VIRTUAL S'A TO SATISFY THE RE'UEST.
S80A - 08 - THERE IS NOT ENOUGH VIRTUAL CSA TO SATISFY THE RE'UEST.
S80A - 0C - THERE IS NOT ENOUGH VIRTUAL LS'A TO SATISFY THE
RE'UEST.
S80A - 10 - THERE IS NOT ENOUGH PRIVATE AREA TO SATISFY THE RE'UEST.
MAY BE A V=R REGION BEFORE ITS INITIALI$ATION HAS COMPLETED.
S80A - 1C - THERE IS NOT ENOUGH VIRTUAL LS'A FOR VSM1S CELLPOOL
RE'UIRED DURING THE RE'UEST.
S813 - 04 - "- IS THE ONLY POSSIBLE RETURN CODE ASSOCIATED WITH
S+1%#AN OPEN MACRO WAS ISSUED FOR A DATASET ON MAGNETIC TAPE,
BUT THE DATASET NAME ON THE HEADER LABEL DID NOT MATCH THAT IN
THE ,FCB.
POSSIBLE CAUSE
WRONG DSNAME OR VOLUME SERIAL - ,CL DISAGREES WITH LABEL
INCORRECT RECORD FORMAT OR BLOCK SI$E
THE RE'UESTED DRIVE WAS NOT SWITCHED TO THIS MACHINE
S822 - A REGION RE'UIRED TO RUN THE STEP COULD NOT BE OBTAINED.
ONE OF THE FOLLOWING MESSAGES WILL BE WRITTEN TO THE
PROGRAMMER, DEPENDING UPON WHETHER THE ,OB WAS AN ORDINARY
,OB OR A DEFERRED CHECKPOINT RESTART!
- IEF+5I REGION UNAVAILABLE, ERROR CODE = CDE
- IEF1+*I REGION UNAVAILABLE FOR RESTART, ERROR CODE = CDE
S822 - 08 - IEF+5I - A V=V REGION WAS RE'UESTED AND A REGION SI$E
WAS SPECIFIED WHICH WAS LARGER THAN THE PRIVATE AREA, OR A V=R
REGION WAS RE'UESTED AND A REGION SI$E GREATER THAN THE V=R
AREA WAS SPECIFIED.
IEF1+*I - THE REGION PARAMETER WAS INCREASED SO THAT THE REGION
COULD NOT BE ALLOCATED OR THE CONFIGURATION OF THE SYSTEM
CHANGED SO THAT THE REGION COULD NOT BE OBTAINED!
- FOR ADDRSPC=REAL, THE SI$E OF THE REAL AREA WAS DECREASED.
- FOR ADDRSPC=VIRT, THE SI$E OF THE PRIVATE AREA DECREASED
BECAUSE THE SI$E OF THE NUCLEUS INCREASED OR THE SI$E OF THE S'A
OR THE IPA INCREASED.
S822 - 16 - IEF+5I - A V=R AREA WAS RE'UESTED, BUT EITHER LONG-FIXED
OR DAMAGED PAGES IN THE V=R AREA MADE IT IMPOSSIBLE TO OBTAIN
THE RE'UESTED REGION, OR A V=R REGION WAS RE'UESTED AND THERE
WAS NOT ENOUGH S'A AVAILABLE FOR THE SYSTEM TO COMPLETE THE
PROCESSING OF THE RE'UEST.
IEF1+*I - IF A REAL REGION WAS RE'UESTED, EITHER LONG-FIXED OR
DAMAGED PAGES IN THE REAL AREA MADE IT IMPOSSIBLE TO OBTAIN THE
RE'UIRED REGION.
S822 - 20 - IEF+5I AND IEF1+*I - EITHER A V=V OR V=R REGION WAS
RE'UESTED FRAGMENTATION BY LS'A, SWA, OR SUBPOOLS ))/ OR )%
HAS MADE IT IMPOSSIBLE TO OBTAIN THE RE'UESTED REGION.
S822 - 24 - IEF+5I AND IEF1+*I - A RE'UEST FOR A V=R REGION COULD NOT
BE SATISFIED BECAUSE THE INSTALLATION GETPART EXIT ROUTINE
RE,ECTED THE RE'UEST.
S837 - THE ERROR OCCURRED DURING END OF VOLUME FOR A
SE'UENTIAL DATA SET.
S837 - 04 - THE UNIT IS NOT CAPABLE OF HANDLING THE RE'UESTED
DENSITY.
S837 - 08 - THE VOLUME SERIAL NUMBER WAS NOT FOUND IN THE ,FCB.
POSSIBLE CAUSES
VOLUME COUNT TO SMALL IN VOL PARAMETER OF DD STATEMENT
OPEN TYPE=, WAS USED TO CHANGE VOLUME SERIAL BUT NOT WRITTEN
BACK
S837 - 0C - ANOTHER DATA SET ON THE VOLUME WAS IN USE.
S837 - 10 - THE DEVICE DOES NOT SUPPORT THE SELECTED RECORDING
MODE.
S837 - 14 - THE TAPE VOLUME DOES NOT CONFORM TO THE SINGLE
RECORDING MODE RULES. FOR INPUT, THE VIOLATION OCCURRED WHEN
THE TAPE WAS WRITTEN WHEN THE RULES COULD NOT BE ENFORCED. FOR
OUTPUT,
THE ABEND PREVENTS ANY VIOLATION FROM HAPPENING.
S848 - NOT ENOUGH REGION. INCREASE THE REGION SI$E, 1REGION=-/*K1
S878 - RE'UEST FOR BYTES OF VIRTUAL STORAGE OR NOT ENOUGH
VIRTUAL STORAGE AVAILABLE FOR GETMAIN OR FREEMAIN RE'UEST.
S878 - 04 - THERE IS NOT ENOUGH VIRTUAL S'A TO SATISFY THE RE'UEST.
S878 - 08 - THERE IS NOT ENOUGH VIRTUAL CSA TO SATISFY THE RE'UEST.
S878 - 0C - THERE IS NOT ENOUGH VIRTUAL LS'A TO SATISFY THE
RE'UEST.
S878 - 10 - THERE IS NOT ENOUGH PRIVATE AREA TO SATISFY THE RE'UEST.
MAY BE A V=R REGION BEFORE ITS INITIALI$ATION HAS COMPLETED.
S878 - 14 - A NEGATIVE STORAGE AMOUNT WAS SPECIFIED FOR A GETMAIN.
S878 - 18 - A NEGATIVE STORAGE AMOUNT WAS SPECIFIED FOR A
FREEMAIN.
S878 - 1C - THERE IS NOT ENOUGH VIRTUAL LS'A FOR VSM1S CELLPOOL
RE'UIRED DURING THE RE'UEST.
S905 - 04 - "- IS THE ONLY POSSIBLE RETURN CODE ASSOCIATED WITH
S/5# AREA TO BE FREED BY FREEMAIN IS NOT ON A DOUBLEWORD
BOUNDARY.
S90A - 04 - "- IS THE ONLY POSSIBLE RETURN CODE ASSOCIATED WITH
S/A# THE ERROR OCCURRED DURING THE EXECUTION OF AN R-FORM
FREEMAIN MACRO. THE ADDRESS OF THE STORAGE AREA TO BE
RELEASED WAS NOT ON A DOUBLEWORD BOUNDARY "A MULTIPLE OF +#.
S913 - THE ERROR OCCURRED DURING!
1# THE EXECUTION OF AN OPEN MACRO OR DURING END-OF-VOLUME
PROCESSING FOR A PASSWORD PROTECTED DATASET, OR )# THE
EXECUTION OF AN OPEN MACRO INVOLVING A CHECKPOINT DATASET
POSSIBLE CAUSE
OPERATOR FAILED TO SUPPLY CORRECT PASSWORD FOR PROTECTED
DATASET
UNAUTHORI$ED ATTEMPT TO USE LABEL=BLP
PREVIOUS DATASET ON THIS TAPE WAS PROTECTED, NEW DATASET IS NOT
S913 - 04 - AN OPEN MACRO WAS ISSUED FOR A MAGNETIC TAPE DATASET
WITH AMERICAN NATIONAL STANDARD LABELS. THE VOLUME
ACCESSABILITY BYTE "OFFSET X1A1# IN THE VOLUME LABEL IS NOT
BLANK. THIS INDICATES THE LABEL WAS NOT WRITTEN FOR USE ON AN
IBM SYSTEM, OR THAT IT WAS WRITTEN BY THE USER. THE VOLUME MUST
BE RECREATED.
S913 - 08 - AN OPEN MACRO WAS ISSUED FOR A MAGNETIC TAPE DATASET
WITH AMERICAN NATIONAL STANDARD LABELS. THE SECURITY BYTE IN
THE HEADER LABEL WAS NOT BLANK AND NOT E'UAL TO X1F11. THIS
MEANS THE LABEL EITHER WAS NOT CREATED ON AN IBM SYSTEM OR WAS
CREATED BY THE USER. THE VOLUME MUST BE RECREATED FOR USE ON
AN IBM SYSTEM.
S913 - 0C - AN OPEN MACRO WAS ISSUED FOR A PROTECTED DATASET FOR
WHICH YOU ARE NOT ALLOWED THIS TYPE OF ACCESS.
S913 - 10 - AN OPEN MACRO WAS ISSUED TO THE VTOC FOR OUTPUT
PROCESSING BY AN UNAUTHORI$ED ,OB STEP OR ,OB-STEP TASK.
S913 - 14 - AN OPEN MACRO WAS ISSUED TO CONCATENATE CHECKPOINT
AND NONCHECKPOINT DATASETS.
S913 - 18 - AN OPEN TYPE=, MACRO WAS ISSUED FOR A MAGNETIC TAPE
VOLUME. THE ,FCB WAS MODIFIED TO INDICATE LABEL=BLP "BYPASS
LABEL PROCESSING# AN THE TASK WAS NOT AUTHORI$ED. BLP MAY BE
SPECIFIED IN THE ,CL "IF THE INSTALLATION READER PROCEDURE
ALLOWS IT#, BUT THE ,FCB MAY NOT BE MODIFIED TO INDICATE BLP
UNLESS THE TASK IS
AUTHORI$ED.
S913 - 1C - THE ERROR OCCURRED DURING THE EXECUTION OF AN OPEN
TYPE=, MACRO TO A DIRECT ACCESS DEVICE DATASET. THE DATASET
NAME SUPPLIED TO OPEN WAS NOT AVAILABLE TO THE ,OB. EITHER THE
DATASET WAS BEING
OPENED FOR INPUT AND SOME OTHER ,OB HAD EXCLUSIVE CONTROL OF
IT, OR THE DATASET WAS BEING OPENED FOR AN OPTION OTHER THAN
INPUT "THUS RE'UIRING EXCLUSIVE CONTROL# AND SOME OTHER ,OB
WAS USING THE DATASET.
S913 - 20 - AN OPEN MACRO USING THE EXCP ACCESS METHOD WAS ISSUED
IN WHICH USER-WRITTEN APPENDAGES WERE RE'UIRED. THE APPENDAGE
NAMES WERE NOT INCLUDED IN THE PARMLIB MEMBER IEAAPP, AND
THE PROGRAM
ISSUING THE OPEN WAS NOT AUTHORI$ED "BY APF OR PROTECT KEY#.
S913 - 28 - AN OPEN MACRO WAS ISSUED FOR A CHECKPOINT DATASET. THE
DATASET ORGANI$ATION WAS NOT BPAM OR BSAM AND THE TASK WAS
NOT AUTHORI$ED VIA THE AUTHORI$ED PROGRAM FACILITY "APF#.
S913 - 2C - AN OPEN MACRO WAS ISSUED TO AN ISAM DATASET DEFINED BY
TWO OR THREE DD STATEMENTS. EITHER THE DATASET NAMES CODED IN
THE DD STATEMENTS WERE NOT ALL THE SAME, OR THE ,FCB PASSED TO
OPEN
"IF AN OPEN TYPE=, IS BEING USED# HAS A DATASET NAME DIFFERENT
FROM THAT CODED IN THE DD STATEMENTS.
S913 - 30 - AN OPEN MACRO WAS ISSUED TO WRITE A DATASET ON A
MAGNETIC TAPE CONTAINING ONE OR MORE PREVIOUS DATASETS. THE
PROTECTION MODE OF THE DATASET TO BE WRITTEN WAS DIFFERENT
THAN THE PROTECTION MODE OF THE PREVIOUS DATASET.
S913 - 34 - AT OPEN, THE CALLER IS NOT AUTHORI$ED TO RE,ECT FOR
INPUT.
S913 - 38 - AN OPEN WAS ISSUED FOR A RACF-PROTECTED DATA SET ON
DASD OR A RACF-PROTECTED TAPE VOLUME TO WHICH THE CALLER WAS
NOT AUTHORI$ED.
S913 - 3C - AN OPEN WAS ISSUED FOR A RACF-INDICATED "RACF BIT ON IN
THE FORMAT-1 DSCB IN THE VTOC# DATA SET, BUT THE DATA SET IS NOT
DEFINED TO RACF.
S913 - 40 - A VSAM DATA SPACE BEING OPENED IS RACF-DEFINED.
S913 - 44 - INVALID SPECIFICATION OF PROTECT - THE TAPE VOLUME WAS
ALREADY RACF-PROTECTED.
S913 - 48 - INVALID SPECIFICATION OF PROTECT - THE SYSTEM TAPE
OPTION IS NOT IN EFFECT.
S913 - 4C - INVALID SPECIFICATION OF PROTECT - THE USER IS NOT
DEFINED TO RACF.
S913 - 50 - INVALID SPECIFICATION OF PROTECT - THE RE'UEST IS FOR A
NL, BLP OR LTM TAPE.
S913 - 54 - INVALID SPECIFICATION OF PROTECT - THE RE'UEST IS FOR
INPUT OR INOUT.
S913 - 58 - INVALID SPECIFICATION OF PROTECT - THE VOLUME SE'UENCE
NUMBER OR THE FILE SE'UENCE NUMBER IS NOT E'UAL TO ONE ON A AL,
SUL, AL OR AUL TAPE, OR THE TAPE IS BEING OPENED WITH DISP=MOD
"INCLUDING OPEN OPTIONS OUTINX AND EXTEND#.
S913 - 5C - INVALID SPECIFICATION OF PROTECT - THE VOLUME BEING
USED IS A PUBLIC VOLUME.
S913 - 60 - THE USER IS NOT AUTHORI$ED TO DEFINE A DATA SET WITH THE
SPECIFIED NAME. THIS NAME AND FILE SE'UENCE INDICATOR DO NOT
MATCH THE CORRESPONDING NAMES IN THE TVTOC "TAPE VTOC#.
S913 - 64 - THE USER IS NOT AUTHORI$ED TO SPECIFY BLP.
S913 - 68 - THE USER IS NOT AUTHORI$ED TO ADD A DATA SET TO THE
VOLUME.
S913 - 6C - PROTECT WAS NOT SPECIFIED IN THE ,CL. THE USER IS NOT
AUTHORI$ED TO DEFINE A DATASET PROTECTED BY A GENERIC PROFILE.
S913 - 70 - THE USER HAS RACF EXECUTE ACCESS ONLY AND ONE OF THE
FOLLOWING RE'UIREMENTS WAS VIOLATED!
- THE CALLER MUST BE IN SUPERVISOR STATE OR THE DATA SET MUST BE A
PDS.
- THE ACCESS METHOD MUST NOT BE EXCP.
S913 - 72 - AN UNEXPECTED RETURN CODE HAS BEEN RETURNED FROM
RACF.
S922 - SPECIFIED MU TIME EXCEEDED
S978 - 04 - "- IS THE ONLY POSSIBLE RETURN CODE ASSOCIATED WITH
S/&+# AREA TO BE FREED BY FREEMAIN IS NOT ON A DOUBLEWORD
BOUNDARY.
S2333 - DB) TABLE TIMESTAMP MISMATCH
ATA!"#A$DO
SB37-04 - NOT ENOUGH SPACE WAS ALLOCATED
SD37 - OUTPUT DSN USED ALL PRIMARY SPACE
SA13-14 - END OF FILE MARK DATASET NOT ON TAPE
SE37 - ALL SPACE USED ON CURRENT VOLUME. SPECIFY MORE VOLUMES
%C!" - SYNTAX, DATASET NOT FOUND ,CL - SYNTAX, DATASET NOT FOUND,
SPACE, DUPLICATE NAME, CONTENTION COULD BE ANYTHING
07D5 - I/O ERROR
2001 - CONTENTION
2005 - I/O ERROR
2004 - BAD DATA"07D#
2016 - EMPTY GENERATIONS
0406 -
44004 - S'L
013 - OPEN ERROR
028 - PAGING I/O ERROR
052-084 - INVALID CHARACTER ID
076-002 - UNABLE TO OPEN DATASET
072-053 - UNABLE TO OPEN DDNAME
0C& - PROGRAM CHECK EXCEPTIONS!
0C1 - OPERATION,
OC4 - PROTECTION/ADDRESSING,
0C5 - ADDRESSING,
0C6 - SPECIFICATION,
0C7 - DATA
706 - NON-EXECUTABLE PROGRAM
804 - INSUFFICIENT VIRTUAL STORAGE
806 - UNABLE TO LOAD "LINK ETC# PROGRAM
80A - INSUFFICIENT VIRTUAL STORAGE
852 - BAD DATA
878 - INSUFFICIENT VIRTUAL STORAGE
998 - POSSIBLE CONTENTION, TABLESPACE IN USE
737 - I/O ERROR
A14 - I/O ERROR
B37 - INSUFFICIENT DASD SPACE ON SE'UENTIAL DATASET
D37 - INSUFFICIENT DASD SPACE - NO SECONDARY SPACE ALLOCATED
E37 - INSUFFICIENT DASD SPACE ON PARTITIONED DATASET
S'! Abends
S'!CODE( -104 - ILLEGAL SYMBOL, ILLEGAL TOKEN IN S'L STATEMENT
S'!CODE( -110 - EMPTY TABLE, BAD 'UERY
S'!CODE( -180 - THE STRING REPRESENTATION OF A DATETIME VALUE
BAD DATA HAS INVALID SYNTAX
S'!CODE( -181 - THE STRING REPRESENTATION OF A DATETIME VALUE IS
BAD DATA NOT A VALID DATETIME VALUE
S'!CODE( -204 - UNDEFINED TABLE NAME - TABLE NAME DOESN1T EXIST
UNDEFINED ALIAS - ALIAS DOES NOT EXIST
S'!CODE( -305 - THE NULL VALUE CANNOT BE ASSIGNED TO OUTPUT
BECAUSE NO INDICATOR VARIABLE IS SPECIFIED
S'!CODE( -501 - CURSOR IS CLOSED DUE TO PREVIOUS CONDITIONS
S'!CODE( -551 - DOES NOT HAVE THE PRIVILEGE TO PERFORM
OPERATION DROP ALIAS ON OB,ECT
S'!CODE( -556 - CANNOT HAVE THE EXECUTE PRIVILEGE, REVOKED BY
DB)DBA BECAUSE THE REVOKEE DOES NOT POSSESS THE PRIVILEGE OR
THE REVOKER DID NOT MAKE THE GRANT
S'!CODE( -562 - A GRANT OF A PRIVILEGE WAS IGNORED BECAUSE THE
GRANTEE ALREADY HAS THE PRIVILEGE FROM THE GRANTOR
S'!CODE( -626 - THE ALTER STATEMENT IS NOT EXECUTABLE BECAUSE
PAGE SET IS NOT STOPPED - CALL DBA
S'!CODE( -803 - DATA PROBLEM - MAY BE BAD PART NUMBER COULD BE
DUPLICATE VALUES IN EXISTING ROW
S'!CODE( -805 - BIND PROBLEM
S'!CODE( -811 - ERROR ON S'L TABLE
S'!CODE( -818 - LOAD MODULE AND DBR MODULE OUT OF SYNCH NEED
TO DO BIND REPLACE OR REBIND
S'!CODE( -904 - CONTENTION
S'!CODE( -911 - CONTENTION
S'!CODE( -922 - TIME STAMP PROBLEM AFTER REBIND
S'!CODE( -923 - DB) ERROR - SOME DB) COMPONENT NOT AVAILABLE
S'!CODE( -924 - SUBSYSTEM NOT AVAIALABLE, CONTENTION IN
DATABASE
O$CODE(9 - DATA PROBLEM
O$CODE(22 - LENGTH OF RECORD VARIABLE GREATER THAN RECORD
LENGTH
O$CODE(0084 - UNDEFINED FILE CONDITION RAISE
O$CODE(1040 - SPACE PROBLEM
O$CODE(3920 - STORAGE PROBLEM
O$CODE(8094 - PROTECTION EXCEPTION - CAUSED BY BAD COMPILE -
CALL ADM, B%&"SPACE PROBLEM#
O$CODE(8097 - BAD DATA, DATA EXCEPTION
O$CODE(9050 - BAD DATA
MENSAGENS DE ERRO ENCONTRADAS EM ,OB OUTPUT1S E 'UE DEVEM
SER LEVADAS EM CONTA!
)"$*A!"D)+ )E,,O,)+ ),ESO,CE $OT A*A"!AB!E)+ )-,O.,A/ $OT
FO$D)+ )"$*A!"D ,ECO,D !E$.T0)+ )FA"!ED)+ )T"!"T1 $OT
CO/-AT"B!E)+ )DOES $OT /ATC0)+ )D-!"CATE)+ )DATASET A!,EAD1
SED)
D-!"CATE DATASET $A/E - EITHER THE PROGRAM CONTAINS TWO
DATASETS WITH THE SAME NAME, OR A DELETE UNCATALOG STEP IS NOT
WORKING
)D-!"CATE T"!"T1) A$D )E/-T1 DATASET)
E'C - E'UIPMENT CHECK
FB" - FA"!ED B1 "$"T"ATO, - CHECK THE ,CL FOR THE CAUSE OF THE
ABEND
-,OTECT"O$ E&CE-T"O$ - CAUSED BY A BAD COMPILE. CONTACT A
PROGRAMMER
O-E$ - MESSAGE STATES THAT DATASETS ARE OPEN
SE' - TAPE DRIVE PROBLEM
$AB!E TO A!!OCATE SO,T2O,3 S-ACE - NO SORTWORK SPACE
AVAILABLE. WAIT
A LITTLE WHILE UNTIL SOME ,OBS FINISH PROCESSING AND THEN
RESUBMIT THE
,OBS.
2,O$. -ASS2O,D O, ACCESS $OT A!!O2ED - MEANS THAT THE ,OB
HAS NOT A SECURITY "ACF,RACF# RULE TO EXECUTE ON THAT
SCHEDULLING TOOL OR FOR ONE DATASET, ETC.
,EASO$ CODE 00E30083 - DEADLOCK - CONTENTION
,EASO$ CODE 00D70024 - RESOURCE UNAVAILABLE
,EASO$ CODE 00E40034 - STORAGE UNAVAILABLE
,EASO$ CODE 1008 - FTP LINE DOWN
,EASO$ CODE OOE40034 - STORAGE PROBLEM - NOT ENOUGH STORAGE
S"/ - PROBLEM WITH DRIVE OR TAPE, I/O ERROR
%C! - ENVIRONMENT CHANGED. NOW UNABLE TO ALLOCATE