Scribd Logo
Upload

Welcome to Scribd!

  • 64 views

    Technical Bulletin: Subject: Powered Operation of Salalift® I Winch

    Uploaded by

    cuervohijoguacho
    DBI / SALA Salalift(r) I winch is designed and typically used for manual operation. Certain situations where the speed of the rescue, coupled with fatigue experienced by operator during long lifts, may necessitate a powered drive operation. Power drive mechanism is applied to low speed input shaft only.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Technical Bulletin: Subject: Powered Operation of Salalift® I Winch

    Uploaded by

    cuervohijoguacho
    64 views2 pages
    DBI / SALA Salalift(r) I winch is designed and typically used for manual operation. Certain situations where the speed of the rescue, coupled with fatigue experienced by operator during long lifts, may necessitate a powered drive operation. Power drive mechanism is applied to low speed input shaft only.

    Original Title

    RET001

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    DBI / SALA Salalift(r) I winch is designed and typically used for manual operation. Certain situations where the speed of the rescue, coupled with fatigue experienced by operator during long lifts, may necessitate a powered drive operation. Power drive mechanism is applied to low speed input shaft only.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    64 views2 pages

    Technical Bulletin: Subject: Powered Operation of Salalift® I Winch

    Uploaded by

    cuervohijoguacho
    DBI / SALA Salalift(r) I winch is designed and typically used for manual operation. Certain situations where the speed of the rescue, coupled with fatigue experienced by operator during long lifts, may necessitate a powered drive operation. Power drive mechanism is applied to low speed input shaft only.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 2

    F a l l P r o t e c t i o n E x p e r t s

    Page 1 of 1
    RET001
    3965 Pepin Avenue Red Wing, MN 55066- 1837 651- 388- 8282 [email protected]
    A Member of the Capital Safety Group of Companies
    Technical Bulletin No. RET001
    Subject: Powered Operation of Salalift I Winch
    The DBI/SALA Salalift I winch is designed and typically used for manual operation. Certain situations where
    the speed of the rescue, coupled with fatigue experienced by operator during long lifts, may necessitate the
    need for a powered drive operation.
    The DBI/SALA Salalift I winch may be operated by a powered drive mechanism under the following conditions.
    1. Winch is only used for raising (no lowering allowed).
    2. Power drive mechanism is applied to low speed input shaft only.
    3. Winch brakes are not removed or disabled.
    4. Maximum speed of power drive mechanism is 80 RPM's.
    5. Maximum torque of power drive mechanism is 35 foot pounds (torque limiter must be used).
    6. Proper grounding and insulation must protect electric drives.
    7. Winch gear oil must be checked monthly and changed every six months minimum.
    8. All applicable manufacturer instructions shall be followed.
    9. Manual mode to raise and lower shall remain operational after removal of powered drive mechanism.
    10. All applicable safety measures for confined spaces shall be followed. See OSHA 1910.146,
    ANSI Z117.1-1995.
    The U.L. Classification on the Salalift I winch only applies to manual operation. Winch input shaft is 1/2 inch
    square drive.
    This document was created with Win2PDF available at http://www.daneprairie.com.
    The unregistered version of Win2PDF is for evaluation or non-commercial use only.

    You might also like