2

ERROR CODE AND SELF-DIAGNOSTIC MODE

Error Code List
Jam
One of the following error codes is displayed at the upper right of the screen while pressing the
[CLEAR] button and the digital key [8] simultaneously when the CLEAR PAPER or CALL SER-
VICE symbol is blinking.
Error code Classification Contents Troubleshooting
E010 Paper exit jam Jam not reaching the exit sensor: The paper which
has passed through the fuser unit does not reach
the exit sensor.
P. 5-1
E020 Stop jam at the exit sensor: The trailing edge of the
paper does not pass the exit sensor after its leading
edge has reached this sensor.
P. 5-1
E030 Other paper jam Power-ON jam: The paper is remaining on the
paper transport path when power is turned ON.
P. 5-2
E061 Incorrect paper size setting for upper drawer: The
size of paper in the 1st drawer differs from size set-
ting of the equipment.
P. 5-2
E062 Incorrect paper size setting for lower drawer: The
size of paper in the 2nd drawer differs from size set-
ting of the equipment.
P. 5-2
E063 Incorrect paper size setting for PFP upper drawer:
The size of paper in the 3rd drawer differs from size
setting of the equipment.
P. 5-2
E064 Incorrect paper size setting for PFP lower drawer:
The size of paper in the 4th drawer differs from size
setting of the equipment.
P. 5-2
E065 Incorrect paper size setting for bypass tray: The
size of paper in the bypass tray differs from size
setting of the equipment.
P. 5-2
E090 HDD abnormality causes jam: Image data to be
printed cannot be prepared.
P. 5-3
E110 Paper misfeeding ADU misfeeding (Paper not reaching the 1st trans-
port sensor): The paper which has passed through
ADU does not reach the 1st transport sensor during
duplex printing.
P. 5-15
E120 Bypass misfeeding (Paper not reaching the 1st
transport sensor): The paper fed from the bypass
tray does not reach the 1st transport sensor.
P. 5-16
E130 Upper drawer misfeeding (Paper not reaching the
1st transport sensor): The paper fed from the upper
drawer does not reach the 1st transport sensor.
P. 5-17
E140 Lower drawer misfeeding (Paper not reaching the
2nd transport sensor): The paper fed from the lower
drawer does not reach the 2nd transport sensor.
P. 5-18
E150 PFP upper drawer misfeeding (Paper not reaching
the PFP upper drawer feed sensor): The paper fed
from the PFP upper drawer does not reach the PFP
upper drawer feed sensor.
P. 5-19
e-STUDIO200L/202L/230/232/280/282
ERROR CODE AND SELF-DIAGNOSTIC MODE
E160 Paper misfeeding PFP lower drawer misfeeding (Paper not reaching
the PFP lower drawer feed sensor): The paper fed
from the PFP lower drawer does not reach the PFP
lower drawer feed sensor.
P. 5-20
E190 LCF misfeeding (Paper not reaching the LCF feed
sensor): The paper fed from the LCF does not
reach the LCF feed sensor.
P. 5-21
E200 Paper transport jam Upper drawer transport jam (Paper not reaching the
registration sensor): The paper does not reach the
registration sensor after it has passed the 1st trans-
port sensor.
P. 5-3
E210 Lower drawer transport jam (Paper not reaching the
registration sensor): The paper does not reach the
registration sensor after it has passed the 1st trans-
port sensor.
P. 5-3
E220 Lower drawer transport jam (Paper not reaching the
1st transport sensor): The paper does not reach the
1st transport sensor after it has passed the lower
drawer feed sensor.
P. 5-4
E270 Bypass transport jam (paper not reaching the regis-
tration sensor): The paper does not reach the regis-
tration sensor after it has passed the 1st transport
sensor.
P. 5-5
E280 ADU transport jam (paper not reaching the registra-
tion sensor): The paper which has passed through
ADU and the 1st transport sensor does not reach
the registration sensor during duplex printing.
P. 5-5
E300 PFP upper drawer transport jam (Paper not reach-
ing the registration sensor): The paper does not
reach the registration sensor after it has passed the
1st transport sensor.
P. 5-3
E310 PFP upper drawer transport jam (Paper not reach-
ing the 1st transport sensor): The paper does not
reach the 1st transport sensor after it has passed
the 2nd transport sensor.
P. 5-4
E320 PFP upper drawer transport jam (Paper not reach-
ing the 2nd transport sensor): The paper does not
reach the 2nd transport sensor after it has passed
the PFP upper drawer feed sensor.
P. 5-6
E330 PFP lower drawer transport jam (Paper not reach-
ing the registration sensor): The paper does not
reach the registration sensor after it has passed the
1st transport sensor.
P. 5-3
E340 PFP lower drawer transport jam (Paper not reach-
ing the 1st transport sensor): The paper does not
reach the 1st transport sensor after it has passed
the PFP lower drawer feed sensor.
P. 5-4
E350 PFP lower drawer transport jam (Paper not reach-
ing the 2nd transport sensor): The paper does not
reach the 2nd transport sensor after it has passed
the PFP upper drawer feed sensor.
P. 5-6
E360 PFP lower drawer transport jam (Paper not reach-
ing the PFP upper drawer feed sensor): The paper
does not reach the PFP upper drawer feed sensor
after it has passed the PFP lower drawer feed sen-
sor.
P. 5-7
Error code Classification Contents Troubleshooting
2
E3C0 Paper transport jam LCF transport jam (Paper not reaching the registra-
tion sensor): The paper does not reach the registra-
tion sensor after it has passed the 1st transport
sensor.
P. 5-3
E3D0 LCF transport jam (Paper not reaching the 1st
transport sensor): The paper does not reach the 1st
transport sensor after it has passed the 2nd trans-
port sensor.
P. 5-4
E3E0 LCF transport jam (Paper not reaching the 2nd
transport sensor): The paper does not reach the
2nd transport sensor after it has passed the LCF
feed sensor.
P. 5-6
E400 Cover open jam Transfer cover open jam: The transfer cover has
opened during printing.
P. 5-22
E410 Front cover open jam: The front cover has opened
during printing.
P. 5-23
E420 PFP side cover open jam: The PFP side cover has
opened during printing.
P. 5-24
E430 ADU open jam: The ADU has opened during print-
ing.
P. 5-25
E440 Side cover open jam: The side cover has opened
during printing.
P. 5-25
E450 LCF side cover open jam: The LCF side cover has
opened during printing.
P. 5-26
E480 Bridge unit open jam: The bridge unit has opened
during printing.
P. 5-26
E490 Job separator cover open jam: The job separator
cover has opened during printing.
P. 5-27
E491 Offset tray cover open jam: The offset tray cover
has opened during printing.
P. 5-27
E510 Paper transport jam
(ADU section)
Stop jam in the ADU: The paper does not reach the
ADU exit sensor after it has passed the ADU
entrance sensor.
P. 5-8
E520 Jam not reaching the ADU entrance sensor: The
paper does not reach the ADU entrance sensor
after it is switchbacked in the exit section.
P. 5-9
E550 Other paper jam Paper remaining jam on the transport path: The
paper is remaining on the transport path when print-
ing is finished (caused by a multiple paper feeding).
P. 5-10
Error code Classification Contents Troubleshooting
e-STUDIO200L/202L/230/232/280/282d
ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 4
E711 RADF jam Jam not reaching the original length sensor: The
original fed from the original feeding tray does not
reach the original length sensor.
P. 5-28
E712 Jam not reaching the registration sensor: The origi-
nal fed from the original feeding tray does not reach
the registration sensor.
P. 5-28
E713 Stop jam at the original length sensor: The trailing
edge of the original does not pass the original
length sensor after its leading edge has reached
this sensor.
P. 5-28
E714 Feed signal reception jam: The feed signal is
received even no original exists on the original
feeding tray.
P. 5-29
E721 Jam not reaching the read sensor: The original
does not reach the read sensor after it has passed
the registration sensor (when scanning obverse
side) or the reverse sensor (when scanning reverse
side).
P. 5-29
E722 Jam not reaching the exit sensor (during scanning):
The original which passed the read sensor does not
reach the exit sensor when it is transported from the
scanning section to exit section.
P. 5-30
E723 Jam not reaching the reverse sensor (during scan-
ning): The original which passed the read sensor
does not reach the reverse sensor when it is trans-
ported from the scanning section to reverse section.
P. 5-30
E724 Stop jam at the registration sensor: The trailing
edge of the original does not pass the registration
sensor after its leading edge has reached this sen-
sor.
P. 5-30
E725 Stop jam at the read sensor: The trailing edge of the
original does not pass the read sensor after its lead-
ing edge has reached this sensor.
P. 5-31
E726 Transport/exit signal reception jam: RADF receives
the transport/exit reception signal from the equip-
ment when no original is at the exposure waiting
position.
P. 5-31
E731 Stop jam at the exit sensor: The trailing edge of the
original does not pass the exit sensor after its lead-
ing edge has reached this sensor.
P. 5-32
E741 Stop jam at the reverse sensor: The trailing edge of
the original does not pass the reversal sensor after
its leading edge has reached this sensor.
P. 5-32
E742 Jam not reaching the reverse sensor (during
reverse feeding): The leading edge of the original
does not reach the reverse sensor when original is
fed from the reverse section.
P. 5-33
E743 Jam not reaching the exit sensor (during reverse
feeding): The original does not reach the exit sen-
sor after it has passed the reverse sensor when the
original is exited from the reverse section.
P. 5-33
E860 RADF jam access cover open: The RADF jam
access cover has opened during RADF operation.
P. 5-34
E870 RADF open jam: RADF has opened during RADF
operation.
P. 5-34
Error code Classification Contents Troubleshooting
June 2004 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO200L/202L/230/232/280/282
ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 5
2
E910 Finisher jam
(Bridge unit)
Jam at the bridge unit transport sensor-1: The
paper does not reach the bridge unit transport sen-
sor-1 after it has passed the exit sensor.
P. 5-35
E920 Stop jam at the bridge unit transport sensor-1: The
trailing edge of the paper does not pass the bridge
unit transport sensor-1 after its leading edge has
reached the sensor.
P. 5-35
E930 Jam at the bridge unit transport sensor-2: The trail-
ing edge of the paper does not reach the bridge unit
transport sensor-2 after its leading edge has
reached the bridge unit transport sensor-1.
P. 5-35
E940 Stop jam at the bridge unit transport sensor-2: The
trailing edge of the paper does not reach the bridge
unit transport sensor-2 after its leading edge has
reached the bridge unit transport sensor-2.
P. 5-35
E950 Job separator jam Jam not reaching the job separator transport sen-
sor: The paper has passed through the exit sensor
does not reach the job separator transport sensor.
P. 5-11
E951 Stop jam at the job separator transport sensor: The
trailing edge of the paper does not pass the job sep-
arator transport sensor.
P. 5-11
E960 Offset tray jam Jam not reaching the offset tray transport sensor:
The paper has passed through the exit sensor does
not reach the offset tray transport sensor.
P. 5-11
E961 Stop jam at the offset tray transport sensor: The
trailing edge of the paper does not pass the offset
tray transport sensor.
P. 5-11
E9F0 Finisher jam
(Puncher unit)
Punching jam: Punching is not performed properly.
[MJ-1025 (When MJ-6005 is installed)]
P. 5-36
EA10 Finisher jam
(Finisher unit)
Paper transport delay jam: The paper which has
passed the bridge unit does not reach the inlet sen-
sor. [MJ-1022/1025]
P. 5-37
EA20 Paper transport stop jam: The paper does not pass
through the inlet sensor. [MJ-1022/1025]
P. 5-38
EA30 Power-ON jam: Paper exists at the inlet sensor
when power is turned ON. [MJ-1022/1025]
P. 5-39
EA40 Door open jam: The finisher has been released
from the equipment during printing. [MJ-1022/1025]
P. 5-40
EA50 Stapling jam: Stapling is not performed properly.
[MJ-1022/1025]
P. 5-41
EA60 Early arrival jam: The inlet sensor detects the paper
earlier than a specified timing. [MJ-1022]
P. 5-42
EA70 Stack delivery jam: It cannot deliver the stack of
paper on the intermediary process tray to the stack
tray. [MJ-1022/1025]
P. 5-43
EAB0 Finisher jam
(Saddle Stitcher sec-
tion)
Saddle paper transport stop jam: The paper which
passed through the inlet sensor does not reach or
pass through the folding position sensor. [MJ-1025]
P. 5-45
EAC0 Saddle transport delay jam: The paper which has
reached the inlet sensor does not pass through this
sensor. [MJ-1025]
P. 5-45
EAD0 Other paper jam Print end command time-out jam: The printing has
not finished normally because of the communica-
tion error between the SYS board and LGC board
at the end of printing.
P. 5-46
Error code Classification Contents Troubleshooting
e-STUDIO200L/202L/230/232/280/282 June 2004 TOSHIBA TEC CORPORATION All rights reserved
ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 6
EAE0 Finisher jam Receiving time time-out jam: The printing has been
interrupted because of the communication error
between the equipment and finisher when the
paper is transported from the equipment to the fin-
isher.
P. 5-46
EAF0 Finisher jam
(Finisher unit)
Stack return jam: It cannot load the paper which
passed through the delivery roller on the intermedi-
ary process tray. [MJ-1022]
P. 5-44
EB30 Finisher jam Ready time time-out jam: The equipment judges
that the paper transport to the finisher is disabled
because of the communication error between the
equipment and finisher at the start of printing.
P. 5-46
EB50 Paper transport jam Paper remaining on the transport path: The multiple
feeding of preceding paper caused the misfeeding
of upcoming paper.
P. 5-12
EB60 Paper remaining on the transport path: The multiple
feeding of preceding paper caused the misfeeding
of upcoming paper (redetection after no jam is
detected at [EB50]).
P. 5-14
Error code Classification Contents Troubleshooting
June 2004 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO200L/202L/230/232/280/282
ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 7
2
2.1.2 Service call
Error code Classification Contents Troubleshooting
C010 Drive system
related service call
Main motor abnormality: The main motor is not rotating
normally.
P. 5-47
C040 Paper feeding sys-
tem related ser-
vice call
PFP motor abnormality: The PFP motor is not rotating
normally.
P. 5-48
C130 Upper drawer tray abnormality: The upper drawer tray
motor is not rotating or the upper drawer tray is not mov-
ing normally.
P. 5-49
C140 Lower drawer tray abnormality: The lower drawer tray
motor is not rotating or the lower drawer tray is not mov-
ing normally.
P. 5-49
C150 PFP upper drawer tray abnormality: The PFP upper
drawer tray motor is not rotating or the PFP upper drawer
tray is not moving normally.
P. 5-50
C160 PFP lower drawer tray abnormality: The PFP lower
drawer tray motor is not rotating or the PFP lower drawer
tray is not moving normally.
P. 5-50
C180 LCF tray-up motor abnormality: The LCF tray-up motor is
not rotating or the LCF tray is not moving normally.
P. 5-51
C1A0 LCF end fence motor abnormality: The LCF end fence
motor is not rotating or the LCF end fence is not moving
normally.
P. 5-52
C1B0 LCF transport motor abnormality: The LCF transport
motor is not rotating normally.
P. 5-53
C260 Scanning system
related service call
Peak detection error: Lighting of the exposure lamp
(white reference) is not detected when power is turned
ON.
P. 5-54
C270 Carriage home position sensor not turning OFF within a
specified period of time: The carriage does not shift from
its home position in a specified period of time.
P. 5-55
C280 Carriage home position sensor not turning ON within a
specified period of time: The carriage does not reach to
its home position in a specified period of time.
P. 5-55
C410 Fuser unit related
service call
Thermistor or heater abnormality at power-ON: Abnor-
mality of service call the thermistor is detected when
power is turned ON or the temperature of the fuser roller
does not rise in a specified period of time after power is
turned ON.
P. 5-56
C430 Thermistor abnormality after abnormality judgment:
Abnormality of the thermistor is detected after a specified
period of time has passed from power-ON (including
ready state).
P. 5-57
C440 Heater abnormality after abnormality judgment: The tem-
perature of the fuser roller has exceeded the range of
control (in this case, the main switch turns OFF automati-
cally) or does not even reach the range.
P. 5-57
C450 Thermistor abnormality during printing: Abnormality of the
thermistor is detected during printing.
P. 5-57
C550
(C780)
Optional communi-
cation related ser-
vice call
RADF I/F error: Communication error has occurred
between the RADF and the scanner.
P. 5-58
C570 Communication error between Engine-CPU and IPC
board
P. 5-58
C580 Communication error between IPC board and finisher P. 5-58
07/04
e-STUDIO200L/202L/230/232/280/282 June 2004 TOSHIBA TEC CORPORATION All rights reserved
ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 8
C730 RADF related ser-
vice call
EEPROM initialization error: EEPROM is not initialized
normally when performing the code 05-356.
P. 5-59
C740 Reverse sensor adjustment error P. 5-59
C810 Fan motor abnormality: The fan motor is not rotating nor-
mally.
P. 5-59
C820 Read sensor adjustment error: The read sensor cannot
be adjusted normally when performing the code 05-356.
P. 5-59
C830 Original length sensor adjustment error: The original
length sensor cannot be adjusted normally when per-
forming the code 05-356.
P. 5-59
C940 Circuit related ser-
vice call
Engine-CPU abnormality P. 5-76
C970 Process related
service call
High-voltage transformer abnormality: Leakage of the
main charger is detected.
P. 5-76
CA10 Laser optical unit
related service call
Polygonal motor abnormality: The polygonal motor is not
rotating normally.
P. 5-60
CA20 H-Sync detection error: H-Sync detection PC board can-
not detect laser beams.
P. 5-60
CB10 Finisher related
service call
Transport motor abnormality: The transport motor or
stack transport roller is not rotating normally. [MJ-1025]
P. 5-61
CB20 Delivery motor abnormality: Delivery motor or delivery
roller is not rotating normally. [MJ-1022/1025]
P. 5-62
CB30 Tray lift motor abnormality: The tray lift motor is not rotat-
ing normally or the delivery tray is not moving normally.
[MJ-1025]
P. 5-63
CB50 Staple motor (staple/fold) abnormality: The staple motor
is not rotating normally or the stapler is not moving nor-
mally. [MJ-1025]
P. 5-64
CB60 Stapler unit shift motor abnormality: The stapler unit shift
motor is not rotating normally or the Stapler Unit is not
moving normally. [MJ-1025]
P. 5-66
CB80 Backup RAM data abnormality:
1) Abnormality of checksum value on finisher controller
board is detected when the power is turned on.
[MJ-1025]
2) Abnormality of checksum value on punch controller
board is detected when the power is turned on.
[MJ-1025 (when MJ-6005 is installed)]
P. 5-67
CC30 Stack processing motor abnormality: The stack process-
ing motor is not rotating normally or the stack delivery belt
is not moving normally. [MJ-1022]
Paddle motor abnormality: The paddle motor is not rotat-
ing normally or the swing guide is not moving normally.
[MJ-1025]
P. 5-67
CC50 Horizontal registration motor abnormality: The horizontal
registration motor is not rotating normally or the puncher
is not moving normally.
[MJ-1025 (when MJ-6005 is installed)]
P. 5-69
CC60 Punch motor abnormality: The punch motor is not rotating
normally or the puncher is not moving normally.
[MJ-1025 (when MJ-6005 is installed)]
P. 5-69
CC80 Front jogging motor abnormality: Front jogging motor is
not rotating normally or the front alignment plate is not
moving normally. [MJ-1022]
Alignment motor (front) abnormality: The alignment motor
(front) is not rotating normally or the front alignment plate
is not moving normally. [MJ-1025]
P. 5-70
CC90 Upper stack tray lift motor abnormality: The upper stack
tray lift motor is not rotating or the upper stack tray is not
moving normally. [MJ-1022]
P. 5-71
Error code Classification Contents Troubleshooting
06/09
June 2004 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO200L/202L/230/232/280/282
ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 9
2
CCA0 Finisher related
service call
Lower stack tray lift motor abnormality: The lower stack
tray lift motor is not rotating or the lower stack tray is not
moving normally. [MJ-1022]
P. 5-72
CCB0 Rear jogging motor abnormality: Rear jogging motor is
not rotating normally or the rear alignment plate is not
moving normally. [MJ-1022]
Alignment motor (rear) abnormality: The alignment motor
(rear) is not rotating normally or the rear alignment plate
is not moving normally. [MJ-1025]
P. 5-73
CDC0 Punch power failure abnormality: 24 V is not applied to
the punch controller board.
[MJ-1025 (when MJ-6005 is installed)]
P. 5-74
CDD0 Folding position sensor abnormality: Automatic adjust-
ment of the folding position sensor can not be performed
properly. [MJ-1025]
P. 5-74
CDE0 Paddle motor abnormality: The paddle motor does not
rotate properly. [MJ-1025]
P. 5-75
CDF0 Offset tray related
service call
Initialization error of the offset tray: The home position of
the separator cannot be detected when the power is
turned ON.
P. 5-76
CE00 Finisher related
service call
Communication error between finisher unit and puncher
unit: Communication error between the finisher controller
PC board and punch controller PC board.
[MJ-1025 (when MJ-6005 is installed)]
P. 5-75
CF60 Other service call Toner for recycle transport area lock P. 5-76
F070 Communication
related service call
Communication error between System-CPU and Engine-
CPU
P. 5-58
F090 Other service call SRAM abnormality on the SYS board P. 5-76
F091 NVRAM abnormality on the SYS board P. 5-77
F092 SRAM and NVRAM abnormality on the SYS board P. 5-77
F100 HDD format error: HDD cannot be initialized normally. P. 5-77
F101 HDD unmounted: Connection of HDD cannot be
detected.
P. 5-77
F102 HDD start error: HDD cannot become Ready state. P. 5-77
F103 HDD transfer time-out: Reading/writing cannot be per-
formed in the specified period of time.
P. 5-77
F104 HDD data error: Abnormality is detected in the data of
HDD.
P. 5-77
F105 HDD other error P. 5-77
F106 Point and Print partition damage P. 5-78
F107 /SHR partition damage P. 5-78
F108 /SHA partition damage P. 5-78
F110 Communication
related service call
Communication error between System-CPU and Scan-
ner-CPU
P. 5-58
F111 Scanner response abnormality P. 5-58
F120 Other service call Database abnormality: Database is not operating nor-
mally.
P. 5-78
F130 Invaid MAC address P. 5-78
F200 Data overwrite kit (GP-1050/1060) is taken off P. 5-78
Error code Classification Contents Troubleshooting
e-STUDIO200L/202L/230/232/280/282 June 2004 TOSHIBA TEC CORPORATION All rights reserved
ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 10
2.1.3 Error in Internet FAX / Scanning Function
1) Internet FAX related error
(when GM-1020/3020, 1030/3030, 2020 or 2030 is installed (e-STUDIO200L/230/280))
(when GM-1070/4070, 1080U/4080U, 2070 or 2080U is installed (e-STUDIO202L/232/282))
Error code Contents Troubleshooting
1C10 System access abnormality P. 5-79
1C11 Insufficient memory P. 5-79
1C12 Message reception error P. 5-79
1C13 Message transmission error P. 5-79
1C14 Invalid parameter P. 5-79
1C15 Exceeding file capacity P. 5-79
1C20 System management module access abnormality P. 5-79
1C21 Job control module access abnormality P. 5-79
1C22 Job control module access abnormality P. 5-79
1C30 Directory creation failure P. 5-80
1C31 File creation failure P. 5-80
1C32 File deletion failure P. 5-79
1C33 File access failure P. 5-80
1C40 Image conversion abnormality P. 5-80
1C60 HDD full failure during processing P. 5-80
1C61 Address Book reading failure P. 5-80
1C62 Memory acquiring failure P. 5-80
1C63 Terminal IP address unset P. 5-80
1C64 Terminal mail address unset P. 5-80
1C65 SMTP address unset P. 5-80
1C66 Server time time-out error P. 5-80
1C67 NIC time time-out error P. 5-80
1C68 NIC access error P. 5-80
1C69 SMTP server connection error P. 5-81
1C6A HOST NAME error P. 5-81
1C6B Terminal mail address error P. 5-81
1C6C Destination mail address error P. 5-81
1C6D System error P. 5-80
1C70 SMTP client OFF P. 5-81
1C71 SMTP authentication error P. 5-81
1C72 POP before SMTP error P. 5-81
1C80 Internet FAX transmission failure when processing E-mail job received P. 5-81
1C81 Onramp Gateway transmission failure P. 5-81
1C82 Internet FAX transmission failure when processing FAX job received P. 5-81
1CC0 Job canceling -
1CC1 Power failure P. 5-81
05/11
June 2004 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO200L/202L/230/232/280/282
ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 11
2
2) RFC related error
(when GM-1020/3020, 1030/3030, 2020 or 2030 is installed (e-STUDIO200L/230/280))
(when GM-1070/4070, 1080U/4080U, 2070 or 2080U is installed (e-STUDIO202L/232/282))
Error code
Message displayed in the
TopAccess screen
Contents Troubleshooting
2500 Syntax error, command unrecog-
nized
HOST NAME error (RFC: 500)
Destination mail address error
(RFC: 500)
Terminal mail address error
(RFC: 500)
P. 5-82
2501 Syntax error in parameters or
arguments
HOST NAME error (RFC: 501)
Destination mail address error
(RFC: 501)
Terminal mail address error
(RFC: 501)
P. 5-82
2503 Bad sequence of commands Destination mail address error
(RFC: 503)
P. 5-82
2504 Command parameter not imple-
mented
HOST NAME error (RFC: 504) P. 5-82
2550 Mailbox unavailable Destination mail address error
(RFC: 550)
P. 5-82
2551 User not local Destination mail address error
(RFC: 551)
P. 5-82
2552 Insufficient system storage Terminal/Destination mail address error
(RFC: 552)
P. 5-82
2553 Mailbox name not allowed Destination mail address error
(RFC: 553)
P. 5-82
05/11
e-STUDIO200L/202L/230/232/280/282 June 2004 TOSHIBA TEC CORPORATION All rights reserved
ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 12
3) Electronic Filing related error
Error code
Message displayed in the
TopAccess screen
Contents Troubleshooting
2B10 There was no applicable job. No applicable job error in job control
module
P. 5-83
2B11 Job status failed. JOB status abnormality P. 5-83
2B20 Failed to access file. File library function error P. 5-83
2B30 Insufficient disk space. Insufficient disk space in /SHR partition P. 5-83
2B31 Failed to access Electronic Filing. Status of specified Electronic Filing or
folder is undefined or being created/
deleted
P. 5-83
2B32 Failed to print Electronic Filing
document.
Electronic Filing printing failure:
Specified document can not be printed
because of client's access (being edited,
etc.).
P. 5-83
2B50 Failed to process image. Image library error P. 5-83
2B51 Failed to process print image. List library error P. 5-83
2B71 Document(s) expire(s) in a few
days
Documents expiring in a few days exist -
2B80 Hard Disk space for Electronic
Filing nearly full.
Hard disk space in /SHR partition is
nearly full (90%).
-
2B90 Insufficient Memory. Insufficient memory capacity P. 5-83
2BA0 Invalid Box password specified. Invalid Box password P. 5-84
2BB0 Job canceled Job canceling -
2BB1 Power failure occurred Power failure P. 5-84
2BC0 System fatal error. Fatal failure occurred. P. 5-83
2BC1 Failed to acquire resource. System management module resource
acquiring failure
P. 5-83
2BD0 Power failure occurred during e-
Filing restoring.
Power failure occurred during restoring
of Electronic Filing
P. 5-84
2BE0 Failed to get machine parameter. Machine parameter reading failure P. 5-84
2BF0 Maximum number of pages has
been exceeded (list Maximum)
Exceeding maximum number of pages P. 5-84
2BF1 Maximum number of documents
has been exceeded (list Maxi-
mum)
Exceeding maximum number of docu-
ments
P. 5-84
2BF2 Maximum number of folders has
been exceeded (list Maximum)
Exceeding maximum number of folders P. 5-84
June 2004 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO200L/202L/230/232/280/282
ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 13
2
4) E-mail related error
(when GM-1020/3020, 1030/3030, 2020 or 2030 is installed (e-STUDIO200L/230/280))
(when GM-1070/4070, 1080U/4080U, 2070 or 2080U is installed (e-STUDIO202L/232/282))
Error code
Message displayed in the
TopAccess screen
Contents Troubleshooting
2C10 Illegal Job status System access abnormality P. 5-85
2C11 Not enough memory Insufficient memory P. 5-85
2C12 Illegal Job status Message reception error P. 5-85
2C13 Illegal Job status Message transmission error P. 5-85
2C14 Invalid parameter specified Invalid parameter P. 5-85
2C15 Message size exceeded limit or
maximum size
Exceeding file capacity P. 5-85
2C20 Illegal Job status System management module access
abnormality
P. 5-85
2C21 Illegal Job status Job control module access abnormality P. 5-85
2C22 Illegal Job status Job control module access abnormality P. 5-85
2C30 Failed to create directory Directory creation failure P. 5-85
2C31 Failed to create file File creation failure P. 5-85
2C32 Failed to delete file File deletion failure P. 5-85
2C33 Failed to create file File access failure P. 5-85
2C40 Failed to convert image file for-
mat
Image conversion abnormality P. 5-85
2C60 Failed to process your Job. Insuf-
ficient disk space.
HDD full failure during processing P. 5-86
2C61 Failed to read AddressBook Address Book reading failure P. 5-86
2C62 Not enough memory Memory acquiring failure P. 5-85
2C63 Invalid Domain Address Terminal IP address unset P. 5-86
2C64 Invalid Domain Address Terminal mail address unset P. 5-86
2C65 Failed to connect to SMTP server SMTP address unset P. 5-86
2C66 Failed to connect to SMTP server Server time time-out error P. 5-86
2C67 Failed to send E-Mail message NIC time time-out error P. 5-86
2C68 Failed to send E-Mail message NIC access error P. 5-86
2C69 Failed to connect to SMTP server SMTP server connection error P. 5-86
2C6A Failed to send E-Mail message HOST NAME error (No RFC error) P. 5-86
2C6B Invalid address specified in From:
field
Terminal mail address error P. 5-86
2C6C Invalid address specified in To:
field
Destination mail address error (No RFC
error)
P. 5-87
2C6D NIC system error System error P. 5-86
2C70 SMTP service is not available SMTP client OFF P. 5-87
2C71 Failed SMTP Authentication SMTP authentication error P. 5-87
2C72 POP Before SMTP Authentica-
tion Failed
POP before SMTP error P. 5-87
2C80 Failed to process received E-mail
job
E-mail transmission failure when pro-
cessing E-mail job received
P. 5-87
2C81 Failed to process received Fax
job
Process failure of FAX job received P. 5-87
2CC0 Job canceled Job canceling -
2CC1 Power failure occurred Power failure P. 5-87
05/11
e-STUDIO200L/202L/230/232/280/282 June 2004 TOSHIBA TEC CORPORATION All rights reserved
ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 14
5) File sharing related error
(when GM-1020/3020, 1030/3030, 2020 or 2030 is installed (e-STUDIO200L/230/280))
(when GM-1070/4070, 1080U/4080U, 2070 or 2080U is installed (e-STUDIO202L/232/282))
Error code
Message displayed in the
TopAccess screen
Contents Troubleshooting
2D10 Illegal Job status System access abnormality P. 5-88
2D11 Not enough memory Insufficient memory P. 5-88
2D12 Illegal Job status Message reception error P. 5-88
2D13 Illegal Job status Message transmission error P. 5-88
2D14 Invalid parameter specified Invalid parameter P. 5-88
2D15 There are too many documents in
the folder. Failed in creating new
document.
Exceeding document number P. 5-88
2D20 Illegal Job status System management module access
abnormality
P. 5-88
2D21 Illegal Job status Job control module access abnormality P. 5-88
2D22 Illegal Job status Job control module access abnormality P. 5-88
2D30 Failed to create directory Directory creation failure P. 5-88
2D31 Failed to create file File creation failure P. 5-88
2D32 Failed to delete file File deletion failure P. 5-88
2D33 Failed to create file File access failure P. 5-88
2D40 Failed to convert image file for-
mat
Image conversion abnormality P. 5-89
2D60 Failed to copy file File library access abnormality P. 5-88
2D61 Invalid parameter specified Invalid parameter P. 5-88
2D62 Failed to connect to network des-
tination. Check destination path
File server connection error P. 5-89
2D63 Specified network path is invalid.
Check destination path
Invalid network path P. 5-89
2D64 Logon to file server failed. Check
username and password
Login failure P. 5-89
2D65 There are too many documents in
the folder. Failed in creating new
document.
Exceeding documents in folder: Creating
new document is failed.
P. 5-89
2D66 Failed to process your Job. Insuf-
ficient disk space.
HDD full failure during processing P. 5-89
2D67 FTP service is not available FTP service not available P. 5-89
2D68 File Sharing service is not avail-
able
File sharing service not available P. 5-89
2DA0 Expired scan documents deleted
from share folder.
Periodical deletion of scanned docu-
ments completed properly.
-
2DA1 Expired Sent Fax documents
deleted from shared folder.
Periodical deletion of transmitted FAX
documents completed properly.
-
2DA2 Expired Received Fax documents
deleted from shared folder.
Periodical deletion of received FAX doc-
uments completed properly.
-
2DA3 Scanned documents in shared
folder deleted upon user's
request.
Manual deletion of scanned documents
completed properly.
-
2DA4 Sent Fax Documents in shared
folder deleted upon user's
request.
Manual deletion of transmitted FAX doc-
uments completed properly.
-
2DA5 Received Fax Documents in
shared folder deleted upon user's
request.
Manual deletion of received FAX docu-
ments completed properly.
-
2DA6 Failed to delete file. File deletion failure P. 5-88
05/11
June 2004 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO200L/202L/230/232/280/282
ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 15
2
2DA7 Failed to acquire resource. Resource acquiring failure P. 5-88
2DC0 Job canceled Job canceling -
2DC1 Power failure occurred Power failure P. 5-89
Error code
Message displayed in the
TopAccess screen
Contents Troubleshooting
e-STUDIO200L/202L/230/232/280/282 June 2004 TOSHIBA TEC CORPORATION All rights reserved
ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 16
6) E-mail reception related error
(when GM-1020/3020, 1030/3030, 2020 or 2030 is installed (e-STUDIO200L/230/280))
(when GM-1070/4070, 1080U/4080U, 2070 or 2080U is installed (e-STUDIO202L/232/282))
Error code
Message displayed in the
TopAccess screen
Contents Troubleshooting
3A10 MIME Error has been detected in
the received mail.
E-mail MIME error P. 5-90
3A11 MIME Error has been detected in
the received mail. This mail has
been transferred to the adminis-
trator.
P. 5-90
3A12 MIME Error has been detected in
the received mail. This mail could
not be transferred to the adminis-
trator.
P. 5-90
3A20 Analyze Error has been detected
in the received mail.
E-mail analysis error P. 5-90
3A21 Analyze Error has been detected
in the received mail. This mail
has been transferred to the
administrator.
P. 5-90
3A22 Analyze Error has been detected
in the received mail. This mail
could not be transferred to the
administrator.
P. 5-90
3A30 Whole partial mails were not
reached by timeout.
Partial mail time-out error P. 5-90
3A40 Partial Mail Error has been
detected in the received mail.
Partial mail related error P. 5-90
3A50 HDD Full Error has been
occurred in this mail.
Insufficient HDD capacity error P. 5-90
3A51 HDD Full Error has been
occurred in this mail. This mail
has been transferred to the
administrator.
P. 5-90
3A52 HDD Full Error has been
occurred in this mail. This mail
could not be transferred to the
administrator.
P. 5-90
3A60 HDD Full Warning has been
occurred in this mail.
Warning of insufficient HDD capacity P. 5-90
3A61 HDD Full Warning has been
occurred in this mail. This mail
could not be transferred to the
administrator.
P. 5-90
3A62 HDD Full Warning has been
occurred in this mail. This mail
could not be transferred to the
administrator.
P. 5-90
3A70 Receiving partial mail was
aborted since the partial mail set-
ting has been changed to Dis-
able.
Warning of partial mail interruption P. 5-90
05/11
June 2004 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO200L/202L/230/232/280/282
ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 17
2
3A80 Partial mail was received during
the partial mail setting is disabled.
Partial mail reception setting OFF P. 5-90
3A81 Partial mail was received during
the partial mail setting is disabled.
This mail has been transferred to
the administrator.
P. 5-90
3A82 Partial mail was received during
the partial mail setting is disabled.
This mail could not be transferred
to the administrator.
P. 5-90
3B10 Format Error has been detected
in the received mail.
E-mail format error P. 5-90
3B11 Format Error has been detected
in the received mail. This mail
has been transferred to the
administrator.
P. 5-90
3B12 Format Error has been detected
in the received mail. This mail
could not be transferred to the
administrator.
P. 5-90
3B20 Content-Type Error has been
detected in the received mail.
Content-Type error P. 5-90
3B21 Content-Type Error has been
detected in the received mail.
This mail has been transferred to
the administrator.
P. 5-90
3B22 Content-Type Error has been
detected in the received mail.
This mail could not be transferred
to the administrator.
P. 5-90
3B30 Charset Error has been detected
in the received mail.
Charset error P. 5-90
3B31 Charset Error has been detected
in the received mail. This mail
has been transferred to the
administrator.
P. 5-90
3B32 Charset Error has been detected
in the received mail. This mail
could not be transferred to the
administrator.
P. 5-90
3B40 Decode Error has been detected
in the received mail.
E-mail decode error P. 5-90
3B41 Decode Error has been detected
in the received mail. This mail
has been transferred to the
administrator.
P. 5-90
3B42 Decode Error has been detected
in the received mail. This mail
could not be transferred to the
administrator.
P. 5-90
Error code
Message displayed in the
TopAccess screen
Contents Troubleshooting
e-STUDIO200L/202L/230/232/280/282 June 2004 TOSHIBA TEC CORPORATION All rights reserved
ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 18
3C10 Tiff Analyze Error has been
detected in the received mail.
TIFF analysis error P. 5-91
3C11 Tiff Analyze Error has been
detected in the received mail.
This mail has been transferred to
the administrator.
P. 5-91
3C12 Tiff Analyze Error has been
detected in the received mail.
This mail could not be transferred
to the administrator.
P. 5-91
3C13 Tiff Analyze Error has been
detected in the received mail.
P. 5-91
3C20 Tiff Compression Error has been
detected in the received mail.
TIFF compression error P. 5-91
3C21 Tiff Compression Error has been
detected in the received mail.
This mail has been transferred to
the administrator.
P. 5-91
3C22 Tiff Compression Error has been
detected in the received mail.
This mail could not be transferred
to the administrator.
P. 5-91
3C30 Tiff Resolution Error has been
detected in the received mail.
TIFF resolution error P. 5-91
3C31 Tiff Resolution Error has been
detected in the received mail.
This mail has been transferred to
the administrator.
P. 5-91
3C32 Tiff Resolution Error has been
detected in the received mail.
This mail could not be transferred
to the administrator.
P. 5-91
3C40 Tiff Paper Size Error has been
detected in the received mail.
TIFF paper size error P. 5-91
3C41 Tiff Paper Size Error has been
detected in the received mail.
This mail has been transferred to
the administrator.
P. 5-91
3C42 Tiff Paper Size Error has been
detected in the received mail.
This mail could not be transferred
to the administrator.
P. 5-91
3C50 Offramp Destination Error has
been detected in the received
mail.
Offramp destination error P. 5-91
3C51 Offramp Destination Error has
been detected in the received
mail. This mail has been trans-
ferred to the administrator.
P. 5-91
3C52 Offramp Destination Error has
been detected in the received
mail. This mail could not be trans-
ferred to the administrator.
P. 5-91
Error code
Message displayed in the
TopAccess screen
Contents Troubleshooting
June 2004 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO200L/202L/230/232/280/282
ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 19
2
3C60 Offramp Security Error has been
detected in the received mail.
Offramp security error P. 5-91
3C61 Offramp Security Error has been
detected in the received mail.
This mail has been transferred to
the administrator.
P. 5-91
3C62 Offramp Security Error has been
detected in the received mail.
This mail could not be transferred
to the administrator.
P. 5-91
3C70 Power Failure has been occurred
in E-mail receiving.
Power failure error P. 5-91
3D10 SMTP Destination Error has been
detected in the received mail.
This mail was deleted.
Destination address error P. 5-91
3D20 Offramp Destination limitation
Error has been detected in the
received mail.
Offramp destination limitation error P. 5-91
3D30 Fax Board Error has been
occurred in the received mail.
FAX board error P. 5-91
3E10 POP3 Connection Error has been
occurred in the received mail.
POP3 server connection error P. 5-92
3E20 POP3 Connection Timeout Error
has been occurred in the
received mail.
POP3 server connection time-out error P. 5-92
3E30 POP3 Login Error has been
occurred in the received mail.
POP3 login error P. 5-92
3E40 POP3 Login Error occurred in
received mail.
POP3 login method error P. 5-92
3F00 File I/O Error has been occurred
in this mail. The mail could not be
received until File I/O is recov-
ered.
File I/O error P. 5-92
3F10 P. 5-92
3F20 P. 5-92
3F30 P. 5-92
3F40 P. 5-92
Error code
Message displayed in the
TopAccess screen
Contents Troubleshooting
05/11
e-STUDIO200L/202L/230/232/280/282 June 2004 TOSHIBA TEC CORPORATION All rights reserved
ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 20
2.1.4 Printer function error
Following codes are displayed at the end of the user name on the print job log screen
(when GM-1020/3020, 1030/3030, 2020 or 2030 is installed (e-STUDIO200L/230/280))
(when GM-1070/4070, 1080U/4080U, 2070 or 2080U is installed (e-STUDIO202L/232/282))
Error code Contents Troubleshooting
4030 No printer kit / Invalid: When the printer kit or printer/scanner kit is not
installed, network print is performed after the trial period.
P. 5-92
4031 HDD full during print: Large quantity image data by private print or invalid
network print are saved in HDD.
P. 5-92
4032 Private-print-only error: Jobs other than Private print jobs cannot be per-
formed.
P. 5-92
4033 Printing data storing limitation error: Printing with its data being stored to the
HDD temporarily (Proof print, Private print, Scheduled print, etc.) cannot be
performed.
P. 5-92
4034 e-Filing storing limitation error: Printing with its data being stored to the HDD
(print and e-Filing, print to e-Filing, etc.) cannot be performed.
P. 5-92
4035 Local file storing limitation error: Network FAX or Internet FAX cannot be sent
when "Local" is selected for the destination of the file to save.
P. 5-92
4036 User authentication error: The user who intended to print a document is not
registered as a user.
P. 5-92
A221 Print job cancellation: Print job (copy, list print, network print) is deleted from
the print job screen.
P. 5-92
A222 Print job power failure: The power of the equipment is turned OFF during
print job (copy, list print, network print).
P. 5-92
A290 Limit over error: The numbers of output pages have exceeded those speci-
fied with both of the department code and the user code at the same time.
P. 5-93
A291 Limit over error: The number of output pages has exceeded the one speci-
fied with the user code.
P. 5-93
A292 Limit over error: The number of output pages has exceeded the one speci-
fied with the department code.
P. 5-93
05/11