Lime Plant Area 5 Maintenance and Shut-down Task Reversal Trap K662-1

Issued: 01.08.2001 Filename: SAMPLE WORK PACK Page: 1 of 24

Document Owner: Area Mgr Authorised: DocID: GPM-xxx-xxx



LIME PLANT AREA 5
MAINTENANCE AND
SHUT-DOWN TASK
WORK O/No.:
WORK PACK No.:
LKM10
and 11
STANDARD TASK
INSTRUCTION:
LKM10
and 11
ORIGINATOR: NICAS
SCOPE OF WORK: Remove and Overhaul Reversal Traps DATE: 01.08.08
EQUIPMENT DESCRIPTION: Reversal Trap and Stack
EQUIPMENT REGISTER No: K662-1
ITEM TASK DESCRIPTION DETAILS
TECHNICIAN
SIGNATURE
DATE
1. Obtain Permit to Work as per GPM 63.1 standard
tagout procedure.
Check and confirm Isolation(s).

2. Review Standard Task Instruction and sign.
(Ensure all personnel are aware of tasks and risks.)

3. Erect barricade below the proposed work and lift
areas to prevent personnel from entering.
Erect sign to advise of danger.

4. Remove guard from Reversal Trap.
5. Instrumentation/Electrical personnel to disconnect all
electrical connections to limit switches and electrical
components to facilitate repairs to Reversal Trap.

6. Disconnect and Cap all hydraulic lines, fittings etc.
7. Inspect all Hydraulic lines and fittings.
Replace as necessary.

8. Scaffold Personnel to erect scaffold as instructed by
the Area co-ordinator.

9. Remove Saddle from stack as shown in figure 3.0.
10. Position 90 tonne crane and the 140 tonne crane and
prepare for lift and Reversal Trap removal task.
90 tonne crane to be used with Mancage.
140 tonne crane to perform lifts.
Note: Use only authorised rigging personnel,
techniques and equipment.

Reversal Trap K662-1 Lime Plant Area 5 Maintenance and Shut-down Task
Page: 2 of 24 Filename: SAMPLE WORK PACK Issued: 01.08.2001
DocID: GPM-xxx-xxx Authorised: Document Owner: Area Mgr


ITEM TASK DESCRIPTION DETAILS
TECHNICIAN
SIGNATURE
DATE
11. Remove stack Flange Mounting Bolts.
12. Remove Stack and lower to ground.
13. Support Combustion Air Ducting as shown in Figure
3.0.
Note: Use only authorised rigging personnel,
techniques and equipment.

14. Unbolt and remove Combustion Air Ducting section
and lower to the top of SL662-3, 900 tonne burnt lime
storage silo.

15. Ensure duct is safe, secure and not fouling walkway.
16. Support Trouser Leg as shown in Figure 4.0 using
chain block and slings.

17. Unbolt Lower Flange at trouser leg.
18. Unbolt Lower Flange of reversal trap.
19. Remove Reversal Trap and lower to ground.
Note: Insert a 17mm thick Marine Ply section over
the opening left by the removal of the Reversal Trap.
Note: Use only authorised rigging personnel,
techniques and equipment.

20. Arrange truck and rigging crew to collect Reversal
Trap and transport to workshop for inspection and
repair.

21. NDT personnel to carry out inspections to the
Reversal Trap and advise of required welding repairs
and procedures.
All welding repairs to be undertaken in site
fabrication shop.

22. At the completion of welding repairs, the Reversal
Trap is to be transported to the Machine Shop.

23. Planned Maintenance to inspect reversal and closing
trap Shaft Bearings.
Replace as necessary.

24. Inspect and replace reversal and closing Trap Seals.
Lime Plant Area 5 Maintenance and Shut-down Task Reversal Trap K662-1
Issued: 01.08.2001 Filename: SAMPLE WORK PACK Page: 3 of 24
Document Owner: Area Mgr Authorised: DocID: GPM-xxx-xxx


ITEM TASK DESCRIPTION DETAILS
TECHNICIAN
SIGNATURE
DATE
25. Inspect, repair, and replace as necessary, reversal and
closing trap Sealing Plate and Pivot Arm.

26. Inspect reversal and closing trap counterweight for
wear or damage.
Repair or replace as necessary.

27. Inspect Access Door Hinges for wear or damage.
Repair or replace hinges as necessary.

28. Pressure Test Reversal Trap in workshop.
29. Test correct operation and function of reversal trap.
30. Inspect Reversal Trap Stack Refractory for damage or
wear.
Note: The inspections and repairs should be carried
out by suitably qualified Refractory Personnel

31. Inspect the Inverted Witches Hat for corrosion and
wear.
Repair Inverted Witches Hat as necessary.

32. Install Inspection Port in each of the Reversal Trap
Stacks. (Modification)
Details of modification to be provided by the Area
Engineer.

33. Prepare and clean all parts, gasket surfaces, nuts and
bolts etc for the installment of Reversal Traps to the
Kiln.

34. HOLD POINT. Area Co-ordinator to confirm and
authorise timing of reinstatement of Reversal Trap.

35. Position 90 tonne crane and the 140 tonne crane.
Prepare for lift and reinstatement of Reversal Trap.
90 tonne crane to be used with Mancage.
140 tonne crane to perform lifts.
Note: Use only authorised rigging personnel,
techniques and equipment.


Reversal Trap K662-1 Lime Plant Area 5 Maintenance and Shut-down Task
Page: 4 of 24 Filename: SAMPLE WORK PACK Issued: 01.08.2001
DocID: GPM-xxx-xxx Authorised: Document Owner: Area Mgr


ITEM TASK DESCRIPTION DETAILS
TECHNICIAN
SIGNATURE
DATE
36. Raise Reversal Trap to correct level on Kiln.
Note: Use only authorised rigging personnel,
techniques and equipment.

37. Rig and install Reversal Trap into correct position.
38. Install bolts to lower flange of Reversal Trap and
tension. (Insert correct bolt tension here)

39. Install bolts to lower flange at Trouser Leg and
tension. (Insert correct bolt tension here)

40. Remove chain block and sling support from Trouser
Leg as shown in Figure 4.0.

41. Raise and affix Combustion Air Ducting section in
correct position. Fit flange bolts and tighten.
90 tonne crane to be used with Mancage.
140 tonne crane to perform lifts.
Note: Use only authorised rigging personnel,
techniques and equipment.

42. Reinstate Stack to reversal trap.
Note: Use only Authorised rigging personnel,
techniques and equipment.

43. Reinstate Stack Flange mounting bolts and tension.
(Insert correct bolt tension here)

44. Inspect and repair/replace as necessary lubrication
lines, purge lubrication points.
Replace automatic lubricator pods as necessary.

45. Replace hydraulic cylinder with new or reconditioned
unit.

46. Refit hydraulic hoses to hydraulic cylinder.
47. Scaffold Personnel to remove scaffold as instructed
by the Area Co-ordinator.

48. Instrumentation/Electrical personnel to re-connect all
electrical connections and test/check correct function
of limit switches.

49. Reinstate guard to reversal trap.
Lime Plant Area 5 Maintenance and Shut-down Task Reversal Trap K662-1
Issued: 01.08.2001 Filename: SAMPLE WORK PACK Page: 5 of 24
Document Owner: Area Mgr Authorised: DocID: GPM-xxx-xxx


ITEM TASK DESCRIPTION DETAILS
TECHNICIAN
SIGNATURE
DATE
50. All areas worked in to be left clean and safe.
51. Remove Personal Danger Tag and sign off Standard
Clearance Certificate.

RECORD TOTAL HOURS TAKEN TO COMPLETE TASK. _____________ HOURS



POSITION JOB TECHNICIAN JOB SUPERVISOR CO-ORDINATOR
Print Name:
Signature:
Date:













IN EVENT OF EMERGENCY
PHONE OR
RADIO CHANNEL
222
1
Reversal Trap K662-1 Lime Plant Area 5 Maintenance and Shut-down Task
Page: 6 of 24 Filename: SAMPLE WORK PACK Issued: 01.08.2001
DocID: GPM-xxx-xxx Authorised: Document Owner: Area Mgr


Fitters Comments:











Name:

Supervisors Comments:











Name:

Lime Plant Area 5 Maintenance and Shut-down Task Reversal Trap K662-1
Issued: 01.08.2001 Filename: SAMPLE WORK PACK Page: 7 of 24
Document Owner: Area Mgr Authorised: DocID: GPM-xxx-xxx


Reversal Trap K662-1
There are two reversal traps, one located on either side of the Lime Kiln as shown in
Figure 1.0 below.


Figure 1.0: Showing the location of the Reversal Traps


Caution
Erect barricade below the proposed work and lift areas
Erect sign to advise of Danger.
Reversal Trap K662-1 Lime Plant Area 5 Maintenance and Shut-down Task
Page: 8 of 24 Filename: SAMPLE WORK PACK Issued: 01.08.2001
DocID: GPM-xxx-xxx Authorised: Document Owner: Area Mgr



Remove the guard from the Reversal Trap.
Instrumentation/Electrical personnel to disconnect all limit switches and electrical
connections to facilitate removal of the Reversal Trap.
Disconnect and cap all hydraulic lines and fittings.


Figure 2.0: Showing the Reversal Trap Guard, Hydraulic Cylinder
and Electrical Equipment

Lime Plant Area 5 Maintenance and Shut-down Task Reversal Trap K662-1
Issued: 01.08.2001 Filename: SAMPLE WORK PACK Page: 9 of 24
Document Owner: Area Mgr Authorised: DocID: GPM-xxx-xxx


Remove the saddle from the stack as shown in Figure 3.0 below.
Position the 90 tonne crane and the 140 tonne crane to prepare for lift and task.


Figure 3.0: Showing the Reversal Trap, Trap Stack and
Combustion Air Ducting
Reversal Trap K662-1 Lime Plant Area 5 Maintenance and Shut-down Task
Page: 10 of 24 Filename: SAMPLE WORK PACK Issued: 01.08.2001
DocID: GPM-xxx-xxx Authorised: Document Owner: Area Mgr



Support the Trouser Leg as shown in Figure 4.0 below using chain block and slings.
Unbolt the lower flange at the trouser leg.


Figure 4.0: Showing Reversal Trap and Trouser Leg

Lime Plant Area 5 Maintenance and Shut-down Task Reversal Trap K662-1
Issued: 01.08.2001 Filename: SAMPLE WORK PACK Page: 11 of 24
Document Owner: Area Mgr Authorised: DocID: GPM-xxx-xxx


Unbolt lower flange mounting bolts of reversal trap as shown below in Figure 5.0.
Rig and prepare to remove the Reversal Trap.
Remove the trap using the 140 tonne crane and lower to the ground.


Figure 5.0: Showing Reversal Trap Lower Mounting Support Bolts



Caution
Insert a 17mm thick Marine Plywood section over the opening
left by the removal of the Reversal Trap.
Secure the plywood to prevent falling or the possibility of it
being blown away and to prevent personnel, tools or other
items falling into the opening.

Reversal Trap K662-1 Lime Plant Area 5 Maintenance and Shut-down Task
Page: 12 of 24 Filename: SAMPLE WORK PACK Issued: 01.08.2001
DocID: GPM-xxx-xxx Authorised: Document Owner: Area Mgr




Lime Plant Area 5 Maintenance and Shut-down Task Reversal Trap K662-1
Issued: 01.08.2001 Filename: SAMPLE WORK PACK Page: 13 of 24
Document Owner: Area Mgr Authorised: DocID: GPM-xxx-xxx


STANDARD TASK INSTRUCTION

STI NUMBER: STI-LKM10 TASK: Remove and Overhaul Reversal Trap and Stack CRITICAL TASK? (YES/NO)
WORK GROUP: Production Maintenance PREPARED BY: REVISON NUMBER: Initial Issue
AREA: Lime Plant 662 DATE: 01.08.2001 REVISION DATE:
This STI shall be reviewed for correctness and understanding prior to commencement of this particular task and after each Revision.
At these times, all members of the STI team shall sign off over the page.
All new starters on this task shall review this STI with the Supervisor and sign off over the page.
All revisions to this STI must be agreed to by all members of the STI team and recorded on this STI form with the Revision number date upgraded.
SAFETY GEAR, TOOLS, EQUIPMENT, INSTRUCTIONS, PRE-REQUISITES AND COMPETENCIES SPECIFIC TO THIS TASK.
Work Permit Requirements Personal Protective Equipment (PPE) Requirements
Confined Space Vessel Entry Excavation Hot Work Face Shield Monogoggles Hearing Protection
Electrical Isolation High Voltage Scaffolding Radiation Respirator Dust Masks Gloves
Personnel Cage Safe Work Gas Test Isolation Safety Helmet Safety Harness Sun Protection
Commissioning Life Vest Standard PPE
Job Specific Resources Competencies Required Equip./Machinery Required (List)
Barricading Signs Sentry & Sentry Board Operator Elect/Instrt Fitter 140 and 90 tonne Cranes with Mancage Facility
Fire Blankets Extinguishers
Two-way Radio/
Mobile Phone
Boilermaker
Crane Driver
Rigger

Rigging Equipment, Slings, Shackles, Chain
blocks
Running Water Life Ring Voltage Reducer USM Refractory Personnel

Fitter Mechanic


Reversal Trap K662-1 Lime Plant Area 5 Maintenance and Shut-down Task
Page: 14 of 24 Filename: SAMPLE WORK PACK Issued: 01.08.2001
DocID: GPM-xxx-xxx Authorised: Document Owner: Area Mgr


No. SPECIFIC JOB STEPS HAZARDS
CTA SCORING
HAZARD CONTROLS
S EX P TOTAL
1.
Obtain Permit to Work as per GPM 63.1
standard tagout procedure.
Check and confirm Isolation(s).

Working on incorrect
equipment.

Check and confirm
isolation(s), correct equipment.
2.
Review Standard Task Instruction and
sign. (Ensure all personnel are aware of
tasks and risks.)

Unaware of safety and task
requirements.

Understand safety and task
requirements.
3.
Erect barricade below the proposed work
and lift areas to prevent personnel from
entering. Erect sign to advise of danger.
Sprain, strains. Use correct lifting techniques.
4.
Remove guard from Reversal Trap.
Cuts and abrasions. Correct area PPE, wear gloves.
5.
Instrumentation/Electrical personnel to
disconnect all electrical connections to
limit switches and electrical components to
facilitate removal of Reversal Traps.
Electrocution.
Ensure correct isolation before
commencement of task.
Test circuits to ensure isolation
6.
Disconnect and cap all hydraulic lines,
fittings etc.

Oil spill
Slip, fall.

Clean and contain oil spillage
immediately.
7.
Inspect all hydraulic lines and fittings.
Replace as necessary.

Oil spill
Slip, fall.

Clean and contain oil spillage
immediately.
Lime Plant Area 5 Maintenance and Shut-down Task Reversal Trap K662-1
Issued: 01.08.2001 Filename: SAMPLE WORK PACK Page: 15 of 24
Document Owner: Area Mgr Authorised: DocID: GPM-xxx-xxx


8.
Scaffold personnel to erect scaffold as
instructed from the Area co-ordinator.

Working at heights
Sprain, strains.

Ensure area below is
barricaded.
Ensure no personnel enter
barricaded area.
Use correct lifting techniques.
9.
Remove saddle from stack as shown in
Figure 3.0.
Working at heights
Ensure area below is
barricaded.
Ensure no personnel enter
barricaded area.
10.
Position 90 tonne crane and the 140 tonne
crane to prepare for lift and Reversal Trap
removal task.
Sprain, strains
90 tonne crane to be used with
Mancage. 140 tonne crane to
perform lifts.
Use only authorised rigging
personnel, techniques and
equipment
11.
Remove stack flange mounting bolts.

Working at heights
Falling objects.

Ensure area below is
barricaded.
Ensure no personnel enter
crane working radius or
barricaded area.
Reversal Trap K662-1 Lime Plant Area 5 Maintenance and Shut-down Task
Page: 16 of 24 Filename: SAMPLE WORK PACK Issued: 01.08.2001
DocID: GPM-xxx-xxx Authorised: Document Owner: Area Mgr


12.
Remove stack and lower to ground using
140 tonne crane.

Working at heights
Falling objects.

Ensure area below is
barricaded.
Ensure no personnel enter
crane working radius or
barricaded area.
Use only authorised rigging
personnel, techniques and
equipment.
13.
Support combustion air ducting as shown
in Figure 3.0.
Note: Use only authorised rigging
personnel, techniques and equipment.
Sprain, strains Use correct lifting techniques.
14.
Unbolt and remove combustion air ducting
section and lower to the top of SL662-3,
900 tonne burnt lime storage silo.

Working at heights
Falling objects.

Ensure area below is
barricaded.
Ensure no personnel enter
crane working radius or
barricaded area.
Use only authorised rigging
personnel, techniques and
equipment.
15.
Ensure duct is safe, secure and not fouling
walkway.

Sprain, strains
Trip, fall.

Use correct lifting techniques.
Good housekeeping.
Lime Plant Area 5 Maintenance and Shut-down Task Reversal Trap K662-1
Issued: 01.08.2001 Filename: SAMPLE WORK PACK Page: 17 of 24
Document Owner: Area Mgr Authorised: DocID: GPM-xxx-xxx


16.
Support trouser leg as shown in Figure 4.0
using chain block and slings.
Sprain, strains.
Use only authorised rigging
personnel, techniques and
equipment.
17.
Unbolt lower flange at trouser leg.
Sprain, strains. Use correct lifting techniques.
18.
Unbolt lower flange of reversal trap.
Sprain, strains. Use correct lifting techniques.
19.
Remove Reversal trap and lower to
ground.
Note: Insert a 17mm thick Marine Ply
section over the opening left by the
removal of the Reversal Trap.

Working at heights
Falling objects.

Ensure area below is
barricaded.
Ensure no personnel enter
crane working radius or
barricaded area.
Use only authorised rigging
personnel, techniques and
equipment.
20.
Arrange truck and rigging crew to collect
Reversal Trap and transport to workshop
for inspection and repair.
Sprain, strains.
Use only authorised rigging
personnel, techniques and
equipment.
21.
NDT personnel to carry out inspections to
the Reversal Trap and advise of required
welding repairs and procedures.
All welding repairs to be undertaken in site
fabrication shop.

Cuts and abrasions
Noise from grinder
Welding flashes to eyes.

Wear gloves.
Wear hearing protection.
Erect weld barricade if
required.
22.
At the completion of welding repairs, the
Reversal Trap is to be transported to the
Machine Shop.
Sprain, strains. Use correct lifting techniques.
Reversal Trap K662-1 Lime Plant Area 5 Maintenance and Shut-down Task
Page: 18 of 24 Filename: SAMPLE WORK PACK Issued: 01.08.2001
DocID: GPM-xxx-xxx Authorised: Document Owner: Area Mgr


23.
Planned Maintenance to inspect reversal
and closing trap Shaft Bearings.
Replace as necessary.
Cuts and abrasions. Correct area PPE, wear gloves.
24.
Inspect and replace reversal and closing
Trap Seals.
Cuts and abrasions. Correct area PPE, wear gloves.
25.
Inspect, repair, and replace as necessary,
reversal and closing trap sealing plate and
pivot arm.
Cuts and abrasions. Correct area PPE, wear gloves.
26.
Inspect reversal and closing trap
Counterweight for wear or damage.
Repair or replace as necessary.
Cuts and abrasions. Correct area PPE, wear gloves.
27.
Inspect access door hinges for wear or
damage.
Repair or replace hinges as necessary.
Cuts and abrasions. Correct area PPE, wear gloves.
28.
Pressure test Reversal Trap in workshop.
Cuts and abrasions. Correct area PPE, wear gloves.
29.
Test correct operation and function of
reversal trap.
Cuts and abrasions. Correct area PPE, wear gloves.
30.
Inspect Reversal Trap Stack Refractory for
damage or wear.
Cuts and abrasions. Correct area PPE, wear gloves.
31.
Inspect the inverted witches hat for
corrosion and wear.
Repair inverted witches hat as necessary.
Cuts and abrasions. Correct area PPE, wear gloves.
Lime Plant Area 5 Maintenance and Shut-down Task Reversal Trap K662-1
Issued: 01.08.2001 Filename: SAMPLE WORK PACK Page: 19 of 24
Document Owner: Area Mgr Authorised: DocID: GPM-xxx-xxx


32.
Install inspection port in each of the
Reversal Trap Stacks. (Modification)
Details of modification to be provided by
the Area Engineer.
Cuts and abrasions. Correct area PPE, wear gloves.
33.
Prepare and clean all parts, gasket
surfaces, nuts and bolts etc for the
installment of Reversal Traps to the Kiln.
Cuts and abrasions. Correct area PPE, wear gloves.
34.
HOLD POINT Area Co-ordinator to
confirm and authorise timing of
reinstatement of Reversal Trap.

35.
Position 90 tonne crane and the 140 tonne
crane and prepare for lift and reinstatement
of Reversal Trap.
Sprain, strains
Ensure area below is
barricaded.
Ensure no personnel enter
crane working radius or
barricaded area.
Use only authorised rigging
personnel, techniques and
equipment.
36.
Raise Reversal Trap to correct level on
Kiln.


Working at heights
Falling objects.

Ensure area below is
barricaded.
Ensure no personnel enter
crane working radius or
barricaded area.
Use only authorised rigging
personnel, techniques and
equipment.
Reversal Trap K662-1 Lime Plant Area 5 Maintenance and Shut-down Task
Page: 20 of 24 Filename: SAMPLE WORK PACK Issued: 01.08.2001
DocID: GPM-xxx-xxx Authorised: Document Owner: Area Mgr


37.
Rig and install Reversal Trap into correct
position.
Sprain, strains
Use only authorised rigging
personnel, techniques and
equipment.
38.
Install bolts to lower flange of reversal trap
and tension. (Insert correct tension)
Cuts and abrasions Correct area PPE, wear gloves.
39.
Install bolts to lower flange at trouser leg
and tension. (Insert correct tension)
Cuts and abrasions Correct area PPE, wear gloves.
40.
Remove chain block and sling support
from trouser leg as shown in Figure 4.0.
Sprain, strains
Use only authorised rigging
personnel, techniques and
equipment.
41.
Raise and affix combustion air ducting
section in correct position. Fit flange bolts
and tighten.
Note: 90 tonne crane to be used with
Mancage. 140 tonne crane to perform
lifts.

Working at heights
Falling objects.

Ensure area below is
barricaded.
Ensure no personnel enter
crane working radius or
barricaded area.
Use only authorised rigging
personnel, techniques and
equipment.
42.
Reinstate stack to Reversal Trap.

Working at heights
Falling objects.

Ensure area below is
barricaded.
Ensure no personnel enter
crane working radius or
barricaded area.
Use only authorised rigging
personnel, techniques and
equipment.
Lime Plant Area 5 Maintenance and Shut-down Task Reversal Trap K662-1
Issued: 01.08.2001 Filename: SAMPLE WORK PACK Page: 21 of 24
Document Owner: Area Mgr Authorised: DocID: GPM-xxx-xxx


43.
Reinstate stack flange mounting bolts and
tension. (Insert correct tension)

Working at heights
Falling objects.

Ensure area below is
barricaded.
Ensure no personnel enter
crane working radius or
barricaded area.
Use only authorised rigging
personnel, techniques and
equipment.
44.
Inspect and repair/replace as necessary
lubrication lines, purge lubrication points.
Replace automatic lubricator pods as
necessary.

Sprain, strains
Cuts and abrasions.

Use correct lifting techniques.
Correct area PPE, wear gloves
45.
Replace hydraulic cylinder with new or
reconditioned unit.
Sprain, strains.
Use correct lifting techniques.
Correct area PPE, wear gloves.
46.
Refit hydraulic hoses to hydraulic cylinder.
Sprain, strains.
Use correct lifting techniques.
Correct area PPE, wear gloves.
47.
Scaffold Personnel to remove scaffold as
instructed by the Area co-ordinator.

Working at heights
Sprain, strains.

Ensure area below is
barricaded.
Ensure no personnel enter
barricaded area.
Use correct lifting techniques.
48.
Instrumentation/Electrical personnel to
re-connect all electrical connections and
test/check correct function of limit
switches.
Electrocution. Authorised personnel only.
Reversal Trap K662-1 Lime Plant Area 5 Maintenance and Shut-down Task
Page: 22 of 24 Filename: SAMPLE WORK PACK Issued: 01.08.2001
DocID: GPM-xxx-xxx Authorised: Document Owner: Area Mgr


49.
Reinstate guard to reversal trap.
Cuts and abrasions.
Use correct lifting techniques.
Correct area PPE, wear gloves.
50.
All areas worked in to be left clean and
safe.
Trip, fall Good housekeeping.
51.
Remove Personal Danger Tag and sign off
Standard Clearance Certificate.

SCORING: S = Severity EX = Exposure P = Probability.
Task steps are measured on a scale of 10 for Severity, Exposure and Probability.
Critical steps are level 7 or higher. They are denoted by a red criticality rating within a red hexagon and the critical step is surrounded by double red
thick and thin lines.

Lime Plant Area 5 Maintenance and Shut-down Task Reversal Trap K662-1
Issued: 01.08.2001 Filename: SAMPLE WORK PACK Page: 23 of 24
Document Owner: Area Mgr Authorised: DocID: GPM-xxx-xxx



I HAVE REVIEWED THIS STANDARD TASK INSTRUCTION
This STI shall be reviewed for correctness and understanding prior to commencement of this particular task. All members of this task MUST SIGN in the presence of the Job Supervisor.
I confirm that I have read and understand the Tasks, Risks and Hazards associated with this Maintenance Task.
NAME DATE NAME DATE NAME DATE


















Reversal Trap K662-1 Lime Plant Area 5 Maintenance and Shut-down Task
Page: 24 of 24 Filename: SAMPLE WORK PACK Issued: 01.08.2001
DocID: GPM-xxx-xxx Authorised: Document Owner: Area Mgr



Table 1.0: APL Listing for Reversal Trap K662-1