Scribd
Upload
2K views4 pages

API Datasheet Heat Exchanger

This document contains specifications for a heat exchanger unit including: - Performance details like fluid quantities, temperatures, pressures, heat transfer rates. - Construction details for the shells, tubes, tube layout and materials of construction. - Design codes, pressures, temperatures and load conditions. - Connection schedules and optional mechanical/thermal data.

Uploaded by

Soraya Zahra
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLSX, PDF, TXT or read online on Scribd
2K views4 pages

API Datasheet Heat Exchanger

This document contains specifications for a heat exchanger unit including: - Performance details like fluid quantities, temperatures, pressures, heat transfer rates. - Construction details for the shells, tubes, tube layout and materials of construction. - Design codes, pressures, temperatures and load conditions. - Connection schedules and optional mechanical/thermal data.

Uploaded by

Soraya Zahra
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLSX, PDF, TXT or read online on Scribd
You are on page 1/ 4

Client : PT VICO Indonesia Location Page 1 of 5

Process Unit : Item No. Document No.


Job No. : Fabricator
Service of unit : No. of units :
Size : TEMA Type Connected in Parallel Series
Effective surface per unit ft
2
shells/unit Surface/shell (eff.)
PERFORMANCE OF ONE UNIT
Inlet Inlet Outlet
Fluid Name
Fluid quantity, total lb/h
Vapour (relative molecular mass) lb/h
Liquid lb/h
Steam lb/h
Water lb/h
Noncondensable/ relative molecular mass lb/h
Temperature F
Density (vapour/liquid) lb/ft
3
Viscosity cP
Specific heat (vapour/liquid) Btu/(lb-F)
Thermal conductivity (vapour/liquid) Btu/(h-ft-F)
Specific latent heat Btu/lb @ F
Inlet pressure psig
Velocity ft/s
Pressure drop (alowable/calculated) psig
Fouling resistance h-ft
2
-F/Btu
Average ifilm coefficient Btu/(h-ft-F)
Heat Exchanged Btu/h
Heat transfer rate (required/fouled/clean) Btu/(h-ft-F)
V
2
[lb/ft.s
2
]: Inlet Nozzle Bundle entrance Bundle exit
CONSTRUCTION PER SHELL
Tube No. OD in
Thickness
Pitch Inlet
Length Outlet
Tube-tubesheet joint Intermediate
Shell diameter (ID/OD) / in Vent
Cross-baffle type Drain
Spacing : c/c in No. of crosspasses Pressure relief
% Cut Design pressure psig
Tube support type Vacuum pressure psia
Long baffle seal type Design temp. (Max/MDMT) F
Bypass seal type No.of passes per shell
Impingement protection (Y/N) Corrosion allowance in
MATERIAL OF CONSTRUCTION
Shell Tubes Gaskets :
Shell cover Shell side
Channel or bonnet Tube side
Channel cover Floating head
Floating head cover/bolts Spare sets req'd
Tubesheet Stat. Floating Test ring req'd (Y/N)
Baffles : Cross. Long Insullation : shell
Tube support material Channel inlet/exit
Expansion joint type Expansion joint material
Pressure design code Stamp Calc. MAWP (Y/N) TEMA Class
REMARKS :
Originator/ Check : / Approved Issue Date : Issue No.

NOZZLES - No., Size and Rating

SHELL SIDE TUBE SIDE

Mean temp. diff., MTD (corrected) (weighted)


TUBE SIDE

//

/

/


Outlet

@



SHELL SIDE

Job No. Page 2 of 5


Client
Location
Item No.
Document No. Issue No.
Shell Tubesheet Tube
Design
Normal
Starting
Shutdown
Upset #1
Upset #2
Steam out
Expansion joint esign life cycles
Shell : in
Head : in
Pipe/stub ends : in
Nozzle necks : in
Nozzle flanges : in
Body flanges : in
Expansion joint : in
Support in
Bolting (internal) : in
Bolting (eksternal) : in
Nozzle reinforcement : in
Tubes : in
Tubesheets : in
Bonnet/channel : in
Bonnet head (s) in
Channel cover (s) in
Body flanges : in
Pipe/stub ends : in
Bolting (internal) : in
Bolting (eksternal) : in
Nozzle reinforcement : in
Nozzle necks : in
Nozzle flanges : in
Baffles, spacers, tie rods : in
Shell side : Thickness : in MAWP (hot and corroded) : psi
= psi m = MAP (new and cold) : psi
Tube side : Thickness : in Hydrotest pressure :
= psi m = Field : psig Shop : psig
Floating head Thickness : in Masses : Empty : lb Bundle : lb
= psi m = Full of water lb
GASKETS (Optional) MECHANICAL DATA (Optional)

THERMAL EXPANSION DESIGN INFORMATION (Optional)


MATERIALS OF CONSTRUCTION (Optional) Corr. allow.
Tube
press. Psig
CONNECTION SCHEDULE (Optional)
mean metal
temp. F
Shell
press.
Psig
mean metal
temp. F
mean metal
temp. F
No.
req'd
Mark Size Rating Facing Description
Job No. Page 3 of 5
Client
Location
Item No.
Document No. Issue No.
ADDITIONAL REMARKS, SKETCHES, ETC. (Optional)
Job No. Page 4 of 5
Client
Location
Item No.
Document No. Issue No.
Fluid Name .. Ref. Pressure 1 : psi (abs)
Temp.
F
Thermal Sp. Heat
Cond. Vap Vapour
Btu/(h-ft-F) Btu/(lb-F)
Pressure
psi (abs)
Enthalpy
Btu/lb
Density
Vapour
lb/ft3
Viscosity
Vapour
cP

You might also like