1

Double Sideband (DSB) and Amplitude Modulation (AM)

Modules: Audio Oscillator, Wideband True RMS Meter, Multiplier, Adder, Utilities, Phase
Shifter, Tuneable LPFs (2), Quadrature Utilities, Twin Pulse Generator, Digital Utilities, Speech,
Headphones
0 Pre-Laboratory Reading
Double sideband (DSB) is one of the easiest modulation techniques to understand, so it is a good
starting point for the study of modulation. A type of DSB, called binary phase-shift keying, is
used for digital telemetry. Amplitude modulation (AM) is similar to DSB but has the advantage
of permitting a simpler demodulator, the envelope detector. AM is used for broadcast radio,
aviation radio, citizens band (CB) radio, and short-wave broadcasting.
0.1 Double Sideband (DSB) Modulation
A message signal can be DSB modulated onto a carrier with a simple multiplication. The
modulated carrier can be represented by

(1)
where

is the carrier frequency. The Fourier transform of the modulator output is related
to the Fourier transform of the message signal by

(2)
For a real , || is symmetric about and |

| is symmetric about

.
For the present discussion, it is only necessary to consider that part of that lies in the
positive half of the frequency axis. The signal content that lies in the frequency domain below

is the lower sideband. The signal content that lies in the frequency domain above

is the upper
sideband. This is the origin of the term double sideband.
When studying and testing analog modulation schemes, it is convenient to use a sinusoid as the
message signal. This is a good choice for several reasons. First, when testing a system in the
laboratory, it is desirable to use a periodic signal since a stable oscilloscope display with
continuous signal capture is then possible. Second, the mathematics are usually simpler with a
sinusoidal message signal. Third, a sinusoid is easy to generate in the laboratory. After a
communication system goes into the field and becomes operational, the message signal would
not ordinarily be sinusoidal, of course.

2

If is a sinusoid of frequency

, the modulated carrier can be written as

]
(3)
This last expression indicates that when a carrier is DSB modulated by a message sinusoid, the
modulated carrier is equivalent to the sum of two sinusoids: one having the difference frequency

and the other with the sum frequency

. In the frequency domain there is signal

content lying on both sides of the carrier frequency. When is a sinusoid, each sideband is
one discrete spectral line (on the positive half of the frequency axis).
In the general case where is real but not a sinusoid, each sideband is more complicated than
a single discrete spectral line. However, it is still true that there are two sidebands: a lower and
an upper.
In the time domain, a carrier that is DSB modulated by a message sinusoid looks like this:

DSB modulated carrier (solid curve) and message sinusoid (dashed curve)

A DSB modulated carrier is normally demodulated with a synchronous detector. This means
that the modulated carrier is multiplied by a local oscillator and the product is then sent to a low-
pass filter. With synchronous detection the frequency and phase of the local oscillator are
important. Its frequency must match that of the carrier. The local oscillator phase must
approximately match that of the carrier.
When the modulated carrier of Eq. (1) is sent to a synchronous detector, the demodulator
(detector) output can be written as
3

{

}

{

}


{

}
(4)
The local oscillator is modeled as

. It has a frequency that matches that of the

carrier. However, allowance is made for a phase that might not match that of the carrier. The
low-pass filtering is represented by {}.

DSB modulator (left) and synchronous detector as demodulator (right)

The message signal is presumably low pass. The term

represents a
bandpass signal centered at

in the frequency domain. The bandwidth of the low-pass filter

should be large enough that passes through the filter with little distortion. If the bandwidth
of is small compared with

(as it will be in this experiment and as it normally is in

practice), then a bandwidth for the low-pass filter can easily be selected that passes but
blocks

. The demodulator output is, in this case,

(5)
where

is the lowpass gain of the filter. There will also be a time delay in going through the
filter; this is not indicated in Eq. (5) because it is not important for the present discussion. The
filter output is a scaled and delayed version of . A demodulation that produces a scaled and
delayed version of the original message is considered successful.
An important consideration is the phase difference between the local oscillator and the carrier.
The amplitude of the demodulator output is a function of . If

, is zero. It is
essential that remain close to

so that the message not suffer fading at the output of the

demodulator. Keeping close to

is normally accomplished within the receiver by a circuit

that performs carrier synchronization.

PF x x LPF
message
carrier
modulator
synchronous detector
local
oscillator
4

0.2 Amplitude Modulation (AM)
If a DC component is added to the message signal before multiplication with a carrier, then
the modulation scheme is known as amplitude modulation (AM). The purpose of the DC
component is to permit the modulated carrier to be demodulated at the receiver by a means other
than synchronous detection. More will be said about this later.

Modulator for AM

The output of the modulator can be written:
[

Where

and

are constants.
For AM the maximum of the absolute value of the message signal is of importance; this is
denoted here by ( ).
||
(6)
It is useful to define a normalized message signal

as follows:

(7)
The maximum of the absolute value of

is therefore
|

|
(8)
This is what is meant by normalization. The modulator output can be rewritten as
[

Factoring

out of the bracket and defining

(9)
as the modulation index for AM, the modulator output can then be written
x
message
carrier
+
DC
5

The modulation index of Eq. (9) is always non-negative (that is, positive or 0) since is positive
(by definition) and the constants

and

should always have the same sign.

The term

is a residual carrier and the term

is a DSB-
modulated carrier. The ratio of the peak value of the DSB term to the peak value of the residual
carrier is
|

|
In the above, we recognize that is positive. The ratio of the peak value of the DSB term to the
peak value of the residual carrier is the modulation index.
There are some AM calculations that involve the ratio of the DSB term to the residual carrier.
For this class of problem, it is acceptable to forget about the common factor

. The important
problem of selecting an appropriate value for the modulation index is an example of this class
of problem. Therefore, in the analysis that appears below, we sometimes forget about

and use
the following definition:
[

(10)
There are, of course, problems for which the constant

must be considered. One problem of

this type is when we must determine if any stage in the transmitter is overloaded (the voltage is
so large that the stage is unintentionally operated in a nonlinear regime).
As was done with DSB, the next step in this description of AM is to consider a sinusoidal
message signal.

(11)
Eq. (11) satisfies Eq. (8). Three cases are of interest:
100% modulation
undermodulation
overmodulation
The time-domain view of the modulated carrier is shown below for these three cases. It helps
when interpreting these figures to consider the quantity

. This quantity has a

minimum value of 0 for . The minimum value is positive and non-zero for . The
minimum value is negative for . (It is assumed here that and therefore that

.)
6


(100% modulation): AM carrier (solid curve) and message sinusoid (dashed curve)


(undermodulation): AM carrier (solid curve) and message sinusoid (dashed curve)


(overmodulation): AM carrier (solid curve) and message sinusoid (dashed curve)
7

In the laboratory, the modulation index can be set with good accuracy when the message signal
is a sinusoid. The rms value of

and the rms value of

are separately measured. For

the

of Eq. (11), these rms values are |

| and |

|, respectively. The ratio of these

two rms values is:

(sinusoid)
(12)
A desired modulation index can be set by adjusting the gain on the (sinusoidal) message signal
until the ratio equals . It must be emphasized that Eq. (12) is valid only for a sinusoidal
message signal.
There is a technique for estimating the modulation index of an AM carrier that is quite general; it
does not require the message signal to be a sinusoid. This technique uses the XY view of an
oscilloscope. The multiplier input that is not the carrier is applied to Channel A. In the case of
DSB, this is . In the case of AM, this is

. To Channel B is applied the output of

the multiplier (that is, the modulated carrier). When this is done, one of the following figures is
displayed:


DSB AM: AM: AM:
100% modulation undermodulation overmodulation

Consider first the DSB figure. The modulated carrier

is plotted against . At
any instant when the message signal is 0, the modulated carrier is also zero. The center of the
bowtie represents this point; it is the origin. When takes on the value

, the modulated
carrier can take on any value between |

| and |

|. The larger |

|, the wider the range of

values that the modulated carrier can assume.
For AM, the modulated carrier [

is plotted against

. If ,
then

takes on only non-negative values, so only the right half of the bowtie is
present. If , then the minimum value of

is a positive and non-zero value. If

, then the minimum value of

is negative.
The nice thing about using the XY view to estimate the modulation index is that this works for
any message signal, even an audio signal (from a microphone, for example). The problem of
calculating the modulation index for a general audio signal is that it can be difficult even to
8

identify and therefore

for a signal that appears random. The XY view provides a quick

but approximate characterization of the AM.
It is worthwhile to consider how an AM carrier looks in the frequency domain. This is done here
for the case of a sinusoidal message signal. Eqs. (10) and (11) together can be rewritten as

]
(13)
It is clear from Eq. (13) that the spectrum of an AM carrier with sinusoidal message signal
contains three discrete spectral lines (on the positive half of the frequency axis). The frequencies
are:

, and

. This is similar to the case of DSB, except for the additional

discrete spectral line at

, which is known as a residual carrier. Each of the sideband lines has a

line height that is different from that of the residual carrier by

(14)
The unit dBc is the number of decibels relative to the residual carrier. For 100% modulation
( ), each sideband is dBc.
Demodulation of an AM carrier is normally done with an envelope detector. An envelope
detector, implemented as a rectifier followed by a low-pass filter, extracts the envelope of the
modulated carrier. For the modulated carrier of Eq. (10), the envelope is |

|.

Demodulator for AM

If ,

is always non-negative, so the envelope is just

. With AC
coupling (to remove the DC component) a scaled (and delayed) version of the original message
is recovered.
With overmodulation ( ), the envelope |

| does not equal

. In this
case, only a distorted version of the message can be recovered. However, if the overmodulation
is slight, then the distortion is slight.
PF
LPF rectifier
9

Ideally, AM should be used with close to . If is significantly greater than , then distortion
occurs in envelope detection at the receiver. If is significantly less than , then the system is
inefficient because an unnecessarily large fraction of the transmitted power is devoted to the
residual carrier, which contains no information about the message. It is the sidebands that
contain the information about the message; the residual carrier is only present to make distortion-
free envelope detection possible at the receiver.
Envelope detection, unlike synchronous detection, requires no carrier synchronization circuit in
the receiver. This is why AM was selected over DSB for broadcast radio. The goal was to
permit the many receivers of broadcast radio to be simple (and therefore cheap) and reliable.
1 DSB Modulation and Synchronous Detection
You will build a DSB modulator. This will be paired with a synchronous detector.
1.1 Sinusoidal Message
Initially, you will use a 5-kHz sinusoid as the message signal. Adjust the frequency of the Audio
Oscillator to approximately 5 kHz and place this message signal at one of the inputs of the
Multiplier. It is necessary that the Multiplier be set for DC coupling. Connect a 100-kHz
sinusoid (Master Signals) to the second input of the Multiplier. The output of the Multiplier is
the modulated carrier.
Simultaneously observe the message signal and the modulated carrier on the oscilloscope. Use
the TTL output from the Audio Oscillator as an external trigger source. This will stabilize the
envelope, but you will see that the fast carrier oscillation inside the envelope is not stabilized.
This is a consequence of the fact that the message sinusoid and the 100-kHz sinusoid are not
coherently related. (The message sinusoid has a frequency that is only approximately 5 kHz; it is
not exactly 100 kHz divided by 20.)
Switch to an XY View (Views > X-Axis > A). Verify that this view gives the correct
picture for DSB.
Select the Spectrum Mode. Note the frequencies of the two tall spectral lines.
Now you will demodulate the DSB carrier. Connect the modulated carrier to an input on a
different multiplier. You should use one of the multipliers in the Quadrature Utilities module for
this purpose. Place a 100-kHz sinusoid (Master Signals) on the input of a Phase Shifter.
Connect the Phase Shifter output to the second input of the (demodulator) multiplier. This
second input to the (demodulator) multiplier is known as the local oscillator; its frequency must
match that of the carrier if synchronous detection is to work. Connect the output of the
(demodulator) multiplier to a Tuneable LPF. Adjust the bandwidth of this filter to approximately
6 kHz.
10


Simultaneously observe the original 5-kHz message sinusoid (coming out of the Audio
Oscillator) and the Tuneable LPF output on the oscilloscope. Notice that the demodulator has
reproduced the original message, with some scaling and a delay. It should be possible to
stabilize simultaneously both sinusoids in the display since they share a common frequency.
Observe how the amplitude of the demodulator output varies as you vary the phase delay of the
Phase Shifter.
Adjust the Phase Shifter such that the local oscillator (at the input of the demodulator multiplier)
is in phase with the carrier. In order to make this adjustment, you will want to simultaneously
observe the Phase Shifter input (the unmodulated carrier) and the output (the local oscillator) on
the oscilloscope. Then measure the amplitude of the demodulator output.
Now adjust the Phase Shifter so that the local oscillator is in phase quadrature to the carrier (that
is, so that the local oscillator either lags or leads the carrier by

). Now measure the amplitude

of the demodulator output. Complete the following table.
Phase Offset Demodulator Output Amplitude

As you can see, synchronous detection requires that the local oscillator match the carrier in
frequency and approximately match it in phase. This is an important issue in receiver design.
For the purpose of this laboratory, the receiver has stolen a copy of the (unmodulated) carrier
from the transmitter. This is feasible as long as both transmitter and receiver are sitting in the
same laboratory. In the field, it is generally impossible for the receiver to steal a copy of the
(unmodulated) carrier from the transmitter. Instead, the receiver must perform carrier
synchronization.
1.2 Sum-of-Sinusoids Message
Generate a message signal that is a sum of sinusoids by the following procedure. First, create a
(100/96)-kHz clock by dividing the frequency of a (100/12)-kHz TTL clock (labeled as 8.3 kHz
on the Master Signals panel) by 8. (The Digital Utilities module provides circuits that divide the
frequency of a TTL signal by 4 and by 2.) With the Twin Pulse Generator set for single mode
PF x x LPF
message
carrier
stolen
carrier
modulator
demodulator
phase
shifter
local
oscillator
11

(on the PCB), clock this module with the (100/96)-kHz TTL signal. Every low-to-high transition
occurring on this clock will generate a narrow pulse on the Twin Pulse Generator output. Rotate
the width knob fully counter-clockwise, in order to produce the narrowest possible pulse. Place
the Twin Pulse Generator

output on the input of a Tuneable LPF. Adjust the bandwidth of

this filter to approximately 5 kHz. The output of this filter will be used as the message signal.
Observe this message signal on both the oscilloscope and the spectrum analyzer. On the
oscilloscope, the signal should look like a train of pulses, but these pulses are not rectangular in
shape because of the low-pass filtering. In the frequency domain, this signal should look like a
set of discrete spectral lines spaced about 1 kHz apart and up to approximately 5 kHz. This
message signal will be referred to as a sum-of-sinusoids.
Use the same configuration for the DSB modulator that you used above, except that the 5-kHz
message sinusoid should be replaced with the sum-of-sinusoids message signal. Place the
message signal on Channel A and the DSB modulator output on Channel B. Switch to an XY
view. This should have the characteristic shape of DSB modulation.
Simultaneously view the spectrum of the message signal and the spectrum of the modulated
carrier. You should observe the double sidebands of the latter.
Connect the DSB modulator output to the synchronous detector. Reset the phase offset between
the (unmodulated) carrier and local oscillator to

. If you wish, you can accomplish this by

simply removing the Phase Shifter, replacing it with a cable. Simultaneously observe the
message signal (from the transmitter side) and the demodulator output on the oscilloscope.
Notice that the demodulator has reproduced the original message, with some scaling and a delay.
1.3 Audio Message
Use an audio signal from the Speech module as the message signal. Otherwise, your
configuration will remain the same. Place the audio message signal on Channel A and the DSB
modulator output on Channel B. Switch to an XY view. This should have the characteristic
shape of DSB modulation.
Simultaneously view the spectrum of the audio message signal and the spectrum of the
modulated carrier. You should observe the double sidebands of the latter.

Connect the DSB modulator output to the synchronous detector. The phase offset between the
(unmodulated) carrier and the local oscillator should be

. Connect the demodulator output to

the headphones. Listen to the recovered audio message while varying the bandwidth of the
demodulator lowpass filter. Note the smallest bandwidth that still permits a sound of good
quality to come from the demodulator.
12

2 AM and Envelope Detection
You will build an AM modulator. This will be paired with an envelope detector.
2.1 Sinusoidal Message
Build a modulator for AM. Use a 5-kHz sinusoid from the Audio Oscillator as the message
signal. Use a weighted adder to combine the message signal and a DC component. The DC
component will come from the Variable DC panel, and the knob on this panel should be set
clockwise from the vertical position, so that a positive DC value is supplied. Connect the output
of the Adder to a Buffer Amplifier and the output of this amplifier to a multiplier (set for DC
coupling). The other input to the multiplier will be a 100-kHz sinusoid (Master Signals).
In the Adder, the gain on each input is negative. The purpose of the Buffer Amplifier, with its
negative gain, is to cancel minus signs so that the net gain through Adder and amplifier is
positive for both the DC component and the message signal. Care should be taken that the
absolute value of the gain is not set too high. If it is too high, saturation (overloading) can result.

Set the modulation index to . You can do this by measuring the rms voltage at the output of
Buffer Amplifier. First, measure the rms voltage with only the message signal present. Second,
measure the rms voltage with only the DC component present. Adjust one or both gain knobs on
the weighted adder until the ratio of the message signal measurement to the DC measurement is
approximately 0.707. See Eq. (12).
Simultaneously observe the 5-kHz message signal and the Buffer Amplifier output on the
oscilloscope. Then observe the 5-kHz message signal and the modulator output. Use the TTL
output from the Audio Oscillator as the trigger source. This will stabilize the display of the
envelope but not the fast carrier fluctuations inside the envelope.
Place the Buffer Amplifier output on Channel A and the modulator output on Channel B. Switch
to an XY view and observe the resulting figure.
Switch to the Spectrum Mode and observe the spectrum of the modulated carrier. Measure the
line height of the lower and upper sidebands. Use units of dBc (decibels below carrier).
PF
x
LPF message
carrier
modulator
demodulator
+
DC
rectifier
13

Connect the modulated carrier to a rectifier and the rectifier output to a Tuneable LPF. Adjust
the bandwidth of this filter to approximately 6 kHz. The combination of the rectifier and the
low-pass filter make an envelope detector. Simultaneously observe the message signal and the
rectifier output on the oscilloscope. Then observe the message signal and the envelope detector
output on the oscilloscope. For the envelope detector output, set the coupling for AC. (Now that
the envelope detection is done, the DC component is no longer needed.)
You will have noticed that no local oscillator (and therefore no stolen carrier) is required for
envelope detection. For an AM receiver, carrier synchronization is not required; and this
simplifies the receiver design.
Set the modulation index to the new value of 0.5 and repeat the above measurements.
Set the modulation index to the new value of 1.5 and repeat the above measurements. In this
case, the 5-kHz message signal will be distorted by the envelope detector. You should increase
the bandwidth of the Tuneable LPF (beyond the original bandwidth of 6 kHz) in order to get a
clear picture of this distortion.
Complete the following table.
Line Height of Upper Sideband (dBc) Predicted Line Height from Eq. (14)
1.0
0.5
1.5

2.2 Sum-of-Sinusoids Message
Generate a message signal that is a sum of sinusoids using the same procedure as was done for
the DSB experiment.
Use the same configuration for the AM modulator that you used above, except that the 5-kHz
message sinusoid should be replaced with the sum-of-sinusoids message signal. Place the Buffer
Amplifier output on Channel A and the AM modulator output on Channel B. Switch to an XY
view. Adjust the relative gains of the weighted adder in the modulator in order to achieve .
The XY view will help you make this adjustment.
Simultaneously view the message signal and the modulated carrier on the oscilloscope. You can
use the TTL signal that clocks the Twin Pulse Generator as the trigger source. This should
provide a stable display for the message signal and for the envelope of the modulated carrier.
Simultaneously view the spectrum of the message signal and the spectrum of the modulated
carrier.
14

Connect the AM modulator output to the envelope detector. As above, use a bandwidth of
approximately 6 kHz for the low-pass filter in the envelope detector. Simultaneously observe the
message signal (from the transmitter side) and the demodulator output on the oscilloscope.
Notice that the demodulator has reproduced the original message, with some scaling and a delay.
2.3 Audio Message
Use an audio signal from the Speech module as the message signal. Otherwise, your
configuration will remain the same.
Place the Buffer Amplifier output on Channel A and the AM modulator output on Channel B.
Switch to an XY view. Adjust the relative gains of the weighted adder in the modulator in order
to achieve . The XY view will help you make this adjustment.
Connect the AM modulator output to the envelope detector. Connect the demodulator output to
the headphones. Listen to the recovered audio message.
Repeat the above steps, but setting to a value less than 1 (that is, undermodulation).
Repeat the above steps, but setting to a value greater than 1 (that is, overmodulation).
Complete the following table, using adjectives like good, okay and poor.
Sound Quality of Recovered Message