0% found this document useful (0 votes)
170 views6 pages

Omron CJ CS CP

This document provides a guide for connecting OMRON CJ/CS/CP PLCs to HMI devices. It includes information on supported PLC models and communication protocols, recommended HMI settings, PLC settings, device address formats and ranges, and wiring diagrams. Device addresses covered include bits and words for areas like CIO, DM, HR, and extended memory. The guide also lists driver versions and their respective dates and descriptions.

Uploaded by

Gani Hartato
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
170 views6 pages

Omron CJ CS CP

This document provides a guide for connecting OMRON CJ/CS/CP PLCs to HMI devices. It includes information on supported PLC models and communication protocols, recommended HMI settings, PLC settings, device address formats and ranges, and wiring diagrams. Device addresses covered include bits and words for areas like CIO, DM, HR, and extended memory. The guide also lists driver versions and their respective dates and descriptions.

Uploaded by

Gani Hartato
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 6

PLC Connection Guide

OMRON CJ/CS/CP
Supported Series: OMRON CP1E,CP1L, CP1H, CJ 1M, CJ 2M, CJ 1H, CJ M1G, CS1H and
CS1G. (Host Link Protocol FINS command), this driver supports Extend Addressing Mode.

Website: http://oeiweb.omron.com/oei/Products-PLC.htm

HMI Setting:
Parameters Recommended Options Notes
PLC type OMRON CJ /CS/CP
PLC I/F RS232 RS232, RS422, RS485
Baud rate 9600 9600~115200
Data bits 7 7 or 8
Parity Even Even, Odd, None
Stop bits 2 1 or 2
PLC sta. no. 0 0-31 Host Link Station No.

Online simulator YES Extend address modeYES
Broadcast command NO
*Support communications between HMI and PLC in pass-through mode
*Set LW-9903 to 2 to enhance the speed of download/upload PLC program in
pass-through mode

PLC Setting:
Communication mode Host Link Protocol

Device Address:
Bit/Word Device type Format Range Memo
B CIO_Bit DDDDDdd 0 ~3276715 Channel I/O (CIO)
B W_Bit DDDDDdd 0 ~3276715 Work Area (WR)
B H_Bit DDDDDdd 0 ~3276715 Holding Area (HR)
B D_Bit DDDDDdd 0 ~3276715 Data Memory (DM)
B A_Bit DDDDDdd 0 ~3276715 Auxiliary Relay (AR)
B T_Bit DDDDDdd 0 ~3276715 Timer (TIM)
B C_Bit DDDDDdd 0 ~3276715 Counter (CNT)
PLC Connection Guide
Bit/Word Device type Format Range Memo
B C_flag DDDD 0 ~4095
B T_flag DDDD 0 ~4095
B LR_Bit DDDdd 0 ~19915
B
EM0_Bit ~
EMC_Bit
DDDDDdd 0 ~3276715 Extend Memory
W T DDDDD 0 ~32767 Timer (TIM)
W H DDDDD 0 ~32767 Holding Area (HR)
W D DDDDD 0 ~32767 Data Memory (DM)
W A DDDDD 0 ~32767 Auxiliary Relay (AR)
W W DDDDD 0 ~32767 Work Area (WR)
W C DDDDD 0 ~32767 Counter (CNT)
W CIO DDDDD 0 ~32767 Channel I/O (CIO)
W EM0 ~EMC DDDDD 0 ~32767 Extend Memory
W LR DDD 0 ~199

Wiring Diagram:
The following is the view from the soldering point of a cable.
9P D-Sub to 9P D-Sub:
eMT3000 series
COM1 RS232 9P
D-Sub Female
COM3 RS232 9P
D-Sub Female
RS232 9P D-Sub Male
2 RX 8 RX 2 SD
3 TX 7 TX 3 RD
5 GND 5 GND 9 GND
4 RS
5 CS
circuit




PLC Connection Guide
cMT series
COM1 RS232 9P
D-Sub Female
RS232 9P D-Sub Male
2 RX 2 SD
3 TX 3 RD
5 GND 9 GND
4 RS
5 CS
circuit



MT8000iE series
COM1 RS232 9P
D-Sub Female
RS232 9P D-Sub Male
2 RX 2 SD
3 TX 3 RD
5 GND 9 GND
4 RS
5 CS
circuit



MT6000/8000 series except MT6050i/MT8050i
COM1 RS232 9P
D-Sub Female
COM2 RS232 9P
D-Sub Female
COM3 RS232 9P
D-Sub Male
RS232 9P D-Sub Male
2 RX 6 RX 8 RX 2 SD
3 TX 4 TX 7 TX 3 RD
5 GND 5 GND 5 GND 9 GND
4 RS
5 CS
circuit


PLC Connection Guide
MT6050i/MT8050i
COM1 RS232 9P
D-Sub Female
RS232 9P D-Sub Male
9 RX 2 SD
6 TX 3 RD
5 GND 9 GND
4 RS
5 CS
circuit




The following is the view from the soldering point of a cable.
CP1H/CP1L CP1W-CIF11 RS485 4W : 9P D-Sub to Termainals:
eMT3000 series
COM1 RS485 4W
9P D-Sub Male
CP1W-CIF11 RS485
4W Terminal
1 RX- SDA
2 RX+ SDB
3 TX- RDA
4 TX+ RDB
5 GND FG



cMT series
COM2 RS485 4W
9P D-Sub Female
CP1W-CIF11 RS485
4W Terminal
7 RX- SDA
6 RX+ SDB
9 TX- RDA
8 TX+ RDB
5 GND FG



PLC Connection Guide
MT8000iE series
COM1 RS485 4W
9P D-Sub Male
CP1W-CIF11 RS485
4W Terminal
1 RX- SDA
2 RX+ SDB
3 TX- RDA
4 TX+ RDB
5 GND FG



MT6000/8000 series except MT6050i/MT8050i
COM1 RS485 4W
9P D-Sub Male
CP1W-CIF11 RS485
4W Terminal
1 RX- SDA
2 RX+ SDB
3 TX- RDA
4 TX+ RDB
5 GND FG



MT6050i/MT8050i
COM1 RS485 4W
9P D-Sub Female
CP1W-CIF11 RS485
4W Terminal
1 RX- SDA
2 RX+ SDB
3 TX- RDA
4 TX+ RDB
5 GND FG



CP1W-CIF11: SW1 ON, others OFF.

PLC Connection Guide
Driver Version:
Version Date Description
V1.90 Feb/01/2011 Added registers: LR, LR_Bit
V2.00 Dec/05/2012 Added register: EM_Bit

You might also like