Scribd
Upload
43 views3 pages

Dar Es Salaam Institute of Technology (Dit) : Etu 07209: Analogue Communication Laboratory

This document outlines an experiment on amplitude modulation and demodulation. The aims are to generate an amplitude modulated wave and determine the percentage modulation, and to demodulate the modulated wave using an envelope detector. The procedure involves assembling modulation and demodulation circuits, applying modulating and carrier signals, and observing the output waveforms. Key observations are made for over-modulation, under-modulation, and after connecting the demodulator circuit. Discussions are to be made based on the obtained waveforms.

Uploaded by

Romwald Lihakanga
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
43 views3 pages

Dar Es Salaam Institute of Technology (Dit) : Etu 07209: Analogue Communication Laboratory

This document outlines an experiment on amplitude modulation and demodulation. The aims are to generate an amplitude modulated wave and determine the percentage modulation, and to demodulate the modulated wave using an envelope detector. The procedure involves assembling modulation and demodulation circuits, applying modulating and carrier signals, and observing the output waveforms. Key observations are made for over-modulation, under-modulation, and after connecting the demodulator circuit. Discussions are to be made based on the obtained waveforms.

Uploaded by

Romwald Lihakanga
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 3

DAR ES SALAAM INSTITUTE OF TECHNOLOGY (DIT)

DEPARTMENT OF ELECTRONICS AND TELECOMMUNICATION


ETU 07209: ANALOGUE COMMUNICATION LABORATORY
LABORATORY TASK ONE
AMPLITUDE MODULATION & DEMODULATION
Aim
To generate amplitude modulated wave and determine the percentage modulation.
To demodulate the modulated wave using envelope detector.
T! "#$i%&%
Simulation software
Amplitude modulation & demodulation circuits
T'&#(
Refer reference books .
Ci#)*i+ %i,-#,m
Fi- .: Am"!i+*%& m%*!,+i/ Ci#)*i+
Fi- 2: E/$&!"& %&+&)+# )i#)*i+
0A91
100n
100k
PROCEDURE
1. Assemble components and make connections as shown in figure 1.
2. Set modulating signal at 1kH with 1.!" amplitude and #arrier signal of $%kH with &"
amplitude.
&. Appl' the sine wave of modulating signal and carrier signal to the circuit.
(. )bserve the resulting amplitude modulated signal on #R).
OBSER0ATION IN MODULATING CIRCUIT
T,1!& .
"oltage signal *re+uenc' Amplitude
,odulating signal
#arrier signal
T,1!& 2
0
m,2
0
mi/
M%*!,+i/ I/%&2 3 4 M%*!,+i/

Di5)*55i/
1. "ar' amplitude of modulating signal to get over-modulation. 1%%/ modulation
condition with the help of waveforms obtained discuss the observation made.
2. "ar' amplitude of modulating signal to get under-modulation. condition. 0ith the help
of waveforms obtained discuss the observation made.
&. 1ote the similarit' 23ifferences in the observations and comment on the results.
OBSER0ATION AFTER CONNECTING DEMODULATOR CIRCUIT
AM 5i-/,!:
#arrier fre+uenc' 4
"ma5 4
"min 4
D&m%*!,+&% Si-/,!:
*re+uenc' 4
Amplitude 4
Di5)*55i/
0ith the help of obtained waveforms. discuss all the observation made.
P#&),*+i/5:
1. #heck the connections before undergoing an' measurement.
2. )bservations should be done carefull'.

You might also like