DATA SHEET

Operational amplifiers
Order code Manufacturer code Description
82-0050 TLO72CN TL072 BI-FET DUAL OP AMPLIFIER

Operational amplifiers Page 1 of 10

The enclosed information is believed to be correct, Information may change ‘without notice’ due to Revision A
product improvement. Users should ensure that the product is suitable for their use. E. & O. E. 04/07/2003

Sales: 01206 751166 Technical: 01206 835555 Fax: 01206 7551188

[email protected] [email protected] www.rapidelectronics.co.uk
 TL072
TL072A - TL072B
LOW NOISE
DUAL J-FET OPERATIONAL AMPLIFIERS

.. LOW POWER CONSUMPTION

WIDE COMMON-MODE (UP TO VCC+) AND

.. DIFFERENTIAL VOLTAGE RANGE

LOW INPUT BIAS AND OFFSET CURRENT

.. LOW NOISE en = 15nV/√Hz (typ)

OUTPUT SHORT-CIRCUIT PROTECTION
HIGH INPUT IMPEDANCE J–FET INPUT

.. STAGE
LOW HARMONIC DISTORTION : 0.01% (typ)

.. INTERNAL FREQUENCY COMPENSATION

LATCH UP FREE OPERATION
HIGH SLEW RATE : 16V/µs (typ)
N
DIP8
D
SO8
(Plastic Package) (Plastic Micropackage)

DESCRIPTION ORDER CODES

The TL072, TL072A and TL072B are high speed Temperature Package
J–FET input dual operational amplifiers incorporating Part Number
Range N D
well matched, high voltage J–FET and bipolar transis-
TL072M/AM/BM –55oC, +125oC • •
tors in a monolithic integrated circuit. o o
TL072I/AI/BI –40 C, +105 C • •
The devicesfeaturehigh slew rates, low input bias and

072-01.TBL
offset current, and low offset voltage temperature TL072C/AC/BC o
0 C, +70 C o
• •
coefficient. Example : TL072CN

PIN CONNECTIONS (top view)

1 8 1 - Output 1
2 - Inverting input 1
2 7 3 - Non-inverting input 1
- -
4 - VCC
5 - Non-inverting input 2
3 + - 6 6 - Inverting input 2
7 - Output 2
+
8 - VCC
4 + 5

November 1995 1/9

TL072 - TL072A - TL072B

SCHEMATIC DIAGRAM

VCC

No n- inver t ing
i nput
I nver t ing
input
1 0 0Ω
20 0 Ω
Output

1 0 0Ω
30k 1/2 T L072

8.2k

1.3k 35k 1.3k 35k 1 0 0Ω

V CC

ABSOLUTE MAXIMUM RATINGS 072-03.EPS

Symbol Parameter Value Unit

VCC Supply Voltage - (note 1) ±18 V
Vi Input Voltage - (note 3) ±15 V
Vid Differential Input Voltage - (note 2) ±30 V
Ptot Power Dissipation 680 mW
Output Short-circuit Duration - (note 4) Infinite
o
Toper Operating Free Air Temperature Range TL072C,AC,BC 0 to 70 C
TL072I,AI,BI –40 to 105
072-02.TBL

TL072M,AM,BM –55 to 125

o
Tstg Storage Temperature Range –65 to 150 C
Notes : 1. All voltage values, except differential voltage, are with respect to the zero reference level (ground) of the supply voltages where the
zero reference level is the midpoint between VCC+ and VCC–.
2. Differential voltages are at the non-inverting input terminal with respect to the inverting input terminal.
3. The magnitude of the input voltage must never exceed the magnitude of the supply voltage or 15 volts, whichever is less.
4. The output may be shorted to ground or to either supply. Temperature and /or supply voltages must be limited to ensure that the
dissipation rating is not exceeded.

2/9
 TL072 - TL072A - TL072B

ELECTRICAL CHARACTERISTICS
VCC = ±15V, Tamb = 25oC (unless otherwise specified)
TL072I,M,AC,AI,
TL072C
Symbol Parameter AM,BC,BI,BM Unit
Min. Typ. Max. Min. Typ. Max.
Vio Input Offset Voltage (R S = 50Ω) mV
o
Tamb = 25 C 3 6 3 10
TL072BC,BI,BM 1 3
Tmin. ≤ Tamb ≤ Tmax. 7 13
TL072BC,BI,BM 5
o
DV io Input Offset Voltage Drift 10 10 µV/ C
Iio Input Offset Current *
Tamb = 25oC 5 100 5 100 pA
Tmin. ≤ Tamb ≤ Tmax. 4 10 nA
Iib Input Bias Current *
o
Tamb = 25 C 20 200 20 200 pA
Tmin. ≤ Tamb ≤ Tmax. 20 20 nA
Avd Large Signal Voltage Gain (RL = 2kΩ, VO = ±10V) V/mV
Tamb = 25oC 50 200 25 200
Tmin. ≤ Tamb ≤ Tmax. 25 15
SVR Supply Voltage Rejection Ratio (R S = 50Ω) dB
Tamb = 25oC 80 86 70 86
Tmin. ≤ Tamb ≤ Tmax. 80 70
ICC Supply Current, per Amp, no Load mA
Tamb = 25oC 1.4 2.5 1.4 2.5
Tmin. ≤ Tamb ≤ Tmax. 2.5 2.5
Vicm Input Common Mode Voltage Range ±11 +15 ±11 +15 V
-12 -12
CMR Common Mode Rejection Ratio (RS = 50Ω) dB
o
Tamb = 25 C 80 86 70 86
Tmin. ≤ Tamb ≤ Tmax. 80 70
Ios Output Short-circuit Current mA
Tamb = 25oC 10 40 60 10 40 60
Tmin. ≤ Tamb ≤ Tmax. 10 60 10 60
±VOPP Output Voltage Swing V
Tamb = 25oC RL = 2kΩ 10 12 10 12
RL = 10kΩ 12 13.5 12 13.5
Tmin. ≤ Tamb ≤ Tmax. RL = 2kΩ 10 10
RL = 10kΩ 12 12
SR Slew Rate (Vin = 10V, RL = 2kΩ, CL = 100pF, V/µs
Tamb = 25oC, unity gain) 8 16 8 16
tr Rise Time (Vin = 20mV, RL = 2kΩ, C L = 100pF, µs
o
Tamb = 25 C, unity gain) 0.1 0.1
KOV Overshoot (Vin = 20mV, RL = 2kΩ, C L = 100pF, %
Tamb = 25oC, unity gain) 10 10
GBP Gain Bandwidth Product (f = 100kHz, MHz
o
Tamb = 25 C, Vin = 10mV, R L = 2kΩ, C L = 100pF) 2.5 4 2.5 4
Ri Input Resistance 1012 1012 Ω
THD Total Harmonic Distortion (f = 1kHz, AV = 20dB, %
o
RL = 2kΩ, C L = 100pF, Tamb = 25 C, VO = 2VPP) 0.01 0.01
Equivalent Input Noise Voltage nV
en 15 15
(f = 1kHz, Rs = 100Ω) √
 Hz
072-03.TBL

∅m Phase Margin 45 45 Degrees

VO1/VO2 Channel Separation (Av = 100) 120 120 dB
* The input bias currents are junction leakage currents which approximately double for every 10oC increase in the junction temperature.

3/9
TL072 - TL072A - TL072B

MAXIMUM PEAK-TO-PEAK OUTPUT MAXIMUM PEAK-TO-PEAK OUTPUT

VOLTAGE VERSUS FREQUENCY VOLTAGE VERSUS FREQUENCY

MAXIMUMPEAK-TO-PEAK OUTPUT
30
30
V CC = 15V R L = 2kΩ R L= 10kΩ
MAXIMUM PEAK-TO-PEAKOUTPUT

25 T a m b = + 25° C 25 Tamb = +25 C

V CC = 15V
S ee Fig ure 2 See Figure 2
20

VOLTAGE (V)
20
VOLTAGE (V)

V CC = 10V VCC = 10V

15 15
10 10
V CC = 5V V CC = 5V
5 5
0 0
100 1K 10K 100K 1M 10M 100 1K 10K 100K 1M 10M

072-05.EPS
072-04.EPS
FREQUENCY (Hz) FREQUENCY (Hz)

MAXIMUM PEAK-TO-PEAK OUTPUT MAXIMUM PEAK-TO-PEAK OUTPUT

VOLTAGE VERSUS FREQUENCY VOLTAGE VERSUS FREE AIR TEMP.
MAXIMUMPEAK-TO-PEAK OUTPUT

30
30
MAXIMUM PEAK-TO-PEAKOUTPUT

Ta mb = +25 C VCC = 15V

25
R L = 2kΩ 25
VOLTAGE (V)

20 S ee Figure 2
20
VOLTAGE (V)

R L = 1 0 kΩ
15 15
Ta mb = -55 C R L = 2 kΩ
10 10

5 5 VC C = 15 V
Ta mb = +125 C S e e F i g u re 2
0 0
10k 40k 100k 400k 1M 4M 10M -7 5 -5 0 - 25 0 25 50 75 -50 125

T E MP ER AT U R E ( ° C )
072-06.EPS

072-07.EPS
FREQUENCY (Hz)

MAXIMUM PEAK-TO-PEAK OUTPUT MAXIMUM PEAK-TO-PEAK OUTPUT

VOLTAGE VERSUS LOAD RESISTANCE VOLTAGE VERSUS SUPPLY VOLTAGE

30 30
MAXIMUM PEAK-TO-PEAK OUTPUT

MAXIMUM PEAK-TO-PEAKOUTPUT

VCC = 15V
25 Tamb = +25°C
RL = 10 kΩ
25
See Figure 2 Tamb = +25°C
20
VOLTAGE (V)

20
VOLTAGE (V)

15 15
10
10
5
5
0
0.1 0.2 0.4 0.7 1 2 4 7 10 0 2 4 6 8 10 12 14 16
SUPPLY VOLTAGE ( V)
LOAD RESISTANCE (k Ω)
072-08.EPS

072-09.EPS

4/9
 TL072 - TL072A - TL072B

INPUT BIAS CURRENT VERSUS LARGE SIGNAL DIFFERENTIAL

FREE AIR TEMPERATURE VOLTAGE AMPLIFICATION VERSUS
FREE AIR TEMPERATURE

100 1000
V CC = 15V
400
INPUT BIAS CURRENT (nA)

10 200

DIFFERENTIAL VOLTAGE
AMPLIFICATION (V/V)
100

1 40
20
10 V CC = 15V
0.1 VO = 10V
4
2 R = 2k Ω
L

0.01 1
-75 -50 -25 0 25 50 75 100 125
-50 -25 0 25 50 75 100 125

072-11.EPS
072-10.EPS
TEMPERATURE (°C)
TEMPERATURE (°C)

LARGE SIGNAL DIFFERENTIAL TOTAL POWER DISSIPATION VERSUS

VOLTAGE AMPLIFICATION AND PHASE FREE AIR TEMPERATURE
SHIFT VERSUS FREQUENCY

250
DIFFERENTIAL VOLTAGE

225 V CC = 15V
TOTAL POWER DISSIPATION (mW)

100
AMPLIFICATION(V/V)

DIFFERENTIAL 180
200 No signal
VOLTAGE
PHASE SHIFT AMPLIFICATION 175 No load
(right s ca le ) (left s ca le)
150
10 90 125
R = 2kΩ 100
L
C L = 100pF 75
1 V CC = 15V 0 50
T amb = +125 C 25
0
100 1K 10K 100K 1M 10M -75 -50 -25 0 50 75 100 125
25
072-12.EPS

072-13.EPS
FREQUENCY (Hz)
TEMPERATURE (°C)

SUPPLY CURRENT PER AMPLIFIER COMMON MODE REJECTION RATIO

VERSUS FREE AIR TEMPERATURE VERSUS FREE AIR TEMPERATURE

2.0 89
1.8 V CC = 15V R L = 1 0 kΩ
COMMON MODE MODE REJECTION

1.6 No signal 88
VC C = 1 5V
SUPPLY CURRENT (mA)

1.4 No load
87
1.2
RATIO (dB)

1.0 86
0.8
0.6 85

0.4
84
0.2
0 83
-75 -50 -25 0 25 50 75 100 125
-75 -50 -25 0 25 50 75 100 125
072-15.EPS
072-14.EPS

TEMPERATURE (°C) TEMPERATURE (°C)

5/9
TL072 - TL072A - TL072B

VOLTAGE FOLLOWER LARGE SIGNAL OUTPUT VOLTAGE VERSUS

PULSE RESPONSE ELAPSED TIME

28
INPUT AND OUTPUT VOLTAGES

6
24
4 OUTP UT OVERSHOOT

OUTPUT VOLTAGE (mV)

INPUT 20 90%

2 16
(V)

0 12
VCC = 15 V 8
-2 R L = 2 kΩ V = 15V
CC
4
C L= 100pF R L = 2k Ω
-4 10%
Tamb = +25 C 0 Tamb = +25°C
-6 t r
-4
0 0.5 1 1.5 2 2.5 3 3.5 0.3 0.5 0.6
0 0.1 0.2 0.4 0.7
TIME (µs )
072-16.EPS

072-17.EPS
TIME ( µs)

EQUIVALENT INPUT NOISE VOLTAGE TOTAL HARMONIC DISTORTION VERSUS

VERSUS FREQUENCY FREQUENCY

70 1
VCC = 15V V VCC = = 15V
15V
TOTAL HARMONIC DISTORTION

60 CC
A V = 10 0.4
V V= =
11
EQUIVALENT INPUT NOISE

AA
50 R S = 100 Ω VV
O (rms) = =
6V6V
VOLTAGE (nV/VHz)

0.1 O (rms)
T amb = +25°C T amb
T amb= =+25°C
+25°C
40
0.04
(%)

30
0.01
20
0.004
10

0 0.001
10 40 100 400 1k 4k 10k 40k 100k 100 400 1k 4k 10k 40k 100k
072-18.EPS

072-19.EPS
FREQUENCY (Hz) FREQUENCY (Hz)

6/9
 TL072 - TL072A - TL072B

PARAMETER MEASUREMENT INFORMATION

Figure 1 : Voltage Follower Figure 2 : Gain-of-10 Inverting Amplifier

10k Ω

- 1k Ω
eI -
1/2
- eo 1/2
TL072
TL072 eo

CL = 100pF RL = 2kΩ
eI RL CL = 100pF

072-21.EPS
072-20.EPS

TYPICAL APPLICATION
100KHz QUADRUPLE OSCILLATOR

18k Ω*
1N 4148
-15V

18pF 1k Ω
18pF

-
1/2 88.4k Ω
TL072 -

1/2
88.4k Ω 6 cos ωt
TL072
6 sin ωt
1k Ω
18pF

88.4k Ω
1N 4148
18k Ω*

+15V
072-22.EPS

* These resistor values may be adjusted for a symmetrical output

7/9
TL072 - TL072A - TL072B

PACKAGE MECHANICAL DATA

8 PINS - PLASTIC DIP

PM-DIP8.EPS
Millimeters Inches
Dimensions
Min. Typ. Max. Min. Typ. Max.
A 3.32 0.131
a1 0.51 0.020
B 1.15 1.65 0.045 0.065
b 0.356 0.55 0.014 0.022
b1 0.204 0.304 0.008 0.012
D 10.92 0.430
E 7.95 9.75 0.313 0.384
e 2.54 0.100
e3 7.62 0.300
e4 7.62 0.300
F 6.6 0260
i 5.08 0.200
DIP8.TBL

L 3.18 3.81 0.125 0.150

Z 1.52 0.060

8/9
 TL072 - TL072A - TL072B

PACKAGE MECHANICAL DATA

8 PINS - PLASTIC MICROPACKAGE (SO)

PM-SO8.EPS
Millimeters Inches
Dimensions
Min. Typ. Max. Min. Typ. Max.
A 1.75 0.069
a1 0.1 0.25 0.004 0.010
a2 1.65 0.065
a3 0.65 0.85 0.026 0.033
b 0.35 0.48 0.014 0.019
b1 0.19 0.25 0.007 0.010
C 0.25 0.5 0.010 0.020
o
c1 45 (typ.)
D 4.8 5.0 0.189 0.197
E 5.8 6.2 0.228 0.244
e 1.27 0.050
e3 3.81 0.150
F 3.8 4.0 0.150 0.157
L 0.4 1.27 0.016 0.050
M 0.6 0.024
SO8.TBL

o
S 8 (max.)

Information furnished is believed to be accurate and reliable. However, SGS-THOMSON Microelectronics assumes no responsi-
bility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which
may result from its use. No licence is granted by implication or otherwise under any patent or patent rights of SGS-THOMSON
Microelectronics. Specifications mentioned in this publ ication are subject to change without notice. This pub lication supersedes
and replaces all information previously supplied. SGS-THOMSON Microelectronics products are not authorized for use as critical
components in life support devices or systems without express written approval of SGS-THOMSON Microelectronics.

 1995 SGS-THOMSON Microelectronics - All Rights Reserved

ORDER CODE :

SGS-THOMSON Microelectronics GROUP OF COMPANIES

Australia - Brazil - France - Germany - Hong Kong - Italy - Japan - Korea - Malaysia - Malta - Morocco - The Netherlands
Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A.

9/9