Veritas Netbackup 6.0 For NDMP: System Administrator'S Guide

VERITAS NetBackup 6.
0 for NDMP
System Administrators Guide
for UNIX, Windows, and Linux
N15271C September 2005
Disclaimer The information contained in this publication is subject to change without notice. VERITAS Software Corporation makes no warranty of any kind with regard to this manual, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. VERITAS Software Corporation shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this manual. VERITAS Legal Notice Copyright 2002 - 2005 VERITAS Software Corporation. All rights reserved. VERITAS, the VERITAS Logo, and NetBackup are trademarks or registered trademarks of VERITAS Software Corporation or its affiliates in the U.S. and other countries. Other names may be trademarks of their respective owners. Portions of this software are derived from the RSA Data Security, Inc. MD5 Message-Digest Algorithm. Copyright 1991-92, RSA Data Security, Inc. Created 1991. All rights reserved. VERITAS Software Corporation 350 Ellis Street Mountain View, CA 94043 USA Phone 650-527-8000 Fax 650-527-2908 www.veritas.com Third-Party Copyrights For a list of third-party copyrights, see the NetBackup Release Notes appendix.
ii
NetBackup for NDMP System Administrators Guide
Contents
Getting Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .vii Finding NetBackup Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .vii Accessing the VERITAS Technical Support Web Site . . . . . . . . . . . . . . . . . . . . . . . . viii Contacting VERITAS Licensing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix Accessibility Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix Comment on the Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . x NetBackup for NDMP Information on the Web . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . x Advanced Client Information on the Web . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . x Chapter 1. Introduction to NetBackup for NDMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 NetBackup for NDMP Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 NetBackup for NDMP Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Network Data Management Protocol (NDMP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Types of NDMP Backup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 NDMP Local Backup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 NDMP Three-Way Backup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Backup to Media Manager Storage Devices (Remote NDMP) . . . . . . . . . . . . . . . . . . 9 NDMP Policies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Storage Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 NDMP Storage Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Media Manager Storage Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Assigning Tape Drives to Different Hosts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 NDMP Backup Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 NDMP Restore Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
iii
Direct Access Recovery (DAR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Chapter 2. Installing NetBackup for NDMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Installation Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Installing on UNIX Servers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Installing on Windows Servers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Uninstalling NetBackup for NDMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Chapter 3. Configuring NDMP Backup to NDMP-Attached Devices . . . . . . . . . . . . 23 Authorizing Access to the NDMP Host . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Access for Three-Way Backups and NDMP to Media Manager . . . . . . . . . . . . . . . 27 Media Manager Device Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Adding a Robot Directly Attached to an NDMP Host . . . . . . . . . . . . . . . . . . . . . . . 28 Adding a Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Checking a Media Manager Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Adding Volumes to a Media Manager Configuration . . . . . . . . . . . . . . . . . . . . . 33 Verifying NDMP Password and/or Robot Connection . . . . . . . . . . . . . . . . . . . . . . . . . 34 Adding NDMP Storage Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Creating an NDMP Policy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Attributes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Clients . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Schedules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Using Environment Variables in Backup Selections list . . . . . . . . . . . . . . . . . . . 38 Enabling/Disabling DAR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Setting Up Clustering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Post-Installation Changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Testing an NDMP Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Chapter 4. Configuring NDMP Backup to NetBackup Media Servers . . . . . . . . . . . 45 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
iv NetBackup for NDMP System Administrators Guide
Configuring NDMP Backup to Media Manager Devices . . . . . . . . . . . . . . . . . . . . . . . . 47 Chapter 5. Using The Shared Storage Option (SSO) . . . . . . . . . . . . . . . . . . . . . . . . . 49 Shared Storage Option (SSO): Basic Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 Setting up SSO: Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 Using the Device Configuration Wizard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 Chapter 6. Backup and Restore Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 Performing an NDMP Backup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 Automatic Backup of an NDMP Policy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 Manual Backup of an NDMP Policy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 Performing a Restore from the Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 Chapter 7. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 NDMP Operating Notes and Restrictions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 Notes on DAR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 Troubleshooting NetBackup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 Types of Logs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 Troubleshooting Steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 NDMP Backup Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 Troubleshooting Media Manager on Windows Systems . . . . . . . . . . . . . . . . . . . . . . . . . 63 Troubleshooting Media Manager on UNIX systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 Troubleshooting DAR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 Testing a Robot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 Chapter 8. Using Scripts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 ndmp_start_notify (UNIX) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 ndmp_start_notify.cmd (Microsoft Windows) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 ndmp_end_notify (UNIX) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 ndmp_end_notify.cmd (Microsoft Windows) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 ndmp_start_path_notify (UNIX) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Contents
ndmp_start_path_notify.cmd (Microsoft Windows) . . . . . . . . . . . . . . . . . . . . . . . . . 80 ndmp_end_path_notify (UNIX) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82 ndmp_end_path_notify.cmd (Microsoft Windows) . . . . . . . . . . . . . . . . . . . . . . . . . 84 ndmp_moving_path_notify (UNIX) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86 ndmp_moving_path_notify.cmd (Microsoft Windows) . . . . . . . . . . . . . . . . . . . . . . 88 Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
vi
Preface
This guide explains how to install, configure, and use VERITAS NetBackup for NDMP (Network Data Management Protocol). In this guide, VERITAS NetBackup is referred to as NetBackup. This guide is intended for the system administrator responsible for installing, configuring, and using NetBackup for NDMP, and assumes a thorough working knowledge of how to administer both NetBackup and the NDMP host platform.
Getting Help
You can find answers to questions and get help from the NetBackup documentation and from the VERITAS technical support web site.
Finding NetBackup Documentation

A list of the entire NetBackup documentation set appears as an appendix in the NetBackup Release Notes. All NetBackup documents are included in PDF format on the NetBackup Documentation CD. For definitions of NetBackup terms, consult the online glossary.
To access the NetBackup online glossary 1. In the NetBackup Administration Console, click Help > Help Topics. 2. Click the Contents tab. 3. Click Glossary of NetBackup Terms. Use the scroll function to navigate through the glossary.
vii
Getting Help
Accessing the VERITAS Technical Support Web Site

The address for the VERITAS Technical Support Web site is http://support.veritas.com. The VERITAS Support Web site lets you do any of the following:

Obtain updated information about NetBackup, including system requirements, supported platforms, and supported peripherals Contact the VERITAS Technical Support staff and post questions to them Get the latest patches, upgrades, and utilities View the NetBackup Frequently Asked Questions (FAQ) page Search the knowledge base for answers to technical support questions Receive automatic notice of product updates Find out about NetBackup training Read current white papers related to NetBackup
From http://support.veritas.com, you can complete various tasks to obtain specific types of support for NetBackup: 1. Subscribe to the VERITAS Email notification service to be informed of software alerts, newly published documentation, Beta programs, and other services. a. From the main http://support.veritas.com page, select a product family and a product. b. Under Support Resources, click Email Notifications. Your customer profile ensures you receive the latest VERITAS technical information pertaining to your specific interests. 2. Locate the telephone support directory at http://support.veritas.com by clicking the Phone Support icon. A page appears that contains VERITAS support numbers from around the world. Note Telephone support for NetBackup is only available with a valid support contract. To contact VERITAS for technical support, dial the appropriate phone number listed on the Technical Support Guide included in the product box and have your product license information ready for quick navigation to the proper support group. 3. Contact technical support using e-mail.
viii
Accessibility Features
a. From the main http://support.veritas.com page, click the E-mail Support icon. A wizard guides you to do the following:

Select a language of your preference Select a product and a platform Provide additional contact and product information, and your message Associate your message with an existing technical support case
b. After providing the required information, click Send Message.
Contacting VERITAS Licensing

For license information, you can contact us as follows:

Call 1-800-634-4747 and select option 3 Fax questions to 1-650-527-0952 In the Americas, send e-mail to [email protected]. In the Asia and Pacific areas, send email to [email protected]. In all other areas, send email to [email protected].
Accessibility Features
NetBackup contains features that make the user interface easier to use by people who are visually impaired and by people who have limited dexterity. Accessibility features include:

Support for assistive technologies such as screen readers and voice input (Windows servers only) Support for keyboard (mouseless) navigation using accelerator keys and mnemonic keys
For more information, see the NetBackup Installation Guide.
Preface
ix
Comment on the Documentation
Comment on the Documentation

Let us know what you like and dislike about the documentation. Were you able to find the information you needed quickly? Was the information clearly presented? You can report errors and omissions or tell us what you would find useful in future versions of our manuals and online help. Please include the following information with your comment:

The title and product version of the manual on which you are commenting The topic (if relevant) on which you are commenting Your comment Your name
Email your comment to [email protected]. Please only use this address to comment on product documentation. See Getting Help in this preface for information on how to contact Technical Support about our software. We appreciate your feedback.
NetBackup for NDMP Information on the Web

The VERITAS support web site has a pdf document about supported NDMP operating systems and NAS vendors. It also contains configuration and troubleshooting help for particular NAS systems. Go to www.support.veritas.com and enter NAS Appliance in the search field. The title of the document is: NetBackup for NDMP Supported OS and NAS Appliance Information.
Advanced Client Information on the Web

The VERITAS support web site has a pdf document about Advanced Client containing a list of NAS vendors currently supported for the NAS_Snapshot method and for SnapVault, along with configuration notes. Go to www.support.veritas.com and enter Advanced client configuration in the search field. The title of the document is: VERITAS NetBackup Advanced Client Configuration and Compatibility.
Introduction to NetBackup for NDMP

NetBackup for NDMP is an optional application that enables NetBackup to use the Network Data Management Protocol (NDMP) to initialize and control backups and restores of Network Attached Storage (NAS) systems. This chapter contains the following topics.

NetBackup for NDMP Features NetBackup for NDMP Terminology Network Data Management Protocol (NDMP) Types of NDMP Backup NDMP Policies Storage Units NDMP Backup Process NDMP Restore Process Direct Access Recovery (DAR)
NetBackup for NDMP Features

NetBackup for NDMP includes the following features:

Support for NDMP protocol versions V2, V3, and V4. Centralized backup-policy management Scheduling, catalog management, and other backup tasks are managed from a NetBackup master server. NetBackup for NDMP may be installed on a NetBackup master or media server.
Device and media management NetBackup Media Manager software provides complete management and control of the devices and media used for backups and restores of NDMP hosts. The NetBackup Device Configuration wizard can discover and configure storage devices that are attached to an NDMP host (requires NDMP protocol versions V3 or V4). Note that wizard-based discovery depends upon a number of device-specific features, such as SCSI inquiry and serialization, which may not be supported by all NAS vendors.
High speed local backup of NDMP hosts Backup data travels between disk and tape drives that are directly attached to the same NDMP host. This provides high-speed backup without impairing network throughput.
Backup of network-attached NDMP hosts to a tape device on another NDMP host or to advanced tape libraries with embedded NDMP server. Backup data travels across the network, from a disk on an NDMP host to tape on another NDMP host. This is referred to as three-way backup. This data movement option requires support from the NAS/NDMP host.
Backup of a network-attached NDMP host to a tape device on a NetBackup media server. This is a form of three-way backup also known as remote NDMP. This feature supports NDMP versions V2, V3, and V4 on the NDMP hosts. Shared tape libraries Tape libraries can be shared between NDMP hosts and NetBackup servers, or between multiple NDMP hosts. Robotic control can be on an NDMP host or on a NetBackup server.
Shared tape drives with the Shared Storage Option Tape drives can be shared between servers (both NetBackup servers and NDMP hosts). This requires the Shared Storage Option (SSO) license. To see if your NAS vendor supports SSO, refer to the NetBackup for NDMP Supported OS and NAS Appliance Information document (see NetBackup for NDMP Information on the Web on page x for help accessing this document).
Snapshots of data on NDMP hosts NetBackup can make point-in-time snapshots of data on an NDMP (NAS) host without interrupting client access to the data, using the NDMP V4 snapshot extension. The snapshot is stored on the same device that contains the NDMP client data. From the snapshot, you can restore individual files or roll back a file system or volume, by means of Advanced Client Instant Recovery. A NetBackup Advanced Client license is required, in addition to the NetBackup for NDMP license. This Advanced Client feature uses the NAS_Snapshot method. Refer to the NetBackup Advanced Client System Administrators Guide for details.
NetBackup can also create a SnapVault disk copy from a NAS snapshot. Configuration details are contained in the NetBackup Advanced Client System Administrators Guide. For a list of NAS vendors that NetBackup currently supports for SnapVault and NAS_Snapshot, refer to the Advanced Client Configuration and Compatibility online document (see the preface of this manual for help accessing that document).
Direct Access Recovery (DAR) For NDMP hosts that support DAR, this feature can greatly reduce the time it takes to restore a single file or small number of files.
Path-based file history The NDMP server can send catalog information consisting of complete path names to NetBackup. This feature is not supported by all vendors. For up-to-date information on the vendors supporting path-based history, refer to NetBackup for NDMP Information on the Web on page x.
NetBackup for NDMP servers are supported in a NetBackup clustered environment. The enhanced ability to execute customized scripts during a backup, especially for relational databases residing on NAS devices.
Chapter 1, Introduction to NetBackup for NDMP
NetBackup for NDMP Terminology

This section introduces NetBackup for NDMP terminology. For explanations of other NetBackup terms, consult the NetBackup online glossary in NetBackup help. DAR (Direct Access Recovery) The NDMP host positions the tape to the exact location of the requested file(s), reading only the data needed for those files. Restore times can be reduced from hours to minutes. NDMP (Network Data Management Protocol) NDMP is a widely used protocol through which an NDMP-conformant backup application can control the backups and restores for an NDMP host. NDMP Backup to Media Manager Devices This is a form of three-way backup/restore also known as Remote NDMP, in which data travels from an NDMP host to a tape drive attached to a NetBackup media server. NDMP Client An NDMP client is an NDMP-compliant backup application (also known as a Data Management Application or DMA) that is a client of an NDMP server application. An NDMP client sends commands to the NDMP server application to control the backups and restores on an NDMP host. NetBackup for NDMP is an application that allows NetBackup to be an NDMP client. NetBackup for NDMP Server A NetBackup for NDMP server is a NetBackup master or media server that has NetBackup for NDMP software installed on it. NDMP Host A NAS system that serves files to clients using HTTP, FTP, CIFS, or NFS protocols. It also runs an NDMP server application that communicates with NDMP client backup software to configure and perform backup and restore tasks. NAS systems are designed to provide fast, multi-protocol file access and cost effective data storage to workstations and servers in the network or across the Internet. In a NetBackup configuration, the NDMP host is considered a client of NetBackup. However, NetBackup client software is never installed on an NDMP host. NDMP Server Application An NDMP server application runs on an NDMP host and executes backup, restore, and device control commands that it receives from an NDMP-conformant backup application. The backup application (NetBackup) is considered an NDMP client.
A separate instance of an NDMP server process exists for each connection to an NDMP client. That is, if two backups are in progress, an NDMP server process exists for each backup. NDMP Storage Unit An NDMP storage unit stores the backup data for an NDMP host. The tape drives in this storage unit attach directly to the NDMP host or can be configured on a SAN. Note that NDMP storage units cannot be used to store data for non-NDMP hosts, and NetBackup disk storage units cannot be used for NDMP tasks. Redirected Restore (to a Different Client) In a redirected restore, files are restored to a client other than the one from which they were originally backed up. In NetBackup for NDMP, this means the restore data travels from an NDMP host (or NetBackup media server) with a locally attached storage device to another NDMP host on the network. Remote NDMP See NDMP Backup to Media Manager Devices. Three-Way Backup/Restore In a three-way backup or restore, data travels between an NDMP host and a storage device attached to another NDMP host or to a NetBackup media server. This contrasts with local NDMP backup/restore, where the data travels between an NDMP hosts disk and a storage device directly attached to the same NDMP host.
Network Data Management Protocol (NDMP)
Network Data Management Protocol (NDMP)

NDMP is a widely used protocol through which an NDMP-conformant backup application can control the backups and restores of any NDMP host that is running an NDMP server application. NDMP architecture follows the client/server model:

The NetBackup master or media server that has NetBackup for NDMP installed is called a NetBackup for NDMP server. The host where the NDMP server application resides is called an NDMP host. The NetBackup software is a client of the NDMP server application. The NetBackup for NDMP application allows NetBackup to be an NDMP client. The NDMP hosts, on the other hand, act as NetBackup clients.
NDMP and NetBackup Hosts as Clients of Each Other
Network
NetBackup for NDMP server This is a NetBackup master or media server with NetBackup for NDMP installed. The NetBackup for NDMP server acts as an NDMP client.
NDMP Host
NDMP Host
NDMP hosts act as NetBackup clients ... NOTE: NetBackup software is NOT installed on NDMP hosts.
Types of NDMP Backup

The NDMP server application on the NDMP host performs backups and restores of the NDMP host, directed by commands received from an NDMP client (NetBackup). Backups can be conducted in any of the following ways:

NDMP local backup NDMP three-way backup Backup to a Media Manager device on the NetBackup server
NDMP Local Backup

The NetBackup for NDMP server initiates the backup. The data travels from the NDMP hosts disk to a storage device attached to the same host, or to a device available on a SAN.
NDMP Local Backup/Restore
LAN/WAN NDMP host
NetBackup for NDMP server
FC/SAN Disks Tape library
Storage devices on SAN
Local NDMP backup Data travels from disk to tape on same NDMP host, or from disk to tape device on SAN. Backup data is NOT sent over local network. The tape drives must be in NDMP-type storage units.
NDMP Three-Way Backup

The NetBackup for NDMP server initiates the backup. The data travels over the network, from an NDMP host to a storage device that is attached to another NDMP host on the local network or available on a SAN.
NDMP Three-Way Backup/Restore
LAN/WAN NDMP host NDMP Host
NetBackup for NDMP server
Disks Three-Way NDMP backup
Tape library
Data travels from disk on an NDMP host to tape device on another NDMP host. Backup data is sent over the local network. The tape drives must be in NDMP-type storage units.
Backup to Media Manager Storage Devices (Remote NDMP)

The data travels over the network from an NDMP host to a Media Manager-type storage device attached to a NetBackup media server or available on the SAN.
NDMP Backup to a Media Manager Device (Remote NDMP)
LAN / WAN NetBackup for NDMP server NDMP host
FC/SAN
Storage Devices on SAN
Tape library
Disks
To NetBackup Server-Attached Media Manager Storage Units Data travels from NDMP host to a drive on a NetBackup media server or on a SAN. Backup data is sent over the local network. NOTE: The NetBackup drive(s) must be in Media Manager type storage units.
NDMP Policies
NDMP Policies
After installing and configuring NetBackup for NDMP, you can schedule backups by creating an NDMP policy in NetBackup. An NDMP policy can have one or more NetBackup clients. Each NetBackup client must be an NDMP host (see figure NDMP and NetBackup Hosts as Clients of Each Other on page 6). Note that you do not install any NetBackup software on the NDMP hosts. The allowable backup types for schedules in an NDMP policy are: Full, Cumulative Incremental, or Differential Incremental. User initiated backups and archives are not allowed, because the NDMP protocol does not permit these tasks. Restores of NDMP host backups can be initiated from any NetBackup media server that is within the same overall NetBackup storage domain and uses the same NetBackup master server as used by the media server that performed the backup. The data can be restored to the NDMP host where it was backed up, or to another NDMP host. NDMP policies can use either NDMP storage units or Media Manager storage units.
10
Storage Units
Storage Units
NetBackup uses either NDMP-type storage units (for local or three-way backup), or Media Manager storage units (for backup to devices attached to a NetBackup media server).
NDMP Storage Units

When backing up NDMP host data to devices attached to an NDMP host or available to the NDMP host on a SAN, NetBackup requires NDMP-type storage units. An NDMP storage unit can contain standalone or robotic drives. Robotic controls can be in a TLD (Tape Library DLT), TL8 (Tape Library 8MM), TLH (Tape Library Half Inch), or ACS robot type.
Media Manager Storage Units

When backing up NDMP host data to devices attached to a NetBackup for NDMP server or available to the server on a SAN, you can use drives configured in Media Manager-type storage units. For NDMP backup, drives in Media Manager-type storage units do not have to be dedicated to NDMP data: they can store backups of regular (non-NDMP) NetBackup clients as well as of NDMP clients. Refer to the Configuring NDMP Backup to NetBackup Media Servers chapter for configuration help.
Assigning Tape Drives to Different Hosts

Robotic tape drives can be divided up among NDMP hosts and NetBackup servers. For example, referring to the NDMP and Non-NDMP Storage Units diagram:
Tape drives 1, 3, and 5 are attached to NDMP hosts and are in NDMP storage units that can be used for NDMP backup (local or three-way). The commands that control these drives originate on the NetBackup for NDMP server and are sent through the NDMP connection on the network. The NDMP server application on each NDMP host translates the NDMP commands into SCSI commands for the local drives.
Tape drives 2 and 4 are attached to a NetBackup server and are in non-NDMP storage units, controlled in the same way as other drives on NetBackup servers. Depending on the type of storage unit, these drives can be used for the following:
For non-NDMP clients of NetBackup

11
Storage Units
In the case of tape drives in Media Manager storage units, they can be used for both NDMP (local or three-way) and non-NDMP backup.
In this diagram, all tape drives except drive 4 can be used for NDMP backup.
NDMP and Non-NDMP Storage Units
LAN/WAN
Drive-control commands for NDMP
NB for NDMP media server
NDMP host
NDMP host
NDMP host
# +
Drive 1
#
Drive 2 Drive 3
Drive 5
Drive 4 TLD Robot
# In NDMP storage
unit
+ In NetBackup
Media Manager storage unit
Drives 1, 3, and 5 (in NDMP storage units) can be used for NDMP backups. Drive 2 (in Media Manager storage unit) can be used for NDMP or non-NDMP backup. Drive 4 (in different type of NetBackup storage unit) cannot be used for NDMP backup.
* In another type of
NetBackup storage unit (not NDMP or Media Manager)
12
Storage Units
Robotics control can be attached to an NDMP host or to a NetBackup server, as follows. NDMP host Commands are sent by NetBackup over the network to the NDMP host, which in turn sends them to the robot.
Robotics Control Attached to an NDMP Host
Commands to control robot NetBackup for NDMP Server NDMP Host
Robotic Control Robot
NetBackup server The robot is controlled in the same way as other robots on NetBackup servers.
Robotics Control Attached to a NetBackup Server
NetBackup Server
NDMP Host
Commands to control robot Robotic Control Robot
13
NDMP Backup Process
NDMP Backup Process

The following diagram (NetBackup Backup Processes.) shows the NetBackup processes that are involved in NDMP backups. During a backup, the following events occur: 1. From the EMM database, NetBackup obtains a media ID for the tape that will be used for the backup and sends a tape-mount request to ltid. 2. ltid on the NetBackup for NDMP server sends the NDMP (SCSI robotic) commands necessary to get the requested tape mounted on the storage device. 3. NetBackup sends the NDMP commands necessary to have the NDMP server application perform a backup to the tape. The backup data travels in one of two ways:

Between the local disk and tape drives on an NDMP host. Over the network, from an NDMP host without its own storage device to a NDMP host (or NetBackup media server) with a locally attached storage device (three-way backup).
4. The NDMP server application sends information to the NetBackup for NDMP server about the files that were backed up. This information is stored in the NetBackup file database. 5. The NDMP server application sends status about the backup operation to the NetBackup for NDMP server.
14
NDMP Backup Process NetBackup Backup Processes.
NetBackup Master Server Configuration Database File Database
NetBackup Administration Console bprd
bpdbm
nbproxy
nbpem
nbproxy EMM database nbemm nbrb nbjm
g lo ta Ca
NetBackup Master or Media Server This server has NetBackup for NDMP
bpcd
pe Ta
t es qu e R
n io at rm fo in
bpbrm Network Connection ndmpagent
bptm
3-way NDMP Host NDMP Server OS Tape Disk Local Disk NDMP Host NDMP Server OS
ltid
15
NDMP Restore Process
NDMP Restore Process

Because of the design of the NDMP protocol, only an administrator on a NetBackup server (master or media) can restore files from NDMP backups. During a restore, the administrator browses the file catalog and selects files from NDMP images in the same manner as for standard backup images. NetBackup Restore Processes shows the NetBackup processes involved in NDMP restores. The following events occur during a restore: 1. The NetBackup for NDMP server looks in its EMM database for the tape that contains the backup, and asks ltid to mount that tape. 2. ltid on the NetBackup for NDMP server sends the NDMP commands necessary to get the requested tape loaded on the storage device. 3. NetBackup sends the NDMP commands necessary to have the NDMP server application perform a restore operation to the disk. The restore data travels in one of two ways:

From a tape drive to a local disk (tape drive and disk are on the same NDMP host) Over the network, from an NDMP host (or NetBackup media server) with a locally attached storage device to another NDMP host (three-way backup/restore)
4. The NDMP server application sends status about the restore operation to the NetBackup for NDMP server.
16
NDMP Restore Process NetBackup Restore Processes NetBackup Master Server
Backup, Archive, and Restore (on master or media server)
bprd is on the master server
bprd
NetBackup Master or Media Server This server has NetBackup for NDMP.
bpcd
bpbrm
EMM database
NetBackup Media ID bptm

R est equ
Network Connection ndmpagent
e Tap
3-way NDMP Host NDMP Server OS NDMP Host NDMP Server OS
ltid
Disk Tape Local
Disk
17
Direct Access Recovery (DAR)
Direct Access Recovery (DAR)

Quickly restoring a single file or group of files from a backup image created by NetBackup for NDMP can be accomplished automatically using Direct Access Recovery (DAR). DAR can greatly reduce the time it takes to restore files. DAR is enabled by default (no configuration required). There are two prerequisites for using DAR with NetBackup for NDMP:

DAR must be supported by the NDMP host where the NDMP server application resides. The backup must have been made by NetBackup 4.5 GA or later, with the catalog in binary format (binary format is the default).
Note File-level DAR is supported; directory-level DAR is not supported. DAR enables the NDMP host to position the tape to the exact location of the requested file(s), reading only the data needed for those files. NetBackup automatically determines whether DAR will shorten the duration of the restore, and activates DAR only when it will result in a faster restore. NetBackup DAR can be disabled for all NDMP policies (see Enabling/Disabling DAR on page 40).
18
Installing NetBackup for NDMP
This chapter explains how to install the NetBackup for NDMP application on NetBackup servers.
Installation Notes

The NetBackup for NDMP master/media server must be running NetBackup 6.0 or later. The NetBackup for NDMP 6.0 software supports Solaris, HP-UX, Red Hat Linux, AIX, and Windows 2000/2003 (including 64-bit) master or media servers. For a detailed list of NAS platforms supported by NetBackup for NDMP, refer to NetBackup for NDMP Information on the Web on page x.
For making snapshots of NDMP (NAS) hosts, NetBackup Advanced Client software must be installed on the NetBackup master server, and on the clients that are used to perform backups. For more information, refer to the NetBackup Advanced Client System Administrators Guide. Drives and robots attached to the NDMP host must be types supported by the NDMP host and NetBackup. See NDMP Storage Units on page 11 for a list of supported robot types. For more information on storage devices, see the NetBackup Media Manager System Administrators Guide (UNIX or Windows). For notes and tips on your particular NDMP host, refer to NetBackup for NDMP Information on the Web on page x.
19
Installing on UNIX Servers
Installing on UNIX Servers

Note If you are installing in a cluster environment, you must freeze the active node before you begin the installation process so that migrations do not occur during installation. For information about freezing a service group, see the clustering section in the NetBackup High Availability System Administrators Guide for the cluster software you are running. On the UNIX host that you want to be the NetBackup for NDMP server, do the following: 1. Log in as root. 2. Install NetBackup server and client software as explained in the NetBackup Installation Guide for UNIX. 3. Make sure a valid license key for NetBackup for NDMP has been registered by entering the following command to list and add keys:
/usr/openv/netbackup/bin/admincmd/get_license_key
4. Insert the CD-ROM containing NetBackup for NDMP software in the drive. 5. Change your working directory to the CD-ROM directory:
cd /cd_rom_directory
Where cd_rom_directory is the path to the directory where you can access the CD-ROM. On some platforms, it may be necessary to mount this directory. 6. To install NetBackup for NDMP, execute the following:
./install
Since other NetBackup products are included on the CD-ROM, a menu appears. 7. Select NetBackup Add-On Product Software. a. Select the NetBackup for NDMP option. b. Enter q to quit the menu. c. When asked if the list is correct, answer y. 8. If this NetBackup for NDMP server is not your master server, also install your NDMP license key on the master. 9. In a clustered environment, the above steps must be done on each node in the cluster.
20
Installing on Windows Servers
Note If you are installing in a cluster environment, unfreeze the active node after the installation completes. For information about unfreezing a service group, see the clustering section in the NetBackup High Availability System Administrators Guide for the cluster software you are running
Installing on Windows Servers

Note If you are installing in a cluster environment, you must first freeze the active node so that migrations do not occur during installation. For information about freezing a service group, see the clustering section in the NetBackup High Availability System Administrators Guide for the cluster software you are running. On the Windows host that you want to be the NetBackup for NDMP server, perform the following: 1. Log in. 2. Install NetBackup server and client software as explained in the NetBackup Installation Guide for Windows. 3. NetBackup for NDMP is part of the core NetBackup product. Make sure a valid license key for NetBackup for NDMP has been registered by doing the following to list and add keys: a. From the NetBackup Administration window, choose Help. b. From the Help menu, select License Keys .... The NetBackup License Keys window appears. Existing keys are listed in the lower part of the window. c. To register a new key, click the star icon to open the Add a new License Key dialog. Type the new license key in the New license key field and click Add. The new license key appears in the lower part of the dialog box. 4. If this NetBackup for NDMP server is not your master server, install your NDMP license key on the master. 5. In a clustered environment, the above steps must be done on each node in the cluster.
Chapter 2, Installing NetBackup for NDMP
21
Uninstalling NetBackup for NDMP
Note If you are installing in a cluster environment, unfreeze the active node after the installation completes. For information about unfreezing a service group, see the clustering section in the NetBackup High Availability System Administrators Guide for the cluster software you are running
Uninstalling NetBackup for NDMP

On the server where you initially loaded the NetBackup for NDMP software, do the following. This procedure results in total removal of the NetBackup for NDMP software. Note In a cluster environment, you must first freeze the active node so that migrations do not occur during installation. For help freezing a service group, see the clustering section in the NetBackup High Availability System Administrators Guide for the cluster software you are running. 1. Check the Activity Monitor in the Administration Console to make sure no NetBackup for NDMP backups are active or running (State field reads Done). 2. If ltid is running, stop it (use the Activity Monitor > Daemons tab). 3. Pre-6.0 NetBackup on Solaris only: if ndmpmoveragent is running (check the Activity Monitor > Processes tab), stop it by entering the following:
cd /usr/openv/volmgr/bin ./ndmpmoveragent.stop
4. To remove the NetBackup for NDMP package, enter the following: On Solaris:
pkgrm VRTSnbdmp
On other UNIX platforms:

rm rm rm rm rm -f -f -f -f -f /usr/openv/lib/libndmp_bpfsmap.s? /usr/openv/lib/libndmpclient.s? /usr/openv/volmgr/bin/set_ndmp_attr /usr/openv/share/version_ndmp /usr/openv/netbackup/bin/ndmpmoveragent
where ? is a wildcard. 5. Restart ltid. Note If uninstalling in a cluster environment, unfreeze the active node after the uninstall.
22
Configuring NDMP Backup to NDMP-Attached Devices

This chapter explains how to configure backups on storage devices attached to NDMP hosts. Only NDMP-specific steps are described.
Note As an alternative to the device configuration procedures in this chapter, you can use the NetBackup Device Configuration wizard to discover and configure robots and drives that are attached to an NDMP host (requires NDMP protocol versions V3 or V4). To configure and use the NAS_Snapshot method when backing up NDMP host data, see the NetBackup Advanced Client System Administrators Guide. The following topics are covered in this chapter:

Authorizing Access to the NDMP Host Media Manager Device Configuration Verifying NDMP Password and/or Robot Connection Adding NDMP Storage Units Creating an NDMP Policy Enabling/Disabling DAR Setting Up Clustering Testing an NDMP Configuration
23
Authorizing Access to the NDMP Host

Before NetBackup can carry out backups, it must have access to the NDMP host. To authorize this access, use the following dialog from the NetBackup Administration Console on your NetBackup for NDMP master server. You can also use the NetBackup Device Configuration wizard to create this authorization. Note Do the following on the master server (not media server) if you are going to create snapshots using the Advanced Client NAS_Snapshot method.
To authorize NetBackup access to the NDMP host (from Administration Console) 1. On the NetBackup server: under Media and Device Management > Devices, click on NDMP Hosts. Under Actions, choose New > NDMP Host. The NDMP host name dialog appears.
2. Enter the name of the NDMP server that NetBackup will back up. Note This NDMP host name is case-sensitive. Whenever this host name is used (such as when configuring tape drives and storage units for this host), the name must be identical to the name entered here. 3. Click OK. The New NDMP Host dialog appears.
24
The term credentials refers to the username and password that NetBackup will use to access the NDMP host.
Use the global NDMP login.
Create a login to this NDMP host for all NetBackup servers.
Specify different NDMP logins for particular NetBackup servers.
4. Specify the following: Use gobal NDMP credentials for this NDMP host Select this option to enable all NetBackup media servers under the master server to access this NDMP host using a pre-defined global NDMP login. This login is created under Host Properties > Master Server > Properties > NDMP, on the NDMP Global Credentials dialog. Use the following credentials for this NDMP host on all media servers Select this option to enable all NetBackup media servers connected to the NDMP host to access the NDMP host using the login you specify on this dialog:
Username: the user name under which NetBackup will access the NDMP server. This user must have permission to execute NDMP commands.
Chapter 3, Configuring NDMP Backup to NDMP-Attached Devices
25
Note To see if your NDMP host vendor requires a particular username or access level (such as root), refer to NetBackup for NDMP Information on the Web on page x.
Password and Confirm Password: enter the password for this user.
Use different credentials for this NDMP host on each media server Select this option to specify NDMP logins for particular NetBackup servers, then click Advanced Configuration. The Advanced NDMP Credentials dialog appears.
5. Click Add. The Add Credentials dialog appears.
26
6. Select a NetBackup server and specify the username and password it will use to access the NDMP host. 7. Click OK. NetBackup validates the username and password. The NetBackup server and username appear in the Advanced NDMP Credentials dialog. 8. If needed, click Add again to specify other servers and user names. 9. Repeat this procedure for each NDMP host that NetBackup will back up.
Access for Three-Way Backups and NDMP to Media Manager

To perform three-way backups, you must authorize access to the desired NDMP host as described in the previous section.

Three-way backups: for the NDMP host name, specify the NDMP host that has no attached tape drive. NDMP to Media Manager backups: for the NDMP host name, specify the NDMP host that will be backed up to the media manager storage unit defined on the NetBackup server. See the chapter titled Configuring NDMP Backup to NetBackup Media Servers for more information.
27
Media Manager Device Configuration

On the NetBackup for NDMP server, use Media and Device Management in the Administration Console to add drives and robots. As an alternative, you can use the NetBackup Device Configuration wizard. The following procedures and examples treat NDMP configuration issues only. See the NetBackup Media Manager System Administrators Guide for general information on configuring NetBackup media. For more information on configuring storage devices for specific NDMP hosts, refer to NetBackup for NDMP Information on the Web on page x. Note These procedures do not apply to setting up devices attached to the NetBackup media server. To back up NDMP data to Media Manager devices (remote NDMP), storage units are configured in the same way as ordinary NetBackup (non-NDMP) devices. For details, refer to Configuring NDMP Backup to NetBackup Media Servers on page 45, and to the NetBackup Media Manager System Administrators Guide.
Adding a Robot Directly Attached to an NDMP Host

Using the NetBackup Administration Console: 1. Start the NetBackup Administration Console on the NetBackup for NDMP server as follows: On Windows: from the Windows Start menu, select Programs, VERITAS NetBackup, NetBackup Administration Console. On UNIX, enter the following:
/usr/openv/netbackup/bin/jnbSA &
2. Select Media and Device Management > Devices in the left pane. 3. On the Actions menu, select New, then select Robot... from the popup. The Add Robot dialog appears.
28
Explained in online help or in the Media Manager System Administrators Guide.
Explained in the following steps.
For assistance with the Add Robot dialog, refer to the online help or to the NetBackup Media Manager System Administrators Guide. The steps below explain the portions that are unique to configuring NetBackup for NDMP. 4. For Media Manager host, specify the host that manages the EMM database (by default, this is the NetBackup master server). 5. For Device host, use the pull-down to select the NetBackup media server. 6. Specify Robot type and number as explained in the NetBackup Media Manager System Administrators Guide. 7. Under Robot control, click Robot control is attached to an NDMP host.
29
8. For Robot device path, enter the device name of the robot. There is no need to include the NDMP host name as part of the device path. To determine the device name of the robot, refer to NetBackup for NDMP Information on the Web on page x for information pertaining to your NDMP host. 9. For NDMP host name, enter the name of the NDMP host to which the robot is attached. 10. Specify the Bus, Target, and LUN values if they are required by the NDMP host. Refer to NetBackup for NDMP Information on the Web on page x for information pertaining to your NDMP host. By default, the bus, target and lun values are 0. 11. Click OK. A popup message asks if you want to stop and restart the device manager service (or daemon). Click Yes.
30
Adding a Drive
Using the NetBackup Administration Console: 1. Select Media and Device Management > Devices in the left pane. 2. On the Actions menu, select New, then select New Drive (on UNIX, Tape Drive) from the popup. The Add Drive dialog appears.
3. For Drive Name: Enter the name of the drive. 4. For Host and path information: a. Click Add to specify a drive path.
31
The Add Path dialog appears:
b. For Device host, select the name of the NetBackup media server. Use the pull-down to select media servers already defined, or click Add to enter a new one. c. For Path (called No rewind device on UNIX), enter the device file name of the tape drive, such as nrst2a. Refer to the NAS vendor documentation for your drive for the correct format of the device file name. As an alternative, you can use the following command to find the device file name for the drive, if the NDMP host is running NDMP protocol V3 or later:
tpautoconf -probe ndmp_host_name
d. Click This path is for a Network Attached Storage device. e. For NDMP Host, use the drop-down to select the name of the NAS filer to which the drive is attached. f. When finished, click OK.
5. Back on the Add a New Drive dialog, enter the Drive information as required. 6. Repeat this procedure for each drive that must be added. When asked whether or not to restart the Media Manager device daemon and all robotic daemons, click Yes.
32
Checking a Media Manager Configuration

On the NetBackup for NDMP server, do the following:
On UNIX, execute /usr/openv/volmgr/bin/vmps and verify that ltid, vmd, avrd, and any required robotic daemons are active. On Windows, go to the NetBackup Administration Console and use the Activity Monitor (Processes tab) to verify that the above processes are active. From the NetBackup Administration Console, use the Device Monitor to ensure that the drive is in the UP state.
Adding Volumes to a Media Manager Configuration

Use the NetBackup Media and Device Management utility to add the volumes that you will be using for the NDMP host backups. See the Media Manager System Administrators Guide for instructions. Note When specifying the Robot Control Host for a volume that will be in a robot, specify the host name for the NetBackup for NDMP server, not the NDMP host.
33
Verifying NDMP Password and/or Robot Connection
Verifying NDMP Password and/or Robot Connection

When you authorize NetBackup access to the NDMP host and configure robots using the Administration Console, NetBackup automatically verifies your NDMP credentials and the robotic configuration. If desired, you can re-verify them. For example:
tpautoconf -verify ndmp_host_name
A successful verification looks like the following:

Connecting to host "stripes" as user "root"... Waiting for connect notification message... Opening session--attempting with NDMP protocol version 4... Opening session--successful with NDMP protocol version 4 host supports MD5 authentication Getting MD5 challenge from host... Logging in using MD5 method... Host info is: host name "stripes" os type "NetApp" os version "NetApp Release 7.0.0.1" host id "0033625811" Login was successful Host supports LOCAL backup/restore Host supports 3-way backup/restore
34
Adding NDMP Storage Units

On the NetBackup master server, add an NDMP-type storage unit for the devices that will contain the backup data. Most of the requirements are the same as for adding a Media Manager storage unit. The following topics explain the differences when adding an NDMP storage unit. See the NetBackup System Administrators Guide for more information. Note NDMP-type storage units are not used for backups to media server-attached devices. Use Media Manager storage units, not NDMP-type units. Refer to the Configuring NDMP Backup to NetBackup Media Servers chapter for details. 1. In the NetBackup Administration Console, select NetBackup Management > Storage Units. 2. On the Actions menu, select New > Storage Unit. The New Storage Unit dialog appears.
35
3. For Storage unit name, enter a unique name for the storage unit. 4. For Storage unit type, select NDMP. 5. For On demand only: this specifies whether the storage unit is available only when a policy or schedule specifically requests it. If this option is not used, the storage unit is available to any NDMP policy or schedule. 6. For Storage device, select the type of device for this storage unit. 7. For NDMP host, specify the NDMP host where the tape drive is physically attached. The remaining fields are described in the NetBackup System Administrators Guide.
36
Creating an NDMP Policy

On the NetBackup master server, create an NDMP policy to configure backups of the NDMP host. Note You can use the Backup Policy Configuration wizard to create NDMP policies. Creating an NDMP policy is very similar to creating other NetBackup policy types. The following topics explain the differences when creating NDMP policies. See the NetBackup System Administrators Guide for more information on NetBackup policies and the Policy utility. Note To configure a policy for the NAS_Snapshot method and SnapVault, see the NetBackup Advanced Client System Administrators Guide.
Attributes
Specify the following policy attributes:

Policy Type: NDMP Policy Storage Unit:

If the NDMP host has more than one storage unit and you want to direct backups for this policy to a specific storage unit, specify the name of that storage unit. For a three-way backup, specify a storage unit that was defined for the target NDMP host with attached tape. For NDMP backup to Media Manager devices, specify a Media Manager storage unit defined for a device connected to a NetBackup media server (see the Configuring NDMP Backup to NetBackup Media Servers chapter).
Clients
In the client list, specify the following for each client in an NDMP policy:
Hostname Name of the NDMP host
Hardware and operating system NDMP NDMP
37
Files
The Backup Selections list must specify directories from the perspective of the NDMP host. Two examples:
/home/dir1/ /vol1
The following Backup Selections capabilities are NOT supported for an NDMP policy:

Wildcards in pathnames. For example, /home/* is an invalid entry. Individual file names. Only directory or volume names are allowed. Exclude list (because client software is not installed on the NDMP host). You can, however, exclude files by using the SET keyword as shown under Using Environment Variables in Backup Selections list. The SET option allows you to exclude files on a backup. The format is vendor dependent; refer to the vendors documentation for more details on which variable can be passed and in what format.
Schedules
You can specify any of the following backup types in a schedule for an NDMP policy:

Full Cumulative Incremental Differential Incremental
Specify Override policy storage unit only if this client of NetBackup (the NDMP host) has more than one storage unit and you want to use a specific storage unit for this schedule. In this case, the client must be the only client in this NDMP policy.
Using Environment Variables in Backup Selections list

NDMP allows you to use environment variables to pass configuration parameters to an NDMP host with each backup. NDMP environment variables can be one of the following types.
Defined as optional by the NDMP protocol specification. You can set these variables.
Specific to an NDMP host vendor. You can set these variables.
Reserved for use by NetBackup:
38
FILESYSTEM LEVEL DIRECT EXTRACT ACL_START In NetBackup, environment variables can be set within the Backup Selections list by specifying one or more SET directives. Note In the Backup Selections list, the SET directive must be the first in the list, followed by the file systems or volumes to back up. To obtain up-to-date information on environment variables relating to particular NAS vendors, refer to NetBackup for NDMP Information on the Web on page x. In general, the syntax of a SET directive is as follows:
SET variable = value
Where variable is the name of the environment variable and value is the value that is assigned to it. The value can be enclosed in single or double quotes, and must be enclosed in quotes if it contains a space character. For example:
SET ABC = 22 SET DEF = "hello there" SET type = tar
Setting a variable equal to no value unsets that variable. For example:

SET ABC =
Variables accumulate as the Backup Selections list is processed. For example, if Backup Selections contains the following entries:
/vol/vol1 SET HIST = N /vol/vol2 SET DEF = 20 SET SAMPLE = all /vol/vol3
Directory/vol/vol1 will be backed up without any user-specified environment variables. The second directory (/vol/vol2) will be backed up with the variable HIST set to N. The third directory (/vol/vol3) will be backed up with all three of the environment variables set. If an environment variable appears again later in the list, the value of this variable overrides the previous value of the variable.
39
Enabling/Disabling DAR
The values used in each backup are saved and provided to subsequent restores of the directory. The NDMP host may have environment variables that are set internally and these are also saved for restores.
By default, NetBackup for NDMP is configured to use Direct Access Recovery (DAR). For each restore, NetBackup automatically determines if the use of DAR will speed up the restore. NetBackup uses DAR only when it will result in a faster restore. Note NetBackup can use DAR only if the NDMP NAS host supports it (contact your NAS vendor for details). DAR can be turned off if desired. This may be necessary if you are having problems with DAR and your NDMP host is an older machine or is not running the latest NAS OS version. 1. In the NetBackup Administration Console, expand Host Properties and click on Master Servers or Media Servers. 2. Right-click on the name of the server and select Properties. 3. Click on General Server.
40
This is the UNIX version of the Properties dialog, General Server:
41
This is the Windows version of the Properties dialog, General Server:
4. Uncheck the Use direct access recovery for NDMP restores box, and click Apply. This disables DAR on all NDMP restores.
42
Setting Up Clustering
Setting Up Clustering
Before configuring NetBackup for NDMP for clustering, the following must be installed on each node of the cluster:

NetBackup server (see the NetBackup Installation Guide). NetBackup for NDMP software (see Installing NetBackup for NDMP on page 19 of this manual). Note that for Windows servers, only the NetBackup for NDMP licence key has to be installed.
1. Configure NDMP-attached robots and drives, and then storage units and policies, just as you would in a normal, non-clustered environment:
You can use the Device Configuration wizard, or configure devices manually as described under Authorizing Access to the NDMP Host on page 24 and following. To use the same robotic libraries throughout a cluster, robot numbers must be consistent. The Device Configuration wizard attempts to ensure this configuration. If you are configuring robots manually as described in this guide, be sure to use the same robot number for a given robot, from one host to another in the cluster.
2. When finished configuring devices and policies for NetBackup for NDMP, fail-over to the next node in the cluster and configure the drives and robots.
Select the same robot number that you used when configuring the robot for the first node.
Post-Installation Changes
After NetBackup has been configured in a clustered environment, most configuration information is available to all nodes in the cluster, by means of a shared hard drive. However, changes made in the Host Properties area of the Administration Console are not available on the shared drive. Such changes apply only to the active node. Host Properties changes made on the active node must be manually duplicated on each node, if NetBackup is to perform exactly the same way in case of failover to another node. Refer to the NetBackup High Availability Guide for assistance.
43
Testing an NDMP Configuration
Testing an NDMP Configuration

To test the configuration, run the backup and then restore some files. For instructions, see the following topics:

Performing an NDMP Backup on page 56. Performing a Restore from the Server on page 57.
If you encounter problems, see Troubleshooting on page 59.
44
Configuring NDMP Backup to NetBackup Media Servers
This chapter describes how to configure NetBackup for NDMP to make backups to Media Manager storage units (remote NDMP). Only NDMP-specific steps are described. The following topics are covered in this chapter:

Overview Configuring NDMP Backup to Media Manager Devices
45
Overview
Overview
Using a feature known as remote NDMP, you can back up NDMP data to a drive configured in a Media Manager storage unit on a NetBackup media server. The drive can be used for both NDMP backups and for non-NDMP backups. See the following diagram. NDMP Backup to a Media Manager Storage Unit
LAN / WAN
NetBackup for NDMP server NDMP hosts (NAS filers). . .
NetBackup drives in Media Manager storage unit(s).
Data travels between NDMP hosts and a drive on a NetBackup media server. NOTE: The NetBackup media manager drive(s) need not be dedicated to NDMP backups: they can be used for non-NDMP backups as well.
46
Configuring NDMP Backup to Media Manager Devices

These are the basic steps to configure NDMP backups to Media Manager storage units. 1. Authorize the NetBackup server to access the NDMP hosts you want to back up. Note Do the following on the master server (not media server) if you are going to create snapshots using the Advanced Client NAS_Snapshot method. a. Under Media and Device Management > Devices, click on NDMP Hosts. Under Actions, choose New > NDMP Host to display the NDMP Host dialog. b. Fill in the values as described under Authorizing Access to the NDMP Host on page 24. c. Repeat the above for each NDMP host that the NetBackup server will back up. 2. Use the NetBackup Device Configuration wizard to configure the drive(s) and robot(s). Note Do not use the device configuration procedure in the Configuring NDMP Backup to NDMP-Attached Devices chapter in this guide. Rather, configure the robots and drives in the same way as ordinary Media Manager devices, described in the NetBackup Media Manager System Administrators Guide. Note Drives can be shared using the Shared Storage Option (SSO) of NetBackup. For an overview of the setup procedure, see Using The Shared Storage Option (SSO) on page 49. The drives can be shared as both NDMP drives and non NDMP drives. 3. Create a Media Manager-type storage unit for the drive(s). For details on storage units, refer to the NetBackup System Administrators Guide, Volume I. Note The storage unit type must be Media Manager, not NDMP. 4. Create an NDMP-type policy. On the New/Change Policy display, be sure to specify the storage unit created at step 3. See Creating an NDMP Policy on page 37.
Chapter 4, Configuring NDMP Backup to NetBackup Media Servers
47
48
Using The Shared Storage Option (SSO)
This chapter describes the steps for setting up the Shared Storage Option with NetBackup for NDMP. The following topics are covered in this chapter:

Shared Storage Option (SSO): Basic Diagram Setting up SSO: Overview Using the Device Configuration Wizard
49
Shared Storage Option (SSO): Basic Diagram
Shared Storage Option (SSO): Basic Diagram

The following figure shows a robotic library on a SAN that can share its drives between two NetBackup for NDMP servers and two NDMP hosts. Drive sharing requires a license for the Shared Storage Option. (A SAN is not required.)
NDMP Backup Using Shared Storage Option
LAN NetBackup for NDMP server 1 NetBackup for NDMP server 2 NDMP host NDMP host
Fibre Channel SAN (optional)
Drives in the tape library are shared by NetBackup servers 1 and 2 for backing up NDMP hosts. Drives can be in Media Manager storage units or NDMP storage units, or both.
For each robot, robotic control can be handled by either a NetBackup media sever or an NDMP server (not both).
50
Setting up SSO: Overview
Setting up SSO: Overview

This is an outline of the steps for setting up access to a robotic drive shared between NDMP and NetBackup servers. For a more complete discussion of SSO, refer to the Shared Storage Option (SSO) Topics chapter in the NetBackup Media Manager System Administrators Guide. This procedure assumes the following:

That the requirements for SSO have been met, as described in the NetBackup Media Manager System Administrators Guide. That all physical devices, including the NDMP host, are correctly connected to the network. That the NDMP host is supported by NetBackup for NDMP. For a document that lists supported NAS systems, see NetBackup for NDMP Information on the Web on page x.
1. Configure NetBackup access to the NDMP host. For details, see Authorizing Access to the NDMP Host on page 24. 2. Verify that the NDMP host can access the required robots and drives. To verify NDMP host access to the required devices, run the following commands on a NetBackup media server that is authorized to access the NDMP host:
tpautoconf -verify ndmp_host_name tpautoconf -probe ndmp_host_name
The -verify option verifies that the NetBackup server can access the NDMP host; the -probe option lists the devices that are visible to the NDMP host. 3. From the NetBackup Administration Console, use the Device Configuration Wizard to configure the devices and storage units. See Using the Device Configuration Wizard on page 52. Note An NDMP storage unit must be defined for each NDMP host that will be sharing a drive. If all hosts have access to the shared drive(s), the Device Configuration Wizard can create these storage units automatically.
Chapter 5, Using The Shared Storage Option (SSO)
51
Using the Device Configuration Wizard

The most convenient way to configure devices and storage units for NDMP hosts (with or without the SSO option) is to use the Device Configuration Wizard. 1. In the NetBackup Administration Console, click Configure Storage Devices to launch the Device Configuration Wizard. 2. Click Next on the Welcome screen. The Device Hosts screen appears.
3. Under Device Hosts, place a check beside the NetBackup media server that will access the NDMP host, click on the server name to highlight it, and click Change.
52
The Change Device Host screen appears.
4. Place a check beside NDMP server and click OK. The Device Hosts screen re-appears. NDMP is now listed in the Optional Devices to be Scanned column for the media server (screen detail shown below).
5. On the Device Hosts screen, click Next to continue.
Chapter 5, Using The Shared Storage Option (SSO)
53
The NDMP Hosts screen appears, showing the NDMP host(s) on which you can configure devices.
6. On the NDMP Hosts screen, click Next to configure the NDMP-attached devices. 7. Follow the screens in the wizard to complete the configuration.
54
Backup and Restore Procedures
This chapter describes the procedures for backing up and restoring NDMP-type policies. For backup and restore of a NAS snapshot, refer to the NetBackup Advanced Client System Administrators Guide.

Performing an NDMP Backup Performing a Restore from the Server
55
Performing an NDMP Backup
Performing an NDMP Backup

Only the administrator can perform NDMP backups and restores on the NetBackup server (master or media). The NDMP protocol does not allow users to initiate a backup or restore, and there is no NetBackup client software installed on an NDMP host.
Automatic Backup of an NDMP Policy

To configure an NDMP policy and set up schedules for automatic, unattended backups, see Creating an NDMP Policy on page 37 and the NetBackup System Administrators Guide.
Manual Backup of an NDMP Policy

Only a NetBackup administrator can initiate an NDMP backup. The following procedure explains how to perform the backup using the NetBackup Administration Console. For further information on the NetBackup Administration Console, see the NetBackup System Administrators Guide (Windows or UNIX). 1. As administrator, start the NetBackup Administration Console on the NetBackup server as follows: On Windows: from the Windows Start menu, select Programs, VERITAS NetBackup, NetBackup Administration Console. On UNIX, enter the following:
/usr/openv/netbackup/bin/jnbSA &
2. Click on Policies. Right click on the NDMP policy name and select Manual Backup from the pop-up menu. This opens the Manual Backup dialog. 3. In the Manual Backup dialog, select a schedule, then select the clients (NDMP hosts) that you want to back up. If you do not select any schedules, NetBackup uses the schedule with the highest retention level. If you do not select any clients, NetBackup backs up all configured NDMP hosts. 4. Click OK to start the backup.
56
Performing a Restore from the Server

User-directed restores of files are not allowed, since there is no NetBackup client software installed on an NDMP host. The administrator can use the Backup, Archive, and Restore interface on a NetBackup server (master or media server) to restore files to the NDMP host from which they were backed up, or to a different NDMP host. For help with the basic restore procedure, see the NetBackup online help in the Administration Console, or the NetBackup Backup, Archive, and Restore Getting Started Guide. Note the following: In the Specify NetBackup Machines and Policy Type dialog, specify the following:
For the server, select the NetBackup master server. If your configuration has multiple master servers, specify the master server that has the policy for the NDMP host that you are restoring. If the server name is not in the pull-down, use Edit Server List to add it. For the source and destination clients, select the appropriate NDMP (NAS) hosts.
Note The destination host must be an NDMP host compatible with the data format of the source (the source and destination must be of the same NAS vendor type). Caution An NDMP restore always overwrites existing files. If the desired hosts are not available in the pull-down, use Edit Client List to add the client.
In the policy type field, select NDMP.
Chapter 6, Backup and Restore Procedures
57
58
Troubleshooting
The following information may be useful in troubleshooting NetBackup.

NDMP Operating Notes and Restrictions Troubleshooting NetBackup Troubleshooting Media Manager on Windows Systems Troubleshooting Media Manager on UNIX systems Troubleshooting DAR Testing a Robot
Note For explanations of NetBackup status codes, refer to the NetBackup Status Codes and Messages chapter in the NetBackup Troubleshooting Guide.
59
NDMP Operating Notes and Restrictions
NDMP Operating Notes and Restrictions

Before troubleshooting a suspected problem, review the following operating notes. To obtain troubleshooting information that may apply to particular NDMP hosts, refer to NetBackup for NDMP Information on the Web on page x.
A tape created on an NDMP storage unit is in backup format and cannot be restored from a non-NDMP storage unit. If you duplicate an NDMP backup image the new copy is still in backup format and cannot be used for restores on a non-NDMP storage unit. In the Backup Selections list for an NDMP policy, you can include only directory paths. Wildcards and individual file names are not allowed. You cannot back up files where the path length is greater than 1024 characters. The NDMP protocol uses port 10000 for communication. On UNIX systems, the NetBackup avrd process utilizes ICMP (Internet Control Message Protocol) to ping NDMP hosts to verify network connectivity. This protocol is required for the NetBackup for NDMP product. If backup or restore jobs are running slowly, verify that the network interface cards (NIC) are set to full duplex. Half duplex often causes poor performance. For assistance viewing and resetting duplex mode for a particular NAS host, consult the documentation provided by the manufacturer. You may be able to use the ifconfig (or ipconfig) command, as explained in the NetBackup Troubleshooting Guide.
Notes on DAR
DAR can be used when restoring backups that were made by NetBackup 4.5GA or later. Starting with NetBackup 4.5GA, NetBackup stores the required DAR offset information on each backup.
Note For backups made by pre-4.5GA versions of NetBackup, restores cannot use DAR, because the pre-4.5 versions did not store the DAR offset information.

DAR can be used when restoring files, but not when restoring directories. Backups must have been performed with the NetBackup catalog set to binary mode. For backups made with the catalog set to ASCII mode, restores cannot use DAR, because ASCII mode did not store the required DAR offset information on each backup. Note that all backups made prior to NetBackup 4.5 used ASCII catalog mode. To use DAR with NetBackup, the NDMP host you want to restore must support DAR. Some NDMP host vendors do not currently support DAR.
60
Troubleshooting NetBackup
Types of Logs
NetBackup uses two types of logging: unified logging, new in this 6.0 release, and legacy logging as used in previous releases. Both are described in the Using Logs and Reports chapter in the NetBackup Troubleshooting Guide. Note:

All unified logs are written to /usr/openv/logs (UNIX) or install_path\logs (Windows). Unlike legacy logging, there is no need to create logging directories. Use the vxlogview command to examine unified logs (see examples in the next section): On UNIX: /usr/openv/netbackup/bin/vxlogview On Windows: install_path\NetBackup\bin\vxlogview Refer to the NetBackup Troubleshooting Guide for assistance in using the vxlogview command. See also the vxlogview man page or the NetBackup Commands Guide.
Troubleshooting Steps

Check the NetBackup All Log Entries report for information about the failed job. To get more information about a problem, do the following:
In the NetBackup Administration Console: expand Host Properties in the left pane, click on Media Server, and right click on the server name in the right pane. From the pop-up, select Properties, then click Logging and set the Global logging level to 5. This increases logging detail to the highest level, for both unified logging and legacy logging. View the unified logging information in /usr/openv/logs (UNIX) or install_path\logs (Windows) for the following processes: ndmpagent (originator ID 134), ndmp (originator ID 151), nbpem (originator ID 116), nbjm (originator ID 117), and nbrb (originator ID 118). For ndmpagent logs, try the vxlogview command as follows:
/usr/openv/netbackup/bin/vxlogview -i ndmpagent -d T,s,x,p
For ndmp logs, try the vxlogview command as follows:

/usr/openv/netbackup/bin/vxlogview -i ndmp -d T,s,x,p
Chapter 7, Troubleshooting
61
On the NetBackup for NDMP server, create bptm, bpbrm, and ndmpagent legacy debug log folders in the /usr/openv/netbackup/logs directory (UNIX) or install_path\NetBackup\logs folder (Windows). NetBackup writes legacy log files in these directories, if the directories exist.
Note The legacy and unified logging files can consume a lot of disk space; delete the log files when you are finished troubleshooting and set logging to a lower level of detail.
To verify that the appropriate services are running, use either the NetBackup Activity Monitor, the Windows control panel (on Windows systems), or the bpps command (UNIX systems). If NDMP host backups terminate with a status code of 154 (storage unit characteristics mismatched to request), the problem may be one of the following:

Verify that the NetBackup configuration is correct. There may be a conflict between the policy type and storage unit type (for example, if the policy type is Standard and the storage unit is of type NDMP).
If your NDMP backup fails with a status code of 99 (NDMP backup failure), none of the paths in your NDMP policy Backup Selections list were backed up successfully. Check the NetBackup All Log Entries report for more information. A possible cause of this status is that none of the backup paths exist on the NDMP host.
NDMP Backup Levels

At the start of a debug log, you may see an entry titled LEVEL. This refers to an environment variable that was set by NetBackup based on the type of backup. Below is an example from a bptm log. For more information on environment variables, refer to Using Environment Variables in Backup Selections list on page 38.
08:48:38.816 [22923] <2> write_data_ndmp: values: 08:48:38.816 [22923] <2> write_data_ndmp: 08:48:38.816 [22923] <2> write_data_ndmp: FILESYSTEM=/vol/vol0/2million 08:48:38.817 [22923] <2> write_data_ndmp: PREFIX=/vol/vol0/2million 08:48:38.817 [22923] <2> write_data_ndmp: backup environment Environment 1: TYPE=dump Environment 2: Environment 3: Environment 4: LEVEL=0
The NDMP backup LEVEL is modeled after UNIX dump levels. The backup level is a number in the range of 0 to 9.
62
Troubleshooting Media Manager on Windows Systems
An NDMP backup level of 0 is a full backup. A backup level above 0 is an incremental backup of all objects modified since the last backup of a lower level. For example, level 1 is a backup of all objects modified since the full backup (level 0); level 3 is a backup of all objects modified since the last level 2 incremental.
NetBackup Backup Types and Corresponding NDMP Backup Levels NetBackup Backup Types NetBackup Full NetBackup Cumulative Incremental NetBackup Differential Incremental NDMP Backup Levels NDMP level 0 NDMP level 1 NDMP level (last level + 1, up to 9) never goes higher than 9
Troubleshooting Media Manager on Windows Systems

For legacy logging, enable debug logging by creating reqlib and daemon directories in the install_path\Volmgr\debug directory on the NetBackup for NDMP server. Check the Windows Event Viewer Application log for troubleshooting clues. For more information on the Event Viewer logging option, refer to the NetBackup Troubleshooting Guide. Use the Activity Monitor interface or the Windows control panel to verify that the Media Manager services are running. Drives can be unexpectedly set to the DOWN state due to communication problems between avrd on the NetBackup for NDMP server and the NDMP server application on the NDMP host. Some possible causes for the communication problems are:

Network cable on the NDMP host was unplugged. NIS (Network Information System) problems on the NetBackup for NDMP server (NDMP client). The NDMP host was halted for too long.
Note Whatever the cause, if the avrd connection to the NDMP host fails, the drive is set to DOWN and is not automatically set to UP when the communication problem is corrected.
63
Troubleshooting Media Manager on UNIX systems
Troubleshooting Media Manager on UNIX systems

Ensure that syslogd is logging Media Manager messages. For more information on syslogd, refer to the NetBackup Troubleshooting Guide. Start ltid with the -v option. Check the systems syslog for troubleshooting clues. Use vmps to make sure that the appropriate Media Manager daemons are running. Drives can be unexpectedly set to the DOWN state due to communication problems between avrd on the NetBackup for NDMP server and the NDMP server application on the NDMP host. For details, refer to the last main bullet and note under the Troubleshooting Media Manager on Windows Systems section.
Troubleshooting DAR
In certain situations, one of the following messages may appear in the unified logs for ndmpagent (originator ID 134) on the NetBackup media server. These are also written to the progress log. Message: DAR disabled - Number of paths n > DAR_MAXIMUM_FILE_LIST_COUNT x Explanation: The number of files being restored is greater than the maximum allowed (default is 1024). You can either select fewer files for the restore, or increase the DAR maximum Backup Selections list count. (Increasing the maximum is not supported by some NDMP host vendors.) To increase the DAR maximum Backup Selections list count, place a DAR_MAXIMUM_FILE_ LIST_COUNT x entry in the following file and specify x as a number greater than 1024. On UNIX:
/usr/openv/netbackup/db/config/ndmp.cfg
On Windows:
install_path\NetBackup\db\config\ndmp.cfg
Message: DAR disabled - not supported by NDMP host Explanation:
64
Troubleshooting DAR
The current NDMP host does not support DAR. Message: DAR disabled - unable to retrieve DAR info Explanation: DAR information is not available for the file. Message: DAR disabled - Backup performed prior to NB 4.5 Explanation: The DAR feature can be used when restoring backups that were made by NetBackup 4.5GA or later. Starting with NetBackup 4.5GA, NetBackup stores the required DAR offset information on each backup. For backups made by pre-4.5GA versions of NetBackup, restores cannot use DAR, because the pre-4.5 versions did not store the DAR offset information. Message: DAR disabled - NDMP host did not provide DAR info during backup Explanation: The backup was performed with an NDMP host version that does not support DAR. Ask the NDMP host vendor if a later NAS software version is available that supports DAR. Message: DAR disabled - Optimal DAR parameters exceeded for this image size Explanation: NetBackup determined that the restore would take longer with DAR than without it. Message: DAR disabled - Directory DAR not supported Explanation: DAR is automatically disabled when a restore job specifies a directory to restore. DAR can be used when restoring files, but not when restoring directories.
65
Troubleshooting DAR
Message: DAR disabled by DAR config file Explanation: DAR was disabled by adding the entry NDMP_DAR_DISABLED to the following file: On UNIX:
/usr/openv/netbackup/db/config/ndmp.cfg
On Windows:
install_path\NetBackup\db\config\ndmp.cfg
This method of disabling DAR is obsolete. Use the Host Properties dialog as explained under Enabling/Disabling DAR on page 40. Message: DAR disabled by host parameters Explanation: DAR was disabled on the Master or Media Server Properties dialog. To re-enable DAR, see Enabling/Disabling DAR on page 40.
66
Testing a Robot
Testing a Robot
Depending on the type of robot, use the tests shown in the following table to exercise the robot:
Robot Type TLD TL8 TLH ACS
Test tldtest tl8test tlhtest acstest
TL8 Example for Windows To exercise the TL8 robot c2t3l0 that is controlled by the NDMP host named stripes, use the following test and commands on Windows: Note The drive must be downed before performing this test, or avrd may interfere.
install_path\Volmgr\bin\tl8test -r stripes:c2t3l0 -d1 stripes:/dev/rmt/0cbn
When prompted, enter ? for help information. inquiry (Displays the vendor and product ID. If you get a UNIT ATTENTION message, try the mode command and then continue your testing.) s s (Checks slot status.) s d (Checks drive status.) m s3 d1 (Moves a tape from slot 3 to drive 1.) m d1 s3 (Moves the tape back to slot 3.) TLD Example for UNIX To exercise drive 1 in the TLD robot c2t3l0 that is controlled by the NDMP host stripes, use the following commands on UNIX:
/usr/openv/volmgr/bin/tldtest -r stripes:c2t3l0 -d1 stripes:/dev/rmt/Ocbn
When prompted, enter ? for help information. inquiry (Displays the Vendor and Product ID. If you get a UNIT ATTENTION message, try the mode command and then continue your testing.)
67
Testing a Robot
s s (Checks slot status.) s d (Checks drive status.) m s3 d1 (Moves a tape from slot 3 to drive 1.) unload d1 (Unloads the tape.) m d1 s3 (Moves the tape back to slot 3.) TLH Example for UNIX To exercise drive 1 in a TLH robot, use the following command on UNIX:
/usr/openv/volmgr/bin/tlhtest -r /dev/lmcpo -d1 stripes:/dev/rmt/Ocbn
Note that a TLH robot cannot attach directly to the NDMP host; only a TLH drive can directly attach to the NDMP host. When prompted, enter ? for help information. inv (Inventories the robot.) drstat (Shows drive status.) m media_id drive_name (Moves specified media to the specified drive.) dm drive_name (Dismounts the tape.) unload drive_name (Unloads the tape.)
68
Using Scripts
This chapter explains how to customize the NDMP-specific notify scripts.
Note Before using the notify scripts on UNIX, ensure they are executable by other. Do this by executing chmod 755 script_name, where script_name is the name of the script. The UNIX scripts are provided as examples only. You must customize the scripts before using them. For example, the -ne value in the first if statement must be modified to reflect the number of parameters passed. NetBackup for NDMP provides the following scripts (commands on Windows) for collecting information and providing notification of events.
Scripts to run on the NetBackup for NDMP server Scripts for UNIX ndmp_start_notify ndmp_end_notify ndmp_start_path_notify ndmp_end_path_notify ndmp_moving_path_notify Scripts for Windows ndmp_start_notify.cmd ndmp_end_notify.cmd ndmp_start_path_notify.cmd ndmp_end_path_notify.cmd ndmp_moving_path_notify.cmd
The scripts are similar to those already included in your NetBackup server installation. To create the scripts on UNIX, copy the bpstart_notify and bpend_notify scripts from /usr/openv/netbackup/bin/goodies (UNIX) to /usr/openv/netbackup/bin on the NetBackup for NDMP server. Then rename the copied scripts and modify as needed. You must customize the scripts before using them; see the above note.
69
On Windows, you must create the scripts from scratch.
ndmp_start_notify (UNIX)
Note Before using this script, ensure that it is executable by other on the media server. Do this by executing chmod 755 script_name, where script_name is the name of the script. The UNIX scripts are provided as examples only. You must customize the scripts before using them. For example, the -ne value in the first if statement must be modified to reflect the number of parameters passed. For the ndmp_start_notify script, the -ne value must be set to 5. On the UNIX media server, NetBackup calls the ndmp_start_notify script each time the client starts a backup operation. To use this script, create a script similar to /usr/openv/netbackup/bin/goodies/bpstart_notify on the server, and copy it to /usr/openv/netbackup/bin/ndmp_start_notify on the UNIX NetBackup for NDMP server. Then, modify the script as desired and ensure that you have execute permission. The ndmp_start_notify script executes each time a backup starts and after the tape has been positioned. This script must exit with a status of 0 for the calling program to continue and for the backup to proceed. A nonzero status causes the client backup to exit with a status of ndmp_start_notify failed. If the /usr/openv/netbackup/bin/ndmp_start_notify script exists, it executes in the foreground and the bptm process on the NetBackup for NDMP server waits for it to complete before continuing. Any commands in the script that do not end with an & character execute serially. The server expects the client to respond with a continue message within the period of time specified by the NetBackup CLIENT_READ_TIMEOUT option on the server. The default for CLIENT_READ_TIMEOUT is 300. If the script needs more time than 300 seconds, increase the value to allow more time. NetBackup passes the following parameters to the script:
Parameter $1
Description Name of the NDMP host.
70
Parameter $2 $3 $4
Description Policy name from the NetBackup catalog. Schedule name from the NetBackup catalog. One of the following: FULL
INCR (differential incremental) CINC (cumulative incremental)

$5 The NetBackup status code for the operation.
For example: ndmp_start_notify freddie cd4000s fulls FULL 0 ndmp_start_notify danr cd4000s incrementals INCR 0 ndmp_start_notify hare cd4000s fulls FULL 0 To create an ndmp_start_notify script for a specific policy or policy and schedule combination, create script files with a .policyname or .policyname.schedulename suffix. The following are two examples of script names for a policy named production that has a schedule named fulls: /usr/openv/netbackup/bin/ndmp_start_notify.production /usr/openv/netbackup/bin/ndmp_start_notify.production.fulls The first script affects all scheduled backups in the policy named production. The second script affects scheduled backups in the policy named production only when the schedule is named fulls. Note For a given backup, NetBackup uses only one ndmp_start_notify script and that is the one with the most specific name. For example, if there are both ndmp_start_notify.production and ndmp_start_notify.production.fulls scripts, NetBackup uses only ndmp_start_notify.production.fulls. The ndmp_start_notify script can use the following environment variables: BACKUPID UNIXBACKUPTIME BACKUPTIME
Chapter 8, Using Scripts
71
The NetBackup bptm process creates these variables. The following are examples of strings that are available to the script for use in recording information about a backup: BACKUPID=freddie_0857340526 UNIXBACKUPTIME=0857340526 BACKUPTIME=Sun Mar 2 16:08:46 1997
ndmp_start_notify.cmd (Microsoft Windows)

For Windows NetBackup for NDMP media servers, you can create batch scripts that provide notification whenever the client starts a backup. These scripts must reside on the media server in the following directory: install_path\NetBackup\bin Where install_path is the directory where NetBackup is installed. You can create ndmp_start_notify scripts that provide notification for all backups or just for backups of a specific policy or schedule. The ndmp_start_notify script executes each time a backup starts and after the tape has been positioned. To create a script that applies to all backups, name the script: install_path\netbackup\bin\ndmp_start_notify.cmd To create an ndmp_start_notify script that applies only to a specific policy or policy and schedule combination, add a .policyname or .policyname.schedulename suffix to the script name.
The following script applies only to a policy named days: install_path\netbackup\bin\ndmp_start_notify.days.cmd
The following script applies only to a schedule named fulls that is in a policy named days: install_path\netbackup\bin\ndmp_start_notify.days.fulls.cmd
The first script affects all scheduled backups in the policy named days. The second script affects scheduled backups in the policy named days only when the schedule is named fulls. For a given backup, NetBackup calls only one ndmp_start_notify script and checks for them in the following order: ndmp_start_notify.policy.schedule.cmd ndmp_start_notify.policy.cmd ndmp_start_notify.cmd
72
For example, if there are both ndmp_start_notify.policy.cmd and ndmp_start_notify.policy.schedule.cmd scripts, NetBackup uses only the ndmp_start_notify.policy.schedule.cmd script. Note If you are also using ndmp_end_notify scripts, they can provide a different level of notification than the ndmp_start_notify scripts. For example, if you had one of each, they could be ndmp_start_notify.policy.cmd and ndmp_end_notify.policy.schedule.cmd. When the backup starts, NetBackup passes the following parameters to the script:
Parameter %1 %2 %3 %4
Description Name of the client from the NetBackup catalog. Policy name from the NetBackup catalog. Schedule name from the NetBackup catalog. One of the following: FULL INCR CINC
%5 %6
Status of the operation is always 0 for bpstart_notify. Results file that NetBackup checks for a return code from the script. NetBackup uses %6 to pass the file name and then expects the script to create the file in the same directory as the script. If the script applies to a specific policy and schedule, the results file must be named install_path\netbackup\bin\NDMP_START_NOTIFY_RES.policy.schedule If the script applies to a specific policy, the results file must be named install_path\netbackup\bin\NDMP_START_NOTIFY_RES.policy If the script applies to all backups, the results file must be named install_path\netbackup\bin\NDMP_START_NOTIFY_RES An echo 0> %6 statement is one way for the script to create the file. NetBackup deletes the existing results file before calling the script. After the script executes, NetBackup checks the new results file for the status. The status must be 0 for the script to be considered successful. If the results file does not exist, NetBackup assumes that the script was successful.
73
The server expects the client to respond with a continue message within the period of time specified by the NetBackup CLIENT_READ_TIMEOUT option on the server. The default is 300 seconds. If the script needs more than 300 seconds, increase the value to allow more time.
ndmp_end_notify (UNIX)
Caution The ndmp_end_notify script is executed at the end of the backup. The backup does not wait for the script to complete. Note Before using this script, ensure that it is executable by other on the media server. Do this by executing chmod 755 script_name, where script_name is the name of the script. The UNIX scripts are provided as examples only. You must customize the scripts before using them. For example, the -ne value in the first if statement must be modified to reflect the number of parameters passed. For the ndmp_end_notify script, the -ne value must be set to 5. For a UNIX media server, if you need notification whenever the NDMP host completes a backup, copy /usr/openv/netbackup/bin/goodies/bpend_notify from the server, to /usr/openv/netbackup/bin/ndmp_end_notify on the UNIX NetBackup for NDMP host. Then, modify the script as desired, and ensure that you have execute permission. The ndmp_end_notify script executes each time a backup completes. NetBackup passes the following parameters to the ndmp_end_notify script:
Parameter $1 $2 $3
Description Name of the client from the NetBackup catalog. Policy name from the NetBackup catalog. Schedule name from the NetBackup catalog.
74
Parameter $4
Description One of the following: FULL

$5 Exit code from bptm.
For example: ndmp_end_notify freddie cd4000s fulls FULL 0 ndmp_end_notify danr cd4000s incrementals INCR 73 To create an ndmp_end_notify script for a specific policy or policy and schedule combination, create script files with a .policyname or .policyname.schedulename suffix. The following are two examples of script names for a policy named production that has a schedule named fulls: /usr/openv/netbackup/bin/ndmp_end_notify.production /usr/openv/netbackup/bin/ndmp_end_notify.production.fulls The first script affects all scheduled backups in the policy named production. The second script affects scheduled backups in the policy named production only when the schedule is named fulls. Note For a given backup, NetBackup uses only one ndmp_end_notify script and that is the one with the most specific name. For example, if there are both ndmp_end_notify.production and ndmp_end_notify.production.fulls scripts, NetBackup uses only ndmp_end_notify.production.fulls. The ndmp_end_notify script can use the following environment variables: BACKUPID UNIXBACKUPTIME BACKUPTIME The NetBackup bptm process creates these variables. The following are examples of strings that are available to the script for use in recording information about a backup: BACKUPID=freddie_0857340526 UNIXBACKUPTIME=0857340526 BACKUPTIME=Sun Mar 2 16:08:46 1997
Chapter 8, Using Scripts 75
ndmp_end_notify.cmd (Microsoft Windows)

For Windows media servers, you can create batch scripts that provide notification whenever the client completes a backup. These scripts must reside on the media server in the same directory as the NetBackup binaries: install_path\NetBackup\bin Where install_path is the directory where NetBackup is installed. You can create ndmp_end_notify scripts that provide notification for all backups or just for backups of a specific policy or schedule. To create an ndmp_end_notify script that applies to all backups, name the script: install_path\netbackup\bin\ndmp_end_notify.cmd To create a script that applies only to a specific policy or policy and schedule combination, add a .policyname or .policyname.schedulename suffix to the script name.
The following script applies only to a policy named days: install_path\netbackup\bin\ndmp_end_notify.days.cmd
The following script applies only to a schedule named fulls that is in a policy named days: install_path\netbackup\bin\ndmp_end_notify.days.fulls.cmd
The first script affects all scheduled backups in the policy named days. The second script affects scheduled backups in the policy named days only when the schedule is named fulls. For a given backup, NetBackup calls only one ndmp_end_notify script and checks for them in the following order: ndmp_end_notify.policy.schedule.cmd ndmp_end_notify.policy.cmd ndmp_end_notify.cmd For example, if there are both ndmp_end_notify.policy.cmd and ndmp_end_notify.policy.schedule.cmd scripts, NetBackup uses only ndmp_end_notify.policy.schedule.cmd. Note If you are also using ndmp_start_notify scripts, they can provide a different level of notification than the ndmp_end_notify scripts. For example, if you had one of each, they could be ndmp_start_notify.policy.cmd and ndmp_end_notify.policy.schedule.cmd.
76
When the backup completes, NetBackup passes the following parameters to the script:
%5
Status of the operation and is same as sent to the NetBackup server. This is 0 for successful backups and 1 for partially successful backups. If an error occurs, the status is the value associated with that error.
Note: The following file is not checked at the end of a backup. %6 Results file that NetBackup checks for a return code from the script. NetBackup uses %6 to pass the file name and then expects the script to create the file in the same directory as the script. If the script applies to a specific policy and schedule, the results file must be named install_path\netbackup\bin\NDMP_END_NOTIFY_RES.policy.schedule If the script applies to a specific policy, the results file must be named install_path\netbackup\bin\NDMP_END_NOTIFY_RES.policy If the script applies to all backups, the results file must be named install_path\netbackup\bin\NDMP_END_NOTIFY_RES An echo 0> %6 statement is one way for the script to create the file. NetBackup deletes the existing results file before calling the script. After the script executes, NetBackup checks the new results file for the status. The status must be 0 for the script to be considered successful. If the results file does not exist, NetBackup assumes that the script was successful.
77
ndmp_start_path_notify (UNIX)
Note Before using this script, ensure that it is executable by other on the media server. Do this by executing chmod 755 script_name, where script_name is the name of the script. The UNIX scripts are provided as examples only. You must customize the scripts before using them. For example, the -ne value in the first if statement must be modified to reflect the number of parameters passed. For the ndmp_start_path_notify script, the -ne value must be set to 7. To use this script, create a script similar to /usr/openv/netbackup/bin/goodies/bpstart_notify on the server, and copy it to /usr/openv/netbackup/bin/ndmp_start_path_notify on the UNIX NetBackup for NDMP server. Then, modify the script as desired and ensure that you have execute permission. On the UNIX media server, the ndmp_start_path_notify script executes before the backup process is issued to the NAS machine. This script must exit with a status of 0 for the calling program to continue and for the backup to proceed. A nonzero status causes the client backup to exit with a status of 99 (NDMP backup failure). If the /usr/openv/netbackup/bin/ndmp_start_path_notify script exists, it executes in the foreground and the bptm process on the NetBackup for NDMP server waits for it to complete before continuing. Any commands in the script that do not end with an & character execute serially. The server expects the client to respond with a continue message within the period of time specified by the NetBackup CLIENT_READ_TIMEOUT option on the server. The default for CLIENT_READ_TIMEOUT is 300. If the script needs more time than 300 seconds, increase the value to allow more time. NetBackup passes the following parameters to the script:
Parameter $1 $2 $3
Description Name of the NDMP host. Policy name from the NetBackup catalog. Schedule name from the NetBackup catalog.
78
Parameter $4
Description One of the following: FULL

$5 $6 $7 The NetBackup status code for the operation. Not used. The path being backed up.
For example: ndmp_start_path_notify freddie cd4000s fulls FULL ndmp_start_path_notify danr cd4000s incrementals INCR ndmp_start_path_notify hare cd4000s fulls FULL To create an ndmp_start_path_notify script for a specific policy or policy and schedule combination, create script files with a .policyname or .policyname.schedulename suffix. The following are two examples of script names for a policy named production that has a schedule named fulls:
/usr/openv/netbackup/bin/ndmp_start_path_notify.production /usr/openv/netbackup/bin/ndmp_start_path_notify.production.fulls
The first script affects all scheduled backups in the policy named production. The second script affects scheduled backups in the policy named production only when the schedule is named fulls. Note For a given backup, NetBackup uses only one ndmp_start_path_notify script and that is the one with the most specific name. For example, if there are both ndmp_start_path_notify.production and ndmp_start_path_notify.production.fulls scripts, NetBackup uses only ndmp_start_path_notify.production.fulls. The ndmp_start_path_notify script can use the following environment variables: BACKUPID UNIXBACKUPTIME BACKUPTIME The NetBackup bptm process creates these variables. The following are examples of strings that are available to the script for use in recording information about a backup:
Chapter 8, Using Scripts 79
BACKUPID=freddie_0857340526 UNIXBACKUPTIME=0857340526 BACKUPTIME=Sun Mar 2 16:08:46 1997
ndmp_start_path_notify.cmd (Microsoft Windows)

For Windows media servers, you can create batch scripts that provide notification before the backup process is issued to the NAS machine. These scripts must reside on the media server in the same directory as the NetBackup binaries: install_path\NetBackup\bin Where install_path is the directory where NetBackup is installed. You can create ndmp_start_path_notify scripts that provide notification for all backups or just for backups of a specific policy or schedule. To create an ndmp_start_path_notify script that applies to all backups, name the script: install_path\netbackup\bin\ndmp_start_path_notify.cmd To create a script that applies only to a specific policy or policy and schedule combination, add a .policyname or .policyname.schedulename suffix to the script name.
The following script applies only to a policy named days: install_path\netbackup\bin\ndmp_start_path_notify.days.cmd
The following script applies only to a schedule named fulls that is in a policy named days: install_path\netbackup\bin\ndmp_start_path_notify.days.fulls.cmd
The first script affects all scheduled backups in the policy named days. The second script affects scheduled backups in the policy named days only when the schedule is named fulls. For a given backup, NetBackup calls only one ndmp_start_path_notify script and checks for them in the following order: ndmp_start_path_notify.policy.schedule.cmd ndmp_start_path_notify.policy.cmd ndmp_start_path_notify.cmd For example, if there are both ndmp_start_path_notify.policy.cmd and ndmp_start_path_notify.policy.schedule.cmd scripts, NetBackup uses only ndmp_start_path_notify.policy.schedule.cmd.
80
Note If you are also using ndmp_start_notify scripts, they can provide a different level of notification than the ndmp_start_path_notify scripts. For example, if you had one of each, they could be ndmp_start_notify.policy.cmd and ndmp_start_path_notify.policy.schedule.cmd. When the backup starts, NetBackup passes the following parameters to the script:
%5
81
Parameter %6
Description Results file that NetBackup checks for a return code from the script. NetBackup uses %6 to pass the file name and then expects the script to create the file in the same directory as the script. If the script applies to a specific policy and schedule, the results file must be named install_path\netbackup\bin\NDMP_START_PATH_NOTIFY_RES.policy.sc hedule If the script applies to a specific policy, the results file must be named install_path\netbackup\bin\NDMP_START_PATH_NOTIFY_RES.policy If the script applies to all backups, the results file must be named install_path\netbackup\bin\NDMP_START_PATH_NOTIFY_RES An echo 0> %6 statement is one way for the script to create the file. NetBackup deletes the existing results file before calling the script. After the script executes, NetBackup checks the new results file for the status. The status must be 0 for the script to be considered successful. If the results file does not exist, NetBackup assumes that the script was successful.
%7
Pathname being backed up.
ndmp_end_path_notify (UNIX)
Note Before using this script, ensure that it is executable by other on the media server. Do this by executing chmod 755 script_name, where script_name is the name of the script. The UNIX scripts are provided as examples only. You must customize the scripts before using them. For example, the -ne value in the first if statement must be modified to reflect the number of parameters passed. For the ndmp_end_path_notify script, the -ne value must be set to 7. For a UNIX media server, if you need notification whenever the NDMP host completes a backup, copy
82 NetBackup for NDMP System Administrators Guide
/usr/openv/netbackup/bin/goodies/bpend_notify from the server, to /usr/openv/netbackup/bin/ndmp_end_path_notify on the UNIX NetBackup for NDMP host. Then, modify the script as desired, and ensure that you have execute permission. The ndmp_end_path_notify script executes after the NAS machine has informed NetBackup that it has completed sending data. NetBackup passes the following parameters to the ndmp_end_notify script:
Parameter $1 $2 $3 $4
Description Name of the client from the NetBackup catalog. Policy name from the NetBackup catalog. Schedule name from the NetBackup catalog. One of the following: FULL

$5 $6 $7 Exit code from bptm. Not used. The path being backed up.
For example: ndmp_end_path_notify freddie cd4000s fulls FULL 0 ndmp_end_path_notify danr cd4000s incrementals INCR 73 To create an ndmp_end_path_notify script for a specific policy or policy and schedule combination, create script files with a .policyname or .policyname.schedulename suffix. The following are two examples of script names for a policy named production that has a schedule named fulls: /usr/openv/netbackup/bin/ndmp_end_path_notify.production /usr/openv/netbackup/bin/ndmp_end_path_notify.production.fulls
83
The first script affects all scheduled backups in the policy named production. The second script affects scheduled backups in the policy named production only when the schedule is named fulls. Note For a given backup, NetBackup uses only one ndmp_end_path_notify script and that is the one with the most specific name. For example, if there are both ndmp_end_path_notify.production and ndmp_end_path_notify.production.fulls scripts, NetBackup uses only ndmp_end_path_notify.production.fulls. The ndmp_end_path_notify script can use the following environment variables: BACKUPID UNIXBACKUPTIME BACKUPTIME The NetBackup bptm process creates these variables. The following are examples of strings that are available to the script for use in recording information about a backup: BACKUPID=freddie_0857340526 UNIXBACKUPTIME=0857340526 BACKUPTIME=Sun Mar 2 16:08:46 1997
ndmp_end_path_notify.cmd (Microsoft Windows)

For Windows media servers, you can create batch scripts that provide notification whenever the client is finished writing to tape. These scripts must reside on the media server in the same directory as the NetBackup binaries: install_path\NetBackup\bin Where install_path is the directory where NetBackup is installed. You can create ndmp_end_path_notify scripts that provide notification for all backups or just for backups of a specific policy or schedule. To create an ndmp_end_path_notify script that applies to all backups, name the script: install_path\netbackup\bin\ndmp_end_path_notify.cmd To create a script that applies only to a specific policy or policy and schedule combination, add a .policyname or .policyname.schedulename suffix to the script name.
The following script applies only to a policy named days: install_path\netbackup\bin\ndmp_end_path_notify.days.cmd
84
The following script applies only to a schedule named fulls that is in a policy named days: install_path\netbackup\bin\ndmp_end_path_notify.days.fulls.cmd
The first script affects all scheduled backups in the policy named days. The second script affects scheduled backups in the policy named days only when the schedule is named fulls. For a given backup, NetBackup calls only one ndmp_end_path_notify script and checks for them in the following order: ndmp_end_path_notify.policy.schedule.cmd ndmp_end_path_notify.policy.cmd ndmp_end_path_notify.cmd For example, if there are both ndmp_end_path_notify.policy.cmd and ndmp_end_path_notify.policy.schedule.cmd scripts, NetBackup uses only ndmp_end_path_notify.policy.schedule.cmd. Note If you are also using ndmp_end_notify scripts, they can provide a different level of notification than the ndmp_end_path_notify scripts. For example, if you had one of each, they could be ndmp_end_notify.policy.cmd and ndmp_end_path_notify.policy.schedule.cmd. When the backup completes, NetBackup passes the following parameters to the script:
%5
Note: The following file is not checked when using ndmp_end_path_notify.
85
Parameter %6
Description Results file that NetBackup checks for a return code from the script. NetBackup uses %6 to pass the file name and then expects the script to create the file in the same directory as the script. If the script applies to a specific policy and schedule, the results file must be named install_path\netbackup\bin\NDMP_END_PATH_NOTIFY_RES.policy.sched ule If the script applies to a specific policy, the results file must be named install_path\netbackup\bin\NDMP_END_PATH_NOTIFY_RES.policy If the script applies to all backups, the results file must be named install_path\netbackup\bin\NDMP_END_PATH_NOTIFY_RES An echo 0> %6 statement is one way for the script to create the file. NetBackup deletes the existing results file before calling the script. After the script executes, NetBackup checks the new results file for the status. The status must be 0 for the script to be considered successful. If the results file does not exist, NetBackup assumes that the script was successful.
%7
Pathname being backed up.
ndmp_moving_path_notify (UNIX)
Note Before using this script, ensure that it is executable by other on the media server. Do this by executing chmod 755 script_name, where script_name is the name of the script. The UNIX scripts are provided as examples only. You must customize the scripts before using them. For example, the -ne value in the first if statement must be modified to reflect the number of parameters passed. For the ndmp_moving_path_notify script, the -ne value must be set to 7. To use this script, create a script similar to
86
/usr/openv/netbackup/bin/goodies/bpstart_notify on the server, and copy it to /usr/openv/netbackup/bin/ndmp_moving_path_notify on the UNIX NetBackup for NDMP server. Then, modify the script as desired and ensure that you have execute permission. On UNIX media servers, the ndmp_moving_path_notify script executes once the backup process has sent data to NetBackup. If the /usr/openv/netbackup/bin/ndmp_moving_path_notify script exists, it executes in the foreground and the bptm process on the NetBackup for NDMP server waits for it to complete before continuing. Any commands in the script that do not end with an & character execute serially. The server expects the client to respond with a continue message within the period of time specified by the NetBackup CLIENT_READ_TIMEOUT option on the server. The default for CLIENT_READ_TIMEOUT is 300 seconds. If the script needs more than 300 seconds, increase the value to allow more time. NetBackup passes the following parameters to the script:
Parameter $1 $2 $3 $4
Description Name of the NDMP host. Policy name from the NetBackup catalog. Schedule name from the NetBackup catalog One of the following: FULL

$5 $6 $7 The NetBackup status code for the operation. Not used. The path being backed up.
For example: ndmp_moving_path_notify freddie cd4000s fulls FULL
87
ndmp_moving_path_notify danr cd4000s incrementals INCR ndmp_moving_path_notify hare cd4000s fulls FULL To create an ndmp_moving_path_notify script for a specific policy or policy and schedule combination, create script files with a .policyname or .policyname.schedulename suffix. The following are two examples of script names for a policy named production that has a schedule named fulls:
/usr/openv/netbackup/bin/ndmp_moving_path_notify.production /usr/openv/netbackup/bin/ndmp_moving_path_notify.production.fulls
The first script affects all scheduled backups in the policy named production. The second script affects scheduled backups in the policy named production only when the schedule is named fulls. Note For a given backup, NetBackup uses only one ndmp_moving_path_notify script and that is the one with the most specific name. For example, if there are both ndmp_moving_path_notify.production and ndmp_moving_path_notify.production.fulls scripts, NetBackup uses only ndmp_moving_path_notify.production.fulls. The ndmp_moving_path_notify script can use the following environment variables: BACKUPID UNIXBACKUPTIME BACKUPTIME The NetBackup bptm process creates these variables. The following are examples of strings that are available to the script for use in recording information about a backup: BACKUPID=freddie_0857340526 UNIXBACKUPTIME=0857340526 BACKUPTIME=Sun Mar 2 16:08:46 1997
ndmp_moving_path_notify.cmd (Microsoft Windows)

For Windows media servers, you can create batch scripts that provide notification whenever the NAS machine starts sending data. These scripts must reside on the media server in the same directory as the NetBackup binaries: install_path\NetBackup\bin Where install_path is the directory where NetBackup is installed. You can create ndmp_moving_path_notify scripts that provide notification for all backups or just for backups of a specific policy or schedule.
88 NetBackup for NDMP System Administrators Guide
To create an ndmp_moving_path_notify script that applies to all backups, name the script: install_path\netbackup\bin\ndmp_moving_path_notify.cmd To create a script that applies only to a specific policy or policy and schedule combination, add a .policyname or .policyname.schedulename suffix to the script name.
The following script applies only to a policy named days: install_path\netbackup\bin\ndmp_moving_path_notify.days.cmd
The following script applies only to a schedule named fulls that is in a policy named days: install_path\netbackup\bin\ndmp_moving_path_notify.days.fulls.cmd
The first script affects all scheduled backups in the policy named days. The second script affects scheduled backups in the policy named days only when the schedule is named fulls. For a given backup, NetBackup calls only one ndmp_moving_path_notify script and checks for them in the following order: ndmp_moving_path_notify.policy.schedule.cmd ndmp_moving_path_notify.policy.cmd ndmp_moving_path_notify.cmd For example, if there are both ndmp_moving_path_notify.policy.cmd and ndmp_moving_path_notify.policy.schedule.cmd scripts, NetBackup uses only ndmp_moving_path_notify.policy.schedule.cmd. Note If you are also using ndmp_start_notify scripts, they can provide a different level of notification than the ndmp_moving_path_notify scripts. For example, if you had one of each, they could be ndmp_start_notify.policy.cmd and ndmp_moving_path_notify.policy.schedule.cmd. When the backup starts, NetBackup passes the following parameters to the script:
Parameter %1 %2 %3
Description Name of the client from the NetBackup catalog. Policy name from the NetBackup catalog. Schedule name from the NetBackup catalog.
89
Parameter %4
Description One of the following: FULL INCR CINC
%5
Note: The following file is not checked when using ndmp_moving_path_notify. %6 Results file that NetBackup checks for a return code from the script. NetBackup uses %6 to pass the file name and then expects the script to create the file in the same directory as the script. If the script applies to a specific policy and schedule, the results file must be named install_path\netbackup\bin\NDMP_END_NOTIFY_RES.policy.schedule If the script applies to a specific policy, the results file must be named install_path\netbackup\bin\NDMP_END_NOTIFY_RES.policy If the script applies to all backups, the results file must be named install_path\netbackup\bin\NDMP_END_NOTIFY_RES An echo 0> %6 statement is one way for the script to create the file. NetBackup deletes the existing results file before calling the script. After the script executes, NetBackup checks the new results file for the status. The status must be 0 for the script to be considered successful. If the results file does not exist, NetBackup assumes that the script was successful. %7 Pathname being backed up.
90
Index
Numerics 10000, port (used by NDMP) 60 A accessibility features ix acstest 67 Activity Monitor interface 63 Add Drive dialog 31, 35 Add Robot dialog 29 adding drives 31, 35 Media Manager storage unit 47 NDMP storage units 35 robots 28 volumes 33 Advanced Client 3 access web info x authorization NDMP user and password 24 auto discovery of devices 2, 23, 52 avrd 60 B backup automatic 56 format 60 level (NDMP vs. NetBackup) 62 local vs. three-way 2, 5, 8, 14 manual, of NDMP policy 56 ndmp_end_notify script UNIX 74 Windows 76 ndmp_end_path_notify script UNIX 83 Windows 84 ndmp_moving_path_notify script UNIX 87 Windows 88 ndmp_start_notify script UNIX 70 Windows 72 ndmp_start_path_notify script UNIX 78 Windows 80 overview 14 procedure 56 three-way, configuring for 27 types allowed 38 C client list 37 clustering 3, 43 configuration add Media Manager storage unit 47 add NDMP storage unit 35 add volumes 33 adding drives/robots 28 Backup Selections list 38 check Media Manager 33 client list 37 drive in media manager 35 drive, for NDMP-attached host 31 for clustering 43 general policy attributes 37 NDMP policy 37 policy storage unit 37 policy type 37 robot in Media Manager 28 schedules 38 testing 44 control panel, Windows 63 D DAR 3, 18 defined 4 how to turn on/off 40 debug logs 62 deinstallation 91
server 22 Device Configuration Wizard 2, 23, 52 Device Monitor 33 different client restore 5 Direct Access Recovery (see DAR) drive add to Media Manager 35 adding, for NDMP-attached host 31 duplex mode and performance 60 E environment variables, in Backup Selections list 38 exclude files, using SET directive 38 list, using 38 F fail over 43 file list 38 file names (not allowed in Backup Selections list) 38, 60 H High Availability 3, 43 I ICMP protocol 60 installation 19 deinstallation 22 load from media 20 prerequisites 19 instant recovery 3 J jnbSA 56 L LEVEL (NDMP backup) 62 log directories 62, 63, 64 M Media Manager configuring 28 storage units 46 troubleshooting 63, 64 N NAS snapshot 3, 23, 24, 37, 47, 55 nbjm 61 nbpem 61 nbrb 61 NDMP 92
access web info x backup, manual 56 client type 37 client, definition of 4 host name, entering 30 host, definition of 4 LEVEL, related to NetBackup backups 62 policy adding 37 attributes 37 clients 37 files 38 schedules 38 policy storage unit attribute configuration 37 policy type configuration 37 overview 10 protocol 4, 6, 60 restore 57 restrictions 60 server application, definition of 4 storage unit, adding 35 storage unit, definition of 5 to media server 4, 27, 37, 46 how to configure 47 ndmp logging 61 NDMP to media server 2, 9 ndmp_end_notify script UNIX 74 Windows 76 ndmp_end_path_notify script UNIX 83 Windows 84 ndmp_moving_path_notify script UNIX 87 Windows 88 ndmp_start_notify script UNIX 70 Windows 72 ndmp_start_path_notify script UNIX 78 Windows 80 ndmpagent legacy debug log 62 unified logging 61 NetBackup Administration Console 56 NetBackup for NDMP NetBackup for NDMP System Administrators Guide
configuration 23 definition 1 features 2 installation 19 server, definition 4 troubleshooting 61 network interface cards 60 NIC cards and full duplex 60 notification scripts 69 O on demand storage unit 36 operating notes and restrictions 60 Override policy storage unit, setting 38 overwriting files 57 P password verifying 27, 34 path length limit 60 path-based history 3 peripherals (latest info on web) x ping 60 point-in-time snapshots 3 policy attributes 37 port 10000 (used by NDMP) 60 protocol supported (NDMP) 2, 23 R remote NDMP 46 reserved environment variables 38 restart device manager 30 Media Manager 32 restore local vs. three-way 5, 8, 14 overview 16 overwriting files 57 procedure 57 three-way 16 to different client 5, 10 restrictions NetBackup for NDMP 60 robot adding 28 robotic control 29 supported types 11 test device configuration 67 robot connection
verifying 34 Robot Control Host, for volume 33 S schedules 38 scripts notification 69 SET directive 39 Shared Storage Option (see SSO) snapshots 3 SnapVault 3, 37 SSO 2 configuration overview 51 storage devices auto discovery 2, 23 storage unit adding 35 media manager type 46 NDMP type, overview 11 specify for NDMP policy 37 support web site (VERITAS) x supported robots 11 T tape libraries supported 11 terminology, NetBackup for NDMP 4 testing configuration 44 three-way backup 5 configuring for 27 tl8test 67 tldtest 67 tlhtest 67, 68 tpautoconf 34, 51 troubleshooting 59 type of backup allowed 38 of policy 37 of storage unit 36 U unified logging 61 uninstalling NetBackup 22 user-directed backups and archives 10 backups and archives, not allowed 56 restores, not allowed 57 V variables, environment 38 vendors (latest info on) x verifying NDMP password 27 93
Index
version supported (NDMP) 2, 23 volumes, add to Media Manager 33 vxlogview 61
W web access to product info x web access to recent Advanced Client info x wildcards, in Backup Selections list 38, 60 Windows control panel 63
94

Veritas Netbackup 6.0 For NDMP: System Administrator'S Guide

Uploaded by

Copyright:

Available Formats

Veritas Netbackup 6.0 For NDMP: System Administrator'S Guide

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Veritas Netbackup 6.0 For NDMP: System Administrator'S Guide

Uploaded by

Copyright:

Available Formats

VERITAS NetBackup 6.

N15271C September 2005

NetBackup for NDMP System Administrators Guide

NetBackup for NDMP System Administrators Guide

Finding NetBackup Documentation

Accessing the VERITAS Technical Support Web Site

NetBackup for NDMP System Administrators Guide

b. After providing the required information, click Send Message.

Contacting VERITAS Licensing

For more information, see the NetBackup Installation Guide.

Comment on the Documentation

Comment on the Documentation

NetBackup for NDMP Information on the Web

Advanced Client Information on the Web

NetBackup for NDMP System Administrators Guide

Introduction to NetBackup for NDMP

NetBackup for NDMP Features

NetBackup for NDMP Features

NetBackup for NDMP System Administrators Guide

NetBackup for NDMP Features

Chapter 1, Introduction to NetBackup for NDMP

NetBackup for NDMP Terminology

NetBackup for NDMP Terminology

NetBackup for NDMP System Administrators Guide

NetBackup for NDMP Terminology

Chapter 1, Introduction to NetBackup for NDMP

Network Data Management Protocol (NDMP)

Network Data Management Protocol (NDMP)

NDMP and NetBackup Hosts as Clients of Each Other

NetBackup for NDMP System Administrators Guide

Types of NDMP Backup

Types of NDMP Backup

NDMP Local Backup

LAN/WAN NDMP host

NetBackup for NDMP server

FC/SAN Disks Tape library

Storage devices on SAN

Chapter 1, Introduction to NetBackup for NDMP

Types of NDMP Backup

NDMP Three-Way Backup

LAN/WAN NDMP host NDMP Host

NetBackup for NDMP server

Disks Three-Way NDMP backup

NetBackup for NDMP System Administrators Guide

Types of NDMP Backup

Backup to Media Manager Storage Devices (Remote NDMP)

LAN / WAN NetBackup for NDMP server NDMP host

Storage Devices on SAN

Chapter 1, Introduction to NetBackup for NDMP

NetBackup for NDMP System Administrators Guide

NDMP Storage Units

Media Manager Storage Units

Assigning Tape Drives to Different Hosts

For non-NDMP clients of NetBackup

Chapter 1, Introduction to NetBackup for NDMP

Drive-control commands for NDMP

NB for NDMP media server

Drive 4 TLD Robot

NetBackup for NDMP System Administrators Guide