Scribd
Upload
186 views

DSP Connection Diagram

This document provides a system block diagram and overview of the hardware, interfaces/ports, power supply connection, motor driver connection, and X/Y limit switch connection for a laser engraving/cutting machine main board and LCD display. The main board dimensions are 192mm x 115mm and the LCD display is 100.0mm x 92.0mm. The interface includes ports for USB/PC connection, laser control, I/O, and limits for the X, Y, Z, and U axes.

Uploaded by

blondu007
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
186 views

DSP Connection Diagram

This document provides a system block diagram and overview of the hardware, interfaces/ports, power supply connection, motor driver connection, and X/Y limit switch connection for a laser engraving/cutting machine main board and LCD display. The main board dimensions are 192mm x 115mm and the LCD display is 100.0mm x 92.0mm. The interface includes ports for USB/PC connection, laser control, I/O, and limits for the X, Y, Z, and U axes.

Uploaded by

blondu007
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 8

1.

System Block Diagram

U disk Display mainboard data

PC

USB Connection

2. Hardware
a. Dimension of the main board
192mm

115mm

b. Dimension of the LCD display

3.8

100.0 92.0

142.0 4.0 3*10 150.0 4.0 10.0

3. Interface and ports

JPO 24V DC (input)

U disk 24VDC

Laser 2

LASE R_CO MTRO LLER_ V4.2

Laser 1

IO
USB/PC

Display Z/U limit

X/Y limit

X axis

Y axis

Z axis

U axis

Pin Definition Pin 1 JPO


Laser 1

2 24V VCC TTL-H

24V GND GND

TTL-L

Output

Water-flow enable Footswitch PWM+ PWM+ PWM+ PWM+ X+limit of the maximum coordinate Z+limit of the maximum coordinate 5V+ 5V+ 5V+ 5V+

Laser 2

GND GND GND GND GND GND output GND output GND output

TTL-H DIR+ DIR+ DIR+ DIR+ Y-limit of 0 coordinate U-limit of 0 coordinate open cover(input)

TTL-L DIRDIRDIRDIRY+limit of the maximum coordinate U+limit of the maximum coordinate Air blower (input)

Output PWMPWMPWMPWMX-, limit of 0 coordinate

X-axis Y-axis Z-axis U-axis

X/Y limit

5V+

U/Z limit

5V+

IO

5V+(output)

4. Power supply connection

5. Motor driver connection


A) Rising Edge Pulse
(Most common connection)
X/Y/Z/U 6 5V 5 PWM+ 4 PWM3 DIR2 DIR+ 1 GND Common anode connection DRPUDR+ PU+

X/Y/Z/U 6 5V 5 PWM+ 4 PWM3 DIR2 DIR+ 1 GND Differential connection

PU+

PUDR+

DR-

B) Falling Edge Pulse


X/Y/Z/U 6 5V 5 PWM+ 4 PWM3 DIR2 DIR+ 1 GND Common anode connection X/Y/Z/U 6 5V 5 PWM+ 4 PWM3 DIR2 DIR+ 1 GNDDifferential connection DRPUDR+ PU+ DRPUDR+ PU+

X/Y/Z/U 6 5V 5 PWM+ 4 PWM3 DIR2 DIR+ 1 GND-

+5V

PU

DR

6. X/Y Limit SW Connection

You might also like