Scribd
Upload
69 views5 pages

Politehnički Fakultet U Zenici Katedra Za Industrijski Inženjering I CIM Tehnologije Predmet: Upravljanje Proizvodnjom

The document describes a transport project that analyzes three options for transporting goods: carts, forklift, and conveyor belt. It calculates characteristics like load size, travel time, cycle time, and capacity for each option. Boundary conditions are defined and costs are presented in a table. A graph shows the boundary regions for each option based on minimizing costs. The optimal transport option is determined to be a forklift for transporting 5,500 units, as it can complete the task in one shift without fully utilizing its capacity.

Uploaded by

Lori Brady
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
69 views5 pages

Politehnički Fakultet U Zenici Katedra Za Industrijski Inženjering I CIM Tehnologije Predmet: Upravljanje Proizvodnjom

The document describes a transport project that analyzes three options for transporting goods: carts, forklift, and conveyor belt. It calculates characteristics like load size, travel time, cycle time, and capacity for each option. Boundary conditions are defined and costs are presented in a table. A graph shows the boundary regions for each option based on minimizing costs. The optimal transport option is determined to be a forklift for transporting 5,500 units, as it can complete the task in one shift without fully utilizing its capacity.

Uploaded by

Lori Brady
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 5

POLITEHNIKI FAKULTET U ZENICI Katedra za industrijski inenjering i CIM tehnologije Predmet: Upravljanje proizvodnjom

PROJEKTNI ZADATAK BROJ 2


- izbor transportnog problema-

Student:

Predmetni asistent: mr. sc. Alan Lisica, dipl.ma.ing

Broj indexa: PB-29/12

Izrada zadatka 1.Odreivanje karakteristika transporta za sve tri varijante transportnog sredstva Veliine utovara su :

( ( ( )

) )

Vrijeme kretanja u radnom hodu je :

( ( )

Vrijeme kretanja u povratnom hodu je :

Vrijeme trajanja ciklusa je : ( ( ) )

Kolica i viljukar rade prekidno i u svakom ciklusu prenesu po jednu veliinu tereta odnosno , dok transporter radi kontinuirano nosei veliinu utovara rasporeenu du trake transportera . Korisni kapaciteti za granine sluajeve su : ( ) ( )

Stepen iskoritenja je :

Karakteristike procesa za po dva granina sluaja i za sve tri varijante raunamo prema izrazu :

) ( )

) (
( ) ( )

2.Grafiki prikaz graninih podruja primjene pojedinih varijanti po principu najmanjih trokova Tabela graninih sluajeva je :

Tabela 1.
Trokovi u novanim jedinicama Sredstva transporta [ ] [ ] [ ] [ ] [ ] [ ] [ ]

0 Kolica 9.616,40

0 70.971 48,45

70.971

1.912,5

92.660,63

163.631,63

0 Viljukar 18.188,11

0 91.487 34,58

91.487

1.912,5

66.134,25

157.621,25

0 Transporter 294.953,40

0 168.525 63,20

168.525

1.912,5

120.870

289.395

Slika 1.

3. Odreivanje optimalne varijante transportnog sredstva Iz prikaza graninih podruja vidi se da je za Q = 5.500 ( varijanta elektro viljukar. ) optimalna

Grafiki prikaz dat je za po jednu jedinicu transportnog sredstva. Ovo znai da je za transportovanje koliine tereta od 5.500 ( samo jedna jedinica optimalne varijante. ) dovoljno

Takoe iz prikaza se vidi da e odabrano transportno sredstvo izvriti traeni zadatak transponovanja radei samo u jednoj smjeni ne koristei ni taj reim u potpunosti. Pri punom koritenju jedne smjene viljukar bi mogao prenijeti koliinu od ( ) Stepen angaovanja je :

You might also like