Scribd
Upload
882 views

ServiceManual For Data Communication EU

This document provides instructions for connecting various TOMEY products to a PC for data communication. It discusses using either X-modem or Z-modem protocols depending on the product. For X-modem products, the communication settings are specified, while for Z-modem products the data will be sent as a CSV file called TOMEY.csv that can be opened in Excel. Proper connection of the RS-232 cable and setting of the baud rate, data bits, parity and stop bits is required.

Uploaded by

Ashan Jayawardena
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
882 views

ServiceManual For Data Communication EU

This document provides instructions for connecting various TOMEY products to a PC for data communication. It discusses using either X-modem or Z-modem protocols depending on the product. For X-modem products, the communication settings are specified, while for Z-modem products the data will be sent as a CSV file called TOMEY.csv that can be opened in Excel. Proper connection of the RS-232 cable and setting of the baud rate, data bits, parity and stop bits is required.

Uploaded by

Ashan Jayawardena
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

Service Manual

Data Communication

v1.1

1. Information for data communication


Many of TOMEY products can send measurement data to PC. This is an instruction to do data communication between PC and TOMEY unit. Required tool 1) RS-232C cable (2m, cross-link, male-female) Art-No. 904-036 2) Software (ex: Hyper terminal)

Communication protocol X-modem: TL-900, TL-2000, TL-3000, TL-2000A, TL-3000A. TR-1000, RC-1000, TR-3000, RC-3000, TR-4000, RC-4000, RC-5000, AL-2000, UD-6000 (older software than 1.30/2.20) Z-modem: AL-100, SP-3000, AL-3000, UD-6000 (new software than and 1.30/2.20) Other way: TMS-3, TMS-4, RT-6000

<Page 1>

Service Manual

Data Communication

V1.1

2. Communication with X-modem format product.


1. Connect the Computer and TOMEY unit by RS-232C cable. (If you need, use gender changer) 2. Open software which can read binary code. (For example: HyperTerminal) 3. Adjust communication condition on Tomey unit and communication software of the computer (Baud rate, Data bit, Parity, Stop bit and so on) 4. Collect some data on the Tomey unit and send data to the computer (Carriage return should be active by setting of software)

*Caution If Tomey product cannot change communication condition, PC has to adjust as follows. Baud Rate Data bit Parity Stop bit Data code Flow control 2400 bps 7bit Even 1bit ASCII Xon/Xoff

<Page 2>

Service Manual

Data Communication

V1.1

3. Communication with Z-modem format product.


1. Connect the Computer and TOMEY unit by RS-232C cable. (If you need, use gender changer) 2. Open software which can receive Z-mode-data. (For example: HyperTerminal) 3. Adjust communication condition on Tomey unit and communication software of the computer. (Baud rate, Data bit, Parity, Stop bit and so on) 4. Collect some values on the Tomey unit and send data to the computer

Information A. You will send measurement data with CSV format. This file able to be read with Microsoft Excel. B. File name is saved as TOMEY. csv. C. If you select simple Z-modem for receiving data it will save last as actual TOMEY.CSV, The Computer automatically rename the older data to TOMEY0.CSV TOMEY1.CSV TOMEY2.CSV ... D. If you select Z-modem with crash recover, new data is also TOMEY. CSV file. It must be removed for the next measurement

<Page 3>

You might also like