STD C0001

SYMBOLS
( DATE)
PERMANENT SURVEY MARK SURVEY STATION S&C PIT S&C RELAY
NOTES:
1.
DIMENSION: UNLESS SHOWN OTHERWISE, ALL DIMENSIONS ARE IN MILLIMETRES.
12. DRAINAGE
MINIMUM FALL OF 1 IN 300 FOR ALL DRAINAGE PIPE OR AS TO REQUIRED CALCULATION. BACKFILL 0F 20mm SINGLE SIZE AGGREGATE TO A MINIMUM COVER OF 100mm ABOVE THE PIPE.
2.
STAUNCHION RAILWAY OVERHEAD STRUCTURE GUY LIGHT POLE POWER POLE ELECTRICITY PIT
( SI GNATURE)
PEDESTRIAN GATE, FENCING AND FOUNDATION DETAILS: FOR DETAILS AND SPECIFICATIONS RELATING TO PEDESTRIAN MAZE ENCLOSURE, ARRANGEMENTS, EQUIPMENT AND FOUNDATION DETAILS. REFER TO SHEETS 3, 4, 5 AND 6.
12.1
DRAINAGE PIPE ACROSS TRACKS CLASS 4 RCP PIPE OR EQUIVALENT AT MINIMUM DEPTH OF 1200mm FROM TOP OF RAIL TO TOP OF PIPE. RECOMMENDED MINIMUM PIPE SIZE OF 600mm FOR REGIONAL AREA.
12.2 3.
INSTALLATION & REFERENCE UNLESS NOTED OTHERWISE, INSTALLATION, SIGNAGE, UNSPECIFIED DIMENSIONS & ASSOCIATED WORKS SHALL BE IN ACCORDANCE WITH DRAWINGS / REFERENCES AS BELOW: 3.1 CRITERIA FOR INFRASTRUCTURE AT RAILWAY CROSSING - PEDESTRIAN CROSSINGS 3.2 MANUAL OF UNIFORM TRAFFIC CONTROL DEVICES RAILWAY CROSSINGS 3.3 3.4 3.5 KERBS STANDARD FOR SIGNALLING DESIGN AND DOCUMENTATION SPECIFICATION FOR SIGNALLING SUPPLY, CONSTRUCTION AND INSTALLATION VICROADS SD 2001 VRIOGS 012.1 VRIOGS 012.2 AS1742.7 VRIOGS 003.2
DRAINAGE PIPE ALONG TRACK CLASS 3 RCP PIPE OR EQUIVALENT AT ABOUT 2700mm FROM RUNNING EDGE OF NEAREST RAIL AT DEPTH OF OPEN DRAIN, MINIMUM SIZE 225mm
12.3
SUB SURFACE DRAIN USE MEGAFLOW STRIP DRAIN, APPROX. SIZE 300 x 40 OR 100 -150mm ROUND SLOTTED FRC PIPE IN FILTER SOCK (BIDIM A14) OR APPROVED EQUIVALENT. BIDIM A14 MAY BE USED AS A SEPARATOR BETWEEN THE BALLAST AND THE DRAINAGE LINES. SUB SURFACE DRAIN TO BE CONNECTED TO EXISTING DRAINAGE PIPE, PIT OR RUN OFF TO NATURAL SURFACE. USE MINIMUM TO ROUND PIPE AS REQUIRED.
FLASHING LIGHTS
IRJ
INSULATED RAIL JOINT SIGNAL TELECOM POLE TELECOM PIT TELECOM PILLAR G & F VALVE STOP VALVE FIRE PLUG FIRE HYDRANT SIDE ENTRY PIT
13. STEPS & HANDRAILS

ANY STEPS AND HANDRAILS ASSOCIATED WITH PEDESTRIAN/LEVEL CROSSINGS ARE TO BE PROVIDED IN ACCORDANCE WITH AS 1428.2.
4.
SIGNS & ROAD MARKING PAVEMENT MARKINGS & SIGNS SHALL BE SUPPLIED AND INSTALLED IN ACCORDANCE WITH AS1742.2, AS1742.7 & AS1743
( BL OCK L ETTERS)
GRATED PIT DRAINAGE PIT SEWER PIT TREE
5.
GRADES ALL PROPOSED PATHS TO BE GRADED NO STEEPER THAN 1:14. CROSS FALL TO BE PROVIDED FOR LEVEL PATHWAY, MAX. 1:40. ARROW FOR GRADE SHOWN ON DRAWING REPRESENTS DOWN DIRECTION.
SERVICES LEGEND
GUARD FENCE FENCE ON BOUNDARY
6.
TREATMENT OF RAILS RAILS THROUGH LEVEL CROSSING SHALL BE PAINTED WITH BITUMINOUS PAINT, TYPE 711 CHASSIS BLACK OR EQUIVALENT. COATINGS SHALL BE ON ALL SURFACES OF RAILS EXCEPT TOP AND RUNNING EDGE SURFACE. COATINGS TO EXTEND BEYOND THE PAVED AREA BUT MUST CEASE AT LEAST 1m FROM RAIL JOINTS.
Ce r t i f i e d By :
FENCE COMPRESSED AIR - ABOVE GROUND COMPRESSED AIR - UNDER GROUND DRAIN - ABOVE GROUND DRAIN - UNDER GROUND ELECRICITY - ABOVE GROUND ELECTRICITY - UNDER GROUND LOW VOLTAGE ELECRICITY - A. GROUND LOW VOLTAGE ELECTRICITY - U. GROUND HIGH VOLTAGE ELECRICITY - A. GROUND HIGH VOLTAGE ELECTRICITY - U. GROUND FUEL - ABOVE GROUND 9. 8.
7.
SERVICES UNDERGROUND SERVICES IF SHOWN ARE APPROXIMATE ONLY. SERVICES INFORMATION OBTAINED FROM "DIAL BEFORE YOU DIG" AT THE TIME OF DESIGN ACTUAL LOCATIONS ARE TO BE DETERMINED ON SITE PRIOR TO COMMENCEMENT OF WORK. RETAINING WALLS WHERE INDICATED, RETAINING WALLS TO BE PROVIDED IN ACCORDANCE WITH AS 4678, EARTH RETAINING STRUCTURES. BOLLARDS
MIN. 150 DOMED TREATED PINE

1 2 0 0
FUEL - UNDER GROUND GAS - ABOVE GROUND GAS - UNDER GROUND CONCRETE HP GAS - UNDER GROUND OPTIC FIBRE - ABOVE GROUND OPTIC FIBRE - UNDER GROUND HP OIL - ABOVE GROUND HP OIL - UNDER GROUND PIPELINE - ABOVE GROUND PIPELINE - UNDER GROUND SERVICE DUCT SEWER - ABOVE GROUND SEWER - UNDER GROUND SIGNALS & COMMS SERVICE LINE - A.G. SIGNALS & COMMS SERVICE LINE - U.G. SIGNAL RODING ABOVE GROUND TELSTRA - LINE ABOVE GROUND
$ NAM E$
OR EQUIVALENT
50
MIN.
FOOTING
10. TACTILE GROUND SURFACE INDICATORS WHERE INDICATED, TGSIs TO BE PROVIDED IN ACCORDANCE WITH AS 1428.4. COLOUR: YELLOW, SIZE 300mm x 300mm MATERIAL: MASONRY FOR ASPHALT PAVEMENT, RUBBER FOR CONCRETE PAVEMENT. WHERE INDICATED, RAISED PAVEMENT MARKERS (R.P.Ms) TO BE PROVIDED IN ACCORDANCE WITH VRIOGS 003.2. 11. LIGHTING ADEQUATE LIGHTING TO BE PROVIDED BY COUNCIL / STAKEHOLDERS. ANY LIGHTING PROVIDED SHOULD BE IN ACCORDANCE WITH AS 1158.3.1 AND VRIOGS 003.2.
TELSTRA - UNDER GROUND SIGNALS TROUGHING - ABOVE GROUND SIGNALS TROUGHING - UNDER GROUND UNIDENTIFIED SERVICE WATER SUPPLY - ABOVE GROUND WATER SUPPLY - UNDER GROUND V/LINE Consultant
This drawing has been prepared by, or compiled from information provided by, persons other than Victrack. To the maximum extent permissible by law, Victrack takes no responsibility for, and makes no representations in relation to, the completeness, accuracy or quality of any information contained in this drawing. Each user of this drawing releases Victrack from all and any loss, damage, cost, expense or liability in relation to the use of, or any reliance on, this drawing or the information contained in it. All written dimensions take precedence over scaled dimensions.
3 0 0
HP GAS - ABOVE GROUND
MI N.
OPERATORS METRO
AUTHORISED BY
DATE
Ahmed Dwidar Shane Cooper

Drawn By B.C. Checked By A.C.
04/05/12 13/06/12
Designed By B.C. Ind. Review
$ TI M E$
RAILWAY TRACK AND CIVIL STANDARD DRAWING

PEDESTRIAN CROSSING GENERAL NOTES & SPECIFICATIONS SHEET 1
Up Location East. North. ID# Down Location East. North. ID# Scale AS SHOWN Sheet Size A3 Datum File Name Sheet No. In Serv. STD_C0001.dgn
coffey
Franchisee / Lessee
State Government
rail
Approved H.R.E. Drawing Number
Approval Date 16/12/11 Revision
01 of 06
$ DATE$
Revised By
In Serv
Rev.
Date
Description
Designed Checked Ind. Rev. Approv.
Department of
<REDRAWN & REVISED. SUPERSEDES PLAN No. STD_R0012, STD_R0013, STD_R0014, STD_R0015, STD_R0017, STD_G0024, STD_C0012, STD_C0015, STD_C0016, STD_C0017, STD_C0018, STD_C0021, STD_C0022, F616, 117/2000>
Transport
This drawing is provided only for the information of the person or organisation to whom Victrack provides it. It may not be provided to, or used by, any other person without Victracks prior written consent.
STD_C0001
$FILE$
( DATE)
NOTES:
14.1 TRACK FOUNDATION DETAIL FOR PEDESTRIAN CROSSING SEE FLANGEWAY DETAIL 55 mm + 5 mm/-0 mm 1 IN 40 GRADE RECOMMENDED 1 IN 14 MAX. RUBBER PAVING UNITS
300
2000
C TRACK
F G H
J
BALLAST & EXISTING FORMATION
3 5mm +5mm/ 0mm
SLEEPER
0 N6 I 1
100 mm OF FULL DEPTH TYPE L ASPHALT
( SI GNATURE)
EXISTING SLEEPER
F
PIPE ALONG TRACK DRAIN ON BOTH SIDES OF RAIL TRACKS TO MATCH OPEN DRAIN. SEE NOTE 12.2 ON SHEET 1 EXTEND FULL DEPTH BALLAST TO PATH INTERFACE GEOFABRIC
25mm COMPACTED DEPTH ASPHALT SIZE 7 TYPE L CLASS C320 75mm COMPACTED DEPTH OF CLASS 2 F.C.R. CONSOLIDATED SUB-GRADE CBR GREATER THAN 5%
G H
DETAIL NTS
14.2 (b) FULL DEPTH ASPHALT PAVEMENT
7mm NOMINAL SIZE ASPHALT COMPACTED DEPTH FROM TOP OF RAIL TO TOP OF SLEEPER OVER FULL LENGTH OF SLEEPER, 2440mm WIDE & EDGE LINE R.P.Ms 170mm WIDE
1 -
14.2 (a) RUBBER PANEL PAVEMENT J

RUBBER UNIT, pedeSTRAIL OR APPROVED EQUIVALENT, 2300 mm WIDE & EDGE LINE R.P.Ms 170mm WIDE
( BL OCK L ETTERS)
2700 280 170 RAISED PAVEMENT MARKERS AS PER VRIOGS 003.2 INCORPORATED IN CONTRASTING LINE MARKING 1800 280 170 150 170
2440 150 1800 170 RAISED PAVEMENT MARKERS AS PER VRIOGS 003.2 INCORPORATED IN CONTRASTING LINE MARKING
PAINT SIDES AND FOOT OF RAIL WITH BITUMINOUS PAINT FOR CORROSION PROTECTION 60 mm + 5 mm/-0 mm
ASPHALT
3 5mm +5mm/ 0mm
ELEVATION
ELEVATION
EXISTING SLEEPER
ASPHALT PAVEMENT
EPFLEX RAIL SEAL (METRO SITES) REFER TO DETAIL 3. BITUMINOUS PAINT (REGIONAL SITES) REFER TO DETAIL 2.
5 9 0
DETAIL NTS
2 -
OUTSIDE RAIL OUTSIDE RAIL
REFER TO DETAIL 1 "pedeSTRAIL" RUBBER UNITS OR APPROVED EQUIVALENT
ASPHALT PAVEMENT
EPFLEX RAILSEAL EPFLEX RAILSEAL FIELD SIDE 60 60 270 GAUGE SIDE
ASPHALT
3 5mm +5mm/ 0mm
PLAN
PLAN
EPLOCK CLIP EXISTING SLEEPER
DETAIL NTS
$ NAM E$
3 -
Consultant
$ TI M E$
coffey
Franchisee / Lessee
State Government
rail

PEDESTRIAN CROSSING GENERAL NOTES & SPECIFICATIONS SHEET 2
Drawn By B.C. Checked By A.C. Approved H.R.E. Drawing Number
02 of 06
$ DATE$
Revised By
In Serv
Rev.
Date
Description
Department of
Transport
STD_C0001
$FILE$
SIGN "G" 1830

( DATE)
SIGN "G" 1830 CLEAR 1260 1200 HIGH SPRING LOADED GATE 1. ALL DIMENSIONS ARE IN MILLIMETRES. ALL DIMENSIONS ARE CENTRE POST TO CENTRE POST UNLESS SHOWN OTHERWISE. MINIMUM DISTANCE SHALL BE INCREASED TO ALLOW FOR CURVE EFFECTS WHEN TRACK RADIUS IS LESS THAN 600 m. 4. DESIGN LAYOUTS ARE BASED ON CURRENT VICTORIAN RAIL INDUSTRY OPERATORS GROUP STANDARDS VRIOGS 003.2. 5. 6. 7. SIGNS TO BE MANUFACTURED, SUPPLIED AND INSTALLED IN ACCORDANCE WITH VRIOGS 003.2, AS. 1742.2, AS. 1742.7 AND AS. 1743. SIGNS "B" AND "C" TO BE ANGLED TO FACE APPROACHING PEDESTRIANS. EMERGENCY ESCAPES TO HAVE 1000 WIDE SPRING LOADED GATE TO BE NORMALLY CLOSED AND OPEN ONLY IN DIRECTION INDICATED. 8. SPRING LOADED GATE: TOP HINGES TO BE TWO PART TYPE SIGN B & C
3 3 7 5
1260 1200 HIGH SPRING LOADED GATE
CLEAR
GENERAL NOTES:
2. 3.
SIGN E 1200 HIGH WELDMESH FENCE

3 5 1 0
8 1 0
SIGN E
1 0 0 0
1200 HIGH WELDMESH FENCE
1600 CLEAR
1600 CLEAR
400
( SI GNATURE)
390
1 7 0 0 3 0 0
WARNING:TGSI 600 x 1500
WARNING:TGSI
5 1 8 5 1 7 0 0 3 0 0
1000 CLEAR
600 x 1500
1 0 0 0
SIGN D
SIGN D
8 1 0
(DOWNEE H4025 OR EQUIVALENT). BOTTOM HINGES TO BE HINGE PINS TYPE (DOWNEE HP25-SC OR EQUIVALENT). GATE CATCH TO BE PIPE POST CATCH TYPE (DOWNEE PP2540 OR EQUIVALENT) 9. CONCRETE FOOTINGS: CONCRETE FOOTING FOR ALL GATE AND STOP POSTS TO BE 400 DIA. x 600 DEEP. CONCRETE FOOTINGS FOR ALL FENCE POSTS TO 230DIA. x 600 DEEP. BASE PLATES FOR EACH POST TO BE FIXED TO FOOTINGS WITH 4 No. 12 DIA. D12058 DYNA BOLTS OR EQUIVALENT. 10. 11. MOTOR UNIT, GATE AND STOP POST TO BE SUPPLIED IN ACCORDANCE WITH MAGNETIC AUTO CONTROL "MRG METRAIL GATE" SPECIFICATIONS. PART OR ALL PARTS OF THE END POSTS FACING THE RAILS TO BE PAINTED OR MARKED TO PROVIDE A CLEAR LUMINANCE CONTRAST WITH THE BACKGROUND. YELLOW PAINT OR CHEVRON HAZARD MARKING IS DEEMED TO COMPLY WITH THIS REQUIREMENT. 12. ASPHALT PAVING TO BE EXTENDED 100 mm BEYOND MAZE FENCE LINES. MINIMUM DISTANCE SHOULD BE INCREASED TO ALLOW FOR CURVE EFFECTS WHEN THE TRACK RADIUS IS LESS THAN 600 m. 14. CRIB FENCING TO BE OFFSET FROM BOOM BARRIER MAST/FLASHING LIGHT MAST @ 2000 mm MIN. PEDESTRIAN CROSSING MAZE ENCLOSURE FENCING SHALL NOT BE POSITIONED LESS THAN 2 m FROM THE CENTRE LINE OF BOOM BARRIER/FLASHING LIGHT MAST FOUNDATION. 15. 13.
SIGN B & C
3 3 7 5
1226
0 0 5 E 1 T A G
1 1 6 7 5
1 5 0 G A 0 T E
CLEAR
END POST & GATE END PAINTED YELLOW
2 SIGN F -
SIGN F 1800 CLEAR 1290 2080 1600 MIN

REFER TO 1 5 0 0MI N
( BL OCK L ETTERS)
ASPHALT PAVEMENT
REFER TO 1 5 0 0MI N NOTE 3 NOTE 3
CLEAR 1010
OUTSIDE OF RAIL 1800 CLEAR 1800 CLEAR
OUTSIDE OF RAIL
TYPICAL GATED PREFERRED MAZE ENCLOSURE ACTIVE CROSSING SCALE 1:75
TYPICAL GATED ALTERNATE MAZE ENCLOSURE ACTIVE CROSSING SCALE 1:75

1200 HIGH WELDMESH FENCE 2000 CLEAR 1950 ASPHALT PAVEMENT SIGN "G"
SIGNAGE NOTES:
1. 2. REFER TO AS 1743 FOR SIGN DETAILS. REFER TO AS1742.2 APPENDIX C FOR ILLUMINATION AND REFLECTORIZATION REQUIREMENTS FOR SIGNS.
X TRACKS
EMERGENCY EXIT CYCLISTS DISMOUNT PLEASE PUSH GATE
5 2 5
2025
X TRACKS LOOK BOTH
DO NOT CROSS WHILE LIGHTS ARE FLASHING OR ALARM SOUNDING
1 9 0 0
WAYS
1 3 5 0
SIGN A OR B
SIGN A
X DENOTES NUMBER OF TRACKS
SIGN B
X DENOTES NUMBER OF TRACKS
SIGN C
2250
1700 CLEAR
SIGN D
1 8 2 5
1800 CLEAR
2150
1 3 5 0
SIGN C
EMERGENCY
5 2 5
CROSSING FAULTS PHONE 1800 XXX XXX QUOTE XXXXX
EXIT
NO
REFER TO
SIGN G SIGN F (RH SHOWN)
WARNING:TGSI
NOTE 3
1 5 0 0MI N
THOROUGHFARE
600 x 1500
X DENOTES DETAIL TO BE PROVIDED
SIGN E
OUTSIDE OF RAIL
$ NAM E$
1800 CLEAR
TYPICAL PEDESTRIAN MAZE ENCLOSURE PASSIVE CROSSING SCALE 1:75

Consultant
$ TI M E$ This drawing has been prepared by, or compiled from information provided by, persons other than Victrack. To the maximum extent permissible by law, Victrack takes no responsibility for, and makes no representations in relation to, the completeness, accuracy or quality of any information contained in this drawing. Each user of this drawing releases Victrack from all and any loss, damage, cost, expense or liability in relation to the use of, or any reliance on, this drawing or the information contained in it. All written dimensions take precedence over scaled dimensions. $ DATE$
IN METRO AREAS USE NUMBER IN COUNTRY AREAS USE NUMBER
1800 001 050. 1800 013 007. NUMBERS TO BE VERIFIED WITH THE INFRASTRUCTURE MANAGER

PEDESTRIAN CROSSING GENERAL ARRANGEMENTS
coffey
Franchisee / Lessee
State Government
rail
03 of 06
Revised By
In Serv
Rev.
Date
Description
Department of
Transport
STD_C0001
$FILE$
( DATE)
50 x 50 x 1.6 GALV. SHS FENCE POST 200 200 x 200 x10mm GALVANISED MILD STEEL PLATE 25 89 x 89 x 6 SHS GATE POST 89 x 89 x 6 SHS GATE POST 200 x 200 x10mm GALVANISED MILD STEEL PLATE 200 25 89 x 89 x 6 SHS GATE POST 353 MODIFIED TO ALLOW MOTOR ARM TO OPERATE
GATE
4 0 8
GATE
4 0 8
50 x 50 x 1.6 GALV. SHS FENCE POST
PROTECTIVE POST TO
( SI GNATURE)
DRILL & TAP 3 M6 HOLES IN GATE MOTOR BRACKET & FENCE DRILL & TAP 4 M6 HOLES IN FENCE &
PROTECTIVE POST TO BE INCLUDED WITH MOTOR ASSEMBLY
BE INCLUDED WITH MOTOR ASSEMBLY
50 x 50 x 1.6 GALV. SHS FENCE POST 209 REFER SECTION A 209
GATE MECHANISM
GATE MECHANISM
DETAIL
DETAIL
( BL OCK L ETTERS)
TRIM WELDMESH FENCE TO NOTE: MOTOR UNIT, GATE AND STOP POST TO BE SUPPLIED IN ACCORDANCE WITH MAGNETIC AUTO CONTROL MRG METRAIL GATE SPECIFICATIONS. ALLOW MOTOR ARM TO OPERATE
REFER TO NOTE 3. FOR FOOTING SIZE
SECTION
A REFER DETAIL 1
90
1600 90
NOTE: GATE OMITTED FOR

CLOSED POSITION
9 0
665
70
CLARITY
5 5
1 5 5
9 0
2 2 0 3 4 0
3 2
450 340
90 1500
1 0 0
1 6 0 0
3 5 0
OPEN POSI TI ON
5 2 5
0 0 . 0 9 R O F D E R R E F E R P N G I S E D
GENERAL NOTES:
1.
1 1 0 1 2 0 0 1 5
70 EMERGENCY ESCAPES TO HAVE 1000 GATE SPRING LOADED TO BE NORMALLY CLOSED AND OPEN ONLY IN DIRECTION INDICATED. 2. SPRING LOADED GATE: TOP HINGES TO BE TWO PART TYPE (DOWNEE H4025 OR EQUIVALENT). BOTTOM HINGES TO BE HINGE PINS TYPE (DOWNEE HP25-SC EQUIVALENT). GATE CATCH TO BE PIPE POST CATCH TYPE (DOWNEE PP2540 OR EQUIVALENT) SCALE 1:10
$ NAM E$
3.
CONCRETE FOOTINGS: CONCRETE FOOTING FOR ALL GATE AND STOP POSTS TO BE 400 DIA. x 600 DEEP. CONCRETE FOOTINGS FOR ALL FENCE POSTS TO 230DIA. x 600 DEEP. BASE PLATES FOR EACH POST TO BE FIXED TO FOOTINGS WITH 4 No. 12 DIA. D12058 DYNA BOLTS OR EQUIVALENT.
SCALE 1:15 4.
MOTOR UNIT, GATE AND STOP POST TO BE SUPPLIED IN ACCORDANCE WITH MAGNETIC AUTO CONTROL MRG METRAIL GATE SPECIFICATIONS.
Consultant
$ TI M E$
coffey
Franchisee / Lessee
State Government
rail

PEDESTRIAN CROSSING ASSEMBLY DETAILS OF PEDESTRIAN CROSSING EQUIPMENT
04 of 06
$ DATE$
Revised By
In Serv
Rev.
Date
Description
Department of
Transport
STD_C0001
$FILE$
( DATE)
200x75 - 1800 LONG TREATED REFER TO SHEET 2 FOR FENCE POST SPACING BOLTS PER SLEEPER PINE SLEEPER
THE STEEL POST RETAINING WALL IS INDICATIVE OF A PREFERRED 1800 MAX 200x75 - 1800 LONG (MAX) 100 UC15 - 1200 LONG STEEL POSTS
( SI GNATURE)
ARRANGEMENT. THE FOLLOWING MUST BE CONSIDERED FOR THE DESIGN OF A STEEL POST RETAINING WALL: FOUNDATION SOIL CONDITIONS BACKFILL MATERIAL QUALITY AND COMPACTION DESIGN SURCHARGE POSTS SITE PROFILE IN FRONT OF AND BEHIND THE WALL
TREATED PINE SLEEPER
AT 1800 CENTRES (MAX)
SCALE 1:20
MI N EM BEDM ENT 7 0 0
PLAN OF TYPICAL STEEL POST RETAINING WALL
ADDITIONAL LOADINGS EG. HANDRAIL/FENCE
5 0 0 M AX HEI GHT
100 UC15 - 1200 LONG GALVANISED STEEL POSTS AT 1800 CENTRES (MAX)
2450 MAX. 50mm x 1.6 mm GALV. SHS POSTS (TYP) 50
ROLLED TOP AND BOTTOM GALVANISED ARC WELDMESH FENCING OR EQUIVALENT
THESE CRITERIA WILL CONFIRM DIMENSIONS AND ARRANGEMENTS WHEN THE DESIGN IS UNDERTAKEN BY A SUITABLY QUALIFIED ENGINEER.
MIN 775 DEEP
( BL OCK L ETTERS)
300
1
1 2 0 0
STEEL POST RETAINING WALL

1 2 9 5
SCALE 1:20
GENERAL NOTES
1. 2. ALL DIMENSIONS ARE IN MILLIMETRES. UNLESS SHOWN OTHERWISE, FENCE DIMENSIONS ARE TO THE FENCE CENTRELINE OR CENTRE OF FENCE POSTS. 3. WELDMESH FENCING TO BE PROVIDED FOR 30m EACH SIDE OF PEDESTRIAN CROSSING WHERE EXISTING BOUNDARY FENCING HAS BEEN REMOVED.
6 0 0MI N 7 5 M AX
NSL
4 3
MASS CONCRETE
SCALE 1:25 No. 1

FENCE
DESCRIPTION CAP (PRESS ON TYPE) 50mm 8 x 64 HEX GALV. BOLT U TYPE GALV. PANEL CLIP
50mm x 1.6mm GALV. SHS
50mm x 1.6mm
4 2
GALV. SHS
2 40mm THICKNESS SIZE 7mm HOT MIX ASPHALT 4

7 5 4 0
500 1:1.5 CUT BATTER OR AS APPROVED 1.5 1
100
TUFF NUT OR EQUIVALENT SECURITY NUT
PATHWAY
3 B -
3 B PAVEMENT LEVEL
1 1:2 FILL BATTER OR AS APPROVED 2 MIN 75mm THICKNESS CLASS 2 20mm NOM. SIZE CRUSHED ROCK
PLAN
MIN 100 x 25 TIMBER EDGING
$ NAM E$
CORNER PLAN
TYPICAL MINIMUM BATTER SLOPES AND ASPHALT PAVEMENT DETAIL

SCALE 1:75
SECTION DETAIL OF PANEL CONNECTION TO POSTS

SCALE 1:5 SCALE 1:5
B -
Consultant
$ TI M E$
coffey
Franchisee / Lessee
State Government
rail

05 of 06
$ DATE$
Revised By
In Serv
Rev.
Date
Description
Department of
Transport
STD_C0001
$FILE$
1 2 9 5
WELDMESH FENCING
7 5
( DATE)
REFER TO FENCE AND HANDRAIL SCHEDULE FOR HANDRAIL AND CONNECTION MATERIALS. REFER TO NOTE 3. EQUIVALENT. AS REQUIRED. 50 x 1.6 GALV. SHS POSTS (TYP) ROLLED TOP AND BOTTOM GALVANISED ARC
FENCE AND HANDRAIL SCHEDULE

HANDRAIL BRACKET HANDRAIL 16 DIA BAR 48.3 DIA x 2.9 CHS HEAVILY GALVANISED HEAVILY GALVANISED
No. 1 2 3
DESCRIPTION CAP (PRESS ON TYPE) 50mm x 50mm 8 x 64 HEX GALV. BOLT OR EQUIVALENT U TYPE GALV. PANEL CLIP
L MAX
( SI GNATURE)
3 -
TUFF NUT OR EQUIVALENT SECURITY NUT
1 2 0 0
8 6 5MI N -9 0 0 M AX
CFW
5 MIN
80 MIN GREASED TELESCOPING TUBE 33.7 x 4 CHS (GALV) 1
( BL OCK L ETTERS)
PAVEMENT
7 5
LEVEL
7 5
HANDRAIL
6 0 0MI N 7 5 M AX
100 BRACKET
7 5
7 5
RAMP SURFACE GRADE VARIES (REFER TO

HANDRAIL JOINT DETAIILS TYPICAL JOINTS AT 9m CENTRES

SCALE 1:5 MASS CONCRETE 60 CLEAR HANDRAIL : 4mm FILLET WELD TO BRACKET ON SITE. GALVANISING MADE GOOD WITH COLD GALV. INDICATIVE FENCE / HANDRAIL
SCHEDULE)
7 5
P MAX (REFER TO POST SCHEDULE)
CONTINUATION
RAMP FENCE ELEVATION

SCALE 1:25 BRACKET: BAR BENT TO 90 ANGLE. SHOP FILLET WELD TO POST PRIOR TO GALVANISING HANDRAIL 3 300 RAMP GRADE DEGREES MAX PANEL LENGTH (mm) MAX POST SPACING c/c DOMED BUTTON 150 3 G 1 IN 14 1 IN 15 1 IN 16 1 IN 17 1 IN 18 1 IN 19 1 IN 20
$ NAM E$ 8 6 5MI N -9 0 0 M AX
BRACKET: BAR BENT TO 90 ANGLE. SHOP FILLET WELD TO POST PRIOR 2 TO GALVANISING
POST SPACING SCHEDULE C -
L 4.09 3.81 3.58 3.37 3.18 3.01 2.86 1050 1100 1200 1250 1350 1400 1500
P 1100 1150 1250
HANDRAIL
BEND
50 x 1.6 GALV. SHS

S EA M A S E D A R PG M A R
HANDRAIL TURNDOWN 1300 1400 1450 1550 5 THICK
F.S.L.
R.75
OR CONTINUATION
CAPING PLATE
HANDRAIL TURNDOWN DETAIL

SCALE 1:10
PANEL CONNECTION TO POST WITH HANDRAIL AND TURNBACK 3 SCALE 1:5
SECTION
SCALE 1:5
C -
NOTES:
1. 2. 3. USE POST SPACING OF STEEPER GRADE FOR INTERMEDIATE GRADES. MAXIMUM GAP BETWEEN BOTTOM OF THE WELDMESH FENCE AND FINISHED SURFACE IS 75mm HAND RAIL REQUIRED AS PER DSAPT AND AS 1428.2
Consultant
$ TI M E$
7 5 M AX
coffey
Franchisee / Lessee
State Government
rail

06 of 06
$ DATE$
Revised By
In Serv
Rev.
Date
Description
Department of
Transport
STD_C0001
$FILE$

STD C0001

Uploaded by

Copyright:

Available Formats

STD C0001

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

STD C0001

Uploaded by

Copyright:

Available Formats

SYMBOLS

PERMANENT SURVEY MARK SURVEY STATION S&C PIT S&C RELAY

13. STEPS & HANDRAILS

GRATED PIT DRAINAGE PIT SEWER PIT TREE

MIN. 150 DOMED TREATED PINE

HP GAS - ABOVE GROUND

Ahmed Dwidar Shane Cooper

RAILWAY TRACK AND CIVIL STANDARD DRAWING

Approved H.R.E. Drawing Number

Approval Date 16/12/11 Revision

Designed Checked Ind. Rev. Approv.

14.2 (a) RUBBER PANEL PAVEMENT J

OUTSIDE RAIL OUTSIDE RAIL

REFER TO DETAIL 1 "pedeSTRAIL" RUBBER UNITS OR APPROVED EQUIVALENT

EPFLEX RAILSEAL EPFLEX RAILSEAL FIELD SIDE 60 60 270 GAUGE SIDE

EPLOCK CLIP EXISTING SLEEPER

RAILWAY TRACK AND CIVIL STANDARD DRAWING

Drawn By B.C. Checked By A.C. Approved H.R.E. Drawing Number

Designed By B.C. Ind. Review

Approval Date 16/12/11 Revision

Designed Checked Ind. Rev. Approv.

SIGN "G" 1830

1260 1200 HIGH SPRING LOADED GATE

SIGN E 1200 HIGH WELDMESH FENCE

1200 HIGH WELDMESH FENCE

1200 HIGH WELDMESH FENCE

WARNING:TGSI 600 x 1500

END POST & GATE END PAINTED YELLOW

SIGN F 1800 CLEAR 1290 2080 1600 MIN

OUTSIDE OF RAIL 1800 CLEAR 1800 CLEAR

TYPICAL GATED PREFERRED MAZE ENCLOSURE ACTIVE CROSSING SCALE 1:75

TYPICAL GATED ALTERNATE MAZE ENCLOSURE ACTIVE CROSSING SCALE 1:75

EMERGENCY EXIT CYCLISTS DISMOUNT PLEASE PUSH GATE

X TRACKS LOOK BOTH

DO NOT CROSS WHILE LIGHTS ARE FLASHING OR ALARM SOUNDING

CROSSING FAULTS PHONE 1800 XXX XXX QUOTE XXXXX

SIGN G SIGN F (RH SHOWN)

X DENOTES DETAIL TO BE PROVIDED

TYPICAL PEDESTRIAN MAZE ENCLOSURE PASSIVE CROSSING SCALE 1:75

IN METRO AREAS USE NUMBER IN COUNTRY AREAS USE NUMBER

RAILWAY TRACK AND CIVIL STANDARD DRAWING

Drawn By B.C. Checked By A.C. Approved H.R.E. Drawing Number

Designed By B.C. Ind. Review

Approval Date 16/12/11 Revision

Designed Checked Ind. Rev. Approv.

50 x 50 x 1.6 GALV. SHS FENCE POST

PROTECTIVE POST TO BE INCLUDED WITH MOTOR ASSEMBLY

BE INCLUDED WITH MOTOR ASSEMBLY

50 x 50 x 1.6 GALV. SHS FENCE POST 209 REFER SECTION A 209

1200 HIGH WELDMESH FENCE

1200 HIGH WELDMESH FENCE

REFER TO NOTE 3. FOR FOOTING SIZE

NOTE: GATE OMITTED FOR

RAILWAY TRACK AND CIVIL STANDARD DRAWING

Drawn By B.C. Checked By A.C. Approved H.R.E. Drawing Number

Designed By B.C. Ind. Review

Approval Date 16/12/11 Revision

Designed Checked Ind. Rev. Approv.