Scribd
Upload
60 views6 pages

How To Configure DH+ Between Panelview Plus and Slc504 Using 2711P-Rn6

1. Create an application in the SLC504 processor to communicate with PanelView Plus over Ethernet. Download the application to the processor. 2. Create a PanelView Plus application and configure the Ethernet communication between the PC and SLC504. Test a numeric display and input. 3. Set up the Ethernet communication between PanelView Plus and SLC504 and download the application to PanelView Plus using a transfer utility over the Ethernet connection. Connect PanelView Plus and SLC504 using an Ethernet cable to run the application.

Uploaded by

for_c
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
60 views6 pages

How To Configure DH+ Between Panelview Plus and Slc504 Using 2711P-Rn6

1. Create an application in the SLC504 processor to communicate with PanelView Plus over Ethernet. Download the application to the processor. 2. Create a PanelView Plus application and configure the Ethernet communication between the PC and SLC504. Test a numeric display and input. 3. Set up the Ethernet communication between PanelView Plus and SLC504 and download the application to PanelView Plus using a transfer utility over the Ethernet connection. Connect PanelView Plus and SLC504 using an Ethernet cable to run the application.

Uploaded by

for_c
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 6

How to configure DH+ between PanelView Plus and SLC504 using 2711P !

"#
If you dont have 1784-PKTX card or PCMK card, you are still a le to confi!ure Panel"ie# Plus tal$in! to %&C'(4 thru )*+ net#or$, *ere is the e-a./le,

1,Create a 0%&o!i-'(( a//lication the /rocessor - &in$ %&C'(4 to your PC usin! 123)41-1 - Create a 0%&o!i-'(( a//lication, #e #ill 5ust use 677( address, )o#nload the a//lication to the /rocessor, - &eave %&C'(4 in runnin!, 8o to 0%&in- and delete 123)41-1 9,Create a 0%"ie# M: a//lication - &in$ PC to %&C'(4 usin! 0%9;9 cross-over ca le - &aunch 0%"ie# M: < )ou le clic$ =Co..unication %etu/> < Create a ne# confi!uration, - ?nder &ocal ta , add )41 driver and confi!ure it as follo#in! screens

- Create a shortcut and /oint to the %&C'(4 under )41 driver

Create a ne# dis/lay, /ut a nu.eric dis/lay and a nu.eric in/ut o 5ects on it, Ma$e sure to connect 677(, %ave the dis/lay as =Test>

- Test the dis/lay and .a$e sure you can in/ut and dis/lay 677( data

- ?nder Start, do follo#in! settin!s7

- 2ac$ Co..unication setu/ screen < Tar!et ta < 1dd driver and choose )*+ @1784-PKTX, 9711-06A, 9711068B < CK

- )river selection is follo#ed y a dialo! that lets you set the drivers 6a.e, the ada/ters %tation I) and Du./er I), and the net#or$ 2aud rate7

This sa.e confi!uration dialo! can e .odified later, y doin! a 0i!ht clic$ on the )river /ro/erties, - 6o# add the /rocessor eneath that ada/ter7 0i!ht clic$ )*Plus, )*+ < 1dd device < Choose relevant /rocessor < CK

- 0e-/oint the shortcut na.e to the /rocessor a!ain, 2e sure, this ti.e you define the =/ointer> in Tar!et ta

;, )o#nload a//lication to Panel"ie# Plus - ?se a strai!ht thru ca le to lin$ PC and Panel"ie# Plus - ?nder co..unication setu/ < &ocal Ta < 0i!ht clic$ )41 < Pro/erties

- *it CK and you should e a le to see Panel"ie# Plus @a PC iconB

Create a runti.e a//lication ?se Transfer ?tility to do#nload the a//lication to P"P thru )41 drive

Connect Panel"ie# Plus and %&C'(4 usin! )*+ ca le Ehen do#nloadin! finishes, load the a//lication and run it, PanelView Plus 0IC ;, 2lue 9, %hield 1, Clear SLC504 )*+ 1, 2lue %hield 9, Clear

4,Ca le connection )*+ ;, Clear 9, %hield 1, 2lue

You might also like