MXM/TM FAULT CODES Codes common to all MXM/TMs Digital Instrument Cluster Codes (EIC) Error Code 1 - Engine

Oil Pressure Sender Short Or Open Circuit Error Code 2 - Engine Oil Pressure Sender Short To +Ve Voltage Error Code 3 - Fuel Tank Level Sender Short To Ground Error Code 4 - Fuel Tank Level Sender Open Circuit Or Short To +Ve Voltage Error Code 5 - Wheel Speed Sender Short Circuit Error Code 6 - Wheel Speed Sender Open Circuit Error Code 7 - Coolant Temperature Sender Short Circuit Error Code 8 - EDC Serial Link Failure. Communications Error Error Code 9 - Transmission Serial Link Failure. Communications Error Error Code 10 - Memory Retention Error Of Battery Calibration Constant Error Code 11 -Memory Retention Error Of Operator Setting For Slip Alarm, Slip Zero Reference Constant, Implement Width And Service Hours Error Code 12 -Coolant Temperature Sender Open Circuit Or Shorted To A + Ve Voltage Error Code 13 - Engine Shut Down Output Short To A +Ve Voltage Instrument Cluster Inoperative Electronic Hitch Codes (CFPS or GCM1) Error code HL - Height limit incorrectly set to perform auto calibration Error Code 2 - Poor Or No Signal From Tractor Performance Monitor Radar Error Code 3 - Radar (Ground Speed) Greater Than Wheel Speed Error Code 4 - Wheel Speed Greater Than Maximum Speed Of Tractor Error Code 5 - Wheel Speed Zero When Radar Is Indicating Ground Speed Error Code 6 - Slip Control Voltage Low (Short Or Open Circuit) Error Code 7 - Slip Control Voltage High (Damaged Potentiometer Or Short To +12 Volts) Error Code 8 - Raise/Work Switch Failure Error Code 9 - Both External Lift/Lower Fender Switches Are Being Operated Simultaneously Error Code 10 - Height Limit Control Voltage Low (Short Or Open Circuit) Error Code 11 - Height Limit Control Voltage High (Damaged Potentiometer Or Short To +12 Volts) Error Code 12 - Drop Rate Control Voltage Low (Short Or Open Circuit) Error Code 13 - Drop Rate Control Voltage High (Damaged Potentiometer Or Short To +12 Volts) Error Code 14 -Open Circuit Connection To Load Sensing Pin, Short Circuit To Ground Or Failed Load Sensing Pin Error Code 15 -Load Sensing Pin Short Circuit To +12 Volts, Failed Or Corroded Load Sensing Pin Error Code 16 -Open Circuit Connection To Load Sensing Pin, Short Circuit To Ground Or Failed Load Sensing Pin Error Code 17 -Load Sensing Pin Short Circuit To +12 Volts, Failed Or Corroded Load Sensing Pin

Error Code 18 - Both Load Sensing Pins Disconnected Error Code 19 -Pin Reference Voltage Less Than 8 Volts (Short Or Open Circuit) Error Code 20 -Pin Reference Voltage Greater Than 8 Volts (Short To +12 Volts) Error Code 21 -Draft Sensitivity Control Voltage Low (Short Or Open Circuit) Error Code 22 -Draft Sensitivity Control Voltage High (Damaged Potentiometer Or Short To +12 Volts) Error Code 23 - Control Panel Disconnected Error Code 24 - Perform Hydraulic Lift Calibration Error Code 25 -Position Lever Potentiometer Control Voltage Low (Short Or Open Circuit) Error Code 26 -Position Lever Potentiometer Control Voltage High (Damaged Potentiometer Or Short To +12 Volts) Error Code 27 -Lift Arm Position Sensing Control Voltage Low (Short Or Open Circuit) Error Code 28 -Lift Arm Position Sensing Control Voltage High (Damaged Potentiometer Or Short To +12 Volts) Error Code 29 - Hydraulic Control Valve Disconnected Error Code 30 - Signal Ground Open Circuit Error Code 31 - Chassis Harness Disconnected Error Code 32 - Draft Load Potentiometer Shorted To +12v Error Code 33 -Draft Control Potentiometer Open Circuit Or Short To Ground Error Code 49 - Wheel Speed Sensor Open Or Short Circuit Error Code 53 - Microprocessor 5 Volt Reference Shorted To +12 Volts Error Code 54 - Microprocessor 5 Volt Reference Shorted To Ground Error Code 57 - EDC Microprocessor Failure Error Code 59 - Microprocessor Reference Voltage Open Circuit Error Code 63 - EDC Hydraulic Valve Lower Solenoid Open Circuit Error Code 64 - EDC Hydraulic Valve Raise Solenoid Open Circuit Error Code 65 - EDC Hydraulic Valve Lower Solenoid Short Circuit Error Code 66 - EDC Hydraulic Valve Raise Solenoid Short Circuit Error Code 67 - EDC Hydraulic Valve Supply Voltage Too Low Error Code 69 - Control Lever EDC Raise/Lower Switch Failure Front Suspended Axle Codes (GCM1 or XCM) Error Code L01 - Lockout Valve Raising Solenoid Not Working Error Code L02 - Raising Solenoid Not Working Error Code L03 - Lowering Solenoid Not Working Error Code L04 -Front Axle Potentiometer Threshold Is Higher Than The Set Limit Error Code L05 -Front Axle Potentiometer Threshold Is Lower Than The Set Limit Error Code L06 - The Suspension Is Not Calibrated Error Code L07 -Front Axle Weight Has Been Reduced But The Suspension Is Unable To Reset Nominal Height Error Code L08 -Front Axle Weight Has Been Increased But The Suspension Is Unable To Reset Nominal Height Error Code L09 - Lockout Valve Lower Solenoid Not Working PTO Codes Common to the MXM/TM120-MXM/TM155 (EMU)

NOTE: If P34 and P40 appear, see Knowledge for keywords Error codes P34 and P40 display and follow the resolution. Error Code P01 - Rear PTO Brake Solenoid Stuck Off Error Code P02 - Rear PTO Brake Solenoid Stuck On Error Code P03 - Rear PTO Brake Output Open Circuit Error Code P04 Rear PTO Brake Driver Over Temperature Error Code P05 Rear PTO Brake Switch open circuit Error Code P06 - Rear PTO Not Calibrated Error Code P07 Rear PTO Solenoid Over Current Error Code P08 - Rear PTO Solenoid Stuck Off Error Code P15 - Differential Lock Solenoid Stuck Off Error Code P16 - Differential Lock Solenoid Stuck On Error Code P17 - Differential Lock Output Open Circuit Error Code P18 - Differential Lock Driver Over Temperature Error Code P21 - 4wd Solenoid Stuck Off Error Code P22 - 4wd Solenoid Stuck On Error Code P23 - 4wd Output Open Circuit Error Code P24 - 4wd Driver Over Temperature Error Code P27 - PTO Speed Sensor Open Circuit Error Code P31 - Steering Sensor Out Of Range - (Maximum Voltage) Error Code P32 - Steering Sensor Out Of Range - (Minimum Voltage) Error Code P33 - Rear PTO Cab Switch Momentary Contact Open Error Code P34 -Fender Mounted Rear PTO Switch Open Circuit Or Short To Ground Error Code P35 -Fender Mounted Rear PTO Switch Input Short To +12v Or Short Across Fender Switch Wires Error Code P36 - Rear PTO Failure To Start - Relay Or Switch Wiring Fault Error Code P37 -Rear PTO Cab Switch Momentary Contact Stuck Closed (Longer Than 30 Seconds) Error Code P38 -Cab And Fender Rear PTO Controls Operated Within 2 Seconds Of Each Other Error Code P39 -Incorrect Voltage On Fender Mounted Rear PTO Switch Input (If Fitted) Error Code P40 - PTO Relay Short To +12v Or An Open Circuit Error Code P41 - PTO Fender Switch Relay Short To Ground Common Test Procedure For All Of The Switch Circuits Connecting To Ground Active Fan Beep Codes Common to the MXM/TM120-MXM/TM155 (SCM) SWB Active Fan codes (number of short tones-do NOT count the first tone) Search Knowledge for keywords Visctronic fan troubleshooting information requested and follow the resolution for the retrieval procedure. Error Code 1 - Transmission oil sensor fault. Error Code 2 - Engine coolant sensor fault. Error Code 3 - Transmission oil temperature implausible (compared to engine coolant temperature).

Error Code 4 - Fan speed out of range. Error Code 5 - Maximum fan speed low (maximum fan speed demanded but not achieved). Error Code 6 - +5V reference error. Error Code 7 - Fan speed output signal error. Semi Powershift MXM/TM120-MXM/TM155 Calibration Codes (all controllers) Error Code CF - Calibration Procedure Completed Successfully Error Code CH - Oil Temperature Above 105 Degrees Centigrade Error Code CL - Oil Temperature Between 10 and 19 Degrees Centigrade Error Code U01 - Front Axle Potentiometer Open Circuit Error Code U02 -Front Axle Potentiometer Threshold Is Higher Than The Set Limit Error Code U03 -Front Axle Potentiometer Short Circuit Auto Calibration Procedure Will Not Work Error Code U04 -Front Axle Potentiometer Threshold Is Lower Than The Set Limit Error Code U05 -Front Suspension Is Not Reaching Minimum And Maximum Position During The Auto Calibration Procedure Error Code U07 -Suspension Is Stationary During The Raise Command In The Auto Calibration Procedure Error Code U08 -Suspension Is Unable To Reach Maximum Height Within 20 Seconds Error Code U09 -Suspension Is Stationary During The Lowering Command In The Auto Calibration Procedure Error Code U10 -Suspension Is Unable To Reach The Minimum Height Within 25 Seconds Error Code U11 - Unable To Calibrate The Suspension Error Code U12 -Auto Calibration Procedure Stopped/Vehicle Not Stationary Error Code U19 - Oil Temperature Below 10 Degrees Centigrade Error Code U21 - Engine RPM Too Low Error Code U22 - Engine RPM Too High Error Code U23 - Shuttle Lever In Neutral Error Code U26 - Clutch Pedal Not Released Error Code U31 - Output Speed Sensed - Tractor Moving Error Code U33 - Hand Brake Not Applied Error Code U34 - Seat Switch Not Activated Error Code U36 - Maximum Allowed Clutch Calibration Value Exceeded Error Code U37 - Engine RPM Dropped Too Soon Error Code U38 - High / Low synchroniser calibration values out of tolerance (Forward) Error Code U81 - No Medium/Reverse Range Synchronizer Movement Sensed Error Code U82 - No Low/High Range Synchronizer Movement Sensed Error Code U83 - Synchronizer Potentiometer Connectors Swapped Error Code U84 - Reverse And High Range Synchronizer Solenoid Connectors Swapped Error Code U85 - Medium And Low Range Synchronizer Solenoid Connectors Swapped Error Code U86 - Medium/Reverse Range Synchronizer Neutral Error Error Code U87 - Low/High Range Synchronizer Neutral Error Error Code U88 - Medium/Reverse Range Synchronizer Calibration Values Out Of Tolerance

Error Code U89 - Low/High Range Synchronizer Calibration Values Out Of Tolerance Transmission Codes (GCM2 or TCM) (Semi Powershift) Error Code CP - Depress The Clutch Pedal To Re-Enable The Transmission Error Code F02 - High/Low Synchronizer Not Calibrated Or A Bad Calibration Error Code F03 - Medium/Reverse Synchronizer Not Calibrated Or A Bad Calibration Error Code F11 - Clutch Potentiometer Voltage Below Valid Range Error Code F12 - Clutch Potentiometer Voltage Above Valid Range Error Code F13 - Upshift And Downshift Switches Both Closed Error Code F1A - Clutch A Solenoid Open Circuit Or Short To Ground Error Code F1B - Clutch B Solenoid Open Circuit Or Short To Ground Error Code F1C - Clutch C Solenoid Open Circuit Or Short To Ground Error Code F1D - Clutch D Solenoid Open Circuit Or Short To Ground Error Code F1E - Clutch E Solenoid Open Circuit Or Short To Ground Error Code F1H - High Range Solenoid Open Circuit Or Short To Ground Error Code F1L - Low Range Solenoid Open Circuit Or Short To Ground Error Code F1P - Reverse Range Solenoid Open Circuit Or Short To Ground Error Code F1U - Medium Range Solenoid Open Circuit Or Short To Ground Error Code F20 - Range Shift Synchronizer Did Not Engage Error Code F21 - Transmission Extension Harness To Main Harness Disconnected Error Code F22 - Range Shift Synchronizer Did Not Disengage Error Code F23 - Creeper Engaged Speed Or Gear To High Error Code F24 - All Clutches And Synchronizers Require Calibration Error Code F27 - Engine RPM Signal Not Present Error Code F2A - Clutch A Solenoid Over Voltage Error Code F2B - Clutch B Solenoid Over Voltage Error Code F2C - Clutch C Solenoid Over Voltage Error Code F2D - Clutch D Solenoid Over Voltage Error Code F2E - Clutch E Solenoid Over Voltage Error Code F31 - Range Shift Synchronizer Did Not Engage During Shuttle Shift Error Code F32 - High Range Synchronizer Did Not Engage During Start Up Sequence, Within Specified Time (This Is Part Of A System Test During Start Up) Error Code F33 - Synchronizer Did Not Disengage Error Code F34 - Synchronizer Did Not Disengage After Start Up Power Up (Part Of Start Up Sequence) Error Code F35 - Synchronizer Did Not Engage Previous Range After Error Code F20 Or F22 Error Code F36 - Synchronizer Disengaged Without Driver Initiation Error Code F37 - Clutch Disconnect Switch Open Circuit Error Code F38 - Disabled Range Selected By The Operator Error Code F40 - Medium/Reverse Range Synchronizer Potentiometer Over Voltage Error Code F41 - Medium/Reverse Range Synchronizer Potentiometer Under Voltage Error Code F42 - Low/High Range Synchronizer Potentiometer Over Voltage Error Code F43 - Low/High Range Synchronizer Potentiometer Under Voltage Error Code F44 - Medium/Reverse Range Synchronizer Potentiometer Out Of Calibrated Range

Error Code F45 - Low/High Range Synchronizer Potentiometer Out Of Calibrated Range Error Code F47 - Clutch Disconnect Switch Misadjusted High Error Code F48 - Clutch Disconnect Switch Short Circuit Error Code F49 - Transmission Output Speed Sensor Open Circuit Error Code F50 - Transmission Output Speed Sensor Short To Ground Error Code F51 - Temperature Sender Open Circuit Error Code F52 - Temperature Sender Short To Ground Error Code F53 - +5 Volt Reference Voltage Too High Error Code F54 - +5 Volt Reference Voltage Too Low Error Code F55 - +8 Volt Reference Voltage Too High Error Code F56 - +8 Volt Reference Voltage Too Low Error Code F59 - Forward/Neutral/Reverse Switch Disagreement (More Than One Switch Is Engaged) Error Code F60 - Upshift Switch Input Voltage Low Error Code F61 - Upshift Switch Input Voltage High Error Code F62 - Downshift Switch Input Voltage Low Error Code F63 - Downshift Switch Input Voltage High Error Code F64 - Range shift Switch Input Voltage Low Error Code F65 - Range shift Switch Input Voltage High Error Code F66 - Shuttle Lever Forward Switch Input Voltage Low Error Code F67 - Shuttle Lever Forward Switch Input Voltage High Error Code F68 - Shuttle Lever Reverse Switch Input Voltage Low Error Code F69 - Shuttle Lever Reverse Switch Input Voltage High Error Code F73 - Transmission Mid Speed Sensor Open Circuit Error Code F74 - Transmission Mid Speed Sensor Short To Ground Error Code F75 - Swapped Mid And Output Speed Sensors Error Code F77 - No Signal From The Output Speed Sensor Error Code F78 - No Signal From The Transmission Mid Speed Sensor Error Code F79 - Engine RPM Exceeds 3000 RPM Error Code F80 - Transmission Output Rev/Min Too High For The Selected Gear Error Code F81 - Clutch Slipping Error Code FCA - Clutch A Not Calibrated Error Code FCB - Clutch B Not Calibrated Error Code FCC - Clutch C Not Calibrated Error Code FCD - Clutch D Not Calibrated Error Code FCE - Clutch E Not Calibrated FULL POWERSHIFT MXM/TM120-MXM/TM155 Calibration Codes (all controllers) Error Code CF - Calibration Procedure Completed Successfully Error Code CH - Oil Temperature Above 105 Degrees Centigrade Error Code CL - Oil Temperature Between 10 and 59 Degrees Centigrade Error Code U01 - Front Axle Potentiometer Open Circuit Error Code U02 -Front Axle Potentiometer Threshold Is Higher Than The Set Limit

Error Code U03 -Front Axle Potentiometer Short Circuit Auto Calibration Procedure Will Not Work Error Code U04 -Front Axle Potentiometer Threshold Is Lower Than The Set Limit Error Code U05 -Front Suspension Is Not Reaching Minimum And Maximum Position During The Auto Calibration Procedure Error Code U07 -Suspension Is Stationary During The Raise Command In The Auto Calibration Procedure Error Code U08 -Suspension Is Unable To Reach Maximum Height Within 20 Seconds Error Code U09 -Suspension Is Stationary During The Lowering Command In The Auto Calibration Procedure Error Code U10 -Suspension Is Unable To Reach The Minimum Height Within 25 Seconds Error Code U11 - Unable To Calibrate The Suspension Error Code U12 -Auto Calibration Procedure Stopped/Vehicle Not Stationary Error Code U19 - Oil Temperature Below 60 Degrees Centigrade Error Code U21 - Engine RPM Too Low Error Code U22 - Engine RPM Too High Error Code U23 - Shuttle Lever In Neutral Error Code U26 - Clutch Pedal Not Released Error Code U31 - Output Speed Sensed - Tractor Moving Error Code U33 - Hand Brake Not Applied Error Code U34 - Seat Switch Not Activated Error Code U36 - Maximum Allowed Clutch Calibration Value Exceeded Error Code U37 - Engine RPM Dropped Too Soon Transmission Codes (CFPS) Error Code CP - Depress The Clutch Pedal To Re-Enable The Transmission Error Code F11 - Clutch Potentiometer Voltage Below Valid Range Error Code F12 - Clutch Potentiometer Voltage Above Valid Range Error Code F13 - Open Circuit From Fuse 13 Error Code F1F - Configuration error (download the latest software) Error Code F21 -Transmission Extension Harness To Main Harness Disconnected Error Code F23 Creeper Engaged In A Gear Higher Than 10th Error Code F24 - All Clutches And Synchronizers Require Calibration Error Code F27 ERPM Signal Not Present Error Code F37 - Clutch Disconnect Switch Open Circuit Error Code F38 - Reverse Not Allowed Error Code F47 - Clutch Disconnect Switch Misadjusted High Error Code F48 - Clutch Disconnect Switch Short Circuit Error Code F49 - Transmission Output Speed Sensor Open Circuit Error Code F50 - Transmission Output Sensor Short To Ground Error Code F51 - Temperature Sender Open Circuit Error Code F52 - Temperature Sender Short To Ground Error Code F53 - +5 Volt Reference Voltage Too High Error Code F54 - +5 Volt Reference Voltage Too Low

Error Code F59 -Forward/Neutral/Reverse Switch Disagreement (More Than One Switch Is Engaged) Error Code F60 - Upshift Switch Input Voltage Low Error Code F61 - Upshift Switch Input Voltage High Error Code F62 - Downshift Switch Input Voltage Low Error Code F63 - Downshift Switch Input Voltage High Error Code F64 -Forward Pressure Switch Open Circuit Or Short To Ground Error Code F65 -Reverse Pressure Switch Open Circuit Or Short To Ground Error Code F66 - Shuttle Lever Forward Switch Input Voltage Low Error Code F67 - Shuttle Lever Forward Switch Input Voltage High Error Code F68 - Shuttle Lever Reverse Switch Input Voltage Low Error Code F69 - Shuttle Lever Reverse Switch Input Voltage High Error Code F70 - Torque Damper Fault Error Code F71 - Engine Torque/RPM Sensor Open Circuit Error Code F72 - Engine Torque/RPM Sensor Short To Ground Error Code F73 - Transmission Mid Speed Sensor Open Circuit Error Code F74 - Transmission Mid Speed Sensor Short To Ground Error Code F75 - Swapped Mid And Output Speed Sensors Error Code F76 -Swapped Engine Torque/RPM Sensor With Either The Mid Or Output Speed Sensors Error Code F77 - No Signal From The Output Speed Sensor Error Code F78 - No Signal From The Transmission Mid Speed Sensor Error Code F79 - Engine RPM Exceeds 3000 Rev/Min Error Code F80 -Transmission Output Rev/Min Too High For The Selected Gear Error Code F81 - Clutch Slipping Error Code F82 -Foot Throttle Position Sensor Potentiometer Short Circuit To +8 Volts Or +12 Volts Error Code F83 -Foot Throttle Sensor Potentiometer Open Circuit Or Short To Ground Error Code F84 -Pressure Indicated On Forward Clutch Pressure Switches When The Clutch Solenoids Are Off Error Code F85 -Pressure Indicated On Reverse Clutch Pressure Switch When The Clutch Solenoids Are Off Error Code F91 - Display Of Gears Controller (CAN Dog) Not Present Error Code FA1 -Low Range Clutch Solenoid Open Circuit Or Short To Ground Error Code FA2 -Medium Range Clutch Solenoid Open Circuit Or Short To Ground Error Code FA3 -High Range Clutch Solenoid Open Circuit Or Short To Ground Error Code FA4 -Reverse Clutch Solenoid Open Circuit Or Short To Ground Error Code FAA - Clutch A Solenoid Open Circuit Or Short To Ground Error Code FAB - Clutch B Solenoid Open Circuit Or Short To Ground Error Code FAC - Clutch C Solenoid Open Circuit Or Short To Ground Error Code FAD - Clutch D Solenoid Open Circuit Or Short To Ground Error Code FAE - Clutch E Solenoid Open Circuit Or Short To Ground Error Code FAF - PTO Lube Solenoid Open Circuit Or Short To Ground Error Code FB1 - Low Range Clutch Solenoid Over Voltage Error Code FB2 - Medium Range Clutch Solenoid Over Voltage Error Code FB3 - High Range Clutch Solenoid Over Voltage

Error Code FB4 - Reverse Clutch Solenoid Over Voltage Error Code FBA - Clutch A Solenoid Over Voltage Error Code FBB - Clutch B Solenoid Over Voltage Error Code FBC - Clutch C Solenoid Over Voltage Error Code FBD - Clutch D Solenoid Over Voltage Error Code FBE - Clutch E Solenoid Over Voltage Error Code FBF - PTO Lube Solenoid Over Voltage Error Code FC0 - Secondary Controller (CFPS) Is Not Configured Error Code FC1 - Medium Range Clutch Not Calibrated Error Code FC2 - High Range Clutch Not Calibrated Error Code FC3 - Reverse Clutch Not Calibrated Error Code FC9 - Configuration error (download the latest software) Error Code FCA - Clutch A Not Calibrated Error Code FCB - Clutch B Not Calibrated Error Code FCC - Clutch C Not Calibrated Error Code FCD - Clutch D Not Calibrated Error Code FCE - Clutch E Not Calibrated Error Code FCF - Low Range Clutch Not Calibrated Error Code N - Shift To Neutral To Re-Enable The Transmission Full Powershift MXM/TM175 And MXM/TM190 Calibration Codes (all controllers) Error Code CF - Calibration Procedure Completed Successfully Error Code CH - Oil Temperature Above 105 Degrees Centigrade Error Code CL - Oil Temperature Between 10 And 59 Degrees Centigrade Error Code U1 - Flow Control For Lever 1 Set Incorrectly During Calibration Error Code U2 - Flow Control For Lever 2 Set Incorrectly During Calibration Error Code U3 - Flow Control For Lever 3 Set Incorrectly During Calibration Error Code U4 - Flow Control For Lever 4 Set Incorrectly During Calibration Error Code U01 - Front Axle Potentiometer Open Circuit Error Code U02 -Front Axle Potentiometer Threshold Is Higher Than The Set Limit Error Code U03 -Front Axle Potentiometer Short Circuit Auto Calibration Procedure Will Not Work Error Code U04 -Front Axle Potentiometer Threshold Is Lower Than The Set Limit Error Code U05 -Front Suspension Is Not Reaching Minimum And Maximum Position During The Auto Calibration Procedure Error Code U07 -Suspension Is Stationary During The Raise Command In The Auto Calibration Procedure Error Code U08 -Suspension Is Unable To Reach Maximum Height Within 20 Seconds Error Code U09 -Suspension Is Stationary During The Lowering Command In The Auto Calibration Procedure Error Code U10 -Suspension Is Unable To Reach The Minimum Height Within 25 Seconds Error Code U11 - Unable To Calibrate The Suspension Error Code U12 -Auto Calibration Procedure Stopped/Vehicle Not Stationary

Error Code U19 - Oil Temperature Below 10 Degrees Centigrade Error Code U21 - Engine RPM Too Low Error Code U22 - Engine RPM Too High Error Code U23 - Shuttle Lever In Neutral Error Code U26 - Clutch Pedal Not Released Error Code U31 - Output Speed Sensed - Tractor Moving Error Code U33 - Hand Brake Not Applied Error Code U34 - Seat Switch Not Activated Error Code U36 - Maximum Allowed Clutch Calibration Value Exceeded Error Code U37 - Engine RPM Dropped Too Soon Error Code U41 PTO speed detected (PTO brake circuit open or PTO solenoid sticking) Error Code U43 PTO calibration aborted Error Code U45 No PTO shaft movement (PTO circuit open) Error Code U50 - PTO Twist Sensor Not Calibrated Error Code U51 - Unable To Achieve The Required Engine Speed Error Code U52 -Constant Engine RPM (CERPM) Switch Switched More Than 3 Times Error Code U53 - Remote Levers Used When Calibrating Error Code U54 - Steering Used When Calibrating Error Code U55 - PTO Engaged When Calibrating Error Code U56 - Engine Torque/RPM Sensor Open Circuit Error Code U57 - Engine Torque/RPM Sensor Short To Ground Error Code U58 - PTO Twist Sensor Open Circuit Error Code U59 - PTO Twist Sensor Short To Ground Error Code U60 - Out Of Range Calibration Value Transmission Error Codes (CFPS) Error Code CP - Depress The Clutch Pedal To Re-Enable The Transmission Error Code F11 - Clutch Potentiometer Voltage Below Valid Range Error Code F12 - Clutch Potentiometer Voltage Above Valid Range Error Code F13 - Open Circuit From Fuse 13 Error Code F19 -19th Gear Clutch Solenoid Open Circuit Or Short To Ground Error Code F1F - Configuration error (download the latest software) Error Code F20 -19th Gear Clutch Dump Solenoid Open Circuit Or Short To Ground Error Code F21 -Transmission Extension Harness To Main Harness Disconnected Error Code F23 Creeper Engaged In A Gear Higher Than 10th Error Code F24 - All Clutches And Synchronizers Require Calibration Error Code F27 ERPM Signal Not Present Error Code F29 - 19th Gear Clutch Solenoid Over Voltage Error Code F30 - 19th Gear Clutch Dump Solenoid Over Voltage Error Code F37 - Clutch Disconnect Switch Open Circuit Error Code F38 - Reverse Not Allowed Error Code F47 - Clutch Disconnect Switch Misadjusted High Error Code F48 - Clutch Disconnect Switch Short Circuit Error Code F49 - Transmission Output Speed Sensor Open Circuit Error Code F50 - Transmission Output Sensor Short To Ground Error Code F51 - Temperature Sender Open Circuit

Error Code F52 - Temperature Sender Short To Ground Error Code F53 - +5 Volt Reference Voltage Too High Error Code F54 - +5 Volt Reference Voltage Too Low Error Code F59 -Forward/Neutral/Reverse Switch Disagreement (More Than One Switch Is Engaged) Error Code F60 - Upshift Switch Input Voltage Low Error Code F61 - Upshift Switch Input Voltage High Error Code F62 - Downshift Switch Input Voltage Low Error Code F63 - Downshift Switch Input Voltage High Error Code F64 -Forward Pressure Switch Open Circuit Or Short To Ground Error Code F65 - Reverse Pressure Switch Open Circuit Or Short To Ground Error Code F66 - Shuttle Lever Forward Switch Input Voltage Low Error Code F67 - Shuttle Lever Forward Switch Input Voltage High Error Code F68 - Shuttle Lever Reverse Switch Input Voltage Low Error Code F69 - Shuttle Lever Reverse Switch Input Voltage High Error Code F70 - Torque Damper Fault Error Code F71 - Engine Torque/RPM Sensor Open Circuit Error Code F72 - Engine Torque/RPM Sensor Short To Ground Error Code F73 - Transmission Mid Speed Sensor Open Circuit Error Code F74 - Transmission Mid Speed Sensor Short To Ground Error Code F75 - Swapped Mid And Output Speed Sensors Error Code F76 - Swapped Engine Torque/RPM Sensor With Either The Mid Or Output Speed Sensors Error Code F77 - No Signal From The Output Speed Sensor Error Code F78 - No Signal From The Transmission Mid Speed Sensor Error Code F79 - Engine RPM Exceeds 3000 Rev/Min Error Code F80 -Transmission Output Rev/Min Too High For The Selected Gear Error Code F81 - Clutch Slipping Error Code F82 -Foot Throttle Position Sensor Potentiometer Short Circuit To +8 Volts Or +12 Volts Error Code F83 -Foot Throttle Sensor Potentiometer Open Circuit Or Short To Ground Error Code F84 -Pressure Indicated On Forward Clutch Pressure Switches When The Clutch Solenoids Are Off Error Code F85 -Pressure Indicated On Reverse Clutch Pressure Switch When The Clutch Solenoids Are Off Error Code F86 - Creeper Fails To Engage Error Code F87 - Creeper Fails To Disengage Error Code F88 - Creeper Potentiometer Short Circuit To +8 Or +12 Volts Error Code F89 - Creeper Potentiometer Open Circuit Or Short To Ground Error Code F90 - Central Controller (XCM) Not Present or generated by the EST-See Knowledge for F90 Error Code F91 - Display Of Gears Controller (CAN Dog) Not Present Error Code FA1 -Low Range Clutch Solenoid Open Circuit Or Short To Ground Error Code FA2 -Medium Range Clutch Solenoid Open Circuit Or Short To Ground Error Code FA3 -High Range Clutch Solenoid Open Circuit Or Short To Ground Error Code FA4 -Reverse Clutch Solenoid Open Circuit Or Short To Ground

Error Code FA5 - Creeper Solenoid Open Circuit Or Short To Ground Error Code FAA - Clutch A Solenoid Open Circuit Or Short To Ground Error Code FAB- Clutch B Solenoid Open Circuit Or Short To Ground Error Code FAC - Clutch C Solenoid Open Circuit Or Short To Ground Error Code FAD - Clutch D Solenoid Open Circuit Or Short To Ground Error Code FAE - Clutch E Solenoid Open Circuit Or Short To Ground Error Code FB1 - Low Range Clutch Solenoid Over Voltage Error Code FB2 - Medium Range Clutch Solenoid Over Voltage Error Code FB3 - High Range Clutch Solenoid Over Voltage Error Code FB4 - Reverse Clutch Solenoid Over Voltage Error Code FB5 - Creeper Solenoid Over Voltage Error Code FBA - Clutch A Solenoid Over Voltage Error Code FBB - Clutch B Solenoid Over Voltage Error Code FBC - Clutch C Solenoid Over Voltage Error Code FBD - Clutch D Solenoid Over Voltage Error Code FBE - Clutch E Solenoid Over Voltage Error Code FC0 - Secondary Controller (CFPS) Is Not Configured Error Code FC1 - Medium Range Clutch Not Calibrated Error Code FC2 - High Range Clutch Not Calibrated Error Code FC3 - Reverse Clutch Not Calibrated Error Code FC5 - Creeper Travel Out Of Range Error Code FC8 - Creeper Not Calibrated Error Code FC9 - 19th Gear Clutch Not Calibrated or Configuration error (download the latest software) Error Code FCA - Clutch A Not Calibrated Error Code FCB - Clutch B Not Calibrated Error Code FCC - Clutch C Not Calibrated Error Code FCD - Clutch D Not Calibrated Error Code FCE - Clutch E Not Calibrated Error Code FCF - Low Range Clutch Not Calibrated Error Code N - Shift To Neutral To Re-Enable The Transmission PTO, MFD, and Differential Lock Codes (XCM for PTO and EMU for MFD and Differential Lock) Error Code P01 - Rear PTO Brake Solenoid Stuck Off Error Code P02 - Rear PTO Brake Solenoid Stuck On Error Code P03 - Rear PTO Brake Output Open Circuit Error Code P05 Rear PTO Brake Switch open circuit Error Code P06 - Rear PTO Not Calibrated Error Code P07 - Rear PTO Circuit Over Current Error Code P08 - Rear PTO Solenoid Open Circuit Or Short To Ground Error Code P15 - Differential Lock Solenoid Stuck Off Error Code P16 - Differential Lock Solenoid Stuck On Error Code P17 - Differential Lock Output Open Circuit Error Code P18 - Differential Lock Driver Over Temperature Error Code P21 - 4wd Solenoid Stuck Off

Error Code P22 - 4wd Solenoid Stuck On Error Code P23 - 4wd Output Open Circuit Error Code P24 - 4wd Driver Over Temperature Error Code P27 - PTO Speed Sensor Open Circuit Error Code P31 - Steering Sensor Out Of Range - (Maximum Voltage) Error Code P32 - Steering Sensor Out Of Range - (Minimum Voltage) Error Code P33 - Rear PTO Cab Switch Short Circuit Error Code P34 - Fender Mounted Rear PTO Switch Short Circuit Error Code P35 - Fender Mounted Rear PTO Switch Open Circuit Error Code P36 - Rear PTO Failure To Start Error Code P37 - Rear PTO Cab Switch Open Circuit Error Code P38 PTO Switch time out error Error Code P50 Incorrect code displayed because of XCM software (download the latest software) Error Code P57 Incorrect code displayed because of XCM software (download the latest software) Error Code P66 Incorrect code displayed because of XCM software (download the latest software) Error Code P80 Incorrect code displayed because of XCM software (download the latest software) Electronic Hydraulic Remote Codes (XCM) Error Code R1 - EHR Control Unit 1 Lever Not Calibrated Error Code R2 - EHR Control Unit 2 Lever Not Calibrated Error Code R3 - EHR Control Unit 3 Lever Not Calibrated Error Code R4 - EHR Control Unit 4 Lever Not Calibrated Error Code R11 - EHR Control Unit 1 Float Switch Error Error Code R12 - EHR Control Unit 1 Active Switch Error Error Code R13 -CAN Messages Received By The EHR Valve 1 Are Corrupted Or Missing Error Code R14 -Valve 1 Supply Under Voltage/Over Voltage Or Output Stage Faulty Or Transducer Faulty Or Spool Neutral Error Or Spool Not Neutral Error Error Code R15 -Valve 1 Spool Travel Short Or Spool Travel Excessive Or Open Centre Not Reached Error Code R16 - EHR Control Unit 1 Full Flow Switch Error Error Code R17 -No Communication Between The EHR Valve 1 And The Central Controller (XCM) Error Code R18 - EHR Control Unit 1 Lever Faulty Error Code R21 - EHR Control Unit 2 Float Switch Error Error Code R22 - EHR Control Unit 2 Active Switch Error Error Code R23 -CAN Messages Received By The EHR Valve 2 Are Corrupted Or Missing Error Code R24 -Valve 2 Supply Under Voltage/Over Voltage Or Output Stage Faulty Or Transducer Faulty Or Spool Neutral Error Or Spool Not Neutral Error Error Code R25 -Valve 2 Spool Travel Short Or Spool Travel Excessive Or Open Centre Not Reached

Error Code R26 - EHR Control Unit 2 Full Flow Switch Error Error Code R27 -No Communication Between The EHR Valve 2 And The Central Controller (XCM) Error Code R28 - EHR Control Unit 2 Lever Faulty Error Code R31 - EHR Control Unit 3 Float Switch Error Error Code R32 - EHR Control Unit 3 Active Switch Error Error Code R33 -CAN Messages Received By The EHR Valve 3 Are Corrupted Or Missing Error Code R34 -Valve 3 Supply Under Voltage/Over Voltage Or Output Stage Faulty Or Transducer Faulty Or Spool Neutral Error Or Spool Not Neutral Error Error Code R35 -Valve 3 Spool Travel Short Or Spool Travel Excessive Or Open Centre Not Reached Error Code R36 - EHR Control Unit 3 Full Flow Switch Error Error Code R37 -No Communication Between The EHR Valve 3 And The Central Controller (XCM) Error Code R38 - EHR Control Unit 3 Lever Faulty Error Code R41 - EHR Control Unit 4 Float Switch Error Error Code R42 - EHR Control Unit 4 Active Switch Error Error Code R43 -CAN Messages Received By The EHR Valve 4 Are Corrupted Or Missing Error Code R44 -Valve 4 Supply Under Voltage/Over Voltage Or Output Stage Faulty Or Transducer Faulty Or Spool Neutral Error Or Spool Not Neutral Error Error Code R45 -Valve 4 Spool Travel Short Or Spool Travel Excessive Or Open Centre Not Reached Error Code R46 - EHR Control Unit 4 Full Flow Switch Error Error Code R47 -No Communication Between The EHR Valve 4 And The Central Controller (XCM) Error Code R48 - EHR Control Unit 4 Lever Faulty Error Code R53 -CAN Messages Received By The EHR Valve 5 Are Corrupted Or Missing Error Code R54 -Valve 5 Supply Under Voltage/Over Voltage Or Output Stage Faulty Or Transducer Faulty Or Spool Neutral Error Or Spool Not Neutral Error Error Code R55 -Valve 5 Spool Travel Short Or Spool Travel Excessive Or Open Centre Not Reached Error Code R57 -No Communication Between The EHR Valve 5 And The Central Controller (XCM) Active Flash Codes (AUX) See 55-9-543 *55-10-553* of the Repair Manual Error Code 11 - No control message, CAN BUS message fault Error Code 13 - Implausible control message, CAN BUS message fault Error Code 16 - EEPROM inconsistent, Software fault Error Code 17 - Messages not received in the specified time, CAN BUS message fault Error Code 21 - Under voltage, Supply voltage low Error Code 22 - Over voltage, Supply voltage high Error Code 23 - Spool deflection too short, Valve internal fault, possibly mechanical Error Code 24 - Spool deflection excessive, Valve internal fault, possibly mechanical

Error Code 25 - Open centre position not reached, Valve internal fault, possibly mechanical Error Code 26 - Manual operation detected, Valve has been operated manually Error Code 31 - Under 8 volts, Displated only if the valve does not shut-down automatically. Valve will shut off the output stage. Error Code 32 - Over 36 or 45 volts, Displayed only if the valve does not shut-down automatically. Valve wil shut off the output stage. Error Code 41 - Over 45 Volts, Valve will internally shut-down. Error Code 42 - Output stage for the pilot solenoid valve fault, Valve internal fault. Error Code 43 - Position transducer fault, Position of the spool detected by the transducer. Error Code 81 - Valve spool cannot be returned to neutral, Valve internal fault, possibly mechanical. Error Code 82 - Valve spool not in neutral when switched on, Valve internal fault, possibly mechanical. Error Code 83 - Checksum error, Self diagnostic check of the system.

Electronic Engine Codes (ECU) or PTO/Hand Throttle Codes (XCM) (both displayed on the EIC as a lower case t) Error Code T1 -Foot Throttle Position Sensor, Grounded Or Current Above Normal Range Error Code T2 -Foot Throttle Position Sensor, Open Circuit Or Current Below Normal Range Error Code T3 -Foot Throttle Position Sensor, Shorted To Low Source Error Code T4 -Foot Throttle Position Sensor, Shorted To High Source Error Code T5 -CAN AE Message (Torque Set point), Data Valid But Below Normal Range Error Code T6 -CAN AE Message (Torque Set point), Data Incorrect Error Code T7 -CAN AE Message (Torque Set point), Data Valid But Above Normal Range Error Code T8 -Ambient Pressure Sensor, Grounded Or Current Above Normal Range Error Code T9 -Ambient Pressure Sensor, Open Circuit Or Current Below Normal Range Error Code T13 - Test Shut Off Paths, Data Valid But Above Normal Range Error Code T14 - Test Shut Off Paths, Shorted To High Source Error Code T15 - Shut-Off Signal, Data Valid But Above Normal Range Error Code T16 - Shut-Off Signal, Shorted To High Source Error Code T17 - PCU Power Supply, Data Valid But Above Normal Range Error Code T18 - PCU Power Supply, Shorted To High Source Error Code T19 -Fuel Quantity Shut-Off, Data Valid But Above Normal Range Error Code T1A -Fuel Quantity Shut-Off, Shorted To High Source Error Code T1B - Voltage Monitoring, Data Valid But Below Normal Range Error Code T1C - Voltage Monitoring, Data Incorrect Error Code T1D - Voltage Monitoring, Data Valid But Above Normal Range Error Code T1E - Monitoring Module, Data Valid But Above Normal Range Error Code T1F - Monitoring Module, Shorted To High Source

Error Code T20 -After-Run Not Completed, Data Valid But Below Normal Range Error Code T21 -After-Run Not Completed, Data Valid But Above Normal Range Error Code T22 -Boost Air Temperature Sensor, Grounded Or Current Above Normal Range Error Code T23 -Boost Air Temperature Sensor, Open Circuit Or Current Below Normal Range Error Code T24 -Boost Air Temperature Sensor, Shorted To Low Source Error Code T25 -Boost Air Temperature Sensor, Data Valid But Above Normal Range Error Code T26 -Boost Air Temperature Sensor (PHY), Grounded Or Current Above Normal Range Error Code T27 -Boost Air Temperature Sensor (PHY), Data Incorrect Error Code T28 -Boost Air Temperature Sensor (PHY), Data Valid But Above Normal Range Error Code T29 -Boost Air Temperature Sensor (PHY), Shorted To High Source Error Code T2C - Battery Voltage, Data Valid But Above Normal Range Error Code T2D - Battery Voltage, Open Circuit Or Current Below Normal Error Code T2E- Battery Voltage, Shorted To Low Source Error Code T31 -Boost Air Pressure Sensor, Grounded Or Current Above Normal Range Error Code T32 -Boost Air Pressure Sensor, Open Circuit Or Current Below Normal Range Error Code T33 -Boost Air Pressure Sensor, Shorted To Low Source Error Code T34 -Boost Air Pressure Sensor, Shorted To High Source Error Code T35 -Boost Air Pressure Sensor (PHY), Data Valid But Above Normal Range Error Code T36 -Boost Air Pressure Sensor (PHY), Data Incorrect Error Code T37 -Boost Air Pressure Sensor (PHY), Shorted To High Source Error Code T38 -Vehicle CAN Bus Transmit, Data Valid But Above Normal Range Error Code T39 -Vehicle CAN Bus Transmit, Shorted To High Source Error Code T3A - PCU Initialization, Data Valid But Above Normal Range Error Code T3B - PCU Initialization, Shorted To High Source Error Code T3C - Solenoid Valve, Data Valid But Below Normal Range Error Code T3D - Solenoid Valve, Data Incorrect Error Code T3E - Solenoid Valve, Data Valid But Above Normal Range Error Code T3F - PSG Message, Data Valid But Above Normal Range Error Code T40 - PSG Message, Shorted To High Source Error Code T41 - Msg1 Message, Data Valid But Above Normal Range Error Code T42 - Msg1 Message, Shorted To High Source Error Code T45 - CAN CCVSS Message, Data Valid But Below Normal Range Error Code T46 - CAN CCVSS Message, Data Incorrect Error Code T47 - CAN CCVSS Message, Data Valid But Above Normal Range Error Code T4A -Coolant Temperature Sensor, Grounded Or Current Above Normal Range Error Code T4B -Coolant Temperature Sensor, Open Circuit Or Current Below Normal Range Error Code T4C -Coolant Temperature Sensor, Shorted To Low Source Error Code T4D -Coolant Temperature Sensor, Data Valid But Above Normal Range

Error Code T4E-Coolant Temperature Sensor (PHY), Data Valid But Above Normal Range Error Code T4F -Coolant Temperature Sensor (PHY), Data Incorrect Error Code T50 -Coolant Temperature Sensor (PHY), Shorted To High Source Error Code T57 -Crankshaft Speed Sensor, Data Valid But Below Normal Range Error Code T58 -Crankshaft Speed Sensor, Data Incorrect Error Code T59 -Crankshaft Speed Sensor, Shorted To Low Source Error Code T5A -Crankshaft Speed Sensor, Shorted To High Source Error Code T5B -Reverse Polarity Of Engine Speed Sensor, Data Valid But Below Normal Range Error Code T5C -Reverse Polarity Of Engine Speed Sensor, Data Valid But Above Normal Range Error Code T66 - IAT System, Data Valid But Below Normal Range Error Code T67 - IAT System, Data Valid But Above Normal Range Error Code T68 - Main Relay Defect, Data Valid But Above Normal Range Error Code T69 - Main Relay Defect, Shorted To High Source Error Code T72 - Engine Overspeed, Data Valid But Below Normal Range Error Code T73 - Engine Overspeed, Data Valid But Above Normal Range Error Code T74 - ADC In PCU, Data Valid But Below Normal Range Error Code T75 - ADC In PCU, Data Valid But Above Normal Range Error Code T76 - Control Duration, Data Valid But Above Normal Range Error Code T77 - Control Duration, Shorted To High Source Error Code T7A -EEPROM Checksum In PCU, Data Valid But Below Normal Range Error Code T7B -EEPROM Checksum In PCU, Data Valid But Above Normal Range Error Code T7C - EEPROM In PCU, Data Valid But Below Normal Range Error Code T7D - EEPROM In PCU, Data Valid But Above Normal Range Error Code T7E -Crankshaft Signal In PCU, Data Valid But Below Normal Range Error Code T7F -Crankshaft Signal In PCU, Data Valid But Above Normal Range Error Code T80 - Pump Map, Data Valid But Below Normal Range Error Code T81 - Pump Map, Data Valid But Above Normal Range Error Code T84 - Ram In PCU, Data Valid But Below Normal Range Error Code T85 - Ram In PCU, Data Valid But Above Normal Range Error Code T86 -Solenoid Valve Power Stage, Data Valid But Below Normal Range Error Code T87 -Solenoid Valve Power Stage, Data Valid But Above Normal Range Error Code T88 -Solenoid Valve Power Stage 2, Data Valid But Below Normal Range Error Code T89 -Solenoid Valve Power Stage 2, Data Valid But Above Normal Range Error Code T8A - Shut-Off Signal, Data Valid But Below Normal Range Error Code T8B - Shut-Off Signal, Data Valid But Above Normal Range Error Code T8C - Pump Timing Device, Data Valid But Below Normal Range Error Code T8D - Pump Timing Device, Data Valid But Above Normal Range Error Code T8E -Fuel Injection Pump Temperature, Data Valid But Below Normal Range Error Code T8F -Fuel Injection Pump Temperature, Data Incorrect Error Code T90 -Fuel Injection Pump Temperature, Data Valid But Above Normal Range Error Code T93 - Reserve 1, Data Valid But Above Normal Range

Error Code T96 - Monitoring Module, Data Valid But Below Normal Range Error Code T97 - Monitoring Module, Data Valid But Above Normal Range Error Code TA -Ambient Pressure Sensor, Shorted To Low Source Error Code TB -Ambient Pressure Sensor, Data Valid But Above Normal Range Error Code TC -Ambient Pressure Sensor (PHY), Data Valid But Below Normal Range Error Code TD -Ambient Pressure Sensor (PHY), Data Incorrect Error Code TE -Ambient Pressure Sensor (PHY), Data Valid But Above Normal Range Error Code TF -Ambient Pressure Sensor (PHY), Shorted To High Source Error Code TAA - PCU CAN Chip, Data Valid But Above Normal Range Error Code TAB - PCU CAN Chip, Shorted To High Source Error Code TAC - PCU CAN Bus Off, Data Valid But Above Normal Range Error Code TAD - PCU CAN Bus Off, Shorted To High Source Error Code TAE - Vehicle CAN Chip, Data Valid But Above Normal Range Error Code TAF - Vehicle CAN Chip, Data Incorrect Error Code TB0 - Vehicle CAN Chip, Shorted To Low Source Error Code TB1 - Vehicle CAN Chip, Shorted To High Source Error Code TB2 - Vehicle CAN Bus Off, Data Valid But Above Normal Range Error Code TB3 - Vehicle CAN Bus Off, Shorted To High Source Error Code TB4 -CAN VE Message (Speed Set point), Data Valid But Below Normal Range Error Code TB5 -CAN VE Message (Speed Set point), Data Incorrect Error Code TB6 -CAN VE Message (Speed Set point), Data Valid But Above Normal Range Error Code TC2 - PTO Twist Sensor Open Circuit Error Code TC3 - PTO Twist Sensor Short To Ground Error Code TC4 - Engine Torque/RPM Sensor Open Circuit Error Code TC5 - Engine Torque/RPM Sensor Short To Ground Error Code TC6 - PTO Twist Sensor Not Calibrated Error Code TC7 - No Signal From The PTO Twist Speed Sensor Error Code TC8 - No Signal From The Engine Torque/RPM Sensor Error Code TC9 - PTO Twist Speed Sensor Over Voltage Error Code TCA - CAN In PCU, Shorted To Low Source Error Code TCB - CAN In PCU, Shorted To High Source Error Code TCC - PCU Initialization, Data Valid But Below Normal Range Error Code TCD - 1 CAN Chip, Data Valid But Below Normal Range Error Code TCE - 1 CAN Chip, Data Valid But Above Normal Range Error Code TCF - 1 CAN Chip, Shorted To High Source Error Code TD0 - PCU Power Supply, Data Valid But Below Normal Range Error Code TD1 -Hand Throttle Position Sensor Potentiometer 1 Over Voltage Error Code TD2 -Hand Throttle Position Sensor Potentiometer 1 Under Voltage Error Code TD3 -Hand Throttle Position Sensor Potentiometer 2 Over Voltage Error Code TD4 -Hand Throttle Position Sensor Potentiometer 2 Under Voltage Error Code TD5 - Hand Throttle Position Sensor Difference Error Error Code TD6 - Hand Throttle Idle Switch Open Circuit Error Code TD7 - Hand Throttle Idle Switch Closed Circuit Error Code TD8 - PCU Power Supply, Data Valid But Above Normal Range

Error Code TE1 - Transmission oil plausibility error (transmission oil temperature signal out of limits) Error Code TE2 - Fan rpm out of range Error Code TE3 - Maximum fan speed low error Error Code TE4 - Fan speed signal error Error Code TE5 - Last element (unknown input)