L6B TFT- LCD TV SERVICE MANUAL

CONTENTS

PAGES

Safety instructions Technical specifications Panel Specification Back appearance of TV Interconnecton Diagram Block diagram Block diagram of power supply Service mode Service Mode items and values Data sheet of important ICs and parts Recommended Part List Frequency list of channels

1 2 3 5 5 6 7 8 10 11 23 25

SAFETY PRECAUTIONS
GENERAL GUIDELINES 1. It is advised to insert an isolation transformer in the
AC supply before servicing a hot chassis. 2. Always use the manufacturers replacement safety components. The critical safety components marked with on the schematics diagrams should not be by other substitutes. Other substitute may create the electrical shock , fire or other hazards. Take attention to replace the spacers with the originals. Furthermore where a short circuit has occurred , replace those components that indicate evidence of overheating. 3. After servicing , see that all the protective devices such as insulation barriers, insulation papers, shields and isolation R-C combinations are correctly installed. 4. When the receiver is not being used for a long time of period of time , unplug the power cord of the Adaptor from the AC outlet.

There are electro-static sensitive components such as CMOS in LCD Module. Please earth human body when handle the LCD.In addition, please do not touch the interface connector pin with bare. 8 - Do not operate for a long time under the same pattern Operating LCD for a long time under the same pattern can cause image persistence and can damage it. Please follow following guidance. 1. Turn the power off when do not use. 2. Change the pattern periodically. LEAKAGE CURRENT COLD CHECK 1. Unplug the AC cord and connect a jumper
between the two prongs of the plug. 2. Turn the receivers power switch. 3. Measure the resistance value with an ohmmeter, between the jumpered AC plug and each exposed metallic cabinet part on the receiver. When the exposed metallic part a return path to the chassis the reading should be between 4Mohm and the 20Mohm. When the exposed metal does not have a return path to the chassis, the reading must be infinite.

Color TFT LCD Module is very sensitive both electrically and physically.Users, therefore, are requested to follow the Guidance of handling color TFT LCD Moduleon the followings.
1 -Be careful not to make scratch on the

LEAKAGE CURRENT HOT CHECK 1. Plug the AC cord directly in to the AC outlet. Do
not use an isolation transformer for this check.

polarizer. Surface of polarizer is soft and can be physically damaged easily.Please do not touch, push or rub polarizer surface with materials over HB hardness. 2 - Keep clean the surface. Please wear rubber glove when touch the surface of LCD screen. Please use soft and anti-static material as cleaner. 3 -Keep out of water.Water on/in the LCD may cause electrical short or corrosion. Please wipe out dry or water carefully. 4 -Prevent swift Temperature & Humidity change.Instantaneous temperature and/or humidity change can make dew or ice which cause nonconformance such as malfunction. 5 - High temperature & high humidity reduce the life-time. LCD is not proper to be used at high temperature and high humidity. Please keep specified temperature and humidity condition. 6 - Keep out of Corrosive Gas.Corrosive gas effect the polarizer and the circuit chemically and cause defects accordingly. 7 - Electrostatic discharge can make Damage

2. Connect a 2Kohm 10W resistor in series with an 3. 4. 5. 6.

exposed metallic part on the receiver and an earth, such as a water pipe. Use an AC voltmeter with high impedance to measure the potential across the resistor. Check each exposed metallic part and check the voltage at the each point. Reverse the AC plug at the outlet and repeat each of the above measurements. The potential at the any point should not exceed 1.4 Vrms. In case a measurement is outside the limits specified , there is the possibility of a shock hazard , and the receiver should be repaired and rechecked before it is returned to the customer.

HOT CHECK CIRCUIT AC-Voltmeter

TO INSTRUMENTS EXPOSED METALLIC PARTS

Water pipe (earth)

2 K Ohm

L6B TECHNICAL SPECIFICATION

Receiving System Comb Filter LTI, CTI Filters DVI 1.0 Compliant DVI Receiver Gamma Correction PIP\PAP\POP\PAT OSD Level (1.5, 2.5, Teleweb) Teletext WSS VPS\PDC 4:3 16:9 Picture Formats (4:3, 16:9, 14:9, Panorama, LetterBox, Subtitle) 14:9 Panorama Letterbox Subtitle Zoom WSS (Wide Screen Signalling) ATS (Automatic Tuning System) Manual Search Number of Program Storage No Ident Timer Picture Freeze Equalizer AVL (Automatic Volume Level) Sound Status Memory Picture Status Memory Swap Child Lock Program Lock Picture Format Switching Tru Pin 8 Auto RGB Detect Tru Pin 16 Timer Picture Smart (User, Soft, Natural, Rich) Sound Smart (User, Music, Sports, Cinema, Speech) Scart2 Out Selectable S-Video Input Through Scart2 Audio Output Power RMS in Max at 10% THD) Stereo (German A2, Nicam, BTSC) S-video In (DIN) AV In (3 RCA) AV Out (3 RCA) PC Audio (L, R) D-Sub 15 Headphone CVBS In Y\C In DVI In CVBS Out 1 1 1 1 1 1 4 1 YES 4 Off Timer (Sleep Timer) On Timer Type (Fast\Top\Simple) Page Memory Resolution 2 Pixel \ Clk Support PAL B/G+I+D/K SECAM L/L' Adaptive 4H\2H + + VGA to SXGA + 8 to 10-bit LUT + Graphics Based 8-bit\pixel Teletext 1.5 Simple, Fast, Top 800p + + + + + + + + + + Frequency Search Channel Table Search + + + + + + + + + + + + + + + + + + 2x5W for 22"W, 23"W 2x10W for 26"W 2x10W for 30"W German A2, Nicam

PANEL SPECIFICATION
Sizes Manufacturer Interface Resolution Brightness (cd/m2)>= Contrast>= Response Time (Tr+Tf) msec =< Viewing Angle R\L\H\L>= Adaptor nput PoweR consumptions St-By Power Consumption Input Range 22" Samsung Single LVDS WXGA (1280x720) 450 500 25 85/85 85/85 15V 100W <4W 23" 26" 27" LGChimei AUO Singel LVDS WXGA (1280x720) 550 600 25 85/85/85/85 Built-in TV 120W <4W 30" Chimei LG-Philips Single LVDS WXGA (1280x768) 550 600 25 85/85/85/85 Built-in TV 140W <4W AUO 32"

Samsung LG- Samsung Philips Hannstar Philips Single LVDS WXGA (1280x768) 450 400 25 85/85 85/85 24V 100W <4W Singlel LVDS

Single LVDS WXGA (1280x768) 450 700 23 85/85/85/85 Built-in TV 180W <4W

WXGA (1280x768) 450 400 25 85/85/85/85 Built-in TV 120W <4W

100V-240V/50- 60Hz 100V-240V/50- 60Hz 100V-240V/50- 60Hz 100V-240V/50- 60Hz 100V-240V/50- 60Hz 100V-240V/50- 60Hz

BACK SIDE APPEARANCES

CONTROL BOARD

SPEAKERS

POWER SWITCH

220VAC INPUT
LED/IR BOARD

MAIN CHASSIS

POWER SUPPLY BOARD

NOTE: LOCATION AND THE SHAPE OF IR /LED BAORD, CONTROL BOARD AND MAIN SWITCH BOARD MAY CHANGE ACCORDING TO THE COSMETIC OF THE TV AND SIZE

TO PANEL

MAIN CHASSIS

JP452

JP451

JP453

CN1

POWER SUPPLY MODULE

S150

SPEAKER S2 TO PANEL S350 S550 CN3 CN2

S50

JP450

TO HEADPHONE JACK

MAIN POWER SWITCH MODULE KEY BOARD MODULE

IR RECEIVER/LED MODULE

220V AC INPUT

L6B BLOCK DIAGRAM

Tuner-Main IF IC TDA9886T
Multi Standard Video Decoder SAA7118MP

RF In

Video-Main
QSS-Main

SDRAM MT48LC16M 16 Bit YUV PW1231 De-Interlacer 24 Bit RGB Flash Memory AM29VL160

Tuner-PIP

IF IC TDA9886T
PIP-Video Main-Video QSS-PIP

EEPROM 24C64

AV-Out Video AV4 Video-In Video In/Out

SCART 1 2 3 Audio-In/Out

Scart RGB

Pin 8 Switch PCF8591

I2C Communication
SC1-SC2 RGB

De-Interlacer Scaler OSD Micro-Cont. Gamma Corr. IR In

Progressive or Intrelaced 24 Bit Dual RGB ,HS,VS DE,PCLK

LVDS Transmitter DS090C385

Multi Standard Video Decoder SAA7118MP

Video Switch TDA6415C

Video-PIP 16 Bit YUV

PW181 IMAGE PROCESSOR

TO THE PANEL

RGB Switch PI5V30

AV4 Audio-In Audio-Switch TDA6420 AV Out Audio

SVHS Y/C

Audio In-Out

AUDIO PROCESSOR MSP3410D

Stand by LEDs Reset Mute B/L Enable Digital Dim 48 Bit RGB VS/HS Dual nterface for FPD AD9887
RGB HS/VS-In DVI Input DVI Socket

Audio Amplifier TA2024

Headphone Amp. TDA1308

EEPROM 24LC21

EEPROM 24LC21

PC DVI Audio -In

Headphone Jack

SVHS Socket
Speaker

D-SUB 15 socket

L6B POWER SUPPLY BLOCK DIAGRAM (MAIN CHASSIS)

J450 U451 FDS9933A DC_IN GND F451 S450 VOLTAGE DOUBLER '33V U452 FDS9933N 12V_AMP +5V U457 NCP1117 U456 LM317 +8V +3,3V_STBY 12V (5V) F450 U454 LM2576 +5V_STBY U458 NCP1117 +2,5V_STBY

12V

U450 NCP117

+1,5V_STBY

GND

STAND_BY

+3,3V

U453 FDS9933N

+12V

U455 LM2576

PANEL_POWER

PNL_EN

+12V_INVERTER

L6B SERVICE MENU

1. Activating the Service Menu When the menu is on the screen press 9, 3, 0, 1 on the remote controller. This will activate the service menu. 2. Service Menu Structure The service menu has three items: display, calibre and version 2.1 Display Display item has seven options: a- Panel Panel option gives information about the current panel resolution. It is a read only option and can not be set. b- Power on time Power on time gives information about the last update time of the SW running. It is a read only option and can not be set. c- Backlight on time Backlight on time option reserved. d- Scart prescale Scart prescale option sets the prescale values for the input sounds entering the scart input of the MSP(Micronas Sound Processor). Changing this value you can adjust the level of the output sound going to loudspeakers for all the sources except the Tuners. The range is between 0 and 100. e- nicam prescale Nicam prescale option sets the prescale values for the Nicam standard sounds for tuner inputs. Changing this value you can adjust the level of the output sound going to loudspeakers for Nicam sounds entering the analog sound input of MSP. The range is between 0 and 100. f- fm/am prescale fm/am prescale option sets the prescale values for the FM/AM standard sounds for tuner inputs. Changing this value you can adjust the level of the output sound going to loudspeakers for FM/AM sounds entering the analog sound input of MSP. The range is between 0 and 100. g- Agc(Automatic Gain Control) adjust Agc adjust option sets the input voltage going to IF decoder AGC pin. Changing this value you can adjust this voltage for optimum Tuner performance. The range is between 0 and 31. h- R/G/B Brightness/Contrast: These are used for color bias adjustment. The range is Between 0 and 255

2.2 Calibre Calibre item has nine options: a- video format Video format option force the video format to the desired format. Selectable formats are Auto, Pal, NTSC and SECAM. b- colorspace Colorspace option gives the information about the video input colorspace input to PW181 IC. Do not change this value unless an error occurred in the colors displayed. c- test pattern This option activates the internal pattern of PW181 IC. There are 3 choices: none, vert bars, solid color. None will deactivate the internal pattern. Vert bars choice activates the bar pattern for the selected color component. Solid color activates the solid pattern with one color selected in color component and also you can change the level of the color by solid field level. d- Color components: This option selects the color for the internal pattern of PW181 IC. There are 4 choices: all, red, green and blue. If you choose all, you can see the white pattern and if you choose one of the other choices you can see the test pattern with the selected color. e- solid field level This option will adjust the level of the colors for the test pattern. The range is betwwen 1 and 64. f- Initial ATS This option will enable or disable the Initial setup for the TV. Setting this option to On, the TV will open from the Quick setup menu. Setting this option to Off will disable this option. g- factory reset Factory reset option executes a reset operation for the NVRAM. Pressing OK when this option is selected will erase the NVRAM and load default values to NVRAM. h- dpms This option selects the Power option for the TV. Setting this option to On the TV will switch to the last state for power on transition. Setting this to Off will disable this option and the TV will always switch to Stand-by state while power on transition. i- osd timeout This option sets the OSD timeout for the main menu structure. Selections are 5, 15 and 60 secs. The default is 60 sec. 2.3 Version This item gives the information about the version of the software. Also you can see the last modified time for the GUI(graphical user interface).

L6 CHASSIS SERVICE MODE ITEMS

display menu
ITEM panel power on time back light time scart prescale nicam prescale fm/am prescale agc adjust red brightness red contrast green brightness green contrast blue brightness blue contrast TYPICAL VALUES/OPTIONS 1280x768 03:39:45 03:39:45 25 45 24 16 128 128 128 128 128 128

calibre menu
ITEM video format color space test pattern color components solid field level initial ats factory reset dpms osd time out TYPICAL VALUES/OPTIONS auto RGB none all 33 on press <ok> to reset on 60 sec

version
ITEM Software GUI Project; L6B Toshiba Generated Date: October 01,2004 at 22.42 TYPICAL VALUES/OPTIONS SL630T_CH1_T13 L6B 1.22 Chi30

TEA6415C
BUS-CONTROLLED VIDEO MATRIX SWITCH
I I

I I I

I I

I I

20MHz BANDWIDTH CASCADABLE WITH ANOTHER TEA6415C (INTERNAL ADDRESS CAN BE CHANGED BY PIN 7 VOLTAGE) 8 INPUTS (CVBS, RGB, MAC, CHROMA, ...) 6 OUTPUTS POSSIBILITY OF MAC OR CHROMA SIGNAL FOR EACH INPUT BY SWITCHING-OFF THE CLAMP WITH AN EXTERNAL RESISTOR BRIDGE BUS CONTROLLED 6.5dB GAIN BETWEEN ANY INPUT AND OUTPUT -55dB CROSSTALK AT 5MHz FULLY ESD PROTECTED

DIP20 (Plastic Package) ORDER CODE : TEA6415C

DESCRIPTION The main function of the TEA6415C is to switch 8 video input sources on the 6 outputs. Each output can be switched to only one of the inputs whereas but any same input may be connected to several outputs. All the switching possibilities are controlled through the I2C bus. PIN CONNECTIONS
INPUT DATA INPUT CLOCK INPUT INPUT PROG INPUT VCC INPUT 1 2 3 4 5 6 7 8 9 10 20 19 18 17 16 15 14 13 12 11 INPUT GROUND OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT
6415C-01.EPS

SO20 (Plastic Micropackage) ORDER CODE : TEA6415CD

GROUND INPUT

TEA6415C
BLOCK DIAGRAM
P ERI TV1 P ERI TV2

TTX

LUMA PIP CHROMA POWER

MAC DEC.

GND

18
CVBS (MAC/DEC)

17

16

15

14

13

12

CVBS (P ERI P LUG1)

CVBS (AM TUNER) MAC S IGNAL (AMTUNER)

CVBS (P ERI P LUG2)

CVBS (FM TUNER) MAC S IGNAL (FM TUNER)

10

11

SYNCHRO (TTX/BTX)

20

BUS DECODER

T E A 6 4 1 5 C
9 VCC 19 GND
6415C-02.EPS

2 DATA

7 P ROG

4 CLOCK

GENERAL DESCRIPTION The main functionof the IC is to switch 8 video input sources on 6 outputs. Each output can be switched on only one of each input. On each input an alignment of the lowest level of the signal is made (bottom of synch. top for CVBS or black level for RGB signals). Each nominal gain between any input and output is 6.5dB. For D2MAC or Chroma signal the alignment is switched off by forcing, with an external resistor bridge, 5 VDC on the input. Each input can be used as a normal input or as a MAC or Chroma

input (with external resistor bridge). All the switching possibilities are changed through the BUS. Driving 75 load needs an external transistor. It is possible to have the same input connected to several outputs. The starting configuration upon power on (power supply : 0 to 10V) is undetermined. In this case, 6 words of 16 bits are necessary to determine one configuration. In other case, 1 word of 16 bits is necessary to determine one configuration.

I2C-bus controlled single and multistandard alignment-free IF-PLL demodulators

1 FEATURES

TDA9885; TDA9886

5 V supply voltage Gain controlled wide-band Vision Intermediate Frequency (VIF) amplifier, AC-coupled Multistandard true synchronous demodulation with active carrier regeneration: very linear demodulation, good intermodulation figures, reduced harmonics, and excellent pulse response Gated phase detector for L and L-accent standard Fully integrated VIF Voltage Controlled Oscillator (VCO), alignment-free, frequencies switchable for all negative and positive modulated standards via I2C-bus Digital acquisition help, VIF frequencies of 33.4, 33.9, 38.0, 38.9, 45.75, and 58.75 MHz 4 MHz reference frequency input: signal from Phase-Locked Loop (PLL) tuning system or operating as crystal oscillator VIF Automatic Gain Control (AGC) detector for gain control, operating as peak sync detector for negative modulated signals and as a peak white detector for positive modulated signals External AGC setting via pin OP1 Precise fully digital Automatic Frequency Control (AFC) detector with 4-bit digital-to-analog converter, AFC bits readable via I2C-bus TakeOver Point (TOP) adjustable via I2C-bus or alternatively with potentiometer Fully integrated sound carrier trap for 4.5, 5.5, 6.0, and 6.5 MHz, controlled by FM-PLL oscillator Sound IF (SIF) input for single reference Quasi Split Sound (QSS) mode, PLL controlled 4 ORDERING INFORMATION PACKAGE TYPE NUMBER NAME TDA9885T/V3 TDA9885TS/V3 TDA9885HN/V3 TDA9886T/V3 TDA9886TS/V3 SO24 SSOP24 HVQFN32 SO24 SSOP24 DESCRIPTION plastic small outline package; 24 leads; body width 7.5 mm plastic shrink small outline package; 24 leads; body width 5.3 mm plastic, heatsink very thin quad at package; no leads; 32 terminals; body 5 5 0.85 mm plastic small outline package; 24 leads; body width 7.5 mm plastic shrink small outline package; 24 leads; body width 5.3 mm VERSION SOT137-1 SOT340-1 SOT617-1 SOT137-1 SOT340-1 SIF-AGC for gain controlled SIF amplifier, single reference QSS mixer able to operate in high performance single reference QSS mode and in intercarrier mode, switchable via I2C-bus AM demodulator without extra reference circuit Alignment-free selective FM-PLL demodulator with high linearity and low noise I2C-bus control for all functions I2C-bus transceiver with pin programmable Module Address (MAD) Four I2C-bus addresses via MAD. 2 GENERAL DESCRIPTION

The TDA9885 is an alignment-free multistandard (PAL and NTSC) vision and sound IF signal PLL demodulator for negative modulation only and FM processing. The TDA9886 is an alignment-free multistandard (PAL, SECAM and NTSC) vision and sound IF signal PLL demodulator for positive and negative modulation, including sound AM and FM processing. 3 APPLICATIONS

TV, VTR, PC and STB applications.

This text is here in white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here in _white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here inThis text is here in white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader. white to force landscape pages to be ... 6
handbook, full pagewidth

I2C-bus controlled single and multistandard alignment-free IF-PLL demodulators

BLOCK DIAGRAM

CVAGC(pos) VAGC (1) 16 CBL

VIF-PLL filter

external reference signal or 4 MHz crystal

TOP 9 (8)

TAGC 14 (15) CAGC(neg)

VPLL 19 (21)

REF 15 (16)

AFC 21 (23)

TUNER AGC

VIF-AGC

RC VCO

DIGITAL VCO CONTROL

AFC DETECTOR

VIF2 VIF1

2 (31) 1 (30)

VIF-PLL

SOUND TRAPS 4.5 to 6.5 MHz

(18) 17

CVBS video output: 2 V (p-p) [1.1 V (p-p) without trap]

TDA9885 TDA9886
(7) 8
SIF2 SIF1 24 (27) 23 (26)

AUD
DEEM

SINGLE REFERENCE QSS MIXER INTERCARRIER MIXER AND AM DEMODULATOR

MAD

AUDIO PROCESSING AND SWITCHES

audio output

(3) 5

de-emphasis network

(4) 6

AFD

SUPPLY

SIF AGC
CAGC
(6, 12, 13, 14, 17, 19, 25, 28, 29, 32) 13 n.c.

OUTPUT PORTS

I 2C-BUS TRANSCEIVER

NARROW-BAND FM-PLL DEMODULATOR

CAF

TDA9885; TDA9886

20 (22) VP

18 (20)
AGND

3 (1) OP1

22 (24) 11 (10) OP2

10 (9) SDA

7 (5) DGND

12 (11) SIOMAD

4 (2)
FMPLL FM-PLL filter
MHC108

SCL

sound intercarrier output and MAD select

(1) Not connected for TDA9885. Pin numbers for TDA9885HN in parenthesis.

Fig.1 Block diagram.

TEA6420
BUS-CONTROLLED AUDIO MATRIX

. . . . . . .

5 STEREO INPUTS 4 STEREO OUPUTS GAIN CONTROL 0/2/4/6dB/MUTE FOR EACH OUTPUT CASCADABLE (2 different addresses) SERIAL BUS CONTROLLED VERY LOW NOISE VERY LOW DISTORSION

SHRINK24 (Plastic Package) ORDER CODE : TEA6420

DESCRIPTION The TEA6420 switches 5 stereo audio inputs on 4 stereo outputs. All the switching possibilities are changed through the I2C bus. PIN CONNECTIONS
SHRINK24
GND CAPACITANCE VS L1 L2 L3 L4 L5 LOUT1 ROUT1 LOUT2 ROUT2 1 2 3 4 5 6 7 8 9 10 11 12 24 23 22 21 20 19 18 17 16 15 14 13 SDA SCL ADDR R1 R2 R3 R4 R5 ROUT4 LOUT4 ROUT3 LOUT3 GND CAPACITANCE VS L1 L2 L3 NC NC L4 L5 LOUT1 ROUT1 LOUT2 ROUT2 1 2 3 4 5 6 7 8 9 10 11 12 13 14

SO28 (Plastic Micropackage) ORDER CODE : TEA6420D

SO28
28 27 26 25 24 23 22 21 20 19 18 17 16 15 SDA SCL ADDR R1 R2 R3 NC NC R4 R5
6420-01.EPS / 6420-02.EPS

ROUT4 LOUT4 ROUT3 LOUT3

TEA6420
BLOCK DIAGRAM
RIGHT INPUTS

T E A 6 4 2 0

GAIN = 0/2/4/6dB

RIGHT OUTP UTS

VS

SDA SUPPLY

BUS DECODER

S CL ADDR

GND

LEF T OUTP UTS

LEF T INPUTS

ABSOLUTE MAXIMUM RATINGS

Symbol VCC Toper Tstg Supply Voltage Operating Ambient Temperature Storage Temperature Parameter Value 10.2 0, + 70 - 20, + 150 Unit
o o

C C

THERMAL DATA
R th(j-a) Junction Ambient Thermal Resistance SHRINK24 SO28 75 75
o

C/W

ELECTRICAL CHARACTERISTICS TA = 25oC, VS = 10V, RL = 10k, RG = 600, f = 1kHz (unless otherwise specified)
Symbol SUPPLY VS IS SVR MATRIX VIN RI CS Input DC Level Input Resistance Channel Separation VIN = 2VRMS f = 1kHz Gain = 0dB Gain = 6dB 4.5 30 80 70 5 50 90 82 5.5 100 V dB dB
6420-03.TBL

Parameter

Test Conditions

Min.

Typ.

Max.

Unit

Supply Voltage Supply Current Ripple Rejection VIN = 500mVRMS, BW = 20 - 20kHz

8 70

9 5 80

10.2 8

V mA dB

6420-02.TBL

Symbol

Parameter

Value

Unit

6420-01.TBL

6420-03.EPS

GAIN = 0/2/4/6dB

PW1231
Product Specification
General
The PW1231 is a high-quality, digital video signal processor that incorporates Pixelworks patented deinterlacing, scaling, and video enhancement algorithms. The PW1231 accepts industry-standard video formats and resolutions, and converts the input into any desired output format.The video algorithms are highly efficient, providing excellent quality video. The PW1231 Video SignalProcessor combines many functions into a single device, including memory controller, auto-configuration, and others. This high level of integration enables simple, flexible, cost-effective solutions featuring fewer required components.
Crystal

Video

Video Decoder

PW1231

Digital Output

PW1231 System Block Diagram

SDRAM

Features
Built-In Memory Controller Motion-Adaptive Deinterlace Processor Intelligent Edge Deinterlacing Digital Color/Luminance Transient Improvement (DCTI/DLTI) Interlaced Video Input Options, including NTSC and PAL Independent horizontal and vertical scaling Copy Protection Two-Wire Serial Interface

Applications: For use with Digital Displays

Flat-Panel (LCD, DLP) TVs Rear Projection TVs Plasma Displays LCD Multimedia Monitors Multimedia Projectors

Device
PW1231 PW1231-L

Application
Up to XGA

Package
160-pin PQF

NOTE: L denotes lead (Pb) free

Input Unit
Memory Unit
Film-Mode Detection (3:2 & 2:2)
Previous Video

Display Unit
Display Tim ing

Primary Video Port

Digital Output Timing

ITU-R BT 601

Deinterlacer

Motion Detect and Noise Reduction

I-Channel
RGB

Secondary Video Port

Video Input
Video Enhancem ents
Color Space Converter (CSC)

Prim ary Picture

Up Scaler

ITU-R BT 656

YUV

Tw o-Wire Interface

Program m ing Unit

Blue Screen
VSync / HSync Timing

PW1231 Internal Block Diagram

Digital Output Data

Figure 1-1 Internal Block Diagram

Pinout Information

Pin Diagram

120 119 118 117 116 115 114 113 112 111 110 109 108 107 106 105 104 103 102 101 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 PVDD PVSS MPDVSS MPAVDD SCL SDA TDO TCK TDI TMS TRSTN RESETn VDD VSS TEST DCLK DVS DHS DB0 DB1 DB2 DB3 DB4 DB5 DB6 PVDD PVSS DB7 DG0 DG1 DG2 DG3 DG4 DG5 DG6 DG7 DR0 DR1 DR2 PVDD 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41

2W_A2 2W_A1 XTALO XTALI VR7 VR6 VR5 VR4 VR3 VR2 VR1 VR0 PVHS PVVS CREF PVCLK VSS VDD VG7 VG6 VG5 VG4 VG3 VG2 VG1 VG0 SVCLK SVVS SVHS PVSS PVDD VB7 VB6 VB5 VB4 VB3 VB2 VB1 VB0 NC

PW1231
(Top View)

PVDD PVSS DPAVSS DPAVDD DPDVSS DPDVDD CGMS DEN TESTCLK VSS VDD MD0 MD15 MD1 MD14 MD2 MD13 MD3 MD12 MD4 MD11 MD5 MD10 MD6 MD9 MD7 MD8 PVSS PVDD MCLK MWE MCAS MRAS MCLKFB MA12 MA11 MA13 MA9 MA10 MA8

PVSS DR3 DR4 DR5 DR6 DR7 VDD VSS PVSS NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC PVDD NC NC MA4 MA3 MA5 MA2 MA6 MA1 MA7 MA0

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40

Figure 2-1 PW1231 Pin Layout

PW181
Product Specification
General Description
The PW181 ImageProcessor is a highly integrated system-on-a-chip that interfaces computer graphics and video inputs in virtually any format to a fixed-frequency flat panel display. Computer and video images from NTSC/PAL to WUXGA at virtually any refresh rate can be resized to fit on a fixedfrequency target display device with any resolution up to WUXGA. Video data from 4:3 aspect ratio NTSC or PAL and 16:9 aspect ratio HDTV or SDTV is supported. Multiregion, nonlinear scaling allows these inputs to be resized optimally for the native resolution of the display. Advanced scaling techniques are supported, such as format conversion using multiple programmable regions. Three independent image scalers coupled with frame locking circuitry and dual programmable color lookup tables create sharp images in multiple windows, without user intervention. Embedded SDRAM frame buffers and memory controllers perform frame rate conversion and enhanced video processing completely on-chip. A separate memory is dedicated to storage of on-screen display images and CPU general purpose use. Advanced video processing techniques are supported using the internal frame buffer, including motion adaptive, temporal deinterlacing with film mode detection. When used in combination with the new third-generation scaler, this advanced video processing technology delivers the highest quality video for advanced displays. Both input ports support integrated DVI 1.0 content protection using standard DVI receivers. A new advanced OSD Generator with more colors and larger sizes supports more demanding OSD applications, such as on-screen programming guides. When coupled with the new, faster, integrated microprocessor, this OSD Generator supports advanced OSD animation techniques. Programmable features include the user interface, custom start-up screen, all automatic imaging features, and special screen effects.
Crystal

Video Input Com puter

Video Decoder

PW181
ADC/ TMDS

Display

PW181 System Block Diagram

ROM

Features
Third-generation, two-dimensional filtering techniques Third-generation, advanced scaling techniques Second-generation Automatic Image Optimization Frame rate conversion Video processing On-Screen Display (OSD) On-chip microprocessor JTAG debugger and boundary scan Picture-in-picture (PIP) Multi-region, non-linear scaling Hardware 2-wire serial bus support

Applications
Multimedia Displays Plasma Displays Digital Television
Device
PW181-10V PW181-20V PW181-30V

Application
Up to XGA Displays Up to UXGA Displays Up to WUXGA Display

Package
352 PBGA

PortC PortB PortA (7:0) (7:0) (7:0) PortD(7:0) PortE(7:0) PortF(7:0)

RAMWE, RAMOE, ROMWE, ROMOE

A(19:0), D(15:0), BHEN, CS(1:0), RD, WR

CPUTDO

CPUTMS, CPUTCK, CPUTDI

NMI

EXTINT

RxD, TxD

IRRCVR (1:0)

GPIO

PWM

2-Wire Serial

Processor ROM/ RAM Interface

16-bit Turbo P

Watchdog and Timers

Interrupt Controller

UART

IR Decoders

Microprocessor Bus VRGB (23:0) Horizontal Image Scaler Processor Memory Interface OSD/CPU Memory Controller

VCLK, VPEN, VVS, VHS,

Sync Decoder Auto Image Optimizer Color Space Converter HDCP

Memory Out Bus

Video Port

OSD and CPU SDRAM OSD Memory Bus

CRISP Image Scaler

SDRAM Frame Buffer

Display Port
Image Scaler OSD Control & Blend
Color Matrix, Gamma Correction CLTs, Color Space Expander

RGBE (23:0) RGBO (23:0)

Field Video Deinterlace Frame Buffer Memory Controller

Graphics Port
Sync Decoder Auto Image Optimizer Color Space Converter HDCP Spatial Noise Reduction

Memory In Bus

GCLK, GFBK, GPEN, GVS, GHS, GSOG GRGB (47:0) GCOAST, GREF, GBLKSPL, GHSFOUT

Display Timing Generator MCLK DCLK UCLK Dual PLL Clock Generator

DVS, DHS, DEN, DCLK

Master Reset

PW181 Internal Block Diagram

*For internal clock generator

Reset

MCLKEXT, DCLKEXT, XI* XO*

Figure 1-1 Internal Block Diagram

L6B RECOMMEDED SPARE PARTS

POSITION PART NUMBER 056T27-CH1 056T30-CH1 056W26-LP2 L38172 L57172 UR3110 US1110 US1172 Y23172 Y22172 Y51120 ZG4187F JX1187 ZG4301 ZJ9172 ZJ9205F ZJ9206F ZJ9251F ZJ9805 ZJ9806 ZR1107-AS ZR1172 ZR1204F ZR1205F ZR1208F ZR1212F ZR1251F ZR1255 ZR1258 ZR1805 ZR1806 ZR1910 010844 031383 ZJ9512-AS 303407 303447 054290 054290 452521-01 031508 031477 031478 031423 031479 031795 010844 031358 056708 056708 056010 PART DESCRIPTION LCD CHIMEI V270W1-L04 (LCD TV) LCD CHI-MEI V296W1-L14 (LCD TV) 30") LCD LG-PHILIPS LC260W01-A5K6 (LCD TV) CU ASSY 30'' L6B (ZR1192-21) CU ASSY 27'' L6B (ZR1192-21) L6B CHASIS 27"TOS MS/NX/3/SK/PIP/PEN/DVI L6B CHASIS TOS 30" M/NX/3/SK/PIP/PEN/DVI CU ASSY 30" L6BL38 TOSHIBA (ZR1191-20) CU ASSY 26L6L43 L6B VER.(ZP9191-20) CU ASSY 26L6BL44 (ZG5192-20) L6 CHASIS DAUGHTER BOARD RC L6B TOSHIBA GRI/SHINE SI.P.ED CT-870 R/C L6B REMOTE CONTROL JAECS SIL.GRUNDIG TERMINAL BATT.BOX(+-) R/C TOSHIBA POWER SWITCH ASSY 27/30'' L6B(ZJ9192-20) BACK COVER 30'' L38 LCD TV SILVER L6B SCART BACK COVER 30L38 LCD TV SILVER FRONT COVER G.BL/BUR.SIL P.ED 30L38 TOS. CUSHION LEFT 30" LCD TV CUSHION RIGHT 30" LCD TV SPEAKER 10W 4R PALSTIC CASE KAB MOUNTED CU ASSY 27" L6BL57 TOSHIBA (ZR1191-20) LENS IR/LED 30''L38 LCD TV BACK COVER 27'' L57 LCD TV SILVER L6B KNOB POWER 27"L57 LCD TV SILVER KNOB PROGRAM/VOL. 27LCD TOSHIBA SILVER FRONT COVER G.BL./BUR.SIL P.ED 27L57 TOS BACK COVER DARK GRAY P.ED 27L6BL57 LCD POWER KNOB BURNISH SILVER PAINTED 27"L57 CUSHION LEFT 30" LCD TV CUSHION RIGHT 27" LCD TV ADAPTOR SPS 180W 24/5 12/5 PFC 2PIN(LISH TACT SWITCH 2 LEG (MTSB) CON.DVI 24+5POL JRX1-DV124+5 CABLE PANEL.INTERFACE 30"L6B CHI 30.LU LED ROT LTL 4221N P6 GREEN LED 3MM RED-BLUE LIGITEK LSRFSBK2092 FUSE 5.0A 250V ROUND FUSE 5.0A 250V ROUND IR RECEIVER TSOP34838 SS1A KONN. RF IEC TO RCA KONN. CINCH .... WHITE HOR.12,5MM 30L6 KONN. CINCH ..... RED HOR.12,5MM 30L6 HEADPHONE JACK YKB21-5103 KONN. CINCH ... YELLOW HOR.12,5MM 30L6 KONN.S-VHS TACT SWITCH 2 LEG (MTSB) CONN. VGA B10B SAW FILTER OFW K3958M SAW FILTER OFW K3958M SAW FILTER OFW K9656M

AV/TV CN250 CN601

F450 F451 IR1 J19 J53 J56 J57 J832 J926 MENU P250 SAW825 SAW826 SAW827

SAW828 SW1 TU825 TU826 U1 U150 U151 U2 U250 U251 U3 U350 U351 U400 U401 U402 U450 U452 U454 U455 U456 U457 U458 U50 U51 U52 U650 U750 U825 U826 U827 U925 X941 Y300 Y50 Y550 Y650 Y825 Y826 Y925

056010 010861 Y51136-PH1 Y11136 453124 453195 453350 453262 453261 453261 453494 453921 452997 453233 453263 453349 453095 401372 453294 453294 453428 453124 453124 452706 453352 453351 453346 452863 451569 451569 453271 453124 8R9185 056753 056952 056119 056121 056013 056013 056753

SAW FILTER OFW K9656M ON/OFF SWITCH BK98 TUNER PH UV1316T/SIGH-3 SPL ASIMTRK YAT TUNER HOR.PHILLIPS UV1316/A I H-4 IC-CHIP NCP1117DT33RK TO-252 PACKAGE IC PI5V330W SOIC(W) IC-CHIP PCF8591 /SO16 IC-CHIP AD9887KS-100- DUAL IN.FACE TRAY IC-CHIP 24LC21A-I/SN-CMOS18K/2.5V SE.T&R IC-CHIP 24LC21A-I/SN-CMOS18K/2.5V SE.T&R IC-CHIP TRIPATH TA2024 STEREO CLAS-D T&R IC-CHIP DS90C385A MTD56 IC LM358DR2 / S08 IC-CHIP AM29LV160DB-90EC (TRAY)TSOP48 IC-CHIP AT24C64N-10SI-2. - SO8 TAPE&REEL IC-CHIP TLC7733 /SO8 IC-CHIP NCP1117DTARK (DPAK)(T&R) TO252 TRN FDS9933A IC-CHIP LM2576D2TR4-005V 3A TO263 STPT&R IC-CHIP LM2576D2TR4-005V 3A TO263 STPT&R IC-CHIP LM317MDT VAR.VOLT.REG. TO-252 IC-CHIP NCP1117DT33RK TO-252 PACKAGE IC-CHIP NCP1117DT33RK TO-252 PACKAGE IC TDA1308T/N1 SO-G8 (T&R) IC-CHIP MSP3410-MQFP64 IC TEA6420 /SO28 IC-CHIP PW1231A IC MT48LC4M16A2-7E SDRAM 54PIN TSOP IC-CHIP TDA9886T/V3 118(SO24) T&R IC-CHIP TDA9886T/V3 118(SO24) T&R IC-CHIP TEA6415CDT -VIDEO-MAT-SW.T&R IC-CHIP NCP1117DT33RK TO-252 PACKAGE HP JACK 17"LCD TV CRYSTALL 24.576MHZ 20PF 30PPM CRYSTAL 18.432MHZ +-30PPM CRYSTAL 14.31818MHz CL=18PF30/30PPMHC49U CRYSTAL 10 MHz / HC49U 20PF 30PPM CRYSTAL 4 MHZ HC49-U CRYSTAL 4 MHZ HC49-U CRYSTALL 24.576MHZ 20PF 30PPM

FREQUENCY TABLE (MHz)

Channel
CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH

Number
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44

BG
48.25 55.25 62.25 175.25 182.25 189.25 196.25 203.25 210.25 217.25 224.25 53.75 62.25 82.25 175.25 183.25 192.25 201.25 210.25 471.25 479.25 487.25 495.25 503.25 511.25 519.25 527.25 535.25 543.25 551.25 559.25 567.25 575.25 583.25 591.25 599.25 607.25 615.25 623.25 631.25 639.25 647.25 655.25

I
49.75 59.25 77.25 85.25 93.25 175.25 183.25 191.25 199.25 207.25 215.25 223.25 45.75 53.75 61.75 69.75 95.25

DK
49.75 59.25 77.25 85.25 93.25 175.25 183.25 191.25 199.25 207.25 215.25 223.25

L/L'
47.75 55.75 60.50 63.75 176.00 184.00 192.00 200.00 208.00 216.00 189.25 182.25 196.25 210.25

471.25 479.25 487.25 495.25 503.25 511.25 519.25 527.25 535.25 543.25 551.25 559.25 567.25 575.25 583.25 591.25 599.25 607.25 615.25 623.25 631.25 639.25 647.25 655.25

471.25 479.25 487.25 495.25 503.25 511.25 519.25 527.25 535.25 543.25 551.25 559.25 567.25 575.25 583.25 591.25 599.25 607.25 615.25 623.25 631.25 639.25 647.25 655.25

471.25 479.25 487.25 495.25 503.25 511.25 519.25 527.25 535.25 543.25 551.25 559.25 567.25 575.25 583.25 591.25 599.25 607.25 615.25 623.25 631.25 639.25 647.25 655.25

Channel
CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH S S S S S S S S S S S S S S

Number
45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 1 2 3 4 5 6 7 8 9 10 11 12 13 14

BG
663.25 671.25 679.25 687.25 695.25 703.25 711.25 719.25 727.25 735.25 743.25 751.25 759.25 767.25 775.25 783.25 791.25 799.25 807.25 815.25 823.25 831.25 839.25 847.25 855.25

I
663.25 671.25 679.25 687.25 695.25 703.25 711.25 719.25 727.25 735.25 743.25 751.25 759.25 767.25 775.25 783.25 791.25 799.25 807.25 815.25 823.25 831.25 839.25 847.25 855.25 863,25 871,25 879,25 887,25

DK
663.25 671.25 679.25 687.25 695.25 703.25 711.25 719.25 727.25 735.25 743.25 751.25 759.25 767.25 775.25 783.25 791.25 799.25 807.25 815.25 823.25 831.25 839.25 847.25 855.25

L/L'
663.25 671.25 679.25 687.25 695.25 703.25 711.25 719.25 727.25 735.25 743.25 751.25 759.25 767.25 775.25 783.25 791.25 799.25 807.25 815.25 823.25 831.25 839.25 847.25 855.25 863.25

69.25 76.25 83.25 90.25 97.25 59.25 93.25 105.25 112.25 119.25 126.25 133.25 140.25 147.25 154.25 161.25 168.25 231.25 238.25 245.25 252.25

103.25 111.25 119.25 127.25 135.25 143.25 151.25 159.25 167.25 231.25 239.25 247.25 255.25 263.25

103.25 111.25 119.25 127.25 135.25 143.25 151.25 159.25 167.25 231.25 239.25 247.25 255.25 263.25

160.00 172.00 220.00 232.00 244.00 256.00 268.00 280.00 116.75 128.75 140.75 152.75 164.75 176.75 188.75 200.75 212.75 224.75 236.75 248.75 260.75 272.75

Channel
S S S S S S S S S S S S S S S S S S S S S S S S S S S

Number
15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41

BG
259.25 266.25 273.25 280.25 287.25 294.25 303.25 311.25 319.25 327.25 335.25 343.25 351.25 359.25 367.25 375.25 383.25 391.25 399.25 407.25 415.25 423.25 431.25 439.25 447.25 455.25 463.25

I
271.25 279.25 287.25 295.25 303.25

DK
271.25 279.25 287.25 295.25 303.25

L/L'
284.75 296.75 55.75 60.50 63.75 303.25 311.25 319.25 327.25 335.25 343.25 351.25 359.25 367.25 375.25 383.25 391.25 399.25 407.25 415.25 423.25 431.25 439.25 447.25 455.25 463.25

311.25 319.25 327.25 335.25 343.25 351.25 359.25 367.25 375.25 383.25 391.25 399.25 407.25 415.25 423.25 431.25 439.25 447.25 455.25 463.25

311.25 319.25 327.25 335.25 343.25 351.25 359.25 367.25 375.25 383.25 391.25 399.25 407.25 415.25 423.25 431.25 439.25 447.25 455.25 463.25