HS-PX497 AK,AE,AH

RTV servis Horvat

Tel: ++385-31-856-637
Tel/fax: ++385-31-856-139
Mob: 098-788-319
www.rtv-horvat-dj.hr

SERVICE MANUAL
STEREO CASSETTE PLAYER BASIC TAPE MECHANISM : 6ZM-2 P9NF

N
SIO

S/M Code No. 09-995-410-7R1

VI
RE
 SPECIFICATIONS
Maximum output: 4 mW + 4 mW (EIAJ/16 ohms)<AK,AE>
4 mW + 4 mW (EIAJ/32 ohms)<AH>
Load impedance: 16 – 32 ohms
Power source: DC 1.2V using supplied rechargeable battery, DC 1.5 V using an
R6 (AA) dry cell battery, AC house current using the optional AC
adaptor
Battery life
(EIAJ 1 mW output): Aprox. 8 hours using the rechargeable battery with 4 hours recharging,
Aprox. 30 hours using an LR6 (AA) alkaline battery
Maximum dimensions: 111.4 (W) x 80.7 (H) x 29.1 (D) mm
(41/2 x 31/4 x 13/16in.)
Weight Approx.132g (4.6 oz) (excluding batteries)

• Dolby noise reduction manufactured under license from Dolby

Laboratories Licensing Corporation.
“DOLBY” and the double-D symbol are trademarks of Dolby
Laboratories Licensing Corporation.

• Design and specifications are subject to change without

notice.

ACCESSORIES / PACKAGE LIST

REF. NO. PART NO. KANRI DESCRIPTION
NO.
1 8Z-HK6-908-010 IB,EZ(DPHMCZ) S<AE>
1 8Z-HK6-907-010 IB,EZ(EGFSI) S<AK,AE>
1 8Z-HK6-905-010 IB,H(ECK)S<AH>
2 87-B30-253-010 HEADPHONE,HP-M041
3 8Z-HK6-951-010 RC UNIT,RC497

4 87-047-153-110 BAT,NB-3A PH
5 87-B30-134-010 CHARGER,RB-N01ENC<AE>
5 87-B30-135-010 CHARGER,RB-N01HNC<AH>
5 87-B30-153-010 CHARGER,RB-N01KNC<AK>

TRANSISTOR ILLUSTRATION

B
E

DTA114YU DTC144TU
DTA143TU 2SA1362GR
DTA144TU 2SC4116GR
DTC114TU 2SC3326B
DTC143TU

2
 ELECTRICAL MAIN PARTS LIST
REF. NO. PART NO. KANRI DESCRIPTION REF. NO. PART NO. KANRI DESCRIPTION REF. NO. PART NO. KANRI DESCRIPTION REF. NO. PART NO. KANRI DESCRIPTION
NO. NO. NO. NO.
IC C149 87-016-286-080 C-CAP,TN 2.2-6.3 F93 X801 87-A70-079-110 VIB,XTAL 32.768KHZ M VT-
C150 87-016-288-080 C-CAP,TN 4.7-6.3 F93
87-A21-174-010 C-IC,TA2103F C151 87-010-784-080 C-CAP,U 0.012-25 B
87-A20-961-040 C-IC,MM1279XV C152 87-010-784-080 C-CAP,U 0.012-25 B HEAD FLEX C.B
87-A20-785-080 C-IC,S-81215SG-QK-T1 C153 87-A11-056-080 C-CAP,U 1-10 Z F
8Z-HK6-605-010 C-IC,MSM6576-99-GS-K PH1 87-HK5-608-010 HEAD, ASSY 6ZM-2(MVA)
C154 87-A11-056-080 C-CAP,U 1-10 Z F
C181 87-A10-263-080 C-CAP,U 0.1-16ZF
TRANSISTOR C182 87-A10-263-080 C-CAP,U 0.1-16ZF
C183 87-012-284-080 CAP, U 6800P-50
89-113-625-080 C-TR,2SA1362GR C184 87-012-284-080 CAP, U 6800P-50
87-026-352-080 C-TR,DTC144TU CHIP RESISTOR PART CODE
87-026-331-080 C-TR,DTA114YU C185 87-A11-062-080 C-CAP,S 2.2-16 Z F
87-026-350-080 C-TR,DTC114TU C401 87-012-286-080 CAP, U 0.01-25
89-341-165-080 C-TR,2SC4116GR C402 87-012-286-080 CAP, U 0.01-25 Chip Resistor Part Coding
C403 87-012-286-080 CAP, U 0.01-25
89-333-266-080 C-TR,2SC3326B C405 87-A10-707-080 C-CAP,U 0.47U-16 F Z 8 8
87-026-334-080 C-TR,DTA143TU
87-026-337-080 C-TR,DTA144TU C406 87-A10-025-080 C-CAP,U 0.22-16Z F
87-026-349-080 C-TR,DTC143TU C407 87-A10-263-080 C-CAP,U 0.1-16ZF A
C408 87-A10-950-080 C-CAP,S 4.7-10 Z F Figure
C409 87-A10-260-080 C-CAP,U 0.1-16 K B Resistor Code
DIODE C701 87-010-746-080 CAP, TANTAL 10-4 Value of resistor
87-A40-642-040 C-DIODE,1SS367 C702 87-010-746-080 CAP, TANTAL 10-4
C703 87-A10-263-080 C-CAP,U 0.1-16ZF Chip resistor
C801 87-A11-056-080 C-CAP,U 1-10 Z F Dimensions (mm) : A
MAIN C.B C802 87-A11-056-080 C-CAP,U 1-10 Z F Wattage Type Tolerance Symbol Form L W t Resistor Code : A
C803 87-A11-056-080 C-CAP,U 1-10 Z F 1/16W 1005 5% CJ 1.0 0.5 0.35 104
C101 87-012-273-080 C-CAP,U 820P-50 B
L
C102 87-012-273-080 C-CAP,U 820P-50 B C805 87-010-274-080 C-CAP,TN 3.3-4 1/16W 1608 5% CJ t 1.6 0.8 0.45 108
C103 87-012-273-080 C-CAP,U 820P-50 B C807 87-012-274-080 CHIP CAP,U 1000P-50B
C104 87-012-273-080 C-CAP,U 820P-50 B C808 87-A10-263-080 C-CAP,U 0.1-16ZF 1/10W 2125 5% CJ W 2 1.25 0.45 118
C105 87-016-286-080 C-CAP,TN 2.2-6.3 F93 C901 87-A11-056-080 C-CAP,U 1-10 Z F 1/8W 3216 5% CJ 3.2 1.6 0.55 128
J101 87-099-575-010 JACK,3.5ST BLK 5P
C106 87-016-286-080 C-CAP,TN 2.2-6.3 F93
C107 87-016-114-080 C-CAP,U0.01-25B J901 87-A60-319-010 JACK,DC DIA 2.75
C108 87-016-114-080 C-CAP,U0.01-25B LED601 87-A40-643-040 C-LED,SML-211UT
C109 87-010-828-080 CHIP CAPACITOR,U 0.033- PS501 87-A90-526-010 SNSR,NJL 5163-F1-B
C110 87-010-828-080 CHIP CAPACITOR,U 0.033- R101 87-022-279-080 C-RES,U 470-1/16W F
R102 87-022-279-080 C-RES,U 470-1/16W F
C111 87-A11-056-080 C-CAP,U 1-10 Z F
C112 87-A11-056-080 C-CAP,U 1-10 Z F R107 87-022-243-080 CHIP RES,U 15K-1/16W F
C113 87-010-987-080 C-CAP,S 1500P-50 CH R108 87-022-243-080 CHIP RES,U 15K-1/16W F
C114 87-010-987-080 C-CAP,S 1500P-50 CH R109 87-022-292-080 CHIP RES U 330K-1/16W F
C115 87-012-285-080 C-CAP,U 8200P-50 B R110 87-022-292-080 CHIP RES U 330K-1/16W F IC BLOCK DIAGRAM
R115 87-022-251-080 C-RES,U 33K-1/16W F
C116 87-012-285-080 C-CAP,U 8200P-50 B IC, MM1279XV
C117 87-012-286-080 CAP, U 0.01-25 R116 87-022-251-080 C-RES,U 33K-1/16W F
C118 87-012-286-080 CAP, U 0.01-25 R117 87-022-251-080 C-RES,U 33K-1/16W F
C119 87-A10-828-080 C-CAP,U 0.33-6.3 K B R118 87-022-251-080 C-RES,U 33K-1/16W F
C120 87-A10-828-080 C-CAP,U 0.33-6.3 K B R119 87-022-216-080 C-RES,U 1.1K-1/16W F
R120 87-022-216-080 C-RES,U 1.1K-1/16W F
C121 87-A10-827-080 C-CAP,U 0.47-6.3 K B
C122 87-A10-827-080 C-CAP,U 0.47-6.3 K B R121 87-022-241-080 CHIP RESTOR 12K 1/16W F
C123 87-A11-056-080 C-CAP,U 1-10 Z F R122 87-022-241-080 CHIP RESTOR 12K 1/16W F
C124 87-A11-056-080 C-CAP,U 1-10 Z F R123 87-022-293-080 CHIP RES U 390K-1/16W F
C125 87-A11-056-080 C-CAP,U 1-10 Z F R124 87-022-293-080 CHIP RES U 390K-1/16W F
R129 87-022-254-080 C-RES,U 43K-1/16 WF
C126 87-A11-056-080 C-CAP,U 1-10 Z F
C127 87-012-274-080 CHIP CAP,U 1000P-50B R137 87-022-223-080 CHIP RES 2.2K 1/16W F
C128 87-012-274-080 CHIP CAP,U 1000P-50B R804 87-022-255-080 C-RES,U 47K-1/16W F
C129 87-A10-025-080 C-CAP,U 0.22-16Z F R807 87-022-292-080 CHIP RES U 330K-1/16W F
C130 87-A10-025-080 C-CAP,U 0.22-16Z F R810 87-022-292-080 CHIP RES U 330K-1/16W F
R811 87-022-292-080 CHIP RES U 330K-1/16W F
C131 87-016-429-080 C-CAP,E 100-4 5.5N
C132 87-016-429-080 C-CAP,E 100-4 5.5N R814 87-022-292-080 CHIP RES U 330K-1/16W F
C133 87-A11-056-080 C-CAP,U 1-10 Z F R821 87-022-292-080 CHIP RES U 330K-1/16W F
C134 87-010-746-080 CAP, TANTAL 10-4 S101 87-A90-330-080 C-SW,SL 1-1-2 SSSS81
C135 87-A10-952-080 C-CAP,TN 22-4 M A MCM S102 87-A90-330-080 C-SW,SL 1-1-2 SSSS81
S103 87-A90-400-080 C-SW,SL 1-1-4 SSSS81
C136 87-016-288-080 C-CAP,TN 4.7-6.3 F93
C137 87-A10-952-080 C-CAP,TN 22-4 M A MCM S801 87-A90-455-010 SW,PUSH HXW4001
C138 87-A10-025-080 C-CAP,U 0.22-16Z F S802 87-A90-356-210 SW,LEAF 6ZM-2
C139 87-A10-025-080 C-CAP,U 0.22-16Z F S803 87-A90-665-180 C-SW,TACT LS7A2M
C140 87-016-288-080 C-CAP,TN 4.7-6.3 F93 S804 87-A90-665-180 C-SW,TACT LS7A2M
S805 87-A90-665-180 C-SW,TACT LS7A2M
C141 87-A10-707-080 C-CAP,U 0.47U-16 F Z
C142 87-A10-707-080 C-CAP,U 0.47U-16 F Z S806 87-A90-665-180 C-SW,TACT LS7A2M
C143 87-A10-707-080 C-CAP,U 0.47U-16 F Z S807 87-036-373-080 C-SW,SLIDE 1-1-2(E)
C144 87-A11-056-080 C-CAP,U 1-10 Z F S808 87-A90-330-080 C-SW,SL 1-1-2 SSSS81
C145 87-A11-056-080 C-CAP,U 1-10 Z F S809 87-A91-335-080 C-SW,PUSH 1-1-1 SPVG11
SFR401 87-024-406-080 C-SFR,6.8K RH03A3A
C146 87-A11-056-080 C-CAP,U 1-10 Z F
C147 87-A10-708-080 C-CAP,U 0.68U-10 F Z TH401 87-A90-855-080 C-THMS,SC20-3K102K
C148 87-016-288-080 C-CAP,TN 4.7-6.3 F93 VR101 87-A90-116-080 C-VR,RTRY20KCX2V0103

3 4

ZHK6.A3.p65 1 5/12/99, 2:59 PM

 WIRING - 1 (MAIN)
14 13 12 11 10 9 8 7 6 5 4 3 2 1 1 2 3 4 5 6 7 8 9 10 11 12 13 14

A A

B B

C C

D D

E E

F F

G G

H H

I I

J J

K K

L L

M M

N N

O O

P P

Q Q

R R

S S

T T

U U

5 6

ZHK6.A3.p65 2 5/12/99, 3:00 PM

SCHEMATIC DIAGRAM - 1 (MAIN)

OFF

ON

7 8
 IC DESCRIPTION ADJUSTMENT
IC, MSM6576-99-GS-K

A MAIN C.B
Pin No. Pin Name I/O Description
2
1 HOLD I ‘H’: Normal operation, ‘L’: Hold key (main unit side). SFR 401
1 GND
2 BLS/REV MODE I ‘H’ :Endless and BLS ON, ‘L’ :One cyde and BLS OFF. 2
3 DOLBY SW I ‘H’: Dolby ON, ‘L’: Dolby OFF. PHONES J101 1
TP1
4 RESET I Reset input terminal. IC801
(R-CH)
TP2
5~7 TEST1 ~ TEST3 - Test terminal (connected to ground). (L-CH)

8 BRAKE O ‘H’: Brake ON, ‘L” :Brake OFF. 2 4

VR101

9 MOT HI O ‘H’: High speed, ‘L’: Normal speed.

1 3
10 MOT DIR O ‘H” :Clockwise direction, ‘L’ :Counterclockwise direction. IC101
VOLUME
11 MOT ON O ‘H’: Motor ON, ‘L’: Motor OFF.
12 POP I ‘H’: POP ON, ‘L’: POP OFF. 2
13 JAZZ I 'H' : JAZZ OFF, 'L' : JAZZ ON.
14 ROCK I 'H' : ROCK OFF, 'L' : ROCK ON.
15, 16 XTB, XT - Crystal oscillator terminal.
17 VDD - Power supply terminal. <TAPE PLAYER SECTION> PRACTICAL SERVICE FIGURE
18, 21 VSS1, VSS2 - Ground terminal.
1. Tape Speed Adjustment <TAPE SECTION>
19, 20 VCM, VCP - Internal electronic potential generator terminal. Settings : • Test tape : TTA – 100 (Tape center) Tape speed : 3015Hz ± 50Hz
22 VEE - Power supply terminal for internal logic. • Test point : Phones Jack (J101) Wow : Less than 0.52% (RMS)
• Adjustment location : SFR401 Take-up torque : 20 ~ 30g-cm (FWD,REV)
23 L. V. STOP1 I Reference input terminal for detection of reduce volatage stop. • Dolby NR : OFF F.F torque : 70 ~ 150g-cm
• MSP : CLASSIC Rew torque : 70 ~ 150g-cm
24 L. V. STOP2 I Signal input terminal for detection of reduce volatage stop.
• Direction : FWD Back tension : 1 ~ 3g-cm (FWD,REV)
25 REMOTE I Key input (remote controller side). • Tape selector : NORM S/N ratio : More than 42dB(PB,DC)
• Volume : MAX Distortion : Less than 3.0%(PB,DC)
26 P-SNSR I Photo sensor input. Method : Play back the test tape and adjust SFR401 so that Noise level : Less than 3.0mV
27 BUZR O Alarm sound output. the frequency becomes 3015Hz ± 10Hz. Then (Vol MAX, PB,DC)
confirm WOW is less than 0.55%. Less than 0.3mV
28 MID O ‘H’ :When POP mode, ‘L’ :When not POP mode.
(Vol MIN, PB,DC)
29 DIS CH O ‘H’ :When DIS CH, ‘L’ :When normal. 2. Dolby Level Adjustment Frequency response : 63Hz + 3/– 5dB ~
Setting : • Test tape : TTA – 200 8kHz + 4/– 4dB
30 BASS O ‘H’ :When ROCK, JAZZ mode, ‘L’ :When not ROCK, JAZZ mode. • Test point : TP1(Rch),TP2(Lch),GND (NORM)
• Direction : FWD 63Hz + 3/– 5dB ~
31 MS IN I ‘H’ :Exist tune, ‘L’ :Not exist tune.
• Tape selector : NORM 10kHz + 4/– 4dB
32 POWER ON O ‘H’ :Power ON, ‘L’ :Power OFF. • Dolby NR : OFF (METAL)
• Volume : MIN "0" Test tape : TTA – 100
33 LED CONT O Photo sensor LED control terminal.
• Adjustment points : Soldered patterns 1 – 4 TTA – 200
34 F/R CTRL O ‘H’ :FWD, ‘L’ :REV. Procedure : Short the patterns via solder as showen in the TTA – 210
table so the Dolby NR level is 24.5mV ± 1.0dB. TTA – 310 (METAL)
35 MUTE O ‘H’ :Mute OFF, ‘L’ :Mute ON. Adjust so the specifications are satisfied in both TTA – 320 (NORM)
36 C-SW I ‘H’: Exist cassette tape, ‘L’: Not exist. the forward and reverse directions. Connect 10µF
/16V coupling capacitors between test points and
37 EJECT SW I ‘H’: Open cassette cover, ‘L’: Close cassette cover. test equipment (connect the positive terminals to
38 TIMING SW I ‘H’ :PLAY, REC PLAY, ‘L’ :No cassette, STOP, FF, REW. the test points).

39 VDD - Power supply terminal. SOLDER PATTERN 1 – 4

STANDARD : 24.5 ± 1.0dB
40 STOP I Stop key input (main unit side).
41 PLAY I Play key input (main unit side). SHORT OPEN +
42 FF I FF key input (main unit side). 1 only +1dB

43 REW I REW key input (main unit side). Lch 3 only +1.5dB
1 and 3 +2.5dB
44 JACK IN I ‘H’ :Disable remote controller key input, ‘L’ :Able input.
2 only +1dB
Rch 4 only +1.5dB
2 and 4 +2.5dB

9 10

ZHK6.A3.p65 3 5/12/99, 3:00 PM

 MECHANICAL EXPLODED VIEW 1/1 MECHANICAL PARTS LIST 1/1
REF. NO. PART NO. KANRI DESCRIPTION REF. NO. PART NO. KANRI DESCRIPTION REF. NO. PART NO. KANRI DESCRIPTION REF. NO. PART NO. KANRI DESCRIPTION
NO. NO. NO. NO.
1 8Z-HK6-001-010 LID,CASS N 21 8Z-HK6-208-010 HLDR,BATT
2 8Z-HK6-203-010 HLDR,CASS L A 87-067-738-010 HINGE SCREW 1.4-1 BLK N
3 8Z-HK6-207-010 SPR-P,CLIK B 8Z-HK6-223-010 S-SCREW,+1.4-0.7-1 CR NL
4 8Z-HK6-202-010 HLDR,CASS R C 87-078-113-010 S-SCRW,+1.4-3.5 HL(B
B 5 8Z-HK6-008-010 WINDOW,CASS N D 87-067-746-010 SCREW,M 1.4-2(H0.5)

17 6 8Z-HK6-005-010 LID,BATT 497 N E 8Z-HK6-224-010 S-SCREW,SERR+1.4-3 CR

16 H 7 8Z-HK6-011-010 KNOB,SL HOLD F 87-067-535-010 SCREW VT+1.4-3.5
8 8Z-HK6-001-010 LID,ASSY CASS N G 87-HK5-237-010 S-SCREW,1.4-2 CR NL
9 8Z-HK6-012-010 KNOB,SL A H 87-067-732-010 TAPPING SCREW, VT1.4-3
19 10 8Z-HK6-013-010 KNOB,SL B I 87-067-384-010 SCREWVT1.4-3.5HL

18 K 11 8Z-HK6-213-010 SPR-C,BATT M J 88-HK5-228-010 S-SCREW,+1.4-2 CR

12 8Z-HK6-212-010 PLATE,BATT P K 87-263-500-310 SCREW V+1.4-1.4
13 8Z-HK6-225-010 SPR-E,EJECT L L 87-HK5-235-010 S-SCREW,1.4-0.6-2.5
15 A 20 14 8Z-HK6-204-010 PLATE,EJECT M 87-067-430-010 VT1.4-5 BLK
15 8Z-HK6-010-010 KNOB,SL OPEN
H J
I 16 8Z-HK6-004-010 FRAME,CENTER N
JACK 3.5 17 87-HK6-203-010 SPR-P,POP UP
18 8Z-HK6-205-010 HLDR,JACK
BLK ST 19 8Z-HK6-206-010 SPR-P,CASS
13 W/O SW 5P 20 8Z-HK6-201-010 PLATE,HINGE
14 M M
SH SHIELD L
I
HEAD 21

6ZM-2 P9NF I

G 1 COLOR NAME TABLE

Basic color Color Basic color Color Basic color Color
D symbol symbol symbol
B Black C Cream D Orange
G Green H Gray L Blue
LT Transparent Blue N Gold P Pink
G R Red S Silver ST Titan Silver
P.C.B T Brown V Violet W White
3 WT Transparent White Y Yellow YT Transparent Yellow
LM Metallic Blue LL Light Blue GT Transparent Green
4 LD Dark Blue DT Transparent Orange
C
12
2

11 5
10 6
E
9 E

E
8

11 12

ZHK6.A3.p65 4 5/12/99, 3:00 PM

 TAPE MECHANISM EXPLODED VIEW 1 / 1 TAPE MECHANISM PARTS LIST 1/1
REF. NO. PART NO. KANRI DESCRIPTION REF. NO. PART NO. KANRI DESCRIPTION REF. NO. PART NO. KANRI DESCRIPTION REF. NO. PART NO. KANRI DESCRIPTION
NO. NO. NO. NO.
1 86-ZM2-255-010 SPR-T,PIN BACK L 32 86-ZM2-276-010 PULLEY,COUPLER
F 2 86-ZM2-252-610 GUIDE,TAPE 33 86-ZM2-212-310 SHAFT,FR
HEAD FLEX C.B 3 86-ZM2-220-210 SPR-T,HEAD 34 86-ZM2-214-510 LEVER,CAM R
4 86-ZM2-219-510 LEVER,HEAD 35 86-ZM2-215-210 SPR-E,CAM R
42 5 86-ZM2-347-010 LEVER,MS EJECT 36 86-ZM2-222-410 LEVER,PIN UP R

6 86-ZM2-226-110 ROLLER ASSY,PINCH 37 86-ZM2-218-310 LEVER,HEAD UP

5 7 86-ZM2-254-010 SPR-T,PIN BACK 38 86-ZM2-205-410 FLY-WHL,L
8 86-ZM2-230-110 SPR-T,PINCH L 39 86-ZM2-330-010 FLY-WHL,R2
9 86-ZM2-229-110 SPR-T,PINCH R 40 86-ZM2-282-010 SH,AUTO 2
10 86-ZM2-240-110 CAP,REEL 41 86-ZM2-225-310 ARM,PINCH L
6
11 86-ZM2-234-110 SHAFT,REEL R 42 86-ZM2-224-210 ARM,PINCH R
12 86-ZM2-251-310 SHAFT,GEAR B 43 86-ZM2-283-210 CAP,SHAFT
7 13 86-ZM2-201-E10 CHAS ASSY,OUT-SERT 44 86-ZM2-275-310 CAP,SLIP R
2 14 86-ZM2-349-010 SPR-E,EJECT 45 86-ZM2-210-710 LEVER,FR
9 15 86-ZM2-232-310 LEVER,REEL R 46 86-ZM2-211-210 GEAR,FR
41
3
16 86-ZM2-268-310 SHAFT,PULLEY BELT 2 47 86-ZM2-213-210 SPR-C,FR
a
b 17 86-ZM2-243-310 SPR-C,BT 48 M8-7ZS-690-000 ABL-76 A
18 86-ZM2-329-210 BELT,P5 49 86-ZM2-221-010 CLR,BRG N
4 19 86-ZM2-209-310 GEAR,B 50 86-ZM2-239-010 FELT,
1 SH,1.2-2.9-0.25SL 20 86-ZM2-238-710 GEAR,FF 51 86-ZM2-342-010 LEVER ASSY,EJECT
43
6 d 21 86-ZM2-245-410 SPR-C,SLIP L 52 86-ZS2-312-010 SPR-P,6A-MOT
8
43 22 86-ZM2-237-010 GEAR,PLAY 53 87-ZS6-301-010 COIL,FP 7ZS6
11 23 86-ZM2-241-310 SPR-C,SLIP R 54 86-ZM2-206-310 SHAFT,CAPSTAN
SH,1.2-2.9-0.25SL 10 24 86-ZM2-272-010 LEVER,SW P 8.4 A 86-ZM2-278-010 W-P,1.36-4-0.2 SLT
c 25 86-ZM2-236-510 CAP,SLIP B 86-ZM2-319-010 W-L,0.95-3-0.35
13 26 86-ZM2-235-210 SHAFT,REEL L C 87-067-860-010 PW,3-0.95-0.4
27 86-ZM2-223-310 LEVER,PIN UP L D 87-067-516-010 PW,3-1.58-0.25,SLIT
c 28 86-ZM2-233-310 LEVER,REEL L E 87-067-430-010 VT1.4-5 BLK
29 86-ZM2-208-310 GEAR,A F 86-ZM2-348-010 S-SCREW,+1.4-4.6
b 30 86-ZM2-217-210 SPR-E,CAM L G 87-067-815-110 VT+1.4-3(HL)
d e
31 86-ZM2-216-510 LEVER,CAM L

a
51 30
G
g
g
e 14 28

27 48
29 53
20 15
f
21 C
16
22 31
32
50 24
B HLDR,FP
25 49 C
52 G
17 54 35
f 34 20
37 E
38 23 PLATE,THRUST
26 45 B
49
22
46
50
40 36
12 47 54
44
33
19 17
A
39
18
D

13 14

ZHK6.A3.p65 5 5/12/99, 3:00 PM

SPRING APPLICATION POSITION

86-ZM2-243-310
86-ZM2-243-310
SPR-C,BT
SPR-C,BT

86-ZM2-245-410 86-ZM2-241-310
86-ZM2-213-210 SPR-C,SLIP R
SPR-C,SLIP L SPR-C,FR

C0.3

86-ZM2-217-210 86-ZM2-220-210
86-ZM2-215-210
SPR-E,CAM L SPR-T,HEAD
SPR-E,CAM R

86-ZM2-230-110
86-ZM2-255-010 86-ZM2-229-110
SPR-T,PINCH L
86-ZM2-254-010 SPR-T,PINCH R
SPR-T,PIN BACK L
SPR-T,PIN BACK

15
 L

A4

2–11, IKENOHATA 1–CHOME, TAITO-KU, TOKYO 110, JAPAN TEL:03 (3827) 3111
9630469 931261 Printed in Singapore