Scribd Logo
Upload

Welcome to Scribd!

  • 3K views

    Trelleborg Piping SPEC. REV C

    Uploaded by

    SIVA
    All flanges are available in FF Hazen-Williams C-factor is 155 and recommended maximumseawater velocity in pipes is 10 m / s for both continous and intermittent flow. All fittings / branches are available with connection for heat tracing Type of gaskets may vary according to client spesification.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd

    Trelleborg Piping SPEC. REV C

    Uploaded by

    SIVA
    3K views1 page
    All flanges are available in FF Hazen-Williams C-factor is 155 and recommended maximumseawater velocity in pipes is 10 m / s for both continous and intermittent flow. All fittings / branches are available with connection for heat tracing Type of gaskets may vary according to client spesification.

    Copyright

    © Attribution Non-Commercial (BY-NC)

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    All flanges are available in FF Hazen-Williams C-factor is 155 and recommended maximumseawater velocity in pipes is 10 m / s for both continous and intermittent flow. All fittings / branches are available with connection for heat tracing Type of gaskets may vary according to client spesification.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    3K views1 page

    Trelleborg Piping SPEC. REV C

    Uploaded by

    SIVA
    All flanges are available in FF Hazen-Williams C-factor is 155 and recommended maximumseawater velocity in pipes is 10 m / s for both continous and intermittent flow. All fittings / branches are available with connection for heat tracing Type of gaskets may vary according to client spesification.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 1

    Title

    Doc.no.

    Operator

    Sec.no. Rev.no. Rev.date Page: Of:

    Piping and Valve Specification Piping Class Sheet:


    DESIGN CODE:
    Maximum Design Pressure: At Temperature:

    89101-002
    Project

    ELASTOPIPE
    ASME B31.3
    Barg C

    CL150
    Corr. Allow:
    20,0 -29 20,0 70

    C
    NONE Service Code:

    26.05.2004

    FIREWATER (fresh/sea)

    PIPE SIZE AND WALL THICKNESS


    Nom.Size(in) 1 1.5 2 3 4 6 8 25 40 50 75 100 150 200 Dia.(mm) Wall th.(mm) 14,00 14,00 14,00 14,25 14,25 17,00 17,00 2,8 3,5 4,4 6,6 8,4 15,0 20,0 Weight (kg) WALL THICKNESS UNDER TOLERANCES: N/A LONGITUDINAL WELD EFFICIENCY: N/A ELEMENT NAME PIPE BENDING FITTINGS BRANCHES FLANGES Note d) FLG. BLIND LINE BLINDS BOLTING DIMENSION STANDARDS NOM. SIZE FROM TO incl incl 1 8 1 8 1 8 1 8 1 8 1 8 1 8 1 8 1 8 TYPE MATERIAL NAME ELASTOPIPE ELASTOPIPE Titanium gr. 2 Titanium gr. 2 Titanium gr. 2 / SS316 Titanium gr. 2 / A153 Titanium gr. 2 Titanium gr. 2 Titanium gr. 2 A193 B7 / A194 2H A320 B8M / A194 8M A320 L7 Note c) Titanium gr. 2 MDS EDS

    Manuf. Std. Bending radius for pipe=5xOD (min) Manuf. Std. Manuf. Std. ASME B16.5 ASME B16.5 ASME B16.5 ASME B16.5 Spect. bl. ASME B16.5 ASME B16.5 ASME B16.21 ASME B16.11 Manuf. Std. VSM NOMINAL SIZE FROM TO incl incl 1 2 3 8 4 8 1 2 3 8 2 1 2 8 2 8 3 8

    GASKET PLUGS/NOZZLE SUPPORTING VALVE OR EQUIPMENT TYPE GATE BUTTERFLY GLOBE CHECK BALL

    4 1 1

    Flex rubberpipe Note a) Note b) Note b) CL150 RF Lapped CL150 RF Lapped CL150 RF WN-Type CL150 RF CL150 FF Studbolts c/w nuts Studbolts c/w nuts 8 Hex head screw 8 1 mm CGF 1.5 Hex head

    T01 T01 T01/S01 T01 T01 T01 NAF2 NAF1 NAF1 NLB1 NBO1 NBO1 NGA2 T01

    VDS

    REMARKS

    GTAT00R GTAT10R BUAT20R GBAT00R GBAT10R CHAT00R CHAT50R BLAT40R BLAT30R

    Full bore Reduced bore

    NOTES:

    a) b)

    c) d) GENERAL: 1) 2)

    For bending radius less than 5xOD, Titan elbows are available All titanium parts to be manufactured acc. to approved manufacturers drawings. For up and include DN 1.5", minimum wall thickness as for schedule 40S. For above DN 1.5", minimum wall thickness as for schedule 10S. All fittings / branches are available with connection for heat tracing Type of gaskets may vary according to client spesification. All flanges are available in FF Hazen-Williams C-factor is 155 and recommended maximumseawater velocity in pipes is 10 m/s for both continious and intermittent flow. The referenced MDS, EDS, VSM and VDS are NORSOK specifications.

    You might also like