Scribd
Upload
363 views21 pages

STAAD - Pro: Department of Civil Engineering, Iit Roorkee

This document provides an introduction and overview of the contents that will be covered in a training course on STAAD.Pro, a structural analysis and design software. The course modules will include introductions to the STAAD interface and file types, geometry creation tools, additional modeling tools like translation and rotation, defining member properties, applying constants, supports and loads, performing analyses, and reviewing results through post-processing tools. The document lists the chapter titles that will be covered in each module to introduce the key areas of the software that the training will address.

Uploaded by

Nayan Fatania
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
363 views21 pages

STAAD - Pro: Department of Civil Engineering, Iit Roorkee

This document provides an introduction and overview of the contents that will be covered in a training course on STAAD.Pro, a structural analysis and design software. The course modules will include introductions to the STAAD interface and file types, geometry creation tools, additional modeling tools like translation and rotation, defining member properties, applying constants, supports and loads, performing analyses, and reviewing results through post-processing tools. The document lists the chapter titles that will be covered in each module to introduce the key areas of the software that the training will address.

Uploaded by

Nayan Fatania
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
You are on page 1/ 21

INTRODUCTION TO

STAAD.Pro
DEPARTMENT OF CIVIL ENGINEERING, IIT ROORKEE

Contents
1.Introduction 2.G o! tr" #.Adition$% too%& 'or Mod %in( ).Pro* rti & +.Con&t$nt& ,&u**ort& $nd ot, r &* ci'ic$tion& -.Lo$din( ..An$%"&i& /.Po&t *roc &&in( 0.D &i(n

Modu% 1 Introduction to STAAD Pro


STAAD So't1$r M t,od o' An$%"&i& St$rtin( STAAD Pro Cr $tin( N 1 Fi% STAAD Pro Scr n O* nin( $nd c%o&in( $ E2i&tin( STAAD Pro 'i% . S$3in( 4 S$3in( A&

Module 2 Geometry
What are Nodes, Beams, and Plates How things are done in the Input file Geometry Creation Methods 1: sing !tru"ture Wi#ard

$: %rafting the Geometry using !nap node


&: sing Copy'Cut with Paste (: sing !preadsheet )*+"el, Copy and Paste -: sing %./ importing file fun"tion

Module 3 Additional tools for modeling


0ranslational 1epeat Cir"ular 1epeat Mirror 1otate Mo2e Insert Node

3dd Beam Between Mid4Points 3dd Beam 5y Perpendi"ular Interse"tion %elete ndo'1edo 6ooming'Panning %imensioning

Module 4 Properties
Property 0ypes
0ype 1: Prismati"

7iewing Cross4!e"tion
0ype $: Built4In !teel 0a5le 0ype &: 0hi"8ness

General Notes 35out Property 3ssigning

Module 5 Constants, Supports, and Specifications


Material Constants Geometry Constant !upports
How to 3ssign !upports *diting !upports

!pe"ifi"ations

Module 6 Loading
How to Create Primary 9oad : Indi2idual 9oads: !elf weight Mem5ers 3rea 9oad /loor 9oad Plate 9oads Node How to Create Manual Com5inations :

Module

Analysis

Perform 3nalysis Command

Module ! Post Processing


1esults Node %ispla"ement Node 1ea"tions Beam /or"es Beam !tresses Beam Graphs 3nimation ;ther Ways: %ou5le4Cli"8ing a Beam

"eel free to contact#

($ur$3!$roo5(!$i%.co!

r ' r nc

111.r iu&$.co!

You might also like