Scribd
Upload
141 views4 pages

Accelerator Control System

The document provides instructions for removing and installing an accelerator control system. It describes: 1. Disconnecting the accelerator position sensor electrical connector by pulling back the connector lock and pulling up on the connector. 2. Removing the upper accelerator pedal nuts, lower pedal bolt, and the accelerator pedal and position sensor assembly. 3. Installation is done in reverse order, checking for smooth pedal operation and full pedal travel of 52.6-58.2mm. When reconnecting the position sensor, accelerator pedal released position learning must be performed.

Uploaded by

احمد عصام المغربي
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
141 views4 pages

Accelerator Control System

The document provides instructions for removing and installing an accelerator control system. It describes: 1. Disconnecting the accelerator position sensor electrical connector by pulling back the connector lock and pulling up on the connector. 2. Removing the upper accelerator pedal nuts, lower pedal bolt, and the accelerator pedal and position sensor assembly. 3. Installation is done in reverse order, checking for smooth pedal operation and full pedal travel of 52.6-58.2mm. When reconnecting the position sensor, accelerator pedal released position learning must be performed.

Uploaded by

احمد عصام المغربي
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

B ENGINE

ACC
SECTION
ACCELERATOR CONTROL SYSTEM C

E
CONTENTS
ACCELERATOR CONTROL SYSTEM ...................... 2 SERVICE DATA AND SPECIFICATIONS (SDS) ........ 3 F
Removal and Installation .......................................... 2 Accelerator Control ................................................... 3
PEDAL TRAVEL .................................................... 3
G

ACC-1
ACCELERATOR CONTROL SYSTEM

ACCELERATOR CONTROL SYSTEM PFP:18005

Removal and Installation EBS00G42

1. Disconnect the accelerator position sensor electrical connector.


a. Pull the connector lock back to unlock the connector from the
accelerator pedal position sensor as shown.
b. Pull up on the connector to disconnect it from the accelerator
pedal position sensor as shown.

LBIA0333E

2. Remove the upper accelerator pedal nuts and lower accelerator


pedal bolt.
3. Remove the accelerator pedal and accelerator position sensor
assembly.
● For electrical inspection of the accelerator pedal position sen-
sor, refer to EC-603, "ACCELERATOR PEDAL POSITION
SENSOR" and EC-609, "ACCELERATOR PEDAL POSI-
TION SENSOR" and EC-621, "ACCELERATOR PEDAL
POSITION SENSOR" .
CAUTION:
● Do not disassemble the pedal assembly. Do not remove LBIA0334E

the accelerator pedal position sensor from the pedal


assembly.
● Avoid impact from dropping during handling.

● Keep the pedal assembly away from water.

4. Installation is in the reverse order of removal.


● Check the accelerator pedal for smooth operation. There should be no binding or sticking when apply-
ing or releasing the accelerator pedal.
● Check that the accelerator pedal moves through the full spec-
ified distance of pedal travel.
Pedal travel A : 52.6 - 58.2 mm (2.07 - 2.29 in)
CAUTION:
When the harness connector of the accelerator pedal posi-
tion sensor is disconnected, perform the "Accelerator pedal
released position learning". Refer to EC-47, "Accelerator
Pedal Released Position Learning" .

LBIA0062E

ACC-2
SERVICE DATA AND SPECIFICATIONS (SDS)

SERVICE DATA AND SPECIFICATIONS (SDS) PFP:00030


A
Accelerator Control EBS00G43

PEDAL TRAVEL
Accelerator control pedal - total travel 52.6 - 58.2 mm (2.07 - 2.29 in) ACC

ACC-3
SERVICE DATA AND SPECIFICATIONS (SDS)

ACC-4

You might also like