Scribd
Upload
25 views

Structural Design Practice - I: Tutorial Problems

This document contains 5 tutorial problems related to structural design: 1) Design a simply supported slab covering a 4m x 6m room with 10mm thick brick walls using M20 concrete and Fe415 steel. 2) Design the reinforcement in a 400mm x 400mm column subjected to loads and bending moments. 3) Design the reinforcement in a 500mm x 400mm column subjected to axial and biaxial bending loads. 4) Design an isolated footing for a 300mm x 300mm column carrying a service load of 100 kN. 5) Design an isolated footing for a 1000mm x 300mm column carrying loads and moments.

Uploaded by

Rutvik Sheth
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
25 views

Structural Design Practice - I: Tutorial Problems

This document contains 5 tutorial problems related to structural design: 1) Design a simply supported slab covering a 4m x 6m room with 10mm thick brick walls using M20 concrete and Fe415 steel. 2) Design the reinforcement in a 400mm x 400mm column subjected to loads and bending moments. 3) Design the reinforcement in a 500mm x 400mm column subjected to axial and biaxial bending loads. 4) Design an isolated footing for a 300mm x 300mm column carrying a service load of 100 kN. 5) Design an isolated footing for a 1000mm x 300mm column carrying loads and moments.

Uploaded by

Rutvik Sheth
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 1

Structural Design Practice I Tutorial Problems

1. Design a simply supported slab to cover a room with internal dimensions of 4.0m x 6.0m and !0mm thic" bric" walls all around. #ssume a live load of ! "$%m and a floor finish load of 1 "$%m . &se ' 0 concrete and (e41) grade steel. #ssume that slab corners are free to lift up. #ssume mild exposure conditions. . # corner column 4)0mm x 4)0mm located in the lowermost storey of a system of braced frames* is sub+ected to factored loads, Pu - 1)00 "$* 'ux - 1.0 "$m and 'uy - 110 "$m. The unsupported length of the column is !.)0m. Design the reinforcement in column* assuming ' ) concrete and (e41) steel. !. Design the reinforcement for a braced column* !00mm x 4)0mm sub+ected to a factored axial load of 14)0 "$ and factored moments of /0 "$m and 4) "$m with respect to ma+or and minor axis respectively at the top end. #ssume that the column is bent in double curvature in both directions with the moments at the bottom e0ual to )01 of the corresponding moments at top. #ssume an unsupported length of /.0m and an effective length ratio of 0.20 in both directions. &se '!0 concrete and (e41) steel. 4. Design an isolated footing for a s0uare column* )00mm x )00mm* carrying a service load of )00 "$. #ssume soil with a safe bearing capacity of ! ) "$%m at a depth of 1.)m below ground. #ssume ' ) grade concrete and (e41) steel for the footing. ). Design an isolated footing for a s0uare column* !00mm x )00mm* carrying a factored axial load Pu - 1000 "$ and a factored uniaxial moment 'ux - 1 0 "$m with respect to ma+or axis at the column base. #ssume soil with a safe bearing capacity of 00 "$%m at a depth of 1. )m below ground. #ssume ' ) grade concrete and (e41) steel for the footing.

You might also like