Apexi Installtion Instruction Manual: S-AFC 2 / SUPER AIR FLOW CONVERTER WIRING DIAGRAM

SUPER
AIRFLOW CONVERTER
SUPER AIR FLOW CONVERTERⅡ
WIRING DIAGRAM BY MODEL
SUPER
AIRFLOW CONVERTER
This document describes car models to which the Super Airflow

Converter (Product code: 401-A911/401-A913) is applicable, and
ECU terminal arrangement drawings. For the operating method
and precautions for the Super Airflow Converter, refer to the
Instruction Manual.
When installing the Super Airflow Converter, both this document
and the Instruction Manual are required.
Even if the car model and manufacturing year coincide with the
contents described in this document, this product may not be
installed in certain specification vehicles or remodeled vehicles.
The manufacturing years of applicable vehicles are as of January,
2005. For the latest vehicles applications, Please contact your
local APEXERA Office or dealer for more information.
1
■Contents
■Introduction _________________________________________________P3
■Precaution on Installation___________________________________P4
■Installation __________________________________________________P6
■ECU Arrangement Diagram__________________________________P12

■How to Refer to the ECU Terminal Arrangement Diagram _P13
■TOYOTA
Table of Applicable Models ...............................P14
ECU Terminal Arrangement Table .......................P22
■NISSAN
Table of Applicable Models...................................................... P28
■HONDA
■MITSUBISHI
■MAZDA
■SUBARU
■SUZUKI
■DAIHATSU
2
■Introduction
“Safety precautions” are described in the Instruction Manual.
Please read them before starting installation work.
“Signal words and their meanings” are described in the
Instruction Manual for this product. The “Electronic Control Unit”
is abbreviated as “ECU” in this document.
！ CAUTION
●Entrust an experienced professional with the installation work of this
product.
After completion of the installation, hand over this document, Instruction Manual, and
Warranty to the customer (user)
●Do not pull the harness of the vehicle and the harness of this product.
This may cause wire damage or short circuits, resulting in damage to the product and
vehicle.
●When removing or connecting a connector, be sure to unlock the

locked (claw) status beforehand.
When the connector is provided with a securing bolt, loosen this bolt
completely before pulling out the connector
Failure to do so may damage the connector.
●Keep the harness of this product and vehicle harness away from high
temperatures and moving parts. Also, Keep this harness away from
water.
Failure to do so may result in cut wires or short circuits that can lead to vehicle and
product damage.
●Do not route the harness of this product and the harness of the vehicle
near a sharp-edges. Do not insert the harness between objects by
applying pressure to it.
Failure to do so may result in cut wires or short circuits that can lead to vehicle and
product damage.
3
■Precautions for Installation
●When installing this product, do not use any electro-taps
Using the electro-tap makes the electrical contact status unstable. This contact defect
may cause a malfunction in the product and damage this product and the vehicle.
Be sure to use the attached splice and dedicated tools such as cutting pliers for electric
work to install this product securely and properly.
●Insulate the metallic portion of the harness securely with electrical

tape.
●Caulking the plug
(1) Peel off the coating of (4) Caulk securely

the wires about 8 mm (2) Cover with a sleeve (3) Fold the wires
※Check if caulking has been performed securely by referring to the following figure
Caulk the conductors by these portions

Make the caulking thrust into the wire
Caulk the coating by these portions
●Caulking the splice
(1) Peel off the coating of the wires to (2) Peel off the wires to be (3) Entwine the wires (4) Caulk securely
be connected about 5 mm branched about 10 mm
※Insulate the caulked portion securely with a vinyl tape
4
●The ground conductor of this product has two branches (black and brown).
This has a very important significance to secure the voltage conversion accuracy.
Connect the ground conductor by referring to the following figure. Installing the
ground conductor in a different way from the connecting method specified by
APEXERA will give damage to this product and the mounted car engine.
Correct Connecting Method for the Ground Conductor

Connect the ground conductor to two positions of the same line.
Be sure to connect the brown wire to the ECU side.
Allow a space of 1 cm or more between the connecting point of the black wire
and the connecting point of the brown wire.
Vehicle harness
Engine
Control Unit（ＥＣＵ）
Brown wire (ground)

Black wire (ground)
Wrong Connecting Method for the Ground Conductor
Vehicle harness
Engine
Unite the ground

wires into a single Brown wire (ground)
line.
Black wire (ground)
Vehicle harness
Engine
Do not connect the

ground conductor
to any position Brown wire (ground)
(e.g. chassis ground) Black wire (ground)
other than the
specified position.
The above figure explains only the connection of the ground conductor. For the
other signal lines, refer to page 6 and page 7. Be sure to wire the power cable,
ground conductor and other signal lines to the positions specified by APEXERA.
5
■Installation
●Connecting the SAFC II
1.Remove the negative (ー) terminal of the battery

advice!
There is some setting data on car audio, car navigation, etc. that is backed up by the battery power
supply. We recommend you to take a note of the data in case it is lost.
！ CAUTION
●Before starting the wiring work, remove the negative terminal of the
battery.
Failure to do so way cause a short circuit and damage the wires. If the ECU connector
is removed while the battery is connected, the engine warning lamp may light up
continuously regardless of whether the SUPER AFC II is installed or not. At this time,
you must ask the distributor of the car model to perform maintenance and inspection.
●We shall not take any responsibility for damage to the vehicle or
related devices that may be caused by installation error.
2.Locate the Electronic Control Unit (hereafter referred to as ECU) of the vehicle by
referring to the vehicle specific wiring diagram.
3.Connect the harness attached to the SUPER AFC II securely to the power cable of the
vehicle harness, grounding wire, engine rpm signal wire, throttle signal wire, and
knocking signal wire from to the ECU by referring to the vehicle specific wiring diagram.
(Refer to page 8 and page 9.)
Connect the red wire to the power supply.

Connect the green wire to the engine rpm signal wire.
Connect the gray wire to the throttle signal wire.
Connect the black wire to the ground wire.
Connect brown wire to the ground wire.
Connect the purple wire to the knocking signal wire ・・・※
※For models with a single knocking wire.

Connect the purple wire directly to the knocking signal wire.
※For models with multiple knocking wires (knocking signal 1,

knocking signal 2, ・・・)
Refer to page 11 without making any connection at this time.
6
■Installation (cont.)
！ CAUTION
●Be sure to connect the black wire and the brown wire of the harness
attached to the SAFC II to the ground wire.
Failure to do so may cause this product not to function properly, thereby causing
damage to the product and the engine.
●When locating each wire, take special care not to cause a short
circuit.
An electrical fire may be caused or electrical devices may be damaged as a result.
●Securely install the splice without any loose contacts.

Electric devices may be damaged as a result.
4.Cut the airflow signal wire or pressure signal wire of the vehicle harness and install a
plug by referring to the vehicle specific wiring diagram.
Plug ：ECU side

Plug receptacle ：Airflow sensor or pressure sensor side
Vehicles equipped with the RB26DETT have 2 airflow signal wires.

Cut these 2 wires.
5.Connect the harness attached to the SAFC II to the plug installed in step 4
For Hot Wire/ Plug receptacle: White wire

Flap/Pressure Plug: Yellow wire
sensor
Plug receptacle: Orange wire

For Karman
Plug: Pink wire
6.Insulate the splice and unused plug with electrical tape.
7.Reconnect the negative (ー) terminal of the battery.
7
●Wire connecting method
※For vehicles using a hot wire/flap/pressure sensor
Vehicle harness
！ CAUTION
●Be sure to connect the brown wire to the ECU side.
Failure to do so may cause this product to function improperly, thereby causing damage
to the product and the engine
※For vehicles equipped with the RB26DETT
Vehicle harness
Red wire (power supply)

Green wire (rpm signal)
Purple wire (knocking signal)
Gray wire (throttle signal)
Brown wire (ground)
Black wire (ground)
Harness for branching
Yellow wire (airflow/pressure signal output)

White wire (airflow/pressure signal input 1)
Blue wire (airflow/pressure signal input 2)
！ CAUTION
●Be sure to connect the brown wire to the ECU side from the black wire
to the product and the engine.
8
※For vehicles using the Karman type frequency sensor
Vehicle harness
ECU
Red wire (power supply)

Green wire (rpm signal)
Purple wire (knocking signal)
Gray wire (throttle signal)
Brown wire (ground)
Black wire (ground)
Pink wire (airflow signal output)
Orange wire (airflow signal input)
！ CAUTION
●Be sure to connect the brown wire to the ECU side from the black wire
to the product and the engine.
！ WARNING
●Mount the SAFC II so that it does not interfere with driving.
Normal driving operations may be prevented, resulting in an accident.
●Do not install the SAFC II in a high-temperature place or in a location

where it may come in contact with water.
An electric shock/fire may be caused. This may cause damage to the product and
vehicle.
●When routing the connecting harness of the SAFC II, route the harness
away from moving parts.
The connecting harness may be cut or short-circuited.
The SAFC II will be damaged, thereby causing damage to the vehicle and other electric
parts.
9
●Check points after installation.
After installing the SUPER AFC II, check the following items once again
・Check if the harness attached to the SAFC II is securely connected
・Check if the harness is not routed improperly
・Check if the SAFC II is securely mounted
・Check if the negative (ー) terminal of the battery is securely connected
●Turn on the ignition switch. (Do not start the engine.)

Check the following contents after turning on the ignition switch
・Check if the characters are correctly displayed on the display screen of the SAFC II
If the display of this product is not correct, discontinue use of the product
immediately and contact the distributor.
・Check for any abnormal noise or abnormal smell from the SAFC II and the vehicle.
If any abnormal noise or abnormal smell is sensed, discontinue use of this product
immediately and contact the distributor.
●Initial setup
・If no abnormality is found with the ignition switch ON, perform initial setup for the
SAFC II.
Perform sensor type and sensor number setting, number-of-cylinders setting, throttle
sensor voltage check, throttle sensor type setting, throttle learning, and knocking signal
correction according to “Initial Setup” on page 13 in the separate Instruction Manual.
・When the engine is ready to start after initial setup, the installation work is completed.
！ CAUTION
●Do not start the engine under any circumstance before the initial
setup is performed
If the engine is started before initial setup, the engine may be damaged. Set the
corresponding items by referring to page 13 in the Chapter pertaining to “Initial Setup”
in the separate Instruction Manual.
！ WARNING
●If the engine check lamp illuminates, you must contact a dealer for
inspection. If the vehicle is driven at a high speed with the engine
warning lamp ON, the engine may be damaged, leading to an
unexpected accident. Do not drive the vehicle under these conditions.
10
※For vehicles equipped with multiple knocking signal wires
Connect only the power wire, ground wire, engine rpm signal wire, and throttle signal wire
and proceed to the following operations.
For connecting the knocking signal wire, perform this work separately according to the
following procedure
Connect the power wire, ground wire, engine rpm signal wire, and throttle signal wire
Page 6 in this document
Connect the airflow or pressure signal wire

Make checks after completion of installation

With the ignition switch ON

●Check the display screen of the SAFC II
●Check for any abnormal noise or abnormal smell from the SAFC II and the vehicle
Perform sensor type and sensor number setting, number-of-cylinders setting, throttle
sensor voltage checking, throttle sensor type setting, and throttle learning according to
“Initial Setup” on page 13 in the separate Instruction Manual
After the initial setup (except knocking signal correction) is completed and the engine is
ready to start, check the sensor output value of each knocking sensor signal by referring
to the sensor check items on page 52 in the Chapter pertaining to “etc. Mode”. Perform
wiring to the sensor signal wire with the highest output value. If there is only a small
difference among output values, increase the rpm speed from idling to 2000 rpm. Make a
comparison under this condition. If there is no difference, make a connection to knocking
signal 1.
11
■ECU Arrangement Diagram
●Perform installation by referring to the symbols in the
corresponding columns of the tables of applicable models on
and after page 14
P
L
D
B
F
E C A
N
M
A : Lower part of the passenger seat dash side

B : Right side of the glove box
C : Foot position of the passenger seat
D : Inner part of the glove box
E : Inner part of the center console
I F : Under the driver’s seat
G : Under the passenger seat
H H : Near the steering column
I : Left side of the meter panel
J : Lower part of the driver’s seat dash side
J K : Left side of the center console
K L : Engine room
M : Before the rear trunk
N : Behind after the driver’s seat
O : Behind the passenger seat
P : Upper inner part of the center console
12
■How to Refer to the ECU Terminal
Arrangement Diagram
This ECU terminal arrangement diagram is viewed from the

direction of the arrow.
The direction of the ECU varies depending upon the vehicle.

Perform the installation work after confirming the connector
shape and the number of pins.
！ WARNING
●If any abnormal noise or abnormal smell is sensed during the
installation work of this product, stop the work immediately and
contact the distributor or your nearest APEXERA business office
Continuing the installation under such conditions may cause an electric shock or fire
causing damage to electric devices.
13
■Table of Applicable Models (TOYOTA)
Explanation of sensor type indication
HW-HotWire FL-Flap
Example PR-3 PR-Pressure KR-Karman
Sensor type Sensor number
Manufacturing ECU Terminal Sensor

Car Name Car Model Engine Model Remarks
year Position Drawing Type
’97.7∼‘00.7 L T10-e HW-13

UCF2#
‘94.10∼‘97.6 HW-12
CELCIOR 1UZ-FE T8-a
‘92.9∼‘94.9 D
UCF1# KR
‘89.10∼‘92.8 T5-f
CROWN ‘99.9∼‘01.7
JZS173 1JZ-GE L T10-a PR-16
ROYAL
JZS171 1JZ-GTE T10-b HW-23

CROWN ‘99.9∼‘01.7 L
ATHLETE ＪZS173 1JZ-GE T10-a PR-16
CROWN ‘91.10∼‘95.7
UZS141 1UZ-FE D T7-b KR
MAJESTA
JZS171W 1JZ-GTE T10-b HW-23

CROWN ‘99.9∼‘01.7 L
ESTATE
JZS173W 1JZ-GE T10-a PR-16
CROWN JZS14# 2JZ-GE ‘91.10∼‘95.7 D T8-b PR-3
JZS161 2JZ-GTE ‘97.8∼※

L T10-c HW-13
JZS160 2JZ-GE ‘97.8∼‘00.6
ARISTO 2JZ-GTE PR-1

JZS147 ‘91.10∼‘97.7 T7-c
2JZ-GE C PR-3
UZS143 1UZ-FE ‘92.10∼‘97.7 T7-b KR
UZZ40 3UZ-FE ‘01.4∼※ L T11-b HW-25
‘96.8∼‘01.3 T8-d HW-12

JZZ30 1JZ-GTE
‘91.5∼‘96.7 T8-c PR-1
JZZ31 2JZ-GE ‘94.1∼‘96.7 C T8-b PR-3
‘94.1∼‘95.4 T8-a
SOARER UZZ31 1UZ-FE
‘91.5∼‘93.12 T7-a
KR
‘89.1∼‘91.4 T5-a
MZ20 7M-GTE
‘86.1∼‘88.12 T2-b
D
‘89.1∼‘91.4 T5-a
GZ20 1G-GTE FL-1
‘86.1∼‘88.12 T2-e
14
‘89.1∼‘91.4 T5-b
SOARER GZ20 1G-GE D PR-3
‘86.1∼‘88.12 T2-d
‘97.8∼‘02.8 T10-c HW-13

2JZ-GTE
JZA80 C PR-1
‘93.5∼‘97.7 T7-c
2JZ-GE PR-3
JZA70 1JZ-GTE ‘90.8∼‘93.4 T6-a PR-1
‘88.9∼‘90.7 Ｔ５-ａ
KR
SUPRA MA70 7M-GTE ‘86.2∼‘88.8 T2-b
‘88.8 Turbo A PR-1

D T5-a
‘88.9∼‘93.4
1G-GTE FL-1
‘86.2∼‘88.8 T2-e
GA70
‘88.9∼‘93.4 T5-b
1G-GE PR-3
‘86.2∼‘88.8 T2-d
JZX110 1JZ-GTE ‘00.10 T10-b HW-23

MARK II ∼‘04.10 L
JZX115 1JZ-GE T10-a PR-16
JZX110W 1JZ-GTE T10-b HW-23

MARK II ‘02.1∼※ L
BLID
JZX115W 1JZ-GE T10-a PR-16
‘99.8∼‘02.1 T10-f
MCV20W 1MZ-FE
MARK II ‘97.5∼‘99.7
E HW-13
QUALIS
T8-f
MCV25W ‘97.5∼‘02.1
2MZ-FE
MCV21W
VEROSSA JZX110 1JZ-GTE ‘01.8∼‘04.4 L T10-b HW-23
MARK II
JZX100 ‘96.9∼‘01.7 T8-d HW-12
‘96.9∼‘00.9
1JZ-GTE
‘94.9∼‘96.8 T8-e
PR-1
JZX90 ‘92.10∼‘94.8 T8-c
E
1JZ-GE ‘92.10∼‘96.8 T6-a
MARK II
‘94.9∼‘96.8 T8-d PR-3
CRESTA
CHASER JZX91 2JZ-GE
‘92.10∼‘94.8 T8-b
1JZ-GTE PR-1
JZX81 ‘90.8∼‘92.9 T6-a
1JZ-GE PR-3
D
1G-GTE ‘88.8∼‘90.7 T5-a FL-1
GX81
1G-GE ‘88.8∼‘92.9 T5-b PR-3
15
‘93.10∼‘99.10 PR-2
T5-c
3S-GTE ‘91.12∼‘93.9
FL-2
‘89.10∼‘91.11 T5-b
SW20 ‘97.12∼‘99.10 T9-b HW-13
MR2 ‘93.10∼‘97.11 M T6-b

3S-GE
‘91.12∼‘93.9 T5-c PR-3
‘89.10∼‘91.11 T5-b
4A-GZE ‘86.8∼‘89.9 T2-a FL-3

AW11
4A-GE ‘84.6∼‘89.9 T1-a PR-3
ZZT230 1ZZ-FE
‘99.9∼※ ＬＴ９−ｂ HW-24
ZZT231 2ZZ-GE
ST205 3S-GTE ‘94.2∼‘99.8 T5-c PR-2
3S-GE ‘93.10∼‘97.11 T6-b
M/T T4-f
‘96.6∼‘99.8
ST203 A/T T5-g
PR-3
ST202 M/T T4-a
3S-FE
CELICA ‘95.8∼‘96.5
A/T
E
‘93.10∼‘95.7 T5-c
‘91.9∼‘93.9
ST185 3S-GTE FL-2
‘89.10∼‘91.8 T5-b
ST182 3S-GE ‘89.10∼‘93.9 T5-c PR-3
ST165 3S-GTE T2-a

‘85.8∼‘89.9 FL-2
ST162 3S-GE T2-c
ST206 3S-GE ‘94.1∼‘98.7 T6-b
M/T T4-f
‘96.6∼‘98.7
A/T T5-g
M/T T4-a
CURREN E PR-3
ST207 ‘95.10∼‘96.5
3S-FE With A/T TRC T6-b
ST206
Without A/T TRC T5-c
With TRC T6-b

‘94.1∼‘95.9
Without TRC T5-c
16
3S-GE ‘93.10∼‘98.12 T6-b
M/T T4-f
‘96.6∼‘98.12
A/T T5-g
CARINA ED ST203 M/T T4-a

E PR-3
CORONA EXIV ST202 ‘95.8∼‘96.5
3S-FE With A/T TRC T6-b
Without A/T TRC T5-c
With TRC T6-b

‘93.10∼‘95.7
Without TRC T5-c
ST246W 3S-GTE PR-2

‘02.9∼※ T12-a
ZZT241W 1ZZ-FE HW-24
ST215W 3S-GTE T9-a PR-2

‘97.8∼‘02.8
ST215G
3S-FE T5-d
ST210G
ST195G 3S-GE ‘95.2∼‘97.7 T6-b
M/T T4-f
‘96.1∼‘97.7 2WD A/T T5-e
4WD A/T T5-g

CALDINA D
FF With TRC T6-b
ST195G FF Without TRC T5-c PR-3

3S-FE ‘94.2∼‘95.12
ST191G 4WD M/T T4-a
4WD A/T T5-c
FF A/T T6-c
‘92.11∼‘94.1 4WD M/T T4-a
4WD A/T T5-c
M/T T4-e
ST190G 4S-FE ‘92.11∼‘95.12
A/T T5-c
M/T T4-b
4A-GE FL-4
A/T T5-b
AE101 ‘92.5∼‘95.4
M/T T4-b
CAROLLA FX 4A-FE E
A/T T5-c
PR-3
‘89.5∼‘92.4 T4-b
AE92 4A-GE
‘87.5∼‘89.4 T1-a
17
4A-GE ‘97.4∼‘00.9 T5-b

AE111
4A-FE ‘95.5∼‘97.3 PR-3
AE110 5A-FE ‘95.5∼‘00.9 T4-b
M/T
CAROLLA 4A-GE FL-4
E A/T T5-b
SPRINTER ‘91.6∼‘95.4
AE101
M/T T4-b
4A-FE
A/T T5-c
PR-3
‘89.5∼‘91.5 T4-b
AE92 4A-GE
‘87.5∼‘89.4 T1-a
4A-GE T5-b
AE111
4A-FE ‘95.5∼‘00.9 PR-3
T4-b
AE110 5A-FE
4A-GZE T5-b PR-1
M/T T4-b
4A-GE FL-4
AE101 ‘91.6∼‘95.4 A/T T5-b
E
LEVIN M/T T4-b
TRUENO 4A-FE PR-3
A/T T5-c
‘89.5∼‘91.5 T5-b PR-1

4A-GZE
‘87.5∼‘89.4 T2-a FL-3
AE92
‘89.5∼‘91.5 T4-a
4A-GE
‘87.5∼‘89.4 T1-a PR-3
AE86 4A-GEU ‘83.5∼‘87.4 A T1-c
M/T T4-b
4A-GE FL-4
CERES A/T T5-b
AE101 ‘92.5∼‘95.4 E
MARINO M/T T4-b
4A-FE PR-3
A/T T5-c
M/T T9-c
ALTEZZA SXE10 3S-GE ‘98.10∼※ L HW-15
A/T T10-d
ALTEZZA JCE15W ‘01.7∼※

2JZ-GE L T10-b HW-24
GITA JCE10W
‘99.10∼※ Including
MR-S ZZW30 1ZZ-FE D T9-b HW-24
Sequential M/T
OPA ZCT1# 1ZZ-FE ‘00.8∼‘02.5 D T9-b HW-24
18
M/T T4-d
4E-FTE ‘96.1∼‘99.7 PR-1
EP91 D A/T T4-c
4E-FE ‘96.1∼‘97.12 T3-b PR-3
‘89.12∼‘95.12 M/T T3-a

STARLET 4E-FTE ‘92.1∼‘95.12 T4-b PR-1
EP82 A/T
‘89.12∼‘91.12 T3-a
E
4E-FE ‘89.12∼‘95.12 T3-c PR-3
2E-TE ‘86.1∼‘89.11
EP71 T1-b PR-1
2E-E
ZCA26W ‘00.5∼※
1ZZ-FE D T9-b HW-24
ZCA25W
M/T T4-f
SXA1#G 3S-FE
‘97.9∼‘00.4 A/T T5-g
SXA11W
RAV4 3S-GE T5-c
SXA10W ‘96.8∼‘00.4
E PR-3
M/T T4-a
SXA11G ‘95.4∼‘97.8
A/T T5-c
3S-FE
M/T T4-a
SXA10G ‘94.5∼‘97.8
A/T T5-c
‘02.12∼※ T12-a
NCP13 1NZ-FE
‘00.10∼‘02.11 T6-d
‘02.12∼※ T12-a
VITZ NCP10 D HW-24
‘00.10∼‘02.11 T6-d
2NZ-FE
‘02.12∼※ T12-a
NCP15
‘00.10∼‘02.11 T6-d
NCP25
1NZ-FE
NCP21
T6-d
NCP20 2NZ-FE
FANCARGO ‘99.8∼※ P HW-24
NCP25
1NZ-FE With
NCP21 T9-d
Steermatic
NCP20 2NZ-FE
NCP61 1NZ-FE
ist ‘02.5∼※ D T12-a HW-24
NCP60 2NZ-FE
19
ZZE12# 1ZZ-FE
‘02.9∼※ T12-a
NZE124
1NZ-FE
NZE121
CAROLLA D HW-24
ZZE12# 1ZZ-FE T9-b
‘00.8∼‘02.8
NZE124
1NZ-FE T6-d
NZE121
ZZE123G 2ZZ-GE T10-g
M/T T9-b
ZZE122G 1ZZ-FE ‘02.9∼※
A/T
NZE124G T12-a
CAROLLA 1NZ-FE
NZE121G D HW-24
FIELDER
ZZE123G 2ZZ-GE T10-g
ZZE122G 1ZZ-FE ‘00.8∼‘02.8 T9-b
NZE124G
1NZ-FE T6-d
NZE121G
ZZE123 2ZZ-GE T10-g
ZZE124
1ZZ-FE ‘02.9∼※
ZZE122
CAROLLA T12-a
NZE124
RUNX 1NZ-FE D HW-24
NZE121
ALEX
ZZE123 2ZZ-GE T10-g
‘01.1∼‘02.8
NZE124
1NZ-FE T6-d
NZE121
ZZE124N ‘01.7∼※
1ZZ-FE T9-b
CAROLLA
ZZE122N D HW-24
SPACIO ‘01.5∼※
NZE121N 1NZ-FE T6-d
ZZE128 2ZZ-GE T10-g

WILL VS ‘01.4∼※ D HW-24
ZZE129
1ZZ-FE T9-b
ZZE127
NCP75 1NZ-FE
WILL ‘02.10∼※ D T12-a HW-24
CYPHA
NCP70 2NZ-FE
ZZT240 1ZZ-FE
ALLION ‘01.12∼※ B T12-a HW-24
NZT240 1NZ-FE
WISH ZNE1#G 1ZZ-FE ‘03.1∼※ D T12-a HW-24
20
NCP12 1NZ-FE
NCP16 2NZ-FE ‘02.8∼※ T12-a
SCP11 1SZ-FE
PLATZ E HW-24
NCP12 1NZ-FE
NCP16 2NZ-FE ‘99.8∼‘02.7 T6-d
SCP11 1SZ-FE
NCP30 2NZ-FE
‘02.8∼※
NCP35
T12-a
NCP31
1NZ-FE
NCP34 ‘02.8∼‘03.3
bB D HW-24
NCP30 2NZ-FE
‘00.2∼‘02.7
NCP35
T6-d
NCP31
1NZ-FE
NCP34 ‘01.6∼‘02.7
WINDOM MCV30 1MZ-FE ‘01.8∼※ B T11-a HW-13
ESTIMA MCR#0W 1MZ-FE ‘00.1∼※ D T10-f HW-15
ALPHARD MNH1#W 1MZ-FE ‘02.5∼※ D T10-f HW-15
ZZE137 2ZZ-GE
VOLTZ ‘02.8∼※ D T12-a HW-24
ZZE138
1ZZ-FE
ZZE136
SIENTA NCP81G 1NZ-FE ‘03.9∼※ B T11-c HW-24
PASSO KGC10 1KR-FE ‘04.6∼※ D T13-a PR-20
1NZ-FE ‘04.7∼※
PORTE NNP1# D T12-a HW-24
2NZ-FE
21
■ECU Terminal Arrangement Table (TOYOTA)
rpm 1 rpm 1
Pressure signal rpm 2 Pressure signal
rpm 2 Ground Throttle signal IG power Ground Knocking signal IG power

※Without knocking signal ※Without throttle signal
rpm 1 Airflow signal

rpm 1
Pressure signal
rpm 2 Ground IG power rpm 2 Ground Throttle signal IG power

Knocking signal
※Without knocking signal and throttle signal

rpm 1
Ground Throttle signal Knocking signal 2 IG power

rpm 2 Ground Throttle signal IG power
Knocking signal 1
※Without knocking signal
rpm 1 rpm 1 Airflow signal

rpm 2
Ground Pressure signal Knocking signal 1

Throttle signal IG power rpm 2 Ground IG power
Knocking signal 2
※Without knocking signal ※Without throttle signal
rpm 1 Pressure signal

rpm 1 Pressure signal
rpm 2 Ground Knocking signal Throttle signal IG power

Ground Knocking signal IG power
rpm 2
※Without throttle signal
Ordinary connection : rpm 1

Multiple connection : rpm 2
22
rpm 1 Pressure signal rpm 1 Knocking signal pressure signal
Ground rpm 2
Ground rpm 2 IG power Throttle signal IG power

/pressure signal Pressure signal
rpm 1
Ground rpm 2 Throttle signal IG power Ground rpm 2 Throttle signal IG power
Knocking signal
Knocking signal
rpm 1 Knocking signal Pressure signal

Pressure signal rpm 1
Ground Knocking signal Ground rpm 2 IG power

IG power
※Without throttle signal ※Without throttle signal
rpm 1 Knocking signal Pressure signal rpm 1 Knocking signal 1 Airflow signal
rpm 2 rpm 2 Ground IG power

Ground Throttle signal IG power
Knocking signal 2
Turbo A pressure signal
Throttle signal
Airflow signal
Knocking signal /pressure signal
rpm 1 rpm 1 Airflow signal/pressure signal
rpm 2 Ground IG power rpm 2 Ground

Throttle signal Throttle signal IG power
Knocking signal

23
rpm 1 Pressure signal rpm 1 Knocking signal Pressure signal
rpm 2 Ground Throttle signal IG power rpm 2

Ground Throttle signal IG power
Knocking signal
Knocking signal 1 Airflow signal IG power

rpm 2
Knocking signal 2 rpm 1 Ground Throttle signal
rpm 2 Knocking signal 1 Pressure signal

rpm 1 Knocking signal Pressure signal
Ground rpm 1 IG power

Throttle signal
Ground rpm 2 Throttle signal IG power Knocking signal 2
Knocking signal
rpm 2 Knocking signal Pressure signal rpm 1 Pressure signal
Ground rpm 1 Throttle signal IG power Ground rpm 2 Throttle signal IG power
Knocking signal Airflow signal
Ground Throttle signal rpm IG power
Ordinary connection : rpm1

24
25
Knocking signal Airflow signal
Airflow signal
Knocking signal Ground rpm IG power Throttle signal Ground rpm IG power
Throttle signal
Ground Throttle signal Knocking signal 1 Pressure signal
Knocking signal rpm IG power

Airflow signal Knocking signal 2 Throttle signal Ground rpm IG power
Knocking
Knocking signal 1 Airflow signal Knocking signal 1 signal 2 Airflow signal
Knocking signal 2 Throttle signal Ground rpm IG power rpm Throttle Ground IG power
signal
Knocking signal Knocking

Airflow signal Knocking signal 2 Airflow signal
signal 1
Throttle signal Ground rpm IG power Ground IG power

rpm Throttle
signal
Knocking signal 1 Airflow signal Knocking signal Airflow signal
Knocking signal 2 Ground rpm IG power Throttle signal Ground rpm IG power
Throttle signal
26
Knocking signal 1 Knocking signal 2 Ground rpm IG power
Airflow signal
Throttle signal
Ground Knocking signal 2 Knocking signal 1 rpm IG power
Airflow signal
Throttle signal
Knocking signal Ground rpm IG power
Throttle signal Airflow signal
Ground Knocking signal rpm IG power
Throttle signal Airflow signal/pressure signal
IG power Pressure signal

Ground
※Set the number of cylinders

“1” at intial setting.〔etc.→ Car
sel.→Cｙｌ 1〕 rpm
Knocking signal
Throttle signal
27
■Table of Applicable Models (NISSAN)
HW-HotWire FL-Flap

PRESIDENT G50 VH45DE ‘90.10∼‘02.12 A N4-d HW-1
INFINITY Q45 G50 VH45DE ‘89.11∼‘97.9 A N4-d HW-1
CIMA HF50 VQ30DET ‘01.1∼※ D N8-c HW-17
FGY33 VH41DE N9-a HW-1

‘98.9∼‘00.12
FHY33 VQ30DET N5-a HW-4
CIMA Ⅲ A
FGY33 VH41DE N6-a HW-1
‘96.6∼‘98.8
FHY33 VQ30DET N5-a HW-4
FGY32 VH41DE ‘91.8∼‘96.5 N4-d HW-1

CIMA Ⅱ A
FPY32 VG30DET ‘93.9∼‘96.5 N4-e HW-4
‘89.8∼‘91.7 N4-i
CIMA Ⅰ VG30DET
FPY31 A HW-4
VG30DE ‘88.1∼‘89.7 N2-a
Except
Roadster
Z33 VQ35DE ‘02.7∼※ D /35thAnnive N10-d HW-26
FAIRLADY Z rsaryModel
/TypeE
VG30DETT ‘89.7∼‘00.8
Z32 C N4-a HW-2
VG30DE
VQ25DE ‘97.10∼‘99.6
Y33 N5-a
VQ30DET ‘96.3∼‘99.6
VQ30DE
LEOPARD A HW-4
VG30DET
UF31 N4-g
VG30DE ‘88.8∼‘92.5
GF31 VG20DET N2-a
JGBY32 VH41DE N4-d HW-1

LEOPARD ‘92.6∼‘96.2 A
J FERIE
JPY32 VG30DE N4-h HW-4
Y34 ‘99.6∼‘04.10 D N8-c HW-18

VQ30DET
CEDRIC Y33 ‘95.6∼‘99.5 N5-a

GLORIA VQ30DE A HW-4
VG30DET ‘91.6∼‘95.5
Y32 N4-h
VG30DE
28
CEDRIC VG20DET ‘89.6∼‘91.5

Y31 A N4-f HW-4
GLORIA VG20E
‘01.1∼‘03.2 N8-a
A33 VQ20DE HW-17
‘98.12∼‘00.12 N8-b
VQ30DE
N6-c
VQ25DE
‘97.1∼‘98.11 E
M/T N4-a
VQ20DE
A32 A/T N6-c
CEFIRO
VQ30DE
VQ25DE ‘94.8∼‘96.12 N4-b HW-4
VQ20DE
RB20DET ‘88.9∼‘94.7 N4-j
A31 RB25DE ‘92.5∼‘94.7 A N4-b
RB20DE ‘88.9∼‘94.7 N4-j
VQ25DE ‘97.1∼‘00.8
CEFIRO VQ20DE
W#A32 E N6-c HW-4
WAGON
VQ30DE ‘97.1∼‘99.7
RB25DET
C35 RB25DE ‘97.6∼‘02.12 N6-b
RB20DE
RB25DET ‘94.1∼‘97.5
LAUREL A HW-4
C34
RB25DE ‘93.1∼‘97.5
RB20DE N4-d
RB20DET ‘89.1∼‘92.12
C33
RB20DE
‘03.2∼※ N10-d
V35 VQ35DE D HW-26
‘02.2∼※ N8-c
RB26DETT ‘99.1∼‘02.8 N4-c HW-3

R34
RB25DET ‘98.5∼‘01.5 N6-b HW-4
RB26DETT ‘95.1∼‘98.12 N4-c HW-3

SKYLINE
R33
RB25DET ‘93.8∼‘98.4
A N4-d HW-4
RB25DE
RB26DETT ‘89.8∼‘94.12 N4-c HW-3
RB25DE ‘91.8∼‘93.7
R32
N4-d HW-4
RB20DET ‘89.5∼‘93.7
RB20DE
29
RB20ET ‘87.8∼‘89.4
SKYLINE R31 A N1-a HW-4
RB20E
NM35 VQ25DET ‘01.10∼※ D N8-c HW-18

STEGEA
RB25DET ‘96.8∼‘01.9
W#C34 A N6-b HW-4
RB25DE
STEGEA
AUTECH WGNC34 RB26DETT ‘97.10∼‘01.9 A N4-c HW-3
Ver.260RS
2WD N8-e
QG18DE
BLUEBIRD ‘00.8∼※ 4WD
G10 L HW-18
SYLPHY N7-a
QG15DE
SR20VE ‘97.9∼‘00.7 HW-14
SR20DE ‘96.1∼‘00.7
U14
‘96.1∼‘98.8 Except the

SR18DE
Lean Burn
N3-a
BLUEBIRD SR20DET E HW-6
U13 SR20DE ‘91.9∼‘95.12
SR18DE
SR20DET ‘89.10∼‘91.8
SR20DE
U12
CA18DET ‘87.9∼‘89.9 N4-a HW-7
CA18DE
S15 ‘99.1∼‘02.7
N3-a
SR20DET ‘96.6∼‘98.12 HW-5
S14 ‘93.10∼‘96.5 N4-a
SR20DE ‘93.10∼‘98.12 N3-a

SILVIA A
SR20DET N3-b HW-6
PS13 ‘91.1∼‘93.9
SR20DE N3-a
CA18DET ‘88.5∼‘90.12
S13 N4-a HW-7
CA18DE
SR20DET ‘96.8∼‘98.12 N3-a

SR20DE
RPS13 HW-6
180SX SR20DET ‘91.1∼‘96.7 A N3-b
RS13 CA18DET ‘89.3∼‘90.12 N4-a HW-7
30
‘97.9∼‘00.8 Except the

SR16VE HW-6
N1 Specification
N15
SR18DE ‘95.1∼‘00.8 HW-14
PULSER E N3-a
SR20DET HW-5
N14 ‘90.8∼‘94.12
SR18DE HW-6
‘02.5∼※ N10-c
QR20DE HW-18
P12 ‘01.1∼‘02.4 D
N8-d
‘01.8∼‘03.6 HW-21
SR20VE
‘97.9∼‘00.12 HW-14
PRIMERA
P11 SR20DE ‘95.9∼‘00.12
SR18DE ‘95.9∼‘98.8 E N3-a

HW-6
SR20DE ‘90.2∼‘95.8
P10
SR18DE ‘92.9∼‘95.8
‘02.5∼※ N10-c
QR20DE HW-18
W#P12 ‘01.1∼‘02.4 D
N8-d
‘01.8∼‘03.6 HW-21
PRIMERA
SR20VE
WAGON
HW-14
‘97.9∼‘00.12
W#P11 SR20DE E N3-a
HW-6
SR18DE ‘97.9∼‘99.3
SR20DET HW-5
W11 ‘98.8∼‘00.4
SR20DE HW-6
AVENIR SR20DET ‘95.8∼‘98.7 E N3-a HW-5
W10 SR20DE ‘90.5∼‘98.7

HW-6
SR18DE ‘93.1∼‘98.7
B14 ‘94.1∼‘98.9
SUNNY SR18DE E N3-a HW-6
B13 ‘90.1∼‘93.12
NX COUPE B13 SR18DE ‘90.1∼‘93.12 E N3-a HW-6
CR14DE
‘02.3∼※
K12 CR12DE L Except the M/T N10-b PR-11
CR10DE ‘02.3∼‘04.4
MARCH
Including
CG13DE
‘92.1∼‘02.2 CGA3DE
K11 E N3-c HW-9
CG10DE
31
Z11 CR14DE ‘02.10∼※ L N10-b PR-11

CUBE
‘98.2∼‘02.9 Including
Z10 CG13DE C N3-c HW-9
CGA3DE
TERRANO YD21 VG30E ‘89.10∼‘95.8 F N3-a HW-6
QR20DE ‘00.11∼※ HW-18

X-TRAIL T30 B N8-d
SR20VET ‘01.2∼※ HW-19
WINGROAD Y11 QR20DE ‘01.10∼※ E N8-d HW-18
E51 ‘02.5∼※ L N10-a HW-18

VQ35DE
APE50 ‘00.8∼‘02.5
ELGRAND N8-a HW-1
APWE50
E
ALE50 ‘97.5∼‘00.8
VG33E N4-a HW-6
ALWE50
TC24 ‘01.12∼※
SERENA QR20DE E N8-d HW-5
TNA24
BASSARA JHU30 VQ30DE ‘01.8∼‘03.6 E N8-a HW-18
NA N11-b PR-13
MOCO MG21S K6A ‘02.4∼※ L
T/C N11-a PR-8
32
■ECU Terminal Arrangement Table (NISSAN)
Knocking signal 5 rpm

Knocking signal 4 Knocking signal 1 Ground
rpm IG power Ground
Airflow signal Knocking Knocking Knocking signal 3 IG power

Knocking signal signal 6 signal 2
Airflow signal
※Without throttle signal ※Knocking signal 2 to 6 : For FPY31 only
rpm Airflow signal rpm Airflow signal

Ground Ground
Knocking signal Knocking signal

Throttle signal IG power IG power
Throttle signal
rpm Airflow signal Ground rpm Knocking signal

Airflow signal
Knocking signal (99/11∼) IG power Ground

IG power
Throttle signal Throttle signal
Knocking signal 2
rpm Knocking signal 1
Knocking signal 1
rpm Airflow signal 1
Airflow signal
Knocking signal 2 IG power Ground Throttle signal Ground

Throttle signal Airflow signal 2 IG power

rpm Airflow signal Ground
Airflow signal
Throttle signal Knocking signal Throttle signal IG power

Knocking signal 1 Ground
IG power
33
rpm Knocking signal 1 ・ 2 ・ 3
Airflow signal Ground rpm Airflow signal Ground
Knocking signal IG power IG power

Knocking signal 4 ・ 5 ・ 6
Throttle signal
rpm
Knocking signal 1 ・ 2 ・ 3 Airflow signal Ground
Knocking signal 1 ・ 2 ・ 3 IG power

Knocking signal 4 ・ 5 ・ 6 IG power
Knocking signal 4 ・ 5 ・ 6
Throttle signal
Knocking signal
Knocking signal 1 Knocking signal 2 rpm
Throttle signal IG power
IG power
Throttle signal Ground Airflow signal
IG power
Throttle signal Knocking signal 1 IG power rpm Throttle signal Ground
rpm Knocking signal 2 Airflow signal Knocking

signal 2
Knocking signal 1
Ground Airflow signal
Throttle signal Ground IG power

rpm
Knocking signal
Airflow signal
34
Airflow signal IG power
Knocking rpm Ground Knocking

rpm Ground Throttle signal
signal signal
Airflow signal
Throttle signal
Airflow signal IG power Knocking signal Airflow signal IG power
rpm Ground rpm Throttle signal

Ground
Knocking signal
Throttle signal IG power Airflow signal IG power

Ground
rpm Airflow signal Knocking signal rpm Ground Knocking

signal Throttle signal
rpm
Ground IG power
Knocking signal Throttle signal IG power
rpm Airflow signal Knocking signal 2

Airflow signal Ground
Throttle signal Knocking
signal 1
rpm
Knocking signal Knocking signal rpm IG power

Pressure signal Ground Throttle signal
35
IG power
Knocking signal Throttle signal
Airflow signal
※Set the number of cylinders “1” at intial Ground
rpm
setting.〔etc.→Car sel.→Cｙｌ 1〕
Pressure signal
Knocking signal rpm IG power Knocking signal
rpm IG power
Throttle signal Pressure signal Throttle signal

Ground Ground
36
■Table of Applicable Models (HONDA)
HW-HotWire FL-Flap

NA2 C32B ‘97.2∼※

H2-f
NSX ‘95.3∼※ N
NA1 C30A
‘90.9∼‘95.2 H2-a
KA9 C35A ‘96.2∼‘04.9

LEGEND C H2-a
KA8 ‘90.10∼‘96.1
C32A
KA7
UA5 J32A
‘98.10∼‘03.5 E H7-b
UA4 J25A
UA2 G25A
INSPIRE ‘95.2∼‘98.9 H2-c
UA1 G20A
C
CC2 G25A ‘92.1∼‘95.1 H2-d
CB5 G20A ‘89.10∼‘91.12 H2-b
BB8 ‘96.12∼‘00.9 H6-a

BB6
PRELUDE H22A C PR-6
BB1 With TRC H2-e
‘91.9∼‘96.11
BB4 Without TRC H3-b
CL7 K20A ‘02.12∼※ H12-a

ACCORD
E
EURO R ‘00.6∼‘02.9
CL1 H22A H8-a
CL9 K24A
‘02.10∼※ H11-b
CL8
K20A
CL7
A/T H7-c
CL3 F20B ‘00.6∼‘02.9
E
M/T H8-a
ACCORD CF3 F18B H7-a
‘97.9∼‘00.5 A/T H7-c
CF4 F20B
M/T H8-a
CD5 F22B H3-a

‘93.9∼‘97.8 C
CD6 H22A H3-b
37
CM3 ‘02.11∼※
K24A H11-b
CM2
A/T H7-c
CH9 ‘99.1∼‘02.10
M/T H8-a
H23A E
A/T H7-c
ACCORD CL2 ‘00.6∼‘02.10
WAGON M/T H8-a
CF7 ‘97.10∼‘02.10
F23A H7-a
CF6
CE1 F22B ‘94.3∼‘97.9

C H3-a
CB9 F22A ‘91.3∼‘94.2
TORNEO ‘00.6∼‘02.9
CL1 H22A E H8-a
EURO R
A/T H7-c
CL3 F20B ‘00.6∼‘02.9
M/T H8-a
TORNEO CF3 F18B E H7-a

‘97.9∼‘00.5 A/T H7-c
CF4 F20B
M/T H8-a PR-6
S2000 AP1 F20C ‘99.4∼※ A H8-b
DC5 K20A ‘01.7∼※ D H9-a
M/T H6-a
INTEGRA ‘95.9∼‘01.6
(Including DC2 A/T H2-e
the ‘98 B18C A
DB8 M/T H3-b
specification) ‘93.5∼‘95.8
A/T H2-e
DA6 B16A ‘89.4∼‘93.4 C H1-a
EP3 K20A ‘01.12∼※ H9-a
EU2 Except the

D15B D
EU1 Lean Burn
‘00.9∼※ H10-a
EU4
D17A
CIVIC EU3
‘00.8∼‘00.9 H8-b
EK9 B16B ‘98.9∼‘00.7 A H7-c
‘97.6∼‘98.8 H6-a
38
‘98.9∼‘00.7 H7-a
EK4 B16A
‘95.9∼‘98.8 H6-a
‘98.9∼‘00.7 H7-a
EK3 D15B A
‘95.9∼‘98.8 H6-a
CIVIC
EG6 B16A H3-b
‘91.9∼‘95.8
Except the
EG4 D15B H3-a
Carburetor
EF9 B16A ‘89.9∼‘91.8 C H1-a PR-6
EG2 B16A A H3-b

‘92.3∼‘95.10
CR-X EG1 D15B B H3-a
EF8 B16A ‘89.9∼‘92.2 C H1-a
RD5 ‘01.9∼※
K20A D H11-a
RD4
CR-V RD2 H7-c
B20B ‘97.10∼‘01.8 Ａ
RD1 H2-b
RB2 H11-c
K24A ‘03.10∼※ B Absolute H11-c PR-18

RB1
H11-d
‘00.8∼’03.9
RA9
J30A
RA8 ‘00.1∼‘03.9
E H7-c
ODYSSEY
RA7 ‘99.12∼‘03.9
F23A
RA6
RA5 J30A ‘97.10∼‘99.11 H6-b
RA4 ‘97.8∼‘99.11
F23A C H7-c
RA3
RA2 ‘94.10∼‘97.7
F22B H3-a
RA1
PR-6
‘99.9∼‘02.1 H7-c
RH2
S-MX B20B E
RH1 ‘96.11∼‘99.8 H2-b
RF4 ‘01.4∼※
K20A H11-a
RF3
‘99.5∼‘01.3 H7-c
STEP RF2
‘96.5∼‘99.4 E H2-b
WAGON
B20B
‘99.5∼‘01.3 H7-c
RF1
‘96.5∼‘99.4 H2-b
39
RR2
ELYSION K24 ‘04.5∼ ※ E 2.4L Ｈ１１−ｃＰＲ−１８
RR1
RH2 ‘99.9∼ ‘02.1 Ｈ７−ｃ

S-MX E
RH1 B20B ‘96.11∼ ‘99.8 Ｈ２−ｂ
PR-6
T/C H5-b
Z PA1 E07Z ‘98.10∼ ‘02.1 N
NA H4-b
JB6 ‘03.9∼※ H10-ｂ

P07A B PR-18
JB5
LIFE ‘00.12∼‘03.8 H5-c

JB2
E07Z A
JB1 ‘98.10∼‘00.11 H5-d
JA4 E07A ‘97.4∼‘98.9 G H4-a
JB4 ‘00.12∼※
LIFE DUNK E07Z A H5-c
JB3
GA6 ‘99.10∼‘02.1
CAPA D15B A H5-a
GA4 ‘98.4∼‘02.1
RN4
K20A
RN3
STREAM ‘00.10∼※ D H11-a
RN2
D17A
RN1
GD4 ‘02.9∼※ PR-6

L15A
GD3
FIT GD2 ‘01.7∼※ B H10-a
L13A
GD1 ‘01.6∼※
GD9
L15A
GD8
FIT ARIA ‘02.12∼※ B H10-a
GD7
L13A
GD6
JD2 ‘02.2∼※
THAT’S E07Z D H5-c
JD1
GB2 ‘01.12∼※
MOBILIO L15A B H10-a
GB1
MOBILIO GK2 ‘02.9∼※

L15A B H10-a
SPIKE GK1
40
■ECU Terminal Arrangement Table (HONDA)
IG power Knocking signal Pressure signal

Knocking signal 2 Pressure signal
IG power
Ground rpm Throttle signal

※SOHC E/g no knocking signal is available Knocking signal 1
IG power Pressure signal IG power Knocking signal 1 Pressure signal
rpm Ground Throttle signal rpm Ground Knocking signal 2 Throttle signal
IG power Knocking signal 1 Pressure signal rpm IG power Knocking signal Pressure signal
rpm Ground Knocking signal 2 Throttle signal Ground Throttle signal
※There might not be free space of connector
Knocking signal 2 Pressure signal Pressure signal

IG power rpm IG power
Ground rpm Knocking signal 1 Ground Throttle signal

Throttle signal ※Without knocking signal
※There might not be free space of connector
rpm IG power Pressure signal Pressure signal IG power Ground
Ground Throttle signal Throttle signal rpm

Knocking signal ※Without knocking signal
41
Throttle signal IG power Pressure signal
IG power

Pressure signal rpm Ground
※Without knocking signal ※Without knocking signal
rpm rpm
IG power Pressure signal IG power Pressure signal
Ground Throttle signal Ground Knocking Throttle signal

signal
rpm
Ground IG power Pressure signal
IG power Pressure signal Throttle signal
Ground
rpm Knocking signal
Ground IG power Pressure signal rpm IG power Pressure signal

Throttle signal
Ground Throttle signal

※Without knocking signal rpm
rpm IG power Pressure signal Knocking signal rpm IG power Pressure signal
Ground Throttle signal Ground Knocking Throttle signal

signal
42
rpm IG power Knocking signal Pressure signal rpm IG power Pressure signal Knocking signal
Ground Throttle signal Ground Throttle signal
IG power Ground Throttle signal Knocking signal
Pressure signal rpm
IG power Ground Knocking signal
Pressure signal rpm

Throttle signal
IG power Ground
Throttle signal Pressure signal
rpm Knocking signal
Pressure signal rpm

Throttle signal
43
Knocking signal IG power Ground
Pressure signal
Throttle signal rpm
(case of K24A) Throttle signal (case of K20A)
IG power Ground
Knocking signal
knocking signal
is not available
Pressure signal
rpm
Throttle signal
Knocking signal
IG power Ground knocking signal is not available
Pressure signal rpm

Throttle signal
Knocking signal IG power Ground
Throttle signal rpm

Pressure signal
44
■Table of Applicable Models (MITSUBISHI)
HW-HotWire FL-Flap

‘97.8∼‘02.9 M5-a
F46A
‘96.1∼‘97.7 Without MIVEC M6-a KR
‘97.8∼‘02.9 M5-a
E With MIVEC M3-b PR-5
DIAMANTE 6G72 ‘96.1∼‘97.7
F36A Without MIVEC M6-a KR
With MIVEC M3-b PR-5

‘95.1∼‘95.12
M6-a
DOHC KR
F17A ‘90.5∼‘94.12 A M2-a
DIAMANTE ‘97.10∼‘02.9
F36W 6G7 E M6-b KR
WAGON
GTO Z16A 6G72 ‘90.10∼‘00.7 E M2-a KR
Without MIVEC
M6-a
A/T
‘97.2∼‘00.7 KR
Without MIVEC
M3-a
M/T
DE3A 6A12
FTO ‘94.10∼‘97.1 B With MIVEC M3-b PR-5
‘96.2∼‘00.7 M3-a
M2-a KR
‘94.10∼‘96.1
DE2A 4G93 M3-a
LEGNUM EC5W 6A13 ‘96.8∼‘02.8 E DOHC T/C M3-a KR
EC5A 6A13 ‘96.8∼‘02.8 M3-a

E DOHC T/C
GALANT E84A 6A12 ‘92.5∼‘96.7 M2-a KR
E39A 4G63 ‘87.10∼‘92.4 B DOHC M1-a
D32A ‘95.6∼‘99.12 M3-a

ECLIPSE 4G63 E KR
D27A ‘89.11∼‘95.5 M1-a
LIBERO CD5W 4G93 ‘92.5∼‘00.5 B M2-a KR
45
CP9A ‘98.1∼‘01.1 Including Ⅵ,TM

M3-a
CN9A ‘96.8∼‘97.12
4G63 KR
CE9A ‘93.10∼‘96.7
M2-a
LANCER CD9A ‘92.10∼‘93.9 B
CK4A 4G92 MIVEC M3-b PR-5

‘95.10∼‘00.5
CM5A M3-a
4G93 KR
CD5A ‘91.10∼‘95.9 M2-a
CQ5A 4G93 ‘00.2∼‘02.8

M6-c
‘00.1∼‘02.8 KR
MIRAGE
CQ2A 4G15 E
DINGO ‘98.12∼‘99.12 M3-a
CQ1A 4G13 ‘00.1∼‘02.8 M6-d PR-12
CM5A 4G93 T/C M3-a KR

‘95.10∼‘00.5
MIRAGE CJ4A B M3-b
4G92 MIVEC PR-5
CA4A ‘91.10∼‘95.9 M2-a
‘00.7∼※ M6-a
V75W
V65W ‘99.9∼※
6G74 A/T M6-c
PAJERO A KR
V25W ‘93.7∼‘99.1 M2-a
V23W 6G72 ‘92.6∼‘97.4 M1-a
N64WG ‘99.10∼‘02.8 C
4G64
N74WG M3-a
‘97.11∼‘02.8 B M/T
N73WG 4G63
RVR A/T M6-a KR
‘99.10∼‘02.8 C M6-c
N71W
4G93
N61W ‘97.11∼‘99.9 B M3-a
N23W 4G63 ‘91.2∼‘97.10 B M2-a
‘02.9∼※ M3-d
ek WAGON H81W 3G83 B PR-12
‘01.10∼‘02.8 M4-a
ek SPORTS H81W 3G83 ‘02.9∼※ B M3-d PR-12
46
N96W ‘99.10∼‘03.4
6G72
N86W
M6-c
CHARIOT ‘00.5∼‘03.4
C
GRANDIS N94W
4G64 Without
N84W ‘97.10∼‘00.4 Cruise M3-c
Control
H77W 4G94 ‘00.6∼※
H76W 4G93 ‘00.7∼※ T/C M5-a

PAJERO io D
H6#W ‘98.10∼‘00.6
4G94
H72W ‘00.6
LANCER
EVOLUTION CT9A 4G63 ‘04.2∼※ D M5-a
Ⅷ MR KR
LANCER
CT9A 4G63 ‘03.1∼‘04.1 D M5-a
EVOLUTION Ⅷ
LANCER ‘01.2∼‘02.3 M3-a

CT9A 4G63 D
EVOLUTION Ⅶ
‘02.2∼‘02.12 A/T M6-a
LANCER ‘00.５∼‘03.1
CS5A 4G93 D M6-c
CEDIA
LANCER ‘00.11∼‘03.1
CS5W 4G93 D M6-c
CEDIA WAGON
CU4W 4G64 ‘01.6∼※ M7-a
AIRTREK ‘02.6∼※ E T/C

CU2W 4G63 M6-a
‘01.6∼※
47
■ECU Terminal Arrangement Table (MITSUBISHI)
Knocking signal Airflow signal rpm Knocking signal

rpm
Ground IG power Throttle signal IG power Ground Throttle signal

Airflow signal/pressure signal
※In E39A, a knocking signal is available for TURBO only
※In V23W, no knocking signal is available ※In CD5W, a knocking signal is available for DOHC only
Airflow signal Knocking signal

Knocking signal Throttle signal
IG power Ground rpm Throttle signal IG power Ground rpm Pressure signal
※DE2A, no knocking signal is available
Knocking signal Airflow signal Pressure signal Knocking signal
IG power rpm Throttle signal IG power Ground rpm Throttle signal

Ground
Pressure signal
IG power Throttle signal rpm Ground IG power
Airflow signal Throttle signal

Ground rpm Knocking signal
Ground
IG power rpm Throttle signal IG power Ground Throttle signal
Airflow signal Knocking signal rpm Airflow signal

48
Ground Ground
IG power rpm IG power rpm
Throttle signal
Airflow signal Knocking Pressure signal Knocking signal Throttle signal
signal
IG power Airflow signal

Ground
rpm Knocking signal Throttle signal
49
■Table of Applicable Models (MAZDA)
HW-HotWire FL-Flap

JC3S ‘94.3∼‘95.8
13B-REW
JC3SE ‘90.3∼‘94.2
C
EUNOS COSMO
B◎ Z3-a FL-6
JCES ‘94.3∼‘95.8
20B-REW
JCESE ‘90.3∼‘94.2
‘95.12∼‘02.8 Z4-a
FD3S 13B-REW A PR-4
‘91.12∼‘95.11 Z3-b
RX-7
‘88.9∼‘91.11 Z2-a FL-6
FC3S 13B C
‘85.9∼‘88.8 Z1-a FL-5
‘95.8∼‘97.12 Z6-a
NA8C BP-ZE HW-11
‘93.8∼‘95.7 Z5-a
ROADSTER C
M/T Z5-c
NA6CE B6-ZE ‘89.9∼‘93.7 FL-8
A/T Z5-a
4WD M/T
Z3-c
ZL-DE ‘98.6∼‘03.6 4WD A/T
BJ5P 2WD Z8-a

D HW-22
FAMILIA ‘98.9∼‘99.7 M/T
ZL-VE
‘98.6∼‘01.11 A/T Z3-c
BJ3P B3-ME ‘98.6∼‘02.8
BG8Z BP-ZET ‘89.8∼‘94.3 E Z5-b FL-7
M/T Z7-a
MD22S K6A T/C
‘00.12∼※ A/T Z7-b
AZ-WAGON MD12S F6A T/C L Z7-c PR-8
MD21S K6A T/C

‘98.10∼‘00.11 Z7-a
MD11S F6A T/C
DY5W ZY-VE ※１
DEMIO ‘02.8∼※ L Z9-a HW-22
DY3W ZJ-VE ※１
※１ This product rpm amount is collect,even if the difference will be

◎：EC-AT position
happen between stock rpm meter and S-AFCⅡ
50
GGES LF-DE
‘02.5∼※
ATENZA
C Z10-a
SPORT
GG3S L3-VE
‘02.10∼※ M/T
GYEW LF-DE
‘02.5∼※
ATENZA
C Z10-a
SPORT WAGON
GY3W L3-VE HW-22
‘02.10∼※ M/T
GGEP LF-DE
ATENZA ‘02.5∼※ C Z10-a
SEDAN
GG3P L3-DE
MPV LW3W L3-DE ‘02.4∼※ D Z10-b
VERISA DC5W ZY-VE ‘04.6∼※ L Z9-a
51
■ECU Terminal Arrangement Table (MAZDA)
IG power Airflow signal Ground Ground Throttle signal rpm
Throttle signal rpm Knocking signal Knocking signal Airflow signal IG power
Knocking signal 2 Knocking signal 1


※Only the knocking signal 1 of 13B-REW
※The turn signal connects with EA-AT(Z3-AT)
Ground Throttle signal Pressure signal Throttle signal Ground rpm Knocking signal
rpm IG power Airflow signal IG power

Knocking signal
rpm Throttle signal

Throttle signal rpm IG power

Pressure signal IG power Knocking signal Ground
Airflow signal Ground rpm Airflow signal Ground
IG power rpm IG power

Throttle signal Knocking signal
52
Knocking signal
rpm IG power Ground (Only K6A)
rpm
IG power Airflow signal
Pressure signal Throttle signal
Ground Knocking signal Pressure signal Knocking signal

rpm IG power rpm IG power
Pressure signal Throttle signal Ground Throttle signal
This product rpm amount is collect,even if the

difference will be happen between stock rpm
meter and S-AFCⅡ
Knocking signal rpm

IG power Knocking signal Ground

Airflow signal Throttle signal rpm Ground
Airflow signal
Knocking
IG power signal Throttle signal
rpm (Set the number of cylinders to 2 at initial setup )

※In GG#P, GG#S, and GY#W, a knocking signal is not available
IG power Knocking signal Throttle signal

Airflow signal
Ground
rpm
53
■Table of Applicable Models (SUBARU)
HW-HotWire FL-Flap
BE9 EJ254 F5-b HW-16
EJ208 ‘01.5∼‘03.4 F8-c HW-20

EJ206
LEGACY B4 EJ204 C F5-b HW-16
BE5
EJ208 HW-20
‘98.12∼‘01.4 F4-a
EJ204 HW-16
EJ208
F8-c HW-20
EJ206
BH5
EJ204 ‘01.5∼‘03.4
F5-b HW-16
BH9
LEGACY EJ254
BHC
TOURING C
WAGON EJ208
HW-20
EJ206
BH5
EJ204 ‘98.6∼‘01.4 F4-a
HW-16
BH9
EJ254
BHC
EJ20R HW-1
M/T F1-b
‘96.6∼‘98.5
BD5
EJ20H C A/T F3-a
BG5 HW-4
EJ20D
T/C F2-a
‘93.10∼‘96.5
LEGASY NA F1-a
BC5 ‘89.2∼‘93.9
EJ20G H F2-b HW-10
BF5
‘96.6∼‘98.5 F3-a
BD9
EJ25D C HW-4
BG9 ‘94.10∼‘96.9 F1-a
M/T F8-a
SG5 ‘02.2∼※ D HW-20
EJ205 A/T F8-b
FORESTER
‘98.9∼‘02.1 F4-a HW-1
SF5 C
EJ20G ‘97.2∼‘98.8 F1-b HW-4
54
GDB ‘00.10∼※ Including

EJ207
GGB Spec C
F8-a HW-20
GDA
EJ205
GGA
GD9 ‘00.8∼※
EJ204 F5-b HW-16
GG9
GG3
IMPREZA EJ152 C M/T F5-a PR-8
GG2
EJ207 ‘98.9∼‘00.7 F4-a

EJ205
HW-1
GC8 EJ20K
GF8 ‘96.9∼‘98.8 F1-b
HW-4
EJ20G
‘92.11∼‘96.8 F2-b HW-10
EN07E SOHC NA
EN07Z ‘01.10∼※ SOHC S/C F6-a
EN07X DOHC S/C

RA2
PLEO B SOHC S/C PR-14
RA1
（Except the F2-ｄ
EN07 ‘98.10∼‘01.9 Mild Charge）
DOHC S/C F2-d
55
■ECU Terminal Arrangement Table (SUBARU)
Knocking signal
Knocking signal Airflow signal IG power
Airflow signal
rpm Ground Throttle signal rpm Ground

IG power Throttle signal
Airflow signal Knocking signal

Ground Knocking signal Throttle signal Airflow signal
rpm Throttle signal IG power rpm Ground IG power
Throttle signal Pressure signal Pressure signal

IG power IG power Throttle signal
rpm Ground Ground

Knocking signal rpm Knocking signal
Knocking signal IG power

rpm Throttle signal Ground rpm Throttle signal Knocking signal
Throttle signal
Knocking signal IG power IG power
Throttle signal Ground Knocking signal
rpm Pressure signal Ground rpm Airflow signal
56
Ground Throttle signal Pressure signal Knocking signal
IG power Throttle signal rpm
rpm IG power Ground

Knocking Pressure signal
signal
IG power
rpm Throttle signal Knocking signal
IG power Throttle signal Airflow signal Knocking signal
Ground
rpm
IG power
rpm Throttle signal Knocking signal
57
■Table of Applicable Models (SUZUKI)
HW-HotWire FL-Flap
With VVT S8-a

HA22S K6A T/C
‘98.10∼‘00.12 L S6-a
HA12S F6A T/C S6-b

ALTOWORKS PR-8
HA21S
K6A T/C S3-a
HB21S
‘94.11∼‘98.9 B
HA11S M/T S2-a
F6A T/C
HB11S A/T S4-a
EA21R K6A T/C ‘95.5∼‘98.6 K S5-a

CAPPUCCINO PR-8
EA11R F6A T/C ‘91.11∼‘95.10 B S1-a
MH21S ‘03.9∼※ Mild Turbo PR-17
‘01.11∼‘03.8 S7-b
K6A T/C
MC22S M/T S6-a
‘00.12∼‘03.8
L A/T S7-b
MC12S F6A T/C ‘00.12∼‘01.4 S6-c
MC21S K6A T/C

‘98.10∼‘00.11 S6-a
WAGON R
MC11S F6A T/C PR-8
CT51S ‘97.4∼‘98.9
K6A T/C S5-a
CV51S
‘95.10∼‘97.10 M/T S2-a

B
CT21S ‘95.10∼‘98.5 A/T S4-a
F6A T/C
CV21S
M/T S1-a
‘93.9∼‘95.9
A/T S4-a
WAGON R ‘99.5∼‘00.11
MA63S K10A T/C B S9-b PR-8
PLUS
WAGON R MA61S ‘97.2∼‘99.12

K10A T/C B S5-a PR-8
WIDE MB61S
MA34S M13A ‘00.12∼※ S9-c PR-13

WAGON R
B
SOLIO ‘00.12∼‘02.10
MA64S K10A S9-b PR-8
K6A T/C S7-b PR-8

MR WAGON MF21S ‘01.11∼※ L
K6A S7-a PR-13
58
Engine Manufacturin ECU Terminal Sensor
Car Name Car Model Remarks
Model g year Position Drawing Type
M/T S6-a
K6A T/C PR-8
HN22S A/T S7-b
‘01.4∼※
Kei K6A L PR-13

HN12S S6-a
HN21S K6A T/C

‘98.10∼‘01.3 PR-8
HN11S F6A T/C S6-b
JB23W ‘98.10∼※ L S6-a

K6A T/C
JIMNY JA22W S3-a PR-8
‘95.11∼‘98.9 B M/T
JA12W F6A T/C S2-b
K6A T/C ‘03.10∼※ S7-b PR-17

ALTO ‘02.1∼※
HE21S K6A T/C L S7-a PR-13
LAPIN
K6A ‘02.10∼※ S7-b PR-17
CHEVROLET ‘01.10∼※
HR51S M13A L S9-a PR-13
CRUISE
※In some SUZUKI vehicles, A HITACHI pressure sensor is used instead of the
conventional MITSUBISHI pressure sensor. If any engine malfunction or defect is
detected when the sensor type mentioned in the above table is set, check the
manufacturer name of the pressure sensor used in the vehicle. If the HITACHI
pressure sensor is used, set the sensor type to PR-17
59
■ECU Terminal Arrangement Table (SUZUKI)
rpm IG power Ground

rpm IG power Ground
Pressure signal Pressure signal
※Without knocking signal and throttle signal ※Without knocking signal and throttle signal
Knocking
rpm IG power Ground Ground signal IG power
rpm
Pressure signal Pressure signal Throttle signal
rpm Ground IG power rpm IG power

Pressure signal Ground Pressure signal
Throttle signal
Throttle signal Knocking
signal
IG power Ground
rpm Pressure Throttle signal

rpm Pressure Throttle signal signal
signal ※Without knocking signal
IG power Ground Knocking signal rpm IG power Ground Knocking signal
rpm Pressure signal

Pressure signal Throttle signal Throttle signal
60
rpm IG power Ground Knocking signal
Pressure signal Throttle signal

※knocking signal is not available HE21S
Knocking signal Pressure signal

Throttle signal
Ground rpm IG power
Throttle signal Ground IG power Ground IG power Throttle signal
Pressure signal Knocking signal rpm Pressure signal Knocking signal rpm
Throttle signal Ground IG power
Pressure signal Knocking signal rpm
61
■Table of Applicable Models (DAIHATSU)
HW-HotWire FL-Flap

L260S ‘02.12∼※
MIRA AVY EF-DET D D5-a PR-8
L250S
L710S ‘98.10∼‘00.9
MIRA EF-DET D D2-a PR-8
L700S
MIRA L512S ‘94.9∼‘98.9

JB-JL D D1-a PR-8
TR-XX L502S
L152S JB-DET PR-15

‘02.10∼※ D5-a
L160S
L150S
EF-DET ‘01.10∼‘02.9 D3-a PR-8
L900S
‘00.10∼‘01.9 D4-a
MOVE L902S JB-DET D PR-15
‘01.10∼‘02.9 D3-a
L910S EF-DET PR-8
L902S JB-DET PR-15

‘98.10∼‘01.9 D4-a
L910S EF-DET
PR-8
L602S JB-JL ‘95.8∼‘98.9 D1-a
COPEN L880K JB-DET ‘02.6∼※ D D3-a PR-15
L952S JB-DET PR-15

MAX ‘01.10∼※ D D3-a
L960S EF-DET PR-8
BOON M300S 1KR-FE ‘04.6∼※ D D5-b PR-20
62
■ECU Terminal Arrangement Table （DAIHATSU）
Pressure Pressure signal IG power

Ground IG power signal Ground
rpm Knocking signal rpm

Throttle signal
Knocking signal
Pressure signal IG power Ground IG power
Throttle signal Pressure signal rpm

Ground Knocking signal Throttle signal rpm
Knocking signal
Pressure signal Throttle signal IG power IG power Ground Pressure signal
※ Set the number of

Ground Knocking signal rpm rpm Knocking
Throttle signal cylinders “1” at intial setting.
signal 〔etc.→Car sel.→Cｙｌ 1〕
63
Notes
1. The contents of this document are subject to change without prior notice
2. The contents of this document have been prepared with extreme care. However,
if you find, error, or other fault, please inform us of it
3. A part or all of this document may not be reproduced in any form without prior
written permission, and also may not used without the prior written permission of
APEXERA CO., LTD. under the copyright except for private use.
・The company names and product names described in this document

are the registered trademarks or brands of the respective companies
・The names, addresses and telephone numbers mentioned as where
to contact are as of February 1, 2005. Note that this information is subject
to change
■Revision Record
No. Date of issue Part No. of instruction manual Edition Change of description
1 Dec. 10, 2002 7107-0240-00 First edition
2 May. 1 ,2003 7107-0240-01 2nd edition
3 Jun. 1 ,2004 7107-0240-02 3rd edition
4 Sep. 30 ,2004 7107-0240-03 4th edition
5 Feb. 1 , 2005 7107-0240-04 5th edition
APEXERA Co.,Ltd. http://www.apexera.co.jp

Head office : 1-17-14 Tanashioda,Sagamihara-city Kanagawa,229-1125 JAPAN
ph+81-42-778-3991 fx+81-42-778-4495
USA office
A’pex Integration,Inc.: 330W.Taft Orange,CA.92865,USA
ph : (714)685-5700 fx : (714)685-5701
64

Apexi Installtion Instruction Manual: S-AFC 2 / SUPER AIR FLOW CONVERTER WIRING DIAGRAM

Uploaded by

Copyright:

Available Formats

Apexi Installtion Instruction Manual: S-AFC 2 / SUPER AIR FLOW CONVERTER WIRING DIAGRAM

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Apexi Installtion Instruction Manual: S-AFC 2 / SUPER AIR FLOW CONVERTER WIRING DIAGRAM

Uploaded by

Copyright:

Available Formats

SUPER

This document describes car models to which the Super Airflow

■ECU Arrangement Diagram__________________________________P12

●When removing or connecting a connector, be sure to unlock the

●Insulate the metallic portion of the harness securely with electrical

●Caulking the plug

(1) Peel off the coating of (4) Caulk securely

Caulk the conductors by these portions

Caulk the coating by these portions

●Caulking the splice

※Insulate the caulked portion securely with a vinyl tape

Correct Connecting Method for the Ground Conductor

Brown wire (ground)

Unite the ground

Do not connect the

1.Remove the negative (ー) terminal of the battery

Connect the red wire to the power supply.

※For models with a single knocking wire.

※For models with multiple knocking wires (knocking signal 1,

●Securely install the splice without any loose contacts.

Plug ：ECU side

Vehicles equipped with the RB26DETT have 2 airflow signal wires.

For Hot Wire/ Plug receptacle: White wire

Plug receptacle: Orange wire

6.Insulate the splice and unused plug with electrical tape.

7.Reconnect the negative (ー) terminal of the battery.

Red wire (power supply)

Harness for branching

Yellow wire (airflow/pressure signal output)

Red wire (power supply)

●Do not install the SAFC II in a high-temperature place or in a location

●Turn on the ignition switch. (Do not start the engine.)

Connect the airflow or pressure signal wire

Make checks after completion of installation

With the ignition switch ON

Page 10 in this document

A : Lower part of the passenger seat dash side

This ECU terminal arrangement diagram is viewed from the

The direction of the ECU varies depending upon the vehicle.

Manufacturing ECU Terminal Sensor

’97.7∼‘00.7 L T10-e HW-13

JZS171 1JZ-GTE T10-b HW-23

JZS171W 1JZ-GTE T10-b HW-23

CROWN JZS14# 2JZ-GE ‘91.10∼‘95.7 D T8-b PR-3

JZS161 2JZ-GTE ‘97.8∼※

ARISTO 2JZ-GTE PR-1

UZS143 1UZ-FE ‘92.10∼‘97.7 T7-b KR

UZZ40 3UZ-FE ‘01.4∼※ L T11-b HW-25

‘96.8∼‘01.3 T8-d HW-12

JZZ31 2JZ-GE ‘94.1∼‘96.7 C T8-b PR-3

‘97.8∼‘02.8 T10-c HW-13

JZA70 1JZ-GTE ‘90.8∼‘93.4 T6-a PR-1

‘88.8 Turbo A PR-1

JZX110 1JZ-GTE ‘00.10 T10-b HW-23

JZX110W 1JZ-GTE T10-b HW-23

VEROSSA JZX110 1JZ-GTE ‘01.8∼‘04.4 L T10-b HW-23

SW20 ‘97.12∼‘99.10 T9-b HW-13

MR2 ‘93.10∼‘97.11 M T6-b

4A-GZE ‘86.8∼‘89.9 T2-a FL-3