Mechanical Measurement ME 302 Assignment (3) : Presentation of Results Question (1) Calibration Curve For Orifice Meter
Uploaded by
Mohamed MaherMechanical Measurement ME 302 Assignment (3) : Presentation of Results Question (1) Calibration Curve For Orifice Meter
Uploaded by
Mohamed MaherMECHANICAL MEASUREMENT
ME 302
ASSIGNMENT (3)
PRESENTATION OF RESULTS
QUESTION (1)
Calibration Curve for Orifice Meter.
Given that the calibration constant C=0.85
Take internal diameter of the pipe = 0.8m
Take velocity V as given in TABLE (1) .
Find the volume flow rate using Q= A*V, where A is the cross section area of the pipe. Take the
density of water corresponding to room temperature of 200C.
Q 2
Use the relation
P * (
) to calculate P for various values of Q.
2 C*A
Plot the graph P and Q.
Find the static sensitivity at various flow rates from the graph and the equation.
Plot K vs Q
TABLE (1)
S.No Student Number
QUESTION (1)
Velocity Values
2,3,4,5,6,7
1
423101791
2.5,3.5,4.5,5.5,6.5,7.5
2
424117199
5.5,6,6.5,7,7.5,8
3
425103782
,2.5,4.5,6.5,8.5,10.5,12.5
4
425104014
1.5,2.5,3.5,4.5,5.5,6.5
5
426101335
7.5,8,8.5,9,9.5,10,11
6
426101886
8.5,9,9.5,10,10.5,11,12
7
426101889
9,9.5,10,10.5,11,11.5,12.5
8
426101957
10.5,11.5,12.5,13.5,14.5,15.5
9
426103283
10,11,12,13,14,15
10
426103342
11.5,12.5,13.5,14.5,15.5,16
11
426113260
12,14,16,17,18,18.5
12
427102035
12.5,13.5,14.5,15.5,16,16.5
13
427102366
15.5,17.5,19.5,21.5,22,22.5
14
427102404
11,13,15,17,19,20.5
15
427102584
3,5,7,9,11,12.5
16
427102679
12,13,14,15,16,16.5
17
427102762
13,13.5,14,14.5,15,15.5
18
427102904
10.5,11.5,12.5,13.5,14.5,15.5
19
427103694
20
427104125
QUESTION (2)
The following data was obtained during an experimental run.
(a) Using linear graph paper plot the data as log-log graph, semi log graph,
linear graph and ln- ln graph.
x
70700
66600
51000
23000
30900
36242
52331
70000
84100
21810
33217
44000
56700
63000
87276
82200
83092
93800
Y
175
168
138
81
99
109
142
168
191
76
117
144
146
157
197
201
192
208
QUESTION (3)
Given the following calibration data for a measuring system:
Input X
Output Y
2
3
4
10
8
27
10
44
12
65
The expected relation is: Y = b Xn
Transfer the above calibration data to straight line relation and find the
values of b and n.
Draw the relation between X and the static sensitivity of the system
