Chapter 3

Chapter 3 Error Code

3.1 Error Code Details
3.1.1 Error Code Details
iR7105 / iR7095 / iR7086 /
T-3-1 Code Description Remedial action *: model equipped with DADF-Q1 (outside Japan, iR7105/7095; inside Japan: iR7105/7095/7086). **: model equipped with DADF-M1 (outside Japan: iR7086). E000 The fixing unit has overheated. After correcting the fault, be sure to reset the error. (COPIER>FUNCTION>CLEAR>ERR) 0000 The reading of the main thermistor is less than 70 deg C 3.5 min after power- Check the mounting/soiling of the main thermistor. Replace on. the fixing heater. Replace the main thermistor. Replace the AC driver PCB. Replace the DC controller PCB. 0010 The power has been turned off and then on without resetting the error. E001 Reset the error. (COPIER>FUNCTION>CLEAR>ERR) The fixing unit has overheated. After correcting the fault, be sure to reset the error. (COPIER>FUNCTION>CLEAR>ERR) 0001 The reading of the main thermistor or the sub thermistor is 230 deg C or more Replace the AC driver PCB. Replace the DC controller PCB. for 2 sec. (hardware detection) 0002 The reading of the main thermistor or the sub thermistor is 230 deg C or more Check the mounting/soiling of the main thermistor. Replace for 2 sec or the main thermistor. Replace more. (software detection) the sub thermistor. Replace the AC driver PCB. Replace the DC controller PCB. 0003 The difference in the readings of the main thermistor and the sub thermistor is Check the mounting/soiling of the main thermistor. Replace 50 deg C for the main thermistor. Replace 1 sec. (main thermistor reading>sub thermistor reading) the AC driver PCB. Replace the DC controller PCB. 0004 The difference in the readings of the main thermistor and the sub thermistor is 50 deg C for 1 sec or more. (main thermistor reading>/=sub thermistor reading) 0010 The power has been turned off and then on without resetting the error. E002 Reset the error. (COPIER>FUNCTION>CLEAR>ERR) The fixing unit has overheated. After correcting the error, be sure to reset the error. (COPIER>FUNCTION>CLEAR>ERR) 0000 The reading of the main thermistor has exceeded 70 deg C, but does not reach Disconnect and then connect J508 of the DC controller PCB. 100 deg C Disconnect and then connect within 2.5 sec thereafter. the connectors of the fixing unit. Check the wiring between 0001 The reading of the main thermistor has exceeded 100 deg C, but does not reach the main/sub thermistor and the DC controller. Check the mounting/soiling of the main 150 deg C thermistor. Replace the fixing within 2.5 min thereafter. heater. Replace the AC driver PCB. Replace the DC controller PCB. 0010 The power has been turned on without resetting the error. E003 Reset the error. (COPIER>FUNCTION>CLEAR>ERR) The fixing unit temperature is abnormally low. After correcting the fault, be sure to reset the error. (COPIER>FUNCTION>CLEAR>ERR) 0000 The reading of the main thermistor has exceeded 100 deg C, but is 70 deg C Disconnect and then connect J508 of the DC controller PCB. or less for 2 sec Disconnect and then connect thereafter. the connectors of the fixing unit. Check the wiring between the main/sub thermistor and the DC controller PCB. Check the mounting/soiling of the main thermistor. Replace the fixing heater. Replace the AC driver PCB. Replace the DC controller PCB. E004 The fixing unit has a fault. (protective circuit ON) After correcting the fault, be sure to reset the error. (COPIER>FUNCTION>CLEAR>ERR) 0000 While the sub heater is on, the SSR for the heater drive has a short-circuit for Replace the AC driver PCB. Replace the DC controller PCB. 5 sec or more. 0001 While the main heater is on, the SSR for the heater drive has a short-circuit for 5 sec or more. E005 The fixing web has run out. After correcting the fault, be sure to reset the error. (COPIER>FUNCTION>CLEAR>ERR) 0000 The absence of the fixing web has been detected for 5 sec or more. Check the position of the fixing web detecting lever. Replace the fixing web. Replace the fixing web length sensor. Replace the DC controller PCB. If you have replaced the fixing web, be sure to reset the counter: - COPIER>COUNTER>MISC>FIX-WEB - COPIER>COUNTER>DRBL-1>FX-WEB 0010 The power has been turned off and then on without resetting the error. E010 The main motor rotation is faulty. Reset the error. (COPIER>FUNCTION>CLEAR>ERR)
0011-6725

37

Chapter 3
Code Description Remedial action

*: model equipped with DADF-Q1 (outside Japan, iR7105/7095; inside Japan: iR7105/7095/7086). **: model equipped with DADF-M1 (outside Japan: iR7086). 0000 After the main motor has gone on, the FG signal of the motor is not detected Disconnect and then connect J611 and J612 of the main for 2 sec or motor. Disconnect and then connect more. J514 of the DC controller PCB. Disconnect and then connect J1720 of the relay PCB. Replace the main motor. Replace the relay PCB. Replace the DC controller PCB. E012 The drum motor rotation is faulty. 0000 After the drum motor has gone on, the PLL lock signal of the motor is not detected for 2 sec or more. Disconnect and then connect J1721 of the relay PCB. Disconnect and then connect J512 of the DC controller PCB. Disconnect and then connect J601 and J602 of the drum motor. Replace the drum motor. Replace the DC controller PCB.

E013

The waste toner feedscrew is stuck. (clogged with waste toner) After correcting the fault, be sure to reset the error. (COPIER>FUNCTION>CLEAR>ERR) 0000 The waste toner feedscrew is stuck for 4 sec or more. Detach and then attach the waste toner pipe. Replace the waste toner pipe. Replace the waste toner feedscrew detecting switch. Replace the DC controller PCB. Reset the error. (COPIER>FUNCTION>CLEAR>ERR)

0010 The power has been turned off and then on without resetting the error. E014 The fixing motor rotation is faulty.

0000 After the fixing motor has gone on, the PLL signal of the motor is not detected Disconnect and then connect J651 and J652 of the fixing for 2 sec or motor. Replace the fixing motor. more. Replace the relay PCB. Replace the DC controller PCB. E015 The pickup motor rotation is faulty. 0000 The pickup motor has gone on, but the FG signal of the motor is not detected Disconnect and then connect J621 and J622 of the pickup for 2 sec or motor. Replace the pickup motor. more. Replace the relay PCB. Replace the DC controller PCB. E019 The waste toner case is full. 0000 After the waste toner case has become full, 50,000 prints (A4) or more have been made without disposing of the waste toner. Dispose of the waste toner. Check the operation of the waste toner bottle base. Disconnect and then connect J514 of the DC controller PCB. Replace the waste toner case full sensor. Replace the DC controller PCB.

E020

The developing assembly is out of toner. The buffer motor rotation is faulty. The toner feed motor (sub hopper) rotation is faulty. After correcting the fault, be sure to reset the error. (COPIER>FUNCTION>CLEAR>ERR) 0001 The absence of toner inside the developing assembly is detected of 120 sec or Disconnect and then connect the connector (J504, J512) of the more even DC controller PCB. when toner supply operation has been executed for the assembly. Replace the developing cylinder clutch (CL4). Replace the buffer motor (M18). Replace the magnet roller drive clutch (CL1). 0002 The absence of toner in the buffer is detected for 60 sec even after toner supply Disconnect and connect the connector (J504, J511) of the DC operation for the buffer has been executed and when there is toner inside the controller PCB. Replace hopper. the buffer motor (M18). Replace the following: magenta roller drive clutch (CL1), toner 0003 The absence of toner inside the buffer is detected for 210 sec or more even transport motor (sub hopper; M22), toner transport clutch when there is (sub hopper; CL23), buffer toner inside the sub hopper and after toner supply operation of that buffer inside toner sensor (TS1), buffer inside toner lower limit following the sensor (TS2). replacement of the toner bottle. 0004 The absence of toner inside he buffer is detected for 150 sec or more even when there is toner inside the buffer and after toner supply operation has been executed for the buffer following the replacement of the toner bottle. 0005 When installation mode (COPIER>FUNCTION>INSTALL>TONER-S) is Disconnect and then connect the connector (J504) of the DC executed, the controller PCB. Replace developing assembly inside toner sensor does not detect the presence of toner. the developing assembly inside toner sensor (TS3). 0006 When installation mode (COPIER>FUNCTION>INSTALL>TONER-S) is executed, the developing assembly inside toner sensor detects the presence of toner, but it does not detect the presence for 600 sec or more thereafter. 0007 When installing mode (COVER>FUNCTION>INSTALL>TONER-S) is executed, the buffer inside toner sensor does not detect the presence of toner for 60 sec or more. Disconnect and connect the connector (J504, J511) of the DC controller PCB. Replace thetoner transport motor (sub hopper; M22), toner transport clutch (sub hopper; CL23), buffer inside toner sensor (TS1).

0008 When the toner feed motor (sub hopper) is driven, a fault is detected for 3 sec Disconnect and connect the connector (J511) of the DC or more controller PCB. Replace the for the motor. toner feed motor (sub hopper; M22). 0009 There is a fault in the rotation of the buffer motor. Disconnect and then connect the connector (J504) of the DC controller PCB. Replace the buffer motor (M18). Reset the error. (COPIER>FUNCTION>CLEAR>ERR)

0010 The power has been turned off and then on without resetting the error. E025 The toner bottle motor rotation is faulty.

38

Chapter 3
Code Description Remedial action

*: model equipped with DADF-Q1 (outside Japan, iR7105/7095; inside Japan: iR7105/7095/7086). **: model equipped with DADF-M1 (outside Japan: iR7086). 0000 A toner bottle motor error (over-current) is detected for 10 sec for a second Disconnect and then connect J512 of the DC controller PCB. time. MEMO: The 1st detection of the error will cause the machine to indicate the message "Shake and Replace the Toner Container." 0001 The toner bottle motor is not connected. E032 The copy data controller/NE controller counter fails to operate. 0001 An open circuit of the counter signal has been detected. Disconnect and then connect J1022 of the main controller PCB. Replace the copy data controller/NE controller. Replace the main controller PCB. Disconnect and then connect J101 and J106 of the side paper deck driver PCB. Replace the pickup motor. Replace the side paper deck driver PCB. Replace the DC controller PCB.

E043

The rotation of the pickup motor of the side paper deck is faulty. 0000 The side paper deck pickup motor has gone on, but the PLL lock signal is not detected for 2 sec or more (1st detection). MEMO: For the 2nd and subsequent detection, the machine will indicate "E043" on the screen offering a choice of sources of paper.

E051

The horizontal registration HP detection has an error. 0001 After the start of horizontal registration HP detection, the HP sensor is not off within 5 sec (i.e., not leaving home position). MEMO: If an error is detected in the course of horizontal registration HP detection at power-on, the machine will indicate the presence of a jam. 0002 After the start of horizontal registration HP detection, the home position is not detected within 5 sec. MEMO: If an error is detected in the course of horizontal registration HP detection at power-on, the machine will indicate the presence of a jam. 0003 Replace the horizontal registration HP sensor. Replace the horizontal registration motor. Replace the stackless transport driver PCB. Replace the DC controller PCB. At the start of horizontal registration detection in the course of printing, the horizontal registration detection operation for downstream paper does not end within 5 sec.

E065

The high-voltage output has a fault. (primary charging assembly) 0000 A fault (leak) is detected when high voltage is supplied to the primary charging assembly. Remove and then mount the primary charging assembly. Check for soiling. Disconnect and then connect T601, J723, and J731 of the HV-DC PCB. Replace the HV-DC PCB.

E067

The high-voltage output has a fault. 0000 A fault is detected at the same time in 2 of the following: primary high voltage, Remove and mount the primary charging assembly. Remove pre-transfer and mount the pre-transfer high voltage, transfer high voltage, separation high voltage. charging assembly. Remove and mount the transfer/ separation charging assembly. Disconnect and then connect J721, J723, J731, and J734 of the HV-DC PCB. Replace the HV-DC PCB. Replace the HV-AC PCB.

E068

The high-voltage output has a fault. (separation charging assembly) 0000 A fault (leak) has been detected while the separation charging assembly is being supplied with high voltage. Remove and mount the transfer/separation charging assembly. Disconnect and then connect J7233 and J734 of the HV-DC PCB. Disconnect and then connect J741 and J742 of the HV-AC PCB. Replace the HV-AC PCB. Replace the transfer/ separation charging assembly. Replace the pre-transfer charging assembly.

E069

The transfer high voltage has an error. 0000 A fault (leak) has been detected while the transfer charging assembly is being Remove and mount the transfer/separation charging supplied with assembly. Check for soiling. high voltage. Disconnect and then connect T701 and J723 of the HV-DC PCB. Replace the HV-DC PCB. Replace the pre-transfer charging assembly.

E102

A read error has occurred in relation to the laser scanner unit EEPROM data. 0001 The correction data cannot be read from the EEPROM of the laser scanner unit. Disconnect and then connect the connector of the video PCB. Disconnect and then connect the DC controller PCB. Replace the laser scanner unit.

E110

The laser scanner motor rotation has a fault. 0000 After the laser scanner motor has gone on, the PLL lock signal of the motor is Check to see if all covers have been attached to the primary not detected charging assembly. Disconnect for 15 sec or more. and then connect J764 of the laser scanner motor drive PCB (in the laser scanner unit). Disconnect and then connect J1401 of the video PCB. Disconnect and then connect J506 of the DC controller PCB. Replace the laser scanner unit. Replace the video PCB. Replace the DC controller PCB.

E111

The laser scanner motor cooling fan rotation has a fault.

39

Chapter 3
Code Description Remedial action

*: model equipped with DADF-Q1 (outside Japan, iR7105/7095; inside Japan: iR7105/7095/7086). **: model equipped with DADF-M1 (outside Japan: iR7086). 0000 After the laser scanner motor cooling fan has gone on, the fan stop signal is detected for 5 sec or more. E121 Disconnect and then connect J503 of the DC controller PCB. Replace the laser scanner motor cooling fan. Replace the DC controller PCB.

A fault exists in the rotation of the following: laser scanner unit cooling fan, reader heat discharge fan 1, reader heat discharge fan 2. 0001 The laser scanner unit cooling fan has a fault. After the laser scanner unit cooling fan has gone on, the fan stop signal is detected for 5 sec or more. 0002 The reader heat discharge fan 1 has a fault. After the reader heat discharge fan 1 has gone on, the fan stop signal is detected for 5 sec or more. 0003 The reader heat discharge fan 2 has a fault. After the reader heat discharge fan 2 has gone on, the fan stop signal is detected for 5 sec or more. Disconnect and then connect J503 of the DC controller PCB. Replace the laser scanner unit cooling fan. Replace the DC controller PCB. Connect and then disconnect J512 of the DC controller PCB. Replace the reader heat discharge fan 1. Replace the DC controller PCB. Disconnect and then connect J521 of the DC controller PCB. Replace the reader heat discharge fan 2. Replace the DC controller PCB.

E197 E202

The laser scanner motor communication has a fault. 0000 The communication with the laser control IC is not normal. The scanner HP detection mechanism has a fault. 0001 While HP positioning is under way, the forward trip fails. 0002 While HP positioning is under way, the reverse trip fails. Disconnect and then connect the connector of the scanner HP sensor. Replace the scanner HP sensor. Replace the scanner motor. Replace the reader controller PCB. Replace the laser scanner unit. Replace the video PCB.

E225

The intensity of the scanning lamp is inadequate. (The lamp is exhausted.) Disconnect and then connect the connector of the scanning ** 0002 In ADF mode, the intensity of light is below the standard level between sheets. lamp. Replace the scanning lamp. Replace the inverter PCB. Replace the reader controller PCB. 0001 At time of shading, the intensity of light is below the standard level.

E227

The reader unit power supply (24 V) has a fault. 0001 At power-on, the 24V port is off. 0002 At the start of a job, the 24V port is off. 0003 At the end of a job, the 24V port is off. 0004 While a load is driven, the 24V port is off. Disconnect and then connect the reader power supply connector. Replace the power supply.

E240 **

A fault exists in the communication between the main controller and the DC controller. 0000 A fault has occurred in the communication between the CPUs of the main controller and the DC controller. Disconnect and then connect the connector. Replace the DC controller PCB. Replace the main controller PCB. Replace the main controller PCB. Replace the reader controller PCB.

E248

A fault exists in the following: main controller SRAM, reader controller EEPROM. 0000 At start-up, an SRAM check error has occurred. 0001 An error has occurred at time of power-on (EEPROM). 0002 An error has occurred during write operation (EEPROM). 0003 A read error has occurred after write operation (EEPROM).

E251

The inverter cooling fan rotation is faulty. 0000 After the inverter cooling fan has gone on, the fan stop signal is detected for 5 Disconnect and then connect J1110 of the reader controller sec or more. PCB. Replace the inverter cooling fan. Replace the reader controller PCB.

E302

Shading operation is faulty. 0000 In the course of shading operation, the processing doses not end within the reader controller. Disconnect and then connect J1107 and J1108 of the reader controller PCB. Replace the reader controller PCB. Replace the main controller PCB. Replace the DDR-SDRAM. Replace the HDD. Replace the main controller PCB. Replace the main controller PCB. Replace the open I/F relay PCB (relay PCB between the main controller and PS controller). Turn off and then back on he power. Replace the main controller PCB.

E315

The image data codec has a fault. 0007 A JBIG encoder error has occurred. 000d A JBIG decoding error has occurred. 000e An error has occurred in the course of software decoding. 0100 An overrun error has occurred. 0200 the open I/F relay PCB has detected an error (no recovery after a retry).

0300 Cubic time-out 0400 Shift Device A time-out 0401 Shift Device B time-out E351 E400 ** An error has occurred in the main controller communication. 0000 At start-up, a main controller communication error has occurred. An ADF communication error has occurred. 0001 A check sum error has occurred. 0002 A reception status error has occurred. 0003 A reception interrupt error has occurred. E402 * The ADF belt motor rotation is faulty.

Replace the main controller PCB. Disconnect and then connect the connector. Replace the reader controller PCB. Replace the ADF controller PCB.

40

Chapter 3
Code Description Remedial action

*: model equipped with DADF-Q1 (outside Japan, iR7105/7095; inside Japan: iR7105/7095/7086). **: model equipped with DADF-M1 (outside Japan: iR7086). 0000 While the belt motor drive signal is on, no lock signal occurs for 100 msec. Disconnect and then connect the cable between the belt motor driver PCB and the ADF controller PCB. Replace the belt motor clock sensor. Replace the belt motor clock sensor. Replace the belt motor. Replace the belt motor driver PCB. Replace the ADF controller PCB. Replace the delivery motor. Replace the delivery motor clock sensor. Replace the ADF controller PCB.

E404 *

The ADF delivery motor rotation is faulty. 0000 When the delivery motor drive signal is on, no clock signal occurs for 200 msec.

E405 *

The ADF separation motor rotation is faulty. 0000 When the separation motor drive signal is on, no clock signal occurs for 200 Replace the separation motor. Replace the separation motor msec. clock sensor. Replace the ADF controller PCB.

E410 *

The ADF pickup motor rotation is faulty. 0000 No signal occurs from the following sensors within 2 sec after the pickup motor is driven: - pickup roller height sensor 1 (PI8), pickup roller height sensor 2 (PI9) - pickup roller HP sensor (PI7) Replace the pickup motor. Replace the pickup roller height sensor (PI8). Replace the pickup roller height sensor 2 (PI9). Replace the pickup roller HP sensor (PI7). Replace the ADF controller PCB. Disconnect and then connect the connector. Replace the shift motor HP sensor. Replace the shift motor.

E413 **

The ADF shift motor rotation is faulty. 0001 The shift motor HP sensor is open. 0002 Shift motor HP sensor is closed.

E420 *

An ADF EEPROM read error has occurred. 0000 At power-on, an attempt to read the EEPROM backup data fails. Or, data that Replace the ADF controller PCB. has been read has a fault.

E490 E602 E604 E609

The ADF is of the wrong type. 0001 The ADF is of the wrong type. The HDD has an error. The time memory (DDR-SDRAM) is faulty or inadequate. 0000 A DDR-SDRAM (1 GB) of adequate capacity is not detected. The HDD temperature is abnormally low. 0008 At start-up, the HDD does not reach a specific temperature within a specific time. 0009 When returning from sleep mode, the HDD does not reach a specific temperature within a specific time. Replace the HDD. Replace the DDR-SDRAM. Replace the ADF. See the description under E602.

E610

The HDD encryption key is faulty. 0001 The memory is missing. 0002 The memory is inadequate. 0101 An attempt to initialize the key storage area of the memory has failed. Install the security board. Replace the DDR-SDRAM with one for the model in question (1 GB). Turn off and then on the power. Replace the main controller PCB.

0102 An error has occurred while the encryption processing area is being initialized. Turn off and then on the power. Replace the security board. 0201 An error has occurred in the encryption processing area. 0202 An error has occurred in the encryption processing area. 0301 An attempt to create an encryption key has failed. 0302 A fault exists in the encryption key. 0303 A fault exists in the encryption key. 0401 An error has been detected during coding. 0402 A fault has been detected in decoding. 0501 An error exists in the file management information in the image storage area. E711 An error has occurred in the communication between the pickup/delivery accessory and the printer unit. 0001 The communication controller has detected a fault. Turn off and then back on the power. (Turn off the machine and its delivery accessories; then, turn back on all accessories and then the machine.) Connect the communication cables and terminals between the machine and the delivery accessories once again. Replace the accessories controller PCB. Replace the transceiver PCB. Disconnect and then connect the connectors between the reader unit and the ADF. Replace the reader controller PCB. Replace the ADF controller PCB. Turn off and then on the power. Replace the main controller PCB. Turn off and then on the power. Replace the security board.

E712

An error exists in the communication between the ADF and the reader unit. 0001 As much as 5 sec or more has passed without recovery after communication stopped between the reader controller and the ADF controller.

E717

An error exists in the communication with the NE controller. After correcting the fault, be sure to reset the error. (COPIER>FUNCTION>CLEAR>ERR) 0001 The NE controller that has been connected before power-off is not recognized Disconnect and then connect the main controller PCB. Install at power-on. the NE controller. Replace the NE controller. 0002 An error that cannot be reset (e.g., cable break) has been detected in the communication.

41

Chapter 3
Code Description Remedial action

*: model equipped with DADF-Q1 (outside Japan, iR7105/7095; inside Japan: iR7105/7095/7086). **: model equipped with DADF-M1 (outside Japan: iR7086). E719 An error has occurred in the communication with the coin vendor/card reader. After correcting the fault, be sure to reset the error. (COPIER>FUNCTION>CLEAR>ERR) 0001 The coin vendor that was connected before power-off is not recognized at power-on. Disconnect and then connect the connector of the main controller PCB. Install the coin 0002 In the communication with the coin vendor, an error that cannot be reset has vendor. Replace the coin vendor. occurred (e.g., cable break). 0003 In the communication with the coin vendor, a communication error has occurred during acquisition of unit price information. 0011 The card reader that was connected before power-off is not recognized at power-on. 0012 In the communication with the card reader, an error that cannot be reset has occurred (e.g., cable break). E730 A PDL-related error has occurred. 1001 An initialization error has occurred at the start of a job. 100A An error has occurred in the communication with an external controller. 9004 A fault has been detected in the cable connection with an external controller. Turn off and then on the power. Replace the external 9005 A fault has been detected in the cable connection with an external controller. controller relay PCB. Replace the external controller. A006 The PDL mechanism does not respond. Reset the PDL mechanism. Turn off and then on the power. Reinstall the system software. Replace the main controller. Reset the PDL mechanism. Turn off and then on the power. Execute full formatting of the HDD, and reinstall the system software. Turn off and then on the power. Reinstall the system software. Execute full formatting of the HDD, and reinstall the system software. Reset the PDL mechanism. Turn off and then on the power. Disconnect and then connect the connector of the main controller PCB. Install the card reader. Replace the card reader.

A007 At start-up, the version of the machine control software and that of the PDL control software do not match. B013 The font data is corrupted at start-up.

E732

An error has occurred in the communication between the reader unit and the main controller. 0001 An error has occurred in the communication between the reader unit and the Disconnect and connect the connectors of the read main communication cable. Check the controller. power supply of the reader unit (to see if initialization occurs at power-on). Replace the 0010 A fault has been detected in the reader sync signal detection mechanism. reader controller PCB. Reap the reader I/F PCB. Replace the main controller PCB.

E733

An error has occurred in the communication between the reader unit and the main controller. 0000 An error has occurred in the communication between the reader unit and the Disconnect and then connect the connector. Check the power main supply of the DC controller (to controller. see if initialization occurs at time of start-up). Replace the DC controller PCB. Replace the 0001 An attempt to communicate with the DC controller fails. main controller PCB. 0010 A fault has occurred in the printer engine sync signal detection mechanism.

E740 E743

An error exists in the LAN controller. 0002 An illegal MAC address has been detected at start-up. Replace the main controller PCB. A fault exists in the communication between the main controller and the reader controller. 0000 The reader controller has detected an error in the communication between the Disconnect and then connect the connectors of the reader main communications cable. Replace controller and the reader controller. the reader controller PCB. Replace the main controller PCB.

E744

An error exists in the language file/boot ROM. 0001 The version of the language file on the HDD and that of bootable do not match. 0002 The language file on the HDD is too large. 0003 There is no language to which a switchover is made as described in the Config file on the HDD. 0004 An attempt to switch over to the language described in the Config file on the HDD fails. 1000 The connected boot ROM is not one designed for the model in question. 2000 An illegal engine ID has been detected. Replace the boot ROM. Reinstall the system software. Update the version of the language file (Language), or install the appropriate file.

E746 E749

An unsupported optional board has been detected. 0003 The option board that has been detected is one deigned for a different model. Replace it with one for the model in question. Restart in accordance with a change of the product configuration 0001 A boot ROM designed for a different model has been fitted in place (as when There is no need for remedial action. Nevertheless, the fact installing will remain as part of the an PDL option). error history.

E800

The auto power-off circuit has an error. An open circuit has been detected for 3 sec or more in the auto power-off circuit. Turn off and then on the power. Disconnect and then connect J505 of the DC controller PCB. Disconnect and then connect J1719 of the relay PCB. Replace the relay PCB. Replace the DC controller PCB.

42

Chapter 3
Code Description Remedial action

*: model equipped with DADF-Q1 (outside Japan, iR7105/7095; inside Japan: iR7105/7095/7086). **: model equipped with DADF-M1 (outside Japan: iR7086). E804 The rotation of the following is faulty: power supply cooling fan 1, power supply cooling fan 2, controller cooling fan. 0001 The fan stop signal has been detected for 5 sec or more after the power supply Disconnect and then connect J505 of the DC controller PCB. cooling fan 1 Replace the power supply has gone on. cooling fan 1. Replace the DC controller PCB. 0002 The fan stop signal has been detected for 5 sec or more after the power supply Disconnect and then connect J505 of the DC controller PCB. cooling fan 2 Replace the power supply has gone on. cooling fan 2. Replace the DC controller PCB. 0004 The fan stop signal of the controller cooling fan has been detected continuously for 16 sec. E805 The fixing heat discharge fan rotation is faulty. 0002 The fan stop signal has been detected for 5 sec or more after the fixing heat discharge fan has gone on. E820 The drum fan rotation is faulty. 0000 The fan stop signal has been detected for 5 sec or more after the drum fan has Disconnect and then connect J512 of the DC controller PCB. gone on. Replace the drum fan. Replace the DC controller PCB. E823 The pre-transfer charging assembly fan rotation is faulty. 0000 The fan stop signal has been detected for 5 sec or more after the pre-transfer Disconnect and then connect J504 of the DC controller PCB. charging Replace the pre-transfer assembly fan has gone on. charging assembly fan. Replace the DC controller PCB. E840 An HP detection error has occurred in relation to the fixing inlet sensor (fixing wrap jam detection). 0000 The home position is not detected when he sensor is moved up/down (i.e., the Disconnect and then connect J508, J552, and J553 of the DC sensor controller PCB. Disconnect has not gone on). and then connect J4001 and J4002 of the fixing inlet sensor 0001 The home position is not detected when the sensor is moved up/down (i.e., the ascent/descent motor driver PCB; as necessary, replace the fixing inlet sensor ascent/ sensor descent motor. Replace the fixing has not gone off). inlet sensor ascent/descent motor driver PCB. E850 There is a fault in the double-feeding detection unit. 0000 The double-feeding sensor (reception) fails to attain an ultrasonic signal of a Remove paper lint form the surface of the double-feeding specific sensor (reception). Remount the level. double-feeding sensor (transmission, reception). Disconnect and then connect J509 and J550 of the DC controller PCB. Replace the double-feeding sensor (transmission, reception). Replace the double-feeding sensor PCB (transmission, reception). Disconnect and then connect J503 of the DC controller PCB. Replace the fixing heat discharge fan. Replace the DC controller PCB. Disconnect and then connect J1028 of the main controller PCB. Replace the controller cooling fan. Replace the main controller PCB.

3.1.2 Detail in E602

iR7105 / iR7095 / iR7086 / <E602-XXYY> XX= "00"
XX YY 01 There is no system software for the main CPU. At time of start-up, no start-up partition (BOOTDEV) is found. Description The HDD cannot be recognized. T-3-2 Action to take - Turn off the power, and check the HDD cable. Thereafter, turn off the power. - Turn on the power, and listen for a sound from the HDD or touch the HDD, to see if the HDD is rotating. - Replace the HDD, and reinstall the system software. - Replace the main controller PCB. - Start up in safe mode, and perform full formatting using the SST and reinstall the system software; then, turn off and then on the power. - Replace the HDD, and reinstall the system software.
0011-1102

02

00

03

An interrupt has been detected while Take action according to the type of error code screen: data is being written to the boot <error code screen is black-and-white> device. - Turn off the power, and turn on the power while holding down the 1 and 9 keys. In response, the machine will automatically start to repair the sector in which the write operation has been interrupted. (The screen changes to solid black.) While repairs are being made, the progress of processing will be indicated on the screen, turning white at its end. When done, turn off and then back on the power. - Start up in safe mode, and perform full formatting using the SST and reinstall the system software; then, turn off and the back on the power. - Replace the HDD, and reinstall the system software. <error core screen is normal (spanner mark)> - Set CHK-TYPE=0, and execute HD-CHECK; then, turn off and then back on the power. - Start up in safe mode, and execute full formatting using the SST and reinstall the system software; then, turn off and back on the power. - Replace the HDD, and reinstall the system software. No system software is found for the - Start up in safe mode, and perform full formatting using the SST and reinstall the system software; then, turn sub CPU. off and then back on the power. - Replace the HDD, and reinstall the system software. A file used by the Web browser to make references is damaged, or has been deleted. - Reinstall the content of the Web browser. - Replace the HDD, and reinstall the system software.

06

12

43

Chapter 3 XX= "01" to "FF"

XX CHKTYPE Occurrence at time of start-up Partition Description 03 05 Action 01 02 03 04 05 06 07 08 09 10 11 12 13 FF 3 4 5 6 7 8 0 YY *1 2 1 FSTDEV IMG_MNG FSTCDEV APL_GEN TMP_GEN TMP_FAX TMP_PSS PDLDEV BOOTDEV APL_MEAP APL_SEND APL_KEEP APL_LOG not specified compressed image data (e.g., Box) file management table, profile job archiving (changing) general-purpose data general-purpose data (temporary file) not used for PDL spool (temporary file) PDL-related file firmware (system, MEAP, key, certificate, PDF dictionary, RUI, content, voice dictionary) MEAP application address book, filter for non-initialization data storage system log check for and recovery of HDD full-fault sectors *3 *1 *2 *3 *1 *4 Action - Set the partition number in question for CHK-TYPE, and execute HD-CLEAR; then, turn off and then back on the power. - Enter CHK-TYPE in question (for the partition), and execute HD-CLEAR; then, turn off and then back on the power. - Ask the user to download the address book data using a remote UI. - Set the partition number in question for CHK-TYPE, and execute HD-CLEAR; then, turn off and then back on the power. - Start download mode, and perform full formatting using the SST and reinstall the system software; then turn off and then back on the power. The recovery operation for the boot partition is not possible without the use of the SST in save mode. - Set CHK-TYPE=0, and execute HD-CHECK; then, turn off and then back on the power. - Start download mode, and perform full formatting using the SST and reinstall the system software; then, turn off and then back on the power. - Set CHK-TYPE=0, and execute HD-CHECK; then, turn off and then back on the power. - Set CHK-TYPE=1, 2, 3, 5, and execute HD-CLEAR; then, turn off and then back on the power. - Enter CHK-TYPE in question (for the partition), and execute HD-CLEAR; then, turn off and then back on the power. - Replace the HDD, and reinstall the system software. The machine is designed so that execution of HD-CLEAR is not possible in service mode (so as to prevent loss of information, e.g., address book, filter information). - Ask the user to download the address book data using a remote UI. - In service mode, start download mode, and execute full formatting using the SST and reinstall the system A file system error has occurred. software; then, turn off and then back on the power. - Set CHK-TYPE=1, 2, 3, 5, and execute HD-CLEAR; then, turn off and then back on the power. - Replace the HDD, and reinstall the system software. The recovery operation for the boot partition is not possible without the use of the SST in save mode. - Start up in safe mode, and execute full formatting using the SST and reinstall the system software; then, turn off and back on the power. - Replace the HDD, and reinstall the system software. 00 01 02 04 11 21 The HDD has poor contact, or a system error has occurred. The HDD has poor contact. - Check the cable and the power cord. - Start up in safe mode, and execute full formatting using the SST and reinstall the system software; then, turn off and back on the power. - Replace the HDD, and reinstall the system software. - Check the cable and the power cord. - Replace the HDD, and reinstall the system software. *8 *5 *6 *8 *5 *7 *9 *10 *11 *12 *1 *5 T-3-3 YY Occurrence during normal execution 13,25 Action 10,12,14, 22,23,24

XX

00,01,0 11,21 2,04

Description

*2 03

The ongoing write operation is interrupted (at start-up).

*3

*4 *5

*6 05 *7

*8

*9

*10

*11

13 25

There is a strong possibility of damage in the file data (e.g., Box) stored on the HDD. - Set the partition number in question for CHK-TYPE, and execute HD-CHECK; then, turn off and back on the power. The ongoing write operation has - Set the partition number in question for CHK-TYPE, and execute HD-CLEAR; then, turn off and back on been interrupted. the power. (In the case of BOOTDEV, BOOTDEV2 or APL_SEND, execute reformatting using the SST, and reinstall the system software.) - Replace the HDD, and reinstall the system software. - Start up in safe mode, and perform full formatting using the SST and reinstall the system software; then, turn off and back on the power. - Replace the HDD, and reinstall the system software.

*12

10 12 14 22 23 24

A system error or a packet error has been detected.

44

Chapter 3

3.2 Jam Code

3.2.1 Jam Code (printer)
iR7105 / iR7095 / iR7086 /
T-3-4 Code 01xx 02xx 0Axx 0Bxx 0C00 Code xx01 xx02 xx03 xx04 xx05 xx06 xx07 xx08 xx09 xx0A xx0B xx0C xx0D Jam type delay jam stationary jam power-on residual jam door open jam double-feeding Sensor type right deck pickup sensor left deck pickup sensor cassette 3 pickup sensor cassette 4 pickup sensor vertical path 1 paper sensor vertical path 2 paper sensor vertical path 3 paper sensor vertical path 4 paper sensor registration roller sensor fixing claw jam sensor inside delivery sensor outside delivery sensor fixing feed unit outlet sensor double-feeding sensor (reception) Sensor No. PS20 PS25 PS37 PS42 PS47 PS49 PS41 PS46 PS5 PS65 PS9 PS10 PS11 Code xx0F xx10 xx11 xx12 xx13 xx14 xx15 xx16 xx17 xx18 xx19 xx1A Sensor type duplexing reversal sensor duplexing outlet sensor pre-confluence sensor post-confluence sensor left deck feed sensor right deck feed sensor side paper deck feed sensor multifeeder curl-removal sensor side paper deck pickup sensor image write start sensor manual feeder feed sensor fixing inlet sensor PS65 Sensor No. PS12 PS61 PS14 PS15 PS26 PS27 PS106 PS68 PS101 PS60 PS35 PS63 Sensor type See the table Sensor No.
0011-5508

3.2.2 Jam Code (DADF-Q1)

iR7105 / iR7095 /
T-3-5 Code 0001 0002 0003 0004 0005 0006 0007 0008 0009 0010 0011 0012 0013 0014 0015 Sensor type separation delay pickup delay pickup stationary 1 pickup stationary 2 reversal delay reversal stationary delivery delay delivery stationary 1 delivery stationary 2 pre-reversal delay 1 pre-reversal delay 2 pre-reversal delay 3 pre-reversal stationary 1 pre-reversal stationary 2 pre-reversal stationary 3 Sensor No. S4 S4,S2 S3 S2 S1 S1 PI13 PI13,S9 PI13,S9 S3 S1,S3 PI4 S1,S4 S2,S4 S2,S3 Description At time of separation, the separation sensor does not detect the original after it has been moved a specific distance (221 mm) following the start of the separation motor. At time of separation, the pre-registration roller sensor does not detect the original after it has been moved a specific distance (93 mm) following the detection of its lead edge by the separation sensor. At time of pickup, the post-registration sensor does not detect the original after it has been moved a specific distance (40 mm) following the start of the reversal motor. At time of pickup, the pre-registration roller sensor detects the original after it has been moved a specific distance (330 mm if small; 660 mm if large) following the start of the reversal motor. At time of reversal, the reversal sensor does not detect the original after it has been moved a specific distance (104 mm) from the platen roller. At time of reversal, the reversal sensor detects the original after it has been moved a specific distance (original length x 1.5 mm) following arching operation. At time of delivery, the delivery sensor does not detect the original after it has been moved a specific distance (631 mm - original length) following the start of the belt motor. At time of delivery, the manual feeder registration roller sensor detects the original after it has been moved a specific distance (original length + 100 mm) following the activation of the delivery sensor. At time of delivery, the delivery sensor detects the original after it has been moved a specific distance (original length + 100 mm) following the deactivation of the manual feeder registration roller sensor. At time of pre-reversal, the post-registration roller sensor does not detect the original after it has been moved a specific distance (50 mm) following the activation of the reversal motor. At time of pre-reversal, the reversal sensor does not detect the original after it has been moved a specific distance (100 mm) after the post-registration roller sensor has gone on. At time of pre-reversal, the reversal sensor does not detect the original when it has been moved over a specific distance (100 mm) after the reversal motor has stopped. At time of reversal, the separation sensor has detected the original when it has been moved over a specific distance (169 mm) after the reversal sensor has gone on. At time of pre-reversal, the pre-registration sensor has detected the original when it has been moved over a specific distance (120 mm) after its trail edge has moved past the separation pull-off roller. At time of pre-reversal, the post-registration roller sensor detects the original after it has been moved a specific distance (50 mm) following the passage of the trail edge of the original for the pre-registration roller sensor. At time of pre-reversal, the reversal sensor detects the original after it has been moved a specific distance (100 mm) following the passage of the trail edge of the original from the pre-registration roller sensor. At time of pre-reversal pickup, the reversal sensor does not detect the original after it has been moved a specific distance (100 mm) following the start of the reversal sensor. At time of pre-reveal, the pre-reversal sensor has detected the original when it has been moved over a specific distance after the reversal sensor has detected its lead edge.
0011-5512

0016 0017 0018

pre-reversal stationary 4 pre-reversal pickup delay pre-reversal pickup stationary 1

S1,S3 S1 S1,PI4

45

Chapter 3
Code 0019 0020 0021 0022 0023 0024 0025 Sensor type pre-reversal pickup stationary 2 reversal pickup delay reversal pickup stationary pickup lead edge skew pickup trail edge skew pickup fault 1 pickup fault 2 Sensor No. S1,PI4 S2 S2 S4,S5 S4,S5 S1 S3,S2 Description At time of pre-reversal pickup, the reversal sensor detects the original after it has been moved a specific distance following the detection of its trail edge by the pre-reversal sensor. At time of reversal, the pre-registration roller sensor does not detect the original after it has been moved a specific distance (197 mm) following the end of arching operation. At time of reversal, the pre-registration roller sensor detects the original after it has been moved a specific distance (original length X 1.5 mm) following the start of the pre-registration roller sensor. At time of separation, there is a discrepancy of an equivalent of 10 mm in the timing of detecting the lead edge between the separation sensor and the skew sensor. At time of pickup, there is a discrepancy of an equivalent of 10 mm in the timing of detecting the trail edge between the separation sensor and the skew sensor. At time of pickup, the reversal sensor detects an original before it moves past the pre-registration roller sensor. At time of pickup, the post-registration sensor detects an original before the start of the reversal motor. At time of pickup, the pre-registration roller sensor does not detect the original after it has been moved a specific distance. At time of pre-reversal, the pre-registration roller sensor detects an original before the start of the reversal motor. At time of reversal, the pre-registration roller sensor does not detect the original while its trail edge is moving past the reversal sensor. At time of pre-reversal, there is a discrepancy of an equivalent of 10 mm in the timing of detecting the trail edge between the separation sensor and the skew sensor. At time of reversal, the pre-reversal sensor detects the original during a wait for the activation of the preregistration roller sensor. At time of arching operation in manual feed mode, the manual feeder registration roller sensor does not detect an original within a specific period of time (1 sec) from the start of the delivery motor. At time of pickup from the manual feeder, the reversal sensor does not detect the original after it has been moved a specific distance (638 mm) following the start of the belt motor. At time of pickup from the manual feeder (platen roller), the reversal sensor does not detect the original after it has been moved a specific distance (50 mm) following the start of the belt motor. At time of manual feed delivery, the delivery sensor does not detect the original after it has been moved a specific distance (621 mm - original length). At time of manual feed delivery, the delivery sensor detects the original after it has been moved a specific distance (original length x 1.5) following the activation of the delivery sensor. The 1st sheet is identified as a pickup delivery 1 jam (0003). The 1st sheet is identified as a pickup stationary 2 jam (0004). The 1st sheet is identified as a reversal delay jam (0005). The 1st sheet is identified as a reversal stationary jam (0006). The 1st sheet is identified as a delivery delay jam (0007). The 1st sheet is identified as a delivery delay jam (0008). The 1st sheet is identified as a delivery stationary 2 jam (0009). The 1st sheet is identified as a pre-reversal delay 1 jam (0010). The 1st sheet is identified as a pre-reversal delay 2 jam (0011). The 1st sheet is identified as a pre-reversal delay 3 jam (0012). The 1st sheet is identified as a pre-reversal stationary 1 jam (0013). The 1st sheet is identified as a pre-reversal stationary 2 jam (0014). The 1st sheet is identified as a pre-reversal stationary 3 jam (0015). The 1st sheet is identified as a pre-reversal stationary 4 jam (0016). The 1st sheet is identified as a pre-reversal pickup delay jam (0017). The 1st sheet is identified as a pre-reversal pickup stationary 1 jam (0018). The 1st sheet is identified as a pre-reversal pickup stationary 2 jam (0019). The 1st sheet is identified as a reversal pickup delay (0020). The 1st sheet is identified as a reversal pickup stationary jam (0021). The 1st sheet is identified as a pickup lead edge skew jam (0022). The 1st sheet is identified as a pickup trail edge skew jam (0023). A pickup NG1 condition (0024) has occurred on the 1st sheet. A pickup NG1 condition (0025) has occurred on the 1st sheet. A reversal pickup trail edge skew condition (0026) has occurred on the 1st sheet. The 1st sheet is identified as a reversal pickup fault 1 jam (0027). The software control mechanism has failed. In copyboard mode, an original has been read and moved to and stopped at the right side of the platen roller; however, the preceding original has not been delayed.

0026 0027 0030 0031 0032 0033 0034 0043 0044 0045 0046 0047 0048 0049 0050 0051 0052 0053 0054 0055 0056 0057 0058 0059 0060 0061 0062 0063 0064 0065 0066 0067 0071 0072

reversal pickup trail edge skew reversal pickup fault 1 manual feed registration delay manual feed registration delay manual feeder reversal stationary manual feed delivery delay manual feed delivery stationary

S4,S5 PI4 S9 S1 S1 PI13 PI13

1st sheet pickup stationary 1 S3 1st sheet pickup stationary 2 S2 1st sheet reversal delay 1st sheet reversal stationary 1st sheet delivery delay 1st sheet delivery stationary 1 1st sheet delivery stationary 2 S1 S1 PI13 PI13,S9 PI13,S9

1st sheet pre-reversal delay 1 S3 1st sheet pre-reversal delay 2 S1,S3 1st sheet pre-reversal delay 3 PI4 1st sheet pre-reversal stationary 1 1st sheet pre-reversal stationary 2 1st sheet pre-reversal stationary 3 1st sheet pre-reversal stationary 4 S1,S4 S2,S4 S2,S3 S1,S3

1st sheet pre-reversal pickup S1 delay 1st sheet pre-reversal pickup S1,PI4 stationary 1 1st sheet pre-reversal pickup S1,PI4 stationary 2 1st sheet reversal pickup delay 1st sheet reversal pickup stationary 1st sheet pickup lead edge skew 1st sheet pickup trail edge skew 1st sheet pickup fault 1 1st sheet pickup fault 2 S2 S2 S4,S5 S4,S5 S1 S3,S2

1st sheet reversal pickup trail S4,S5 edge skew 1st sheet reversal pickup NG1 timing fault 1 timing fault 2 PI4 -

46

Chapter 3
Code 0073 0074 0075 0076 0077 0078 0079 0080 0081 0082 0083 0084 0085 0090 0091 0092 0093 0094 Sensor type illegal size manual feed original size error image lead edge position error 1st sheet image lead edge position error belt speed setting error belt speed switch-over error belt status error image lead edge output timing error reversal speed setting error reversal speed switch-over error reversal status error last original error error ADF open user DF open cover open user cover open initial stationary Sensor No. S3 S9,S1 S7 S7 PI1 PI1 PI1 S2,S3,SW301 PI5 PI5 PI5 PI1 PI1,PI2,PI11 PI10 PI10 PI3,PI6 PI3,PI6 Description At time of LDR stream reading, the post-registration sensor detects the original after it has been moved a specific distance (30 mm) from the wait position. At time of manual feed, the reversal sensor detects an original while the manual registration roller sensor also detects an original. At time of stream reading, no change has occurred in the read position in response to a request for a change. The 1st sheet is identified as having an image lead edge position error (0075). The speed setting of the belt motor is below the minimum speed (100 mm/sec) or above the maximum speed (700 mm/sec). When the belt motor speed is switched over, the belt motor is not moving at a constant speed. At time of switch-over, the state is not any of the following: acceleration, constant speed rotation, deceleration. At time of stream reading, the image lead edge signal is generated in the course of acceleration while a move is made from the wait position to the image lead edge position. The speed setting of the reversal motor is below the minimum speed (100 mm/sec) or above the maximum speed (700 mm/sec). At time of switching over the reversal motor speed, the reversal motor is not rotating at a constant speed. At time of switch-over, the state of the reversal motor is not any of the following: acceleration, constant speed, deceleration. A belt motor error occurs while the last original is being discharged by the platen roller or being moved. A motor error other than an IPC communication or pickup error has occurred. (less than 3 times) The ADF is identified as being open. The ADF is identified as being open while the machine is operating. The cover is identified as being open. The cover (front or rear) is identified as being open while the machine is operating.

PI4,PI12,PI13,S At the start of operation, a sensor inside the paper path detects an original. 1,S2,S3,S4,S5,S 9 S6 S1 S1,S9 The pickup signal has been received for a specific period of time (2 sec) in the absence of a detected original. The reversal sensor detects an original while the belt motor is moved for a specific distance before the start of a left pickup job. At time of manual feed pickup, the reversal sensor detects an original while the manual feeder registration roller sensor also detects an original. A drop occurs in the voltage supplied by the host machine while the machine is operating.

0095 0096 0097 0098

cycle fault residual original manual feeder residual original power-down

3.2.3 Jam Code (DADF-M1)

iR7086
T-3-6 Code 0001 0002 Sensor post-separation sensor post-separation sensor Notation PI7 PI7 Description The post-separation sensor does not detect paper when paper has been moved 452 mm after the start of separation. - The separation sensor detects paper when paper has been moved 500 mm (if extralength, +200 mm) -45.5 mm after registration pickup. - the sensor goes on (paper with hole) before paper has been fed 12 mm after the detection of the trailing edge; the separation sensor detects paper after paper has been fed 50 mm from when the separation senor has gone on. The registration sensor does not detect paper a feed length of 134.8 mm after the postseparation sensor has gone on. The read sensor goes off before the registration sensor goes off. - The read sensor does not detect paper a feed length of 364.2 mm (182.1 x 2) from the point of registration. - The read sensor does not detect paper a feed length of 157.4 mm (78.7 x 2) from the point of No. 2 registration. - The read sensor detects paper a feed length of 500 mm (if extra-length, +200 mm) after the start of feed, resumed after a temporary stop for reading. - At time of LTRR/LGL identification in mix mode, the read sensor detects paper a feed length of 514 mm after the start of feed from the edging wait point. If not in high-speed duplexing mode, the delivery sensor does not detect paper when paper is moved 132.1 mm after it has reached the leading edge lower stream roller with reference to the activation of the read sensor. The delivery sensor detects paper a feed length of 161.9 mm after the trailing edge read end point. 1st sheet, post-separation sensor, stationary 1st sheet, registration sensor, non arrival 1st sheet, registration sensor, stationary 1st sheet, read sensor, non arrival 1st sheet, read sensor, stationary 1st sheet, delivery sensor, non arrival 1st sheet, delivery sensor, stationary fault in software timing
0011-5509

0003 0004 0005

registration sensor registration sensor read sensor

PI1 PI1 PI8

0006

read sensor

PI8

0007

delivery reversal sensor

PI9

0008 0042 0043 0044 0045 0046 0047 0048 0071

delivery reversal sensor post-separation sensor registration sensor registration sensor read sensor read sensor delivery reversal sensor delivery reversal sensor TIMING NG

PI9 PI7 PI1 PI1 PI8 PI8 PI9 PI9 -

47

Chapter 3
Code 0073 0090 0091 0092 0093 0094 0095 Sensor TIMING NG ADF open/closed sensor 1 ADF open/closed sensor 1 DF cover open/closed sensor DF cover open/closed sensor registration sensor, separation sensor, feed sensor, delivery reversal sensor original set sensor, DF cover open/closed sensor, ADF open/closed sensor 1 Notation PS502 PS502 PI6 PI6 PI1, PI7, PI8, PI9 Description fault in shift motor The ADF has been opened while in operation. The ADF has been opened while in operating (paper wait). The cover has been opened while in operation (drive system in operation). The cover has been opened while in operation (paper wait). Paper has been detected in the path while the 1st sheet is being picked up.

PI5, PI6, PS502 With no paper in the tray or while the tray is open, the start of pickup operation is detected.

48

Chapter 3

3.2.4 Jam Code (finisher)

iR7105 / iR7095 / iR7086 /
T-3-7 Code 1002 1004 1006 1008 100A 100C 100E 1042 1044 1046 104A 1054 1103 1105 1107 1109 110B 110D 110F 1143 1145 1147 114B 1155 1320 1422 1550 1721 1F52 Jam Inlet sensor delay Shift unit sensor delay Buffer path 1 sensor delay Buffer path 2 sensor delay Upper delivery sensor delay Lower path sensor delay Lower delivery sensor delay Saddle inlet sensor delay Saddle small sensor delay Saddle vertical path sensor delay Saddle pre-pressing sensor delay Saddle pressing home position sensor delay Inlet sensor stationary Shift unit sensor stationary Buffer path 1 sensor stationary Buffer path 2 sensor stationary Upper delivery sensor stationary Lower path sensor stationary Lower delivery sensor stationary Saddle inlet sensor stationary Saddle small sensor stationary Saddle vertical path sensor stationary Saddle pre-pressing sensor stationary Sensor PS3 PS4 UN13 UN14 PS5 UN24 PS6 PS101 PS103 PS105 PS111 PS113 PS3 PS4 UN13 UN14 PS5 UN24 PS6 PS101 PS103 PS105 PS111 Description The inlet sensor (PS3) does not detect paper within a specific period of time (distance) after the delivery signal from the host machine has been received. The shift unit sensor (PS4) does not detect paper within a specific period of time (distance) after the inlet sensor (PS3) has detected paper. The buffer path 1 sensor (UN13) does not detect paper within a specific period of time (distance) after the shift unit sensor (PS4) has detected paper. The buffer path 2 sensor (UN14) does not detect paper within a specific period of time (distance) after the shift unit sensor (PS4) has detected paper. The upper delivery sensor (PS5) does not detect paper within a specific period of time (distance) after the buffer path 2 sensor (UN14) has detected paper. The lower path sensor (UN24) does not detect paper within a specific period of time (distance) after the buffer path 2 sensor (UN14) has detected paper. The lower delivery sensor (PS6) does not detect paper within a specific period of time after the buffer path 2 sensor (UN14) has detected paper. The saddle inlet sensor (PS101) does not detect paper within a specific period of time (distance) after the lower path sensor (UN24) has detected paper. The saddle small sensor (PS103) does not detect paper within a specific period of time (distance) after the saddle inlet sensor (PS101) has detected paper. The paper does not detect the saddle vertical path sensor (PS105) within a specific period of time after the saddle stop plate operation has been ended. The saddle pre-pressing sensor (PS111) does not detect paper within a specific period of time after the saddle stop plate operation has been ended. The saddle pressing home position sensor (PS113) does not detect the home position within a specific period of time after the start of saddle stack delivery operation. The paper does not leave the inlet sensor (PS3) within a specific period of time after it has detected paper. The paper does not leave the shift unit sensor (PS4) within a specific period of time (distance) after the inlet sensor (PS3) has detected paper. The paper does not leave the buffer path 2 sensor (UN14) within a specific period of time (distance) after the shift unit sensor (PS4) has detected paper. The paper does not leave the buffer path 2 sensor (UN14) within a specific period of time (distance) after the shift unit sensor (PS4) has detected paper. The paper does not leave the upper delivery sensor (PS5) within a specific period of time (distance) after the buffer path 2 sensor (UN14) has detected paper. The paper does not leave the lower path sensor (UN24) within a specific period of time (distance) after the buffer path 2 sensor (UN14) has detected paper. The paper does not leave the lower delivery sensor (PS6) within a specific period of time (distance) after the buffer path 2 sensor (UN14) has detected paper. The paper does not leave the saddle inlet sensor (PS101) within a specific period of time (distance) after the lower path sensor (UN24) has detected paper. The paper does not leave the saddle small sensor (PS103) within a specific period of time (distance) after the saddle inlet sensor (PS101) has detected paper. The paper does not leave the saddle vertical path sensor (PS105) within a specific period of time after the saddle stop plate operation has been started. The paper does not leave the saddle pre-pressing sensor (PS111) within a specific period of time after the end of saddle stop plate operation. The saddle home position sensor (PS113) remains on (detects the home position) at the start of saddle pressing operation. Paper exists within the transport path at power-on. MSW1 SU The front cover switch (MSW1) has identified the front cover as being open during machine operation. The saddle stitcher unit does not detect the start-up of the stitcher motor (M110) within a specific period of time. Paper exists in the path during initial rotation of the host machine. PS110 The saddle stop plate sensor (PS110) does not detect the start-up of the saddle motor stop plate motor (M106) within a specific period of time.
0012-1381

Saddle pressing home position sensor stationary PS113 Residual (at power-on) Door open stitcher staple Residual (during initial rotation) Saddle stop plate

3.3 Alarm Code

3.3.1 Alarm Code
iR7105 / iR7095 / iR7086 /
T-3-8 EE 00 Location error code indication ffff 0804 Alarm system fan alarm (detail code: 0004)
0011-5558

49

Chapter 3
EE 02 Location reader unit (scanner system) ffff 0003 0004 0005 0006 0007 0008 0009 0010 0011 0012 0013 0014 0015 0016 0017 0018 0019 04 pickup/transport system 0001 0002 0003 0004 0007 0008 0011 0012 0013 0014 0017 0018 0019 0020 0021 0022 0023 0024 0025 0026 0027 0028 30 high-voltage system 0001 0002 0003 32 33 potential control system fan system 0001 0002 0001 0006 0007 61 62 65 stapler system (sorter/finisher) saddle stitcher system puncher system (sorter/finisher) 0001 0001 0001 Alarm dust detection small 1 dust detection small 2 dust detection small 3 dust detection small 4 dust detection small 5 dust detection small 6 dust detection small 7 dust detection large 1 dust detection large 2 dust detection large 3 dust detection large 4 dust detection large 5 dust detection large 6 dust detection large 7 small position stream read disable large position stream read disable scanner lamp intensity too low right deck lifter left deck lifter alarm cassette 3 lifter alarm cassette 4 lifter alarm manual feeder tray lifter alarm side paper deck lifter alarm right deck retry alarm left deck retry alarm cassette 3 retry alarm cassette 4 retry alarm manual feeder retry alarm side paper deck retry alarm right deck pickup sensor low intensity alarm left deck pickup sensor low intensity alarm cassette 3 pickup sensor low intensity alarm cassette 4 pickup sensor low intensity alarm right deck pull-off sensor low intensity alarm left deck pull-off sensor low intensity alarm cassette 3 pull-off sensor low intensity alarm cassette 4 pull-off sensor low intensity alarm side paper deck pickup sensor low intensity alarm side paper deck pull-off sensor low intensity alarm primary charging assembly leakage transfer charging assembly leakage separation charging assembly leakage potential control VD alarm potential control VL alarm delivery assembly curl-removing fan alarm developing assembly fan alarm delivery anti-adhesion fan alarm no staple no switch punch case full

50

Chapter 4

Chapter 4 User Mode Items

4.1 User Mode Items
4.1.1 Common Settings
iR7105 / iR7095 / iR7086 / *1 Indicates the default setting. *2 Indicates items that appear only when the appropriate optional equipment is attached. *3 Indicates information that is delivered only if the number of output trays in the host machine and client machines is the same.
T-4-1 Item Initial Function Settings Select Initial Function: Copy*1, Send, Mail Box, MEAP Set System Monitor as the Initial Function: On/Off*1 Set the default screen for System Monitor: Settings: Print Status*1, Consumables, Others (Copy*1, Send, Receive), Status*1, Log Auto Clear Setting Function Order Settings Initial Function*1/Selected Function Function Order Settings: Copy*1, Send*2, Mail Box, Scan, Printer*2 Settings for Function Group Order: Group A, Group B, MEAP Audible Tones Entry Tone: On*1, Off Invalid Entry Tone: On, Off*1 Restock Supplies Tone: On, Off*1 Error Tone: On*1, Off Job Done Tone: On*1, Off Forgot Original Tone (for the imageRUNNER 7086): On, Off*1 ON*1/OFF ON*1/OFF Copy, Printer, Mail Box, Receive, Other: (Stack Bypass: On/Off*1, All Other Paper Sources: On*1/Off) Copy: Consider Paper Type: On/Off*1 Register Paper Type Paper Drawers 1 and 2 and Paper Deck-W1 or Paper Deck-X1: Plain*1, Recycled, Color, Letterhead, Bond, 3-Hole Punch, Heavy Paper Drawers 3 and 4: Plain*1, Recycled, Color, Letterhead, Bond, 3-Hole Punch, Heavy, Tab Paper Energy Saver Mode Energy Consumption in Sleep Mode LTRR/STMT Original Selection Tray Designation*2*3 -10%*1/-25%/-50%/None Low*1/High Distinguish Manually, Use LTRR Format*1, Use STMT Format If the Optionl Finisher-V1 or Saddle Finisher-V2 Is Attached: Tray A: Copy*1, Mail Box*1, Printer*1, Receive*1, Other*1 Tray B: Copy*1, Mail Box*1, Printer*1, Receive*1, Other*1 If the Optional Finisher-V1 or Saddle Finisher-V2, and High Capacity Stacker A1 Are Attached: Tray A: Copy*1, Mail Box*1, Printer*1, Receive, Other Tray B: Copy*1, Mail Box*1, Printer*1, Receive, Other Tray C: Receive*1, Other*1 High Volume Stack Mode*2 Printing Priority ON/OFF*1 Copy: 1*1/2/3 Printer : 1/2*1/3 Mail Box, Receive, Other: 1/2/3*1 Register (Entire Image Composition*1, Transparent Image), Erase, Check Print, Details Register, Edit, Erase ON/OFF*1 Register/Edit, Erase, Register Name
0010-7412

Display Remaining Paper Message Inch Entry Drawer Eligibility For APS/ADS

Register Form for Form Composition Register Characters for Page No./Watermark Stack Bypass Standard Settings Registering Irregular Size for Stack Bypass

51