HCD-CPX11

SERVICE MANUAL

AEP Model
UK Model
Korean Model
Australian Model

Ver 1.1 2004.04

HCD-CPX11 is the Amplifier, CD player,

Tape Deck and Tuner section in CMTCPX11.

Model Name Using Similar Mechanism

CD

NEW

CD Mechanism Type

CDM80BH-F1BD81

Optical Pick-up Name

KSM-215DCP

Tape deck

Model Name Using Similar Mechanism

NEW

Section

Tape Transport Mechanism Name

CMAL1Z-236A

Section

SPECIFICATIONS
Amplifier section

CD player section

European model:

Laser

DIN power output (rated): 55 + 55 W

(4 ohms at 1 kHz, DIN)
Continuous RMS power output (reference):
75 + 75 W
(4 ohms at 1 kHz, 10%
THD)

Other models:
Semiconductor laser
(CD: =780 nm)
Emission duration:
continuous
CD: 2 Hz 20 kHz
780 790 nm

Frequency response
Wavelength

Tape deck section

Recording system
4-track 2-channel stereo
Frequency response
50 13,000 Hz (3 dB),
The following measured at 220 240 V AC, 50/60 Hz
using Sony TYPE I
DIN power output (rated): 55 + 55 W
cassettes
(4 ohms at 1 kHz, DIN)
Continuous RMS power output (reference):
Tuner section
75 + 75 W
FM stereo, FM/AM superheterodyne tuner
(4 ohms at 1 kHz, 10%
THD)
FM tuner section
Inputs
Tuning range
87.5 108.0 MHz (50 kHz
MD/VIDEO IN (phono jacks):
step)
Sensitivity 450/250 mV,
Antenna
FM wire antenna
impedance 47 kilohms
Antenna terminals
75 ohms unbalanced
Outputs
Intermediate frequency
10.7 MHz
CD DIGITAL OUT:
Optical Wavelength:
AM tuner section
660 nm
Tuning range
PHONES:
accepts headphones with
European model:
531 1,602 kHz
an impedance of 8 ohms or
(with the tuning interval
more
set at 9 kHz)
SPEAKER:
accepts impedance of 4 ohms

Other models:

Antenna
Intermediate frequency

530 1,710 kHz

(with the tuning interval
set at 10 kHz)
531 1,602 kHz
(with the tuning interval
set at 9 kHz)
AM loop antenna, external
antenna terminal
450 kHz

General
Power requirements
European model:
Korean model:
Australian model:
Power consumption
European model:

230 V AC, 50/60 Hz

220 V AC, 60 Hz
230 240 V AC, 50/60 Hz

50 W
0.3 W (in Power Saving
mode)
Korean model:
50 W
Other models:
50 W
Dimensions (w/h/d) incl. projecting parts and controls
Approx. 175 240.5 291
mm
Mass
Approx. 4.3 kg
Design and specifications are subject to change
without notice.

MICRO HI-FI COMPONENT SYSTEM

9-877-766-02
2004D16-1
2004.04

Sony Corporation
Home Audio Company
Published by Sony Engineering Corporation

HCD-CPX11

Notes on chip component replacement

Never reuse a disconnected chip component.
Notice that the minus side of a tantalum capacitor may be
damaged by heat.
Flexible Circuit Board Repairing
Keep the temperature of the soldering iron around 270 C
during repairing.
Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
Be careful not to apply force on the conductor when soldering
or unsoldering.

CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous radiation
exposure.

This appliance is
classified as a CLASS 1
LASER product. This
label is located on the
rear exterior.

NOTES ON HANDLING THE OPTICAL PICK-UP

BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pickup block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
MODEL IDENTIFICATION
Back Panel

UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
Part No.

: LEAD FREE MARK

Unleaded solder has the following characteristics.
Unleaded solder melts at a temperature about 40 C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
Strong viscosity
Unleaded solder is more viscou-s (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.

SAFETY-RELATED COMPONENT WARNING!!

COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.

Model Name
AEP and UK models
Korean model
Australian model

Part No.
4-252-358-0[]
4-252-358-2[]
4-252-358-3[]

HCD-CPX11

TABLE OF CONTENTS
1.

SERVICING NOTES ................................................ 4

2.

GENERAL ................................................................... 9

3.

DISASSEMBLY

3-1.
3-2.
3-3.
3-4.
3-5.
3-6.
3-7.
3-8.
3-9.
3-10.
3-11.
3-12.
3-13.
3-14.
3-15.
3-16.
3-17.

Cover ...............................................................................
Front Panel Section .........................................................
TC Board, Mechanical Deck ..........................................
PANEL Board ..................................................................
MAIN Board, PRE AMP Board ......................................
CD Mechanism Deck (CDM80BH-F1BD81) .................
Chassis (Top) ...................................................................
Lever (Loading R/L) ........................................................
Disc Stop Lever, Disc Sensor Lever ................................
DRIVER Board ...............................................................
BD81A Board ..................................................................
BU Section ......................................................................
Optical Pick-up (KSM-215DCP) ....................................
Lever (BU Lock) .............................................................
Close Lever ......................................................................
Dir Lever, Gear (IDL-B) ..................................................
Gear (IDL-C) ...................................................................

4.

TEST MODE ............................................................... 22

5.

ELECTRICAL ADJUSTMENTS

12
12
13
13
14
14
15
16
17
17
18
18
19
19
20
20
21

Deck Section .................................................................... 24

CD Section ...................................................................... 25

6.

DIAGRAMS

6-1. Block Diagram BD/DRIVER Section ......................

TUNER/TAPE DECK Section ..................................
MAIN Section ...........................................................
DISPLAY/POWER SUPPLY Section .......................

28
29
30
31

6-2.
6-3.
6-4.
6-5.
6-6.
6-7.
6-8.
6-9.
6-10.
6-11.
6-12.
6-13.
6-14.
6-15.
6-16.

Printed Wiring Board BD81A Section .....................

Schematic Diagram BD81A Section ........................
Printed Wiring Board TC Section .............................
Schematic Diagram TC Section ...............................
Printed Wiring Board MAIN Section .......................
Schematic Diagram MAIN Section ..........................
Printed Wiring Board PRE AMP Section ..................
Schematic Diagram PRE AMP Section ....................
Printed Wiring Board LCD/DRIVER Section ...........
Schematic Diagram LCD/DRIVER Section .............
Printed Wiring Board PANEL Section .....................
Schematic Diagram PANEL Section ........................
Printed Wiring Board S-MASTER Section ..............
Schematic Diagram S-MASTER Section .................
IC Pin Function Description ............................................

7.

EXPLODED VIEWS

7-1.
7-2.
7-3.
7-4.
7-5.
7-6.

MAIN Section .................................................................

Front Panel Section .........................................................
Lid (TC) Section ..............................................................
Chassis Section ................................................................
S-MASTER AMP Section ...............................................
CD Mechanism Deck Section-1
(CDM80BH-F1BD81) .....................................................
7-7. CD Mechanism Deck Section-2
(CDM80BH-F1BD81) .....................................................
7-8. CD Mechanism Deck Section-3
(CDM80BH-F1BD81) .....................................................
7-9. Base Unit Section (BU-F1BD81A) .................................

8.

32
33
34
35
36
37
38
39
40
41
42
43
44
45
51

57
58
59
60
61
62
63
64
65

ELECTRICAL PARTS LIST .................................. 66

HCD-CPX11
SECTION 1
SERVICING NOTES
SERVICE POSITION OF THE TAPE MECHANISM DECK

tape mechanism deck

SERVICE POSITION OF THE S-MASTER AMP BOARD

Remove the switching regulator, the S-MASTER AMP board block first,
then remove the S-MASTER AMP board from the S-MASTER AMP board block.

S-MASTER AMP board

HCD-CPX11

JUDGING WHETHER THE SWITCHING REGULATOR IS GOOD OR DEFECTIVE

The switching regulator is judged to be good when the terminal voltage at the switching regulator CN4 is 12 V.

switching regulator

CN4

JUDGING WHETHER THE SUB POWER BOARD IS GOOD OR DEFECTIVE

It is judged to be good when the voltage between pin 2 (+4 V) and pin 3 (GND) of the MAIN board CN302 is 4 V.

CN302

MAIN board

SUB POWER board

HCD-CPX11

SERVICE POSITION OF THE CD MECHANISM DECK

Remove the front panel and the circuit boards once in order to remove the CD mechanism deck.
After removing the CDM, reassemble the panel and the circuit boards back to the original state.

CD mechanism deck

Extension cable should be used.

(J-2501-248-A)(1.00mm/27P/300L)

COVER BOARD
This is the board used to blind the slot. Do not remove.

cover board

HCD-CPX11

FIXING THE TC CABLES

To prevent cables from noise, fix the cables with the lead pin so that the cables do not contact with the flexible board.

TC board

lead pin

PREVENTING THE SUB POWER CABLES FROM SAGGING DOWN

Be careful not to contact with the CD mechanism deck.

SUB POWER cable

NG

SUB POWER board

HCD-CPX11

CAUTION SO THAT THE FLEXIBLE BOARD SHOULD NOT CONTACT WITH THE HEAT SINK
When the flexible board is replaced, give the folding at the same position of the new flexible board with that of the old flexible board.

S-MASTER AMP board

HCD-CPX11
SECTION 2
GENERAL

This section is extracted

from instruction manual.

List of button locations and reference pages

How to use this page

Illustration number
r

Use this page to find the location of buttons and other

parts of the system that are mentioned in the text.

DISPLAY wf (13, 20)

R
Name of button/part

R
Reference page

Main unit
BUTTON DESCRIPTIONS

ALPHABETICAL ORDER
AO

PZ

BASS +/ wa (16)
CD SYNCHRO qa (15)
DIRECTION wd (14, 15, 16, 18)
Disc slot ql (8)
DISPLAY wf (13, 20)
Display window 3
DSGX w; (16)
FM MODE qs (12, 25)
FUNCTION 0 (8, 10, 12, 14, 16,
23, 26)

PHONES jack qk
PLAY MODE wd (8, 10, 15, 25,
26)
Remote sensor 2
REPEAT qs (9)
TREBLE +/ ws (16)
TUNER/BAND 9 (11, 12)
TUNING MODE wd (11, 12)
TUNING +/ qd (11, 12)
VOLUME qf (17)

?/1 (power) 1 (7, 12, 17, 18,

26)
TAPE Z (eject) 4 (14)
TAPE nN (play) 5 (14, 15,
16, 18)
TAPE x (stop) 6 (14, 15, 16,
26)
TAPE X (pause) 7 (14, 15, 16)
TAPE z REC (record) 8 (16)
lm/ML (rewind/fast
forward, go back/go forward)
qd (9, 10, 14)
CD NX (play pause) qh (8, 9,
10)
CD x (stop) qj (9, 12, 26)
CD Z (eject) qg (9)

5
6
7
8
9
wf
wd
ws
wa
w;

0
qa
qs
qd
qf
qg

ql
qh
qk

qj

HCD-CPX11

Remote control
BUTTON DESCRIPTIONS

ALPHABETICAL ORDER
AO

PZ

ALBUM +/ qa (9, 10, 15)

CD qh (8, 10)
CLEAR qd (10)
CLOCK/TIMER SELECT 2
(18, 19, 24)
CLOCK/TIMER SET 3 (7, 17,
18)
DISPLAY ql (13, 20)
ENTER 9 (7, 10, 11, 17, 18, 19)
EQ qs (16)
FM MODE 4 (12, 25)
FUNCTION 6 (8, 10, 12, 14, 16,
23, 26)

PLAY MODE qk (8, 10, 15, 25)

REPEAT 4 (9)
SLEEP w; (17)
TAPE qg (14)
TUNER/BAND 5 (11, 12)
TUNER MEMORY qj (11)
TUNING MODE qk (11, 12)
VOLUME +/ 0 (17)

w;

ql
qk
qj
qh
qg
qf

?/1 (power) 1 (7, 12, 17, 18)

x (stop) 8 (9, 14)
X (pause) 8 (9, 14)
N (play) 8 (8, 10, 14, 18)
./> (skip back/skip
forward) qf (7, 9, 10, 16, 17,
18, 19)
m/M (rewind/fast forward)
7 (9, 14)
+/ (tuning) qf (11, 12)

2
3
4
5
6
7
8

qd
qs

*
0

qa

* Button does not function with this model.

Setting the clock

Use buttons on the remote for the operation.

1
2
3
4
5
6

Press ?/1 to turn on the system.

Press CLOCK/TIMER SET.
Press ./> repeatedly to set the
hour.
Press ENTER.
Press ./> repeatedly to set the
minute.
Press ENTER.

The clock starts working.

To adjust the clock

1 Press CLOCK/TIMER SET.

2 Press ./> until CLOCK SET
appears, then press ENTER.

3 Do the same procedures as step 3 to 6

above.
Note

The clock is not displayed in Power Saving Mode.

10

HCD-CPX11
SECTION 3
DISASSEMBLY
This set can be disassembled in the order shown below.

SET

3-1.COVER
(Page 12)

3-2.FRONT PANEL SECTION

(Page 12)

3-3.TC BOARD,
MECHANICAL DECK
(Page 13)

3-5.MAIN BOARD,
PRE AMP BOARD
(Page 14)

3-4.PANEL BOARD
(Page 13)

3-6.CD MECHANISM DECK

(CDM80BH-F1BD81)
(Page 14)

3-7.CHASSIS (TOP)
(Page 15)

3-10.DRIVER BOARD
(Page 17)

3-12.BU SECTION
(Page 18)

3-13.OPTICAL PICK-UP
(KSM-215DCP)
(Page 19)

3-11.BD81A BOARD
(Page 18)

3-8.LEVER (LOADING R/L)

(Page 16)

3-9.DISC STOP LEVER,

DISC SENSOR LEVER
(Page 17)

3-14.LEVER (BU LOCK)

(Page 19)

3-15.CLOSE LEVER
(Page 20)

3-16.DIR LEVER,
GEAR (IDL-B)
(Page 20)

3-17.GEAR (IDL-C)
(Page 21)

11

HCD-CPX11

Note: Follow the disassembly procedure in the numerical order given.

3-1. COVER
3 three screws
(+BVTP 3 6)

5 cover

2 two case screws

1 two case screws

3-2. FRONT PANEL SECTION

1 screw (+BVTP 3 6)

2 wire (flat type) 19 core (CN603)

4 wire (flat type) 19 core (CN303)

8 front panel section

3 connector 4p (CN102)
5 wire (flat type) 9 core (CN304)
6 screw (+BVTP 3 6)
7 three screws (+BVTP 3 6)

12

HCD-CPX11

3-3. TC BOARD, MECHANICAL DECK

2 wire (flat type) 8 core

1 four screws (+BVTP 3 8)

5 TC board

6 mechanical deck
4 connector (6p)

3 three screws
(PTPWH2)

3-4. PANEL BOARD

5 lid (TC) section

4 two dowels
9 cover (eject)
8 two screws (+BVTP 2.6 10)
2 two buss knobs
3 spring (LID TC)
tortion

qa PANEL board

7 holder

spring (LID TC)

torsion
1 volume knob
q; two screws (+BVTP 2.6 8)

6 five screws
(+BVTP 2.6 8)

13

HCD-CPX11

3-5. MAIN BOARD, PRE AMP BOARD

3 back panel
6 connector 2p (CN301)
7 wire (flat type) 15 core (CN307)

2 two screws (+BVTP 3 6)

8 wire (flat type) 22 core (CN309)

1 five screws (+BVTP 3 6)

5 wire (flat type) 19 core
qd two screws (+BVTP 3 6)

q; wire (flat type) 27 core (CN201)

qa connector 3p (CN302)
qf PRE AMP board
9 connector 7p (CN202)
qs MAIN board
4 two screws (+BVTP 3 6)

3-6. CD MECHANISM DECK (CDM80BH-F1BD81)

7 CD mechanism deck

5 S-MASTER AMP section

2 two screws
(+BVTP 3 6)

SUB POWER board

1 connector 2p (CN990)

4 screw
(+BVTP 3 6)
6 four screws (+BVTP 3 10)

14

3 screw (+BVTP 3 6)

HCD-CPX11

3-7. CHASSIS (TOP)

3 three screws
(+BVTP 2.6 8)

1 screw
(+BVTP 2.6 8)
2 lever (CL UP2)

4 two screws
(+P 2 10)

5 chassis (top)

15

HCD-CPX11

3-8. LEVER (LOADING R/L)

spr-T (loading L)

spr-T (loading R)

6 lever (loading R)
3 two hooks
5 two hooks
4 lever (loading L)

PRECAUTION DURING LEVER (LOADING R / L) INSTALLATION

Align the horizontal position.

lever (loading L)

lever (loading R)

Install the both levers so that they move symmetrically.

16

HCD-CPX11

3-9. DISC STOP LEVER, DISC SENSOR LEVER

1 gear (cap)
2 gear (IDL L)

PRECAUTION DURING DISC STOP LEVER INSTALLATION

hole

chassis (top)

5 two hooks
3 two claws

disc stop lever

6 disc stop lever

hole

4 disc sensor lever

Install the disc stop lever so that the both holes

are aligned.

3-10. DRIVER BOARD

2 three screws
(+BVTP 2.6 8)
3 Remove soldering
from the two points.

5 DRIVER board

4 motor (pully) assy

1 belt (MOT)

17

HCD-CPX11

3-11. BD81A BOARD

1 screw
(+BVTP 2.6 8)

6 BD81A board

2 Remove soldering
from the four points.

4 sheet

5 wire (flat type)

(16 core)
3 wire (flat type)
(16 core) (CN102)

3-12. BU SECTION
6 BU section

4 floating screw
(+PTPWHM 2.6)

3 213 holder down spring

5 floating screw
(+PTPWHM 2.6)

2 lever (CL UP2)

1 screw
(+BVTP 2.6 8)

18

HCD-CPX11

3-13. OPTICAL PICK-UP (KSM-215DCP)

6 two insulators

1 two screws
(+BVTP 2.6 8)
2 two stoppers (BU)

4 two floating screws

(+PTPWHM 2.6)
8 optical pick-up

3 two coil springs (insulator)

5 two coil springs (insulator)

7 two insulators

3-14. LEVER (BU LOCK)

4 lever (BU lock)

3 three hooks

1 gear (cap)
2 gear (BU lock)

19

HCD-CPX11

3-15. CLOSE LEVER

1 washer (3-1-0.4)

5 close lever

3 claw
2 close lever spring

4 shaft disc stop

3-16. DIR LEVER, GEAR (IDL-B)

2 claw

3 gear puley
4 gear (cap)
5 gear (IDL-A)
8 stopper

9 DIR lever

q; gear (IDL-B)
1 DIR spring

6 Loosen the screw.

7 Hold the Release lever

and change the direction.

20

HCD-CPX11

3-17. GEAR (IDL-C)

3 gear (IDL-D)

2 two claws

4 three hooks

1 gear (IDL-F)
5 gear loading lever
7 gear (IDL-C)

6 claw

21

HCD-CPX11
Ver 1.1

SECTION 4
TEST MODE

[CMN (MC) TEST MODE]

This mode is used to check operations of Amplifier.
Procedure:
1. Press the ?/1 key to turn the power ON.
2. Press three keys of [DSGX], [FUNCTION] and [TUNER/BAND]
simultaneously.
3. When the CMN (MC) test mode is activated, s blinks
on the liquid crystal display.
4. Turn the [BASS] knob counterclockwise, TONE MIN is
displayed on the liquid crystal display. Turn the [BASS] knob
clockwise, TONE MAX is displayed on the liquid crystal
display.
Turn the [TREBLE] knob clockwise or counterclockwise,
TONEFLAT is displayed on the liquid crystal display.
Turn the [VOLUME] knob counterclockwise, VOL MIN is
displayed on the liquid crystal display. Turn the [VOLUME]
knob clockwise, VOL MAX is displayed on the liquid crystal
display.
5. To release this mode, press the ?/1 key.
[PANEL (GC) TEST MODE]
This mode is used to check the liquid crystal display, LED,
model, destination, software version and key.
Procedure:
1. Press the ?/1 key to turn the power ON.
2. Press three keys of [DSGX], [DISPLAY] and [FUNCTION]
simultaneously.
3. Liquid crystal display and LEDs are all turned on.
4. When you want to enter the model, destination and version
display mode, press the [REPEAT] key. The model and
destination are displayed alternately on the liquid crystal
display.
5. Each time [REPEAT] key is pressed, the display changes
starting from MD version, MC version, GC version, CD
version, CDD version, CDMA version, CDMB version, BDA
version, BDB version, ST version, TA version, TM version,
and TC version this order, and returns to the MD version
display on the liquid crystal display.
6. When [FUNCTION] key is pressed while the version numbers
are being displayed except model and destination, year, month
and day of the software creation display. When [FUNCTION]
key is pressed again, the display returns to the software version
display. When [REPEAT] key is pressed while year, month
and day of the software creation are being displayed, the year,
month and day of creation of the software versions are
displayed on the liquid crystal display in the same order of
version display.
7. Press the [PLAY MODE/DIRECTION] key, the key check mode
is activated.
8. In the key check mode, the liquid crystal display displays K0.
Each time a key is pressed, K value increases. However,
once a key is pressed, it is no longer taken into account.
9. To release this mode, press three keys in the same manner as
step 2, or disconnect the power cord.
[COLD RESET]
The cold reset clears all data including preset data stored in
the RAM to initial conditions. Execute this mode when
returning the set to the customer.
Procedure:
1. Press the ?/1 key to turn the power ON.
2. Press three keys of ?/1 , x (CD) and x (TAPE) simultaneously.
3. The liquid crystal display becomes blank instantaneously, and
the set is reset.

22

[SHIP MODE (NO MEMORY CLEAR) ]

This mode moves the optical pick-up to the position durable
to vibration. Use this mode when returning the set to the
customer after repair.
Procedure:
1. Press the ?/1 key to turn the power ON.
2. Press the [FUNCTION] key to select CD.
3. Press three keys of [DSGX], CD NX and [DISPLAY]
simultaneously.
4. After the STANDBY display blinks, LOCK is displayed
on the liquid crystal display, and the ship mode is set.
[SHIP MODE (MEMORY CLEAR) ]
This mode moves the optical pick-up to the position durable
to vibration. Use this mode when returning the set to the
customer after repair.
Procedure:
1. Press the ?/1 key to turn the power ON.
2. Press the [FUNCTION] key to select CD.
3. Press three keys of [DSGX], x (CD) and [DISPLAY] simultaneously.
4. After the STANDBY display blinks, LOCK is displayed
on the liquid crystal display, and the ship mode is set.
[CD TRAY LOCK MODE]
This mode is used to unable to take sample disc out of tray in
the shop.
Procedure:
1. Press the ?/1 key to turn the power ON.
2. Press the [FUNCTION] key to select CD.
3. While pressing the Z (CD) key, press the x (CD) key for
5 seconds.
4. The message LOCKED is displayed on the liquid crystal
display and the tray is locked. (Even if pressing the Z (CD)
key, the message LOCKED is displayed on the liquid crystal
display and the tray is locked)
5. To release from this mode, pressing the Z (CD) key, press
the x (CD) key for 5 seconds.
6. The message UNLOCKED is displayed on the liquid crystal
display and the tray is unlocked.
[TUNER STEP CHANGE MODE]
(Singapore, Korean and Australian models)
A step of AM channels can be changed over between 9 kHz
and 10 kHz.
Procedure:
1. Press the ?/1 key to turn the power ON.
2. Press the [FUNCTION] key to select TUNER, and press the
[TUNER/BAND] key to select AM.
3. Press the ?/1 key to turn the power OFF.
4. Press two keys of ?/1 and M L simultaneously.
5. The message AM 9K STEP or AM 10K STEP is displayed
on the liquid crystal display, and thus the channel step is
changed over.
[CD SERVICE MODE]
This mode can run the CD sled motor freely. Use this mode,
for instance, when cleaning the optical pick-up.
Procedure:
1. Press the ?/1 key to turn the power ON.
2. Press the [FUNCTION] key to select CD.
3. Press three keys of [PLAY MODE] , [FUNCTION] and
x (TAPE) simultaneously.
4. Press the M L key to move the optical pick-up to outside
track, or press the l m key to inside track.
5. To release this mode, press the ?/1 key.

HCD-CPX11
Ver 1.1

[CD ERROR CODE MODE]

This mode can be used for error display of CD section.
Procedure:
1. Press the ?/1 key to turn the power ON.
2. Press the [FUNCTION] key to select CD.
3. Press three keys of [REPEAT], [FUNCTION] and x (TAPE)
simultaneously.
Note: Error code is not displayed on the liquid crystal display.

[CD SERVO TEST MODE]

This mode used to ckeck operation of optical pick-up.
Procedure:
1. Press the ?/1 key to turn the power ON.
2. Press the [FUNCTION] key to select CD.
3. Press three keys of [DSGX] , [FUNCTION] and x (TAPE)
simultaneously.
4. When the CD servo test mode is activated, optical pick-up
moves.
[5 REPEAT OFF MODE]
Number of repeat for CD playback is 5 times when the repeat
mode is REPEAT. This mode is used to enables CD to repeat
playback for limitless times.
Procedure:
1. Press the ?/1 key to turn the power on.
2. Press the [FUNCTION] key to select CD.
3. Press three keys of [DSGX] , [FUNCTION] and Z (CD)
simultaneously.
4. When the 5 repeat off mode is activated, LIMIT OF is
displayed on the liquid crystal display.
[CHANGE-OVER FUNCTION OF EXTERNAL INPUT]
This mode is used to enable function of external input to change
over between MD and VIDEO.
Procedure:
1. Set to standby state.
2. Press two keys of ?/1 and [FUNCTION] simultaneously.
3. The function of external input changes over to MD or VIDEO.

23

HCD-CPX11
SECTION 5
ELECTRICAL ADJUSTMENTS
DECK SECTION

TC BOARD (Component Side)

0 dB = 0.775 V

Note:

Confirm each contents of this section first of all. If the results are
not satisfied, do the adjustment.
1. The adjustments should be performed with the rated power
supply voltage unless otherwise noted.
2. The adjustments should be performed in the order given in
this service manual.
3. The adjustments should be performed for both L-CH and RCH.

AF OSC

MAIN board
MD (VIDEO) IN jack (J101)
L-CH, R-CH
1) 315 Hz
34.6 mV ( 27 dB)
2) 10 kHz
attenuator

600

blank tape
CN-123

set

5. Mode: Playback
recorded
portion

level meter
set

SP board
SPEAKER terminals (J860)
L-CH, R-CH

6. Confirm the playback signal recorded in step 3 becomes

adjustable level as follows.
If these levels are out of specified values, adjust the RV653
(L-CH) and RV603 (R-CH) on the TC board to repeat steps 4
and 5.
Specified values: Playback output of 315 Hz to playback
output of 10 kHz: 2.0 dB
Adjustment Location: TC board

24

REC Bias
Adjustment

REC BIAS ADJUSTMENT

Procedure:
1. Press the [FUNCTION] key to select MD or VIDEO.
2. Set the tape into the deck.
3. After pressing z REC key, press X (TAPE) key to start
recording.
4. Mode: Record

(R-CH)

(L-CH)

RV603

RV653

HCD-CPX11

Checking Location:
BD81A BOARD (Side B)

CD SECTION
Note:

1. CD Block is basically constructed to operate without

adjustment.
2. Use YEDS-18 disc (3-702-101-01) unless otherwise indicated.
3. Use an oscilloscope with more than 10 M impedance.
4. Clean the object lens by an applicator with neutral detergent
when the signal level is low than specified value with the
following checks.
5. Check the focus bias check when optical pick -up block is
replaced.

IC251

FOCUS BIAS CHECK

IC301

oscilloscope
(DC range)
BD81A board
TP (RFAC)
TP (VC)

TP
(VC)

IC101

Procedure :
1. Connect oscilloscope to TP (RFAC) and TP (VC) on the
BD81A board.
2. Press the ?/1 button to turn the power ON, and press the Z
(CD) button to open the CD disc tray.
3. Set disc (YEDS-18) on the tray and press the CD NX button
to playback.
4. Confirm that oscilloscope waveform is as shown in the figure
below. (eye pattern)
A good eye pattern means that the diamond shape () in the
center of the waveform can be clearly distinguished.

TP
(RFAC)

VOLT/DIV: 200 mV
TIME/DIV: 500 ns

level:
0.9 0.4 Vp-p

25

HCD-CPX11

MEMO

26

HCD-CPX11
SECTION 6
DIAGRAMS
Circuit Boards Location

THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is printed in each block.)
For Schematic Diagrams.
Note:
All capacitors are in F unless otherwise noted. (p: pF)
50 WV or less are not indicated except for electrolytics and
tantalums.
All resistors are in and 1/4 W or less unless otherwise
specified.

f : internal component.
5 : fusible resistor.
C : panel designation.
Note: The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part number specified.
A : B+ Line.
H : adjustment for repair.
Voltages and waveforms are dc with respect to ground under no-signal (detuned) conditions.
no mark: TUNER (FM)
(
): CD PLAY
[
] : TAPE PLAY

: REC
Voltages are taken with a VOM (Input impedance 10 M).
Voltage variations may be noted due to normal production
tolerances.
Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production
tolerances.
Circled numbers refer to waveforms.
Signal path.
F
: TUNER (FM/AM)
J
: CD PLAY (ANALOG)
c
: CD PLAY (DIGITAL)
E
: TAPE PLAY
a
: REC
j
: MD (VIDEO) IN
Abbreviation
AUS
: Australian model.
KR
: Korean model.

For Printed Wiring Boards.

Note:
X : parts extracted from the component side.
Y : parts extracted from the conductor side.

W : indicates side identified with part number.

f
: internal component.

: Pattern from the side which enables seeing.

(The other layers' patterns are not indicated.)

S-MASTER AMP board

TC board

Caution:
Pattern face side: Parts on the pattern face side seen from
(Side B)
the pattern face are indicated.
Parts face side: Parts on the parts face side seen from
(Side A)
the parts face are indicated.

SP board

Indication of transistor.

PANEL board

C
Q

These are omitted.

SUB POWER board

B E

HP board
Q
B C

E
These are omitted.

SUB PANEL board

Q
B

E
These are omitted.

SWITCHING REGULATOR
MAIN board
LCD board

BACK LIGHT board

PRE AMP board

DRIVER board

BD81A board

27

27

HCD-CPX11
6-1. BLOCK DIAGRAM BD/DRIVER SECTION

OPTICAL PICK-UP
BLOCK
DETECTOR
VCC
VC

IC301
DIGITAL SIGNAL
PROCESSOR

IC101
RF AMP

+1.7V
+3.3V

IC303
A

26 A

PCMD1 61

11 SDO0

VDD 55

27 B

LRCK1 62

16 LRCKIA

VDD 21

28 C

LRCK 63

19 SFSY/LRCK1B

29 D

PCMD 65

14 SDIO

19 E

BCK 66

20 F

BCK1 60

REG

3.3V

VDDM 40

IC300(1/4)
SYSTEM CONTROLLER

15 BCKIA
18 SBSY/BCK1B

IC701
(LC)MOTOR DRIVER

Q10
LD

LD
DRIVER

GND

37 PD
+3.3V

VR
IC251
SL/SP MOTOR
DRIVER
FOCUS
COIL

F
T+

TRACKING
COIL

MIACK 8
MICK 7

3
7

MIDIO 6

MP3 DATA OUT

MILP 5

MILP

XTACN

MICS 4

22 MICS

XRST

RESET 2

78 XTAI
XTACN 95

PD

XRST 100
DATA 102

7 SSTP
SW101

XLAT 104
CLOCK 105
SENS 107

16 CH2OUT-F
CH1FIN 5

11 TFDR

15 CH2OUT-R
CH1RIN 6

12 TRDR

17 CH1OUT-R

SCOR 115

CDM-LOAD-OUT 25

MP3REQ
MIACK

9 RIN
7 FIN

CDM-LOAD-IN 24

23 MP3STB

PO11/BUCK/AD1 36

77 XTAO
X171
16.9MHz

F+

STANBY 3

36 LD

MP3CLK

21 MP3RST

DATA
XLAT

SCOR

CLOCK

SENS

SENS

CLOCK

SCOR

XLT
DATA
XRST

GFS 113

XTACN

19 CD SCOR
32 CD SENS
37 CD CLK
36 CD XLT
35 CD DATA

CDM SW2 28
CDM SW1 27

33 CD XRST

CDM SW3 26

34 CD XTCN

CD MUTE 60

S702
S701
S703

C2PO 114

CH2FIN 7

13 FFDR

18 CH1OUT-F

CH2RIN 8

14 FRDR

FOK

2
3

M101
(SPINDLE)

19 CH4OUT-F

SFDR 9

30 CH3FIN

SRDR 10

29 CH3RIN

OPIN+ 3

6 MPD

20 CH4OUT-R

M102
(SLED)

CD L-CH

AOUT1 81

MAIN
Section

21 CH3OUT-R

AOUT2 86

R-ch is omitted due to same as L-ch.

R-CH

Signal Path

22 CH3OUT-F
MUTE 24

OPTICAL
TRANSEIVER
IC450

DOUT 71

CD DIGITAL OUT
OPTICAL

: CD PLAY(ANALOG)
: CD PLAY(DIGITAL)

MUTING
Q342
R-CH
MUTING CONTROL
SWITCH
Q340,341

28

28

OUT1 4
OUT2 2

M701(LOADING)

HCD-CPX11
TUNER/TAPE DECK SECTION

ANTENNA

TUNER UNIT

FM 75
COAXIAL

FM ANT

L-CH

ANT GND

R-CH

TUNER
L-CH

DO
CLK
CE
MUTING
TUNED
STEREO
RAS DATA
RDS INT

37
39

R-CH

MAIN
Section

MAIN
Section

REC/PB EQ AMP, ALC

IC601

L-CH

R-CH

DI

ST DOUT
ST DIN
ST CLK
ST CE
ST MUTE
TUNED
STEREO
RAS DATA
RDS INT

ANT GND

MAIN
Section

R-CH

AM ANT
AM

BIN (R)

EQOUT (R)

AIN (R)

TAI (R) MUTE

PB OUT (R)

PB
L-CH

9
R-CH

4
REC/PB SWITCHING
IC602
8

HRPE901
(REC/PB/ERASE)

SWITCHING
Q680, 681

BIAS
TRAP

REC BIAS
(R)

REC BIAS
(L)
BIAS OSC
T601

R-CH

REC BIAS
SWITCH
Q639 641

ERASE

A+9V

REC-IN (R)

EQ

REC MUTE ON/OFF

RV653

RECOUT (R)

ALC ON/OFF

RV603

10

MUTE ON/OFF

R-CH

11

14

15

ALC

ALC (R)

REC
L-CH

R-CH

(TAPE DECK BLOCK)

TC CAPM-CONT 70

67

48 49 47 50 53 51 52 54 18

61

66

65

ST DATA IN
ST DATA OUT
ST CLK
ST CE
ST MUTE
ST TUNED
ST STEREO
RDS DATA
RDS CLK

TC ALC

TC LINE MUTE

TC REC/MUTE

: TUNER (FM/AM)

TC TRG 71

TC PB/REC

R-ch is omitted due to same as L-ch.

Signal Path

DI
DO
CLK
CE
MUTING
TUNED
STEREO
RDS DATA
RDS CLK

BIAS OSC
Q642, 643

68 TC BIAS-ON

TC END SW 90
TC PLAY SW 69
SYSTEM CONTROLLER
IC300 (2/4)

: TAPE PLAY
: REC

29

29

TC HALF/REC/SW 91

CAPSTAN/REEL
MOTOR DRIVE
Q692, 694
TRIGGER
PLUNGER DRIVE
Q691, 693

M
(CAPSTAN/REEL)

HCD-CPX11
MAIN SECTION

HEADPHONE AMP
IC102
6
5

TUNER +9V,
TC A+9V

RIPPLE FILTER
Q180, 181

30

DOUT 12
BCK 11
LRCK 10

1 LIN

2 RIN

MUTING
Q151
INPUT SELECT SWITCH,
ELECTRICAL VOLUME,
TONE CONTROL
IC101

R-CH

MUTING
CONTROL SWITCH
Q121, 122

DIGITAL AUDIO
SIGNAL PROCESSOR
IC600
18 DATA
17 BCK
16 LRCK

15

21 11 12 13

15 14

POWER AMP
IC650
OUTL1 2
OUTL2 4
OUTR1 41
OUTR2 39

6 INA
16 INB

OUTA 9
OUTB 19

R-CH
R-CH
DIAGA
DIAGB

EQ DATA

R-CH

A/D CONVERTER
IC603

ENA
ENB

TONE
CONTROL

CPU
INTERFACE

L
R

VOLUME
CONTROL

LCH
OUT

R-CH

J101

MD (VIDEO)
IN

LCH
IN

VBBB

TUNER
L-CH

LCH
INPUT SELO
10
SELECT
SWITCH

XFSOIN

CD LCH
11
TC LCH
12
TUNER LCH
13
MD LCH
14

INIT
NSPMUTE

PB
L-CH

SCDT
SCSHIFT
SCLATCH

TUNER/TAPE DECK
Section

MUTING
CONTROL SWITCH
Q184, 185

XFSIIN

CD
L-CH

SCKI

TUNER/TAPE DECK
Section

R-CH

PDWN

HEADPHONE
MUTING
Q183

REC
L-CH

EQ CE

MAIN
Section

EQ CLK

TUNER/TAPE DECK
Section

J801
PHONES

R-CH

36

11

7 17

8 18

PD
+3.3v
CLOCK
BUFFER
IC604

PROTECT
DETECT
Q691, 692

R-CH
R
R-CH

PROTECT
SWITCH
Q696

A+28v

R-CH

CLOCK
BUFFER
IC610

X602
49.152MHz

X601
12.288MHz

SYSTEM CONTROLLER
IC300(3/4)

: REC
: MD (VIDEO) IN

30

30

42 43 44

46 45

41

40

58

100

ENA

DIAG

HP MUTE

HP DET

59

INIT
NSP MUTE

57

SC DT
SC SHIFT
SC LATCH

: TAPE PLAY

55

LINE MUTE

: CD PLAY

75

EQ CE

: TUNER (FM/AM)

EQ CLK

Signal Path

EQ DATA

R-ch is omitted due to same as L-ch.

J860
SPEAKER
IMPEDANCE
USE 4

HCD-CPX11
DISPLAY/POWER SUPPLY SECTION

64-61

SEG1 SEG36

LIQUID CRYSTAL
DISPLAY
LCD800

Vcc 63

DATA
SCL
CE
MODE
INH

COM1 COM4

1-36

LIQUID CRYSTAL
DISPLAY DRIVER
IC801

58
57
56
59
60

REMOTE CONTROL
RECEIVER
IC802

LED STANDBY 81

LED DRIVE
Q813

D813
(STANDBY)

LED DSG 82

LED DRIVE
Q812

DSGX

LED CD 89

LED DRIVE
Q870

CDNX

LED TUNER 80

LED DRIVE
Q816

TUNER/BAND

LED TC 79

LED DRIVE
Q818

TAPEnN

LCD
+3.3V
75
76
77
73
72

LCD DATA/EQ DATA

LCD SCL
LCD CE
LCD MODE
LCD INH

D870

T991
SUB POWER
TRANSFORMER

KEY1 KEY3
95
,

RESET 12

94
D374, 375

D304

SWITCH
Q331, 332

+1.8V

83 TRE A
84 TRE B

A+3.3V,
D+3.3V

85 BASS A
86 BASS B

D301
D302

+1.8V
REGULATOR
IC618

D202

CD ON
SWITCH
Q201,202

D203

CD BD-PWR 38

D201

SYSTEM CONTROLLER
IC300 (4/4)
D806,807
(LCD BACK LIGHT)

RECT
D992 995

D303

-COM+3.3V
PD+3.3V

+12V

RDS+3.3V

+4V
REGULATOR
IC203

A+5V,
D+5V

+5V
REGULATOR
IC204

SWITCH
Q333, 334
D205

LCD ON/LED BL 78
D+6.2V

XCIN

13

15

11

10

X401
16MHz

M+7V

+7V
REGULATOR
IC202

TUNER +9V,
TC A+9V

+9V
REGULATOR
IC201

A+28V
POWER ON/OFF
RELAY DRIVE
Q991

PWR RELAY 39

XCOUT

BASS

ROTARY
ENCODER
RV805

+4V
REGULATOR
IC991

EVER
+3.3V

87 VOL A
88 VOL B

XIN

TREBLE

ROTARY
ENCODER
RV804

D401

RESET
IC401

LCD+3.3V

XOUT

ROTARY
ENCODER
RV803

RESET
SWITCH
Q401

AC CUT 20
74 KEY WAKE UP

VOLUME

D816

D818
4 SIRCS IN/WAKE

97
,
S801 817

D812

POWER ON/OFF
RELAY DRIVE
Q990

SWITCHING
REGULATOR
RY991

RY990

AC IN

X402
32.768kHz

31

31

HCD-CPX11
6-2. PRINTED WIRING BOARD BD81A SECTION

See page 27 for Circuit Boards Location.

:Uses unleaded solder.

SPINDLE
MOTOR

IC303

(LIMIT)

36

28

27

19

IC301 1

16

64

17
1

10

SLED
MOTOR

18

IC251
32
33

49
48

TP
(VC)

D
IC101

12

12

12

MAIN
BOARD
CN201
(Page 36)

12
E

TP
(RFAC)

OPTICAL
PICK-UP
BLOCK
(KSM215DCP)

32

32

Semiconductor
Location
Ref. No.
IC101
IC251
IC301
IC303

Location
D-7
C-6
C-7
B-7

Q10

E-4

HCD-CPX11
Refer to page 51 for IC PIN FUNCTION DESCRIPTION.

6-3. SCHEMATIC DIAGRAM BD81A SECTION

C11
10
6.3
B

C15
0.1
F

C10
10
6.3
B

CN101
16P

R307 10k

C309
0.1 F

TP122

TP123

C122
0.1
B

B
C123 0.1

R121 15k

C131 100p CH

R131 1M

C124
330p CH
TP124 RFACO

TP15 PD
TP16 F+
TP17 F-

TP104
PCMD
TP105
BCK

R354 100
R401 100
R301 100k

TP301

R306 0

C318
0.01
B

R111 1k C111 0.0033

R112 15k

C161
0.1 F

JPO102

R305
100k

C316
0.0022 B

R113 1k

C162 0.1

C320
0

R313 C315
220 0.1 B
C313 0.1

R171
470

C172 27p CH

TEI

C115 0.1

TP428
FRDR

IC101
CXD3059AR

TP429
FFDR
TP430
TRDR

X171 16.9MHz

R182
100
C186 470p

CH

C183 22 6.3V

TP432
MDP

C184 22 6.3V

C182 0.1

TP167
LOCK

TP178
FOK
TP166
DFCT
TP165
MIRR

C305
220
4V

C210
0.1 B

TP186
MVDD

TP160
WDCK
TP162
COUT

R251 R252
22k
10k
S101
SW

JPO004
MDP

C251
0.0068
B

C259
0.1
F

C258
0.1

TP426
SW-

C196 0.1

R163
100

R165
0

C163
0.1

R191 0

TP145
WFCK
TP144
XUGF
TP147
XPCK
TP153
GFS
TP146
C2PO

TP148
SBSO
TP149 EXCK

TP142

TP425
SW+

C194
0.1
F

CN201
27P

TP431
TFDR

CH

R181
C181
100
0.1 F

TP433
MP3VDD

C116
100
10V

C195 0.1

C185 470p

TP177
VC

R173 0

C312
0.1 F

R114 15k
C114 470p

C171
C174
0.1 F 22p CH

C314 47 4V

JPO103

C112 470p
C113 0.0033

FEI

R161 100

C317
0.01 B

R172
1M

TP422
MP3GND

R353 100
R402 100

C303
0.1
F

C18 0.001

TP103
LRCK

R352 100

C302
0.1
F

TP14 C
TP102

TP19 F-

R403 100

FB301
BLM21B272S

TP13 B

R11
0

JPO10
APC

TP18 T-

R419 100

IC303
BH15FB1WG

TP12 A

Q10
2SB1690K

R404 100

C310
0.1 F

C311
0.1 F

TP11 D

TP424
IOP2

R10
3.3

TP427
PCMDI

R405 100

IC301
TC94A34FG-002

TP10 E

R13
1

C306
0.1 F

R302
10k

R303 100k

TP423
IOP1

C16
1
F

C17
220
4V

TP121
RFDCO

R351 100

R12
100k

R132
10k

R141 4.7k

TP303

C308
47
4V

R133
180k

C143
0.1 F

TP302

R142
1k

R203
0

C141
0.1 B

R151 0

R143
3.3k

C133 0.01

C151
100
10V

C125
0.1 F

TP125 RFACI

TP304

C132
0.47 B

C134
0.1 F

C142
0.0015 B

C307
0.1 F

R253
10k

R162
47k

TP187
MGND

TP407

MICS

TP408

MP3RST

(Page 37)

TP416 SENS
TP415 CLK
TP414 XLT
TP413 DATA
TP412 XRST
TP419 XTCN
TP434 AVDD

C203
100
10V

TP420
AGND

R205 0
TP417 SCOR

MAIN
BOARD
CN201

C201
100
10V

R411 100
C252
0.1 F

R410 100

M102

R408 100
R407 100
R406 100
R412 100
C260
220 10V

C213 22p CH
C211 220p

CH

TP410 ROUT

TP411 LOUT

TP409

DOUT
R204
0

M101

TP421
DGND

R409 100

C212 22p CH

TP250
SP-

MILP

TP252 SL+

MIDIO

TP406

TP251 SP+

MICK

TP405

C257
0.1 F

TP404

IC251
BA5947FM
(HSOP28)

TP436
AVDD

R201 0

MIACK

TP253 SL-

MP3STB

TP402 MP3REQ
TP403

C209
0.01 B

TP401

TP435 DVDD

33

33

C255
0.1 F

HCD-CPX11
6-4. PRINTED WIRING BOARD TC SECTION

See page 27 for Circuit Boards Location.

:Uses unleaded solder.

Semiconductor
Location
TAPE
MECHANISM
DECK

MAIN
BOARD
CN306

E
E

(Page 36)

21

20

30

11

31

10

E
40

IC601
E

IC602

HRPE901
(REC/PB/ERASE)

F
1
2

L-CH

3
4

R-CH

5
6

HEAD RELAY
BOARD

34

34

ERASE

Ref. No.

Location

D681

B-3

IC601
IC602

D-4
E-4

Q639
Q640
Q641
Q642
Q643
Q680
Q681
Q691
Q692
Q693
Q694

C-2
C-3
C-3
E-2
D-2
D-3
D-3
B-3
B-3
B-2
B-3

HCD-CPX11
6-5. SCHEMATIC DIAGRAM TC SECTION

CN602
8P

IC602
BA3126N

R694
22k
R693
47k
R688
4.7k

R680
4.7k

Q681
DTA124ESA

Q680
DTC114ESA-TP

JW630
0

R689
4.7k

C601
47
16V

R687
47k

Q693
2SB1116

R682
2.2k

R683 680

R611
22k

C681 0.0047

R608
10k

R684 3.3k

C608
2.2
50V

Q694
2SB1068

R695
10k

D681 1SS355TE

C605
10
50V
C606
1
50V

R609
2.2k

R686 3.3k

R603
3.3k

R601
4.7k

C604
0.1
C602
0.01

C607
470p

R604
10k

R685 3.3k

R602
4.7k

R681
2.2k

R690
4.7k

C635
1 50V

C630
100
16V

R631
22k
R630
1M

IC601
HA12237F

CN603
19P

R691
10k
R692
4.7k

Q692
DTC114EKA

Q691
DTC114EKA

C632
10 50V

C663
390p
C611 120p
C613
390p

L601

C614 0.01
R607 10k

JR602 0
L651
RV603 RV653
220k
220k

R657 10k
C660
330p

C664 0.01

R606
2.2k

R605
47k

R656
2.2k

R655
47k

C633
10
50V

R635
100

Q643
2SC2001
T601

Q641
2SD1387-34-TP

R642
2.2k

R641
6.8k

C639
10
50V

C654
0.1

R651
4.7k

C655
10
50V

R653
3.3k

C646 0.018

C642
0.01

C652
0.01
R645 18k

R644
5.6
1/4W

R646 18k

R643
5.6
1/4W

C645 0.0068

C641
2.2
50V

C662
27p

C643 0.015

Q642
2SC2001

C612
27p

R652
4.7k

R654
10k

C656
1
50V

C657
470p

Q639
2SA1175
L640
JW

C640
47
16V

R647
22k
R648
2.2k

R640
10k
C647
10
50V

Q640
DTC114ESA-TP

R632 1k
R633 10k

C651
47
16V

R660 8.2k

C661
120p

C644 0.0068

NO601
8P

C634
10
50V

R610 8.2k
C610
330p

L641
JW

35

35

C658
2.2
50V

R659
2.2k

R658 R661
10k 22k

(Page 37)

HCD-CPX11
6-6. PRINTED WIRING BOARD MAIN SECTION

See page 27 for Circuit Boards Location.

:Uses unleaded solder.

6
B

7
TC
BOARD
CN603

(Page 34)

10

11

SUB POWER
BOARD
NO992

Semiconductor
Location

(Page 44)

IC202

IC203

IC201

AUS,KR

AEP,UK

KR,AUS

IC300

AEP,UK

IC204
3

1
E

AEP,UK

SWITCHING
REGULATOR

(Page 44)

D
IC401

PRE AMP
BOARD
CN101

DRIVER
BOARD
CN701

IC201
IC202
IC203
IC204
IC300
IC401
IC450

B-9
B-7
B-8
B-9
C-4
D-3
I-10

Q201
Q202
Q331
Q332
Q333
Q334
Q340
Q341
Q342
Q343
Q401

F-8
F-7
F-3
F-3
E-2
E-2
E-8
E-9
F-9
F-9
D-3

(Page 38)
E

(Page 40)

F
E

LCD
BOARD
CN805

Location
D-6
D-7
D-7
D-7
C-7
D-5
D-5
D-5
D-5
C-9
C-9
B-9
B-4
B-4
D-4
E-4
D-3
D-3
F-9
F-9

KR,AUS

Ref. No.
D201
D202
D203
D204
D205
D301
D302
D303
D304
D350
D351
D352
D374
D375
D401
D402
D403
D404
D442
D443

27

26

(Page 40)

G
PANEL
BOARD
CN801

(Page 42)

(CHASSIS)

BD81A
BOARD
CN201

(Page 32)

S-MASTER AMP
BOARD
CN601

(Page 44)

H
KR,AUS
TUNER
UNIT

AEP,UK

IC450
1

CD DIGITAL OUT
(OPTICAL)

(CHASSIS)

36

36

HCD-CPX11
6-7. SCHEMATIC DIAGRAM MAIN SECTION

Refer to page 54 for IC PIN FUNCTION DESCRIPTION.

C332
10
50V

Q333
DTA123YKA

D374
1SS355
Q334
DTC114EKA
R379 100

R380 100

R376 100

R377 100

R375 100

R378 100

R474 1M
R372 100

R373 100

R370 100

R371 100

R367 100

R368 100

R369 100

R365 100

R366 100

R361 100

R357 100

CN304
9P
D375
1SS355

Q332
DTC114EKA

C331
10
50V

C364
0.1

(Page 35)
Q341
DTA114EKA

Q340
DTC114EKA

R381 100
R350 100

D442
0

R442
10k

R382 100

R349 100

R383 100

R483 10k

R348 100

R384 100

R484 10k

R347 100

R385 100

R485 10k

R346 100

R386 100

R486 10k

R345 100

R387 100

R487 10k

R388 100

R488 10k

R344 100
D443
0
CN307
15P
FFC-S
1.25

R443
10k

(Page 41)

Q331
DTA114EKA

R455
0

R352 100

R351 100

R353 100

R355 100

R354 100

R452 10k

R451 10k

CN306
19P

R440
10k

R343 100

R389 100

R342 100

R390 100

R341 100

IC300
M3062CMEN- A14FPU0

R391 100

R340 100

R392 0
R393 0

R339 100
Q343
2SC3624

R493
0

R494 10k
R495 10k

R337 100

(Page 43)

R394 10

R395 10
R497 10k

R336 100
R335 100
Q342
2SC3624

R334 100

R397 10

R333 100

R500
10k

R332 100

CN303
19P

R400 100

X401
16MHz

R301 100

R302 100

R305 100

R304 100

R303 100

R307 100

R309 10k

R311 330k

X402 32.768KHz

C311 22p

R428
10k

R313 0

R317 10k

R321 100

R319 100

R320 4.7k

R322 100

R323 100

R326 100

C316
0.1

C310 15p

R427
10k

R318 100

D201
1SS355

R426 10k

R429
10k

R327 100

R328 100

R430
10k
CN308
19P

R306 100

CN202
7P

C267 0.1

C268
100
10V

C228
100
10V

CN201
27P

FB227

(Page 41)

FB225

IC201
NJM78M09F A

D350
10EDB40

D352
10EDB40

R418
0

IC203
TA7804LS

D304 1SS355

C301
1000
6.3V

C312
0.1

C224 100p
C223 100p
C222 100p

D204
10EDB40
D203
10EDB40

D351
10EDB40

D402
1SS355

C352
0.1
50V
C354
0.1 50V

C353
470
10V

C355
470 10V

C351
4700
16V

Q201
RT1P137S

D401
1SS355

Q202
DTC114EKA

C360
470
10V

R405
10k

D403
1SS355
IC401
M62703SL

R401
220

R402
10k

IC202
TA7807S

IC204
TA7805S

CN309
21P

C221 100p

C219 100p

R406 4.7k

D202
10EDB40

(Page 39)

D303 1SS355
D302 1SS355
D301 1SS355

C401
10 50V

C218 100p
FB216

C503
0.1

C502
0.1

C229
0.1

R403
47k

R404
47k

C230
100
10V

FB214

Q401
2SC2785

C213 47p

D404
1SS355

C236 100p
C357
470
10V

FB203

R252
1k
C234
100
10V

FB302 0

C233
0.1

R251
1k

FB201

C251
2.2
50V

D205
10EDB40

FB205

C241 0.1

R254
100k

R253
100k

(Page 45)

FB207

C232
100
10V

C240 0.1

FB301 0

(Page 33)

C235 100p

C231 0.1
C252
2.2
50V

R420 10k

C239 0.1

C356
0.1
50V

C238 0.1

C358
0.1
50V

C237 0.1

C359
100
10V

EP302

FB303 0

CN302
3P

R450
100

C451
0.1
IC450
TOTX141

C450
100 10V

(Page 45)

JW450
JW

EP301
EARTH
CN301
2P

(Page 45)

37

37

HCD-CPX11
6-8. PRINTED WIRING BOARD PRE AMP SECTION

See page 27 for Circuit Boards Location.

:Uses unleaded solder.

Semiconductor
Location

MAIN
BOARD
CN308

(Page 36)

B
MD(VIDEO)
E

R
IN

L
16

30

E
E

IC101

15

IC102

(CHASSIS)

38

38

PHONES

Ref. No.

Location

IC101
IC102

C-4
C-7

Q101
Q121
Q122
Q151
Q180
Q181
Q182
Q183
Q184
Q185

C-5
C-5
C-5
C-5
B-6
B-7
C-7
C-7
B-7
B-8

HCD-CPX11

C152
1
50V

R152
8.2k

R101
10k

C160
0.12

R133
100

R131
100

R132
100

C161
10
50V

IC101
LC75342

R102
8.2k
C141
0.1

R153
3.9k
C159
0.12

C151
220p

R151
10k

J101

C156
1
C153 C154 C155 50V
1
1
1
50V 50V 50V
C157
1
50V

C158
0.0027

6-9. SCHEMATIC DIAGRAM PRE AMP SECTION

C132
0.1

C101
220p

C131
100
10V

C109
0.12
R103
3.9k

R104 C110
1k
0.12

C108
0.0027

C106
1 50V
C107
1 50V

C105
1 50V

C104
1 50V

C102
1
50V

C103
1 50V

CN101
19P

C111
10
50V
C133
100
10V
R154
1k

Q101
2SC3624

R105
10k

R106
10k

R155
10k

R156
10k

(Page 37)
Q121
DTA114EKA

Q151
2SC3624

R173 4.7k
Q181
2SC3624

C171
10
50V

R172
100k
R171
1k

R183 C182
10k
1
50V

R182
2.7k

C181
100
10V

Q122
DTC114EKA

C172 10p
C173
10
50V

IC102
NJM4580MD

C183
100
10V

R181
2.2k

C174
220
10V

R174 22k

R122
100k

R175
47

Q180
2SC3624
C121
10
50V

R121
1k

C122 10p
C123 10 50V

R123 4.7k

EP801

R124
22k
FB894
0

C894
0.1

FB893 0

R180 4.7k

C180 220 10V

C892
0.1

Q185
DTC114EKA

C185
1
50V

C124
220
10V

FB891
0

Q183
2SC3624
R176
100k
R185
1k

R126
100k

CN102
4P

C179
100p

C129
100p

R184 1k
Q184
DTA114EKA

R125
47

Q182
2SC3624

39

39

NO804
4P

J801
C891
0.1

HCD-CPX11
6-10. PRINTED WIRING BOARD LCD/DRIVER SECTION

See page 27 for Circuit Boards Location.

:Uses unleaded solder.

(LIQUID CRYSTAL DISPLAY)

D806,D807
LCD
BACK LIGHT

IC801

C
MAIN
BOARD
CN304
(Page 36)

DRIVER BOARD

(CHUCK)

+
(TRIGGER)

(OUT)

M701
(LOADING)

IC701

1-688-337-

F
G

40

40

MAIN
BOARD
CN202
(Page 36)

HCD-CPX11
6-11. SCHEMATIC DIAGRAM LCD/DRIVER SECTION

LCD800

CN806
4P

CN807
4P

R841 470

D806
SELS6B14C
D807
SELS6B14C

R842 470
R843 470
R844 470

R851
150k
C854 0.1

R853
1k

CN805
9P

R854 10k

IC801
NJU6433F

C860
100p

C859
100p

C858
100p

C857
100p

C856
100p

R856
100

R857 100
R858 100
IC701
BA6956AN

R859 100

S703

R860
100

S701

S702

(Page 37)
CN701
7P

R702
100

D701
MTZJ-4.7C

R701
680

C711
10
50V

(Page 37)
M701

41

41

C705
0.01

HCD-CPX11
6-12. PRINTED WIRING BOARD PANEL SECTION

See page 27 for Circuit Boards Location.

:Uses unleaded solder.

Semiconductor
Location

TAPE
CD

4
(TAPE)

(TAPE)

(CD)

C
REC

E
FUNCTION
TUNER/
BAND

CD
SYNCHRO

REPEAT
FM MODE

IC802

PLAY MODE/DIRECTION
TUNING MODE

DISPLAY

E
(STAND BY)
3

E
TREBLE

(TAPE)

(CD)

TUNING

VOLUME

Location

D812
D813
D816
D818
D870

F-5
D-6
D-6
B-1
B-4

IC802

D-6

Q812
Q813
Q816
Q818
Q870

F-5
D-6
D-2
D-2
B-4

Ref. No.

DSGX

BASS

(CD)

G
MAIN
BOARD
CN303

(Page 36)

42

42

HCD-CPX11
6-13. SCHEMATIC DIAGRAM PANEL SECTION

RV805
ENCODER

RV807
ENCODER

C805
0.1

C806
0.1

R801
1k

S801

C807
0.1

C808
0.1

R802
2.2k
S803

S802

R807
1k

R808
2.2k

S810

S809

RV803
VOL ENCODER

R809
2.2k

S811

S812

C804
0.1
C803
0.1

R803
2.2k

R804
4.7k

S804

S805

R810
4.7k

R811
10k

S813

S814

R812
22k
S815

R806
2.2k

R805
1k
S806

S807

IC802
NJL24H400A

C817
47
10V

S808

R821
470

R825
47

R822
470

R828
470

R826
470

R823
470

D813
SEL5220S

D812
SEL5921A

D818
SEL5921A

D816
SEL5921A

Q812
DTC114EKA

Q813
DTC114EKA

R876
100
R875
470

Q816
DTC114EKA

R813
100

R814
100

Q818
DTC114EKA
R815
100

R874 470

R816
100

S816

NO803
4P

CN801
19P

CN802
4P

(Page 37)

43

43

D870
SEL5921A

R870
2.2k

S817

R871
4.7k

Q870
DTC114EKA

HCD-CPX11
6-14. PRINTED WIRING BOARD S-MASTER SECTION

See page 27 for Circuit Boards Location.

:Uses unleaded solder.

10

11

A
Semiconductor
Location

SUB POWER TRANSFORMER

B
1
3

AC
IN
5
4

IC610

IC600

1
E

IC604

SWITCHING
REGULATOR

IC991

MAIN
BOARD
CN301

(Page 36)

Ref. No.

Location

D611
D621
D650
D651
D652
D660
D661
D662
D670
D671
D672
D680
D681
D682
D990
D991
D992
D993
D994
D995

F-2
F-2
H-4
G-4
B-4
H-4
H-4
A-4
F-4
F-4
D-4
G-4
F-4
C-4
D-8
C-7
B-7
B-7
B-7
B-7

IC600
IC603
IC604
IC610
IC618
IC650
IC680
IC991

B-3
D-3
C-3
B-3
G-2
H-4
F-4
C-7

Q691
Q692
Q693
Q694
Q696
Q990
Q991

C-4
C-5
C-5
C-5
G-4
C-7
C-7

MAIN
BOARD
CN302

IC603

(Page 36)

1
2

(CHASSIS)

F
IC680

1
2

R
2

19

SPEAKER
IMPEDANCE
USE 4

20

4
1

IC650

(Page 36)

IC618

MAIN
BOARD
CN309

19

20

(CHASSIS)

(CHASSIS)

44

44

HCD-CPX11
6-15. SCHEMATIC DIAGRAM S-MASTER SECTION

(Page 37)

CN601
21P
IC650
CXD9750L

EP601
C674
0
C611
1
50V

C610
0.1

IC618
NJM2870F18(TE2)

C653
2.2

C660
0.01

C656
1

C663
2.2

C629
0.01

C671
0.022

TP602

FB620 0UH
FB670

C698
0.01
C600
3300
35V

D682
P6SMB36AT3

C681
0.022

C678
0.1

R652
100

TP604

FB640 0

FB652
0UH

D680
LI116V

C637 0.01

Q692
2SA1602PNP

C697
0

EP603

C675 C670
100 0.01
50V

C672 C673
100 2.2
10V

C680
0.01

C683
2.2

C640
100 10V

FB663
0UH

C689
0.01 R681
0

C692
2.2

R692
100k

R694
100k
R697
100k

C694
1

C693
2.2

Q696
2SC1623NPN

R695
100k

R696
100k

Q694
2SA1602PNP

C992
0.01
250V

NO991
2P

D991
1SS355

C618
3p

Q991
2SC3624

RY990
TYCO

R991
4.7k
R992
100k

C991
0.01
250V

X602
49.152MHz
CN600
5P

D990
1SS355
R993
4.7k

C619
3p

R620 750

C620
0.001

L604
R619 1M

IC610
MC74VHC1GU04DFT1

C679
0.01

RY991
TYCO

FB606
0

FB605 L603
0UH

C882
470p

FB662
0UH

C636
0.01

C616
22 25V
C617
0.01

R671
0

L881
JW

Q693
2SA1602PNP

TP698
TP639

CN870
2P

NO690
2P
TP671

R693
100k

FB680
0UH

TP699

C638
0.01

L871
JW

TP672

R663 100

R662
100

C639
0.01

C862
470p

R691
100k

C699
0.01

TP624

C852
470p

Q691
2SA1602PNP

C682
100
10V
C668
0.1

D672 P6SMB36AT3

D671
SFPL-62

D681 SFPL-62

R653
100

D670 LI116V

C635 0.01

C613
0

TP641

C669
0.01 R661
0

L670

C686
1

TP622

L851
JW
L861
JW

C872
470p

C676
1

FB653
0UH

CN850
2P

TP652
C666
1

R623 100k

C630 0.1

C652
100
10V

NO691
2P

R651
C659
0
0.01

IC680
CXD9750L

IC600
CXD9743N

R641 100
FB641 0

R642 100

R615
470
C615
10p

FB642 0

R614 1M

C654
0.01

C690
0.01

C634 0.01

R612
100

R613
100

TP651

L650

C632
100
10V

C633
0.01

L602

C650
0.1

C649
100 10V

FB650
0UH

L890

FB610 0UH
FB660
0

50V
C631 4.7

FB604 0

C607 0.1

C612
0.1

D661 SFPL-62V

LP850
MT

R610 100

C623
100p

IC603
PCM1802DBR

IC604
TC7WU04F

D662
P6SMB36AT3

TP717

C655
100
50V

C608 10 50V

D660
LI116V

C648
0.1

TP903

R640
100

TP904

C625
4.7
50V

50V

C605
0.1

C651
0.022

C661 0.022

D651
SFPL-62V
C609
0.001
R609 100

L601

X601
12.288MHz
C614
10p

D650 LI116V

TP905

TP907

TP910

TP908

TP909

R603 100

R602 100

R601 100

TP914

TP912

TP913
R606 100

R604 100

R618
0

TP901

FB601
0

C628 4.7

R605 1k

C603
0.1

C606 0.1

C602
10
50V

C622 0.1

C604
0.1

TP916

TP918

C601
100 10V

R607 100

D611
1SS355

L621

C621
1 50V

TP917

TP919
D621
1SS355

D652 P6SMB36AT3

TP921

D992
10EDB40

TP981

D995
10EDB40

Q990
2SC3624

IC991
NJU7201L40

TP636
FB607 0

R994
100k
TP991

R608 0

D994
10EDB40
CN990
2P

TP982

T991
SUB POWER
TRANSFORMER

D993
10EDB40

C993
2200
16V

C994
100
10V

NO992
3P

TP992
TP993

(Page 37)

45

45

J860

HCD-CPX11

IC BLOCK DIAGRAMS

Waveforms
BD81A Board

S-MASTER AMP Board

BD81A Board

IC101 ra (RFACO)
(CD play mode)

IC300 qa (XCOUT)

IC603 q; (LRCK)
IC301 TC94A34FG-002
CKI

VDD

TXO

SFSY

SBSY

DATA

PIO3

VSS

PIO4

PIO0

PIO5

PIO1

PIO6

DIT

Audio I/F

11 SDO0

round & limit

ALU
A2

10 VSS

round & limit

A1

9 VDDT

A0

ERAM
2k word

SRMSTB 41

A3

AY

CRAM
4k word

VDDM 40

MAC

27.3 s

20 s/DIV 2 V/DIV

12 BCKO

AX

AD11 39

14 SDI0

13 LRCKO

MZ

AD12 38

40 ns/DIV 1 V/DIV

15 BCKIA

8 MIACK

VDDT 42

MCU. I/F

YRAM
4k word

7 MICK

6 MIDIO

Program
Control

XRAM
4k word

AD10 43

AD9 44
Bus
Switch

5 MILP

AD8 45

PRAM

POM

AD7 46

Instruction
Decoder

4 MICS

3 STANBY

AD6 47

2 RESET

AD5 48

46

46

1 VDDP

Timing
Generator

49

50

51

52

53

54

55

56

57

58

59

60

61

62

63

64

AD1

AD0

VSS

VDD

CKO

VDDX

XO

XI

VSSX

TEST

MIMD

VSSP

VCOI

VC0

AD2

10 s/DIV 5 V/DIV

17

AD3

12.4 Vp-p

18

X-Pointer
register

81.3 ns

3.6 Vp-p

12.2 s

19

CROM
4k word

IC801 ts (OSC2)

20

AD4

CDP Cont
I/F

LCD Board

Q642, 643 (Collector)

(REC mode)

PIO2

PIO7

BUCK 36

IC604 6 (3A)

3 Vp-p

21

16 LRCKIA

CCE 37

TC Board

22

MY

100 ns/DIV 2 V/DIV

23

MX

OE 35

326 ns

40 ns/DIV 1 V/DIV

24

register
XO X1 X2
Y0 Y1 Y2

40 ns/DIV 1 V/DIV

25

Y-Bus

2.7 Vp-p
62.5 ns

26

1Mbit
SRAM

IC603 qa (BCK)
CAS 34

1.9 Vp-p

27

RAS 33

4.2 Vp-p

59.1 ns

28

X-Bus

29

C-Pointer
register

IC300 qd (XOUT)

30

Y-Pointer
register

10 s/DIV 2 V/DIV

31

SRAM I/F

IC101 uj (XTAO)

20 s/DIV 1 V/DIV

32

Address Calc.
2sets

20.7 s

General
In/Output Port

1 s/DIV 200 mV/DIV

3.1 Vp-p

SRAM/
DRAM I/F

30.5 s

0.9 0.4 Vp-p

WE

5 Vp-p

Sub code
I/F

MAIN Board

HCD-CPX11

IC251 BA5947FM

CH4OUTR 19

CH4OUTF 20

CH3OUTF 21

19k

CH3OUTR 22

PIN26
6.5k

POW
VCC
(ch3, 4)

POWVCC 23
MUTE 24

LEVEL
SHIFT

10k

Vref

18 CH1PUTF

17 CH1OUTR

16 CH2OUTF

15 CH2OUTR

POW
VCC
(ch1, 2)

50k 50k

50k 50k

POW
VCC

14 POWVCC
13 CNF4

50k 50k

GND 25
MUTE

GND 26

12 GND

Vref

11 C-M
10 C-P

PREGND 27
CT 28

CH3FIN 30

CH4CAPA 32
OUTVREF 33

CH3RIN 29

CH4IN 31

R
R
INTER
FACE F

INTER
FACE
F

100k

7 CH2FIN

5 CH1FIN

10k
50k

8 CH2RIN

6 CH1RIN

INTER
FACE

PIN3

9 VG

SW

4 SW
3 OPIN+

DPOUT 34
Pre
Vcc

TREVCC 35

2 OPIN-

NC 36

1 NC

PRE AMP Board

VDD

VREF

NC

ROUT

RBASS2

RBASS1

RTRE

RSELO

R4
R3
R2
R1

NC

30

29

28

27

26

25

24

23 22 21

20 19 18 17

16

RIN

CL

IC101 LC75342

LVREF

CONTROL
CIRCUIT

LOGIC
CIRCUIT

CCB
INTERFACE

CONTROL
CIRCUIT

RVREF

10

11 12 13 14

15

VSS

LOUT

LBASS2

LBASS1

LTRE

LIN

LSELO

L4
L3
L2
L1

NC

CE

TEST

DI

47

HCD-CPX11

DRIVER Board
IC701 BA6956AN

TSD

CONTROL LOGIC

RIN

GND

VCC

OUT1

OUT2

FIN

VM

RNF

VREF

S-MASTER AMP Board

42 41 40 39 38

37 36 35 34 33 32 31 30 29 28 27 26 25

PWM

LINER
INTERPOLATOR
(2 TIMES)

FSOCKO

FSOI

SFLAGO

TEST2

TEST1

HPOUTR2

HPVSSR

HPOUTR1

HPVDDR

HPOUTL2

HPVSSL

HPOUTL1

HPVDDL

XVSS

XFSOIN

XVDD

VSUBC

OUTR2

VSSR

OUTR1

VDDR

IC600 CXD9743N

24 23 22

GAIN
CONTROL

DF2

DF1

SgP

RATE
CONVERTER

11 12 13

14 15

16 17 18 19 20 21

SCDT
SCSHIFT
SCLATCH

NSPMUTE
INIT

LRCK
BCK
DATA

VIN

VOUT

THERMAL
PROTECTION

CONTROL

GND

NOISE
BYPASS

BANDGAP
REFERENCE

XFSIIN

10

BFVDD
BFVSS

7 8 9

MCKSEL

CLOCK
GENERATOR
(PRIMARY)

IC618 NJM2870F18 (TE2)

48

INIT/
MUTE

XOVSS
DVDD
DVSS

VDDL
OUTL1
VSSL
OUTL2
XOVDD

1 2 3 4 5

SERIAL
CONTROL

XFSOOUT

CLOCK
GENERATOR
(SECONDARY)

HCD-CPX11

IC650, 680

VBBA 1

CXD9750L

VBBA

VBOOTA 2
VDRVA 3

VDRVA
UNDER
VOLTAGE
LOCKOUT

VDDA 4
GNDA 5

THERMAL
SHUT DOWN

INA 6
ENA 7
DIAGA 8

PROTECTOR
CIRCUIT
CROSS OVER
DELAY

LOW SIDE
LEVEL SHIFT

HIGH SIDE
LEVEL SHIFT

PRE
DRIVER

PRE
DRIVER

FILTER

+
+-

VBBA

VDRVA

VBBA

OUTA 9
SA 10
VBBB 11

VBBB

VBOOTB 12
VDRVB 13

VDRVB
UNDER
VOLTAGE
LOCKOUT

VDDB 14
GNDB 15

THERMAL
SHUT DOWN

INB 16
ENB 17
DIAGB 18

PROTECTOR
CIRCUIT
CROSS OVER
DELAY

LOW SIDE
LEVEL SHIFT

HIGH SIDE
LEVEL SHIFT

PRE
DRIVER

PRE
DRIVER

FILTER

+
+-

VBBB

VDRVB

VBBB

OUTB 19
SB 20

49

HCD-CPX11

IC603 PCM1802DBR

VINL

VINR

VREF1

VREF2

SINGLE-END/
DIFFERENTIAL
CONVERTER

5TH ORDER
DELTA-SIGMA
MODULATOR
x16 1/64
(x1/128)
DECIMATION
FILTER
WITH
DC CUT
FILTER

REFERENCE

SINGLE-END/
DIFFERENTIAL
CONVERTER
VCC
AGND

5
6

20
19
18
17
16
15
14
13
12
11

SERIAL
INTERFACE
&
MODE/FORMAT
CONTROL

5TH ORDER
DELTA-SIGMA
MODULATOR

MODE1
MODE0
FMT1
FMT0
OSR
SCKI
VDD
DGND
DOUT
BCK

POWER
SUPPLY
CLOCK & TIMING CONTROL

PDWN 7
BYPAS 8
FSYNC 9
LRCK 10

LCD Board

SEG33 - 48

IC801 NJU6433F

49

SEG49

50

SEG50

51

OSC1

52

OSC2

53

VDD

54

VSS

55

VLCD

56

CE

57

SCL

58

DATA

59

MODE

60

INH

61

COM4

62

COM3

63

COM2

64

33 - 48

COM1

Latch Circuit / Segment Driver

Oscillation
Circuit

SEG17 - 32

Input
Select

Shift
Register3
50-Bit

Input
Select

Shift
Register2
50-Bit

Input
Select

Shift
Register1
50-Bit

Input
Select

17 - 32

Shift
Register4
50-Bit

Dividing
Circuit

Shift Register
Control Circuit

Input Select Circuit

Decoder

Common
Driver

SEG1 - 16

16 - 1

50

HCD-CPX11

6-16. IC PIN FUNCTION DESCRIPTION

BD81A BOARD IC101 CXD3059AR (RF AMP)
Pin No.

Pin Name

I/O

MIRR

I/O

Mirror signal input/output (Not used)

Description

DFCT

I/O

Defect signal input/output (Not used)

FOK

I/O

Focus OK signal input/output (Not used)

VSS

Internal digital ground

LOCK

I/O

MDP

Spindle motor servo control output

SSTP

Disk innermost detection signal input

IOVSS1

I/O digital ground

SFDR

Sled drive output

10

SRDR

Sled drive output

11

TFDR

Tracking drive output

12

TRDR

Tracking drive output

13

FFDR

Focus drive output

14

FRDR

Focus drive output

15

IOVDD1

I/O digital power supply

16

AVDD0

Analog power supply

17

AVSS0

Analog ground

18

NC

Not used

19

E signal input

20

F signal input

21

TEI

Tracking error signal input to DSSP block

22

TEO

Tracking error signal output from RF amplifier block

GFS is sampled at 460Hz; when GFS is high , this pin outputs a high signal
If GFS is low eight consecutive

23

FEI

Focus error signal input to DSSP block

24

FEO

Focus error signal output from RF amplifier block

25

VC

I/O

26

A signal input

27

B signal input

28

C signal input

29

D signal input

Center voltage output from RF amplifier block

30

NC

Not used

31

AVDD4

Analog power supply

32

RFDCO

RFDC signal output (Not used)

33

PDSENS

Reference voltage pin for PD

34

AC_SUM

RFAC summing amplifier output

35

EQ_IN

Equalizer circuit input

36

LD

APC amplifier output

37

PD

38

NC

APC amplifier input

Not used

39

RFC

40

AVSS4

Analog ground

Equalizer cut-off frequency adjustment pin

41

RFACO

RFAC signal output

42

RFACI

RFAC signal input or EFM signal input

43

AVDD3

44

BIAS

Asymmetry circuit constant current input

45

ASYI

Asymmetry comparator voltage input

46

ASYO

EFM full-swing output (Low = VSS, High = VDD)

Analog power supply

51

HCD-CPX11

Pin No.

Pin Name

I/O

47

VPCO

52

Description
Wide-band EFM PLL charge pump output (Not used)

48

VCTL

49

AVSS3

Wide-band EFM PLL VCO2 control voltage input

50

CLTV

51

FILO

Master PLL (slave = digital PLL) filter output

52

FILI

Master PLL filter input

Analog ground
Multiplier VCO1 control voltage input

53

PCO

Master PLL charge pump output

54

AVDD5

Analog power supply

55

DDVROUT

DC/DC converter output

56

DDVRSEN

DC/DC converter output voltage monitor pin

57

AVSS5

58

DDCR

59

NC

Analog ground
DC/DC converter reset pin
Not used

60

BCKI

D/A interface bit clock input

61

PCMDI

D/A interface serial data input (2s COMP, MSB first)

62

LRCKl

D/A interface LR clock input

63

LRCK

D/A interface LR clock output f = Fs

64

VSS

Internal digital ground

65

PCMD

D/A interface serial data output (2s COMP, MSB first)

66

BCK

D/A interface bit clock output

67

VDD

Internal digital power supply

68

EMPH

High when the playback disc has emphasis, low it has not

69

EMPHI

High when de-emphasis is ON, low when input OFF

70

IOVDD2

I/O digital power supply

71

DOUT

Digital Out output

72

TEST

Test pin Normally ground

73

TES1

Test pin Normally ground

74

IOVss2

I/O digital ground

75

NC

Not used

76

XVSS

Master clock ground

77

XTAO

Crystal oscillation circuit output

78

XTAI

Crystal oscillation circuit input

79

XVDD

Master clock power supply

80

AVDD1

Analog power supply

81

AOUT1

Lch analog output

82

VREFL

Lch reference voltage

83

AVSS1

Analog ground

84

AVSS2

Analog ground

85

VREFR

Rch reference voltage

86

AOUT2

Rch analog output

87

AVDD2

Analog power supply

88

NC

Not used

89

IOVDD0

I/O digital power supply

90

RMUT

Rch 0 detection flag (Not used)

91

LMUT

Lch 0 detection flag (Not used)

92

NC

Not used

93

XTSL

Crystal selection input (Not used)

HCD-CPX11

Pin No.

Pin Name

I/O

94

IOVSS0

Description

95

XTACN

96

SQSO

97

SQCK

98

SBSO

Subcode P to W serial output

99

EXCK

SBSO readout clock input

I/O digital ground

Oscillation circuit control
Self-oscillation when high, oscillation stop when low
Subcode Q 80-bit and PCM peak and level data output
CD TEXT data output
SQSO readout clock input

100

XRST

System reset Reset when low

101

SYSM

Mute input Muted when high

102

D ATA

Serial data input from CPU

103

VSS

104

XLAT

105

CLOCK

106

VDD

Internal digital power supply

107

SENS

SENS output to CPU

108

SCLK

SENS serial data readout clock input

109

ATSK

I/O

Anti-shock input/output (Not used)

110

WFCK

WFCK output (Not used)

111

XUGF

XUGF output (Not used)

112

XPCK

XPCK output (Not used)

113

GFS

GFS output (Not used)

114

C2PO

C2PO output (Not used)

115

SCOR

High output when the subcode sync, S0 or S1, is detected

116

VDD

Internal digital power supply

117

C4M

4 2336MHz output (Not used)

118

WDCK

Word clock output f = 2Fs (Not used)

119

COUT

I/O

Track number count signal input/output (Not used)

120

NC

Not used

Internal digital ground

Latch input from CPU The serial data is latched at the falling edge
Serial data transfer clock input from CPU

53

HCD-CPX11

MAIN BOARD IC300 M3062CMEN-A14FPU0 (SYSTEM CONTROLLER)

Pin No.

Pin Name

I/O

Description

MILP

CS signal output to the digital signal processor

MP3 REQ

REQ output to CD digital processor signal output

MIACK

ACK input from CD digital processor input

SIRCS IN/WAKE

Remote control signal input terminal

MP3 DATA OUT

Serial data output to MP3

MP3 DATA IN

Serial data input from MP3

MP3 CLK

Serial data transfersignal output to MP3

BYTE

Not used
Ground terminal

CNVSS

10

XCIN

Sub system clock input terminal (32.768 kHz)

11

XCOUT

Sub system clock output terminal (32.768 kHz)

12

RESET

13

XOUT

14

VSS

15

XIN

16

VCC

17

NMI

Non-maskable interrupt input terminal

18

RDS CLK

Serial data transfer clock signal input from the RDS decoder

19

CD SCOR

Subcode sync (S0+S1) detection signal input from the digital signal processor

20

AC CUT

AC off detection signal input from the reset signal generator L: AC cut checked

21

MP3 RST

RESET output to CD digital processor

22

MICS

CS output to the CD digital processor

23

MP3 STB

MP3 STB output signal

System reset signal input from the reset signal generator

L: reset

For several hundreds msec. after the power supply rises, L is input,
then it changes to H

54

Main system clock output terminal (16 MHz)

Ground terminal
Main system clock input terminal (16 MHz)
Power supply terminal (+3.3V)
Not used

24

CDM LOAD-IN

Motor drive signal (close direction) output terminal

25

CDM LOAD-OUT

Motor drive signal (open direction) output terminal

26

CDM SW3

Loading in/out detect switch input terminal

L: loading in

27

CDM SW1

Loading in/out detect switch input terminal

L: loading in

28

CDM SW2

Loading in/out detect switch input terminal

L: loading in

Not used

29

IIC CLK

I/O

Communication data transfer clock signal input/output terminal

30

IIC DATA

I/O

Communication data bus terminal

31

NO USE

Not used

32

CD SENS

Not used

Not used

Internal status detection monitor input from the digital signal processor

33

CD XRST

Reset signal output to the digital signal processor and motor/coil driver L: reset

34

CD XTCN

CD XTCN signal output

35

CD DATA

Serial data output to the digital signal processor

36

CD XLT

Serial data latch pulse signal output to the digital signal processor

37

CD CLK

Serial data transfer clock signal output to the digital signal processor

38

CD BD-PWR

Power supply on/off control signal output for the CD section

39

PWR RELAY

Main system power supply on/off control signal output terminal

40

DIAG

Protect signal input from the power amplifier and protect detect circuit

41

ENA

Output enable control signal output to the power amplifier

42

SC DT

Serial data output to the digital audio signal processor

43

SC SHIFT

Serial data shift clock signal output to the digital audio signal processor

44

SC LATCH

Serial data latch pulse signal output to the digital audio signal processor

H: power on
H: power on

HCD-CPX11

Pin No.

Pin Name

I/O

Description
Muting on/off control signal output to the digital audio signal processor

45

NSP MUTE

46

INIT

Reset signal output to the digital audio signal processor

47

ST CLK

PLL serial data transfer clock signal output to the tuner unit

L: muting on
L: reset

48

ST DATA IN

PLL serial data input from the tuner unit

49

ST DATA OUT

PLL serial data output to the tuner unit

50

ST CE

PLL chip enable signal output to the tuner unit

51

ST TUNED

Tuning detection signal input from the tuner unit

52

ST STEREO

FM stereo detection signal input from the tuner unit

53

ST MUTE

Tuner muting on/off control signal output to the tuner unit

54

RDS DATA

Serial data input from the RDS decoder

L: tuned
L: stereo
H: muting on

55

EQ CLK

Serial data transfer clock signal output to the electrical volume

56

NO USE

Not used

57

EQ CE

Chip enable signal output to the electrical volume

58

HP MUTE

Headphone muting on/off control signal output terminal

59

LINE MUTE

Audio line muting on/off control signal output terminal

60

CD MUTE

CD analog signal muting on/off control signal output terminal

61

TC ALC

62

VCC

Power supply terminal (+3.3V)

63

SOFT TEST

Output terminal for the software test

64

VSS

Ground terminal

65

TC REC/MUTE

H: muting on
H: muting on
H: muting on

Automatic limiter control signal output to the recording/playback equalizer

amplifier

H: limiter on
Not used

Recording muting on/off control signal output to the recording/playback equalizer

amplifier

L: muting on

Line muting on/off control signal output to the recording/playback equalizer

66

TC LINE MUTE

67

TC PB/REC

Recording/playback selection signal output terminal L: playback, H: recording

68

TC BIAS-ON

Recording bias on/off control signal output terminal

69

TC PLAY SW

Head position detect switch input terminal

70

TC CAPM-CONT

Capstan/reel motor on/off control signal output terminal

amplifier

H: muting on

71

TC TRG

Trigger plunger on/off control signal output terminal

72

LCD INH

Reset signal output to the liquid crystal display driver

73

LCD MODE

H: bias on
H: motor on

H: plunger on
L: reset

Signal output for discriminating between command and display data to the liquid
crystal display driver

L: display data, H: command

74

KEY WAKE UP

System wake up signal input by pressing any key

75

LCD DATA/EQ DATA

Serial data output to the liquid crystal display driver

76

LCD SCL

Serial data transfer clock signal output to the liquid crystal display driver

77

LCD CE

Chip select signal output to the liquid crystal display driver

L active

78

LCD ON/LCD BL

Power on/off control signal output for liquid crystal display

H: power on

79

LED TC

LED drive signal output of the TAPE nN indicator

80

LED TUNER

LED drive signal output of the TUNER BAND indicator

81

LED STANDBY

LED drive signal output of the standby indicator

82

LED DSG

LED drive signal output of the DSG indicator

83

TRE A

Jog dial pulse input from the rotary encoder (TREBLE) (A phase input)

84

TRE B

Jog dial pulse input from the rotary encoder (TREBLE) (B phase input)

85

BASS A

Jog dial pulse input from the rotary encoder (BASS) (A phase input)

H: LED on
H: LED on

H: LED on

H: LED on

55

HCD-CPX11

Pin No.

Pin Name

I/O

86

BASS B

Jog dial pulse input from the rotary encoder (BASS) (B phase input)

Description

87

VOL A

Jog dial pulse input from the rotary encoder (VOLUME) (A phase input)

88

VOL B

Jog dial pulse input from the rotary encoder (VOLUME) (B phase input)

89

LED CD

LED drive signal output of the CD NX indicator

90

TC END SW

Tape end detect switch input terminal

91

TC HALF/REC/SW

92

MODEL

Model setting terminal

Recording-proof claw (forward/reverse) detect switch and cassette in detect

switch input terminal (A/D input)

93

DEST

Destination setting terminal

94, 95

KEY3, KEY2

Front panel key input terminal (A/D input)

96

AVSS

56

Ground terminal (for analog system)

97

KEY1

Front panel key input terminal (A/D input)

98

VREF

Reference voltage (+3.3V) input terminal

99

AVCC

100

HP DET

H: LED on

Power supply terminal (+3.3V) (for analog system)

Headphone jack connection detection signal input terminal
L: no connected, H: headphone connected

HCD-CPX11
SECTION 7
EXPLODED VIEWS
NOTE:
-XX and -X mean standardized parts, so they
may have some difference from the original
one.
Items marked * are not stocked since they
are seldom required for routine service.
Some delay should be anticipated when
ordering these items.

7-1.

The mechanical parts with no reference

number in the exploded views are not supplied.
Abbreviation
AUS : Australian model
KR
: Korean model

The components identified by mark 0 or

dotted line with mark 0 are critical for safety.
Replace only with part number specified.

MAIN SECTION
2

#1

1
1

chassis section

#1
front panel section

#1
#1

Ref. No.
1
2
#1

Part No.

Description

Remark

4-235-099-11 SCREW (CASE 3 TP2)

4-244-016-21 COVER
7-685-645-79 SCREW +BVTP 3X6 TYPE2 TT (B)

57

HCD-CPX11

7-2.

FRONT PANEL SECTION

60
61

71

62
lid (TC) section

#2

61
#2

not
supplied

56

70

58

67

63

57

not
supplied

59

55
59
54
64
69
65
66

53

59
not
supplied

52

59
not
supplied

51

Ref. No.

68

Part No.

Description

51
52
53
54
55

4-252-359-01
4-252-348-01
4-252-349-01
4-252-352-01
X-4956-171-1

KNOB, TUNING
KNOB, VOLUME
KNOB, BASS
BAND (UPPER), DIVISION
PANEL ASSY, FRONT (AEP, UK)

55
56
57
58
59

X-4956-181-1
4-244-021-01
4-244-023-01
4-244-014-01
4-951-620-01

PANEL ASSY, FRONT (KR, AUS)

SPRING (LID TC), TORSION
SPRING (EJECT), COMPRESSION
LEVER (EJECT)
SCREW (2.6X8), +BVTP

60
61

1-824-192-11 WIRE (FLAT TYPE) (8 CORE)

3-669-480-51 + PTPWH 2

58

Remark

Ref. No.

Part No.

Description

62
63
64
65
66

A-4750-369-A
1-796-456-31
A-4750-358-A
4-933-134-11
4-244-530-01

TC BOARD, COMPLETE
DECK, MECHANICAL (CMAL1Z-236A)
PANEL BOARD, COMPLETE
SCREW (+PTPWH M2.6X8)
DAMPER

67
68
69
70
71

4-252-396-01
4-233-372-02
1-773-120-11
4-951-620-31
1-773-110-11

PLATE (TOP), ORNAMENT

FOOT (FELT)
WIRE (FLAT TYPE) (19 CORE)
SCREW (2.6), +BVTP
WIRE (FLAT TYPE) (19 CORE)

#2

7-685-646-79 SCREW +BVTP 3X8 TYPE2 TT (B)

Remark

HCD-CPX11

7-3.

LID (TC) SECTION

105

104

not
supplied

104

106

103
101
102
not
supplied

not
supplied

LCD800

Ref. No.
101
102
103
104

Part No.

Description

X-4956-169-1
1-769-912-11
1-861-335-11
4-951-620-01

LID (TC) ASSY

WIRE (FLAT TYPE) (9 CORE)
LCD BOARD
SCREW (2.6X8), +BVTP

Remark

Ref. No.

Part No.

Description

Remark

105
4-244-022-01 SPRING (TC), LEAF
106
4-252-353-01 HOLDER (TC)
LCD800 1-805-545-11 DISPLAY PANEL, LIQUID CRYSTAL

59

HCD-CPX11

7-4.

CHASSIS SECTION

S-MASTER AMP section

154

#1

153
158
#1
#1
not
supplied

#1

155

151

CD mchanism deck section

156
152
#1

#1

#1

#1
not
supplied

157
#3

Ref. No.

Part No.

Description

0 151
0 151
0 151
152
153

1-769-079-23
1-777-071-83
1-783-203-13
3-703-244-00
A-4750-356-A

CORD, POWER (KR)

CORD, POWER (AEP, UK)
CORD, POWER (AUS)
BUSHING (2104), CORD
PRE AMP BOARD, COMPLETE

154
154
155

A-4750-353-A MAIN BOARD, COMPLETE (AEP, UK)

A-4750-940-A MAIN BOARD, COMPLETE (KR, AUS)
1-777-353-11 FLAT CABLE (15 CORE) (AEP, UK)

Remark

Ref. No.

Part No.

Description

Remark

155
156
156
156
157

1-824-486-11
1-693-603-31
1-693-604-11
1-693-605-11
4-233-372-02

WIRE (FLAT TYPE) (11 CORE) (KR, AUS)

TUNER (FM/AM) (AUS)
TUNER (FM/AM) (AEP, UK)
TUNER (FM/AM) (KR)
FOOT (FELT)

158
#1
#3

1-773-105-11 WIRE (FLAT TYPE) (19 CORE)

7-685-645-79 SCREW +BVTP 3X6 TYPE2 TT (B)
7-685-647-79 SCREW +BVTP 3X10 TYPE2 TT (B)
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part number specified.

60

HCD-CPX11

7-5.

S-MASTER AMP SECTION

not
supplied

#1

#1

201
#1
#1
#1
#2

#1

202
203
not
supplied
not
supplied

#1

204
#1

not
supplied

not
supplied

Ref. No.

Part No.

Description

0 201
202
203

1-468-730-11 REGULATOR, SWITCHING

A-4750-366-A S-MASTER AMP BOARD, COMPLETE
1-500-484-21 CLAMP, SLEEVE FERRITE

Remark

Ref. No.
204
#1
#2

Part No.

Description

Remark

1-773-158-11 WIRE (FLAT TYPE) (21 CORE)

7-685-645-79 SCREW +BVTP 3X6 TYPE2 TT (B)
7-685-646-79 SCREW +BVTP 3X8 TYPE2 TT (B)

The components identified by mark 0 or dotted

line with mark 0 are critical for safety.
Replace only with part number specified.

61

HCD-CPX11

7-6.

CD MECHANISM DECK SECTION-1

(CDM80BH-F1BD81)
410
411

410

410

#9

412
410

CD mechanism deck section-2

(CDM80BH-F1BD81)

407

413
401

not
supplied

409

408

a
M701

406

405

CD mechanism deck section-3

(CDM80BH-F1BD81)

401
404

b
a

403

base unit section

(BU-F1BD81A)

not
supplied

401

Ref. No.

Part No.

Description

401
403
404
405
406

4-985-672-01
4-245-653-01
4-245-662-02
4-245-646-01
4-245-644-01

SCREW (+PTPWHM2.6), FLOATING

BELT (MOT)
PULLEY (GEAR)
GEAR (IDL-F)
GEAR (IDL-D)

407
408

4-245-645-01 GEAR (IDL-E)

4-246-203-01 LEVER (RELEASE)

62

Remark

Ref. No.

Part No.

Description

409
410
411
412
413

4-245-630-01
4-951-620-01
4-245-639-01
1-688-337-11
1-763-967-11

LEVER (SW)
SCREW (2.6X8), +BVTP
LEVER (CL UP2)
DRIVER BOARD
MOTOR, DC

M701
#9

X-2021-530-1 MOTOR (PULLEY) ASSY (LOADING)

7-685-106-19 SCREW +P 2X10 TYPE2 NON-SLIT

Remark

HCD-CPX11

7-7.

CD MECHANISM DECK SECTION-2

(CDM80BH-F1BD81)

464
463

462
461
465

460
459
458

466

467

457

468

455
456
456

455

469

454
453
470
452
451

453
452
451

Ref. No.

Part No.

Description

451
452
453
454
455

4-245-627-01
4-245-637-01
4-245-649-01
4-245-657-01
4-245-647-01

WASHER (6-2.7-0.4)
ROLLER, RUBBER
GEAR (IDL-I)
LEVER (LOADING-R)
GEAR (IDL-G)

456
457
458
459
460

4-245-648-01
4-245-655-01
4-245-631-01
4-245-650-01
4-245-651-01

GEAR (IDL-H)
CHASSIS (TOP)
SPR-T (LOADING-R)
GEAR (IDL-J)
GEAR (IDL-L)

Remark

Ref. No.

Part No.

Description

461
462
463
464
465

4-245-640-01
1-452-925-21
4-245-638-01
4-985-672-01
4-245-636-01

GEAR (CAP)
MAGNET ASSY
LEVER (CL UP1)
SCREW (+PTPWHM2.6), FLOATING
SPR-T CL DOWN

466
467
468
469
470

4-245-658-01
4-245-659-01
4-245-632-01
X-2021-532-1
4-245-656-01

LEVER (DISC STOP)

LEVER (DISC SENSOR)
SPR-T (LOADING-L)
CLAMPER 213 ASSY
LEVER (LOADING-L)

Remark

63

HCD-CPX11

7-8.

CD MECHANISM DECK SECTION-3

(CDM80BH-F1BD81)

510
509
508
507
511
506
512
505

513
504

509
514
not
supplied

503

502
515
not
supplied

501
not
supplied

Ref. No.

Part No.

Description

501
502
503
504
505

4-245-643-01
X-4956-147-1
4-248-722-01
4-245-642-01
4-245-814-01

GEAR (IDL-C)
CHASSIS (BOTTOM) ASSY
SPR-E, DIR
GEAR (IDL-B)
LEVER (DIR FIRST)

506
507
508

4-245-633-01 SPR-E DIR BACK

4-245-660-01 LEVER (DIR)
4-245-641-01 GEAR (IDL-A)

64

Remark

Ref. No.

Part No.

Description

509
510
511
512
513

4-245-640-01
4-245-628-01
4-248-206-01
4-245-624-01
4-245-635-01

GEAR (CAP)
LEVER (BU LOCK)
WASHER (3-1-0.4)
LEVER, CLOSE
SPR-E LEVER CLOSE

514
515

4-245-629-01 GEAR (BU LOCK)

4-245-644-01 GEAR (IDL-D)

Remark

HCD-CPX11

7-9.

BASE UNIT SECTION (BU-F1BD81A)

558

555
559
554
556

560

555

555

554
554
560

553

555

552
554
553
552

551

557
not
supplied

552

Ref. No.
551
552
553
554
555

Part No.

Description

A-4751-431-A
4-951-620-01
4-231-151-01
4-227-045-31
4-227-549-11

BD81A BOARD, COMPLETE

SCREW (2.6X8), +BVTP
STOPPER (BU)
SPRING (INSULATOR), COIL
INSULATOR

Remark

not supplied

Ref. No.

Part No.

Description

Remark

0 556
557
558
559
560

8-820-244-01
1-775-241-11
X-4956-146-1
1-827-992-11
4-985-672-01

OPTICAL PICK-UP (KSM-215DCP/C2NP)

WIRE (FLAT TYPE) (27 CORE)
HOLDER (BU215) ASSY
WIRE (FLAT TYPE)(16 CORE)
SCREW (+PTPWHM2.6), FLOATING

The components identified by mark 0 or dotted

line with mark 0 are critical for safety.
Replace only with part number specified.

65

HCD-CPX11
BACK LIGHT

SECTION 8
ELECTRICAL PARTS LIST

BD81A

NOTE:
Due to standardization, replacements in the
parts list may be different from the parts
specified in the diagrams or the components
used on the set.
-XX and -X mean standardized parts, so they
may have some difference from the original
one.
RESISTORS
All resistors are in ohms.
METAL: Metal-film resistor.
METAL OXIDE: Metal oxide-film resistor.
F: nonflammable
CAPACITORS
uF: F
COILS
uH: H
Ref. No.

Part No.

Items marked * are not stocked since they

are seldom required for routine service.
Some delay should be anticipated when
ordering these items.
SEMICONDUCTORS
In each case, u: , for example:
uA. . : A. .
uPA. . : PA. .
uPB. . : PB. .
uPC. . : PC. .
uPD. . : PD. .
Accessories are given in the last of this parts
list.
Abbreviation
AUS : Australian model
KR
: Korean model

Description

Remark

BACK LIGHT BOARD

****************
< CONNECTOR >
CN807

1-770-011-41 CONNECTOR, BOARD TO BOARD 4P

Ref. No.

Part No.

When indicating parts by reference number,

please include the board name.
The components identified by mark 0 or
dotted line with mark 0 are critical for safety.
Replace only with part number specified.

Description

Remark

C172

1-162-920-11 CERAMIC CHIP

27PF

5%

50V

C174
C181
C182
C183
C184

1-164-360-11
1-164-360-11
1-164-360-11
1-124-778-00
1-124-778-00

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
ELECT CHIP

0.1uF
0.1uF
0.1uF
22uF
22uF

20%
20%

16V
16V
16V
6.3V
6.3V

C185
C186
C194
C195
C196

1-164-315-11
1-164-315-11
1-164-360-11
1-164-360-11
1-164-360-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

470PF
470PF
0.1uF
0.1uF
0.1uF

5%
5%

50V
50V
16V
16V
16V

C201
C203
C209
C210
C211

1-128-995-21
1-128-995-21
1-162-970-11
1-107-826-11
1-164-230-11

ELECT CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

100uF
100uF
0.01uF
0.1uF
220PF

20%
20%
10%
10%
5%

10V
10V
25V
16V
50V

C212
C213
C251
C252
C255

1-162-919-11
1-162-919-11
1-162-969-11
1-164-360-11
1-164-360-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

22PF
5%
22PF
5%
0.0068uF 10%
0.1uF
0.1uF

50V
50V
25V
16V
16V

C257
C258
C259
C260
C302

1-164-360-11
1-164-360-11
1-164-360-11
1-128-394-11
1-164-360-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP

0.1uF
0.1uF
0.1uF
220uF
0.1uF

16V
16V
16V
10V
16V

C303
C305
C306
C307
C308

1-164-360-11
1-126-246-11
1-164-360-11
1-164-360-11
1-126-208-21

CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP

0.1uF
220uF
0.1uF
0.1uF
47uF

C309
C310
C311
C312
C313

1-164-360-11
1-164-360-11
1-164-360-11
1-164-360-11
1-164-360-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

0.1uF
0.1uF
0.1uF
0.1uF
0.1uF

C314
C315
C316
C317
C318

1-126-208-21
1-107-826-11
1-162-966-11
1-162-970-11
1-162-970-11

ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

47uF
0.1uF
0.0022uF
0.01uF
0.01uF

C320

1-216-864-11 SHORT CHIP

< DIODE >

D806
8-719-075-50 DIODE SELS6B14C-TP5 (LCD BACK LIGHT)
D807
8-719-075-50 DIODE SELS6B14C-TP5 (LCD BACK LIGHT)
************************************************************
A-4751-431-A BD81A BOARD, COMPLETE
**********************
< CAPACITOR >
C10
C11
C14
C15
C16

1-165-989-11
1-165-989-11
1-164-360-11
1-164-360-11
1-115-156-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

10uF
10uF
0.1uF
0.1uF
1uF

10%
10%

C17
C18
C111
C112
C113

1-126-246-11
1-162-964-11
1-162-967-11
1-164-315-11
1-162-967-11

ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

220uF
0.001uF
0.0033uF
470PF
0.0033uF

20%
10%
10%
5%
10%

4V
50V
50V
50V
50V

C114
C115
C116
C122
C123

1-164-315-11
1-164-360-11
1-128-995-21
1-107-826-11
1-107-826-11

CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP

470PF
0.1uF
100uF
0.1uF
0.1uF

5%

50V
16V
10V
16V
16V

C124
C125
C131
C132
C133

1-162-959-11
1-164-360-11
1-162-927-11
1-117-863-11
1-162-970-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

330PF
0.1uF
100PF
0.47uF
0.01uF

5%
5%
10%
10%

50V
16V
50V
6.3V
25V

C134
C141
C142
C143
C151

1-164-360-11
1-107-826-11
1-162-965-11
1-164-360-11
1-128-995-21

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP

0.1uF
0.1uF
10%
0.0015uF 10%
0.1uF
100uF
20%

16V
16V
50V
16V
10V

C161
C162
C163
C171

1-164-360-11
1-164-360-11
1-164-360-11
1-162-919-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

0.1uF
0.1uF
0.1uF
22PF

16V
16V
16V
50V

66

20%
10%
10%

5%

6.3V
6.3V
16V
16V
10V

20%

20%

20%

16V
4V
16V
16V
4V
16V
16V
16V
16V
16V

20%
10%
10%
10%
10%

4V
16V
50V
25V
25V

HCD-CPX11
BD81A
Ref. No.

Part No.

Description

Remark

< CONNECTOR >

CN101
CN201

1-770-425-11 CONNECTOR, FFC/FPC 16P

1-818-350-11 CONNECTOR (FFC) 27P

Ref. No.

DRIVER

HP

Part No.

Description

R351
R352
R353
R354
R401

1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11

METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP

100
100
100
100
100

5%
5%
5%
5%
5%

Remark
1/10W
1/10W
1/10W
1/10W
1/10W

R402
R403
R404
R405
R406

1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11

METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP

100
100
100
100
100

5%
5%
5%
5%
5%

1/10W
1/10W
1/10W
1/10W
1/10W

R407
R408
R409
R410
R411

1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11

METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP

100
100
100
100
100

5%
5%
5%
5%
5%

1/10W
1/10W
1/10W
1/10W
1/10W

R412
R419

1-216-809-11 METAL CHIP

1-216-809-11 METAL CHIP

100
100

5%
5%

1/10W
1/10W

< FERRITE BEAD >

FB301

1-500-445-21 FERRITE, EMI (SMD) (2012)

< IC >

IC101
IC251
IC301
IC303

8-752-425-12
6-705-808-01
6-705-365-01
6-705-807-01

IC
IC
IC
IC

CXD3059AR
BA5947FM
TC94A34FG-002
BH15FB1WG

< TRANSISTOR >

Q10

6-550-363-01 TRANSISTOR

2SB1690KT146

< RESISTOR >

< SWITCH >
R10
R11
R12
R13
R111

1-216-791-11
1-216-864-11
1-216-845-11
1-218-446-11
1-216-821-11

METAL CHIP
SHORT CHIP
METAL CHIP
METAL CHIP
METAL CHIP

3.3
0
100K
1
1K

5%

1/10W

5%
5%
5%

1/10W
1/10W
1/10W

R112
R113
R114
R121
R131

1-216-835-11
1-216-821-11
1-216-835-11
1-216-835-11
1-216-857-11

METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP

15K
1K
15K
15K
1M

5%
5%
5%
5%
5%

1/10W
1/10W
1/10W
1/10W
1/10W

R132
R133
R141
R142
R143

1-216-833-11
1-216-848-11
1-216-829-11
1-216-821-11
1-216-827-11

METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP

10K
180K
4.7K
1K
3.3K

5%
5%
5%
5%
5%

1/10W
1/10W
1/10W
1/10W
1/10W

R151
R161
R162
R163
R165

1-216-864-11
1-216-809-11
1-216-841-11
1-216-809-11
1-216-864-11

SHORT CHIP
METAL CHIP
METAL CHIP
METAL CHIP
SHORT CHIP

0
100
47K
100
0

5%
5%
5%

1/10W
1/10W
1/10W

R171
R172
R173
R181
R182

1-216-817-11
1-216-857-11
1-216-295-91
1-216-809-11
1-216-809-11

METAL CHIP
METAL CHIP
SHORT CHIP
METAL CHIP
METAL CHIP

470
1M
0
100
100

R191
R201
R203
R204
R205

1-216-864-11
1-500-445-21
1-216-864-11
1-500-445-21
1-216-864-11

SHORT CHIP
0
FERRITE, EMI (SMD) (2012)
SHORT CHIP
0
FERRITE, EMI (SMD) (2012)
SHORT CHIP
0

R251
R252
R253
R301
R302

1-216-833-11
1-216-837-11
1-216-833-11
1-216-845-11
1-216-833-11

METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP

10K
22K
10K
100K
10K

5%
5%
5%
5%
5%

1/10W
1/10W
1/10W
1/10W
1/10W

R303
R305
R306
R307
R313

1-216-845-11
1-216-845-11
1-216-864-11
1-216-833-11
1-216-813-11

METAL CHIP
METAL CHIP
SHORT CHIP
METAL CHIP
METAL CHIP

100K
100K
0
10K
220

5%
5%

1/10W
1/10W

5%
5%

1/10W
1/10W

S101

1-771-853-11 SWITCH,DETECTION (LIMIT)

< VIBRATOR >

X171
1-767-408-21 VIBRATOR, CRYSTAL (16.9MHz)
************************************************************
1-688-337-11 DRIVER BOARD
************
< CAPACITOR >
C705
C711

5%
5%

1/10W
1/10W

20%
20%

16V
50V

1-785-333-11 PIN, CONNECTOR (LIGHT ANGLE) 7P

< DIODE >

D701
1/10W
1/10W

0.01uF
10uF

< CONNECTOR >

CN701

5%
5%

1-162-306-11 CERAMIC
1-126-964-11 ELECT

8-719-921-40 DIODE MTZJ-4.7C

< IC >

IC701

8-759-598-69 IC BA6956AN
< RESISTOR >

R701
R702

1-249-415-11 CARBON
1-247-807-31 CARBON

680
100

5%
5%

1/4W
1/4W

< SWITCH >

S701
1-762-951-13 SWITCH, PUSH (OUT)
S702
1-762-951-13 SWITCH, PUSH (CHUCK)
S703
1-762-951-13 SWITCH, PUSH (TRIGGER)
************************************************************
HP BOARD
*********
< CAPACITOR >
C891
C892

1-164-156-11 CERAMIC CHIP

1-164-156-11 CERAMIC CHIP

0.1uF
0.1uF

25V
25V

67

HCD-CPX11
HP
Ref. No.
C894

LCD
Part No.

MAIN
Description

1-164-156-11 CERAMIC CHIP

Remark
0.1uF

< FERRITE BEAD >

FB891
FB893
FB894

1-216-864-11 SHORT CHIP

1-216-864-11 SHORT CHIP
1-216-864-11 SHORT CHIP

0
0
0

< JACK >

J801
1-815-603-11 JACK (PHONES)
************************************************************
1-861-335-11 LCD BOARD
**********
< CAPACITOR >
C854
C856
C857
C858
C859

1-164-156-11
1-162-927-11
1-162-927-11
1-162-927-11
1-162-927-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

0.1uF
100PF
100PF
100PF
100PF

5%
5%
5%
5%

25V
50V
50V
50V
50V

C860

1-162-927-11 CERAMIC CHIP

100PF

5%

50V

< CONNECTOR >

CN805
CN806

Ref. No.

Part No.

25V

1-784-731-11 CONNECTOR, FFC 9P

1-770-010-21 CONNECTOR, BOARD TO BOARD 4P

Description

Remark

< CAPACITOR >

C213
C218
C219
C221
C222

1-162-923-11
1-162-927-11
1-162-927-11
1-162-927-11
1-162-927-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

47PF
100PF
100PF
100PF
100PF

5%
5%
5%
5%
5%

50V
50V
50V
50V
50V

C223
C224
C228
C229
C230

1-162-927-11
1-162-927-11
1-104-658-91
1-107-826-11
1-104-658-91

CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
ELECT

100PF
100PF
100uF
0.1uF
100uF

5%
5%
20%
10%
20%

50V
50V
10V
16V
10V

C231
C232
C233
C234
C235

1-107-826-11
1-104-658-91
1-107-826-11
1-104-658-91
1-162-927-11

CERAMIC CHIP
ELECT
CERAMIC CHIP
ELECT
CERAMIC CHIP

0.1uF
100uF
0.1uF
100uF
100PF

10%
20%
10%
20%
5%

16V
10V
16V
10V
50V

C236
C237
C238
C239
C240

1-162-927-11
1-107-826-11
1-107-826-11
1-107-826-11
1-107-826-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

100PF
0.1uF
0.1uF
0.1uF
0.1uF

5%
10%
10%
10%
10%

50V
16V
16V
16V
16V

C241
C251
C252
C267
C268

1-107-826-11
1-126-961-11
1-126-961-11
1-164-156-11
1-104-658-91

CERAMIC CHIP
ELECT
ELECT
CERAMIC CHIP
ELECT

0.1uF
2.2uF
2.2uF
0.1uF
100uF

10%
20%
20%

16V
50V
50V
25V
10V

C301
C310
C311
C312
C316

1-126-916-11
1-162-917-11
1-162-919-11
1-164-156-11
1-164-156-11

ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

1000uF
15PF
22PF
0.1uF
0.1uF

20%
5%
5%

6.3V
50V
50V
25V
25V

C331
C332
C351
C352
C353

1-126-964-11
1-126-964-11
1-126-937-11
1-126-956-91
1-126-925-91

ELECT
ELECT
ELECT
ELECT
ELECT

10uF
10uF
4700uF
0.1uF
470uF

20%
20%
20%
20%
20%

50V
50V
16V
50V
10V

C354
C355
C356
C357
C358

1-126-956-91
1-126-925-91
1-126-956-91
1-126-925-91
1-126-956-91

ELECT
ELECT
ELECT
ELECT
ELECT

0.1uF
470uF
0.1uF
470uF
0.1uF

20%
20%
20%
20%
20%

50V
10V
50V
10V
50V

C359
C360
C364
C401
C450

1-104-658-91
1-126-925-91
1-164-156-11
1-126-964-11
1-104-658-91

ELECT
ELECT
CERAMIC CHIP
ELECT
ELECT

100uF
470uF
0.1uF
10uF
100uF

20%
20%
20%
20%

10V
10V
25V
50V
10V

C451
C502
C503

1-164-156-11 CERAMIC CHIP

1-130-495-00 MYLAR
1-130-495-00 MYLAR

0.1uF
0.1uF
0.1uF

5%
5%

25V
50V
50V

20%

< SHORT >

JR801
JR802
JR803
JR804
JR805

1-216-296-11
1-216-296-11
1-216-296-11
1-216-296-11
1-216-296-11

SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP

0
0
0
0
0

JR806

1-216-296-11 SHORT CHIP

< LIQUID CRYSTAL DISPLAY >

LCD800 1-805-545-11 DISPLAY PANEL, LIQUID CRYSTAL
< RESISTOR >
R841
R842
R843
R844
R851

1-216-817-11
1-216-817-11
1-216-817-11
1-216-817-11
1-216-847-11

METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP

470
470
470
470
150K

5%
5%
5%
5%
5%

1/10W
1/10W
1/10W
1/10W
1/10W

R853
R854
R856
R857
R858

1-216-821-11
1-216-833-11
1-216-809-11
1-216-809-11
1-216-809-11

METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP

1K
10K
100
100
100

5%
5%
5%
5%
5%

1/10W
1/10W
1/10W
1/10W
1/10W

R859
1-216-809-11 METAL CHIP
100
5%
1/10W
R860
1-216-809-11 METAL CHIP
100
5%
1/10W
************************************************************
A-4750-353-A MAIN BOARD, COMPLETE (AEP, UK)
A-4750-940-A MAIN BOARD, COMPLETE (KR, AUS)
*********************
7-685-645-79 SCREW +BVTP 3X6 TYPE2 TT (B)

68

< CONNECTOR >

CN201
CN202
CN301
CN302
CN303

1-779-295-11
1-785-319-11
1-564-505-11
1-785-315-11
1-784-780-11

CONNECTOR, FFC (LIF (NON-ZIF)) 27P

PIN, CONNECTOR (STRAIGHT) 7P
PLUG, CONNECTOR 2P
PIN, CONNECTOR (STRAIGHT) 3P
CONNECTOR, FFC 19P

HCD-CPX11
MAIN
Ref. No.

Part No.

Description

CN304
CN306
CN307
CN307
CN308

1-568-828-11
1-784-780-11
1-568-830-11
1-784-776-11
1-784-780-11

CONNECTOR, FFC 9P
CONNECTOR, FFC 19P
CONNECTOR, FFC 11P (KR, AUS)
CONNECTOR, FFC 15P (AEP, UK)
CONNECTOR, FFC 19P

Remark

CN309

1-568-838-11 CONNECTOR, FFC 21P

< DIODE >

D201
D202
D203
D204
D205

8-719-988-61
6-500-522-31
6-500-522-31
6-500-522-31
6-500-522-31

DIODE
DIODE
DIODE
DIODE
DIODE

1SS355TE-17
10EDB40-TB5
10EDB40-TB5
10EDB40-TB5
10EDB40-TB5

D301
D302
D303
D304
D350

8-719-988-61
8-719-988-61
8-719-988-61
8-719-988-61
6-500-522-31

DIODE
DIODE
DIODE
DIODE
DIODE

1SS355TE-17
1SS355TE-17
1SS355TE-17
1SS355TE-17
10EDB40-TB5

D351
D352
D374
D375
D401

6-500-522-31
6-500-522-31
8-719-988-61
8-719-988-61
8-719-988-61

DIODE
DIODE
DIODE
DIODE
DIODE

10EDB40-TB5
10EDB40-TB5
1SS355TE-17
1SS355TE-17
1SS355TE-17

D402
D403
D404
D442
D443

8-719-988-61
8-719-988-61
8-719-988-61
1-216-295-91
1-216-295-91

DIODE 1SS355TE-17
DIODE 1SS355TE-17
DIODE 1SS355TE-17
SHORT CHIP
0
SHORT CHIP
0

Ref. No.

Part No.

Description

Q202
Q331
Q332
Q333

8-729-027-43
8-729-027-23
8-729-027-43
8-729-027-30

TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR

DTC114EKA-T146
DTA114EKA-T146
DTC114EKA-T146
DTA123YKA-T146

Remark

Q334
Q340
Q341
Q342
Q343

8-729-027-43
8-729-027-43
8-729-027-23
8-729-107-43
8-729-107-43

TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR

DTC114EKA-T146
DTC114EKA-T146
DTA114EKA-T146
2SC3624-L18
2SC3624-L18

Q401

8-729-119-78 TRANSISTOR

2SC2785-HFE

< RESISTOR >

R251
R252
R253
R254
R301

1-216-821-11
1-216-821-11
1-216-845-11
1-216-845-11
1-216-809-11

METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP

1K
1K
100K
100K
100

5%
5%
5%
5%
5%

1/10W
1/10W
1/10W
1/10W
1/10W

R302
R303
R304
R305
R306

1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11

METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP

100
100
100
100
100

5%
5%
5%
5%
5%

1/10W
1/10W
1/10W
1/10W
1/10W

R307
R309
R311
R313
R317

1-216-809-11
1-216-833-11
1-216-851-11
1-216-864-11
1-216-833-11

METAL CHIP
METAL CHIP
METAL CHIP
SHORT CHIP
METAL CHIP

100
10K
330K
0
10K

5%
5%
5%

1/10W
1/10W
1/10W

5%

1/10W

R318

1-216-809-11 METAL CHIP

100

5%

R319
R320
R321
R322

1-216-809-11
1-216-829-11
1-216-809-11
1-216-809-11

METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP

100
4.7K
100
100

5%
5%
5%
5%

1/10W
(AEP, UK)
1/10W
1/10W
1/10W
1/10W

R323
R326
R327
R328
R332

1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11

METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP

100
100
100
100
100

5%
5%
5%
5%
5%

1/10W
1/10W
1/10W
1/10W
1/10W

R333
R334
R335
R336
R337

1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11

METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP

100
100
100
100
100

5%
5%
5%
5%
5%

1/10W
1/10W
1/10W
1/10W
1/10W

R339
R340
R341
R342
R343

1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11

METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP

100
100
100
100
100

5%
5%
5%
5%
5%

1/10W
1/10W
1/10W
1/10W
1/10W

R344
R345
R346
R347
R348

1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11

METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP

100
100
100
100
100

5%
5%
5%
5%
5%

1/10W
1/10W
1/10W
1/10W
1/10W

R349
R350
R351
R352
R353

1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11

METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP

100
100
100
100
100

5%
5%
5%
5%
5%

1/10W
1/10W
1/10W
1/10W
1/10W

< EARTH TERMINAL >

* EP301
* EP302

1-537-738-21 TERMINAL, EARTH

1-537-738-21 TERMINAL, EARTH
< FERRITE BEAD >

FB201
FB203
FB205
FB207
FB214

1-414-772-11
1-414-772-11
1-414-772-11
1-414-772-11
1-414-772-11

FERRITE. EMI (SMD) (2012)

FERRITE. EMI (SMD) (2012)
FERRITE. EMI (SMD) (2012)
FERRITE. EMI (SMD) (2012)
FERRITE. EMI (SMD) (2012)

FB216
FB225
FB227
FB301
FB302

1-414-772-11
1-414-772-11
1-414-772-11
1-216-864-11
1-216-864-11

FERRITE. EMI (SMD) (2012)

FERRITE. EMI (SMD) (2012)
FERRITE. EMI (SMD) (2012)
SHORT CHIP
0
SHORT CHIP
0

FB303

1-216-864-11 SHORT CHIP

< IC >
IC201
IC202
IC203
IC204
IC300

8-759-701-59
8-759-071-48
6-703-546-01
8-759-231-53
6-804-485-01

IC
IC
IC
IC
IC

NJM78M09FA
TA7807S
TA7804LS
TA7805S
M3062CMEN-A14FPU0

IC401
IC450

8-759-532-64 IC M62703SL-TP
8-749-019-25 IC TOTX141 (CD DIGITAL OUT (OPTICAL))
< TRANSISTOR >

Q201

8-729-049-79 TRANSISTOR

RT1P137S-TP

69

HCD-CPX11
MAIN
Ref. No.

PANEL
Part No.

Description

Remark

Ref. No.

Part No.

Description

Remark

R483
R484
R485

1-216-833-11 METAL CHIP

1-216-833-11 METAL CHIP
1-216-833-11 METAL CHIP

10K
10K
10K

5%
5%
5%

1/10W
1/10W
1/10W

R486
R487
R488
R493
R494

1-216-833-11
1-216-833-11
1-216-833-11
1-216-864-11
1-216-833-11

10K
5%
10K
5%
10K
5%
0 (AEP, UK)
10K
5%

1/10W
1/10W
1/10W

R495
R497
R500

1-216-833-11 METAL CHIP

1-216-833-11 METAL CHIP
1-216-833-11 METAL CHIP

10K
10K
10K

1/10W
1/10W
1/10W

R354

1-216-809-11 METAL CHIP

100

5%

R355
R357
R361
R365

1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11

METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP

100
100
100
100

5%
5%
5%
5%

1/10W
(AEP, UK)
1/10W
1/10W
1/10W
1/10W

R366
R367
R368
R369
R370

1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11

METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP

100
100
100
100
100

5%
5%
5%
5%
5%

1/10W
1/10W
1/10W
1/10W
1/10W

R371
R372
R373
R375
R376

1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11

METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP

100
100
100
100
100

5%
5%
5%
5%
5%

1/10W
1/10W
1/10W
1/10W
1/10W

R377
R378
R379
R380
R381

1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11

METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP

100
100
100
100
100

5%
5%
5%
5%
5%

1/10W
1/10W
1/10W
1/10W
1/10W

R382
R383
R384
R385
R386

1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11

METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP

100
100
100
100
100

5%
5%
5%
5%
5%

1/10W
1/10W
1/10W
1/10W
1/10W

C803
C804
C805
C806
C807

1-164-156-11
1-164-156-11
1-164-156-11
1-164-156-11
1-164-156-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

0.1uF
0.1uF
0.1uF
0.1uF
0.1uF

R387
R388
R389
R390
R391

1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11

METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP

100
100
100
100
100

5%
5%
5%
5%
5%

1/10W
1/10W
1/10W
1/10W
1/10W

C808
C817

1-164-156-11 CERAMIC CHIP

1-126-947-11 ELECT

0.1uF
47uF

R392
R393
R394
R395
R397

1-216-864-11
1-216-864-11
1-216-797-11
1-216-797-11
1-216-797-11

SHORT CHIP
SHORT CHIP
METAL CHIP
METAL CHIP
METAL CHIP

0
0 (KR, AUS)
10
5%
10
5%
10
5%

1/10W
1/10W
1/10W

R400
R401
R402
R403
R404

1-216-809-11
1-216-813-11
1-216-833-11
1-216-841-11
1-216-841-11

METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP

100
220
10K
47K
47K

5%
5%
5%
5%
5%

1/10W
1/10W
1/10W
1/10W
1/10W

R405
R406
R418
R420
R426

1-216-833-11
1-216-829-11
1-216-864-11
1-216-833-11
1-216-833-11

METAL CHIP
METAL CHIP
SHORT CHIP
METAL CHIP
METAL CHIP

10K
5%
4.7K
5%
0 (KR, AUS)
10K
5%
10K
5%

1/10W
1/10W

R427
R428
R429
R430
R440

1-216-833-11
1-216-833-11
1-216-833-11
1-216-833-11
1-216-833-11

METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP

10K
10K
10K
10K
10K

5%
5%
5%
5%
5%

1/10W
1/10W
1/10W
1/10W
1/10W

R442
R443
R450
R451
R452

1-216-833-11
1-216-833-11
1-216-809-11
1-216-833-11
1-216-833-11

METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP

10K
10K
100
10K
10K

5%
5%
5%
5%
5%

1/10W
1/10W
1/10W
1/10W
1/10W

R455
R474

1-216-864-11 SHORT CHIP

1-216-857-11 METAL CHIP

0 (KR, AUS)
1M
5%

1/10W

X401
1-795-482-11 VIBRATOR, CERAMIC (16MHz)
X402
1-760-252-12 VIBRATOR, CRYSTAL (32.768kHz)
************************************************************
A-4750-358-A PANEL BOARD, COMPLETE
**********************
< CAPACITOR >
25V
25V
25V
25V
25V

20%

25V
35V

< CONNECTOR >

1-784-780-11 CONNECTOR, FFC 19P
1-785-330-11 PIN, CONNECTOR (LIGHT ANGLE) 4P
< DIODE >
D812
D813
D816
D818

8-719-046-36
8-719-812-44
8-719-046-36
8-719-046-36

DIODE
DIODE
DIODE
DIODE

SEL5921A-TP15 (DSGX)
TLO124 (STAND BY)
SEL5921A-TP15 (TUNER/BAND)
SEL5921A-TP15 (TAPE nN)

< IC >
IC802

70

5%
5%
5%

1/10W

< VIBRATOR >

CN801
CN802

1/10W
1/10W

METAL CHIP
METAL CHIP
METAL CHIP
SHORT CHIP
METAL CHIP

6-600-349-31 IC NJL24H400A ( )
< TRANSISTOR >

Q812
Q813
Q816
Q818

8-729-027-43
8-729-027-43
8-729-027-43
8-729-027-43

TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR

DTC114EKA-T146
DTC114EKA-T146
DTC114EKA-T146
DTC114EKA-T146

< RESISTOR >

R801
R802
R803
R804
R805

1-216-821-11
1-216-825-11
1-216-825-11
1-216-829-11
1-216-821-11

METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP

1K
2.2K
2.2K
4.7K
1K

5%
5%
5%
5%
5%

1/10W
1/10W
1/10W
1/10W
1/10W

R806
R807
R808

1-216-825-11 METAL CHIP

1-216-821-11 METAL CHIP
1-216-825-11 METAL CHIP

2.2K
1K
2.2K

5%
5%
5%

1/10W
1/10W
1/10W

HCD-CPX11
PANEL
Ref. No.

Part No.

Description

Remark

R809
R810

1-216-825-11 METAL CHIP

1-216-829-11 METAL CHIP

2.2K
4.7K

5%
5%

1/10W
1/10W

R811
R812
R813
R814
R815

1-216-833-11
1-216-837-11
1-216-809-11
1-216-809-11
1-216-809-11

METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP

10K
22K
100
100
100

5%
5%
5%
5%
5%

1/10W
1/10W
1/10W
1/10W
1/10W

R816
R821
R822
R823
R825

1-216-809-11
1-216-817-11
1-216-817-11
1-216-817-11
1-216-805-11

METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP

100
470
470
470
47

5%
5%
5%
5%
5%

1/10W
1/10W
1/10W
1/10W
1/10W

R826
R828

1-216-817-11 METAL CHIP

1-216-817-11 METAL CHIP

470
470

5%
5%

1/10W
1/10W

< VARIABLE RESISTOR >

RV803
RV805
RV807

1-476-730-11 ENCODER, ROTARY (VOLUME)

1-418-859-21 ENCODER, ROTARY (BASS)
1-418-859-21 ENCODER, ROTARY (TREBLE)
< SWITCH >

S801
S802
S803
S804
S805

1-762-875-21 SWITCH, KEYBOARD (?/1)

1-762-875-21 SWITCH, KEYBOARD (DSGX)
1-762-875-21 SWITCH, KEYBOARD
(PLAY MODE/DIRECTION/TUNING MODE)
1-762-875-21 SWITCH, KEYBOARD (REPEAT/FM MODE)
1-762-875-21 SWITCH, KEYBOARD (CD SYNCHRO)

S806
S807
S808
S809
S810

1-762-875-21
1-771-574-21
1-771-574-21
1-762-875-21
1-762-875-21

Ref. No.

PRE AMP

Part No.

Description

C129
C131
C132
C133
C141

1-162-927-11
1-104-658-91
1-107-826-11
1-104-658-91
1-107-826-11

CERAMIC CHIP
ELECT
CERAMIC CHIP
ELECT
CERAMIC CHIP

100PF
100uF
0.1uF
100uF
0.1uF

5%
20%
10%
20%
10%

50V
10V
16V
10V
16V

Remark

C151
C152
C153
C154
C155

1-162-957-11
1-126-960-11
1-126-960-11
1-126-960-11
1-126-960-11

CERAMIC CHIP
ELECT
ELECT
ELECT
ELECT

220PF
1uF
1uF
1uF
1uF

5%
20%
20%
20%
20%

50V
50V
50V
50V
50V

C156
C157
C158
C159
C160

1-126-960-11
1-126-960-11
1-130-476-00
1-130-496-00
1-130-496-00

ELECT
ELECT
MYLAR
MYLAR
MYLAR

1uF
1uF
0.0027uF
0.12uF
0.12uF

20%
20%
5%
5%
5%

50V
50V
50V
50V
50V

C161
C171
C172
C173
C174

1-126-964-11
1-126-964-11
1-162-915-11
1-126-964-11
1-126-923-91

ELECT
ELECT
CERAMIC CHIP
ELECT
ELECT

10uF
10uF
10PF
10uF
220uF

20%
20%
0.5PF
20%
20%

50V
50V
50V
50V
10V

C179
C180
C181
C182
C183

1-162-927-11
1-126-923-91
1-104-658-91
1-126-960-11
1-104-658-91

CERAMIC CHIP
ELECT
ELECT
ELECT
ELECT

100PF
220uF
100uF
1uF
100uF

5%
20%
20%
20%
20%

50V
10V
10V
50V
10V

C185

1-126-960-11 ELECT

1uF

20%

50V

< CONNECTOR >

SWITCH, KEYBOARD (FUNCTON)
SWITCH, TACTILE (TUNING + LM)
SWITCH, TACTILE (- TUNING lm)
SWITCH, KEYBOARD (DISPLAY)
SWITCH, KEYBOARD (TUNER/BAND)

S811
1-762-875-21 SWITCH, KEYBOARD ((CD) Z)
S812
1-762-875-21 SWITCH, KEYBOARD (z REC)
S813
1-762-875-21 SWITCH, KEYBOARD ((TAPE) X)
S814
1-762-875-21 SWITCH, KEYBOARD ((TAPE) x)
S815
1-762-875-21 SWITCH, KEYBOARD (TAPE nN)
************************************************************

CN101
CN102

1-784-780-11 CONNECTOR, FFC 19P

1-785-330-11 PIN, CONNECTOR (LIGHT ANGLE) 4P
< IC >

IC101
IC102

8-759-669-03 IC LC75342
8-759-656-83 IC NJM4580MD-(TE2)
< JACK >

J101

1-817-877-11 JACK, PIN 2P (MD (VIDEO))

< TRANSISTOR >

A-4750-356-A PRE AMP BOARD, COMPLETE

************************
< CAPACITOR >
C101
C102
C103
C104
C105

1-162-957-11
1-126-960-11
1-126-960-11
1-126-960-11
1-126-960-11

CERAMIC CHIP
ELECT
ELECT
ELECT
ELECT

220PF
1uF
1uF
1uF
1uF

5%
20%
20%
20%
20%

50V
50V
50V
50V
50V

C106
C107
C108
C109
C110

1-126-960-11
1-126-960-11
1-130-476-00
1-130-496-00
1-130-496-00

ELECT
ELECT
MYLAR
MYLAR
MYLAR

1uF
1uF
0.0027uF
0.12uF
0.12uF

20%
20%
5%
5%
5%

50V
50V
50V
50V
50V

C111
C121
C122
C123
C124

1-126-964-11
1-126-964-11
1-162-915-11
1-126-964-11
1-126-923-91

ELECT
ELECT
CERAMIC CHIP
ELECT
ELECT

10uF
10uF
10PF
10uF
220uF

20%
20%
0.5PF
20%
20%

50V
50V
50V
50V
10V

Q101
Q121
Q122
Q151
Q180

8-729-107-43
8-729-027-23
8-729-027-43
8-729-107-43
8-729-107-43

TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR

2SC3624-L18
DTA114EKA-T146
DTC114EKA-T146
2SC3624-L18
2SC3624-L18

Q181
Q182
Q183
Q184
Q185

8-729-107-43
8-729-107-43
8-729-107-43
8-729-027-23
8-729-027-43

TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR

2SC3624-L18
2SC3624-L18
2SC3624-L18
DTA114EKA-T146
DTC114EKA-T146

< RESISTOR >

R101
R102
R103
R104
R105

1-216-833-11
1-216-832-11
1-216-828-11
1-216-821-11
1-216-833-11

METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP

10K
8.2K
3.9K
1K
10K

5%
5%
5%
5%
5%

1/10W
1/10W
1/10W
1/10W
1/10W

71

HCD-CPX11
PRE AMP
Ref. No.

S-MASTER AMP

Part No.

Description

R106
R121
R122
R123
R124

1-216-833-11
1-216-821-11
1-216-845-11
1-216-829-11
1-216-837-11

METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP

10K
1K
100K
4.7K
22K

5%
5%
5%
5%
5%

1/10W
1/10W
1/10W
1/10W
1/10W

Remark

R125
R126
R131
R132
R133

1-216-805-11
1-216-845-11
1-216-809-11
1-216-809-11
1-216-809-11

METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP

47
100K
100
100
100

5%
5%
5%
5%
5%

1/10W
1/10W
1/10W
1/10W
1/10W

R151
R152
R153
R154
R155

1-216-833-11
1-216-832-11
1-216-828-11
1-216-821-11
1-216-833-11

METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP

10K
8.2K
3.9K
1K
10K

5%
5%
5%
5%
5%

1/10W
1/10W
1/10W
1/10W
1/10W

R156
R171
R172
R173
R174

1-216-833-11
1-216-821-11
1-216-845-11
1-216-829-11
1-216-837-11

METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP

10K
1K
100K
4.7K
22K

5%
5%
5%
5%
5%

1/10W
1/10W
1/10W
1/10W
1/10W

R175
R176
R180
R181
R182

1-216-805-11
1-216-845-11
1-216-829-11
1-216-825-11
1-216-826-11

METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP

47
100K
4.7K
2.2K
2.7K

5%
5%
5%
5%
5%

1/10W
1/10W
1/10W
1/10W
1/10W

R183
1-216-833-11 METAL CHIP
10K
5%
1/10W
R184
1-216-821-11 METAL CHIP
1K
5%
1/10W
R185
1-216-821-11 METAL CHIP
1K
5%
1/10W
************************************************************
A-4750-366-A S-MASTER AMP BOARD, COMPLETE
*****************************

Ref. No.

Part No.

Description

Remark

C623
C625

1-162-927-11 CERAMIC CHIP

1-126-963-11 ELECT

100PF
4.7uF

5%
20%

50V
50V

C628
C629
C630
C631
C632

1-126-963-11
1-107-726-91
1-107-826-11
1-126-963-11
1-104-658-91

ELECT
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT

4.7uF
0.01uF
0.1uF
4.7uF
100uF

20%
10%
10%
20%
20%

50V
16V
16V
50V
10V

C633
C634
C635
C636
C637

1-162-970-11
1-162-970-11
1-162-970-11
1-162-970-11
1-162-970-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

0.01uF
0.01uF
0.01uF
0.01uF
0.01uF

10%
10%
10%
10%
10%

25V
25V
25V
25V
25V

C638
C639
C640
C648
C649

1-162-970-11
1-162-970-11
1-104-658-91
1-107-826-11
1-104-658-91

CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
ELECT

0.01uF
0.01uF
100uF
0.1uF
100uF

10%
10%
20%
10%
20%

25V
25V
10V
16V
10V

C650
C651
C652
C653
C654

1-107-826-11
1-137-372-11
1-104-658-91
1-164-505-11
1-162-974-11

CERAMIC CHIP
MYLAR
ELECT
CERAMIC CHIP
CERAMIC CHIP

0.1uF
0.022uF
100uF
2.2uF
0.01uF

10%
5%
20%

16V
50V
10V
16V
50V

C655
C656
C659
C660
C661

1-137-807-31
1-131-704-11
1-162-974-11
1-162-974-11
1-137-372-11

ELECT
FILM
CERAMIC CHIP
CERAMIC CHIP
MYLAR

100uF
1uF
0.01uF
0.01uF
0.022uF

20%
5%

50V
50V
50V
50V
50V

C663
C666
C668
C669
C670

1-164-505-11
1-131-704-11
1-107-826-11
1-162-974-11
1-162-974-11

CERAMIC CHIP
FILM
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

2.2uF
1uF
0.1uF
0.01uF
0.01uF

C671
C672
C673
C674
C675

1-137-372-11
1-104-658-91
1-164-505-11
1-216-864-11
1-137-807-31

MYLAR
ELECT
CERAMIC CHIP
SHORT CHIP
ELECT

0.022uF
100uF
2.2uF
0
100uF

5%
20%

50V
10V
16V

20%

50V

C676
C678
C679
C680
C681

1-131-704-11
1-107-826-11
1-162-974-11
1-162-974-11
1-137-372-11

FILM
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
MYLAR

1uF
0.1uF
0.01uF
0.01uF
0.022uF

5%
10%

50V
16V
50V
50V
50V

C682
C683
C686
C689
C690

1-104-658-91
1-164-505-11
1-131-704-11
1-162-974-11
1-162-974-11

ELECT
CERAMIC CHIP
FILM
CERAMIC CHIP
CERAMIC CHIP

100uF
2.2uF
1uF
0.01uF
0.01uF

20%

C692
C693
C694
C697
C698

1-164-505-11
1-164-505-11
1-164-346-11
1-216-864-11
1-162-974-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
SHORT CHIP
CERAMIC CHIP

2.2uF
2.2uF
1uF
0
0.01uF

16V
16V
16V

C699

1-162-974-11 CERAMIC CHIP

0.01uF

50V

5%

5%
10%

16V
50V
16V
50V
50V

7-685-645-79 SCREW +BVTP 3X6 TYPE2 TT (B)

< CAPACITOR >
C600
C601
C602
C603
C604

1-128-549-11
1-104-658-91
1-126-964-11
1-164-156-11
1-164-156-11

ELECT
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP

3300uF
100uF
10uF
0.1uF
0.1uF

C605
C606
C607
C608
C609

1-164-156-11
1-164-156-11
1-164-156-11
1-126-964-11
1-162-971-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP

0.1uF
0.1uF
0.1uF
10uF
0.001uF

C610
C611
C612
C613
C614

1-164-156-11
1-126-960-11
1-107-826-11
1-216-864-11
1-162-915-11

CERAMIC CHIP
ELECT
CERAMIC CHIP
SHORT CHIP
CERAMIC CHIP

0.1uF
1uF
0.1uF
0
10PF

C615
C616
C617
C618
C619

1-162-915-11
1-104-662-91
1-162-970-11
1-162-908-11
1-162-908-11

CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

C620
C621
C622

1-162-964-11 CERAMIC CHIP

1-126-960-11 ELECT
1-164-156-11 CERAMIC CHIP

20%
20%
20%

35V
10V
50V
25V
25V

20%
10%

25V
25V
25V
50V
50V

20%
10%

25V
50V
16V

0.5PF

50V

10PF
22uF
0.01uF
3PF
3PF

0.5PF
20%
10%
0.25PF
0.25PF

50V
25V
25V
50V
50V

0.001uF
1uF
0.1uF

10%
20%

50V
50V
25V

< CONNECTOR >

72

* CN600
CN601

1-564-508-11 PLUG, CONNECTOR 5P

1-568-838-11 CONNECTOR, FFC 21P

5%

5%

10V
16V
50V
50V
50V

50V

HCD-CPX11
S-MASTER AMP
Ref. No.

Part No.

Description

Remark

D611
D621
D650
D651
D652

8-719-988-61
8-719-988-61
6-500-131-01
6-500-248-01
6-500-060-01

DIODE
DIODE
DIODE
DIODE
DIODE

1SS355TE-17
1SS355TE-17
LI116
SFPL-62V
P6SMB36AT3

D660
D661
D662
D670
D671

6-500-131-01
6-500-248-01
6-500-060-01
6-500-131-01
6-500-248-01

DIODE
DIODE
DIODE
DIODE
DIODE

LI116
SFPL-62V
P6SMB36AT3
LI116
SFPL-62V

D672
D680
D681
D682

6-500-060-01
6-500-131-01
6-500-248-01
6-500-060-01

DIODE
DIODE
DIODE
DIODE

P6SMB36AT3
LI116
SFPL-62V
P6SMB36AT3

< EARTH TERMINAL >

EP601
EP602
EP603

1-537-771-21 TERMINAL BOARD, GROUND

1-537-771-21 TERMINAL BOARD, GROUND
1-537-771-21 TERMINAL BOARD, GROUND
< FERRITE BEAD >

FB601
FB604
FB605
FB606
FB607

1-216-864-11
1-216-864-11
1-469-324-21
1-216-864-11
1-216-864-11

SHORT CHIP
0
SHORT CHIP
0
FERRITE, EMI (SMD) (2012)
SHORT CHIP
0
SHORT CHIP
0

FB610
FB620
FB640
FB641
FB642

1-469-324-21
1-469-324-21
1-216-864-11
1-216-864-11
1-216-864-11

FERRITE, EMI (SMD) (2012)

FERRITE, EMI (SMD) (2012)
SHORT CHIP
0
SHORT CHIP
0
SHORT CHIP
0

FB650
FB652
FB653
FB660
FB662

1-469-324-21
1-414-551-11
1-414-551-11
1-216-296-11
1-414-551-11

FERRITE, EMI (SMD) (2012)

FERRITE, EMI (SMD) (2012)
FERRITE, EMI (SMD) (2012)
SHORT CHIP
0
FERRITE, EMI (SMD) (2012)

FB663
FB670
FB680

1-414-551-11 FERRITE, EMI (SMD) (2012)

1-216-296-11 SHORT CHIP
0
1-469-324-21 FERRITE, EMI (SMD) (2012)
< IC >

IC600
IC603
IC604
IC610
IC618

6-703-287-01
6-701-834-01
8-759-387-77
6-701-189-01
6-700-263-01

IC
IC
IC
IC
IC

IC650
IC680

6-703-288-01 IC CXD9750L
6-703-288-01 IC CXD9750L

Ref. No.
L670

< DIODE >

CXD9743N
PCM1802DBR
TC7WU04F (TE12R)
MC74VHC1GU04DFT1
NJM2870F18 (TE2)

Part No.

Description

1-424-777-11 INDUCTOR

SP
Remark

10uH

< TRANSISTOR >

Q691
Q692
Q693
Q694
Q696

8-729-602-36
8-729-602-36
8-729-602-36
8-729-602-36
8-729-120-28

TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR

2SA1602-F
2SA1602-F
2SA1602-F
2SA1602-F
2SC1623-L5L6

< RESISTOR >

R601
R602
R603
R604
R605

1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
1-216-821-11

METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP

100
100
100
100
1K

5%
5%
5%
5%
5%

1/10W
1/10W
1/10W
1/10W
1/10W

R606
R607
R608
R609
R610

1-216-809-11
1-216-809-11
1-216-864-11
1-216-809-11
1-216-809-11

METAL CHIP
METAL CHIP
SHORT CHIP
METAL CHIP
METAL CHIP

100
100
0
100
100

5%
5%

1/10W
1/10W

5%
5%

1/10W
1/10W

R612
R613
R614
R615
R618

1-216-809-11
1-216-809-11
1-216-857-11
1-216-817-11
1-216-864-11

METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
SHORT CHIP

100
100
1M
470
0

5%
5%
5%
5%

1/10W
1/10W
1/10W
1/10W

R619
R620
R623
R640
R641

1-216-857-11
1-218-484-11
1-216-845-11
1-216-809-11
1-216-809-11

METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP

1M
750
100K
100
100

5%
5%
5%
5%
5%

1/10W
1/10W
1/10W
1/10W
1/10W

R642
R651
R652
R653
R661

1-216-809-11
1-216-296-11
1-216-809-11
1-216-809-11
1-216-296-11

METAL CHIP
SHORT CHIP
METAL CHIP
METAL CHIP
SHORT CHIP

100
0
100
100
0

5%

1/10W

5%
5%

1/10W
1/10W

R662
R663
R671
R681
R691

1-216-809-11
1-216-809-11
1-216-296-11
1-216-296-11
1-216-845-11

METAL CHIP
METAL CHIP
SHORT CHIP
SHORT CHIP
METAL CHIP

100
100
0
0
100K

5%
5%

1/10W
1/10W

5%

1/10W

R692
R693
R694
R695
R696

1-216-845-11
1-216-845-11
1-216-845-11
1-216-845-11
1-216-845-11

METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP

100K
100K
100K
100K
100K

5%
5%
5%
5%
5%

1/10W
1/10W
1/10W
1/10W
1/10W

R697

1-216-845-11 METAL CHIP

100K

5%

1/10W

< VIBRATOR >

X601
1-795-843-11 VIBRATOR, CRYSTAL (12.288MHz)
X602
1-795-660-21 QUARTZ CRYSTAL UNIT (49.152MHz)
************************************************************

< COIL >

L601
L602
L603
L604
L621

1-469-525-91
1-469-525-91
1-469-525-91
1-412-939-11
1-469-525-91

INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR

10uH
10uH
10uH
1uH
10uH

L650

1-424-777-11 INDUCTOR

10uH

SP BOARD
*********
< CAPACITOR >
C852
C862

1-164-362-11 CERAMIC CHIP

1-164-362-11 CERAMIC CHIP

470PF
470PF

5%
5%

50V
50V

73

HCD-CPX11
SP
Ref. No.
C872
C882

SUB PANEL
Part No.

SUB POWER

Description

1-164-362-11 CERAMIC CHIP

1-164-362-11 CERAMIC CHIP

Remark
470PF
470PF

5%
5%

Part No.

Description

8-729-141-73 TRANSISTOR
8-729-141-73 TRANSISTOR

R991
R992
R993
R994

1-537-114-21 TERMINAL BOARD (SPEAKER)

1-216-829-11
1-216-845-11
1-216-829-11
1-216-845-11

0 RY990
0 RY991

4.7K
100K
4.7K
100K

5%
5%
5%
5%

1/10W
1/10W
1/10W
1/10W

1-755-467-11 RELAY (POWER)

1-755-467-11 RELAY (POWER)
< TRANSFORMER >

SUB PANEL BOARD

***************

0 T991
1-437-676-11 TRANSFORMER, POWER (AEP, UK)
0 T991
1-437-677-11 TRANSFORMER, POWER (KR, AUS)
************************************************************

< DIODE >

8-719-046-36 DIODE SEL5921A-TP15 (CD NX)

A-4750-369-A TC BOARD, COMPLETE

******************

< TRANSISTOR >

8-729-027-43 TRANSISTOR

< CAPACITOR >

DTC114EKA-T146
C601
C602
C604
C605
C606

1-126-947-11
1-130-483-00
1-130-495-00
1-126-964-11
1-126-960-11

ELECT
MYLAR
MYLAR
ELECT
ELECT

47uF
0.01uF
0.1uF
10uF
1uF

20%
5%
5%
20%
20%

35V
50V
50V
50V
50V

C607
C608
C610
C611
C612

1-162-962-11
1-126-961-11
1-162-961-11
1-162-928-11
1-162-946-11

CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

470PF
2.2uF
330PF
120PF
27PF

10%
20%
10%
5%
5%

50V
50V
50V
50V
50V

C613
C614
C630
C632
C633

1-164-392-11
1-130-483-00
1-126-933-11
1-126-964-11
1-126-964-11

CERAMIC CHIP
MYLAR
ELECT
ELECT
ELECT

390PF
0.01uF
100uF
10uF
10uF

5%
5%
20%
20%
20%

50V
50V
16V
50V
50V

C634
C635
C639
C640
C641

1-126-964-11
1-126-960-11
1-126-964-11
1-126-947-11
1-126-961-11

ELECT
ELECT
ELECT
ELECT
ELECT

10uF
1uF
10uF
47uF
2.2uF

20%
20%
20%
20%
20%

50V
50V
50V
35V
50V

< DIODE >

C642
C643
C644
C645
C646

1-137-150-11
1-130-485-00
1-130-481-00
1-130-481-00
1-130-486-00

FILM
MYLAR
MYLAR
MYLAR
MYLAR

0.01uF
0.015uF
0.0068uF
0.0068uF
0.018uF

5%
5%
5%
5%
5%

100V
50V
50V
50V
50V

DIODE
DIODE
DIODE
DIODE
DIODE

< RESISTOR >

R870
R871
R874
R875
R876

METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
< RELAY >

L890
1-410-121-11 INDUCTOR
1.5mH
************************************************************

Q870

2SC3624A-T1L15L16
2SC3624A-T1L15L16

< RESISTOR >

1-564-505-21 PLUG, CONNECTOR 2P

1-564-505-11 PLUG, CONNECTOR 2P

< COIL >

D870

Remark

< TRANSISTOR >

Q990
Q991

< JACK >

J860

Ref. No.

50V
50V

< CONNECTOR >

CN850
CN870

TC

1-216-825-11
1-216-829-11
1-216-817-11
1-216-817-11
1-216-809-11

METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP

2.2K
4.7K
470
470
100

5%
5%
5%
5%
5%

1/10W
1/10W
1/10W
1/10W
1/10W

< SWITCH >

S816
1-762-875-21 SWITCH, KEYBOARD (CD NX)
S817
1-762-875-21 SWITCH, KEYBOARD ((CD) x)
************************************************************
SUB POWER BOARD
*****************
< CAPACITOR >
0 C991
0 C992
C993
C994

1-113-925-11
1-113-925-11
1-126-768-11
1-104-658-91

CERAMIC
CERAMIC
ELECT
ELECT

0.01uF
0.01uF
2200uF
100uF

20%
20%
20%
20%

< CONNECTOR >

CN990

1-564-321-00 PIN, CONNECTOR (3.96mm PITCH) 2P

250V
250V
16V
10V

D990
D991
D992
D993
D994

8-719-988-61
8-719-988-61
6-500-522-31
6-500-522-31
6-500-522-31

1SS355TE-17
1SS355TE-17
10EDB40-TB5
10EDB40-TB5
10EDB40-TB5

C647
C651
C652
C654
C655

1-126-964-11
1-126-947-11
1-130-483-00
1-130-495-00
1-126-964-11

ELECT
ELECT
MYLAR
MYLAR
ELECT

10uF
47uF
0.01uF
0.1uF
10uF

20%
20%
5%
5%
20%

50V
35V
50V
50V
50V

D995

6-500-522-31 DIODE 10EDB40-TB5

C656
C657
C658
C660
C661

1-126-960-11
1-162-962-11
1-126-961-11
1-162-961-11
1-162-928-11

ELECT
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP

1uF
470PF
2.2uF
330PF
120PF

20%
10%
20%
10%
5%

50V
50V
50V
50V
50V

< IC >
IC991

6-703-627-01 IC NJU7201L40 (T3)

The components identified by mark 0 or dotted

line with mark 0 are critical for safety.
Replace only with part number specified.

74

HCD-CPX11
TC
Ref. No.
C662
C663
C664
C681

Part No.

Description

1-162-946-11
1-164-392-11
1-130-483-00
1-162-968-11

CERAMIC CHIP
CERAMIC CHIP
MYLAR
CERAMIC CHIP

27PF
390PF
0.01uF
0.0047uF

5%
5%
5%
10%

Remark

Ref. No.

Part No.

Description

50V
50V
50V
50V

R640
R641
R642
0 R643

1-216-833-11
1-218-867-11
1-216-825-11
1-219-787-17

METAL CHIP
METAL CHIP
METAL CHIP
FUSIBLE

10K
6.8K
2.2K
5.6

5%
0.5%
5%
5%

1/10W
1/10W
1/10W
1/4W

0 R644
R645
R646
R647
R648

1-219-787-17
1-216-836-11
1-216-836-11
1-216-837-11
1-216-825-11

FUSIBLE
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP

5.6
18K
18K
22K
2.2K

5%
5%
5%
5%
5%

1/4W
1/10W
1/10W
1/10W
1/10W

R651
R652
R653
R654
R655

1-216-829-11
1-216-829-11
1-216-827-11
1-216-833-11
1-216-841-11

METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP

4.7K
4.7K
3.3K
10K
47K

5%
5%
5%
5%
5%

1/10W
1/10W
1/10W
1/10W
1/10W

R656
R657
R658
R659
R660

1-216-825-11
1-216-833-11
1-216-833-11
1-216-825-11
1-216-832-11

METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP

2.2K
10K
10K
2.2K
8.2K

5%
5%
5%
5%
5%

1/10W
1/10W
1/10W
1/10W
1/10W

R661
R680
R681
R682
R683

1-216-837-11
1-216-829-11
1-216-825-11
1-216-825-11
1-216-819-11

METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP

22K
4.7K
2.2K
2.2K
680

5%
5%
5%
5%
5%

1/10W
1/10W
1/10W
1/10W
1/10W

R684
R685
R686
R687
R688

1-216-827-11
1-216-827-11
1-216-827-11
1-216-841-11
1-216-829-11

METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP

3.3K
3.3K
3.3K
47K
4.7K

5%
5%
5%
5%
5%

1/10W
1/10W
1/10W
1/10W
1/10W

R689
R690
R691
R692
R693

1-216-829-11
1-216-829-11
1-216-833-11
1-216-829-11
1-216-841-11

METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP

4.7K
4.7K
10K
4.7K
47K

5%
5%
5%
5%
5%

1/10W
1/10W
1/10W
1/10W
1/10W

R694
R695

1-216-837-11 METAL CHIP

1-216-833-11 METAL CHIP

22K
10K

5%
5%

1/10W
1/10W

< CONNECTOR >

CN602
CN603

1-770-516-31 FFC/CONNECTOR, FPC (LIF (NON-ZIF)) 8P

1-784-780-11 CONNECTOR, FFC 19P

Remark

< DIODE >

D681

8-719-988-61 DIODE 1SS355TE-17

< IC >

IC601
IC602

6-702-130-01 IC HA12237F
8-759-508-69 IC BA3126N
< SHORT >

JR602

1-216-296-11 SHORT CHIP

< JUMPER RESISTOR >

JW630

1-216-864-11 SHORT CHIP

< COIL >

L601
L651

1-410-780-11 INDUCTOR
1-410-780-11 INDUCTOR

27mH
27mH

< TRANSISTOR >

Q639
Q640
Q641
Q642
Q643

8-729-119-77
8-729-029-66
8-729-801-93
8-729-142-46
8-729-142-46

TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR

2SA1175-FEK
DTC114ESA
2SD1387-3
2SC2001-LK
2SC2001-LK

Q680
Q681
Q691
Q692
Q693

8-729-029-66
8-729-029-40
8-729-027-43
8-729-027-43
8-729-140-04

TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR

DTC114ESA
DTA124ESA
DTC114EKA-T146
DTC114EKA-T146
2SB1116A-L

Q694

8-729-116-57 TRANSISTOR

< VARIABLE RESISTOR >

RV603
RV653

2SB1068-K

1-241-768-11 RES, ADJ CERMET

1-241-768-11 RES, ADJ CERMET

220K
220K

< RESISTOR >

< TRANSFORMER >
R601
R602
R603
R604
R605

1-216-829-11
1-216-829-11
1-216-827-11
1-216-833-11
1-216-841-11

METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP

4.7K
4.7K
3.3K
10K
47K

5%
5%
5%
5%
5%

1/10W
1/10W
1/10W
1/10W
1/10W

R606
R607
R608
R609
R610

1-216-825-11
1-216-833-11
1-216-833-11
1-216-825-11
1-216-832-11

METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP

2.2K
10K
10K
2.2K
8.2K

5%
5%
5%
5%
5%

1/10W
1/10W
1/10W
1/10W
1/10W

R611
R630
R631
R632
R633

1-216-837-11
1-216-857-11
1-216-837-11
1-216-821-11
1-216-833-11

METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP

22K
1M
22K
1K
10K

5%
5%
5%
5%
5%

1/10W
1/10W
1/10W
1/10W
1/10W

R635

1-216-809-11 METAL CHIP

100

5%

1/10W

T601
1-423-980-11 TRANSFORMER, BIAS OSCILLATION
************************************************************
MISCELLANEOUS
***************
60
63
69
71
102

1-824-192-11
1-796-456-31
1-773-120-11
1-773-110-11
1-769-912-11

WIRE (FLAT TYPE) (8 CORE)

DECK, MECHANICAL (CMAL1Z-236A)
WIRE (FLAT TYPE) (19 CORE)
WIRE (FLAT TYPE) (19 CORE)
WIRE (FLAT TYPE) (9 CORE)

0 151
0 151
0 151
155
155

1-769-079-23
1-777-071-83
1-783-203-13
1-777-353-11
1-824-486-11

CORD, POWER (KR)

CORD, POWER (AEP, UK)
CORD, POWER (AUS)
FLAT CABLE (15 CORE) (AEP, UK)
WIRE (FLAT TYPE) (11 CORE) (KR, AUS)

The components identified by mark 0 or dotted

line with mark 0 are critical for safety.
Replace only with part number specified.

75

HCD-CPX11

Ref. No.

Part No.

Description

156
156
156
158
0 201

1-693-603-31
1-693-604-11
1-693-605-11
1-773-105-11
1-468-730-11

TUNER (FM/AM) (AUS)

TUNER (FM/AM) (AEP, UK)
TUNER (FM/AM) (KR)
WIRE (FLAT TYPE) (19 CORE)
REGULATOR, SWITCHING

203
204
413
462
0 556

1-500-484-21
1-773-158-11
1-763-967-11
1-452-925-21
8-820-244-01

CLAMP, SLEEVE FERRITE

WIRE (FLAT TYPE) (21 CORE)
MOTOR, DC
MAGNET ASSY
OPTICAL PICK-UP (KSM-215DCP/C2NP)

557
559
M701

Remark

1-775-241-11 WIRE (FLAT TYPE) (27 CORE)

1-827-992-11 WIRE (FLAT TYPE)(16 CORE)
X-2021-530-1 MOTOR (PULLEY) ASSY (LOADING)

The components identified by mark 0 or dotted

line with mark 0 are critical for safety.
Replace only with part number specified.

76

HCD-CPX11

MEMO

77

HCD-CPX11

REVISION HISTORY
Clicking the version allows you to jump to the revised page.
Also, clicking the version at the upper right on the revised page allows you to jump to the next revised
page.
Ver.

Date

Description of Revision

1.0

2004.04

New

1.1

2004.04

Correction in test mode

(ENG-04001)