TL082 TL082A - TL082B

GENERAL PURPOSE J-FET DUAL OPERATIONAL AMPLIFIER

. . . . . . .

WIDE COMMON-MODE (UP TO VCC+) AND DIFFERENTIAL VOLTAGE RANGE LOW INPUT BIAS AND OFFSET CURRENT OUTPUT SHORT-CIRCUIT PROTECTION HIGH INPUT IMPEDANCE JFET INPUT STAGE INTERNAL FREQUENCY COMPENSATION LATCH UP FREE OPERATION HIGH SLEW RATE : 16V/s (typ)

N DIP8 (Plastic Package)

D SO8 (Plastic Micropackage)

P TSSOP8 (Thin Shrink Small Outline Package)

DESCRIPTION The TL082, TL082A and TL082B are high speed JFET input dual operational amplifiers incorporating well matched, high voltage JFET and bipolar transistors in a monolithic integrated circuit. The devices featurehigh slewrates, low input bias and offset current, and low offset voltage temperature coefficient. PIN CONNECTIONS (top view)

ORDER CODES
Part Number TL082M/AM/BM TL082I/AI/BI TL082C/AC/BC Temperature Range 55 C, +125 C 40oC, +105oC 0 C, +70 C
o o o o

Package N D P

Examples : TL082CD, TL082IN

1 2 3 4 + +

8 7 6 5

1 2 3 4 5 6 7 8

Output 1 Inverting input 1 Non-inverting input 1 VCC Non-inverting input 2 Inverting input 2 Output 2 VCC+

January 1999

1/10

TL082 - TL082A - TL082B

SCHEMATIC DIAGRAM

VCC

No n- inver t ing i nput I nver t ing input

1 0 0

20 0

Output
1 0 0

30k

1/2 T L082

8.2k

1.3k
V CC

35k

1.3k

35k

1 0 0

ABSOLUTE MAXIMUM RATINGS

Symbol VCC Vi Vid Ptot Toper Supply Voltage - (note 1) Input Voltage - (note 3) Differential Input Voltage - (note 2) Power Dissipation Output Short-circuit Duration - (note 4) Operating Free Air Temperature Range TL082C,AC,BC TL082I,AI,BI TL082M,AM,BM Parameter Value 18 15 30 680 Infinite 0 to 70 40 to 105 55 to 125 65 to 150
o

Unit V V V mW C

Tstg
Notes :

Storage Temperature Range

1. All voltage values, except differential voltage, are with respect to the zero reference level (ground) of the supply voltages where the zero reference level is the midpoint between VCC+ and VCC. 2. Differential voltages are at the non-inverting input terminal with respect to the inverting input terminal. 3. The magnitude of the input voltage must never exceed the magnitude of the supply voltage or 15 volts, whichever is less. 4. The output may be shorted to ground or to either supply. Temperature and /or supply voltages must be limited to ensure that the dissipation rating is not exceeded.

2/10

TL082 - TL082A - TL082B

ELECTRICAL CHARACTERISTICS VCC = 15V, Tamb = 25oC (unless otherwise specified)
Symbol Vio Parameter Input Offset Voltage (R S = 50) o TL082 Tamb = 25 C TL082A TL082B TL082 Tmin. Tamb Tmax. TL082A TL082B Input Offset Voltage Drift Input Offset Current * o Tamb = 25 C Tmin. Tamb Tmax. Input Bias Current * o Tamb = 25 C Tmin. Tamb Tmax. Large Signal Voltage Gain (RL = 2k, VO = 10V) Tamb = 25oC Tmin. Tamb Tmax. Supply Voltage Rejection Ratio (R S = 50) o Tamb = 25 C Tmin. Tamb Tmax. Supply Current, per Amp, no Load Tamb = 25oC Tmin. Tamb Tmax. Input Common Mode Voltage Range Common Mode Rejection Ratio (RS = 50) o Tamb = 25 C Tmin. Tamb Tmax. Output Short-circuit Current o Tamb = 25 C Tmin. Tamb Tmax. Output Voltage Swing o Tamb = 25 C Tmin. Tamb Tmax. SR tr KOV GBP Ri THD en m VO1/VO2 RL RL RL RL = = = = 2k 10k 2k 10k 11 50 25 80 80 TL082I,M,AC,AI, AM,BC,BI,BM Min. Typ. 3 3 1 Max. 10 6 3 13 7 5 Min. TL082C Typ. 3 Max. mV 10 13 V/ C 100 4 400 20 pA nA pA nA V/mV 200 25 15 70 70 2.5 2.5 11 200 dB 86 86 mA 1.4 +15 -12 86 1.4 +15 -12 86 mA 10 10 10 12 10 12 8 40 60 60 10 10 10 12 10 12 8 40 60 60 V 12 13.5 12 13.5 V/s s % 10 2.5 4 10
12 o

Unit

DV io Iio

10 5 100 4 200 20

10 5

Iib

20

20

Avd

SVR

ICC

2.5 2.5 V dB

Vicm CMR

80 80

70 70

Ios VOPP

Slew Rate (Vin = 10V, RL = 2k, CL = 100pF, o Tamb = 25 C, unity gain) Rise Time (Vin = 20mV, RL = 2k, C L = 100pF, Tamb = 25oC, unity gain) Overshoot (Vin = 20mV, RL = 2k, C L = 100pF, o Tamb = 25 C, unity gain) Gain Bandwidth Product (f = 100kHz, Tamb = 25oC, Vin = 10mV, R L = 2k, C L = 100pF) Input Resistance Total Harmonic Distortion (f = 1kHz, AV = 20dB, RL = 2k, C L = 100pF, Tamb = 25oC, VO = 2VPP) Equivalent Input Noise Voltage (f = 1kHz, R s = 100) Phase Margin Channel Separation (Av = 100)

16 0.1

16 0.1 10

MHz 2.5 4 10
12

0.01 15 45 120

0.01 15 45 120 nV Hz Degrees dB

* The input bias currents are junction leakage currents which approximately double for every 10oC increase in the junction temperature.

3/10

TL082 - TL082A - TL082B

MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE VERSUS FREQUENCY
30 MAXIMUM PEAK-TO-PEAKOUTPUT VOLTAGE (V) V CC = 25 20 V CC = 15 10 5 0 100 10V 15V
R L = 2k T a m b = + 25 C S ee Fig ure 2

MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE VERSUS FREQUENCY

MAXIMUMPEAK-TO-PEAK OUTPUT VOLTAGE (V)

30 25 20 15 10 5 0 100 1K 10K 100K

V CC =
5V

V CC = 15V VCC = 10V

R L= 10k Tamb = +25 C See Figure 2

V CC =

5V

1K

10K

100K

1M

10M

1M

10M

FREQUENCY (Hz)

FREQUENCY (Hz)

MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE VERSUS FREQUENCY

MAXIMUMPEAK-TO-PEAK OUTPUT VOLTAGE (V) 30

MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE VERSUS FREE AIR TEMP.

Ta mb = +25 C
25 20 15

VCC =

15V

R L = 2k S ee Figure 2

MAXIMUM PEAK-TO-PEAKOUTPUT VOLTAGE (V)

30 25 20

R
15 10 5 0 -7 5 -5 0 - 25 0 25 50

L L

= 1 0 k = 2 k

Ta mb = -55 C
10 5 0

VC C =

15 V

Ta mb = +125 C 10k 40k 100k 400k 1M 4M 10M

S e e F i g u re 2 75 -50 125

FREQUENCY (Hz)

T E MP ER AT U R E ( C )

MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE VERSUS LOAD RESISTANCE

30 25
VOLTAGE (V)

MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE VERSUS SUPPLY VOLTAGE

30 25
RL = 10 k Tamb = +25C

MAXIMUM PEAK-TO-PEAK OUTPUT

V CC = 15V Tamb = +25C See Figure 2

20
15 10

MAXIMUM PEAK-TO-PEAKOUTPUT VOLTAGE (V)

20
15 10

5
0
0.1 0.2 0.4 0.7 1 2 4 7 10

5
0 2
4 6 8 10 12 SUPPLY VOLTAGE ( V)

14

16

LOAD RESISTANCE (k

4/10

TL082 - TL082A - TL082B

INPUT BIAS CURRENT VERSUS FREE AIR TEMPERATURE LARGE SIGNAL DIFFERENTIAL VOLTAGE AMPLIFICATION VERSUS FREE AIR TEMPERATURE
1000

100 V CC = INPUT BIAS CURRENT (nA) 10 15V

DIFFERENTIAL VOLTAGE AMPLIFICATION (V/V)

400 200 100 40 20 10 4 2 1 -75 V CC = VO = R

L

15V 10V

0.1

= 2k

0.01 -50

-25

25

50

75

100

125

-50

-25

25

50

75

100

125

TEMPERATURE (C)

TEMPERATURE (C)

LARGE SIGNAL DIFFERENTIAL VOLTAGE AMPLIFICATION AND PHASE SHIFT VERSUS FREQUENCY

TOTAL POWER DISSIPATION VERSUS FREE AIR TEMPERATURE

250

DIFFERENTIAL VOLTAGE AMPLIFICATION(V/V)

100
PHASE SHIFT (right s ca le )

DIFFERENTIAL VOLTAGE AMPLIFICATION (left s ca le)

180

TOTAL POWER DISSIPATION (mW)

225 200 175 150 125 100 75 50 25 0 -75 -50 -25 0 25 50

V CC = No signal No load

15V

10

1 100

R = 2k L C L = 100pF V CC = 15V T amb = +125 C

1K 10K 100K 1M 10M FREQUENCY (Hz)

90

75

100

125

TEMPERATURE (C)

SUPPLY CURRENT PER AMPLIFIER VERSUS FREE AIR TEMPERATURE

2.0

SUPPLY CURRENT PER AMPLIFIER VERSUS SUPPLY VOLTAGE

2.0 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0 SUPPLY CURRENT (mA) Tamb = +25C No signal No load

1.8 SUPPLY CURRENT (mA) 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0 -75 -50 -25 0 25 50

V CC = No signal No load

15V

75

100

125

TEMPERATURE (C)

4 6 10 12 14 8 SUPPLY VOLTAGE ( V)

16

5/10

TL082 - TL082A - TL082B

COMMON MODE REJECTION RATIO VERSUS FREE AIR TEMPERATURE
89 COMMON MODE MODE REJECTION RATIO (dB) 88 87 86 85 84 83 -75

VOLTAGE FOLLOWER LARGE SIGNAL PULSE RESPONSE

INPUT AND OUTPUT VOLTAGES (V) 6 4 2 0 -2 -4 -6 0 VCC = 15V R L = 2 k C L= 100pF Tam b = +25 C 0.5 1 1.5 2 2.5 3 3.5 OUTP UT INPUT

R L = 1 0 k VC C = 15V

-50

-25

25

50

75

100

125

TEMPERATURE (C)

TIME (s )

OUTPUT VOLTAGE VERSUS ELAPSED TIME

28
OUTPUT VOLTAGE (mV)

EQUIVALENT INPUT NOISE VOLTAGE VERSUS FREQUENCY

70
OVERSHOOT

24 20 16 12 8 4 0 -4
10%

60 EQUIVALENT INPUT NOISE VOLTAGE (nV/VHz)

90%

VCC = 15V A V = 10 R S = 100 T amb = +25C

50 40 30 20 10 0 10 40 100 400 1k 4k

tr

R L = 2k Tamb = +25 C

= 15V CC

0.1

0.2

0.3

0.4

0.5

0.6

0.7

10k

40k 100k

TIME (s)

FREQUENCY (Hz)

TOTAL HARMONIC DISTORTION VERSUS FREQUENCY

1 TOTAL HARMONIC DISTORTION (%) 0.4 0.1 0.04 0.01 0.004 0.001 100 400 1k 4k 10k 40k 100k FREQUENCY (Hz) VV = = 15V 15V CC CC == 11 AA VV VV = 6V O (rms) (rms) = 6V
O

T amb +25 C T amb= = +25 C

6/10

TL082 - TL082A - TL082B

PARAMETER MEASUREMENT INFORMATION Figure 1 : Voltage Follower Figure 2 : Gain-of-10 Inverting Amplifier

10k

1/2
TL082

1k

eI

1/2
TL082

eo

eo
RL

eI

CL = 100pF

RL = 2k

CL = 100pF

TYPICAL APPLICATION 100KHz QUADRUPLE OSCILLATOR

1N 4148

18k *

-15V
1k

18pF
18pF 1/2 TL082
88.4k

88.4k

6 sin t

1/2 TL082
1k

6 cos t

18pF
88.4k

1N 4148

18k *

+15V

* These resistor values may be adjusted for a symmetrical output

7/10

TL082 - TL082A - TL082B

PACKAGE MECHANICAL DATA 8 PINS - PLASTIC DIP

Dimensions A a1 B b b1 D E e e3 e4 F i L Z

Min. 0.51 1.15 0.356 0.204 7.95

Millimeters Typ. 3.32

Max.

Min. 0.020 0.045 0.014 0.008 0.313

Inches Typ. 0.131

Max.

1.65 0.55 0.304 10.92 9.75 2.54 7.62 7.62 6.6 5.08 3.81 1.52

0.065 0.022 0.012 0.430 0.384 0.100 0.300 0.300 0260 0.200 0.150 0.060

3.18

0.125

8/10

TL082 - TL082A - TL082B

PACKAGE MECHANICAL DATA 8 PINS - PLASTIC MICROPACKAGE (SO)

Dimensions A a1 a2 a3 b b1 C c1 D E e e3 F L M S

Min. 0.1 0.65 0.35 0.19 0.25 4.8 5.8

Millimeters Typ.

Max. 1.75 0.25 1.65 0.85 0.48 0.25 0.5 45 (typ.) 5.0 6.2
o

Min. 0.004 0.026 0.014 0.007 0.010 0.189 0.228

Inches Typ.

Max. 0.069 0.010 0.065 0.033 0.019 0.010 0.020 0.197 0.244

1.27 3.81 3.8 0.4 4.0 1.27 0.6 8 (max.)

o

0.050 0.150 0.150 0.016 0.157 0.050 0.024

9/10

TL082 - TL082A - TL082B

PACKAGE MECHANICAL DATA 8 PINS - THIN SHRINK SMALL OUTLINE PACKAGE

Dim. A A1 A2 b c D E E1 e k l

Millimeters Min. 0.05 0.80 0.19 0.09 2.90 4.30 0

o

Inches Max. 1.20 0.15 0.01 0.031 0.007 0.003 0.114 0.169 0
o

Typ.

Min.

Typ.

Max. 0.05 0.006

1.00

1.05 0.30 0.20

0.039

0.041 0.15 0.012

3.00 6.40 4.40 0.65

3.10 4.50 8
o

0.118 0.252 0.173 0.025

0.122 0.177 8
o

0.50

0.60

0.75

0.09

0.0236

0.030

Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publ ication supersedes and replaces all information previously suppli ed. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a trademark of STMicroelectronics 1999 STMicroelectronics Printed in Italy All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - Canada - China - France - Germany - Italy - Japan - Korea - Malaysia - Malta - Mexico - Morocco The Netherlands - Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A. http://www.st.com

10/10

This datasheet has been download from: www.datasheetcatalog.com Datasheets for electronics components.