Scribd
Upload
49 views

Final Assembly

This document contains assembly drawings and part lists for a mixer assembly. It includes section views, detail views, and general notes on the assembly. The general notes specify the rated power of the machine, assembly instructions, inspection procedures, and maintenance schedule. Dimensions and tolerances are provided, along with material and hardness specifications.

Uploaded by

Ian As
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
49 views

Final Assembly

This document contains assembly drawings and part lists for a mixer assembly. It includes section views, detail views, and general notes on the assembly. The general notes specify the rated power of the machine, assembly instructions, inspection procedures, and maintenance schedule. Dimensions and tolerances are provided, along with material and hardness specifications.

Uploaded by

Ian As
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

REVISIONS 36.38 5 REV.

0 DESCRIPTION ASSEMBLY DWG CREATED DATE 12/12/12 APPROVED

4 24.69 D

8.00

SECTION A-A 2

15

20

6 F 18

39

46

44

SECTION D-D SCALE 1 : 8

75.05 7 7

34.00

A DETAIL F SCALE 1 : 6 7

DETAIL C SCALE 1 : 2

B 2 21 6 C 19 17 21 10 11 56.69
GENERAL NOTES:

ITEM NO. 1 2 3 4 5

PART NUMBER A-002 A-001 TBD TBD TBD TBD TBD TBD TBD TBD TBD TBD TBD TBD TBD TBD TBD TBD TBD TBD TBD
MIXER ASSEMBLY

DESCRIPTION MAIN FRAME GEARBOX MOTOR PULLEY - MOTOR PULLEY - INTERMEDIATE SHAFT COUPLING V-BELT BELT COVER KEY MOTOR KEY PULLEY KEY COUPLING 0.75 - 16 X 3 SHCS 1.0 - 8 X 8 SHCS 1.25 X 12 X 3 SHCS 1.25 - 12 X 1.5 SHCS 0.75 - 16 X 1.5 SHCS 0.75 - 16 X 2 SHCS 1.25 X 0.25 FENDER WASHER 0.75 X 0.25 FENDER WASHER 1.25 LOCK WASHER 0.75 LOCK WASHER

Default/ QTY. 1 1 1 1 1 1 2 1 1 1 1 4 2 4 1 1 4 1 1 1 1

1.- RATED MACHINE POWER: 29HP 2.- ASSEMBLY INSTRUCTIONS: -BOLT GEARBOX TO PEDESTAL -BOLT MOTOR TO PLATE -MOUNT PULLEYS ON CORRECT SHAFTS -PLACE BELTS ON PULLEYS -TENSION MOTOR TO CORRECT LEVEL -PLACE COVER ON BELT -BOLT COUPLING ON 3.- ENSURE ALL INSPECTION PROCEDURES OCCUR PRIOR TO USE 4.- CHECK OIL EVERY 5000 HRS E
TOLERANCE INFORMATION

8.00

6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 PART NUMBERS:

1.70 SECTION B-B B

UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES MATERIAL: TBD AND THE TOLERANCES ARE: HARDNESS: TBD FRACTIONS DECIMALS ANGLES FINISH: TBD 1/64 .XXXX = .0005" X = 015' DRAWN: FELIPE B. DATE : 12/12/2012 .XXX = .005" X.X = 005' APPROVED: DATE : .XX = .01" JOB No: TBD SCALE: 1:12 THIRD ANGLE PROJECTION: ITEM No :TBD REV : 0 OF: QUANTITY:TBD SHEET:
1 1

MECH 500 MACHINE DESIGN

FELIPE BASTOS TADEH ARMENIAN RILEY FOUND

You might also like