Scribd
Upload
697 views1 page

MCC-Size

This document contains calculations for sizing switchgear and motor control centers (MCCs) for a project. It lists equipment items and quantities, then calculates the number of modules and panels required. Based on the modules and panels, it estimates the overall width and total heat loss of the switchgear/MCC. Notes provide additional specifications about the configuration, dimensions, clearances and extensibility of the switchgear/MCC.

Uploaded by

Saraswatapalit
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLS, PDF, TXT or read online on Scribd
697 views1 page

MCC-Size

This document contains calculations for sizing switchgear and motor control centers (MCCs) for a project. It lists equipment items and quantities, then calculates the number of modules and panels required. Based on the modules and panels, it estimates the overall width and total heat loss of the switchgear/MCC. Notes provide additional specifications about the configuration, dimensions, clearances and extensibility of the switchgear/MCC.

Uploaded by

Saraswatapalit
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLS, PDF, TXT or read online on Scribd
You are on page 1/ 1

PROJECT: DATE: SWITCHGEAR / MCC SIZING CALCULATION FOR:

STANDARD TIER
RQD. TOTAL MODULES PER ITEM MODULES REQUIRED

STANDARD TIER
RQD. TOTAL MODULES PER ITEM MODULES REQUIRED

ITEM DESCRIPTION DOL <= 15kW DOL >15kW<=55kW DOL >55kW<=110kW DOL >110kW<=250kW S/D <= 15kW S/D >15kW<=55kW S/D >55kW<=110kW S/D >110kW<=250kW VSD <= 15kW VSD >15kW <= 75 kW S-STR >15kW <= 75 kW F/SW TO 63A F/SW 100A F/SW 100A-400A F/SW 400A-800A

NO.OF ITEMS

1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

1 2 3 5 2 4 6 10 5 10 10 1 2 3 5 TOTAL (A)=

1 2 3 5 2 4 6 10 5 10 10 1 2 3 5 69

ITEM DESCRIPTION 400/230v DISBOARD 110v DISBOARD 110 VOLT Tx PLC SPARE MODULES

NO.OF ITEMS

5 2 3

TOTAL (B)= 69 10 7

TOTAL NUMBER OF MODULES REQUIRED SO FAR (A+B)= THE NUMBER OF MODULES PER TIER = NUMBER OF COMPLETE TIERS REQUIRED FOR THESE MODULES = WIDTH OF A TYPICAL STANDARD TIER (mm) = (say 600mm for front and rear access; 800mm for front only access) FULL HEIGHT PANELS
RQD. RQD. PANEL TOTAL RQD.

FULL HEIGHT PANELS


RQD. RQD. PANEL TOTAL RQD.

PANEL DESCRIPTION VSD >75kW<=125kW VSD >125kW S-STR >75kW<=125kW S-STR >125kW ACB METERING

NO.OF PANELS

WIDTH(mm) WIDTH(mm)

800 1000 800 1000 1000 1000 TOTAL(C)=

PANEL DESCRIPTION COMMON CONTROLS PLC TELEMETRY INSTRUMENTATION

NO.OF PANELS

WIDTH(mm) WIDTH(mm)

800 1200 1200 800

TOTAL(D)=

RESULTS:
THE ESTIMATED TOTAL OVERALL WIDTH OF THIS SWITCHGEAR / MCC = FOR AN AVERAGE HEAT LOSS PER TIER OR PANEL OF THE ESTIMATED TOTAL HEAT LOSS FOR THIS SWITCHGEAR / MCC = mm

300 2.10

watts kW

NOTES 1. THE MCC WILL BE FRONT AND REAR ACCESS / FRONT ACCESS ONLY / BACK TO BACK 2. LINEUP HEIGHT WILL BE 2200mm OR AS VENDOR 3. LINEUP DEPTH WILL BE 550mm (PLUS 250 FOR CABLE BOXES; 350 FOR S/D CABLE BOXES) 4. CABLE ENTRY WILL BE FROM ABOVE / BELOW 5. MINIMUM CLEARANCE OF 1000mm WILL BE REQUIRED IN FRONT 6. MINIMUM CLEARANCE OF 500mm WILL BE REQUIRED TO REAR 7. THE MCC WILL BE EXTENSIBLE AT BOTH ENDS

You might also like