Scribd Logo
Upload

Welcome to Scribd!

  • 9K views

    Evo 4-5-6 Conversion To Evo7-8 ECU Pinout Diagrams

    Uploaded by

    rjlaforteza
    The document provides wiring information for swapping an Evo 7 ECU into an Evo 4, including which pins to connect and disconnect between the different connector blocks. It lists the pin numbers and functions for various connectors on both vehicles. It also provides some notes on specific wiring changes needed such as connecting the radiator fan relays and secondary air system solenoid.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as XLS, PDF, TXT or read online from Scribd

    Evo 4-5-6 Conversion To Evo7-8 ECU Pinout Diagrams

    Uploaded by

    rjlaforteza
    9K views10 pages
    The document provides wiring information for swapping an Evo 7 ECU into an Evo 4, including which pins to connect and disconnect between the different connector blocks. It lists the pin numbers and functions for various connectors on both vehicles. It also provides some notes on specific wiring changes needed such as connecting the radiator fan relays and secondary air system solenoid.

    Original Description:

    Mitsubishi Evo 4, 5, 6 conversion to Evo 7, 8 ECU Pinout Diagrams

    Original Title

    Evo 4-5-6 conversion to Evo7-8 ECU Pinout Diagrams

    Copyright

    © Attribution Non-Commercial (BY-NC)

    Available Formats

    XLS, PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document provides wiring information for swapping an Evo 7 ECU into an Evo 4, including which pins to connect and disconnect between the different connector blocks. It lists the pin numbers and functions for various connectors on both vehicles. It also provides some notes on specific wiring changes needed such as connecting the radiator fan relays and secondary air system solenoid.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as XLS, PDF, TXT or read online from Scribd
    Download as xls, pdf, or txt
    9K views10 pages

    Evo 4-5-6 Conversion To Evo7-8 ECU Pinout Diagrams

    Uploaded by

    rjlaforteza
    The document provides wiring information for swapping an Evo 7 ECU into an Evo 4, including which pins to connect and disconnect between the different connector blocks. It lists the pin numbers and functions for various connectors on both vehicles. It also provides some notes on specific wiring changes needed such as connecting the radiator fan relays and secondary air system solenoid.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as XLS, PDF, TXT or read online from Scribd
    Download as xls, pdf, or txt
    of 10

    USDM Rom / wiring only Possible fault codes Yellow Tabs IC sprayer system Optional Red Tabs wiring

    changes for ECU swap Evo 7 ECU JDM Pin


    1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 No. 1 Injector No. 3 Injector Fuel Pressure Solenoid Idle Speed Control (ISC) Motor Coil (A1) ISC Motor Coil (B1) EGR Solenoid A/C compressor relay Evaporate Emission Purge Solenoid Ignition Power Transistor (for cyl 1&4) Turbo Wastegate Solenoid 12V Switched Power Supply Chassis Ground No. 2 Injector No. 4 Injector ISC Motor Coil (A2)

    Evo 4

    Connector 59 /C121
    No.1 injector No.3 injector Fuel pressure control valve Idle Speed Control (ISC) Motor Coil (A1) ISC Motor Coil (B1) Secondary air control solenoid valve Fuel pump relay 1 Ignition Power Transistor (for cyl 1&4) Turbo Wastegate Solenoid 12V Switched Power Supply Chassis Ground No.2 injector No.4 injector ISC Motor Coil (A2)

    18 19 20 21 22 23 24 25 26

    ISC Motor Coil (B2) Volume Air Flow Sensor Reset Signal Radiator Fan Motor Relay (PWM Output) Fuel Pump Relay 2 Ignition Power Transistor (for cyl 2&3) A/C load signal 12V Switched Power Supply Chassis Ground

    ISC Motor Coil (B2) Volume Air Flow Sensor Reset Signal Radiator fan motor relay (HI) Radiator fan motor relay (Lo) A/C compressor relay Ignition Power Transistor (for cyl 2&3) 12V Switched Power Supply Chassis Ground

    Pin
    31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46

    Connector 60/C119
    Condensor Fan Relay (Hi) Generator G Terminal Condensor Fan Relay (Lo) Intercooler Sprayer activation light Check Engine Light (Service Engine Soon) Power Steering Pressure Switch (Input) Engine control relay Fuel Pump Relay 3 (Additional pressure for higher loads) Sensor Ground (IAT, Cam and Crank Angle Sensors) Alternator FR terminal Clutch Position Switch (Input) Intercooler Sprayer switch (Auto) A/C pressure switch Fuel Tank Level (Input) USDM Alternator G terminal

    Check Engine Light (Service Engine Soon) Power Steering Pressure Switch (Input) Engine control relay Fuel pump relay No.2 (Additional pressure for higher loads) Exhaust temperature warning lamp Alternator FR terminal

    A/C pressure switch

    Pin
    51 52 53 54 55 56 Imobilizer ECU (Anti-Theft)

    Connector 61/C117
    Secondary Air System solenoid O2 Sensor Heater (rear) EVAP Vent Solenoid Valve USDM / IC spray relay JDM Diagnostic OBDII Pin 1

    Diagnostic OBDII Pin 1

    57 58 59 60 61 62

    IC spray relay USDM Tachometer signal O2 Sensor Heater (front) Fuel Tank Differential Pressure Sensor USDM Diagnostic OBDII Pin 7 - K Line

    Tachometer signal

    Diagnostic OBDII Pin 7 - K Line

    Pin
    71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 Starter Signal Intake Air Temp Sensor Signal Manifold Differential Pressure Sensor USDM Sub Fuel Level Sensor USDM O2 Sensor (rear) O2 Sensor (front) Fuel Temperature Sensor USDM Knock Sensor ECU Init signal Backup Power Supply (12v Constant Power) 5V Sensor Power Supply (TPS, MDP, Baro, Fuel Tank Press Sensor) Ignition switch-IG Engine coolant temperature sensor Throttle Position Sensor Signal Barometric Pressure Sensor Signal Vehicle Speed Sensor Signal AYC/ACD signal Camshaft Position Sensor Signal Crankshaft Position Sensor Signal Volume Air Flow Sensor Signal Intercooler Sprayer switch (Manual) Sensor Ground (O2 Sensors, Coolant Temp, TPS, MDP, Fuel Tank Press Sensor)

    Connector 62/ C115


    Starter Signal Intake Air Temp Sensor Signal High temperature sensor O2 Sensor (front) High temp sensor Ground Knock Sensor Backup Power Supply (12v Constant Power) 5V Sensor Power Supply (TPS, MDP, Baro, Fuel Tank Press Sensor) Ignition switch-IG Engine coolant temperature sensor Throttle Position Sensor Signal Barometric Pressure Sensor Signal Vehicle Speed Sensor Signal Idle position switch Camshaft Position Sensor Signal Crankshaft Position Sensor Signal Volume Air Flow Sensor Signal Body earth Ground for sensors

    Recap Swap cables 8 and pin 22 fuel pump relay with AC control relay

    Disconnect pin 87 AYC/ACD signal Connect Cable 20 to pin 32 Rad Fan Hi to condensor fan Hi Connect Cable 21 to pin 34 Rad fan lo to condensor fan lo Connect cable 6 Secondary air system to pin 53 of Evo 7 ECU disconnect pin 91 or rewire for IC sprayer manual operation Evo 4 only disconnect pin 40 and ground cable or connect to pin 92 sensor ground Evo 4 only disconnect pin 33 if alternator is not charging battery

    Evo 5/6

    Operating Conditions
    2 3 (at 20degC) 2 3 (at 20degC)

    No.1 injector No.3 injector Fuel pressure control valve Idle Speed Control (ISC) Motor Coil (A1) ISC Motor Coil (B1) Secondary air control solenoid valve Fuel pump relay 1 Ignition Power Transistor (for cyl 1&4) Turbo Wastegate Solenoid 12V Switched Power Supply Chassis Ground No.2 injector No.4 injector ISC Motor Coil (A2)

    2 3 (at 20degC) 2 3 (at 20degC)

    ISC Motor Coil (B2) Volume Air Flow Sensor Reset Signal Radiator fan motor relay (HI) Radiator fan motor relay (Lo) A/C compressor relay Ignition Power Transistor (for cyl 2&3) 12V Switched Power Supply Chassis Ground

    Fan at high speed (coolant temperature: 105C or above) Fan at low speed (coolant temperature: 90 100C)

    Alternator G terminal

    Check Engine Light (Service Engine Soon) Power Steering Pressure Switch (Input) Engine control relay Fuel pump relay No.2 (Additional pressure for higher loads) Sensor Ground (IAT, Cam and Crank Angle Sensors) Alternator FR terminal

    A/C pressure switch

    Diagnostic OBDII Pin 1

    Tachometer signal O2 Sensor Heater (front) Diagnostic OBDII Pin 7 - K Line

    Starter Signal Intake Air Temp Sensor Signal

    O2 Sensor (front) Knock Sensor ECU Init signal Backup Power Supply (12v Constant Power) 5V Sensor Power Supply (TPS, MDP, Baro, Fuel Tank Press Sensor) Ignition switch-IG Engine coolant temperature sensor Throttle Position Sensor Signal Barometric Pressure Sensor Signal Vehicle Speed Sensor Signal Idle position switch Camshaft Position Sensor Signal Crankshaft Position Sensor Signal Volume Air Flow Sensor Signal Body earth Ground for sensors

    n 92 sensor ground y

    You might also like