Scribd
Upload
133 views1 page

Van'S Aircraft, Inc.: Figure 2: Installing Pins in The

This document provides instructions for routing wiring harnesses in a Van's Aircraft RV-12 aircraft. It outlines 4 steps: 1) Route remaining wires from one harness through two bulkheads, 2) Route additional wires and a static line through multiple bulkheads, components and panels, 3) Route two harnesses through a bushing and connect them to a connector, and 4) Route the connected harnesses up to a fuselage frame, replacing ties as needed. Diagrams show the routing paths and connector pin locations.

Uploaded by

Mark Evan Salutin
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
133 views1 page

Van'S Aircraft, Inc.: Figure 2: Installing Pins in The

This document provides instructions for routing wiring harnesses in a Van's Aircraft RV-12 aircraft. It outlines 4 steps: 1) Route remaining wires from one harness through two bulkheads, 2) Route additional wires and a static line through multiple bulkheads, components and panels, 3) Route two harnesses through a bushing and connect them to a connector, and 4) Route the connected harnesses up to a fuselage frame, replacing ties as needed. Diagrams show the routing paths and connector pin locations.

Uploaded by

Mark Evan Salutin
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

VAN'S AIRCRAFT, INC.

Step 1: Route the remaining wires of the WH-RV12-TUNNEL harness back thorough the F-1206A and F-1207B Baggage Bulkheads. Step 2: Route WH-P30 Trim Wires and Static Line from the tailcone forward through the F-1207B and F-1206A Bulkheads, fuel pump cushioned clamp, F-1204 Center Section Assembly, F-1276C Systems Blocks, F-1203A and F-1202F Bulkheads, fuel flow cushioned clamp, around the back of the rudder pedals and up through the F-1202B Panel Base. Step 3: Route the WH-RV12-OAT harness and WH-RV12-TUNNEL harness through a snap bushing in the F-1207D-L Baggage Bulkhead Channel. Slip the ES HST 3/16 X 2" Heat Shrink over the ends of the wires. Insert the pins on the ends of both wiring harnesses through the heat shrink and into the ES 205203-3 9-Pin D-Sub Female connector according to Figure 2. Check with a gentle tug that each wire has snapped into place. Center the ES HST 3/16 X 2" Heat Shrink around the location where the wires will exit the ES 9 PIN BSHELL. Activate the heat shrink. Step 4: Following the routing of the Static Line, route the harnesses attached to the 9-Pin D-Sub up to the top center of the F-1208 Fuselage Frame, replacing plastic tie wraps as required.

ES 205203-3 ES HST 3/16 X 2"

F-1208 FUSELAGE FRAME

WH-RV12-OAT WH-RV12-TUNNEL

PLASTIC TIE WRAP 4.5" (REPLACE AS NECESSARY)

PIN 5: WH-F189 (WHT/ORN)

PIN 2: WH-RV12-OAT (YEL) PIN 1: WH-F188 (WHT)

F-1207B BAGGAGE BULKHEAD EDC-10A 9 PIN FEMALE D-SUB CONNECTOR NOTE: SNIP OFF ANY CABLE SHIELD COMING FROM THE END OF THE OAT HARNESS.

WH-P30

PIN 9: WH-F191 (WHT/GRN) PIN 8: WH-RV12-OAT (BLU) PIN 7: WH-RV12-OAT (RED) PIN 6: WH-F190 (WHT/BLU)

FIGURE 2: INSTALLING PINS IN THE EDC-10A D-SUB CONNECTOR (REAR VIEW / WIRE INSERTION SIDE)
F-1207C-L F-1207D-L STATIC LINE F-1206A

FIGURE 1: BAGGAGE AND TAILCONE WIRE ROUTINGS


PAGE

31-12

RV-12

REVISION:

DATE:

09/15/09

You might also like