Scribd
Upload
31 views1 page

Van'S Aircraft, Inc.: Figure 1: Routing Line Through Ribs Figure 3: Terminal Bracket Installation

The document provides instructions for installing terminal brackets and routing wiring on an aircraft. It involves 7 steps: 1) Cut string and route through nose ribs on each wing; 2) Attach a connector to the end of the WH-B218 wire; 3) Make two WH-B216 ground wires; 4) Attach the WH-B218 and one WH-B216 wire to the left terminal bracket; 5) Attach the other WH-B216 wire to the right terminal bracket; 6) Install the terminal brackets without pinching wires; 7) Route ground wires around the brackets and fasten with screws. Diagrams are provided to illustrate the instructions.

Uploaded by

Mark Evan Salutin
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
31 views1 page

Van'S Aircraft, Inc.: Figure 1: Routing Line Through Ribs Figure 3: Terminal Bracket Installation

The document provides instructions for installing terminal brackets and routing wiring on an aircraft. It involves 7 steps: 1) Cut string and route through nose ribs on each wing; 2) Attach a connector to the end of the WH-B218 wire; 3) Make two WH-B216 ground wires; 4) Attach the WH-B218 and one WH-B216 wire to the left terminal bracket; 5) Attach the other WH-B216 wire to the right terminal bracket; 6) Install the terminal brackets without pinching wires; 7) Route ground wires around the brackets and fasten with screws. Diagrams are provided to illustrate the instructions.

Uploaded by

Mark Evan Salutin
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

VAN'S AIRCRAFT, INC.

Step 7: Install the W-1205-L and W-1205-R Terminal Brackets as shown in Figure 3. Take care not to pinch wires between the attachment points. Route the WH-B216 (WHT) Terminal Ground Wires around the forward flange of the terminal brackets and fasten the connector with the terminal bracket mounting screw. Other wires should be neatly tucked behind terminal bracket. Step 1: Cut two 12 foot lengths of string or fishing line (not supplied in kit). Step 2: Starting from the most outboard W-1208 Nose Rib, route a length of string or fishing line inboard through the snap bushing in all of the nose ribs. Tape the ends of the string or fishing line on the most outboard and most inboard nose rib. Repeat process on the right wing. See Figure 1. W-1208-R W-SPAR ASSY-L

W-1208BC-L

WH-B218 (WHT) TAPE END TO INBOARD NOSE RIB WH-B216 (WHT)

STRING OR FISHING LINE

AN515-8R8, 3 PLACES

W-1208-R

TAPE END TO OUTBOARD NOSE RIB

W-1205-L

FIGURE 1: ROUTING LINE THROUGH RIBS FIGURE 3: TERMINAL BRACKET INSTALLATION


Step 3: Take the inboard end of the WH-B218 (WHT) Terminal Wire and attach a connector as shown in Figure 2. Ensure that the connector is properly installed. Step 4: Make two WH-B216 (WHT) Terminal Ground Wires by cutting #18 wire to 5" lengths and attaching a connector to each end as shown in Figure 2. Step 5: Attach the WH-B218 (WHT) Terminal Wire and one of the WH-B216 (WHT) Terminal Ground Wires to the W-1205-L Terminal Bracket as shown in Figure 2. Step 6: Attach the second WH-B216 (WHT)Terminal Ground Wire to the W-1205-R Terminal Bracket as shown in Figure 2. WH-B216 (WHT) WH-B218 (WHT)
ES 31890, 3 PLACES

AN515-8R8, 2 PLACES

MS21042-08, 2 PLACES

W-1205-L

FIGURE 2: ATTACHING WIRES TO TERMINAL BRACKET


PAGE

16-04

RV-12

REVISION:

DATE:

09/15/09

You might also like