Overhead Transmission Standards

230kV INSULATOR PLATE INDEX

A-FRAME AND LATTICE STRUCTURES FOR SUBSTATIONS
1. 2. 3. IASDFC3: SINGLE DEAD-END, FULL TENSION, 3-PHASE IASDSC3: SINGLE DEAD-END, SLACK TENSION, 3-PHASE IELDFC1: INSULATOR EXTENSION, DOUBLE INSULATOR FULL TENSION PAGE CIN-2 CIN-3 CIN-4

SPUN CONCRETE POLES

4. 5. 6. 7. 8. 9. IESSFC1 & IESSSC1: INSULATOR EXTENSION, DOUBLE INSULATOR ISDBC3: DOUBLE BRACED LINE POST, 3-PHASE ISDD3FSC3: DOUBLE DEAD-END 135, FULL TENSION TO SLACK TENSION, 3-PHASE ISDD8FFC3: DOUBLE DEAD-END 180, FULL TENSION TO FULL TENSION, 3-PHASE ISDD9FFC1: DOUBLE DEAD-END 90, FULL TENSION TO FULL TENSION, 1-PHASE ISDD9FFC3: DOUBLE DEAD-END 90, FULL TENSION TO FULL TENSION, 3-PHASE CIN-5 CIN-6 CIN-8 CIN-10 CIN-12 CIN-14 CIN-16 CIN-18 CIN-20 CIN-22 CIN-24 CIN-26 CIN-28 CIN-31 CIN-32 CIN-34 CIN-36 CIN-38 CIN-40

10. ISDD9FSC1: DOUBLE DEAD-END 90, FULL TENSION TO SLACK TENSION, 1-PHASE 11. ISDD9FSC3: DOUBLE DEAD-END 90, FULL TENSION TO SLACK TENSION, 3-PHASE 12. ISDD9SSC2: DOUBLE DEAD-END 90, SLACK TENSION TO SLACK TENSION, 3-PHASE 13. ISSBBGC3: SINGLE BRACED LINE POST, BOTTOM GUY, 3-PHASE 14. ISSBDC3: SINGLE BRACED LINE POST, DELTA CONFIGURATION, 3-PHASE 15. ISSBNGC3: SINGLE BRACED LINE POST, NO GUY, 3-PHASE 16. ISSBTGC3: SINGLE BRACED LINE POST, TOP GUY, 3-PHASE 17. ISSDFC3: SINGLE DEAD-END, FULL TENSION, 3-PHASE 18. ISSDFP2C3: SINGLE DEAD-END, FULL TENSION TO POST, TYPE 2, 3-PHASE 19. ISSDFP3C3: SINGLE DEADE-END, FULL TENSION TO POST, TYPE 3, 3-PHASE 20. ISSDSC3: SINGLE DEAD-END, SLACK TENSION, 3-PHASE 21. ISSSDGGC3: SINGLE SUSPENSION, DOUBLE GRIP, GUYED, 3-PHASE 22. ISSSDGNC3: SINGLE SUSPENSION, DOUBLE GRIP, NO GUY, 3-PHASE

REVISED/REVIEWED: OCTOBER 2012

REVISED/REVIEWED BY: MLR

APPROVED BY: RHS

230kV INSULATORS
CIN-1

Overhead Transmission Standards

IASDFC3
INSULATOR FOR SUBSTATION A-FRAME/LATTICE STRUCTURES SINGLE DEAD-END, FULL TENSION, 230KV, 3-PHASE
CONDUCTOR OPTIONS: 954S, 1590

IASDFC3 BASE NO. ITEM ID

1 26 50 ADCVF 001 CLEHL 005 INSDE 002

QTY
3 3 3

DESCRIPTION
VOID FILLER COMPOUND FOR DEADEND ASSEMBLY SOCKET-Y CLEVIS, CLASS 52-8/11, L = 11", PIN=7/8", H.D.G.. DEADEND SILICON INSULATOR, Y-BALL COUPLING, 230KV, L = 111", CLASS 52-8/11

IASDFC3*954S NO. ITEM ID

42 DEACB 005

QTY
3

DESCRIPTION
DEADEND COMPRESSION ASSEMBLY FOR 954 ACSR, OVAL EYE

IASDFC3*1590 NO. ITEM ID

42 DEACB 007

QTY
3

DESCRIPTION
DEADEND COMPRESSION ASSEMBLY FOR 1590 ACSR, OVAL EYE

REVISED/REVIEWED: OCTOBER 2012

REVISED/REVIEWED BY: MLR

APPROVED BY: RHS

230kV INSULATORS
CIN-2

Overhead Transmission Standards

IASDSC3
INSULATOR FOR SUBSTATION A-FRAME/LATTICE STRUCTURES SINGLE DEAD-END, SLACK TENSION, 230KV, 3-PHASE
CONDUCTOR OPTIONS: 556S, 954A, 954S, 1590

IASDSC3 BASE NO. ITEM ID

12 26 50 59 76 BOLMS 016 CLEHL 008 INSDE 002 NUTEY 002 WASRD 004

QTY
3 3 3 3 6

DESCRIPTION
MACHINE BOLT, 5/8" X 3", SQUARE HEAD, GALVANIZED, W/SQUARE NUT ATTACHED SOCKET-EYE CLEVIS, CLASS 52-8/11, L = 10", EYE = 3/4" THICK W/ 13/16" OPENING, H. D. G. DEADEND SILICON INSULATOR, Y-BALL COUPLING, 230KV, L = 111", CLASS 52-8/11 EYE NUT FOR 5/8" BOLT, 1 1/2" OPENING, H.D.G. ROUND WASHER FOR 5/8" BOLT, 1 3/4" DIAMETER, GALVANIZED

IASDSC3*556S, 954A, 954S NO. ITEM ID QTY

21 CLAQD 005 3

DESCRIPTION
DEADEND CLAMP (.7 1.39") 35,000# STRENGTH, GAP = 1 7/16", PIN = 3/4"

IASDSC3*1590 NO. ITEM ID

21 CLAQD 006

QTY
3

DESCRIPTION
DEADEND CLAMP (1.18 - 1.52") 35,000# STRENGTH, GAP = 2", PIN = 3/4"

REVISED/REVIEWED: OCTOBER 2012

REVISED/REVIEWED BY: MLR

APPROVED BY: RHS

230kV INSULATORS
CIN-3

Overhead Transmission Standards

IELDFC1
INSULATOR EXTENSION FOR LATTICE TOWERS DOUBLE INSULATOR, FULL TENSION, 230KV, 1-PHASE
CONDUCTOR OPTIONS: 954S, 1590

IELDFC1 BASE NO. ITEM ID

1 27 50 67 80 85 ADCVF 001 CLESO 005 INSDE 002 SHAAN 004 YOKPL 005 HDWTU 001

QTY
1 2 2 2 2 1

DESCRIPTION
VOID FILLER COMPOUND FOR DEADEND ASSEMBLIES, 1 LB TUBE CLEVIS, SOCKET - Y, 50,000 LB, CLASS 52-8/11. INSULATOR, DEADEND, SILICON, Y-BALL COUPLING, ANSI 52-8/11, 50,000#, L=111", 230KV NC SHACKLE, ANCHOR, 3/4", 60,000#, GALV. YOKE PLATE, SUSPENSION, TRIANGLULAR STRA IN, 18" INSULATOR SPACING, 60000#, GALVA NIZED, 15/16" HOLE DIA TURNBUCKLE, CLEVIS-EYE, 12" TAKEUP, 76,000#

IELDFC1*954S
42 DEACB 005 1 DEADEND COMPRESSION ASSEMBLY FOR 954 ACSR, OVAL EYE, ACSR ONLY

IELDFC1*1590
42 DEACB 007 1 DEADEND COMPRESSION ASSEMBLY FOR 1590 ACSR, OVAL EYE, ACSR ONLY

REVISED/REVIEWED: OCTOBER 2012

REVISED/REVIEWED BY: MLR

APPROVED BY: RHS

230kV INSULATORS
CIN-4

Overhead Transmission Standards

IESSFC1 & IESSSC1

INSULATOR EXTENSION FOR SPUN CONCRETE POLES SINGLE INSULATOR, FULL/SLACK TENSION, 230KV, 1-PHASE
CONDUCTOR OPTIONS: 954S, 1590

IESSFC1 BASE NO. ITEM ID

1 27 50 85 42 42 ADCVF 001 CLESO 005 INSDE 002 HDWTU 001 DEACB 005 DEACB 007

QTY
1 1 1 1 1 1

DESCRIPTION
VOID FILLER COMPOUND FOR DEADEND ASSEMBLIES, 1 LB TUBE CLEVIS, SOCKET - Y, 50,000 LB, CLASS 52-8/11. INSULATOR, DEADEND, SILICON, Y-BALL COUPLING, ANSI 52-8/11, 50,000#, L=111", 230KV NC TURNBUCKLE, CLEVIS-EYE, 12" TAKEUP, 76,000# DEADEND COMPRESSION ASSEMBLY FOR 954 ACSR, OVAL EYE, ACSR ONLY DEADEND COMPRESSION ASSEMBLY FOR 1590 ACSR, OVAL EYE, ACSR ONLY

IESSFC1*954S IESSFC1*1590 IESSSC1 BASE NO. ITEM ID

26 50 85 27 27 CLEHL 008 INSDE 002 HDWTU 001 CLAQD 005 CLAQD 006

QTY
1 1 1 1 1

DESCRIPTION
SOCKET-EYE CLEVIS, CLASS 52-8/11, L = 10, EYE = 3/4 THICK W/ 13/16 OPENING, H.D.G. INSULATOR, DEADEND, SILICON, Y-BALL COUPLING, ANSI 52-8/11, 50,000#, L=111", 230KV NC TURNBUCKLE, CLEVIS-EYE, 12" TAKEUP, 76,000# DEADEND CLAMP (.7 - 1.39" = 336-1272 ACSR, 397-1431 AAC) 35,000# STRENGTH, GAP = 1 7/16", PIN = 3/4" DEADEND CLAMP (1.18 - 1.52" = 1033-1510 ACSR, 1100-1700 AAC) 35,000# STRENGTH, GAP = 2", PIN = 3/4"

IESSSC1*954S IESSSC1*1590

REVISED/REVIEWED: OCTOBER 2012

REVISED/REVIEWED BY: MLR

APPROVED BY: RHS

230kV INSULATORS
CIN-5

Overhead Transmission Standards

ISDBC3
INSULATOR FOR SPUN CONCRETE POLES DOUBLE BRACED LINE POST, 230KV, 3-PHASE
CONDUCTOR OPTIONS: 954A, 954S, 1590

SEE MBA1 FOR BOLT ASSEMBLY DETAILS MBA2 FOR DOUBLE ARMING BOLT ASSEMBLY DETAILS MINIMUM REQUIRED BOLT LENGTHS (INCHES) STRUCTURE TOP MIDDLE BOTTOM A 21.1 23.2 25.4 B 20.9 23.1 25.2 C 34.5 36.7 38.8 D 35.0 37.2 39.3

NOTE:

BOLT CALCULATIONS ASSUME A 17" POLE TOP DIAMETER

REVISED/REVIEWED: OCTOBER 2012

REVISED/REVIEWED BY: MLR

APPROVED BY: RHS

230kV INSULATORS
CIN-6

Overhead Transmission Standards

ISDBC3 PLATES
ISDBC3 BASE NO. ITEM ID
10 11 11 11 12 12 12 24 26 36 53 58 62 69 76 77 BKTLP 002 BOLDA 039 BOLDA 040 BOLDA 043 BOLMS 052 BOLMS 053 BOLMS 054 CLATG 001 CLEHL 001 COBCO 028 INSLP 014 LUGGR 002 NUTSL 005 SOCEY 003 WASRD 006 WASSC 002

QTY
6 2 2 2 2 2 2 3 6 9 FT 6 6 18 6 36 12

DESCRIPTION
BRACKET, 53 ANGLE, 6" HOLE SPACING, 1 1/16" HOLE DIAMETER, 5/8" THICK DOUBLE ARMING BOLT, 7/8" X 36", WITH 4 SQUARE NUTS ATTACHED DOUBLE ARMING BOLT, 7/8" X 38", WITH 4 SQUARE NUTS ATTACHED DOUBLE ARMING BOLT, 7/8" X 40", WITH 4 SQUARE NUTS ATTACHED MACHINE BOLT, 7/8" X 22", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 24", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 26", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED CLAMP, TRANSFORMER TANK GROUND, BRONZE, #6 SOL - #1 STR BALL-Y CLEVIS, CLASS 52-3/5, STRENGTH = 30,000#, L > 9", PIN = 3/4", H.D.G. #4 SOLID BARE COPPER CONDUCTOR, SOFT DRAWN 230KV SILICONE BRACED LINE POST INSULATOR, 17 RISE, GAIN BASE, L = 108", H = 94", 14" B.H.S. LUG FOR 7/8" BOLT, #4 SOLID WIRE, TIN PLATTED COPPER COMPRESSION SQUARE LOCK NUT FOR 7/8" BOLT, H.D.G. SOCKET - EYE, STENGTH = 25,000#, L = 2 5/16", EYE = 13/16", FORGED STEEL, GALV. ROUND WASHER FOR 7/8" BOLT, 2 1/2" DIAMETER, GALVANIZED SQUARE CURVED WASHER FOR 7/8" BOLTS, GALVANIZED, 4" X 4"

ISDBC3*954A
45 GRISA 003 6 ARMOR GRIP SUSPENSION ASSEMBLY FOR 954 AAC, 82", 1 3/16" GAP, 5/8" PIN

ISDBC3*954S
45 GRISA 004 6 ARMOR GRIP SUSPENSION ASSEMBLY FOR 954 ACSR, 82", 1 3/16" GAP, 5/8" PIN

ISDBC3*1590
45 GRISA 005 6 ARMOR GRIP SUSPENSION ASSEMBLY FOR 1590 ACSR, 88", 1 3/8" GAP, 3/4" PIN

REVISED/REVIEWED: OCTOBER 2012

REVISED/REVIEWED BY: MLR

APPROVED BY: RHS

230kV INSULATORS
CIN-7

Overhead Transmission Standards

ISDD3FSC3
INSULATOR FOR SPUN CONCRETE POLES DOUBLE DEADEND 135, FULL TENSION TO SLACK TENSION, 230KV, 3-PHASE
CONDUCTOR OPTIONS: 954S, 1590

NOTE: SEE MBA1 FOR BOLT ASSEMBLY DETAILS TOP BOLT A LENGTH (INCHES) BOLT B LENGTH (INCHES) EYEBOLT C LENGTH (INCHES) BOLT D LENGTH (INCHES) BOLT E LENGTH (INCHES) 25.4 23.8 22.7 28.5 29.1 MIDDLE 27.8 26.1 25.1 30.9 31.4 BOTTOM 30.1 28.5 27.4 33.3 33.8

NOTE: BOLT CALCULATIONS ASSUME A 17" POLE TOP DIAMETER

REVISED/REVIEWED: OCTOBER 2012

REVISED/REVIEWED BY: MLR

APPROVED BY: RHS

230kV INSULATORS
CIN-8

Overhead Transmission Standards

ISDD3FSC3 PLATES
ISDD3FSC3 BASE NO. ITEM ID
1 7 12 12 12 13 13 13 24 26 26 31 36 50 51 58 62 69 72 76 77 ADCVF 001 BALFI 007 BOLMS 073 BOLMS 074 BOLMS 075 BOLSE 022 BOLSE 023 BOLSE 024 CLATG 001 CLEHL 005 CLEHL 008 CNNCP 016 COBCO 028 INSDE 002 INSHP 025 LUGGR 002 NUTSL 005 SOCEY 003 TEEDE 003 WASRD 006 WASSC 002

QTY
3 3 2 2 2 1 1 1 3 3 3 3 21 ft 6 3 6 9 3 6 15 12

DESCRIPTION
VOID FILLER COMPOUND FOR DEADEND ASSEMBLY BALL Y-CLEVIS, CLASS 52-3/5 MACHINE BOLT, 7/8" X 30", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 32", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 36", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED BOLT, SHOULDER EYE, 7/8" X 24", GALVANIZED, WITH SQUARE NUT ATTACHED BOLT, SHOULDER EYE, 7/8" X 26", GALVANIZED, WITH SQUARE NUT ATTACHED BOLT, SHOULDER EYE, 7/8" X 28", GALVANIZED, WITH SQUARE NUT ATTACHED CLAMP, TRANSFORMER TANK GROUND, BRONZE, #6 SOL - #1 STR SOCKET-Y CLEVIS, CLASS 52-8/11, L = 11", PIN = 7/8", H.D.G. SOCKET-EYE CLEVIS, CLASS 52-8/11, L = 10", EYE = 3/4" THICK W/ 13/16" OPENING, H. D. G. COMPRESSION CONNECTOR, #4 SOL. CU. TO #4 SOL. CU., COPPER #4 SOLID BARE COPPER CONDUCTOR, SOFT DRAWN DEADEND SILICON INSULATOR, Y-BALL COUPLING, 230KV, L = 111", CLASS 52-8/11 HORIZONTAL POST SILICONE INSULATOR, 230KV, L = 86", GAIN BASE, 17 RISE LUG FOR 7/8" BOLT, #4 SOLID WIRE, TIN PLATTED COPPER COMPRESSION SQUARE LOCK NUT FOR 7/8" BOLT, H.D.G. SOCKET EYE, CLASS 52-3/5 TEE, DUCTILE IRON, HOT-DIP GALVANIZED, 6" HOLE SPACING, STRENGTH = 60,000# ROUND WASHER FOR 7/8" BOLT, 2 1/2" DIAMETER, GALVANIZED SQUARE FLAT WASHER FOR 3/4" & 7/8" BOLT, 4" SQ X 1/4", GALVANIZED

ISDD3FSC3*954S NO. ITEM ID

12 12 12 12 12 20 21 42 58 62 76 BOLMS 053 BOLMS 054 BOLMS 055 BOLMS 073 BOLMS 074 CLAJU 007 CLAQD 005 DEACB 005 LUGGR 002 NUTSL 005 WASRD 006

QTY
1 1 2 1 1 3 3 3 3 6 12

DESCRIPTION
MACHINE BOLT, 7/8" X 24", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 26", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 28", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 30", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 32", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED CUSHION GRIP SUSPENSION CLAMP FOR 954 ACSR DEADEND CLAMP (.7 1.39") 35,000# STRENGTH, GAP = 1 7/16", PIN = 3/4" DEADEND COMPRESSION ASSEMBLY FOR 954 ACSR, OVAL EYE LUG FOR 7/8" BOLT, #4 SOLID WIRE, TIN PLATED COPPER COMPRESSION SQUARE LOCK NUT FOR 7/8" BOLT, H.D.G. ROUND WASHER FOR 7/8" BOLT, 2 1/2" DIAMETER, GALVANIZED

ISDD3FSC3*1590 NO. ITEM ID

12 12 12 12 12 20 21 42 58 62 76 BOLMS 063 BOLMS 064 BOLMS 070 BOLMS 071 BOLMS 072 CLAJU 008 CLAQD 006 DEACB 007 LUGGR 003 NUTSL 006 WASRD 007
7

QTY
1 1 2 1 1 3 3 3 3 6 12

DESCRIPTION
MACHINE BOLT, 1" X 24", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 1" X 26", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 1" X 28", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 1" X 30", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 1" X 32", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED CUSHION GRIP SUSPENSION CLAMP FOR 1590 ACSR DEADEND CLAMP (1.18 - 1.52") 35,000# STRENGTH, GAP = 2", PIN = 3/4" DEADEND COMPRESSION ASSEMBLY FOR 1590 ACSR, OVAL EYE LUG FOR 1" BOLT, #4 SOLID WIRE, TIN PLATED COPPER COMPRESSION SQUARE LOCK NUT FOR 1" BOLT, H.D.G. ROUND WASHER FOR 1" BOLT, 2 1/2" DIAMETER, GALVANIZED

Note: use /8" bolts for Post Insulator and Slack Tension Insulator.

REVISED/REVIEWED: OCTOBER 2012

REVISED/REVIEWED BY: MLR

APPROVED BY: RHS

230kV INSULATORS
CIN-9

Overhead Transmission Standards

ISDD8FFC3
INSULATOR FOR SPUN CONCRETE POLES DOUBLE DEAD-END 180, FULL TENSION TO FULL TENSION, 230KV, 3-PHASE
CONDUCTOR OPTIONS: 954S, 1590

NOTE: SEE MBA1 FOR BOLT ASSEMBLY DETAILS DEADEND INSULATOR UPPER BOLT A LENGTH (INCHES) LOWER BOLT B LENGTH (INCHES) TOP 25.4 23.8 MIDDLE 27.8 26.1 BOTTOM 30.1 28.5

POST INSULATOR UPPER BOLT C LENGTH (INCHES) LOWER BOLT D LENGTH (INCHES) NOTE:

TOP 28.5 29.0

MIDDLE 30.8 31.3

BOTTOM 33.2 33.7

BOLT CALCULATIONS ASSUME A 17" POLE TOP DIAMETER

REVISED/REVIEWED: OCTOBER 2012

REVISED/REVIEWED BY: MLR

APPROVED BY: RHS

230kV INSULATORS
CIN-10

Overhead Transmission Standards

ISDD8FFC3 PLATES
ISDD8FFC3 BASE NO. ITEM ID
1 7 12 12 12 24 26 36 50 51 58 62 69 72 76 77 ADCVF 001 BALFI 007 BOLMS 073 BOLMS 074 BOLMS 075 CLATG 001 CLEHL 005 COBCO 028 INSDE 002 INSHP 025 LUGGR 002 NUTSL 005 SOCEY 003 TEEDE 003 WASRD 006 WASSC 002

QTY
6 3 2 2 2 3 6 12 ft 6 3 3 6 3 6 12 6

DESCRIPTION
VOID FILLER COMPOUND FOR DEADEND ASSEMBLY BALL Y-CLEVIS, CLASS 52-3/5 MACHINE BOLT, 7/8" X 30", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 32", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 36", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED CLAMP, TRANSFORMER TANK GROUND, BRONZE, #6 SOL - #1 STR SOCKET-Y CLEVIS, CLASS 52-8/11, L = 11", PIN = 7/8", H.D.G. #4 SOLID BARE COPPER CONDUCTOR, SOFT DRAWN DEADEND SILICON INSULATOR, Y-BALL COUPLING, 230KV, L = 111", CLASS 52-8/11 HORIZONTAL POST INSULATOR, 230KV, L = 86", GAIN BASE, 17 RISE LUG FOR 7/8" BOLT, #4 SOLID WIRE, TIN PLATTED COPPER COMPRESSION SQUARE LOCK NUT FOR 7/8" BOLT, H.D.G. SOCKET EYE, CLASS 52-3/5 TEE, DUCTILE IRON, HOT-DIP GALVANIZED, 6" HOLE SPACING, STRENGTH = 60,000# ROUND WASHER FOR 7/8" BOLT, 2 " DIAMETER, GALVANIZED SQUARE CURVED WASHER FOR 7/8" BOLTS, GALVANIZED, 4" X 4" SIZE

ISDD8FFC3*954S NO. ITEM ID

12 12 12 12 12 20 42 58 62 76 BOLMS 053 BOLMS 054 BOLMS 055 BOLMS 073 BOLMS 074 CLAJU 007 DEACB 005 LUGGR 002 NUTSL 005 WASRD 006

QTY
1 1 2 1 1 3 6 3 6 12

DESCRIPTION
MACHINE BOLT, 7/8" X 24", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 26", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 28", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 30", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 32", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED CUSHION GRIP SUSPENSION CLAMP FOR 954 ACSR DEADEND COMPRESSION ASSEMBLY FOR 954 ACSR, OVAL EYE LUG FOR 7/8" BOLT, #4 SOLID WIRE, TIN PLATED COPPER COMPRESSION SQUARE LOCK NUT FOR 7/8" BOLT, H.D.G. ROUND WASHER FOR 7/8" BOLT, 2 1/2" DIAMETER, GALVANIZED

ISDD8FFC3*1590 NO. ITEM ID

12 12 12 12 12 20 42 58 62 76 BOLMS 063 BOLMS 064 BOLMS 070 BOLMS 071 BOLMS 072 CLAJU 008 DEACB 007 LUGGR 003 NUTSL 006 WASRD 007

QTY
1 1 2 1 1 3 6 3 6 12

DESCRIPTION
MACHINE BOLT, 1" X 24", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 1" X 26", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 1" X 28", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 1" X 30", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 1" X 32", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED CUSHION GRIP SUSPENSION CLAMP FOR 1590 ACSR DEADEND COMPRESSION ASSEMBLY FOR 1590 ACSR, OVAL EYE LUG FOR 1" BOLT, #4 SOLID WIRE, TIN PLATED COPPER COMPRESSION SQUARE LOCK NUT FOR 1" BOLT, H.D.G. ROUND WASHER FOR 1" BOLT, 2 1/2" DIAMETER, GALVANIZED

REVISED/REVIEWED: OCTOBER 2012

REVISED/REVIEWED BY: MLR

APPROVED BY: RHS

230kV INSULATORS
CIN-11

Overhead Transmission Standards

ISDD9FFC1
INSULATOR FOR SPUN CONCRETE POLES DOUBLE DEAD-END 90, FULL TENSION TO FULL TENSION, 230KV, 1-PHASE
CONDUCTOR OPTIONS: 954S, 1590

NOTE: SEE MBA1 FOR BOLT ASSEMBLY DETAILS

A UPPER TEE MINIMUM BOLT LENGTH (INCHES) LOWER TEE MINIMUM BOLT LENGTH (INCHES) 22.9 22.9

B 21.2 21.3

NOTE: BOLT CALCULATIONS ASSUME A 17" POLE TOP DIAMETER.

REVISED/REVIEWED: OCTOBER 2012

REVISED/REVIEWED BY: MLR

APPROVED BY: RHS

230kV INSULATORS
CIN-12

Overhead Transmission Standards

ISDD9FFC1 PLATES
ISDD9FFC1 BASE NO. ITEM ID
1 24 26 31 36 50 72 ADCVF 001 CLATG 001 CLEHL 005 CNNCP 016 COBCO 028 INSDE 002 TEEDE 003

QTY
2 1 2 2 6 ft 2 4

DESCRIPTION
VOID FILLER COMPOUND FOR DEADEND ASSEMBLY CLAMP, TRANSFORMER TANK GROUND, BRONZE, #6 SOL - #1 STR SOCKET-Y CLEVIS, CLASS 52-8/11, L = 11", PIN = 7/8", H.D.G. COMPRESSION CONNECTOR, #4 SOL. CU. TO #4 SOL. CU., COPPER #4 SOLID BARE COPPER CONDUCTOR, SOFT DRAWN DEADEND SILICON INSULATOR, Y-BALL COUPLING, 230KV, L = 111", CLASS 52-8/11 TEE, DUCTILE IRON, HOT-DIP GALVANIZED, 6" HOLE SPACING, STRENGTH = 60,000#

ISDD9FFC1*954S NO. ITEM ID

12 12 42 58 62 76 BOLMS 052 BOLMS 053 DEACB 005 LUGGR 002 NUTSL 005 WASRD 006

QTY
2 2 2 2 4 8

DESCRIPTION
MACHINE BOLT, 7/8" X 22", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 24", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED DEADEND COMPRESSION ASSEMBLY FOR 954 ACSR, OVAL EYE LUG FOR 7/8" BOLT, #4 SOLID WIRE, TIN PLATED COPPER COMPRESSION SQUARE LOCK NUT FOR 7/8" BOLT, H.D.G. ROUND WASHER FOR 7/8" BOLT, 2 1/2" DIAMETER, GALVANIZED

ISDD9FFC1*1590 NO. ITEM ID

12 12 42 58 62 76 BOLMS 062 BOLMS 063 DEACB 007 LUGGR 003 NUTSL 006 WASRD 007

QTY
2 2 2 2 4 8

DESCRIPTION
MACHINE BOLT, 1" X 22", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 1" X 24", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED DEADEND COMPRESSION ASSEMBLY FOR 1590 ACSR, OVAL EYE LUG FOR 1" BOLT, #4 SOLID WIRE, TIN PLATED COPPER COMPRESSION SQUARE LOCK NUT FOR 1" BOLT, H.D.G. ROUND WASHER FOR 1" BOLT, 2 1/2" DIAMETER, GALVANIZED

REVISED/REVIEWED: OCTOBER 2012

REVISED/REVIEWED BY: MLR

APPROVED BY: RHS

230kV INSULATORS
CIN-13

Overhead Transmission Standards

ISDD9FFC3
INSULATOR FOR SPUN CONCRETE POLES DOUBLE DEAD-END 90, FULL TENSION TO FULL TENSION, 230KV, 3-PHASE
CONDUCTOR OPTIONS: 954S, 1590

NOTE: SEE MBA1 FOR BOLT ASSEMBLY DETAILS

UPPER TEE SUBSTRUCTURE UPPER BOLT A LENGTH (INCHES) LOWER BOLT B LENGTH (INCHES) Top 25.4 23.8 Mid 27.8 26.1 Bottom 30.1 28.5 Top 25.4 23.8

LOWER TEE Mid 27.8 26.2 Bottom 30.2 28.6

NOTE: BOLT CALCULATIONS ASSUME A 17" POLE TOP DIAMETER

REVISED/REVIEWED: OCTOBER 2012

REVISED/REVIEWED BY: MLR

APPROVED BY: RHS

230kV INSULATORS
CIN-14

Overhead Transmission Standards

ISDD9FFC3 PLATES
ISDD9FFC3 BASE NO. ITEM ID
1 24 26 31 36 50 72 ADCVF 001 CLATG 001 CLEHL 005 CNNCP 016 COBCO 028 INSDE 002 TEEDE 003

QTY
6 3 6 6 18 ft 6 12

DESCRIPTION
VOID FILLER COMPOUND FOR DEADEND ASSEMBLY CLAMP, TRANSFORMER TANK GROUND, BRONZE, #6 SOL - #1 STR SOCKET-Y CLEVIS, CLASS 52-8/11, L = 11", PIN = 7/8", H.D.G. COMPRESSION CONNECTOR, #4 SOL. CU. TO #4 SOL. CU., COPPER #4 SOLID BARE COPPER CONDUCTOR, SOFT DRAWN DEADEND SILICON INSULATOR, Y-BALL COUPLING, 230KV, L = 111", CLASS 52-8/11 TEE, DUCTILE IRON, HOT-DIP GALVANIZED, 6" HOLE SPACING, STRENGTH = 60,000#

ISDD9FFC3*954S NO. ITEM ID

12 12 12 12 12 42 58 62 76 BOLMS 053 BOLMS 054 BOLMS 055 BOLMS 073 BOLMS 074 DEACB 005 LUGGR 002 NUTSL 005 WASRD 006

QTY
2 2 4 2 2 6 6 12 24

DESCRIPTION
MACHINE BOLT, 7/8" X 24", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 26", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 28", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 30", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 32", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED DEADEND COMPRESSION ASSEMBLY FOR 954 ACSR, OVAL EYE LUG FOR 7/8" BOLT, #4 SOLID WIRE, TIN PLATED COPPER COMPRESSION SQUARE LOCK NUT FOR 7/8" BOLT, H.D.G. ROUND WASHER FOR 7/8" BOLT, 2 1/2" DIAMETER, GALVANIZED

ISDD9FFC3*1590 NO. ITEM ID

12 12 12 12 12 42 58 62 76 BOLMS 063 BOLMS 064 BOLMS 070 BOLMS 071 BOLMS 072 DEACB 007 LUGGR 003 NUTSL 006 WASRD 007

QTY
2 2 4 2 2 6 6 12 24

DESCRIPTION
MACHINE BOLT, 1" X 24", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 1" X 26", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 1" X 28", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 1" X 30", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 1" X 32", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED DEADEND COMPRESSION ASSEMBLY FOR 1590 ACSR, OVAL EYE LUG FOR 1" BOLT, #4 SOLID WIRE, TIN PLATED COPPER COMPRESSION SQUARE LOCK NUT FOR 1" BOLT, H.D.G. ROUND WASHER FOR 1" BOLT, 2 1/2" DIAMETER, GALVANIZED

REVISED/REVIEWED: OCTOBER 2012

REVISED/REVIEWED BY: MLR

APPROVED BY: RHS

230kV INSULATORS
CIN-15

Overhead Transmission Standards

ISDD9FSC1
INSULATOR FOR SPUN CONCRETE POLES DOUBLE DEAD-END 90, FULL TENSION TO SLACK TENSION, 230KV, 1-PHASE
CONDUCTOR OPTIONS: 954S, 1590

NOTE: SEE MBA1 FOR BOLT ASSEMBLY DETAILS FULL TENSION SIDES SUBSTRUCTURE UPPER BOLT A LENGTH (INCHES) LOWER BOLT B LENGTH (INCHES)

Top 22.9 21.2

SLACK TENSION SIDES SUBSTRUCTURE UPPER BOLT A LENGTH (INCHES) LOWER BOLT B LENGTH (INCHES)

Top 21.5 20.8

NOTE: BOLT CALCULATIONS ASSUME A 17" POLE TOP DIAMETER

REVISED/REVIEWED: OCTOBER 2012

REVISED/REVIEWED BY: MLR

APPROVED BY: RHS

230kV INSULATORS
CIN-16

Overhead Transmission Standards

ISDD9FSC1 PLATES
ISDD9FSC1 BASE NO. ITEM ID
1 12 24 26 26 31 36 50 58 62 72 76 77 ADCVF 001 BOLMS 052 CLATG 001 CLEHL 005 CLEHL 008 CNNCP 016 COBCO 028 INSDE 002 LUGGR 002 NUTSL 005 TEEDE 003 WASRD 006 WASSC 002

QTY
1 2 1 1 1 1 6 ft 2 1 2 3 4 2

DESCRIPTION
VOID FILLER COMPOUND FOR DEADEND ASSEMBLY MACHINE BOLT, 7/8" X 22", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED CLAMP, TRANSFORMER TANK GROUND, BRONZE, #6 SOL - #1 STR SOCKET-Y CLEVIS, CLASS 52-8/11, L = 11", PIN = 7/8", H.D.G. SOCKET-EYE CLEVIS, CLASS 52-8/11, L = 10", EYE = 3/4" THICK W/ 13/16" OPENING, H. D. G. COMPRESSION CONNECTOR, #4 SOL. CU. TO #4 SOL. CU., COPPER #4 SOLID BARE COPPER CONDUCTOR, SOFT DRAWN DEADEND SILICON INSULATOR, Y-BALL COUPLING, 230KV, L = 111", CLASS 52-8/11 LUG FOR 7/8" BOLT, #4 SOLID WIRE, TIN PLATED COPPER COMPRESSION SQUARE LOCK NUT FOR 7/8" BOLT, H.D.G. TEE, DUCTILE IRON, HOT-DIP GALVANIZED, 6" HOLE SPACING, STRENGTH = 60,000# ROUND WASHER FOR 7/8" BOLT, 2 1/2" DIAMETER, GALVANIZED SQUARE CURVED WASHER FOR 7/8" BOLTS, GALVANIZED, 4" X 4"

ISDD9FSC1*954S NO. ITEM ID

12 12 21 42 58 62 76 BOLMS 052 BOLMS 053 CLAQD 005 DEACB 005 LUGGR 002 NUTSL 005 WASRD 006

QTY
1 1 1 1 1 2 4

DESCRIPTION
MACHINE BOLT, 7/8" X 22", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 24", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED DEADEND CLAMP (.7 1.39") 35,000# STRENGTH, GAP = 1 7/16", PIN = " DEADEND COMPRESSION ASSEMBLY FOR 954 ACSR, OVAL EYE LUG FOR 7/8" BOLT, #4 SOLID WIRE, TIN PLATED COPPER COMPRESSION SQUARE LOCK NUT FOR 7/8" BOLT, H.D.G. ROUND WASHER FOR 7/8" BOLT, 2 1/2" DIAMETER, GALVANIZED

ISDD9FSC1*1590 NO. ITEM ID

12 12 21 42 58 62 76 BOLMS 062 BOLMS 063 CLAQD 006 DEACB 007 LUGGR 003 NUTSL 006 WASRD 007

QTY
1 1 1 1 1 2 4

DESCRIPTION
MACHINE BOLT, 1" X 22", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 1" X 24", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED DEADEND CLAMP (1.18 - 1.52") 35,000# STRENGTH, GAP = 2", PIN = 3/4" DEADEND COMPRESSION ASSEMBLY FOR 1590 ACSR, OVAL EYE LUG FOR 1" BOLT, #4 SOLID WIRE, TIN PLATED COPPER COMPRESSION SQUARE LOCK NUT FOR 1" BOLT, H.D.G. ROUND WASHER FOR 1" BOLT, 2 1/2" DIAMETER, GALVANIZED

REVISED/REVIEWED: OCTOBER 2012

REVISED/REVIEWED BY: MLR

APPROVED BY: RHS

230kV INSULATORS
CIN-17

Overhead Transmission Standards

ISDD9FSC3
INSULATOR FOR SPUN CONCRETE POLES DOUBLE DEAD-END 90, FULL TENSION TO SLACK TENSION, 230KV, 3-PHASE
CONDUCTOR OPTIONS: 954S, 1590

NOTE: SEE MBA1 FOR BOLT ASSEMBLY DETAILS FULL TENSION SIDES SUBSTRUCTURE UPPER BOLT A LENGTH (INCHES) LOWER BOLT B LENGTH (INCHES)

Top 25.4 23.8

Mid 27.8 26.1

Bottom 30.1 28.5

SLACK TENSION SIDES SUBSTRUCTURE UPPER BOLT A LENGTH (INCHES) LOWER BOLT B LENGTH (INCHES)

Top 24.1 23.4

Mid 26.5 25.8

Bottom 28.9 28.1

NOTE: BOLT CALCULATIONS ASSUME A 17" POLE TOP DIAMETER

REVISED/REVIEWED: OCTOBER 2012

REVISED/REVIEWED BY: MLR

APPROVED BY: RHS

230kV INSULATORS
CIN-18

Overhead Transmission Standards

ISDD9FSC3 PLATES
ISDD9FSC3 BASE NO. ITEM ID
1 12 12 12 12 24 26 26 31 36 50 58 62 72 76 77 ADCVF 001 BOLMS 053 BOLMS 054 BOLMS 055 BOLMS 073 CLATG 001 CLEHL 005 CLEHL 008 CNNCP 016 COBCO 028 INSDE 002 LUGGR 002 NUTSL 005 TEEDE 003 WASRD 006 WASSC 002

QTY
3 1 2 1 2 3 3 3 3 18 ft 6 3 6 9 12 6

DESCRIPTION
VOID FILLER COMPOUND FOR DEADEND ASSEMBLY MACHINE BOLT, 7/8" X 24", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 26", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 28", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 30", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED CLAMP, TRANSFORMER TANK GROUND, BRONZE, #6 SOL - #1 STR SOCKET-Y CLEVIS, CLASS 52-8/11, L = 11", PIN = 7/8", H.D.G. SOCKET-EYE CLEVIS, CLASS 52-8/11, L = 10", EYE = 3/4" THICK W/ 13/16" OPENING, H. D. G. COMPRESSION CONNECTOR, #4 SOL. CU. TO #4 SOL. CU., COPPER #4 SOLID BARE COPPER CONDUCTOR, SOFT DRAWN DEADEND SILICON INSULATOR, Y-BALL COUPLING, 230KV, L = 111", CLASS 52-8/11 LUG FOR 7/8" BOLT, #4 SOLID WIRE, TIN PLATED COPPER COMPRESSION SQUARE LOCK NUT FOR 7/8" BOLT, H.D.G. TEE, DUCTILE IRON, HOT-DIP GALVANIZED, 6" HOLE SPACING, STRENGTH = 60,000# ROUND WASHER FOR 7/8" BOLT, 2 1/2" DIAMETER, GALVANIZED SQUARE CURVED WASHER FOR 7/8" BOLTS, GALVANIZED, 4" X 4"

ISDD9FSC3*954S NO. ITEM ID

12 12 12 12 12 21 42 58 62 76 BOLMS 053 BOLMS 054 BOLMS 055 BOLMS 073 BOLMS 074 CLAQD 005 DEACB 005 LUGGR 002 NUTSL 005 WASRD 006

QTY
1 1 2 1 1 3 3 3 6 12

DESCRIPTION
MACHINE BOLT, 7/8" X 24", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 26", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 28", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 30", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 32", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED DEADEND CLAMP (.7 1.39") 35,000# STRENGTH, GAP = 1 7/16", PIN = 3/4" DEADEND COMPRESSION ASSEMBLY FOR 954 ACSR, OVAL EYE LUG FOR 7/8" BOLT, #4 SOLID WIRE, TIN PLATED COPPER COMPRESSION SQUARE LOCK NUT FOR 7/8" BOLT, H.D.G. ROUND WASHER FOR 7/8" BOLT, 2 1/2" DIAMETER, GALVANIZED

ISDD9FSC3*1590 NO. ITEM ID

12 12 12 12 12 21 42 58 62 76 BOLMS 063 BOLMS 064 BOLMS 070 BOLMS 071 BOLMS 072 CLAQD 006 DEACB 007 LUGGR 003 NUTSL 006 WASRD 007

QTY
1 1 2 1 1 3 3 3 6 12

DESCRIPTION
MACHINE BOLT, 1" X 24", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 1" X 26", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 1" X 28", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 1" X 30", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 1" X 32", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED DEADEND CLAMP (1.18 - 1.52") 35,000# STRENGTH, GAP = 2", PIN = 3/4" DEADEND COMPRESSION ASSEMBLY FOR 1590 ACSR, OVAL EYE LUG FOR 1" BOLT, #4 SOLID WIRE, TIN PLATED COPPER COMPRESSION SQUARE LOCK NUT FOR 1" BOLT, H.D.G. ROUND WASHER FOR 1" BOLT, 2 1/2" DIAMETER, GALVANIZED

REVISED/REVIEWED: OCTOBER 2012

REVISED/REVIEWED BY: MLR

APPROVED BY: RHS

230kV INSULATORS
CIN-19

Overhead Transmission Standards

ISDD9SSC3
INSULATOR FOR SPUN CONCRETE POLES DOUBLE DEAD-END 90, SLACK TENSION TO SLACK TENSION, 230KV, 3-PHASE
CONDUCTOR OPTIONS: 954A, 954S, 1590

NOTE: SEE MBA1 FOR BOLT ASSEMBLY DETAILS

SUBSTRUCTURE Top UPPER BOLT A LENGTH (INCHES) LOWER BOLT B LENGTH (INCHES) 25.3 23.6

UPPER TEE Mid 27.7 26.0 Bottom 30.0 28.4 Top 25.3 23.7

LOWER TEE Mid 27.7 26.1 Bottom 30.1 28.4

NOTE: BOLT CALCULATIONS ASSUME A 17" POLE TOP DIAMETER

REVISED/REVIEWED: OCTOBER 2012

REVISED/REVIEWED BY: MLR

APPROVED BY: RHS

230kV INSULATORS
CIN-20

Overhead Transmission Standards

ISDD9SSC3 PLATES
ISDD9SSC3 BASE NO. ITEM ID
12 12 12 12 12 24 26 31 36 50 58 62 72 76 BOLMS 053 BOLMS 054 BOLMS 055 BOLMS 073 BOLMS 074 CLATG 001 CLEHL 008 CNNCP 016 COBCO 028 INSDE 002 LUGGR 002 NUTSL 005 TEEDE 003 WASRD 006

QTY
2 2 4 2 2 3 6 6 18 ft 6 6 12 12 24

DESCRIPTION
MACHINE BOLT, 7/8" X 24", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 26", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 28", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 30", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 32", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED CLAMP, TRANSFORMER TANK GROUND, BRONZE, #6 SOL - #1 STR SOCKET-EYE CLEVIS, CLASS 52-8/11, L = 10", EYE = 3/4" THICK W/ 13/16" OPENING, H. D. G. COMPRESSION CONNECTOR, #4 SOL. CU. TO #4 SOL. CU., COPPER #4 SOLID BARE COPPER CONDUCTOR, SOFT DRAWN DEADEND SILICON INSULATOR, Y-BALL COUPLING, 230KV, L = 111", CLASS 52-8/11 LUG FOR 7/8" BOLT, #4 SOLID WIRE, TIN PLATED COPPER COMPRESSION SQUARE LOCK NUT FOR 7/8" BOLT, H.D.G. TEE, DUCTILE IRON, HOT-DIP GALVANIZED, 6" HOLE SPACING, STRENGTH = 60,000# ROUND WASHER FOR 7/8" BOLT, 2 1/2" DIAMETER, GALVANIZED

ISDD9SSC3*954A NO. ITEM ID

21 68 CLAQD 005 SLEAJ 006

QTY
6 3

DESCRIPTION
DEADEND CLAMP (.7 1.39") 35,000# STRENGTH, GAP = 1 7/16", PIN = 3/4" ALUM. SLEEVE JUMPER FOR 954 AAC 61, COMPRESSION SPLICE, NON-TENSION ONLY

ISDD9SSC3*954S NO. ITEM ID

21 68 CLAQD 005 SLEAJ 005

QTY
6 3

DESCRIPTION
DEADEND CLAMP (.7 1.39") 35,000# STRENGTH, GAP = 1 7/16", PIN = 3/4" ALUM. SLEEVE JUMPER FOR 954 ACSR 54/7, COMPRESSION SPLICE, NON-TENSION ONLY

ISDD9SSC3*1590 NO. ITEM ID

21 68 CLAQD 006 SLEAJ 007

QTY
6 3

DESCRIPTION
DEADEND CLAMP (1.18 - 1.52") 35,000# STRENGTH, GAP = 2", PIN = 3/4" ALUM. SLEEVE JUMPER FOR 1590 ACSR 54/19, COMPRESSION SPLICE, NON-TENSION ONLY

REVISED/REVIEWED: OCTOBER 2012

REVISED/REVIEWED BY: MLR

APPROVED BY: RHS

230kV INSULATORS
CIN-21

Overhead Transmission Standards

ISSBBGC3
INSULATOR FOR SPUN CONCRETE POLES SINGLE BRACED LINE POST BOTTOM GUY, 230KV, 3-PHASE
CONDUCTOR OPTIONS: 954A, 954S, 1590

SEE MBA1 FOR BOLT ASSEMBLY DETAILS MINIMUM REQUIRED BOLT LENGTH (INCHES) STRUCTURE TOP MIDDLE BOTTOM NOTE: A 21.0 23.2 25.3 B 20.9 23.0 25.2 C 23.6 25.8 28.0 D 28.2 30.3 32.5 E 28.3 30.5 32.7

BOLT CALCULATIONS ASSUME A 17" POLE TOP DIAMETER

REVISED/REVIEWED: OCTOBER 2012

REVISED/REVIEWED BY: MLR

APPROVED BY: RHS

230kV INSULATORS
CIN-22

Overhead Transmission Standards

ISSBBGC3 PLATES
ISSBBGC3 BASE NO. ITEM ID
10 11 11 11 12 12 12 12 12 12 12 24 26 36 53 58 62 69 72 76 77 BKTLP 002 BOLDA 036 BOLDA 037 BOLDA 038 BOLMS 052 BOLMS 053 BOLMS 054 BOLMS 055 BOLMS 073 BOLMS 074 BOLMS 075 CLATG 001 CLEHL 001 COBCO 028 INSLP 014 LUGGR 002 NUTSL 005 SOCEY 003 TEEDE 003 WASRD 006 WASSC 002

QTY
3 1 1 1 2 3 3 1 1 1 1 3 3 15 ft 3 6 18 3 3 33 15

DESCRIPTION
BRACKET, 53 ANGLE, 6" HOLE SPACING, 1 1/16" HOLE DIAMETER, 5/8" THICK DOUBLE ARMING BOLT, 7/8" X 30", WITH 4 SQUARE NUTS ATTACHED DOUBLE ARMING BOLT, 7/8" X 32", WITH 4 SQUARE NUTS ATTACHED DOUBLE ARMING BOLT, 7/8" X 34", WITH 4 SQUARE NUTS ATTACHED MACHINE BOLT, 7/8" X 22", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 24", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 26", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 26", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 30", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 32", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 36", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED CLAMP, TRANSFORMER TANK GROUND, BRONZE, #6 SOL - #1 STR BALL-Y CLEVIS, CLASS 52-3/5, STRENGTH = 30,000#, L > 9", PIN = 3/4", H.D.G. #4 SOLID BARE COPPER CONDUCTOR, SOFT DRAWN 230KV SILICONE BRACED LINE POST INSULATOR, 17 RISE, GAIN BASE, L = 108", H = 94", 14" B.H.S. LUG FOR 7/8" BOLT, #4 SOLID WIRE, TIN PLATTED COPPER COMPRESSION SQUARE LOCK NUT FOR 7/8" BOLT, H.D.G. SOCKET - EYE, STENGTH = 25,000#, L = 2 5/16", EYE = 13/16", FORGED STEEL, GALV. TEE, DUCTILE IRON, HOT-DIP GALVANIZED, 6" HOLE SPACING, STRENGTH = 60,000# ROUND WASHER FOR 7/8" BOLT, 2 " DIAMETER, GALVANIZED SQUARE CURVED WASHER FOR 7/8" BOLTS, RIBBED MALLEABLE IRON-GALVANIZED, 4" X 4"

ISSBBGC3*954A
45 GRISA 003 3 ARMOR GRIP SUSPENSION ASSEMBLY FOR 954 AAC, 82", 1 3/16" GAP, 5/8" PIN

ISSBBGC3*954S
45 GRISA 004 3 ARMOR GRIP SUSPENSION ASSEMBLY FOR 954 ACSR, 82", 1 3/16" GAP, 5/8" PIN

ISSBBGC3*1590
45 GRISA 005 3 ARMOR GRIP SUSPENSION ASSEMBLY FOR 1590 ACSR, 88", 1 3/8" GAP, 3/4" PIN

REVISED/REVIEWED: OCTOBER 2012

REVISED/REVIEWED BY: MLR

APPROVED BY: RHS

230kV INSULATORS
CIN-23

Overhead Transmission Standards

ISSBDC3
INSULATOR FOR SPUN CONCRETE POLES SINGLE BRACED LINE POST, DELTA CONFIGURATION, 230KV, 3-PHASE
CONDUCTOR OPTIONS: 954A, 954S, 1590

SEE MBA1 FOR BOLT ASSEMBLY DETAILS

MINIMUM REQUIRED BOLT LENGTH (INCHES) STRUCTURE TOP MIDDLE BOTTOM NOTE: A 21.9 23.0 24.1 B 22.3 23.4 24.4 C 29.3 30.4 31.4 D 29.3 30.4 31.5

BOLT CALCULATIONS ASSUME A 17" POLE TOP DIAMETER

REVISED/REVIEWED: OCTOBER 2012

REVISED/REVIEWED BY: MLR

APPROVED BY: RHS

230kV INSULATORS
CIN-24

Overhead Transmission Standards

ISSBDC3 PLATES

ISSBDC3 BASE NO. ITEM ID

10 12 12 12 12 24 26 36 53 58 62 69 76 77 BKTLP 002 BOLMS 053 BOLMS 054 BOLMS 073 BOLMS 074 CLATG 001 CLEHL 001 COBCO 028 INSLP 014 LUGGR 002 NUTSL 005 SOCEY 003 WASRD 006 WASSC 002

QTY
3 4 2 2 4 4 3 9 FT 3 6 12 3 24 12

DESCRIPTION
BRACKET, 53 ANGLE, 6" HOLE SPACING, 1 1/16" HOLE DIAMETER, 5/8" THICK MACHINE BOLT, 7/8" X 24", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 26", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 30", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 32", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED CLAMP, TRANSFORMER TANK GROUND, BRONZE, #6 SOL - #1 STR BALL-Y CLEVIS, CLASS 52-3/5, STRENGTH = 30,000#, L > 9", PIN = 3/4", H.D.G. #4 SOLID BARE COPPER CONDUCTOR, SOFT DRAWN 230KV SILICONE BRACED LINE POST INSULATOR, 17 RISE, GAIN BASE, L = 108", H = 94", 14" B.H.S. LUG FOR 7/8" BOLT, #4 SOLID WIRE, TIN PLATTED COPPER COMPRESSION SQUARE LOCK NUT FOR 7/8" BOLT, H.D.G. SOCKET - EYE, STENGTH = 25,000#, L = 2 5/16", EYE = 13/16", FORGED STEEL, GALV. ROUND WASHER FOR 7/8" BOLT, 2 1/2" DIAMETER, GALVANIZED SQUARE CURVED WASHER FOR 7/8" BOLTS, RIBBED MALLEABLE IRON-GALVANIZED, 4" X 4"

ISSBDC3*954A
45 GRISA 003 3 ARMOR GRIP SUSPENSION ASSEMBLY FOR 954 AAC, 82", 1 3/16" GAP, 5/8" PIN

ISSBDC3*954S
45 GRISA 004 3 ARMOR GRIP SUSPENSION ASSEMBLY FOR 954 ACSR, 82", 1 3/16" GAP, 5/8" PIN

ISSBDC3*1590
45 GRISA 005 3 ARMOR GRIP SUSPENSION ASSEMBLY FOR 1590 ACSR, 88", 1 3/8" GAP, 3/4" PIN

REVISED/REVIEWED: OCTOBER 2012

REVISED/REVIEWED BY: MLR

APPROVED BY: RHS

230kV INSULATORS
CIN-25

Overhead Transmission Standards

ISSBNGC3
INSULATOR FOR SPUN CONCRETE POLES SINGLE BRACED LINE POST, NO GUY, 230KV
CONDUCTOR OPTIONS: 954A, 954S, 1590

SEE MBA1 FOR BOLT ASSEMBLY DETAILS

MINIMUM REQUIRED BOLT LENGTH (INCHES) STRUCTURE TOP MIDDLE BOTTOM A 21.0 23.2 25.3 B 20.9 23.0 25.2 C 27.8 30.0 32.2 D 28.3 30.5 32.7

NOTE:

BOLT CALCULATIONS ASSUME A 17" POLE TOP DIAMETER

REVISED/REVIEWED: OCTOBER 2012

REVISED/REVIEWED BY: MLR

APPROVED BY: RHS

230kV INSULATORS
CIN-26

Overhead Transmission Standards

ISSBNGC3 PLATES

ISSBNGC3 BASE NO. ITEM ID

10 12 12 12 12 12 12 12 24 26 36 53 58 62 69 76 77 BKTLP 002 BOLMS 052 BOLMS 053 BOLMS 054 BOLMS 055 BOLMS 073 BOLMS 074 BOLMS 075 CLATG 001 CLEHL 001 COBCO 028 INSLP 014 LUGGR 002 NUTSL 005 SOCEY 003 WASRD 006 WASSC 002

QT Y
3 2 2 2 1 1 2 2 3 3 9 FT 3 6 12 3 24 12

DESCRIPTION
BRACKET, 53 ANGLE, 6" HOLE SPACING, 1 1/16" HOLE DIAMETER, 5/8" THICK MACHINE BOLT, 7/8" X 22", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 24", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 26", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 28", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 30", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 32", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 36", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED CLAMP, TRANSFORMER TANK GROUND, BRONZE, #6 SOL - #1 STR BALL-Y CLEVIS, CLASS 52-3/5, STRENGTH = 30,000#, L > 9", PIN = 3/4", H.D.G. #4 SOLID BARE COPPER CONDUCTOR, SOFT DRAWN 230KV SILICONE BRACED LINE POST INSULATOR, 17 RISE, GAIN BASE, L = 108", H = 94", 14" B.H.S. LUG FOR 7/8" BOLT, #4 SOLID WIRE, TIN PLATTED COPPER COMPRESSION SQUARE LOCK NUT FOR 7/8" BOLT, H.D.G. SOCKET - EYE, STENGTH = 25,000#, L = 2 5/16", EYE = 13/16", FORGED STEEL, GALV. ROUND WASHER FOR 7/8" BOLT, 2 1/2" DIAMETER, GALVANIZED SQUARE CURVED WASHER FOR 7/8" BOLTS, RIBBED MALLEABLE IRON-GALVANIZED, 4" X 4"

ISSBNGC3*954A
45 GRISA 003 3 ARMOR GRIP SUSPENSION ASSEMBLY FOR 954 AAC, 82", 1 3/16" GAP, 5/8" PIN

ISSBNGC3*954S
45 GRISA 004 3 ARMOR GRIP SUSPENSION ASSEMBLY FOR 954 ACSR, 82", 1 3/16" GAP, 5/8" PIN

ISSBNGC3*1590
45 GRISA 005 3 ARMOR GRIP SUSPENSION ASSEMBLY FOR 1590 ACSR, 88", 1 3/8" GAP, 3/4" PIN

REVISED/REVIEWED: OCTOBER 2012

REVISED/REVIEWED BY: MLR

APPROVED BY: RHS

230kV INSULATORS
CIN-27

Overhead Transmission Standards

ISSBTGC3
INSULATOR FOR SPUN CONCRETE POLES SINGLE BRACED LINE POST, TOP GUY, 230KV, 3-PHASE
CONDUCTOR OPTIONS: 954A, 954S, 1590

SEE MBA1 FOR BOLT ASSEMBLY DETAILS

MINIMUM REQUIRED BOLT LENGTH (INCHES) STRUCTURE TOP MIDDLE BOTTOM A 22.3 24.5 26.6 B 21.2 23.3 25.5 C 27.8 30.0 32.2 D 28.3 30.5 32.7

NOTE:

BOLT CALCULATIONS ASSUME A 17" POLE TOP DIAMETER

REVISED/REVIEWED: OCTOBER 2012

REVISED/REVIEWED BY: MLR

APPROVED BY: RHS

230kV INSULATORS
CIN-28

Overhead Transmission Standards

ISSBTGC3 PLATES
ISSBTGC3 BASE NO. ITEM ID
10 12 12 12 12 12 12 12 24 26 36 53 58 62 69 72 76 77 BKTLP 002 BOLMS 052 BOLMS 053 BOLMS 054 BOLMS 055 BOLMS 073 BOLMS 074 BOLMS 075 CLATG 001 CLEHL 001 COBCO 028 INSLP 014 LUGGR 002 NUTSL 005 SOCEY 003 TEEDE 003 WASRD 006 WASSC 002

QT Y
3 1 2 1 3 3 2 2 3 3 15 ft 3 6 12 3 4 24 6

DESCRIPTION
BRACKET, 53 ANGLE, 6" HOLE SPACING, 1 1/16" HOLE DIAMETER, 5/8" THICK MACHINE BOLT, 7/8" X 22", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 24", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 26", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 28", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 30", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 32", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 36", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED CLAMP, TRANSFORMER TANK GROUND, BRONZE, #6 SOL - #1 STR BALL-Y CLEVIS, CLASS 52-3/5, STRENGTH = 30,000#, L > 9", PIN = 3/4", H.D.G. #4 SOLID BARE COPPER CONDUCTOR, SOFT DRAWN 230KV SILICONE BRACED LINE POST INSULATOR, 17 RISE, GAIN BASE, L = 108", H = 94", 14" B.H.S. LUG FOR 7/8" BOLT, #4 SOLID WIRE, TIN PLATTED COPPER COMPRESSION SQUARE LOCK NUT FOR 7/8" BOLT, H.D.G. SOCKET EYE, STENGTH = 25,000#, L = 2 5/16", EYE = 13/16", FORGED STEEL, GALV. TEE, DUCTILE IRON, HOT-DIP GALVANIZED, 6" HOLE SPACING, STRENGTH = 60,000# ROUND WASHER FOR 7/8" BOLT, 2 1/2" DIAMETER, GALVANIZED SQUARE CURVED WASHER FOR 7/8" BOLTS, RIBBED MALLEABLE IRON-GALVANIZED, 4" X 4"

ISSBTGC3*954A
45 GRISA 003 3 ARMOR GRIP SUSPENSION ASSEMBLY FOR 954 AAC, 82", 1 3/16" GAP, 5/8" PIN

ISSBTGC3*954S
45 GRISA 004 3 ARMOR GRIP SUSPENSION ASSEMBLY FOR 954 ACSR, 82", 1 3/16" GAP, 5/8" PIN

ISSBTGC3*1590
45 GRISA 005 3 ARMOR GRIP SUSPENSION ASSEMBLY FOR 1590 ACSR, 88", 1 3/8" GAP, 3/4" PIN

REVISED/REVIEWED: OCTOBER 2012

REVISED/REVIEWED BY: MLR

APPROVED BY: RHS

230kV INSULATORS
CIN-29

Overhead Transmission Standards

ISSDFC3
INSULATOR FOR SPUN CONCRETE POLES SINGLE DEAD-END FULL TENSION, 230KV, 3-PHASE
CONDUCTOR OPTIONS: 954S, 1590

NOTE: SEE MBA1 FOR BOLT ASSEMBLY DETAILS

SUBSTRUCTURE UPPER BOLT A LENGTH (INCHES) LOWER BOLT B LENGTH (INCHES)

Top 25.4 23.8

Mid 27.8 26.1

Bottom 30.1 28.5

NOTE: BOLT CALCULATIONS ASSUME A 17" POLE TOP DIAMETER

REVISED/REVIEWED: OCTOBER 2012

REVISED/REVIEWED BY: MLR

APPROVED BY: RHS

230kV INSULATORS
CIN-30

Overhead Transmission Standards

ISSDFC3 PLATES
ISSDFC3 BASE NO. ITEM ID
1 24 26 36 50 72 ADCVF 001 CLATG 001 CLEHL 005 COBCO 028 INSDE 002 TEEDE 003

QTY
3 3 3 12 ft 3 6

DESCRIPTION
VOID FILLER COMPOUND FOR DEADEND ASSEMBLY CLAMP, TRANSFORMER TANK GROUND, BRONZE, #6 SOL - #1 STR SOCKET-Y CLEVIS, CLASS 52-8/11, L = 11", PIN = 7/8", H.D.G. #4 SOLID BARE COPPER CONDUCTOR, SOFT DRAWN DEADEND SILICON INSULATOR, Y-BALL COUPLING, 230KV, L = 111", CLASS 52-8/11 TEE, DUCTILE IRON, HOT-DIP GALVANIZED, 6" HOLE SPACING, STRENGTH = 60,000#

ISSDFC3*954S NO. ITEM ID

12 12 12 12 12 42 58 62 76 BOLMS 053 BOLMS 054 BOLMS 055 BOLMS 073 BOLMS 074 DEACB 005 LUGGR 002 NUTSL 005 WASRD 006

QTY
1 1 2 1 1 3 3 6 12

DESCRIPTION
MACHINE BOLT, 7/8" X 24", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 26", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 28", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 30", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 32", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED DEADEND COMPRESSION ASSEMBLY FOR 954 ACSR, OVAL EYE LUG FOR 7/8" BOLT, #4 SOLID WIRE, TIN PLATED COPPER COMPRESSION SQUARE LOCK NUT FOR 7/8" BOLT, H.D.G. ROUND WASHER FOR 7/8" BOLT, 2 1/2" DIAMETER, GALVANIZED

ISSDFC3*1590 NO. ITEM ID

12 12 12 12 12 42 58 62 76 BOLMS 063 BOLMS 064 BOLMS 070 BOLMS 071 BOLMS 072 DEACB 007 LUGGR 003 NUTSL 006 WASRD 007

QTY
1 1 2 1 1 3 3 6 12

DESCRIPTION
MACHINE BOLT, 1" X 24", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 1" X 26", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 1" X 28", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 1" X 30", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 1" X 32", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED DEADEND COMPRESSION ASSEMBLY FOR 1590 ACSR, OVAL EYE LUG FOR 1" BOLT, #4 SOLID WIRE, TIN PLATED COPPER COMPRESSION SQUARE LOCK NUT FOR 1" BOLT, H.D.G. ROUND WASHER FOR 1" BOLT, 2 1/2" DIAMETER, GALVANIZED

REVISED/REVIEWED: OCTOBER 2012

REVISED/REVIEWED BY: MLR

APPROVED BY: RHS

230kV INSULATORS
CIN-31

Overhead Transmission Standards

ISSDFP2C3
INSULATOR FOR SPUN CONCRETE POLES SINGLE DEAD-END, FULL TENSION TO POST, TYPE 2, 230KV, 3-PHASE
CONDUCTOR OPTIONS: 954S, 1590

NOTE: SEE MBA1 FOR BOLT ASSEMBLY DETAILS SUBSTRUCTURE BOLT A LENGTH (INCHES) BOLT B LENGTH (INCHES) BOLT C LENGTH (INCHES) BOLT D LENGTH (INCHES) Top 21.4 19.8 24.7 24.7 Mid 23.8 22.1 27.1 27.1 Bottom 26.2 24.5 29.5 29.5

NOTE: BOLT CALCULATIONS ASSUME A 17" POLE TOP DIAMETER

REVISED/REVIEWED: OCTOBER 2012

REVISED/REVIEWED BY: MLR

APPROVED BY: RHS

230kV INSULATORS
CIN-32

Overhead Transmission Standards

ISSDFP2C3
ISSDFP2C3 BASE NO. ITEM ID
1 12 12 12 24 26 26 36 50 51 58 62 69 72 76 77 ADCVF 001 BOLMS 054 BOLMS 055 BOLMS 073 CLATG 001 CLEHL 001 CLEHL 005 COBCO 028 INSDE 002 INSHP 025 LUGGR 002 NUTSL 005 SOCEY 003 TEEDE 003 WASRD 006 WASSC 002

QTY
3 2 2 2 3 3 3 12 ft 3 3 3 6 3 6 12 6

DESCRIPTION
VOID FILLER COMPOUND FOR DEADEND ASSEMBLY MACHINE BOLT, 7/8" X 26", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 28", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 30", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED CLAMP, TRANSFORMER TANK GROUND, BRONZE, #6 SOL - #1 STR BALL-Y CLEVIS, CLASS 52-3/5, STRENGTH = 30,000#, L > 9, PIN = 3/4, H.D.G. SOCKET-Y CLEVIS, CLASS 52-8/11, L = 11", PIN = 7/8", H.D.G. #4 SOLID BARE COPPER CONDUCTOR, SOFT DRAWN DEADEND SILICON INSULATOR, Y-BALL COUPLING, 230KV, L = 111", CLASS 52-8/11 HORIZONTAL POST INSULATOR, 230KV, L = 86", GAIN BASE, 17 RISE LUG FOR 7/8" BOLT, #4 SOLID WIRE, TIN PLATED COPPER COMPRESSION SQUARE LOCK NUT FOR 7/8" BOLT, H.D.G. SOCKET-EYE, STRENGTH = 25,000#, L = 2 5/16, EYE = 13/16, FORGED STEEL, GALV. TEE, DUCTILE IRON, HOT-DIP GALVANIZED, 6" HOLE SPACING, STRENGTH = 60,000# ROUND WASHER FOR 7/8" BOLT, 2 1/2" DIAMETER, GALVANIZED SQUARE CURVED WASHER FOR 7/8" BOLTS, RIBBED MALLEABLE IRON-GALVANIZED, 4" X 4"

ISSDFP2C3*954S NO. ITEM ID

12 12 12 12 12 42 45 58 62 76 BOLMS 051 BOLMS 052 BOLMS 053 BOLMS 054 BOLMS 055 DEACB 005 GRISA 004 LUGGR 002 NUTSL 005 WASRD 006

QTY
1 1 2 1 1 3 3 3 6 12

DESCRIPTION
MACHINE BOLT, 7/8" X 20", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 22", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 24", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 26", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 28", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED DEADEND COMPRESSION ASSEMBLY FOR 954 ACSR, OVAL EYE ARMOR GRIP SUSPENSION ASSEMBLY FOR 954 ACSR, 82, 1 3/16 GAP, 5/8 PIN LUG FOR 7/8" BOLT, #4 SOLID WIRE, TIN PLATED COPPER COMPRESSION SQUARE LOCK NUT FOR 7/8" BOLT, H.D.G. ROUND WASHER FOR 7/8" BOLT, 2 1/2" DIAMETER, GALVANIZED

ISSDFP2C3*1590 NO. ITEM ID

12 12 12 12 12 42 45 58 62 76 BOLMS 061 BOLMS 062 BOLMS 063 BOLMS 064 BOLMS 070 DEACB 007 GRISA 005 LUGGR 003 NUTSL 006 WASRD 007

QTY
1 1 2 1 2 3 3 3 6 12

DESCRIPTION
MACHINE BOLT, 1" X 20", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 1" X 22", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 1" X 24", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 1" X 26", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 1" X 28", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED DEADEND COMPRESSION ASSEMBLY FOR 1590 ACSR, OVAL EYE ARMOR GRIP SUSPENSION ASSEMBLY FOR 1590 ACSR, 88, 1 3/8 GAP, 3/4 PIN LUG FOR 1" BOLT, #4 SOLID WIRE, TIN PLATED COPPER COMPRESSION SQUARE LOCK NUT FOR 1" BOLT, H.D.G. ROUND WASHER FOR 1" BOLT, 2 1/2" DIAMETER, GALVANIZED

REVISED/REVIEWED: OCTOBER 2012

REVISED/REVIEWED BY: MLR

APPROVED BY: RHS

230kV INSULATORS
CIN-33

Overhead Transmission Standards

ISSDFP3C3
INSULATOR FOR SPUN CONCRETE POLES SINGLE DEAD-END, FULL TENSION TO POST, TYPE 3, 230KV, 3-PHASE
CONDUCTOR OPTIONS: 954S, 1590

NOTE: SEE MBA1 FOR BOLT ASSEMBLY DETAILS SUBSTRUCTURE BOLT A LENGTH (INCHES) BOLT B LENGTH (INCHES) BOLT C LENGTH (INCHES) BOLT D LENGTH (INCHES) Top 25.4 23.8 28.5 29.0 Mid 27.8 26.1 30.8 31.3 Bottom 30.1 28.5 33.2 33.7

NOTE: BOLT CALCULATIONS ASSUME A 17" POLE TOP DIAMETER

REVISED/REVIEWED: OCTOBER 2012

REVISED/REVIEWED BY: MLR

APPROVED BY: RHS

230kV INSULATORS
CIN-34

Overhead Transmission Standards

ISSDFP3C3 PLATES
ISSDFP3C3 BASE NO. ITEM ID
1 12 12 12 24 26 36 50 51 58 62 72 76 77 ADCVF 001 BOLMS 073 BOLMS 074 BOLMS 075 CLATG 001 CLEHL 005 COBCO 028 INSDE 002 INSHP 025 LUGGR 002 NUTSL 005 TEEDE 003 WASRD 006 WASSC 002

QTY
3 2 2 2 3 3 12 ft 3 3 3 6 6 12 6

DESCRIPTION
VOID FILLER COMPOUND FOR DEADEND ASSEMBLY MACHINE BOLT, 7/8" X 30", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 32", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 36", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED CLAMP, TRANSFORMER TANK GROUND, BRONZE, #6 SOL - #1 STR SOCKET-Y CLEVIS, CLASS 52-8/11, L = 11", PIN = 7/8", H.D.G. #4 SOLID BARE COPPER CONDUCTOR, SOFT DRAWN DEADEND SILICON INSULATOR, Y-BALL COUPLING, 230KV, L = 111", CLASS 52-8/11 HORIZONTAL POST INSULATOR, 230KV, L = 86", GAIN BASE, 17 RISE LUG FOR 7/8" BOLT, #4 SOLID WIRE, TIN PLATED COPPER COMPRESSION SQUARE LOCK NUT FOR 7/8" BOLT, H.D.G. TEE, DUCTILE IRON, HOT-DIP GALVANIZED, 6" HOLE SPACING, STRENGTH = 60,000# ROUND WASHER FOR 7/8" BOLT, 2 1/2" DIAMETER, GALVANIZED SQUARE CURVED WASHER FOR 7/8" BOLTS, RIBBED MALLEABLE IRON-GALVANIZED, 4" X 4"

ISSDFP3C3*954S NO. ITEM ID

12 12 12 12 12 22 28 42 58 62 76 83 BOLMS 053 BOLMS 054 BOLMS 055 BOLMS 073 BOLMS 074 CLASU 006 CLETE 005 DEACB 005 LUGGR 002 NUTSL 005 WASRD 006 RODAR 007

QTY
1 1 2 1 1 3 3 3 3 6 12 3

DESCRIPTION
MACHINE BOLT, 7/8" X 24", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 26", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 28", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 30", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 32", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED CLAMP, SUSPENSION, ALUMINUM, FOR 954 ASCR Y-EYE CLEVIS DEADEND COMPRESSION ASSEMBLY FOR 954 ACSR, OVAL EYE LUG FOR 7/8" BOLT, #4 SOLID WIRE, TIN PLATED COPPER COMPRESSION SQUARE LOCK NUT FOR 7/8" BOLT, H.D.G. ROUND WASHER FOR 7/8" BOLT, 2 1/2" DIAMETER, GALVANIZED ARMOR ROD FOR 954 ASCR, 100"

ISSDFP3C3*1590 NO. ITEM ID

12 12 12 12 12 22 28 42 58 62 76 83 BOLMS 063 BOLMS 064 BOLMS 070 BOLMS 071 BOLMS 072 CLASU 007 CLETE 006 DEACB 007 LUGGR 003 NUTSL 006 WASRD 007 RODAR 008

QTY
1 1 2 1 1 3 3 3 3 6 12 3

DESCRIPTION
MACHINE BOLT, 1" X 24", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 1" X 26", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 1" X 28", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 1" X 30", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 1" X 32", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED CLAMP, SUSPENSION, ALUMINUM, FOR 1590 ASCR Y-EYE CLEVIS DEADEND COMPRESSION ASSEMBLY FOR 1590 ACSR, OVAL EYE LUG FOR 1" BOLT, #4 SOLID WIRE, TIN PLATED COPPER COMPRESSION SQUARE LOCK NUT FOR 1" BOLT, H.D.G. ROUND WASHER FOR 1" BOLT, 2 1/2" DIAMETER, GALVANIZED ARMOR ROD FOR 1590 ASCR, 100"

REVISED/REVIEWED: OCTOBER 2012

REVISED/REVIEWED BY: MLR

APPROVED BY: RHS

230kV INSULATORS
CIN-35

Overhead Transmission Standards

ISSDSC3
INSULATOR FOR SPUN CONCRETE POLES SINGLE DEAD-END SLACK TENSION, 230KV, 3-PHASE
CONDUCTOR OPTIONS: 954A, 954S, 1590

NOTE: SEE MBA1 FOR BOLT ASSEMBLY DETAILS

SUBSTRUCTURE UPPER BOLT A LENGTH (INCHES) LOWER BOLT B LENGTH (INCHES)

Top 25.3 23.7

Mid 27.7 26.0

Bottom 30.0 28.4

NOTE: BOLT CALCULATIONS ASSUME A 17" POLE TOP DIAMETER

REVISED/REVIEWED: OCTOBER 2012

REVISED/REVIEWED BY: MLR

APPROVED BY: RHS

230kV INSULATORS
CIN-36

Overhead Transmission Standards

ISSDSC3 PLATES
ISSDSC3 BASE NO. ITEM ID
12 12 12 12 24 26 36 50 58 62 72 76 BOLMS 053 BOLMS 054 BOLMS 055 BOLMS 073 CLATG 001 CLEHL 008 COBCO 028 INSDE 002 LUGGR 002 NUTSL 005 TEEDE 003 WASRD 006

QTY
1 2 1 2 3 3 12 ft 3 3 6 6 12

DESCRIPTION
MACHINE BOLT, 7/8" X 24", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 26", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 28", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 30", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED CLAMP, TRANSFORMER TANK GROUND, BRONZE, #6 SOL - #1 STR SOCKET-EYE CLEVIS, CLASS 52-8/11, L = 10", EYE = 3/4" THICK W/ 13/16" OPENING, H. D. G. #4 SOLID BARE COPPER CONDUCTOR, SOFT DRAWN DEADEND SILICON INSULATOR, Y-BALL COUPLING, 230KV, L = 111", CLASS 52-8/11 LUG FOR 7/8" BOLT, #4 SOLID WIRE, TIN PLATED COPPER COMPRESSION SQUARE LOCK NUT FOR 7/8" BOLT, H.D.G. TEE, DUCTILE IRON, HOT-DIP GALVANIZED, 6" HOLE SPACING, STRENGTH = 60,000# ROUND WASHER FOR 7/8" BOLT, 2 1/2" DIAMETER, GALVANIZED

ISSDSC3*954A, 954S NO. ITEM ID

21 CLAQD 005

QTY
3

DESCRIPTION
DEADEND CLAMP (.7 1.39") 35,000# STRENGTH, GAP = 1 7/16", PIN = 3/4"

ISSDSC3*1590 NO. ITEM ID

21 CLAQD 006

QTY
3

DESCRIPTION
DEADEND CLAMP (1.18 - 1.52") 35,000# STRENGTH, GAP = 2", PIN = 3/4"

REVISED/REVIEWED: OCTOBER 2012

REVISED/REVIEWED BY: MLR

APPROVED BY: RHS

230kV INSULATORS
CIN-37

Overhead Transmission Standards

ISSSDGGC3
INSULATOR FOR SPUN CONCRETE POLES SINGLE SUSPENSION, DOUBLE GRIP, GUYED, 230KV, 3-PHASE
CONDUCTOR OPTIONS: 954A, 954S, 1590

NOTE: SEE MBA1 FOR BOLT ASSEMBLY DETAILS

DEADEND INSULATOR UPPER BOLT A LENGTH (INCHES) LOWER BOLT B LENGTH (INCHES)

TOP 25.7 24.0

MIDDLE 28.0 26.4

BOTTOM 30.4 28.8

NOTE:

BOLT CALCULATIONS ASSUME A 17" POLE TOP DIAMETER

REVISED/REVIEWED: OCTOBER 2012

REVISED/REVIEWED BY: MLR

APPROVED BY: RHS

230kV INSULATORS
CIN-38

Overhead Transmission Standards

ISSSDGGC3 PLATES
ISSSDGGC3 BASE NO. ITEM ID
24 26 36 56 67 72 80 CLATG 001 CLEHL 007 COBCO 028 INSSU 009 SHAAN 003 TEEDE 003 YOKPL 003

QTY
3 6 9 ft 6 6 6 3

DESCRIPTION
CLAMP, TRANSFORMER TANK GROUND, BRONZE, #6 SOL - #1 STR SOCKET-EYE CLEVIS, CLASS 52-3/5, L = 10", EYE = 3/4" THICK WITH 13/16" OPENING, H. D. G. #4 SOLID BARE COPPER CONDUCTOR, SOFT DRAWN DEADEND SILICON INSULATOR, Y-BALL COUPLING, 230KV, L = 89", CLASS 52-3/5 SHACKLE, 3/4", 50,000#, GALVANIZED TEE, DUCTILE IRON, HOT-DIP GALVANIZED, 6" HOLE SPACING, STRENGTH = 60,000# TRIANGULAR SUSPENSION YOKE PLATE, 16" SPACING, GLAVANIZED, 15/16" HOLE DIA.

ISSSDGGC3*954A NO. ITEM ID

12 12 12 12 45 58 62 76 BOLMS 054 BOLMS 055 BOLMS 073 BOLMS 074 GRISA 006 LUGGR 002 NUTSL 005 WASRD 006

QTY
2 2 1 1 3 3 6 12

DESCRIPTION
MACHINE BOLT, 7/8" X 26", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 28", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 30", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 32", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED DOUBLE AGS UNIT FOR 954A CONDUCTOR LUG FOR 7/8" BOLT, #4 SOLID WIRE, TIN PLATED COPPER COMPRESSION SQUARE LOCK NUT FOR 7/8" BOLT, H.D.G. ROUND WASHER FOR 7/8" BOLT, 2 " DIAMETER, GALVANIZED

ISSSDGGC3*954S NO. ITEM ID

12 12 12 12 45 58 62 76 BOLMS 054 BOLMS 055 BOLMS 073 BOLMS 074 GRISA 007 LUGGR 002 NUTSL 005 WASRD 006

QTY
2 2 1 1 3 3 6 12

DESCRIPTION
MACHINE BOLT, 7/8" X 26", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 28", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 30", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8" X 32", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED DOUBLE AGS UNIT FOR 954S CONDUCTOR LUG FOR 7/8" BOLT, #4 SOLID WIRE, TIN PLATED COPPER COMPRESSION SQUARE LOCK NUT FOR 7/8" BOLT, H.D.G. ROUND WASHER FOR 7/8" BOLT, 2 1/2" DIAMETER, GALVANIZED

ISSSDGGC3*1590 NO. ITEM ID

12 12 12 12 45 58 62 76 BOLMS 064 BOLMS 070 BOLMS 071 BOLMS 072 GRISA 008 LUGGR 003 NUTSL 006 WASRD 007

QTY
2 2 1 1 3 3 6 12

DESCRIPTION
MACHINE BOLT, 1" X 26", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 1" X 28", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 1" X 30", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 1" X 32", SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED DOUBLE AGS UNIT FOR 1590 CONDUCTOR LUG FOR 1" BOLT, #4 SOLID WIRE, TIN PLATED COPPER COMPRESSION SQUARE LOCK NUT FOR 1" BOLT, H.D.G. ROUND WASHER FOR 1" BOLT, 2 1/2" DIAMETER, GALVANIZED

REVISED/REVIEWED: OCTOBER 2012

REVISED/REVIEWED BY: MLR

APPROVED BY: RHS

230kV INSULATORS
CIN-39

Overhead Transmission Standards

ISSSDGNC3
INSULATOR FOR CONCRETE POLES SINGLE SUSPENSION, DOUBLE GRIP, NO GUY, 230KV, 3-PHASE
CONDUCTOR OPTIONS: 954A, 954S, 1590

NOTE: SEE MBA1 FOR BOLT ASSEMBLY DETAILS

DEADEND INSULATOR UPPER BOLT A LENGTH (INCHES) LOWER BOLT B LENGTH (INCHES) NOTE:

TOP 24.6 23.9

MIDDLE 27.0 26.3

BOTTOM 29.3 28.7

BOLT CALCULATIONS ASSUME A 17 INCH POLE TOP DIAMETER

REVISED/REVIEWED: OCTOBER 2012

REVISED/REVIEWED BY: MLR

APPROVED BY: RHS

230kV INSULATORS
CIN-40

Overhead Transmission Standards

ISSSDGNC3 PLATES
ISSSDGNC3 BASE NO. ITEM ID
24 26 36 56 67 72 80 CLATG 001 CLEHL 007 COBCO 028 INSSU 009 SHAAN 003 TEEDE 003 YOKPL 003

QTY
3 6 9 ft 6 6 3 3

DESCRIPTION
CLAMP, TRANSFORMER TANK GROUND, BRONZE, #6 SOL - #1 STR SOCKET-EYE CLEVIS, CLASS 52-3/5, L = 10, EYE = 3/4 THICK W/ 13/16 OPENING, H. D. G. #4 SOLID BARE COPPER CONDUCTOR, SOFT DRAWN DEADEND SILICON INSULATOR, Y-BALL COUPLING, 230KV, L = 89 INCHES, CLASS 52-3/5 SHACKLE, 3/4, 50,000#, GALVANIZED TEE, DUCTILE IRON, HOT-DIP GALVANIZED, 6" HOLE SPACING, STRENGTH = 60,000# TRIANGULAR SUSPENSION YOKE PLATE, 16 SPACING, GLAVANIZED, 15/16 HOLE DIA.

ISSSDGNC3*954A NO. ITEM ID

12 12 12 12 45 58 62 76 77 BOLMS 053 BOLMS 054 BOLMS 055 BOLMS 073 GRISA 006 LUGGR 002 NUTSL 005 WASRD 006 WASSC 002

QTY
1 1 2 2 3 3 6 12 6

DESCRIPTION
MACHINE BOLT, 7/8 X 24, SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8 X 26, SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8 X 28, SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8 X 30, SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED DOUBLE AGS UNIT FOR 954A CONDUCTOR LUG FOR 7/8" BOLT, #4 SOLID WIRE, TIN PLATED COPPER COMPRESSION SQUARE LOCK NUT FOR 7/8 INCH BOLT, HOT DIPPED GALVANIZED ROUND WASHER FOR 7/8 BOLT, 2 1/2 DIAMETER, GALVANIZED SQUARE CURVED WASHER FOR 7/8" BOLTS, GALVANIZED, 4" X 4" SIZE

ISSSDGNC3*954S NO. ITEM ID

12 12 12 12 45 58 62 76 77 BOLMS 053 BOLMS 054 BOLMS 055 BOLMS 073 GRISA 007 LUGGR 002 NUTSL 005 WASRD 006 WASSC 002

QTY
1 1 2 2 3 3 6 12 6

DESCRIPTION
MACHINE BOLT, 7/8 X 24, SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8 X 26, SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8 X 28, SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 7/8 X 30, SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED DOUBLE AGS UNIT FOR 954S CONDUCTOR LUG FOR 7/8" BOLT, #4 SOLID WIRE, TIN PLATED COPPER COMPRESSION SQUARE LOCK NUT FOR 7/8 INCH BOLT, HOT DIPPED GALVANIZED ROUND WASHER FOR 7/8 BOLT, 2 1/2 DIAMETER, GALVANIZED SQUARE CURVED WASHER FOR 7/8" BOLTS, GALVANIZED, 4" X 4" SIZE

ISSSDGNC3*1590 NO. ITEM ID

12 12 12 12 45 58 62 76 77 BOLMS 063 BOLMS 064 BOLMS 070 BOLMS 071 GRISA 008 LUGGR 003 NUTSL 006 WASRD 007 WASSC 003

QTY
1 1 2 2 3 3 6 12 6

DESCRIPTION
MACHINE BOLT, 1 X 24, SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 1 X 26, SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 1 X 28, SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED MACHINE BOLT, 1 X 30, SQUARE HEAD, GALVANIZED, WITH SQUARE NUT ATTACHED DOUBLE AGS UNIT FOR 1590 CONDUCTOR LUG FOR 1" BOLT, #4 SOLID WIRE, TIN PLATED COPPER COMPRESSION SQUARE LOCK NUT FOR 1 INCH BOLT, HOT DIPPED GALVANIZED ROUND WASHER FOR 1 BOLT, 2 1/2 DIAMETER, GALVANIZED SQUARE CURVED WASHER FOR 1" BOLTS, GALVANIZED, 4" X 4" SIZE

REVISED/REVIEWED: OCTOBER 2012

REVISED/REVIEWED BY: MLR

APPROVED BY: RHS

230kV INSULATORS
CIN-41

Overhead Transmission Standards

THIS PAGE IS INTENTIONALLY LEFT BLANK

REVISED/REVIEWED: OCTOBER 2012

REVISED/REVIEWED BY: MLR

APPROVED BY: RHS

230kV INSULATORS
CIN-42