Scribd
Upload
39 views

Lab 2

The document describes an experiment to verify voltage and current division properties using an NI-ELVIS board and assorted resistors. It provides voltage and current division formulas and procedures to construct circuits showing voltage and current division. Students are asked to build the circuits, take measurements, calculate expected outputs using the formulas, compare results, and answer questions about applying current division to another circuit and explaining any differences between measured and calculated outputs.

Uploaded by

HAMM3T
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
39 views

Lab 2

The document describes an experiment to verify voltage and current division properties using an NI-ELVIS board and assorted resistors. It provides voltage and current division formulas and procedures to construct circuits showing voltage and current division. Students are asked to build the circuits, take measurements, calculate expected outputs using the formulas, compare results, and answer questions about applying current division to another circuit and explaining any differences between measured and calculated outputs.

Uploaded by

HAMM3T
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 6

LAMAR UNIVERSITY CIRCUITS LABORATORY

EXPERIMENT 2: Voltage and Current Division


Objective: Verify the voltage and current division properties. Equipment: NI ELVIS board Assorted Resistors ( 1 K, 2.4 K, 5.6 K and 1.2 K) Theory: Voltage and Current division allow us to simplify the task of analyzing a circuit. Voltage Division allows us to calculate what fraction of the total voltage across a series string of resistors is dropped across any one resistor. For the circuit of Figure 1, Voltage Division formulas are:

V1 =

R1 VS R1 + R2

(1)

V2 =

R2 VS R1 + R2

(2)

Figure 1. Voltage Divider

1-1

Current Division allows us to calculate what fraction of the total current into a parallel string of resistors flows through any one of the resistors.

For the circuit of Figure 2, Current Division formulas are:

I1 =
I2 =

R2 IS R1 + R2
R1 IS R1 + R2

(3)

(4)

Procedure: 1. Verifying the voltage division: a) Construct the circuit as shown in Figure 1. Measure the voltages v1 and v2 by choosing R1 = 5.6 K, R2 = 1.2 K and setting the variable power supply voltage Vs = 5V. Repeat this step for R1 = R2 = 5.6 K and note down the measurements. b) Calculate the voltages V1 and V2 by using the formulas (1) and (2) in each case. c) Compare the results from steps 1a and 1b. 2. Verifying the current division: a) Construct the circuit as shown in figure 2. Measure the currents Is, I1 and I2 by choosing R1 = 2.4 K, R2 = 5.6 K and Rs=1 K . Set the variable power supply voltage at Vs=10 V. Repeat this step by using R1=R2 =2.4 K and note down the measurements. b) Calculate the currents I1 and I2 by using the formulas (3) and (4).

1-2

c) Compare the results from steps 2a and 2b. Questions for Lab Report: 1. How well did the measured outputs and calculated outputs compare? Explain any difference. 2. Can you apply current division to obtain I1 and I2 for the circuit shown in the figure below? Explain briefly.

Figure 3.

1-3

SOME EXAMPLES
VOLTAGE MEASUREMENT DETAILS OF FIG.1

1-4

CURRENT MEASUREMENT DETAILS ON FIG.2 Measuring I1 (the current thru R1) using an Ammeter ( Digital Multimeter running in Ammeter Position)

Note: The ammeter above can also be placed before the resistor R1

Measuring I2 (the current thru R1) using an Ammeter

Note: The ammeter above can also be placed before the resistor R2

1-5

Measuring the total current IS (or the supply current)

Note: The following is another alternative when measuring IS

1-6

You might also like