ATLAS STEELS SPECIALTY STEELS PRODUCT REFERENCE MANUAL SECTION 9: APPENDICES

Stainless steel grade chart

Chemical analysis (%) specied

ATLAS STEELS
METAL DISTRIBUTION

Grade

UNS No.

Si

Mn

Cr

Mo

Ni

Other

Austenitic stainless steels

253MA 301 302HQ S30815 S30100 S30430 0.05 -0.10 0.15 0.03 1.1 - 2.0 0.75 1.00 0.8 2.0 2.0 0.040 0.045 0.045 0.030 0.030 0.030 20.0 - 22.0 16.0 - 18.0 17.0 - 19.0 10.0 - 12.0 6.0 - 8.0 8.0 - 10.0 N 0.14-0.20 Ce 0.03-0.08 N 0.10 Cu 3.0-4.0

303 304

S30300 S30400

0.15 0.08

1.00 0.75

2.0 2.0

0.20 0.045

0.15 0.030

17.0 - 19.0 18.0 - 20.0

8.0 - 10.0 8.0 - 10.5 N 0.10

304L 304H 309S

S30403 S30409 S30908

0.030 0.04 - 0. 10 0.08

1.00 0.75 1.00

2.0 2.0 2.0

0.045 0.045 0.045

0.030 0.030 0.030

18.0 - 20.0 18.0 - 20.0 22.0 - 24.0

8.0 - 12.0 8.0 - 10.5 12.0 - 15.0

N 0.10 N 0.10

310

S31000

0.25

1.5

2.0

0.045

0.030

24.0 - 26.0

19.0 - 22.0

316

S31600

0.08

0.75

2.0

0.045

0.030

16.0 - 18.0

2.0 - 3.0

10.0 - 14.0

N 0.10

316L 317L

S31603 S31703

0.030 0.030

0.75 0.75

2.0 2.0

0.045 0.045

0.030 0.030

16.0 - 18.0 18.0 - 20.0

2.0 - 3.0 3.0 - 4.0

10.0 - 14.0 11.0 - 15.0

N 0.10 N 0.10

1
S9

321

S32100

0.08

0.75

2.0

0.045

0.030

17.0 - 19.0

9.0 - 12.0

N 0.10 Ti=5x(C+N) min. 0.70 max. Nb 10xC min. 1.0 1.0 max. Cu 1.0-2.0

347 904L

S34700 N08904

0.08 0.020

0.75 1.00

2.0 2.0

0.045 0.045

0.030 0.035

17.0 - 19.0 19.0 - 23.0 4.0 - 5.0

9.0 - 13.0 23.0 - 28.0

Note 1: Single values are maxima unless otherwise stated. Note 2: Hardness specication limits given are HRB = Rockwell B scale, HRC = Rockwell C scale, HB = Brinell Hardness. Note 4: Mechanical properties shown are for the commonly available form listed; properties of other forms for the grade may vary.
Printed November 2000

ATLAS STEELS SPECIALTY STEELS PRODUCT REFERENCE MANUAL SECTION 9: APPENDICES

Mechanical properties specied (Note 4) Tensile strength MPa (min.) Yield strength (0.2% offset) MPa (min.)

Grade

UNS No.

Common form

Treatment

Elongation % in 50mm (min.)

Hardness (max) (Note 2)

Austenitic stainless steels

253MA 301 302HQ S30815 S30100 S30430 Plate Sheet or coil Wire 2.5mm dia. and over Bar Plate Annealed Annealed 1/4 to full hard Annealed Lightly drawn Cold nished Condition A Annealed 515 205 40 600 515 860 - 1275 605 max. 660 max. 310 205 515 - 965 40 40 25 - 9 95 HRB 95 HRB

303 304

S30300 S30400

262 HB 92 HRB

304L 304H 309S

S30403 S30409 S30908

Plate Plate Bar

Annealed Annealed Annealed

485 515 515

170 205 205

40 40 40

88 HRB 92 HRB 95 HRB

310

S31000

Plate

Annealed

515

205

40

95 HRB

316

S31600

Plate

Annealed

515

205

40

95 HRB

316L 317L

S31603 S31703

Plate Plate

Annealed Annealed

485 515

170 205

40 40

95 HRB 95 HRB

321

S32100

Sheet

Annealed

515

205

40

95 HRB

2
S9

347 904L

S34700 N08904

Plate Plate

Annealed Annealed

515 490

205 220

40 35

92 HRB 70 - 90 NRB typical

Note 1: Single values are maxima unless otherwise stated. Note 2: Hardness specication limits given are HRB = Rockwell B scale, HRC = Rockwell C scale, HB = Brinell Hardness. Note 4: Mechanical properties shown are for the commonly available form listed; properties of other forms for the grade may vary.

Printed November 2000

ATLAS STEELS SPECIALTY STEELS PRODUCT REFERENCE MANUAL SECTION 9: APPENDICES

ASTM standard and product use A167 A240 A666 sheet, coil, strip, plate A312 A358 A409 pipe A213 A249 A269 A554 tube A276 A582 bar and shapes A313 A493 A580 wire A182 anges pressure ttings

Grade

UNS No.

A403 buttweld ttings

Austenitic stainless steels

253MA 301 302HQ S30815 S30100 S30430

303 304

S30300 S30400

Also UGIMA Also UGIMA

304L 304H 309S

S30403 S30409 S30908

310

S31000

316

S31600

Also UGIMA

316L 317L

S31603 S31703

321

S32100

347 904L

S34700 N08904

3
S9

Note 1: Single values are maxima unless otherwise stated. Note 2: Hardness specication limits given are HRB = Rockwell B scale, HRC = Rockwell C scale, HB = Brinell Hardness. Note 4: Mechanical properties shown are for the commonly available form listed; properties of other forms for the grade may vary.

Printed November 2000

ATLAS STEELS SPECIALTY STEELS PRODUCT REFERENCE MANUAL SECTION 9: APPENDICES

Grade

UNS No.

Properties and typical applications

Austenitic stainless steels

253MA 301 302HQ S30815 S30100 S30430 Excellent resistance to scaling and useful creep strength at temperatures up to 1150C. Combination of strength and ductility to withstand severe forming methods. Corrosion resistance comparable to 302. Rail cars, automotive components. Wire for severe cold heading such as the manufacture of cross recess screws. Corrosion resistance at least equivalent to type 304. Free machining grade. Domestic and mild industrial environment. Water low in chlorides. Nuts and bolts, shafts, ttings. Corrosion resistance lower than 304. Good resistance to corrosion, good for malleability and weldability. Most commonly used grade. Wine storage, laundry and kitchen products, water, food, architectural, cryogenic and high temperature applications. UGIMA 304 improved machinability bar with same properties. Corrosion resistance as for 304. Low carbon variation for heavy gauge welded sections. Corrosion resistance as for 304. High carbon gives improved high temperature strength. Excellent resistance to corrosion, particularly attack by hot sulphur compounds in oxidising gases. Sulphite liquors and acids such as acetic, citric, lactic and nitric. Welding wire for joining dissimilar steels. Excellent corrosion resistance at normal temperatures. Good resistance to oxidisation and carburising atmospheres in high temperatures over 850C to 1100C. Welding wire for joining dissimilar steels. High corrosion resistance to the complex sulphur compounds used in pulp and paper processing. Also resists attack by marine and corrosive industrial atmospheres. Suitable for mild seacoast atmosphere, pulp and paper, heat exchangers, propeller shafts, dying equipment. UGIMA 316 improved machinability bar, with same properties. Corrosion resistance as for 316. Low carbon variation, suitable for heavy gauge welding. Improved corrosion resistance over type 316. Often successfully applied where type 316 has given only moderate performance. Applications such as acetic acid distillation, pulp and paper machinery, ink and dying processes. 317L is a variation of 317 suitable for heavy gauge welding. Excellent corrosion resistance, equivalent to 304 in the annealed condition and superior if the application involves service in 425C-870C range. Typical applications include expansion joints, furnace parts, aerospace and power industries, heat exchangers and steam generators. This grade is resistant to chromium carbide precipitation. Most commonly found as a consumable for welding 321. Super austenitic grade with very high corrosion resistance, especially to strong acids and chlorides. Frequently used in sulphuric acid service.

303 304

S30300 S30400

304L 304H 309S

S30403 S30409 S30908

310

S31000

316

S31600

316L 317L

S31603 S31703

321

S32100

4
S9

347 904L

S34700 N08904

Note 1: Single values are maxima unless otherwise stated. Note 2: Hardness specication limits given are HRB = Rockwell B scale, HRC = Rockwell C scale, HB = Brinell Hardness. Note 3: 3CR12 generally conforms with both ASTM A240 grade S41003 and with EN 10088 Parts 1 and 2, grade 1.4003. Properties quoted are from EN 10088.2. Note 4: Mechanical properties shown are for the commonly available form listed; properties of other forms for the grade may vary.

Printed November 2000

ATLAS STEELS SPECIALTY STEELS PRODUCT REFERENCE MANUAL SECTION 9: APPENDICES

Chemical analysis (%) specied

Grade

UNS No.

Si

Mn

Cr

Mo

Ni

Other

Ferritic stainless steels

3CR12 (Note 3) 409 430 430F 434 1.4003 S40900 S43000 S43020 S43400 0.03 0.08 0.12 0.12 0.12 1.00 1.0 1.0 1.0 1.0 1.50 1.0 1.0 1.25 1.0 0.040 0.045 0.04 0.06 0.04 0.015 0.030 0.030 10.5 - 12.5 10.5 - 11.75 16.0 - 18.0 0.3 - 1.0 0.50 0.75 N 0.03 Ti 6xC min. 0.75 max.

0.15 min. 16.0 - 18.0 0.03 16.0 - 18.0 0.75 - 1.25

Ferritic/Austenitic (Duplex) stainlessFerritic/Austenitic steels (Duplex) stainless steels

2205 S31803 0.030 1.00 2.0 0.030 0.020 21.0 - 23.0 2.5 - 3.5 4.5 - 6.5 N 0.08 - 0.20

UR52N

S32520 S32550

0.030

0.80

1.50

0.035

0.020

24.0 - 26.0

3.0 4.0

5.5 - 8.0

N 0.20-0.35 Cu 0.5-2.0

Martensitic stainless steels

410 S41000 0.15 1.00 1.00 0.040 0.030 11.5 - 13.5 0.75

420

S42000

0.15 min 0.20

1.00

1.00

0.040

0.030

12.0 - 14.0

431

S43100

1.00

1.00

0.04

0.030

15.0 - 17.0

1.25 - 2.50

Precipitation hardening steel

630 S17400 0.07 1.00 1.00 0.04 0.03 15.0 - 17.5 3.0 - 5.0 Cu 3.0-5.0 Nb + Ta 0.15-0.45

Note 1: Single values are maxima unless otherwise stated. Note 2: Hardness specication limits given are HRB = Rockwell B scale, HRC = Rockwell C scale, HB = Brinell Hardness. Note 3: 3CR12 generally conforms with both ASTM A240 grade S41003 and with EN 10088 Parts 1 and 2, grade 1.4003. Properties quoted are from EN 10088.2. Note 4: Mechanical properties shown are for the commonly available form listed; properties of other forms for the grade may vary.

5
S9

Printed November 2000

ATLAS STEELS SPECIALTY STEELS PRODUCT REFERENCE MANUAL SECTION 9: APPENDICES

Mechanical properties specied (Note 4) Tensile strength MPa (min.) Yield strength (0.2% offset) MPa (min.)

Grade

UNS No.

Common form

Treatment

Elongation % in 50mm (min.)

Hardness (max) (Note 2)

Ferritic stainless steels

3CR12 (Note 3) 409 430 430F 434 1.4003 S40900 S43000 S43020 S43400 Plate Tube Sheet Bar Sheet and strip Annealed Annealed Annealed Annealed Annealed 450 - 650 380 450 550 450 280 (>6mm) 320 (6mm) 205 205 380 240 18 (>6 mm) 20 (6mm) 20 22 25 22 220 HB (12mm) 250 (>12mm) 95 HRB 89 HRB 262 HB 89 HRB

Ferritic/Austenitic (Duplex) stainless steels

2205 S31803 Plate Annealed 620 450 25 31 HRC

+ UR52N

S32520 S32550

Plate

Annealed

770

550

25

310 HRB

Martensitic stainless steels

410 S41000 Plate Annealed 450 205 20 96 HRB

420

S42000

Bar

Annealed

655 typical 860 typical

345 typical

25 typical

241 HB

431

S43100

Bar

Annealed

285 HRB

Precipitation hardening steel

630 S17400 Bar Solution treated 1105 typical 1000 typical 15 typical 38 HRC

6
S9

Note 1: Single values are maxima unless otherwise stated. Note 2: Hardness specication limits given are HRB = Rockwell B scale, HRC = Rockwell C scale, HB = Brinell Hardness. Note 3: 3CR12 generally conforms with both ASTM A240 grade S41003 and with EN 10088 Parts 1 and 2, grade 1.4003. Properties quoted are from EN 10088.2. Note 4: Mechanical properties shown are for the commonly available form listed; properties of other forms for the grade may vary.

Printed November 2000

ATLAS STEELS SPECIALTY STEELS PRODUCT REFERENCE MANUAL SECTION 9: APPENDICES

ASTM standard and product use A167 A240 A666 sheet, coil, strip, plate A312 A358 A409 pipe A213 A249 A269 A554 tube A276 A582 bar and shapes A313 A493 A580 wire A182 anges pressure ttings

Grade

UNS No.

A403 buttweld ttings

Ferritic stainless steels

3CR12 (Note 3) 409 430 430F 434 1.4003 S40900 S43000 S43020 S43400

Ferritic/Austenitic Ferritic/Austenitic (Duplex) stainless (Duplex) steels stainless steels

2205 S31803

+ UR52N

S32520 S32550

Martensitic Martensitic stainless steels stainless steels

410 S41000

420

S42000

431

S43100

Precipitation Precipitation hardening steel hardening steel

630 S17400

Note 1: Single values are maxima unless otherwise stated. Note 2: Hardness specication limits given are HRB = Rockwell B scale, HRC = Rockwell C scale, HB = Brinell Hardness. Note 3: 3CR12 generally conforms with both ASTM A240 grade S41003 and with EN 10088 Parts 1 and 2, grade 1.4003. Properties quoted are from EN 10088.2. Note 4: Mechanical properties shown are for the commonly available form listed; properties of other forms for the grade may vary.

7
S9

Printed November 2000

ATLAS STEELS SPECIALTY STEELS PRODUCT REFERENCE MANUAL SECTION 9: APPENDICES

Grade

UNS No.

Properties and typical applications

Ferritic stainless steels

3CR12 (Note 3) 409 430 430F 434 1.4003 S40900 S43000 S43020 S43400 Useful corrosion resistance particularly in wet abrasion environments. Readily welded and formed into tanks, ues, bins, chutes, rail wagons, etc. Resists atmospheric and automotive exhaust gas corrosion. Extensively used in auto exhaust systems. Good combinations of corrosion resistance, formability and mechanical properties. Typical applications include automotive trims, element supports, cold headed fasteners, refrigerator doors. 430F is a free machining version of 430, suitable for high speed machining. Corrosion resistance is lower than 430. Molybdenum improves the pitting resistance over grade 430. Good for automotive trim components.

Ferritic/Austenitic (Duplex) stainless steels

2205 S31803 2205 microstructure is approximately 50% ferrite and 50% austenitic, which results in the steel possessing high strength and hardness, and resistance to erosion, fatigue, stress corrosion cracking and pitting and crevice corrosion. Applications in marine, chemical and petrochemical industries. Super Duplex grade exhibiting exceptional resistance to hot chlorides and sulphides with high strength. Applications in marine, chemical and petrochemical industries.

UR52N

S32520 S32550

Martensitic stainless steels

410 S41000 Resists dry atmospheres, fresh water, mild alkalines and acids, steam and hot gases. Must be hardened for maximum heat and corrosion resistance. Typical applications include cold heading, bolts, nuts and screws, pump parts and shafts, steam and gas turbine parts, mine ladder rungs. Good resistance in the hardened condition to the atmosphere. Food, fresh water and mild alkalines or acids. Higher carbon hardenable grade. Typical applications include cutlery, surgical instruments, shear blades, needle valves. Excellent resistance to a wide variety of corrosive media, approaching that of 304. High tensile and torque strength. Pump and boat shafts, nuts, bolts and marine hardware.

420

S42000

431

S43100

Precipitation hardening steel

630 S17400 Precipitation hardening (aging) treatment after machining gives high strength without distortion. Corrosion resistance similar to type 304. Pump shafts and valve spindles.

8
S9

Note 1: Single values are maxima unless otherwise stated. Note 2: Hardness specication limits given are HRB = Rockwell B scale, HRC = Rockwell C scale, HB = Brinell Hardness. Note 3: 3CR12 generally conforms with both ASTM A240 grade S41003 and with EN 10088 Parts 1 and 2, grade 1.4003. Properties quoted are from EN 10088.2. Note 4: Mechanical properties shown are for the commonly available form listed; properties of other forms for the grade may vary.

Printed November 2000