REVISED OBJECTIVE QUESTIONS & ANSWERS

1. End of steel bar sometimes painted in

various colors & color combination as 7. In towing the a/c (light) mark the
a mean of identifying different grade of correct statement.
steel.
1. All tail wheel a/c towing towards
1. Solid colors identify the alloy & strips backward
identify the carbon contents (*) 2. All nose wheel a/c towing towards
2. Strips identify the alloy & solid colors backward
identify the carbon content. 3. If steerable nose wheel a/c, locking
3. Both 1 & 2 are correct scissors are set of full swivel position (*)
4. None of the above is correct 4. None of the above is correct

2. Which gage is used to measure the 8. While starting the piston engine, which
backlash between gears type of fire extinguisher is permitted

1. Filler Gage (*) 1. Water & water based agent

2. Screw Pitch Gage
3. Fillet age 2. CO2, 516 capacity (*)
4. DTI 3. Dry chemical
4. CC14 (Halon Gas)
3. Accuracy of finished screw thread is
determined by 9. Which core material don't gives
deflection in composite
1. Screw pitch gauge (*)
2. Ring thread gauge 1. Honey comb (*)
3. Thread Gauge 2. Synthetic resin
4. Plug thread gauge 3. Foam
4. All of the above is correct
4. Highest size of drill is
10. Paralketone used on
1. No. 80 (0.0135)
2. 3/16 (0.1875) 1. Cable (*)
3. 3.75 mm (0.1475) 2. Iron
4. E (0.2500) (*) 3. Conduit
4. None
5. Schematic diagrams are used mainly
for 11. Interpretation analysis of defect in PFD
indicates by
1. A/C maintenance & repair
2. Trouble shooting 1. Extent of White staining
3. Installation of parts 2. Red marks on white surface. *
4. All of the above are correct (*) 3. Greenish yellow.
4. None of the above is correct.
6. Mark the correct statement
12. In pfd, when used fluorescent, material
1. Turboprop engine requires lengthy color of defective part & sound part is
runway than piston engine of same
power 1. Brilliant yellow – green & blue violet (*)
2. Turbojet has more weight than piston 2. Brilliant yellow – green & bright red
engine of same power 3. Bright red & blue violet
3. Turbofan required sort runway as 4. None of the above is correct
compare to turbojet (*)
4. All of the above are correct

115 CORRECT ANSWER IS MARKED * AT END

REVISED OBJECTIVE QUESTIONS & ANSWERS

13. Ata – 100 code of hydraulic power,

pneumatic, fire & engine oil is 20. If no marking of drill, identification of
drill can be measured by drill gauge
1. 36, 26, 79, 83 having
2. 29, 36, 26, 78
3. 29, 36, 26, 79 (*) 1. Fraction on right & number on left
4. 79, 36, 29, 26 2. Fraction on left & number on right (*)
3. Both 1 & 2 are correct
14. ATA –100 specification 37 indicates 4. None of the above is correct

1. Vacuum / pressure (*) 21. Diameter of rivet is

2. Water / waste
3. Pneumatic
1. 2 times of thickness of sheets
4. None of the above is correct
2. 3 times of thickness of thickest sheet (*)
15. Needle bearing is used where 3. 3 times of thickness of joint sheets
movement is 4. Equal to grip length

1. Oscillatory rather than rotary (*) 22. Extension tap is used for
2. Rotary rather than oscillatory
3. Both 1 & 2 are correct 1. Cut full threads in blind hole to bottom
4. None of the above is correct
2. Cut the thread in deep hole (*)
16. Embitterment is steel is reduced by 3. Thread cuts on long shaft
4. All of the above
1. Heating the steel at 150° - 200° C
(tempering) 23. Lift & drag depends upon
2. Increasing the carbon percentage
3. By annealing (*)
4. None of the above is correct 1. More cambered area of upper side &
less of lower side of wing.
17. Pressure of gas on acetylene welding 2. More cambered area of lower side and
is depend upon less on upper side.
3. As in 1 & Angle of attack
1. Area of welding surface
2. Type of material being welded
4. As in 3 & Speed of aircraft *
3. As the welder will want
4. None of the above is correct (*) 24. Gear rack is used for

18. Mark the correct statement regarding 1. Change rotary motion to reciprocating
Monel metal motion (*)
2. Change reciprocating motion to rotary
1. It can not hardened by heat treatment (*) motion
2. It can be hardened by heat treatment 3. Transmit motion to parallel with it
3. Either 1 & 2 are correct 4. None of the above is correct
4. None of the above is correct
25. Indication of class – b fire is
19. Mark the incorrect statement
1. Red (*)
1. Ultrasonic inspection _______ Piezo-
2. Yellow
electric effect (Radiography)
3. Green
2. MPI ________ skin effect (Ultrasonic) (*)
4. Brown
3. Eddy current _____ current acceptance
4. PFD _________ capillary action

CORRECT ANSWER IS MARKED * AT END 116

 REVISED OBJECTIVE QUESTIONS & ANSWERS

26. Color of extruded bar of aluminum 33. Cyaniding of low carbon is quenched in
alloy in 5 inches is
1. Oil
1. Red marking near the end of each 2. Brine
length 3. Water
2. Blue marking near the end of each 4. Both 1 & 2 (all) are correct (*)
length
3. Stamp of blue & white color 34. How long piece of steel is left in a
4. None of the above is correct furnace for soaking
27. What size of the hole should be bored
1. For long enough to ensure a good even
before cutting a 2.5" internal acme
heat throughout (*)
thread having 3 thread per inch
2. For 2 hours for per cubic inch of piece
1. 2.5" 3. One hour for each square inch of cross
2. 2.1667" (*) section area
3. 3.5" 4. Both 1 & 3 are correct
4. 2.75"
35. Scale often forms on the surface of the
28. Mark the correct statement metal & dirt blocked on it, cleaning of
scale & dirt from heat threaded part is
1. Light a/c is tied down after every flight done by
2. Light a/c is not require tied down
3. Only when strong air being to flow then 1. Steel wire brush
tie down (*) 2. Sand blasting
4. Both 1 & 3 are correct 3. Scrap
4. All of the above is correct (*)
29. Dis-integrator is used to
36. In Rockwell hardness testing.
1. Making hole in conductive metal
2. Making hole in non-conductive job 1. Softer the piece of metal, the deeper will
3. Making hole clearly & fairly be the impression under given load
4. Both 1 & 3 are correct (*)
2. The hardness is indicated on a dial gage
30. Transferred metal by chemical action graduated in the B & C scale
over a surface for 3. For non-ferrous metal, the steel ball
should be used & hardness no read on
1. Provide corrosion resistance surface B scale
2. Provide base for further plating 4. All the above are correct (*)
3. Forward up
4. All the above (*) 37. Flame heating is done for
31. For commercial annealing, cooling is
done in 1. When hardness is required only for a
limited depth of the material
1. Furnace (*) 2. For small part
2. Air 3. Both 1 & 2 are correct (*)
3. Mica 4. None of the above is correct
4. Both 1 & 2 are correct
38. Fatigue crack is detected by
32. The heat of the furnace can be
controlled or regulated by 1. Ultrasonic (*)
2. Radiography
1. Be watching the color of the furnace 3. Body current
2. Pyrometer 4. All are correct
3. Thermo meter
4. All are correct (*)

115 CORRECT ANSWER IS MARKED * AT END

REVISED OBJECTIVE QUESTIONS & ANSWERS

39. End of the steel bars are sometime

painted in various 45. Which does not passage in
electromagnetic radiation
1. Color & color combination as a means of
identifying the carbon constant 1. X-ray (*)
2. Strips identifying the alloy and solid 2. Light
color identifying the carbon 3. Infrared ray
3. Alloy identified by color, content by 4. Thermal
stripes (*)
46. Density of radioactive mean is
40. To prevent solder from running away
from the surface to be jointed. 1. Sharpness of image detail on a
radiograph
1. Flux is used (*) 2. Degree of blackening of a radio graph
2. Temperature is maintained (*)
3. Relative brightness of two adjacent area
3. Clay is commonly used to surround the
4. Both 1 & 3 are correct.
area to be jointed
4. All are collect 47. Welding decay in stainless steel is
reduced by
41. Braze welding is
1. Stainless steel containing titanium
1. Known as force welding (bronze 2. Low temperature
welding) 3. By reducing heating time
2. A welding in which base metal is not 4. All of the above is correct (*)
fuse
3. A combination of brazing & welding 48. The term used on worm gear
4. All are correct (*)
1. Throat
42. Which statement is correct 2. Throat radius
3. Throat diameter
1. Low temperature brazing is also known 4. All of the above is correct (*)
as hard soldering or silver soldering (*)
2. Silver welding has equal strength of 49. In flour sent method
material
1. If wet developer is applied, it must be
3. After silver soldering, further heat
dried (*)
treatment is required
2. If dry developer is applied, it must not be
4. Both 1 & 2 are correct dried
3. Dry for long period
43. Unit of radio active material is 4. All are wrong

1. Curies & Rutherford scale. 50. Telescoping gage

2. Roentgen. 1. Is used for inside diameter
3. Both 1 & 2 are correct. * measurement
4. None of the above is correct 2. Range from ½" to 6"
3. Range from ½" to 1"
44. Radioactive decay is measured in 4. Both 1 & 2 are correct (*)
tennis of
51. Small hole gage is used for
1. Curies 1. Measuring grooves & slots
2. Half life (*) 2. Measuring small hole
3. Both 1 & 2 are correct 3. Both 1 & 2 are correct (*)
4. None of the above is correct. 4. None of the above is correct

CORRECT ANSWER IS MARKED * AT END 116

 REVISED OBJECTIVE QUESTIONS & ANSWERS

4. All of the above is correct

52. The size of the flat cold chisel is

determined by
59. Which statement is correct
1. Width of the cutting edge (*)
2. Length of the cutting edge 1. Force is exerted on charged particle
3. Length of chisel 2. Force is applied on charged particle
4. All of the above are correct moving along the magnetic field (*)

53. Which statement is correct 60. When two sphere of same mass, one id
+ve charged & other is – ve charged,
1. Straight fluted reamer is less tendency
then new mass will
the chatter
2. Spiral type are tapered for the short 1. Change
distance back of end to and in starting 2. Unchanged (*)
(*)
3. Depend on capacity
3. Bottoming reamer have tapers end &
are used to short hole
61. If the conductor is of 4 Ω & it stretched
4. Both 1 & 2 are correct
to twice of its length, then its
54. Thread may be produced by resistance is

1. On a lathe with specially shaped cutting 1. 1Ω

tool 2. 8 Ω (*)
2. On spiral machine using rotary cutter 3. 12 Ω
3. By rolling on spiral machine using dies 4. 16 Ω
4. All of the above are correct (*)
62. A & B are big & small battery, having
55. Needle file are same emf. Internal resistance of battery
A is
1. Knurled on both side
2. Knurled on one side only 1. Less than B (*)
3. Use on slat by diameter & watch maker 2. Greater than B
4. Both 1 & 3 are correct (*) 3. Equal to B
4. Unaffected
56. Hook spanner is used on
63. Which statement is correct
1. Round nut having series of notches or
slots cuts on its side (*) 1. Battery terminal voltage is equal to
2. Hexagonal nut with slots battery emf
2. Battery terminal voltage is less than
3. ??? nut with slots
battery emf (*)
4. All of the above are correct
3. Battery terminal voltage is more than
57. Meshing gear have same battery emf
4. Depends on direction of current flow
1. Teeth (*)
2. Pitch number of some size 64. In a sport welding a typical defect is
3. Dedendum 1. Porosity
4. All of the above are correct 2. Crack
3. Irregular shape
58. Vernier scale is used on 4. Both 2 & 3 are correct (*)

1. Microscope (*) 65. In oxyacetylene welding while shutting

2. Boroscope off the flame
3. Spheroscope
1. Oxygen is shut out first

115 CORRECT ANSWER IS MARKED * AT END

REVISED OBJECTIVE QUESTIONS & ANSWERS

2. Acetylene is shut off first (*) 3. Joins the two parts in the same plane by
3. Both are shut off simultaneously overlapping
4. Both 1 & 2 are correct

66. Oxyacetylene flame with equal volume

of oxygen & acetylene gives the types 73. Radiography NDT test
of flame as shown
1. Low wave length & high penetration(*)
1. Carbonizing 2. High wave length & low penetration
2. Oxidizing 3. Invisible ray
3. Neutral (*) 4. Both 1 & 3 are correct
4. There is no such flame
74. To obtain clean & good weld
67. The silver solder metal melts at
1. Weld may be filled evenly & slowly
2. Filed with solder & brazing metal
1. 200 – 400 degree cent
3. None of the above is correct (*)
2. 300 – 600 degree cent (*)
3. 1000 – 2000 degree cent 75. The brazing the flame to be used is
4. 850 – 1200 degree cent
1. Neutral flame (*)
68. Synthetic thermoplastic 2. Oxidizing flame
3. Slightly carbonizing
1. When heated becomes soft 4. Any flame
2. When heated becomes hard
3. When cools become hard 76. Rockwell hardness tester
4. Both 1 & 3 are correct (*)
1. Measures resistance to penetration
69. A crack may be repaired by 2. Measures diameter of indention
3. Measures depth of penetration (*)
1. But welding. * 4. Both 1 & 3 are correct
2. Spot welding
3. Lap welding 77. Galvanic corrosion occurs between

1. Dissimilar metals joined without

70. In dye penetrant test, the indication
insulation between them (*)
dotted lines shown, indicates
2. Al-alloy structured assembled with steel
screw
1. Porosity (*)
3. Both 1 & 3 are correct
2. Tight crack.
3. Continuous flows. 78. Aviation snip is sued for cutting
4. All of the above.
1. Thick metal sheet
71. Corrosion on the surface of aluminum 2. Thick stainless sheet
alloy is indication on the form of 3. Heat treated al-alloy & stainless steel
sheet (*)
1. Metal bulging 4. All types of thick sheet
2. White powdery deposits (*)
79. Headless grub screws are installed by
3. Gray power deposits.
4. All of the above. 1. Allen key (*)
2. Special type of ratchet spanner
72. Fillet weld is a weld which 3. Suitable screw driver
4. Special tool
1. Joins the surfaces which are
perpendicular to each other (*)
2. Joins the two parts in the same plane by 80. An altimeter has
clamping 1. Stack of three evacuated bellows
2. Stack of two evacuated bellows

CORRECT ANSWER IS MARKED * AT END 116

 REVISED OBJECTIVE QUESTIONS & ANSWERS

3. Barometric pressure setting provision 3. Red

4. All of the above is correct (*) 4. None of the above is correct

81. In a micrometer in the main scale each 87. Select the characteristics of a good gas
cm divided into 10 equal parts & in weld
circular scale, 9 division of main scale
equals to 11 divisions of circular scale 1. The depth of penetration shall be
the least count of the micrometer is sufficient to ensure fusion of filler rod
2. The height of weld healed should be
1. 1 mm 1/8" above base metal
2. 0.01 mm 3. The weld should taper off smoothly into
3. 0.01 cm (*) base metal (*)
4. 0.0001 mm 4. These should be no oxide on the weld.
82. In a micrometer the smallest division
on main scale is 0.5 mm. The vernier 88. Which tool can be used to measure the
scale is divided into 25 division & it alignment of a rotor shaft or the place
moves one division on the main scale of rotation of disk
for complete rotation of the vernier
scale then the least count of he 1. Dial indicator (DTI) (*)
micrometer is 2. Shaft gage
3. Protector
1. 0.01 mm 4. All of the above is correct
2. 0.002 cm (*)
3. 0.01 cm 89. The measurement reading on vernier
4. 0.001 mm scale
83. Altimeter in absence of manometer
1. 1.411"
may be checks
2. 1.436"
1. Vacuum gauge 3. 1.700"
2. Vacuum chamber (*) 4. 1.456"
3. Micro manometer
4. All of the above is correct 90. Side clearance of piston ring is
measured by
84. In four digit Non Ferrous alloy index
system 2024, the first digit indicates 1. Micrometer
2. Thickness gauge (*)
1. The % of Aluminum-added 3. Depth gauge
2. The different alloy in this group 4. Dial gauge
3. Alloy group
4. Copper is the major alloying element (*) 91. What tool is generally used to set a
divider to an exact dimension
85. Why it is considered good practice to
normalize a part after welding 1. Mechanic scale (*)
2. Surface gauge
1. To relieve internal stresses developed 3. Dial indicator
within base metal (*)
4. All are correct
2. To introduce a slight amount of carbon
to improve the surface hardness of the
weld 92. Which statement is correct regarding
3. To remove the surface scales formed tie-down of small a/c
during welding 1. Manila rope has a tendency to stretch
4. All of the above is correct when it gets wet
86. The color of 100 LL fuel is 2. Nylon or Dacron rope is preferred to
manila rope (*)
1. Blue (*) 3. The a/c should be headed down wind in
2. Green order to eliminate or minimize wing lift

115 CORRECT ANSWER IS MARKED * AT END

REVISED OBJECTIVE QUESTIONS & ANSWERS

4. Leave the nose wheel or tail wheel 4. As in (3) & bottoming tap is used to cut
unlocked thread at bottom.

93. Flow of aviation fuel which passes 99. Which maintenance record entry best
greater antiknock quality than 100 describe the action taken by FAR when
octane, classified a 0.125" dent in a straight section o9f
½" Al-alloy tubing is found
1. According to the multiplies of lead
2. By reference to normal Heptanes 1. Dent is acceptable limit & repair not
necessary
3. By performance number (*)
2. Dented section removed & replaced with
4. None of the above is correct identical new tubing flared 45.
3. Dent removed by drawing appropriate
94. A primary cause of intergranular
size bullet through the tubing (*)
corrosion is
4. Deferred to maintenance check.
1. Improper heat treatment (*) 100.EMF is produced in generator by
2. Dissimilar metal contact
1. Lenz's Law
3. Improper application of heat 2. Electromagnetic Induction (*)
4. None of the above is correct 3. Right Hand Fleming Rule
4. None of the above is correct
95. Corrosion caused by galvanic action is
result of 101.AN coupling used in Aluminum tube ½
inch diameter is
1. Excessive anodization
1. AN 818-5
2. Contact of two unlike metals (*)
2. AN 818-2
3. Excessive etching 3. AN 818-8 (*)
4. All of the above is correct 4. None of the above.

96. The internal surface of sealed 102.Roller bearing take more radial load
structural steel tubing is best protected than ball bearing of same size because
against corrosion by 1. Larger contact area (*)
2. High rotation speed.
1. A coating of hot linseed oil (*)
3. Low rotation speed.
2. Evacuation of tubing before sealing
3. A coating of Zn – chromate primer 103.In brinell hardness testing, the
4. None of the above is correct thickness of material should not be
less than
97. One way to obtain increased resistance 1. 5 times diameter of the ball.
to stress corrosion is obtained by
2. 10 times diameter of the ball. *
1. Releasing compressive stress on metal 3. 20 times diameter of the ball.
2. Creating compressive stress on metal. * 4. 50 times diameter of the ball.
3. Producing non-uniform deformation 104.Which statement is correct
while cold working
4. All are correct 1. Swg 0 is small
2. Swg 14 is thicker than swg 18 (*)
98. Which statement is correct regarding 3. Swg 14 is smaller than swg 18
hand tap 4. None of the above is correct
105.Bottle jack is used.
1. Taper, plug, bottoming
2. As in (1) & bottoming tap is used to cut 1. To raise one wheel to remove brake unit
thread at bottom (*) 2. To raise single wheel
3. Plug, taper & bottoming.

CORRECT ANSWER IS MARKED * AT END 116

 REVISED OBJECTIVE QUESTIONS & ANSWERS

3. To raise single wheel to remove one 113.MODAM (Modulator – Demodulator)

brake unit used is
4. All are correct (*)
1. A part of CPU
2. A software
3. Input / output peripheral (*)
4. Operating system

106.Liquid penetrant test is carried out in

1. Porous plastic
2. Nonferrous metal (*)
3. Unpainted cleaned wood 114. When jacking the aircraft
4. Any one or all of the above are correct
1. Aircraft nose put to the wind.
107.Which statement is correct 2. Select hard & smooth surface.
1. Tank inserted into handle is knows as 3. Both 1 & 2 are correct.(*)
safe edge 4. None of the above is correct
2. When filling is done, use lubricant
3. Blade is made of steel & is not heat
115.When defuelling is done on swept back
treated
wing a/c. best precaution is
4. None of the above is correct (*)

108.Ohm's Law is 1. Outboard tank drain first (*)

2. Fuselage tank drain first
1. I∝V 3. Inboard tank drain first
2. V ∝ I (*) 4. All tank drained together
3. I∝R
4. V∝R 116.When a/c fuelling with pressure
fuelling, precaution taken
109.Flux used in soldering is
1. Chemically clean the metal by removing 1. Fuel nozzle pressure kept minimum to
oxide film (*) the fuel filter
2. Increase strength. 2. Pressure should be adequate or correct
3. Make strong joint. setting (*)
3. Electric s/w on to indicate the fuel
110.Edge distance is quantity on gauge
4. Fuel nozzle inserted before grounding
1. 2 times the shank diameter (*)
2. 2 times the sheet thickness
3. 2 times of head diameter 117.Negative plate of Ni-cd battery is of
4. None of the above is correct
1. Pure cadmium (*)
111. Which statement is correct regarding 2. Nickel hydroxide
Air speed indicator (ASI). 3. Cadmium hydroxide
1. Pitot pressure is given inside capsule. 4. None of the above is correct
2. Static pressure is given outside the
118.Electrolyte used in lead acid battery
capsule.
3. Measure differential pressure. 1. KOH
4. All are the correct (*)
2. Dilute H2SO4 (*)
112.Which one is input device 3. Concentrated H2SO4
4. None of the above is correct
1. Keyboard
2. Mouse 119.Transistor used as
3. Telephone line
4. All are the correct (*)
1. Voltage Regulator / Doublers.
2. Rectifier

115 CORRECT ANSWER IS MARKED * AT END

REVISED OBJECTIVE QUESTIONS & ANSWERS

3. Amplifier (*)
4. All the Correct 127.Mark the correct statement

120.Convert 37 decimal into binary 1. Detection w4elds in thicker material

UFD is best
1. 100101 (*) 2. X-ray best for welds in sheets
2. 111111 3. Both 1 & 2 are correct (*)
3. 101010 4. All of the above is correct
4. 110110

121.How will you remove the screw 128.When flying along magnetic equator,
dip will be
1. By welding
2. Drill the head (*) 1. Increased
3. Both 1 & 2 are correct 2. Remain unchanged (*)
4. None of the above is correct 3. Decreased
4. Depends upon direction of flight
122.Bevel gear is used to
129.Identification of alloy is made of by
1. Transmit single load
2. Transmit heavy load 1. Alloy identified by color, content by
stripes (*)
3. Transmit motion at on angle to (*)
4. Transmit motion between two parallel 2. Alloy by stripes & content by color.
shaft 3. As in 2 and number.
4. None of the above is correct.
123.After cyaniding quenching is done in
130.Heat treated parts having bake-dirt &
1. Brine scale can be cleaned
2. Water
3. Oil 1. Wire brush
4. Both 1 & 3 are correct (*) 2. Scraping
3. Sand blasting
124.To stop solder from flowing normally 4. None of the above is correct (*)
1. Clay is used 131.Pre & past treatment of cad-plating of
2. A flux is used (*) ferrous part depends on
3. Metal boundary is used.
4. None of the above is correct. 1. Strength of part
2. Surface hardening & hard spots
125.Hard soldering (silver soldering is low 3. Corrosion resistance
temperature brazing) 4. All of the above is correct (*)

1. Is done at low temperature brazing 132.The soaking time varies as

2. Produces strength equal to parent metal
3. Both 1 & 2 are correct (*) 1. Till alloy uniformly heated
4. None of the above is correct 2. 2 hrs / unit volume
3. 1 hr / unit cross section area
126.Flame is used to heat metal during heat 4. None of the above is correct (*)
treatment for
133.Vernier scale is also used in
1. Small parts
2. Where furnace is not available 1. Microscope & spectrometer
3. Heat treatment requirement is not very 2. Sextant & spectrometer
exacting 3. Both 1 & 2 are correct
4. Large parts & where a particular area is 4. None of the above is correct (*)
to be heated (*)

CORRECT ANSWER IS MARKED * AT END 116

 REVISED OBJECTIVE QUESTIONS & ANSWERS

134.In brazing 2. Resistance

3. Inductance
1. Post heat treatment may be carried to 4. All of the above is correct
relieve stresses (*)
2. Post heat treatment may not be carried 141.Which of the following is used as
to relieve stresses voltage regulator device
3. As 1 & 2 are in correct
1. Carbon pile voltage regulator
2. Magnetic amplifier regulator
3. Transistor regulator
4. All are correct (*)

135.Pre-pregs material is 142.Range of ammeter can be increased by

1. Eleminate manual mixing & weighing 1. Connecting high resistance in parallel

2. Must be stored in freeze. 2. Connecting high resistance in series
3. Also made in unidirectional 3. Connecting low resistance in parallel (*)
4. All of the above is correct (*) 4. Connecting low resistance in series

136.Which statement is correct 143.Ampere meter has

1. Boron fibre is made by depositing boron 1. Low resistance in series

2. Tungsten & ceramic fibre in high heat 2. High resistance in series
application 3. Low resistance in parallel (*)
3. Ceramic used in heat application,
dissipating heat slowly (*) 144.Transistor is biased
4. Both 1 & 2 are correct
1. Base & emitter forward biased.
137.Disbond & water in honeycomb & 2. Base & emitter reverse biased.
impect damage is detected by 3. Collector is reversed biased.
4. 1 & 3 are correct. *
1. Laser holography (*)
2. Ultrasonic
145.In tetrode, the screen grid is
3. Visual inspection
4. None of the above is correct
1. Always at positive potential & the
voltage is less than plate voltage (*)
138.In NPN transistor, arrow heat indicates
2. At negative potential & the voltage is
1. Hole flow (*) less than plate voltage
2. Electron flow 3. Voltage is more than plate voltage
3. Minority carrier flow from emitter to base 4. None of the above is correct
4. Majority carrier flow from emitter to base
146.In square threads
139.Which statement is correct
1. Width, height & length are same
1. Weld in thick material can not be 2. Difficult to machine
detected by ultrasonic 3. More strength
2. Weld in thin material can be detected by 4. All are correct (*)
X-ray (*)
3. Always detected by dye penetrant 147.In ATA-100 systems, 36 represents
4. All above are correct
1. Hydraulic system.
140.The opposition offered in AC circuit are
called 2. Oxygen system.
3. Pneumatic system. (*)
1. Impedance. * 4. Landing gear system.

115 CORRECT ANSWER IS MARKED * AT END

REVISED OBJECTIVE QUESTIONS & ANSWERS

3. Flux is used
148.Which of the statement is correct 4. All of the above is correct (*)
regarding bearing
155.The thickness of the conducting & non-
1. If corrosion is found on the outer conducting coating in ferrous metal
surface, it should be rejected can be measured by,
2. Bearing must be inspected periodically
at least once in a year (*) 1. Varnier coliper
2. Varnier micrometer
3. Shielded bearing is used be inspected
3. Ultrasonic
for corrosion
4. Eddy current method (*)
4. Both 2 & 3 are correct
156.To measure the thickness of the hollow
tubular member normally done by

1. Destructive method
149.The diameter of the aluminium sheet 2. Eddy current method
increase 3. Ultrasonic method (*)
4. None of the above is correct
1. As the gauge no increase
2. As the gauge no decrease (*) 157.A combination set is used as
3. Remain constant
4. Varies from gauge to gauge 1. Dipth, gauge, tri-square, scriber (*)
2. Protractor, scriber, trisquare
150.Piezo electricity is produced 3. Center heat, protractor, scriber
4. None of the above is correct
1. By the vibration of ceramic
2. By the vibration of quartz, Rochelle salt 158.Mark the correct statement regarding
& ceramic (*) the hardness tester
3. Sound waves have no connection with
this 1. Brinell system uses diamond point
4. All are wrong 2. Vikers uses round ball
3. Above are correct
151.Titanium can be identified by 4. None of the above is correct (*)
1. Spark test (used for various metal & 159.In nickel cadmium battery
some time from ?
2. Moisturing & scratching with a pencil 1. During discharging, the current flows
3. Chemical test the negative pole to positive plate &
4. Both 1 & 2 are correct (*) oxygen atoms are driven out from the
positive plate (*)
152.The heat resistance resin is 2. Electrical leakage is measured by
millimeter between cell & casting
1. Epoxy (cyclo eliphatic resin) (*) 3. Both 1 & 2 are correct
2. Polyester
3. Thermosetting plastic 160.Hydrogen is given off during
4. Thermoplastic
1. All stages of LAB servicing
153.For maximum ductility, elongation & 2. Over charging of Ni-cd (*)
impact resistance of Mg-alloy is 3. Both 1 & 2 are correct
4. None of the above are correct
1. Solution heat treatment (*)
2. Casted 161.Dies are used to cut
3. Precipitation heat treatment
4. Both 1 & 3 are correct 1. Internal threads of a nut
2. External threads of a nut (*)
154.Precaution in Al, welding
162.In a capacitor
1. Neutral flame is used
2. Preheating is needed

CORRECT ANSWER IS MARKED * AT END 116

 REVISED OBJECTIVE QUESTIONS & ANSWERS

1. Capacity depends on separation of 169.Which is the correct statement

plates & measured in farade regarding heat treatment of Al-alloy
2. Capacity depends on area of plates &
measured in farade 1. Longer soaking time & lower cooling
3. Capacity depends on nature of dielectric rate result in greater softening (*)
material 2. Longer soaking time & higher cooling
4. All of the above is correct (*) rate result in greater softening
3. Soaking time should be minimum
163.Relation between volt, ampere & weber 4. None of the above is correct
is given by
170.If a magnet is dropped through a
1. Amp / volt = weber
2 current carrying coil, it will fall with
2. Amp × volt = weber
3. Volt / amp = weber 1. Uniform acceleration equal to – g
4. None of the above is correct (*) 2. Uniform acceleration less than – g
3. Non – uniform acceleration more than –
164.Mooring is the process in which g
4. Non uniform acceleration less than – g
1. Head of the a/c is in prevailing wind (*)
whenever possible
2. Choke all wheels fore & aft 171.Type of heat treatment of component
3. Tie down the point on aircraft depends on
4. All of the above is correct (*)
1. Proper used
165.Which statement is correct relating to 2. Composition of alloying element (*)
swaging 3. Cold work is done
4. All of the above is correct
1. If the diameter of fitting is too large, it
has been over swaged 172.In annealing, greater softening can be
2. If the diameter of fitting is too small, it achieved, if
has been under swaged
3. If the diameter of fitting is too small, it 1. Cooling rate is very low, & it is cold in
has been over swaged & cable fitting furnace
must be rejected (*) 2. Heating just above the upper critical
4. None of the above is correct point
3. Both 1 & 2 are correct (*)
166.How will you convert a galvanometer in 4. None of the above are correct
voltmeter
173.Transfer metal from one object to
1. By connecting a high resistance in another by chemical & electrical means
series with galvanometer (*) is done to

167.Zener diode 1. Protect base metal against corrosion &

wear
1. Has high forward voltage rating 2. Increase the dimension of a part
2. Has negative resistance 3. Protect base metal against reaction
3. Has a sharp breakdown of low reverse 4. All of the above is correct (*)
voltage (*)
4. Used as amplifier 174.The circular pitch (p) of a gear is

168.In a dye penetrant test before applying 1. Point where the pitch circle of two
developer, what shall be done meshing gears touch
2. Diameter of pitch circle
1. Dye should be completely flushed out 3. Thread per inch of pitch circle
2. Only excessive dye should be removed 4. None of the above is correct (distance
3. The rinsing operation is completely from the one tooth to the center of next
carried out consecutive tooth measured on the pitch
4. Both 2 & 3 are correct (*) circle) (*)

115 CORRECT ANSWER IS MARKED * AT END

REVISED OBJECTIVE QUESTIONS & ANSWERS

175.Corrosion on Al-alloy is visible in the 1. Eddy current

form of 2. Dye penetrant
3. Ultrasonic (*)
1. Powdery form (white) (*)
2. Grey spot 183.Heat, treatment of Non Ferrous Alloy is
3. Pitting carried out by
4. Shining spark around the sport
1. Solution heat treatment
176.The hook spanner is used for 2. Solution & precipitation T
3. Age hardening
1. Round nut having slot at internal (*) 4. All of the above is correct (*)
2. Square nut having slot at internal
3. Hexagonal nut having slot at internal 184.To change the fire in case of only one
4. All of the above is correct tire, the jack should be used

177.Aviation snips are used for cutting 1. To just clear the tire from ground
2. Hydraulic jack (single base jack)
1. Steel sheets 3. Chockes used with remaining wheel
2. Al-sheets (Heat Treated) (*) 4. All of the above is correct (*)
3. Hard material
4. Soft material 185.Mark the correct statement

178.The sensitivity of voltmeter is 1. The diametrical pitch & pitch diameter in

expressed in a spur gear are same
2. If the diametrical pitch (DP) is given, you
1. Ohm can find out the addendum (*)
2. Watt 3. If we divide DP by PD, we can get size
3. Emf of teeth
4. 1/Amperes (*) 4. If the DP is given, you can not find out
the addendum
179.In inspection of bolt holes for pits &
cracks is carried out 186.A charge is moving along magnetic
lines of force
1. Before starting reaming
2. After finishing reaming 1. If force will always act
3. Before & after starting reaming (*) 2. No force will act (*)
4. Done 3. May act or may not act
4. None of the above is correct
180.In coolers or radiators where operating
temperature is high soldering is not 187.Weld decay can be prevented by
done but
1. Presence of titanium & niobium
1. Soldering can be done with approved 2. Quick heating
flux 3. Low temperature (*)
2. Inert gas welding 4. All of the above is correct
3. Seam welding (*)
4. Spot welding 188.The size of the cold chisel is
determined by
181.The function of flux in brazing
operation is to 1. Length of cutting edge
2. Weight
1. Minimize oxidation (*) 3. Width of cutting edge (*)
2. To break the surface tension of filling 4. None of the above is correct
material
3. To flow filler material all round 189.The term associated with worm gear is

182.Cracks in thick material welding can be 1. Throat

checked by 2. Throat radius
3. Pitch

CORRECT ANSWER IS MARKED * AT END 116

 REVISED OBJECTIVE QUESTIONS & ANSWERS

4. Both 1 & 2 are correct 2. Releave internal stress

3. Both 1 & 2 are correct (*)
190.Temperature of work in a furnace can 4. None of these
be measured by
198.The given tool is used for
1. Thermistor
2. Pyrometer 1. Counter sinking
3. Color of work 2. Counter boring
4. Thermocouple 3. Drilling
4. Any one of the above
191.For reaming holes should be under
size 199.Aviation ship is used for cutting:

1. About 0.003" to 0.007" (*) 1. Heat treated Al-alloy & stainless steel (*)
2. About 0.007" to 0.010" 2. Cu & its alloy
3. Not necessary 3. Any soft metal
4. None of these 4. All the above

192.Convert 29 into binary system 200.This micrometer reading is showing:

1. 111012 (*) 1. Positive zero error

2. 101112 2. Negative zero error
3. No error
3. 110112 4. None of these
4. None of these
201.The given reading shown
193.The radiographic inspection
1. Positive zero error
1. Low wave length signal travel with 2. Negative zero error
velocity of light (*) 3. No error
2. High wave length signal travel with 4. None of these
velocity of light
202.In silver soldering the temperature
194.In ATA 100 systems marking on the ranges between
cable as per

1. Prefix & strefix

1. 200°C – 400°C
2. Prefix & suffix (*) 2. 400°C – 600°C
3. Number & letter 3. 505°C – 805°C (*)
4. 800°C - 1000°C
195.In an alto meter if there is absence of
barometer is pressure, the pitot line is 203.The ASI instrument consists of
checked by
1. One capsule
1. Vacuum chamber (*) 2. Two set of capsules
2. Micrometer 3. Three set of aneroid capsules
3. Vacuum Gauge 4. There is no aneroid used is A.S.I. (*)
196.In pitot static system the static vent to 204.Hydrogen gas emits in the battery
of the flat plate tube any where in the during servicing
a/c structure to prevent
1. During the process of charging
1. Position error (*) 2. Is Ni-cd battery when charging is
2. Instrument error completed (*)
3. Protection against ice formation 3. When battery is over charged
4. Both 1 & 3 are correct 4. When connection on their terminal is
versed
197.The purpose of annealing is to
205.A screw having no head flush with the
1. Soften the metal structure can be turned by

115 CORRECT ANSWER IS MARKED * AT END

REVISED OBJECTIVE QUESTIONS & ANSWERS

1. Allean key (*) 1. After welding remove the excess metal

2. Screw extractor with file
3. Simple screw driver 2. The filler material should be properly
4. Both 1 if have hex grove head & 2 filled & evenly spaced
3. Fill the gap with Cu of brass
206.As per figure it is 4. All are wrong (*)

1. Sector gear 213.The thermo-plastic material can be

2. As a & when used with external gear – it
gives the intermittent rotary motion 1. Harden after cooling & soften after
3. Spur gear having few teeth broken heating
4. Both 1 & 2 are correct 2. Harden after cooling but can not be
soften after heating
207.In oxyacetylene welding to extinguish 3. Used for making wind shield
the flame it is good practice to 4. Both 1 & 3 are correct (*)

1. First close oxygen & then acetylene 214.Mg-alloy has no more used in a/c
regulator because
2. First close acetylene & then oxygen
regulator (*) 1. Suspectable to corrosion
3. Close oxygen & acetylene regulators at 2. Chances of cracking
a time 3. Highly resistance to corrosion
4. None of these 4. Both 1 & 2 are correct (*)

208.For welding cracks which type of joints 215.Rockwell hardness test is carried on
should be preferred specimen to:

1. Butt joining (*) 1. Measure depth

2. Lap joining 2. Measure resistance to penetration
3. Edge joining 3. Both 1 & 2 are correct (*)
4. None of these 4. Measure the diameter of impression

209.In brazing which type of flame is used 216.In oxyacetylene, the amount of oxygen
& acetylene gases are in equal
1. Carburizing proportion, as indicated in figure, is
2. Neutral (*) the:
3. Oxidizing
4. Any one can be used 1. Neutral flame
2. Oxidizing flame
210.The given tool is used for making spot 3. Reducing flame
facing to seal the washer, nut bolt heat 4. No flame will be – produced in this
is manner

1. Counter sink 217.Triode value consists of

2. Counter bore (*)
3. Reamer 1. Heater, cathode, plate & meshing wire
4. Any one of them control (gird) between plate cathode (*)
2. Heater, cathode & plate
211.The extended round portion which is 3. Heater, cathode, control grid, screen,
indicated by letter 'A' in the above grid & plate
figure is known as 4. Heater, cathode, control grid, screen
suppressor grid & plate
1. Pilot
2. Straightner 218.For converting galvanometer into
3. Guide voltmeter connect
4. All the above are wrong
1. High resistance wire in series with meter
212.For making neat & clean welding for increase range (*)

CORRECT ANSWER IS MARKED * AT END 116

 REVISED OBJECTIVE QUESTIONS & ANSWERS

2. Low resistance wire in series with meter 226.For changing the direction from linear
3. High resistance wire in parallel with to reciprocating motion
meter
4. Low resistance wire in parallel with 1. Rack is used with another spur gear (*)
meter 2. Rack is used with another rack
3. Sector gear is used with external gear
219.Inductance depends on 4. Both 1 & 3 are correct

1. No. of turns of the coil 227.Elastic stop jut should not be used
2. Core material of the coil where
3. Cross – sectional area
4. All the above are correct (*) 1. Temperature is very low
2. Temperature is higher than 250°F (*)
220.Transformer is an electrical device with 3. Vibration is very high
is used
228.Step up transformers are characterized
1. For carrying high voltage to long by
distance (*)
2. In radio set 1. High voltage & low current in secondary
3. Both 1 & 2 are correct (*)
4. None of these 2. High current & low voltage in secondary
3. High current & low voltage in primary
221.In silicon control rectifier, there is 4. High voltage & low current in primary

1. Three junction & 3 terminal (*) 229.Inductive reactance

2. Two terminals are forward blased & two
are reversed blased 1. Directly proportional to the frequency of
3. Four junction inductance (*)
4. None of these 2. Inversely proportional to the frequency
of inductance
222.This figure indicates
230.The amount of electricity a capacitor
1. Delta connection alternator can store is increased
2. Three phase alternator
3. Wire connection alternator 1. Decreasing the area of the plate
4. Both 1 & 2 are correct 2. Decreasing the distance between the
plates (*)
223.The given figure indicating 3. Increasing the distance between the
plates
1. Porosity 4. Selecting the low value of dielectric
2. Pitting constant
3. Tight crack
4. Partially welded lap or tight crack 231.Main memory unit of computer

224.The drill size diameter can be classified 1. Stores bulk of data & instructions (*)
satisfactory 2. Stores small amount of data &
instructions
1. 1 to 80 3. Performs air thematic
2. A to Z 4. Supervise the working of all the units.
3. Both 1 & 2 are correct (*)
4. None of the above 232.The capability of the computer system
to take logical decisions helps it in
225.Coating of Al-alloy by a layer of pure Al
is called 1. Making faster calculations (*)
2. Storing huge amount of data
1. Alclad or pureclad (*) 3. Decision making
2. Alodizing 4. None of these
3. Anodizing
4. All are wrong

115 CORRECT ANSWER IS MARKED * AT END

REVISED OBJECTIVE QUESTIONS & ANSWERS

233.The unit of computer performing 3. Using a hole finder

calculations is 4. All the above are correct (*)

1. Input unit 241.A, B & C of the turnbuckle assembly

2. Memory indicates
3. Output unit
4. ALU (Arithmetic Logic Unit) (*) 1. Cable eye, battle abdpin eye
respectively
234.The basic arithmetic operation 2. Fork, barrel & fork respectively
performed by a computer is 3. Cable eye, thimble & fork respectively
4. Fork, body & pin respectively
1. Addition (*)
2. Subtraction 242.Tapping screws shown in the sketch A,
3. Multiplication B & C are
4. Division
1. Counter sunk oval, truss & Philips
235.A finite sequence of steps needed to 2. Counter sunk oval, round head & Philips
solve a problem is called 3. Counter sunk, round & slotted
4. Both 1 & 2 are correct
1. A process (*)
2. A method of solution 243.Mark the correct statement, A bolt
3. An algorithm marked with a cross inside a triangle
4. A flowchart on its head is

236.In computing basic control structure 1. Al. alloy both with close tolerance
always has 2. NAS close tolerance
3. Corrosion resistant AN standard steel
1. One entry & two exit points both
2. Two entry & one exit points 4. AN steel both
3. One entry & one exit points (*)
4. Any number of entry & exit points 244.Bolt AN6-10 indicates

237.Reverse riveting is sued where 1. Length 3/16" & diameter ½"

2. Diameter 3/8" & Length 5/4" (Nickel
1. A heavier gun should be used Steel) (*)
2. The gun should be opened up
3. There is no room for revet gun 245.Purpose of heat treating titanium is
4. All the above are correct
1. Relief of stress
238.Type of Hi-shear pin shown in the 2. Hardening to improve strength
sketch is known as 3. 1 & 2 & also to provide maximum
ductility for subsequent cold working
1. Dowel pin (*) 4. All of the above are correct (*)
2. Tapped pin
3. Special cam 246.Channels, angles, T-sections can be
4. None of the above is correct made by the process known as

239.While riveting if the damage shown in 1. Rolling

the sketch takes place, it is known as 2. Extruding (*)
3. Forging
1. Damaged place due to riveting tool (*) 4. Hammering
2. Cracked head due to hard material
3. Rivet tight & plates bulged 247.For gas welding, while lighting the
4. None of the above is correct blow pipe, if flash back occurs, the
cause may be due to
240.Rivet hole can be located by
1. Regulators are not set to correct
1. Punching pilot holes pressure (*)
2. Using of a template

CORRECT ANSWER IS MARKED * AT END 116

 REVISED OBJECTIVE QUESTIONS & ANSWERS

2. Flow of gas is not ensured before

lighting takes place 1. Porosity (*)
3. Both 1 & 2 are correct & over heating 2. Lack of penetration
4. All use of spark lighter 3. Craters
4. Channeling
248.When certain natural crystal is
subjected to 255.Which treatment process of metal
produces a hard & wear resistant
1. Vibration sound beam, an altering surface area with strong & tough in
current is produced core
2. Mechanical stress, an electric field it
produced (*) 1. Case hardening (*)
3. Application of voltage, mechanical 2. Tempering
stress is produced 3. Annealing
4. All the above are correct & also in case 4. Normalizing
of vibration, the frequency of vibration
depends on the thickness of the crystal. 256.The diametrical pitch of a gear is

249.Delamination can be detected by which 1. An imaginary circle passing through the

method points at which meshing of teeth takes
place
1. Ultrasonic (*) 2. The diameter of the pitch circle
2. Eddy current 3. The number of teeth per inch of pitch
3. Dye penetrant diameter (*)
4. Magnetic Particle 4. None of the above is correct

250.Zinc chloride is the best flux to sue 257.In connection with square thread, mark
soldering the correct statement

1. Wrought iron, steel or stainless steel (*) 1. The width & depth of the thread are
2. Cast iron, nickel, lead equal to the space between threads
3. Monel metal, galvanized iron 2. It is very strong
4. All above are correct 3. Accurate machining of this thread is
difficult
251.Anneanlaing is the process that 4. All of the above are correct (*)

1. Makes the metal soft 258.While drilling a hole, of the finished

2. Relieves the internal strain hole ahs a rough surface, the cause is
3. That lowers the strength of the metal
4. Both 1 & 3 are correct (*) 1. Dull drill was used
2. The drill penetrated the work very slowly
252.T4 & W for alluminium alloy indicates & become very hot while in operation
3. The drill hole was made very rapidly
1. Solution heat treated & quenched but 4. Both 1 & 2 are correct (*)
not aged (*)
2. Only solution heat treated 259.Length of hackshaw blade is
3. Precipitation heat treated
4. Solution heat treated & artificially aged 1. Distance from the centre of one hole to
the center of the another hole of other
253.Scattered dot when viewed under ultra end (*)
violet radiation indicates 2. Total length over which teeth are
spreaded
1. Fine porosity 3. Length from one end to the other end
2. Gross porosity 4. All of the above are wrong
3. Pitting
4. Both 1 & 3 are correct (*) 260.Micrometer shadow is

254.If a damp flux is used while welding 1. Shadow of the thimble (*)
with oxy-acetylene flame, then it will 2. Shadow of he sleeve
cause 3. Shadow of the spindle

115 CORRECT ANSWER IS MARKED * AT END

REVISED OBJECTIVE QUESTIONS & ANSWERS

4. None of the above 269.Turn buckle is in safety minimum

261.Most accurate method of classifying 1. Not more than one thread is exposed
drill size is outside barrel
2. Half number of threads are inside the
1. 1/16" to 1 barrel
2. 1/64" to 11" 3. All the threads are inside the barrel
3. A to Z 4. Not more than 3 threads are exposed (*)
4. No. 80 to No. 1 (*)
270.Trammel is used
262.To ream a hole, the hole must be drilled
1. To draw large circle (*)
1. 0.001" to 0.007" undersize 2. To draw large square
2. Same size as given 3. To draw large rectangle
3. 0.003" to 0.007" undersize (*) 4. To draw large pentagon

263.Flux density is measured in tesla – 271.The line used to show an edge which is
weber/m2 = not visible is a

1. Gauss 1. Position line

2. Farad 2. Phantom line
3. Ampere 3. Hidden line (*)
4. Hennery 4. Broken line

264.Altimeter in absence of manometer 272.A drawing in which all the parts are
may be checked by brought together as an

1. Vacuum gauge (*) 1. Working drawing

2. Vacuum chamber 2. Detail drawing
3. Micromanometer 3. Assembly drawing
4. All of the above 4. Installation drawing (*)

265.Zenor diode is used September – 1994

1. As voltage regulator (*) 1. The most commonly used symbols for

2. To prevent spikes electromagnetic flow detection
3. Both 1 & 2 are correct
1. UFD
266.Binary expression is known as 2. MFD (*)
3. PFD
1. Bit (*) 4. EFD
2. Byte
3. None of the above are correct 2. In oxyacetelene welding it is better
practice while shutting off the flame
267.Base of NPN transistor is
1. Shut off oxygen first
1. N type semiconductor 2. Shut off acytelene first (*)
2. P type (*) 3. Turn off the regulator
3. N-P diode 4. Turning off simultanelously
4. P-N diode
3. The silver soldeny metal melts at
268.Bolt without any specification while
using 1. 200 – 400 degree cent
2. 500 – 850 degree cent (*)
1. Should be cleaned & degreased 3. 1000 – 1600 degree cent
thoroughly (*)
2. Should be greased on the thread 4. A crack may be repaired by
3. Should be greased thoroughly
1. Butt welding (*)

CORRECT ANSWER IS MARKED * AT END 116

 REVISED OBJECTIVE QUESTIONS & ANSWERS

2. Spot welding 1. A plate, grid & a heater

3. Lap welding 2. A plate, cathode & a heater
4. Edge welding 3. Plate, screen & a heater
4. Plate, cathode, heater & wire screen
5. Annealing is the process between the plate & cathode (*)

1. Makes a metal soft 13. Zenor diode is used

2. Relives the internal strain
3. Toughen the metal 1. To regulate voltage (*)
4. Both 1 & 2 are correct (*) 2. Controls the spikes
3. Both 1 & 3
6. T & w are the symbols utilized for heat
treatment of Al-alloy sheet indicates 14. Diode, triode & transistors

1. Solution heat treated only 1. Obey Ohm's Law

2. Solution heat treated & quenched but 2. Does not obey ohm's law (*)
not aged (*)
3. Precipitation heat treated 15. Taking all the factors into consideration
4. Solution heat treated & artificially aged the most commonly used metal as
electrical conducting
7. Rockwell hardness tester
1. Aluminium (*)
1. Measures resistance to penetration 2. Copper
2. Measures the diameter of the 3. Silver
impression 4. Iron
3. Measures depth of impression
4. Both 1 & 3 are correct (*) 16. In gear system, a driver & driven on the
shaft to get the same direction of
8. Which is true in relation to magnesium rotation
alloy
1. Bevel gear is used
1. It is most susceptible metal to corrosion 2. Internal & external gear combination is
2. It has get high resistance to corrosion used
quality & can be heat treated 3. As in (1) & no mechanical advantage is
3. It is the lightest metal used in the a/c obtained
structure 4. None of the above is correct (*)
4. Both 1 & 3 are correct (*)
17. In regular interval, to calibrate a
9. Galvanic corrosion is micrometer where you carried out

1. Dissimilar metal corrosion (*) 1. In normal environment & controlled

temperature (*)
10. Decimal 29 is equivalent to binary 2. In air conditioned room but does not
number proof
3. A room is calibrated upto 20-30 microns,
1. 11101 (*) but not air conditioned
2. 10110 4. A room is calibrated upto100-150
3. 11110 microns, & also air conditioned
4. 10101
18. To bring the sheet together to get air
11. SCR (Silicon Control Rectifier) has tight joint, we use

1. 2 terminals 1. Draw set

2. 2 terminals are forward biased & 1 2. Cleco fastener (*)
terminal are / is reverse (*) 3. Aligning camp
3. 3 terminals 4. None of the above is correct
4. None of the above
19. Choose correct statement
12. A triode consists of
1. Philips screw – driver is blunt at end (*)

115 CORRECT ANSWER IS MARKED * AT END

REVISED OBJECTIVE QUESTIONS & ANSWERS

2. Read & prince screw driver is blunt on 2. When lead acid battery gets over
end charged
3. Both are interchangeable 3. Towards the end of the charging of Ni-cd
4. All of the above is correct battery (*)
4. Both 2 & 3 are correct
20. To avoid vibrating stress in tube lines
27. The strength of the electromagnet is
1. No bend is done determined by
2. Two bend is done
3. Atleast one bend is done (*) 1. No. of turns of the coil
4. Preferably no bend is done, & if bend is 2. Strength of the magnet
done, it will be less than 45° 3. Speed of rotation of the magnet
4. All of the above (*)
21. Dzus fastener consists of
28. ½ - 13 NC – B indicates
1. Stud, washer & receptacle
2. Stud, grommet & receptacle (*) 1. Pitch diameter ½"
3. As in (2) & grommet is made of spring 2. B – external thread
4. None of the above is correct 3. 13 NC – indicates 13 TPI & have
national form
22. Air drill in aviation industry in preferred 4. All of the above is correct (*)
to electric motors drill.
29. A vernier caliper has least count 0.02
1. No other equipment is required cm & have a negative error – 0.02 mm
2. It is available in various shape, sizes, reading on main scale is 0.48 & 6th
running speed, drilling head angle (*) division of vernier scale coincide with
3. High initial cost & less maintenance main scale. The reading is
4. Both 1 & 2 are correct
1. 0.485 cm
23. Double flaring is 2. 0.488 cm
3. 0.062 mm (*)
1. Provide smooth & concentric surface 4. None of the above is correct
2. As in (1) & resistance to shearing effect
of torque 30. Counter boring & spot facing is
3. As in (2) & generally used in a/c (*)
4. As in (3) & diameter of tube is reduced. 1. Having same operation
2. Counter boring is done for nut
24. A galvanometer may be converted to a 3. Sport facing is the operation of making
voltameter by connecting flat circular surface around hole (*)
4. None of the above is correct
1. Low resistance coil in parallel with meter
2. High resistance coil in parallel with DGCA Questions
meter
3. High resistance coil in series with meter 1. Aviation snips are used on
to increase range (*)
4. Low resistance coil in series with meter 1. Heat treated Al alloy sheet & Stainless
Steel (*)
25. In ATA coding system the size & type of 2. Fibre
the electrical cables / wires in a/c are 3. Sheet Steel
given by 4. All of the above is correct

1. Prefix & suffix 2. Solder used for electrical connection

2. Side by side has the M & range
3. Numbers & Letters (*)
4. None of the above is correct 1. 100 - 200°C (*)
2. 100 - 3000°C
26. Hydrogen gas is given up
3. 300 - 6000°C
1. Entire servicing of Ni-cd battery 4. 200 - 3000°C

CORRECT ANSWER IS MARKED * AT END 116

 REVISED OBJECTIVE QUESTIONS & ANSWERS

CG within limits using a minimum

3. Helical gears used for amount of wt. (*)
3. Preferable permanent ballast
1. Transmit motion to shaft at an angle 4. Preferable temporary ballast
2. Transmit motion to shaft which is are
perpendicular together 11. Electric weighing machine
3. To carry larger loads (*)
4. None of the above is correct 1. Switched – ON before minutes
2. Switched – ON just prior to weighing so
4. The best conductor available that equipment is not heated (*)
considering all factors in a/c use is 3. As in (1) & circuit is provided to get
stabilized
1. Copper 4. All are correct
2. Alluminium (*)
3. Brass 12. Static wick is mentioned in the _______
4. Silver chapter of the maintenance manual

5. The binary equivalent of 29 is 1. 21

2. 23 (*)
1. 11101 (*) 3. 24
2. 10101 4. 32
3. 10011
4. 11111 13. Altimeter is checked by when
barometer is not available
6. An altimeter consists of
1. Micro manometer
1. Two aneroid capsules 2. Vacuum chamber (*)
2. Pressure setting knob for adjusting
barometric pressure 14. Static vents in pitot static system are
3. Three aneroid capsules located with
4. All the above are correct (*)
1. Free at air stream (*)
7. Most headless set screws are turned by 2. To eliminate ice formation
3. 1 & 2 are correct
1. Screw driver 4. Flexible
2. Philips screw driver
3. Internal screw driver 15. X-ray used in NDT inspection
4. Allen wrench (*)
1. Have short wave length high penetrating
8. SCR is power
2. Have long wave length low penetrating
1. Four junction diode power
2. Three junction diode (*)
3. Two junction forward based with one 16. To repair a crack, the join to be formed
reversed biased
4. Plate, cathode, heater & fine mesh of 1. Lap joint
wire between plate & cathode 2. Butt joint (*)
3. Bee joint
9. Doubller plate is 4. Corner joint

1. Same size 17. A transistor is

2. Double the thickness
3. Just half the thickness 1. Amply the low input signal to high output
4. None of the above is correct (*) signal (*)
2. Used as a rectifier
10. Ballast is used to balance the a/c 3. Used in transducer set
4. 1 & 2 are correct
1. Located as near as to CG
2. Is minimum weight & places as far aft or 18. Purpose of point in either straight or
as far forward as possible to bring the twisted drill

115 CORRECT ANSWER IS MARKED * AT END

REVISED OBJECTIVE QUESTIONS & ANSWERS

2. 0.001 cm
1. To provide the flow of the cutting fluid to 3. 0.09 mm
the cutting edges 4. 0.009 cm
2. For clip removal
3. To provide lip cutting edges (*) 26. The component shown as
4. All of the above
1. Flange
19. Clevis bolt is used for 2. Scupling
3. Spacer
1. Shear loads only (*) 4. 1&2
2. Tensile loads only
3. As a pin in control systems 27. Hydrogen is given off
4. 1 & 3 are correct
1. During all stages of battery servicing
20. In a capacitor the voltage rating 2. When battery is over heated in Ni-cd
decreases with increase in battery (*)
3. During charging operation of the battery
1. Dielectric strength 4. During discharging operation of the
2. Thickness of dielectric (*) battery
3. Frequency
4. Area of the plates 28. Magnesium is

21. American close tolerance nut is used 1. Susceptible is corrosion

for 2. Corrosion precisiant & light weight
3. Has tendency in crack
1. Machine surfaces 4. 1 & 3 are correct (*)
2. Heavy forged structures
3. Tight fit assemblies (*) 29. When switch 'S' is open, voltmeter
4. 2 & 3 are correct indicates 1.5 v & when closed indicates
1.35 v current is 1 amp what is the
22. The zener diode internal resistance of the battery.

1. Is used as rectified 1. ∆ Ohm

2. Is used for voltage regulation (*) 2. 0.15 Ohm (*)
3. 1.35 Ohm
23. The most accurate system for drill size 4. 1.50 Ohm
is
30. For most satisfactory plating on AGS &
1. Fraction (1/16" – 31/2") non steel materials
2. 1/64" – 11/2"
3. A to Z 1. Nickel plating
4. No. 80 to No. 1 (*) 2. Cadmium plating (*)
3. Zink plating
24. In a vernier scale, 24 division are equal 4. Galvanizing
to 25 division of vernier so 1 cm of
main scale is divided 20 equal parts, 31. Rough surface of castings & bars etc
find the least count removal, by an abrarive cutting tool is
called
1. 0.001 cm
2. 0.002 cm (*) 1. Grinding (*)
3. 0.002 mm 2. Snagging
4. 0.001 mm 3. Lapping
4. Finishing
25. In a vernier micrometer of part of main
scale is divided into 10 of scale, the 32. Replace a solid rivet with a hollow rivet
main scale has the graduations of 1 we would check for
mm find the least count.
1. Material & compression strength
1. 0.01 cm (*) 2. Material & shear strength (*)

CORRECT ANSWER IS MARKED * AT END 116

 REVISED OBJECTIVE QUESTIONS & ANSWERS

3. Heat treatment
4. Material & tensile strength 40. In case of flouruscent die penetrant
inspection, the developer used is
33. DTI indicator is
1. Dry powder
1. Eccentricity of a small levels in rotating 2. Powder suspended in volatile liquid
shafts 3. Powder suspended in water
2. To measure the dimension 4. All of the above is correct (*)
3. To check the depth of large parts
4. All of the above is correct (*) 41. Round heat rivet is

34. In hot oil & chalk methods the following 1. 430 (*)
can not be detected 2. 442
3. 462
1. Vertical cracks 4. 456
2. Horizontal cracks
3. Wavy cracks 42. Fretting corrosion effect
4. Minute flows & tightly shut cracks (*)
1. Thickness of the parts will be reduce (*)
35. The following washers are not used on 2. Parts get brittleness
the part which is exposed to air flow 3. Toughness increase
4. Fatigue strength of parts decreases
1. Plain washer
2. Special washer 43. When selecting a rivet for replacement
3. Lock washer (*) of a solid rivet, we observe for
4. 1&2
1. Dissimilar action corrosion
36. How many types of fits according to 2. Shape of head (*)
American standards 3. Length of rivet
4. None of the above is correct
1. Three
2. Six 44. Fillet welding is
3. Eight (*)
4. Four 1. Edges joined perpendicularly by (*)
2. Edges joined parallely by clambering
37. Structural screw will have 3. Edges joined keeping the plates one
over the other parallely, one being
1. Same strength of the AN bolt (*) horizontal
2. Half of strength of the AN bolt 4. Clearance done at the edge of the gear
3. Sometimes less than half of strength of teeth
the AN bolt
4. Both 2 & 3 are correct 45. American standard control cables are
made of
38. In different countries, the same rate
battery was charged which gets more 1. Molybenium steel (*)
charged 2. Cast steel
3. Stainless steel
1. 80 f, 1 hour 4. Brass
2. 80 of, 1 hour
3. 60 of, 30 minute 46. Regarding thermal runway which of the
4. 70 of, 45 minute (*) following is not correct

39. BA british unified bolts & screws can 1. Imbalancing of cells

be recognized by 2. Deep cell treatment
3. Due to constant current more chances
1. Violet dye for thermal runaway (*)
2. UNF stamping on the bolt 4. Over heating of a cell
3. Raised or recessed circles on the head
(*)
4. All of the above is correct

115 CORRECT ANSWER IS MARKED * AT END

REVISED OBJECTIVE QUESTIONS & ANSWERS

47. For any battery the charged without 2. SP

constant current conditions can be 3. ACS
found while changing. 4. MS

1. Specific gravity taken at interval of 30 54. Is fastener dimensions are specified as

min three consecutive redings should be
same 1. Diameter as 1/32 inches & length as 1/8
2. Gassing will occur (*) inches
3. Voltage stops rising 2. Diameter as 1/16 inches & length as
4. 1 & 2 are correct 1/16 inches
3. Diameter as 1/16 inches & length as 1/8
48. A 35 AH, 12 V battery is discharged inches (*)
according to the following rates which 4. Diameter as 1/16 inches & length as
will give maximum capacity? 1/100 inches

1. 10 hrs, discharge rate 55. Radio graphic inspection, which of the

2. 15 hrs, discharge rate following waves are used
3. 20 hrs, discharge rate
4. 5 hrs, discharge rate (*) 1. X-rays
2. r – rays (Gamma Rays)
49. Structural screw will have 3. Ultraviolet rays
4. 1 & 2 are correct (*)
1. Same strength of the AN Bolt (*)
2. Half of strength of the AN bolt 56. Dump fluid increases
3. Sometimes less than half of strength of
the AN bolt 1. Porosity (*)
4. Both 2 & 3 are correct 2. Lack of penetration
3. Channel low
50. Capacity in lead acid battery as 4. Clarity of formation
determine by
57. Marking is done on constant barrel
1. Density of electrolyte (*)
2. Plate area 1. To avoid miscalculations (*)
3. Internal resistance 2. More precise valued
4. No. of cells 3. To create miscalculations
4. None of the above
51. The motor with two different coils
wound on difference sence, which can 58. Black pitting & reddish brown
rotate in two direction is corrosion occurs on

1. Series 1. Corrosion resistant steel (*)

2. Shunt 2. Cast iron
3. Compound (*) 3. Magnecium
4. Differentially compound motor 4. Aluminium

52. The treatment of Magnesium, the 59. For getting high ampere hour capacity
following chemicals are used in & high terminal voltage the plate of
cells should be connected as
1. Electrolyte bath
2. Potassium dischromate, sodium 1. In series so that to get high internal
chromate & zinc chloride (*) resistance
3. Ammonium cyanide, potassium cyanide 2. In series so that to get low internal
& zinc sulphate resistance (*)
4. None of the above 3. In parallel so that to get low internal
resistance
53. Society of british aerospace has given 4. In parallel so that to get high internal
rivet standard as resistance

1. As (*) 60. The CP of bevel gear is

CORRECT ANSWER IS MARKED * AT END 116

 REVISED OBJECTIVE QUESTIONS & ANSWERS

1. Tooth per inch 1. Formed by pneumatic hammer (*)

2. The distance from the center of open 2. Manufactured head
tooth to the center of next tooth 3. Special rivet
measured on the pitch circle
3. The distance from the center of one 69. Disposable load is
tooth to the center of next tooth (*)
4. None of the above 1. Fuel that can be thrown out of a/c during
emergency conditions (*)
61. The binary expression of 296 is 2. All persons & their belongings, fuel, oil
that is used in the journey
1. 101011101 3. Empty load & variable load
2. 100101000 (*) 4. Fuel & oil which is unusable
3. 111001100
4. 110010111 70. The stretch shows

62. The number of TPI is measured by 1. Buttress thread

2. ACME thread
1. Screw pitch gauge (*) 3. V-thread
2. SWG 4. Square thread
3. Thickness gauge
4. None of the above 71. The method used in temper steel
depends upon
63. The output of an OR gate will be given
1. Type of steel
1. When all inputs are energized 2. Size of steel
2. When all the inputs are zero 3. Density of steel
3. Any one of the input is energized 4. All of the above (*)
4. 1 & 3 are correct (*)
72. The readings shown on the
64. Computer consists of instruments is

1. Printer, decoder, memory 1. 1.318"

2. Input, Output, CPU (*) 2. 1.314"
3. Input, Output, Printer 3. 2.300"
4. None of the above 4. 3.150"

65. The decimal number for 10111011101 is 73. The computer hard disks & floppy
disks are
1. 1501
2. 1500 1. Different in use
3. 1401 2. Similar but hard disk can store more
4. 1600 than floppy disk (*)
3. Similar but hard disk can store less than
66. The drawing symbol floppy disk
4. None of the above
1. Fixed capacitor
2. Variable capacitor 74. The readings shows as
3. Variable resistor
4. Fixed resistor 1. 2.500"
2. 0.250"
67. O-rings are checked for internal cracks 3. 0.275"
by 4. 0.200"

1. 4 power magnifying glass 75. Bevel gears used for

2. By rolling on inspection cone
3. By rolling on inspection dowel 1. Transmission of loads for between
4. All of the above (*) shafts to each other (*)
2. For variation of speed
68. Shop head of a rivet is 3. In speed reducers

115 CORRECT ANSWER IS MARKED * AT END

REVISED OBJECTIVE QUESTIONS & ANSWERS

4. 1 & 3 are correct 2. To increase the bonding

3. To provide flow to the molten metal
76. The component shown is 4. All of the above are correct (*)

1. Universal wrench 84. An optical instrument used to inspect

2. Spanner French the interior structure of a component is
3. Open end wrench
4. None of the above 1. Fibrescope
2. Boroscope
77. The DP in a gear indicates 3. Endoscope
4. All of the above (*)
1. Number of teeth per inch
2. Size of the gear teeth 85. The check interior surface condition of
3. Both 1 & 2 are correct (*) cylinders & surfaces, instrument used
4. None of the above is

78. Barcol tester is used for 1. Boroscope

2. Fibrescope
1. Steel 3. Endoscope or introscope
2. Al-alloy 4. All of the above are correct (*)
3. Titanium
4. As in 2 & copper (*) 86. Mark correct statement

79. Calculate the reading 1. A – radial load, B – radial load & thrust
load
1. 0.1001 2. A – thrust load, B – radial load
2. 0.250 3. A & B – thrust load
3. 0.4250 4. A & B – radial load
4. 0.200
87. Reading is
80. Identify the drawing symbols given
below 1. 0.257
2. 0.270
1. Normal C.B., Push – pull C.B., Push – 3. Two hundredths of an inch
pull C.B. 4. Three hundredths of an inch
2. Automatic C.B., Push C.B., Push – pull
C.B. 88. Radiography depends on
3. Push-pull C.B., Automatic C.B., Normal
C.B. 1. Size & shape
4. Automatic reset, push reset, push reset 2. X-ray
pull off 3. Thickness of material
4. All of the above are correct (*)
81. Memory of computer are
89. Calculate the reading
1. ROM, CPU, ALU
2. ROM, RAM, PROM (*) 1. 0.2507
3. ALC, ROM, RAM 2. 2.507
4. None of the above 3. 0.4250
4. 1.200
82. Stress corrosion occurs mainly on
90 Identify:
1. Magnesium alloys
2. Aluminium alloys 1. A & D are variable resistors & b & C are
3. Stainless steel fixed resistors
4. Both 2 & 3 are correct (*) 2. A & C are fixed resistors & b & c are
variable resistors
83. Purpose of using flux in welding in 3. A & B are fixed resistors & b & d are
variable resistors
1. To reduce oxidation 4. None of the above

CORRECT ANSWER IS MARKED * AT END 116

 REVISED OBJECTIVE QUESTIONS & ANSWERS

3. Neutral flame (*)

91. Identify: 4. Reducing flame but first the flame is
neutral & then reduced
1. Potentiometer
2. Resistor 99. Brass & bronze are welded with
3. Auto transformer
4. Iron transformer 1. Oxidizing flame (*)
2. Reducing
92. In fluorescent dye penetrant test, the 3. Neutral flame
color of the light under which the part 4. Reducing flame but first the flame is
is inspected neutral & then reduced

1. Green colour in black light 100.This tool is used for

2. Green color in white light
3. Ultra violet shining light (*) 1. For internal measurements
4. Red color in white light 2. Measuring hole diameter
3. Outside measurements
93. Rockwell tester measures 4. Both 1 & 2 are correct

1. Resistance to penetration (*) 101.In a 4 stroke engine the spark plug

2. Diameter of impression fires for every
3. Size of indentation
4. None of the above 1. 4 revolutions of crank shaft
2. 2 revolutions of crank shaft (*)
94. Cleaning of titanium surface 3. ½ revolution of crank shaft
4. 360 degree revolution of crank shaft
1. Steel, steel wool
2. Iron scrapers 102.If a wire having a resistance of 4 Ω is
3. Mild abrasive or hand polish with stretched twice of its length given its
aluminium (*)
4. None of the above 1. 1Ω
95. PN junction is used as 2. 8 Ω (*)
3. 16 Ω
1. Rectifier (*) 4. 4Ω
2. Amplifier
3. Oscillator 103.7 resistors of 20 Ω are connected
4. None of the above parallel & battery voltage is 2 volt the
ammeter reads
96. NPN transistor
1. 1/10 A
1. Flow of electrons from emitter to 2. 3/10 A
collector (*) 3. 4/10 A
2. Holes move from collector to emitter 4. 7/10 A (*)
3. Flow of electrons from base to emitter
4. Flow of electrons from emitter to base 104.Identification of titanium
97. In triode, grid 1. Spark test
2. Moistering & marking on glass
1. Controls the flow from plate to cathode 3. Acid test
(*) 4. Both 1 & 2 are correct (*)
2. Reduces space charge
3. It increases emission of electrons from 105.Inhealed metal is Annealed
cathode
4. Prevents secondary emission 1. Is soft
2. Relieved internal stress
98. Aluminium alloys are welded with 3. Low strength
4. All of the above is correct (*)
1. Oxidizing flame
2. Reducing flame

115 CORRECT ANSWER IS MARKED * AT END

REVISED OBJECTIVE QUESTIONS & ANSWERS

106.Reading of inside micrometer 3. Both will increases

4. Both will decreases (*)
1. 0.527
2. 0.425 113.The rivet head indicates the material
3. 0.475
4. 2.015 1. 2024
2. 21171
107.Identical insulated wire coils are hung 3. Monel (Nickel copper alloy)
from air so that they are racing each 4. None of the above is correct
other & supplied with same direction
A.C. 114.The abbreviation "Unix" used in
computer indicates:
1. Anti clockwise rotation
2. Both are repelled 1. A new operating system
3. Both are attracted to each other (*) 2. Operating system other than MS-DOS
4. Clockwise rotation (Microsoft Disk Operating System)
3. PC – AT computer may have "Unix"
108.Which of the following has negative co- operating system in addition of MS-
efficient of resistance DOS.
4. None of the above is correct
1. Thermistor (*)
2. Transistor 115.The most sophisticated computer is
3. Semiconductor
4. Resistor 1. Micro computer
2. First generation computer
109.In a given figure, what may be the 3. Super computer (*)
cause of fault for the installation of 4. None of the above is correct
rivet
116.Which is principal load carrying
1. Greater allowance on the formal head member in composite materials
2. Snap not regular to the head
3. Bucking bar not in position 1. Fabric (*)
4. None of the aboe is correct 2. Matrix
3. Resin
110.The type of corrosion which occurs 4. None of the above
when two making surfaces, normally at
rest with respect to one another, are 117.The size range of an allen wrench is
subject slight relative motion is know
as? 1. 3/64 to ½"
2. 1/64 to ½"
1. Stress corrosion 3. 3/64 to 1/8"
2. Fretting corrosion (*) 4. 1/64 to 1/8"
3. Crevice corrosion
4. Inter granular corrosion 118.The function nut on an a/c landing gear
requires a torque of 100 inch pounds.
111.The letter : 0 in heat treatment process To reach the nut, a 3" straight adapter
represents the following condition must be used on an 15" torque wrench.
How many inch pound will be indicated
1. Strain hardened on the torque wrench when the
2. Annealed (*) required torque of the nut is reached?
3. Solution heat treated
4. None of the above is correct 1. 100
2. 83.3 (*)
112.When an aircraft catches fire, (made of 3. 0.80
aluminium) conductivity & resistivity of 4. 115.6
aluminium respectively
119.Carbon steel is
1. Increases decreases
2. Decreases increases

CORRECT ANSWER IS MARKED * AT END 116

 REVISED OBJECTIVE QUESTIONS & ANSWERS

1. Strongly magnetic & shows slow 125.During welding, the welding torch
chemical reaction with nitric acid test should be kept
2. Non magnetic & non action with HN
3. Strongly magnetic & rapid action with 1. Into the molten metal
HNO3 test 2. Above the colten metal
4. Slightly magnetic & slow chemical 3. Depending on welding position &
reaction with HNO3 test processes (*)
4. All the above is correct
120.In a vernier micrometer, 9 part of main
scale is divided into 10 parts of vernier 126.Two wires each 1 meter long are kept
scale, the main scale has graduation of at a distance of 0.02 mt apart if 1 amp
1 mm. Find the least count current is flowing through each wire,
then force acting on the wire will be
1. 0.01 cm (*)
2. 0.001 cm 1. Attractive if the direction of the current
3. 0.001 mm flowing through wires is same
4. 0.009 mm 2. Attractive if the direction of current will
opposite
121.The scales on the surface of a heat 3. Repulsive if direction of current will be
treatment part is removed by reverse
4. Both 1 & 3 are correct (*)
1. Using scrapper
2. Sand blasting (*) 127.The symbol represents
3. Dipping in any solvent
4. All of the above 1. SCR, rehostat respectively
2. Rehostat, thyristor respectively
122.What is the difference between 3. Resistor, FET (field effect transistor)
quantity & quality of x-ray in respectively
radiographic inspection: 4. None of the above is correct

1. Three is no meaning of quantity & 128.In which condition the bridge is said to
quality means the penetrating power of be balanced
a beam of radiation (*)
2. Quantity is related with penetrating 1. R1 is increased, R2 is decreased
power of x-ray & quality is related with 2. R3 is increased, R4 is decreased
frequency of x-ray
3. The quantity refers to the amount of
3. R2 is increased, R3 is decreased
radiation penetrating the specimen
which affects the darkness of a 129.Which one of the following statement
radiograph & quality refers to the is true?
penetrating power of a beam
4. None of the above is correct 1. In Ni-cd battery, charging & discharging
can be done rapidly due to low internal
123.Artificially aged & then cold worked is resistance. (*)
represented by
130.In case of a battery, which of the
following quantity can be stored
1. T1
2. T7 1. Energy (*)
3. T10 (*) 2. Charge
4. None of the above is correct 3. Curr3ent
4. None of the above is correct
124.Which of the following is used as filler
material 131.In a dry cell battery

1. Flox 1. Carbon electrode is placed centrally

2. Chopped fibers surrounded by aluminium chloride
3. Both 1 & 2 (*) electrolyte (*)
4. None of the above is correct

115 CORRECT ANSWER IS MARKED * AT END

REVISED OBJECTIVE QUESTIONS & ANSWERS

2. Zinc chloride is placed centrally 3. The avdel rivets must be washed in

surrounded by aluminium chloride solvent before use
electrolyte 4. 1 & 2 are correct (*)
3. Carbon electrode is placed centrally
surrounded by zinc chloride electrolyte 138.CPU contains
4. Both 1 & 3 are correct
1. I/P & O/P Unit
132.The identical insulated wire coils are 2. Memory Unit
hung from air so that they are facing 3. ALU & CU (*)
each other & supplied with same 4. All above
direction.
139.The speed of computer is in
1. Both are attracted to each other (*)
2. Both are repelled 1. Milliseconds
3. Clockwise rotation 2. Micro second
4. Anti clockwise rotation 3. Second
4. None of the above is correct (*)
133.Hot water quenching
140.Algorithm has the following properties
1. Minimizes distortion & ________
cracking (*) 1. Definiteness & finiteness
2. Ensures maximum resistance to 2. May not be finite
corrosion 3. None (*)
3. Minimizes distortion but results in
cracking 141.The computer executes
4. 1 & 2 are correct
1. One information at a time (*)
134.Spherical roller bearing take 2. Two information at a time
3. Millions of information at a time
1. Take only radial loads 4. None of the above is correct
2. Take only axial loads
3. Accept a minor degree of misalignment 142.Crevice corrosion
between opposite bearing
4. None of the above is correct (*) 1. Is an electrochemical attack
2. Takes place when metals are in close
135.Screw differ from bolt is their threads a contact with plastic (*)
fit also 3. Both 1 & 2 true
4. None of the above is correct
1. A/c bolts have generally class 3 fit &
screw class 2 fit (*) 143.Main constituent of stainless steel is
2. A/c bolts have generally class 1 fit
3. A/c bolts have generally class fir & 1. Cr (*)
screw class 3 fit 2. Ni
4. A/c screw & bolts have class 4 fit only 3. Carbon
4. None of the above is correct
136.Drill machine can do operations of
144.Which statement is true regarding
1. Drilling (*) carbon & Kevlar fibres
2. Counter sinking
3. Lapping 1. Kalvar is a type of Aramid fiber, usually,
4. All the above is correct of yellow color, having excellent tensile
strength & remarkable flexibility but
137.Which statement concerning avdel difficult to cut & drill
rivet is correct 2. Carbon fiber is a black fiber, very
strong & still. It is stronger than Kevlar
1. Avdel rivet is supplied in pre-lubricated in compression but more brittle
condition 3. Both 1 & 2 are true (*)
2. The avdel rivet is coded by length & 4. None of the above is true
diameter

CORRECT ANSWER IS MARKED * AT END 116

 REVISED OBJECTIVE QUESTIONS & ANSWERS

145.For checking zero error in a 3. High carbon steel

micrometer having arrange of 0 – 1"
153.For filling slots & key way use
1. A cylinder of 1" dia should be kept
between the faces of anvil & spindle 1. Kniffile
2. The faces of anvil & spindle will be 2. Square file
brought in close contact (*) 3. 3 – square file
3. Zero mark on the thimble is exactly 4. Half round file
inline with the datum line on it sleeve
4. The frame must be held with left hand & 154. Convert into decimal 10111011101
thimble rotated with right hand.
1. 1501 (*)
146.A ratchet mechanism is incorporated in 2. 1500
micrometer to 3. 1401
4. None of the above is correct
1. To apply correct pr.
2. To prevent damage to the instrument 155. Rheostat has
3. To have pre-set feel to prevent over
torque (*) 1. 3 terminals
4. To reduce wear on the measuring faces 2. 2 terminals (*)

147.Three point micrometer 156. In optical instrument used to inspect

the interior structure of the
1. Measures very accurately with LC of components
0.001"
2. Measures very accurately with LC of 1. Fibroscope
0.002" 2. Boroscope
3. Is used for all types of Measurement 3. Indoscope
4. None of the above is correct (*) 4. All of the above is correct (*)

148.Hawks bill ship are used to 157. If the driven gear teeth ratio is 21:40
what will be the teeth of the driven
1. Cut inside of curves / radii (*) gear
2. Cut outside of curves
3. Cut heavy sheet metal 1. 30:50
4. All of the above is correct 2. 30:35
3. 40:55
149.Included angle of BA thread id 4. 63:120

1. 35 degrees 158. Universal gate is

2. 47.5 degrees (*)
3. 33 degrees 1. AND & OR gate
4. None of the above is correct 2. OR & NOR gate
3. NOR & NAND gate (*)
150.Be laminations in composite in a coin 4. NAND gate
test gives
159. Which statement is incorrect
1. Dull sound (*)
2. Perfect solid sound 1. X-ray's reflected (*)
2. It destroys living cells
151.Tappered 1 roller bearings take 3. It produces heat
4. None of the above is correct
1. Axial & radial load in one direction (*)
2. Axial load only 160. LED concerns about
3. Axial & radial load in either direction
1. Crystals
152.Spherodise annealing is applicable to 2. Reverse Bias
3. Morelight ommited as temperature
1. Low carbon steel (*) increases
2. Medium & low carbon steel 4. Combination of holes & current (*)

115 CORRECT ANSWER IS MARKED * AT END

REVISED OBJECTIVE QUESTIONS & ANSWERS

2. Bucking bar on the rivet

161. Which is not usually done composite 3. Dimpling the rivet
4. None of the above is correct
1. Dyepenetant (*)
2. X-ray 5. For threading a hole, the hole should
3. Ultra sound method be drilled
4. Radiography
1. Approximately 0.003" to 0.007"
162. The grip length of all line fasteners is undersize (*)
given in 2. Approximately 0.003" to 0.007" oversize
3. 0.007 undersize
1. 1/100" (*) 4. None of the above is correct
2. 1/1000"
6. Secondary cell stores
163. Meuntz metal is a
1. Capacity
1. Brass & is resistant to salt water (*) 2. Energy (*)
2. Is a bronze 3. Power
4. Work
164. Which is correct
7. In a scale 39 division of main scale
1. A driven, clockwise concides with 10 division of vernier & 1
2. B driver, clockwise (*) division of main scale indicate 1 mm. 1
3. C driven, clockwise division of vernier scale indicates
4. D driven, clockwise
1. 0.01 cm
165. In the absence (substitute) of Baron 2. 0.01 mm
which composite hybrid may be 3. 1 mm
used 4. 0.001 cm

1. Aramid + Carbon / Graphite (*) 8. In a scale 24 main division is concide

with 25 division of vernier scale & 1
Paper II (February – 1998) division of main scale indicate 1 mm
then 9 division of vernier scale
1. The tool shown in figure is indicates

1. Box – end wrench 1. 0.004 cm

2. Double end offset wrench 2. 0.001 mm
3. Flare nut wrench 3. 0.01 mm
4. Combination wrench 4. 0.01 cm

2. Identify the following 9. Force to be applied on file is backward

direction
1. Rheastal & sc diode
2. Resistance & photo diode 1. To remove the cutting chips of metal
3. Rheastal & SCR force is applied on file is forward
4. None of the above is correct direction for cutting
2. For saving the life of file
3. The figure shows 3. More metal to be cut
4. None of the above is correct (*)
1. Collect
2. Tap 10. Ceramic fibres are often used with
3. Die
4. Chuck 1. Modified polyester resin
2. Exoxy resin
4. The figure shows process of 3. Metal metrix (*)
4. None of the above is correct
1. Riveting with the riveting gun on rivet
head

CORRECT ANSWER IS MARKED * AT END 116

 REVISED OBJECTIVE QUESTIONS & ANSWERS

11. In nitric acid test, the material shows 2. Decrease

rapid action with greenish blue color, 3. Infinite
the material is 4. Same

1. CRS 19. If the plate is more +ve w.r.t. cathode,

2. Carbon steel the electrons
3. Nickel (*)
4. All of the above is correct 1. Will start to flow toward plate (*)
2. Will not start to flow toward plate
12. Highest compressive strength of 3. Will start to flow toward plate but will
composite is damage diode none
4. None of the above is correct
1. Carbon / Graphite (*)
2. Ceramic 20. Which of the NDT testing method is
3. Baron suitable for the inspection of most
4. Both 1 & 2 are correct metal, plastic & ceramic surface
defects
13. Which NDT cannot be used to test a 0.5
mm Al-steel 1. Eddy current
2. Magnetic particle inspection
1. Magnetic particle inspection (*) 3. Ultrasonic test (*)
2. Eddy current test 4. Dye penetrant method
3. X-ray
4. None of the above is correct 21. How many of these factors are
considered essential of knowledge for
14. In a transformer the primary has 200 x-ray exposure
turns & the secondary has 400 turns. If
the supply of 28 v is given in primary 1. Processing of film
then the secondary voltage is 2. Material thickness & density
3. Exposure distance
1. 70 v 4. Film characteristics (*)
2. 110 v
3. 56 v(*) 22. Which type of crack can be detected by
4. 24 v magnetic particle inspection using
either circular or longitudinal
15. Calipers are used for the purpose of magnetization

1. Measure inside diameter 1. 45°

2. Measure outside diameter 2. Longitudinal
3. Measure distance between two surface 3. Transverse
4. All of the above is correct (*) 4. Sub-surface

16. The flow chart symbol indicates 23. Alclad is metal consists of

1. Activity 1. Al-alloy surface & pure Al-core

2. Input 2. Pure Al-surface & Al-alloy core (*)
3. Output 3. A homogenous mixture of pure N & N-
4. Both 2 & 3 are correct alloy
4. All are correct (Multiple layer of Al-alloy
17. "O" or "A" indicates & pure n)

1. Anhealed recrystallized (*) 24. A fibre type self locking nut must not
2. Quenched be used on a/c if bolt is
3. Forged
4. Both 1 & 2 are correct 1. Under shear load
2. Under tensile load
18. With increase in temperature, 3. Subjected to rotation (*)
resistance of cu 4. Subjected to vibration

1. Increase (*)

115 CORRECT ANSWER IS MARKED * AT END

REVISED OBJECTIVE QUESTIONS & ANSWERS

25. A triode consists of 4. None of the above is correct

1. Plate, gird & a heater 32. Flexible hose used in a/c plumbing is
2. Plate, cathode & heater classified in size according to
3. Cathode & a plate
4. Plate, cathode, heater & a screen 1. Outside diameter
between the plate & cathode (*) 2. Class sectional area
3. Inside diameter (*)
26. Diode, triode & transistors 4. All are correct

1. Obeys ohm's law 33. Which tubing has the characteristics –

2. Does not obey ohm's law (high strength & abbrassive strength)
3. Not a linear resistance for use un a high pressure (32,000 psi)
4. Both 2 & 3 are correct (*) hydraulic sysem of operation of
landing gear & flap
27. Fibre glass sheet is used between Al &
carbon / graphite joint to 1. 2024 – T
2. 5052 – O Al-alloy
1. Protect it from corrosion (*) 3. CRS (*)
2. Used as core metal 4. 1100 – ½ or 3003 – ½ H, Al-alloy
3. Provide better strength
4. All are correct 34. The setting in the micrometer indicates

28. Mark the correct statement 1. From rotary to reciprocating

2. From reciprocating to rotary
1. The diametrical pitch & pitch diameter in 3. Rotary to linear (*)
a spur gear are same 4. All the above is correct
2. If the diametrical pitch (DP) is given, you
can find out the addendum (*) 35. When a gear sector is engaged with a
3. If we divide DP by PD, we can get size rack the motion will be
of teeth
4. If the DP is given, you can fin out the 1. Intermittent rotary
addendum 2. Reciprocatry
3. Intermittent straight line (*)
29. The useful load of an a/c is the
36. Aviation ship is used for cutting
1. Difference between maximum gross
weight & empty weight (*) 1. Thick metal sheet
2. Difference between the net weight & 2. Heat treated Al. alloy & stainless steel
total weight (*)
3. Sum of the empty weight & maximum 3. Only stainless steel
gross weight 4. Any sheet metal
4. None of the above is correct
37. Headless grab screws is installed by
30. What is the color of AN-steel flared
tube filling is 1. Allen key (*)
2. Special ratchet spanner
1. Black (*) 3. Suitable screw driver
2. Blue 4. Special tool
3. Green
4. White 38. Milling machine is

31. What is the advantage of double flaring 1. Used for surface finishing
on Al-tubing 2. Used for sawing the metal
3. Used for grinding the metal
1. Easy of connection 4. All of the above is correct (*)
2. It is less resistant to the shearing effect
3. It is more resistant to shearing effect of
torque (*)

CORRECT ANSWER IS MARKED * AT END 116

 REVISED OBJECTIVE QUESTIONS & ANSWERS

39. 25 division of vernier scale concides 24

cms of main scale & 1 cm in main 1. Positive error
scale is divide into 20 equal parts 2. Negative error
3. No error (*)
1. 0.01 cm (*) 4. All are false
2. 0.05 cm
3. 0.01 cm 47. Altimeter consists of stack of
4. 0.1 cm
1. 3 evacuated capsule
40. Considering all factors the most 2. 2 evacuated capsule
commonly used metal as electrical 3. Barometric scale adjustment
conductor in a/c is 4. All are correct (*)

1. Aluminium (*) 48. Normalizing of steel is done by heating

2. Copper
3. Silver 1. Heating just above the critical point &
4. Tungsten cooling in air (*)

41. A galvanometer may be converted to a 49. In British system of electromagnetic

voltmeter by connecting flow detection is indicated by

1. Low resistance coil in parallel with meter 1. WFD

2. High resistance in parallel to meter 2. EFD
3. Low resistance in series with meter 3. MFD (*)
4. High resistance in series with meter to
increase range (*) 50. Butyl rubber used for

42. As per ATA 100 code the size & type of 1. Tyre & tube
electrical wire in aircraft are given 2. Seals & gasket (*)
3. A/C Fuel tank lining
1. By prefix & suffixes 4. None of the above is correct
2. Side by side
3. At the beginning & at the end 51. Dump flux used while welding with
4. By letters & numbers (*) oxyacetelene flame will cause

43. Transformer is a device 1. Porosity (*)

2. Crater
1. Used in transistors set 3. Channeling
2. Transfer electrical energy from one
circuit to another by changing frequency 52. Alclad is a
3. Both 1 & 2 are correct (*)
1. Aluminium alloy sandwiched between
44. Hydrogen evolves for aluminium coating (*)

1. Towards the end of the charging cycle of 53. Number of threads per inch is
Ni-cd battery (*) measured by
2. Throughout the servicing of lead acid
battery 1. Steel rule
3. When the battery is over charged 2. Screw pitch gauge (*)
4. All of the above is correct 3. Ring gauge
4. All of the above is correct
45. The strength of an electromagnet
depends on 54. Decimal 29 is equivalent to binary

1. Number of the turns of the coil 1. 11101 (*)

2. Strength of rotation of the magnet 2. 101101
3. Speed of rotation of the magnet (*) 3. 110101
4. All of the above is correct 4. 101011

46. The setting in vernier caliper indicates 55. SCR has

115 CORRECT ANSWER IS MARKED * AT END

REVISED OBJECTIVE QUESTIONS & ANSWERS

1. Al clad
1. 2 terminals 2. Pureclad
2. 3 terminals (*) 3. Pure clad & electro statically preventive
4. All of the above (*)
56. In pitot & static system static vents &
pitot vents are placed at separated 64. Bearing strength is
location to prevent
1. The strength that resists a force that
1. Position error tends to tear it apart (*)
2. Ice firmation
3. All of the above is correct (*) 65. In NDT X-ray equipment are graded
according to the
57. Difference of both pressure is
measured 1. Volt – range (*)
2. Electromagnetic radiation
1. Altimeter 3. Amp
2. ASI (*) 4. Penetrating power

58. The phenomenon which causes 66. To improve the tensile strength,
continuous spin of outer ring due to ductility & shock resistance,
coincidence of rotor ring with outer magnesium alloy castings normally
gimble ring axis is called
1. Case hardened
1. Gyro wander 2. Solution heat treated (*)
2. Apparent precession 3. Precipitation heat treated
3. Gyro tumbling 4. Solution heat treated
4. Gimble lock (*)
67. Thermistor
59. For brazing the flame used
1. Zero temperature coefficient
1. Oxitizing 2. Variable temperature coefficient
2. Carbonizing 3. Positive temperature coefficient
3. Neutral (*) 4. Negative temperature coefficient (*)
4. Reducing
68. 7075 – 0 indicates
60. High carbon steel co9ntains carbon
1. Full annealed condition (*)
1. 0.50% - 1.5%
2. 0.30% - 1.50% 69. Which of the following revet does not
3. 0.50% - 1.05% (*) required heat treatment
4. 1.50% - 2.2%
1. 2017 – D
61. Crack at the surface should be welded 2. 2117 (*)
by 3. 2024 – DD
4. 2117 – AD
1. Butt welding (*)
2. Lap welding 70. In oxyacetelene welding equipment
3. Fillet welding oxygen & acetylene are identified by

62. In chalk test we used 1. Left & right hand thread

2. Color & length of cylinder
1. Hot fluid 3. Diameter of the hose
2. Cold fluid 4. Both 1 & 2 are correct (*)
3. Both are correct (*)
4. None of the above is correct 71. Cleaning of acrylic & rubber is done by

63. Al. alloy core with pure alluminium 1. MEK

coating is knows as 2. Aliphatic naptha (*)
3. Aeromatic naptha

CORRECT ANSWER IS MARKED * AT END 116

 REVISED OBJECTIVE QUESTIONS & ANSWERS

4. Acetone 3. Shank length of the revet

72. Elastomeric rubber is 81. In a revet layout the shank diameter

should be
1. Rubber impregnated in metal
2. Shock absorber (*) 1. Twice the thickness of the thicker sheet
2. 1/8th thickness of the thicker sheet
73. NDT of aluminium alloy is done by 3. Three times the thickness of the thickest
sheet (*)
1. Penetrant method
2. Zyglo method 82. In a bolt & nut assembly after applying
3. X-ray method torque, cotter pin hole is not aligning
4. Ultrasonic method (*) the bolt my be

74. Heat treatment aluminium alloy is done 1. Slightly tightened to next slot (*)
by 2. Slightly loosened to next slot

1. Heating KOH & NAOH (*) 83. A/C chains are specified by
2. Heating above critical point & cool in air
1. Load carrying capacity
75. UFD indicates 2. Pitch & number of links
3. Both are the above is correct (*)
1. Ultrasonic flow detection (*)
2. Radiography 84. Helicoil insert has a natch & tang along
3. Dye penetrant flow detection end to

76. Welding for stainless steel the flame 1. Facilitate installation

used 2. The removal of tang after it has screwed
into the trapped thread hole (*)
1. Carbursing
2. Neutralizing (*) 85. Unless specified the torque to be
3. Dye penetrant flow detection applied to a bolt & nut assembly should

77. Welding for stainless steel the flame 1. Degreased dry & clean thread (*)
used 2. Lubricated thread

1. Carbursing 86. Raised double dash rivet is

2. Neutralizing (*)
3. Caldizing 1. 2117 rivet
2. 2024 rivet (*)
78. Carbon in iron at normal temperature
remains as 87. Crinckle washer is used for

1. Ferrite (*) 1. Hard steel to take food

2. Dissolved iron matrix 2. Instrument mounting for loft load &
3. Austenite electrical installation (*)
4. Special iron matrix
88. Cotterpin for castellated nut is made off
79. Baffles in hydraulic tank is given for
1. Stainless steel
1. Providing an expansion tank is given for 2. Corrosion resistant steel
2. Resisting fuel surging within the tank (*) 3. Cadmium plated low carbon steel (*)
3. Providing internal structural integrity 4. Both 1 & 3 are correct
4. Preventing fuel overflow during refueling
89. Circuit containing registor, capacitor,
80. In a blind revet the length between diode, seminconductor is a
manufacture head to the end is
1. Linear circuit
1. Grip length (*) 2. Non linear circuit
2. Grip range

115 CORRECT ANSWER IS MARKED * AT END

REVISED OBJECTIVE QUESTIONS & ANSWERS

3. Bipolar circuit 98. Every third tooth of the hackshaw is

4. Unipolar circuit made straight

90. 1110101 is equivalent to 1. To give clearance for the cutting

2. Repsaw tooth is provided
1. 117
2. 29 99. The vernier scale has
3. 63
4. None of the above is correct 1. Positive error
2. Negative error
91. In lad acid battery sedimentation
occurs because of 100.Least count is defined as

1. Overcharging 1. One main scale division is divided into

2. Frequent charging & discharging the total division of the vernier / thimble
3. Over discharging (*) scale (*)
4. High rate of discharge 2. 1 MSD – 1 TSD

92. A circular mill is 101.Least count of 50 divisions on the

circle of micrometer whose pitch is 1
1. A circular whose diameter is 0.001" (*) mm

93. Vent plug of Ni-cd battery should be 1. 0.01 mm

cleaned by 2. 0.02 mm (*)
3. 0.5 mm
1. Distilled water only (*) 4. 0.0902 mm
2. Distilled water & detergent
3. Hot water & distill water 102.Backslash of a micrometer is caused
4. Detergent due to

94. Current is 2.5 amp, voltage 12 v, used 1. Manufacturing defect

for 1 minute. How much energy it will 2. Wear & tear
consume 3. Wear on the nut
4. All of the above correct (*)
1. 1800 J (*)
2. 2J 103.Snap gauge is a
3. 60 J
4. 18 J 1. Go & number go gauge (*)
2. It will snap at preset torque load
95. In British system of drawing the 3. Gauge which measure TPI
inverted triangle gives 4. Gauge which measured outside
diameter
1. Important dimensions
2. Heat treatment 104.Aviation snip used for cutting
3. Surface finish (*)
1. Stainless steel & aluminium alloy heat
96. Micron is treated sheet (*)
2. Chromium sheet
1. Millionth of meter (*) 3. Heavy sheet metal
2. Thousandth of meter 4. Any sheet metal

97. A hole to be reamed should be drilled 105.Gyroscope – the phenomenon which

to under causes continious spin of outer ring
due to coincidence of rotor ring with
1. 0.001" – 0.002" cuter gimble ring axis is called
2. 0.003" – 0.007" (*)
3. Same size 1. Gyro wander
2. Gyro tambling
3. Apparent precession

CORRECT ANSWER IS MARKED * AT END 116

 REVISED OBJECTIVE QUESTIONS & ANSWERS

4. Gimble lock (*) 3. Hard Disc

4. Micro processor chips
106.Rate of turn indicator
2. T6 designation of Al-alloy indicates
1. Rate gyro (*)
2. Tied gyro 1. Solution heat treated & then artificially
3. Earth gyro aged (*)
4. Free gyro 2. Solution heat treated & then stabilized
3. Artificially aged only
107.Difference of pilot & static pressure is 4. Solution heat treated & then cold worked
measured by
3. 0.10 mm is equivalent to
1. ASI (*)
2. Altimeter 1. 0.039"
3. VSI 2. 0.041"
3. 0.035"
108.Altimeter operation mechanism 4. 0.045"
consists of a
4. The major alloying element in 7075 Al-
1. Two aneroid capsule alloy is
2. Three aneroid capsule
3. Adjustment for barometric pressure 1. Magnesium
provided 2. Silicon
4. All of the above is correct (*) 3. Mg & Si
4. Zinc (*)
109.Free gyro has
5. The purpose of turnbuckle is to
1. The plane of freedom
2. The planes are right angle to each other 1. Make minor adjustment in cable length
& three plane (*) 2. Adjust cable tension
3. Both 1 & 2 are correct (*)
110.Turn & slip indication operates 4. None of the above is correct
respective by
6. A 7 × 19 cable is made up of
1. Gyro only (*)
2. External force & gravity 1. 7 strands of 19 wire each (*)
3. Gyro & gravity 2. 19 strands of 7 wire each
3. Both are correct
111.Acceptable deviation in compass from 4. None of the above is correct
the equipment
7. For cast iron, the included angle of drill
1. 1 degree from the needle to the is
compass
2. 2 degree from the needle to the
compass (*) 1. 118° (*)
3. 3 degree from the needle to the 2. 70°
compass 3. 90°
4. 140°
112.Spherical roller bearing will take
8. Select the correct sta5tement
1. Radial load heavy
2. Axial load slightly 1. Hand taps are available in two sets
3. Both the above are correct (*) 2. Bottoming tap is used to smoothen the
bottom of a blind hole
Paper – II (June – 1999) 3. Plug tap is used at the last
4. Taper tap is used first (*)
1. The main memory of a computer is
9. The external threads on a bar is made
1. RAM (*) by
2. ROM

115 CORRECT ANSWER IS MARKED * AT END

REVISED OBJECTIVE QUESTIONS & ANSWERS

3. ¼ to ½ T
1. Taps 4. 1 1/3 T to 1 ½ T
2. Stock
3. Dies (*) 17. In a fillet weld, the penetration
4. Reamer requirements are

10. The defect in wheel plus is inspected 1. 60 to 80% of the thickness of the base
by metal
2. 100% of the thickness of the base metal
1. Dye penetrant process (*) 3. 200% of the thickness of the base metal
2. Magnetic particle inspection 4. 25 to 50% of the thickness of the base
3. Eddy current testing metal (*)
4. Ultrasonic testing
18. In the fluerescent penetrant inspection,
11. The voltage rating of fully charged cell
of 20 Ni-cd battery is 1. The defect will show the flow as a
brilliant yellow green (*)
1. 1.8 to 2.1 v 2. The defect will show the flow as a light
2. 1.24 to 1.3 v yellow green
3. 1.4 to 1.7 v 3. The sound area will appear white (deep
4. 1.3 to 1.5 v (*) blue violet)
4. The diffect will show as deep blue violet
12. If the temperature of a confined liquid
is held constant & its pressure tripled, 19. In jacking of aircraft
the volume will be
1. Main wheels are raised together (*)
1. Triple 2. Nose wheel is raised 6" above the
2. Be reduce to 1/3rd its original (*) ground
3. Remain the same 3. Nose wheel is raised for free movement
4. None of the above is correct of it
4. None of the above is correct
13. If the pitot head is blocked then which
instrument is affect 20. Centre drill is used to

1. ASI (*) 1. Make hole & reaming in one operation

2. Altimeter 2. Make hole & countersunk in one
3. Turn & bank indicator operation (*)
4. Slip indicator 3. Make taper hole
4. All of the above
14. Which statement is correct
21. Unless otherwise specified, torque
1. QNE setting gives height above sea value for tightening a/c nuts & bolts
level of the airport relate to
2. QNH setting gives airfield elevation
3. QFE setting makes the altimeter read 1. Clean dry thread (*)
zero on landing at aerodrome (*) 2. Clean Lightly oiled thread
4. All of the above is correct 3. Either 1 & 2
4. None of the above
15. A double flare should be used on
22. A fibre type, self locking nut must
1. Stainless steel never be used on an a/c if the bolt is
2. Nickel steel
3. Cast iron 1. Under shear loading
4. Al alloy only (*) 2. Under tension loading
3. Both tension & shear loading
16. Bead width of bolt weld should be 4. Subjected to rotation (*)

1. 2 to 3 T 23. Aircraft bolts are usually manufactured

2. 3 to 5 T with a

CORRECT ANSWER IS MARKED * AT END 116

 REVISED OBJECTIVE QUESTIONS & ANSWERS

4. All of the above is correct

1. Class 1 fit for the threads
2. Class 2 fit for the threads 29. With an ohmmeter connected into the
3. Class 3 fit for the threads (*) circuit as shown, what will ohmmeter
4. Class 4 fit, for the threads read

24. Generally speaking, bolt grip length 1. 20 Ω

should be 2. Infinite
3. 10 Ω
1. One & one half times the thickness of
4. None of the above is correct
the material through which the extend
2. Equal to the thickness of the material
30. How can the state of charge of a Ni-cd
through which they extend plus
battery be determined
approximately one diameter
3. Equal to the thickness of the material
1. By measuring the specific gravity of the
through which they extend (*)
electrolyte
4. 2 times the diameter
2. By measuring charge (*)
3. By the level of electrolyte
25. A particular component is attached to
4. All of the above is correct
the a/c structure by the use of an a/c
bolt & a castleted tension nut
31. Zero fuel weight is the
combination, if the cotter pin hole does
not align with the recommended torque
1. Dry weight plus the weight of full crew,
range, a acceptable practice is
pax & cargo
2. Basic operating weight without fuel
1. Exceed the torque range
3. Maximum permissible weight of a
2. Lubricate the threaded section of the
loaded a/c including pax, crew, cargo
nut, bolt & torque
without fuel (*)
3. Change washers & try again (*)
4. Maximum weight of the a/c with crew,
4. Change the nut
oil, pax, less fuel in wing tank
26. How is a clevis bolt used with a fork
32. The empty weight of an aircraft is
end cable terminal secured
determined by
1. With a shear nut lightened to a sung fit,
1. Adding the net weight of each weighing
but with no strain imposed on the fork &
point & multiplying the measured
satefied with a cotter pin
distance to the datum
2. With a castle nut tightened until slight
2. Subtracting the tare weight from the
binding occure between the fork & the
scale reading & adding the weight of
fitting to which it is being attached
each weighing point (*)
3. With a shear nut & cotter pin or a thin
3. Multiplying the measured distance from
self locking nut tightened enough to
each weighing point to the datum times
prevent rotation of the bolt in the fork
the sum of scale reading less the tore
(*)
weight.
4. All are correct
33. Compound gear is used for
27. A bolt with an X (cross) inside a
triangle on the head is classified as a
1. Better efficiency
2. Better transmission of motion
1. Standard a/c bolt
3. Greater range of speed
2. Close tolerance bolt NAS (*)
4. All of the above is correct (*)
3. CRS bolt
4. Special bolt
34. Mg-alloy used with other metal should
be
28. Through which material will magnetic
lines of force pass the most
1. Given two coasts of zinc chromate & a
layer of pressure – sensitive _____ tape
1. Copper
0.003 in thick is applied smoothly &
2. Iron (*)
3. Aluminium

115 CORRECT ANSWER IS MARKED * AT END

REVISED OBJECTIVE QUESTIONS & ANSWERS

firmly enough to prevent air bubbles & 41. Jet fuel identifiers are
wrinkles (*)
2. Given one coat of zinc chromate & a 1. Performance number to designate the
coat of pressed vinyl volatility of the fuel
3. Given two coat of zinc chromate & two 2. Performance number & are relative to
coat of pressed vinyl the fuel performance in the a/c engine
4. None of the above is correct 3. Type number with no relation to the fuel
is performance in the aircraft engine (*)
35. An automotive type flaring tool will 4. None of the above is correct
produce a flare
42. Brinell hardness testing is applicable to
1. 37 degree
2. 45 degree (*) 1. Small part & high hardness
3. 60 degree 2. Large part & small hardness
4. 30 degree 3. Small part & small hardness
4. Large part & high hardness (*)
36. Color of AVGAS low lead fuel is
43. Which one id incorrect
1. Died blue (*)
2. Color less 1. ATA – 62 communication
3. Died green 2. ATA – 30 ice & rain protection
4. None of the above is correct 3. ATA – 52 dcor
4. ATA – 78 engine exhaust
37. With prepregs
44. What will be the speed of driven gear if
1. Manual application not required driver gear is 120 rpm.
2. Has to be kept in freeze
3. Both 1 & 2 are correct (*) 1. 60 rpm
4. None of the is correct 2. 120 rpm
3. 100 rpm
38. The measurement reading on the 4. 240 rpm
illustrate micrometer is
45. In dye penetrant test, the vol, of defect
1. 0.2857" can be interpreted by
2. 0.2901"
3. 0.2511" 1. Staining route
4. 0.2861" 2. Staining extent (*)
3. Staining speed
39. A primary cause of inter granular 4. All of the above is correct
corrosion is
46. The test sample which can be tested by
1. Improper heat treatment (*) making both probe simultaneously in
2. Dissimilar metal contact opposite direction to defect flames on
3. Improper application of primary surface
4. None of the above is correct
1. Flash butt metal (*)
40. Galvanic corrosion is likely to be most 2. Thin sheet metal
rapid & sever when 3. Cast ingot
4. None of the above is correct
1. The surface area of the cathodic metal
is similar than surface area of anodic 47. During repair procedure of composite,
metal part heat treatment is done for
2. The surface area of the anodic &
cathodic metals are approximately the 1. Small disbond
same 2. Seal be smallest
3. The surface area of the anodic metal is 3. Restore surface protection
smaller than the surface area of the 4. None of the above is correct (*)
cathodic metal (*)

CORRECT ANSWER IS MARKED * AT END 116

 REVISED OBJECTIVE QUESTIONS & ANSWERS

48. When grain size of the steel will be 3. Turn buckle barrel ends (*)
smallest 4. Steel tubular members of basic structure

1. Heated first below critical range 55. When welding a high carbon steel use
2. Heated just above critical range (*) a
3. Below lower critical range
4. None of the above is correct 1. Low carbon rod
2. High carbon rod (*)
49. If a body is given shape & lorituation is 3. Rod of either low or high carbon content
exposed to uniform flow of 4. Rod of intermediate carbon content
incompressible fluid, each component
of the force which the fluid exerts the 56. High carbon steel can be readily
body can be expressed as product of welded by

1. Area 1. Are welding procedure

2. Dynamic pressure 2. Oxidizing flame & high carbon rod
3. Reynolds no. 3. Neutral flame & high carbon rod (*)
4. All of the above is correct 4. Carbonising flame & low carbon rod

50. PARAL KETONE is used for preventing 57. N.W.V.

corrosion of
1. Strength of the compositor material
1. Mg alloy parts 2. Strength of the material & composing
2. Welded steel structure with charge
3. Cables, ferros & non ferros (*) 3. Strength of reinforcing fibre
4. B&C 4. None of the above is correct

51. The process used for checking 58. An flared tube fitting is made of
moisture extrapped in composite is
1. Al (*)
1. Radiography 2. Cu base alloy
2. Ohmmeter 3. Steel
3. Laser holography 4. All of the above is correct
4. All of the above is correct (*)
59. Correct statement regarding refueling
52. What procedure is used to digtinguish is
heat treatable alloys from non heat
treatable alloys 1. Earthing is not required
2. Disconnect the earthing line first before
1. 10% solution of caustic soda (*) disconnecting the fuelling nozzle
2. 5 % solution of muriatic acid 3. If a/c is earthed, fuelling vehicle, doesn't
3. Rockwell test require earthing
4. 10% solution of H2Sc 4. None of the above is correct (*)

53. When welding various metals you may 60. Scales are removed from lightly
reduce the chances crack of during by stressed steel parts by

1. Preheating (*) 1. Hard abrasive paper

2. Anodizing 2. Buffing Wheel (*)
3. Heat treating 3. Wire brush
4. Clamping 4. None of the above is correct

54. Which of the follow of a/c parts or units 61. If you have some 178 rivet, above 3/16"
should not be welded in diameter that had been aged for the
hours after quenching
1. Items which are not responsive to heat
treatment 1. You could use them frouding they have
2. Plain carbon, Ni-steel of SAE 2300 not exceeded 5 hours of ageing
series

115 CORRECT ANSWER IS MARKED * AT END

REVISED OBJECTIVE QUESTIONS & ANSWERS

2. You could not use them because 178

rivets should be used within 10 minutes 68. When flaring Al-tubing for used with AN
after quenching coupling nuts & sleeves, the flat angle
3. You could use them provided they had should be
not exceeds 3 hours of ageing
1. 67°
62. Flux from ferrous metals can be 2. 45°
removed by using
3. 37° (*)
1. 25% sol of silver nitrate 4. 60°
2. No need of flux by welding ferrous
metals 69. The dia of flexible hose for a/d
3. You have to remove flux from ferrous plumbing is classified in size according
metals (*)
4. A wire brush 1. Cross sectional area
2. Inside dia (*)
63. A flux for silver soldering is obtained 3. Outside dia
by using 4. Both 1 & 2 are correct

1. Zn Cl2 (*) 70. Make an external thread which tool is

2. Nitric acid used
3. Muriatic acid
4. None of the above is correct 1. Tap
2. Threaded spanner
64. Welding of a/c from welding of steel 3. Die (*)
differs in that 4. None above is correct

1. It is considered harder to weld because 71. Pulleys are normally made of

of high temp.
2. Steel does not have a color change that 1. Asbestos
is apparent in Al 2. Pnenolic formaldehyde (*)
3. M.P. of Al is much lower than steel & the 3. Mica
expansion is nearly three times as great 4. Both 1 & 2 are correct
(*)
4. It is much easier to weld because a flux 72. Function of turnbuckle is to
is used
1. Adjust the cable tension
65. Wrought iron is identified by 2. Adjust the minor length of cable
3. Both 1 & 2 are correct (*)
1. Red colored spark 4. As in a, & for frequently connecting &
2. Straw yellow spark (*) disconnecting the cable
3. White spark
4. None of the above is correct 73. Mark the correct statement

66. Which gage of telescoping gauge is 1. The weld should be taper off smoothly
identified by its into the base metal
2. The depth of penetration should be
1. 1/16 to 6" different to ensure fusion of the filler rod.
2. 5/18 to 6" 3. The height of the weld should be 1/8
3. 5/8 to 6" inch above the base metal
4. ½ to 6" (*) 4. The ripples should be even & well
feathers into the ________ metal which
67. Line used to show an edge which is not shows no burn due to overheating (*)
visible is a
74. Mark the correct statement
1. Break line
2. Hidden line (*) 1. Fibre lock nut should not be used on the
3. Imaginary line place where vibration is more
4. Phantom line

CORRECT ANSWER IS MARKED * AT END 116

 REVISED OBJECTIVE QUESTIONS & ANSWERS

2. Fibre lock nut should not be used on the 1. White color

place where temp is above 250° F (*) 2. Greenish color (*)
3. Fiber lock nut should not be used on the 3. Blue color
place where there is relative motion 4. Redish color
between parts
4. Both 2 & 3 are correct 82. Monel is the alloy of

75. Al clad is 1. Cu-steel

2. Ni-steel (*)
1. Coating of Al alloy on the pure Al 3. Inconel
2. Coating of pure Al on the Al-alloy (*) 4. Chromel
3. Coating of pure Al on non-metal
4. None of the above is correct 83. Self locking nuts should be replaced
when
76. In SAE 2040, the last two digits
indicates 1. It is easily tightened by fingers (*)
2. Its locking property decreases
1. Percentage of alloying element 3. Its inside dia equal to outside dia of the
2. Percentage of carbon content (*) corresponding bolt threads
3. Number of carbon molecules 4. All above is correct
4. Both 2 & 3 are correct
84. The length of file is measured from
77. Parts should be normalized after
welding 1. Tang to tip
2. Heel to tip (*)
1. To relieve internal stresses (*) 3. Tip to secreted portion
2. To remove the surface scale formed 4. None of the above is correct
during welding
3. To introduce slight amount of carbon to 85. Water in the honey comb structure may
improve the surface harness of the weld be detected by
4. To make improve mechanical property of
the metal 1. Floor ascent inspection method
2. Ultrasonic inspection method
78. Match the following 3. Radiographic inspection method (*)
4. Eddy current inspection method
GEAR BEARING HARNESS
TESTER 86. To transmit the rotating motion
1. Bowel Needle Spark between the shaft & wheel & to allow
2. Ball Rockwell Idler parallel movement of the wheel at the
3. Idler Ball Rockwell (*) same time, the type of key is used.
4. Needle Bowel Ball
1. Woodruff key (*)
79. The bolts are manufactured in 2. Flat saddle key
3. Feather key
1. Class 2 fit 4. Hollow key
2. Class 1 fit
3. Class 3 fit (*) 87. The size of drill is indicated by
4. There is no fit for a/c bolts
1. Letter 'A' to indicated smallest size
80. Purpose of tempering is to 2. Letter 'Z' to indicated longest size
3. Letter 'z' to indicated smallest size
1. Reduce the softness 4. Both 1 & 2 are correct (*)
2. Reduce the brittleness due to hardening
(*) 88. Purpose of heat treatment is
3. Improve the softness / toughness
4. Both 2 & 3 are correct 1. To improve electrical & mechanical
property
81. Corrosion on copper in indicated by 2. To relieve internal stresses
3. To make material harder & stronger
4. All of the above is correct (*)

115 CORRECT ANSWER IS MARKED * AT END

REVISED OBJECTIVE QUESTIONS & ANSWERS

96. In case of ultrasonic transmission

89. To carry the petroleum & synthetic fluid method, which statement is correct
which hose material is used
1. In pulse transmission there is only one
1. Teflon (*) peak
2. Butyl 2. As in (1) & if there is only one peak
3. Buna – N 3. In pulse transmission there is two peak
4. Synthetic 4. As in (3) & if there is another peak
between transverse & bottom it indicate
90. The value of induced emf depends on flaw (*)

1. The speed of rotation 97. To case of chromium plating the

2. The length of the magnetic field current density should be
3. The number of wires moving through the
magnetic field (*) 1. Between 150 – 200 amp, per sq. ft
4. All above is correct 2. Between 150 – 200 amp, per sq. ft
3. Between 100 – 250 amp, per sq. ft
91. In case multimeter 4. Between 100 – 200 amp, per sq. ft

1. Red lead indicating negative terminal 98. Coating of aluminium metal in powder
2. Red lead indicating positive terminal process is called
3. Black lead indicating negative terminal
(*) 1. Sheradizing
4. Black lead indicating positive terminal 2. Granodizing
3. Anodizing
92. Mark the correct statement 4. Colorizing (*)

1. A fuse is a strip of metal that melts when 99. In balanced pressure type torch
excessive current flow through it
2. A circuit breaker is device that stop 1. O2 & acetylene comes at the same
current flow when it exceeds a pre- pressure
determined value 2. O2 & acetylene comes at the different
3. Both 1 & 2 are correct (*) pressure
4. A.C.B. is devised that melts when 3. As in (1) & have equal size (*)
excessive current flow through it. 4. None of the above is correct
93. The specific gravity of electrolyte in 100.Radiographic inspection are used to
incase of Ni-cd battery is defect
1. Between 1.240 to 1.300 (*) 1. Internal & external crack
2. Between 1.225 to 1.275 2. Porosity
3. Between 1.225 to 1.300 3. Water in the honey comb core
4. None of the above is correct 4. All of the above is correct (*)
94. Battery can be charged by 101.In flexible back blade
1. Constant current method 1. Only the part where the teeth are cut is
2. Constant voltage method hardened
3. Both 1 & 2 are correct (*) 2. Only the end position where holes are
4. None above is correct drilled is hardened
3. As in (1) & rest of the blade remaining
95. Spray quenching is normally carried on soft (*)
4. Both 1 & 2 are correct
1. Large parts
2. Small parts 102.Half round file is suitable for filing
3. Almost al-alloy
4. As in 1 & 3 & minimizes distortion & 1. Irregular shape
alleviates quench cracking 2. Large internal radius
3. Both 1 & 2 are correct (*)

CORRECT ANSWER IS MARKED * AT END 116

 REVISED OBJECTIVE QUESTIONS & ANSWERS

103.Which type of punch should be used to 1. Oxygen

take out rivets, split pins, shack 2. Indicating & recording
3. Landing gear (*)
1. Drift punch 4. Light
2. Pin punch (*)
3. Center punch 110.Color of dye used in pendants dye
4. Prick punch process is

104.Minimum number of gear required to 1. Brown

make a compound gear train is 2. Red (*)
3. White
1. 3 4. None of the above is correct
2. 2
3. 4 (*) September 1993
4. More than 2
1. Knurling is the
105.Which statement is correct for stub
tooth 1. Rolling depression on the soft material
2. Rolling depression on any kind of
1. Stud tooth is thicker in proportion to its material
length 3. As in (2) & is used to provide proper grip
2. It is used where more strength is (*)
required 4. None of the above is correct
3. Its operation is not as smooth as
involutes tooth 2. To make stretch in the direction of its
4. All above is correct (*) width

106.The transmit reciprocating motion into 1. Use straight peen hammer (*)
rotary motion, which type of gear 2. Use cross peen hammer
normally used 3. Any kind of hammer can be used
4. Use ball peen hammer & apply blow
1. Rack & sector with an angle
2. Sector & gear
3. Rack & pinion (*) 3. Protective jaw caps are used with vice
4. Not possible with gear
1. To protect the vice jaw
107.Which statement is correct regarding 2. To protect the parts from becoming
shrink rule damage (*)
3. To apply constant & even pressure on
1. It has number 4 graduation the parts
2. The inch marking on the faces are 4. All of the above is correct
slightly longer than actual inches
3. It is made from 1/10 to 7/16 inch per ft 4. To make a V-shaped groove the chisel
over size commonly used is
4. All the above is correct (*)
1. Round nose chisel
108.In order to locate a defect in a part 2. Flat chisel
which condition is necessary 3. Cap chisel
4. Diamond point chisel
1. Magnetic lines of forces must pass
parallel to the defect 5. To locate the center on a round block
2. Magnetic lines of forces must pass use
perpendicular to the defect (*)
3. Induced magnetic flux in more than one 1. Surface gauge
direction 2. Center square head (*)
4. Both 2 & 3 are correct 3. Hermophrodite caliper
4. All of the above is correct
109.ATA 100 specification system, 32
indicates 6. Which cutting fluid is used on tool steel

115 CORRECT ANSWER IS MARKED * AT END

REVISED OBJECTIVE QUESTIONS & ANSWERS

1. A suspended magnet always assume a

1. Mineral land oil north & south position (*)
2. Soluble oil & (1) is correct 2. Inductors when connected in parallel the
3. Sulfurized oil total inductance is the south their values
4. All above is correct (*) 3. Inductive reactance is inversely
proportional to inductance & frequency
7. Mark the correct statement 4. All of the above is correct

1. Linear sidewise motion is known as 14. Which instrument is used for checking
backlash the insulation resistance
2. Reaming should be down after drilling
3. As diametral pith increases, size of tooth 1. Ohm meter
decreases, no. of teeth increases 2. Megger (*)
4. All of the above is correct (*) 3. As in (1) & maghometer
4. All of the above is correct
8. Mark the correct statement
15. 'D' Arsonavel ammeter is used
1. Coating of pure Al & Al-alloy is called
2. Titanium has low strength to weight ratio 1. For measuring ammeter AC current
3. Brass & bronze comes under copper 2. For measuring DC current (*)
4. Both 1 & 3 are correct 3. For measuring AC voltage
4. For measuring DC voltage
9. Which instrument is used for
measuring the roughness of surface 16. Mark the correct statement

1. Surface gauge 1. Specific gravity reading between 1.300

2. Surface plate with v-block (*) to 1.275 indicates a high of charge
3. Profilometer 2. Specific gravity reading between 1.275
4. Pyrometer to 1.240 indicates a high of charge
3. Specific gravity reading between 1.240
10. Conductor having length of 2 ft & to 1.225 indicates a medium charge
resistance 2 ohms, now if we reduce its 4. Both 1 & 3 are correct (*)
length just half of original, then
resistance will be 17. In triode tube

1. Just double 1. Srid is placed between plate & cathode

2. Just half (*) (*)
3. Just equal 2. Plate is placed between grid & cathode
4. None of the above is correct 3. Cathode is placed between grid & plate
4. None of above is correct
11. Which instrument is utilizing both
dynamic & static air for its operation 18. The size of the flexible hose is
determined by its
1. Altometer
2. VSI 1. Outside dia
3. ASI (*) 2. Inside dia (*)
4. Both 1 & 3 are wrong 3. Number of piles to makes hose
4. Cross section area
12. The sensitively of altimeter is increased
by increasing 19. Mark the correct statement

1. Number of gears & sectors 1. Dia of bolt in 1/16th & length in 1/8th (*)
2. Number of gears & pinion 2. Dia of bolt in 1/8th & length in 1/16th
3. Number of capsules (*)
4. Both 1 & 3 are correct
3. Dia of rivet in 1/16th & length in 1/32 th
4. Both 1 & 3 are correct
13. Mark the correct statement
20. To prevent sparking

CORRECT ANSWER IS MARKED * AT END 116

 REVISED OBJECTIVE QUESTIONS & ANSWERS

1. Connect the condenser in series with 27. A/C cables are normally made of
the part
2. Connect the condenser in parallel with 1. Carbon steel
the part (*) 2. CRS
3. Connect the condenser in any desire 3. Galvanized steel
position 4. Both 1 & 2 are correct (*)
4. Both 2 & 3 are wrong
28. Mark the correct statement
21. When capacitor is connected in
parallel, which formula is used 1. Hermaphrodite caliper is used as a
determining the total capacitance marking gauge in layout work
2. In commercial normalizing quenching is
1. 1/C = 1/C1 + 1/C2 + 1/C3 normally carried out in air
2. C = C1 = C2 + C3 (*) 3. The color of spark in gray cast iron is
red at the point of contact
3. C = 1 / (C1 + C2 + C3) × C1 + C2 + C3 4. All above is correct (*)
4. None of the above is correct
29. The given figure indicates
22. Piezoelectric effect is found on
1. NPN transistor
1. Rochelle salt 2. PNP transistor
2. Phenolic material 3. As in (1) & arrow indicating emitter
3. Quanty & rochelle salt 4. As in (2) & arrow indicating emitter
4. Both 1 & 3 are correct (*)

23. Which is the correct statement

30. In heat treatment of material T8
indicating
1. Gasket are always used with backup
ring 1. Solution heat treatment & then stabilized
2. Gasket are stationery seals 2. Solution heat treated & artificially edged
3. Gasket can be used as an oil seal & then cold worked
4. Both 2 & 3 are correct (*) 3. Solution heat treated & cold worked &
then artificially edged (*)
24. A bolt having part number AW 3 DD 6A 4. Solution heat treated, & then artificially
having following means edged

1. It indicates that bolt dia is 3/16", length 31. In Rockwell hardness tester there is
6/8" & material 2024 two weight except weight pan of
2. It indicates that bolt dia is 3/8", length machine, one is red & other is black.
6/16" & material 2024 (*) Now choose correct answer
3. It indicates that bolt dia is 3/8", length
6/16" & material corrosion resistant steel 1. When there is no load machine applied
4. It indicates that bolt dia is 3/16", length a load of 60 kg
6/18" & material corrosion resistant steel 2. Where black wt. is on the pan, machine
applied a load of 150 kg
25. AN 300- series is used for indicating 3. As 1 & 2 & when red wt. is on the pan
machine applies a load of 100 kg
1. A/C screws 4. As a, b, & c & black wt. is always used
2. A/C nuts (*) with red wt. (*)
3. A/C washers
4. A/C bolts 32. Titanium is heat treated for the purpose
of
26. The length & dia of DZUS fastener is
measured jin 1. Thermal hardening to improve strength
2. Annealing after hot working or cold
1. Length 1/8" & dia 1/16 inch working
2. Length 1/16" & dia 1/8" inch 3. Relief of stresses setup during cold
3. Length 1/8" & dia 1/100 inch (*) working
4. Length 1/100" & dia 1/16" inch 4. All above is correct (*)

115 CORRECT ANSWER IS MARKED * AT END

REVISED OBJECTIVE QUESTIONS & ANSWERS

33. Filler are added in resin to 40. Wing type bolts self locking nuts are
made in range of
1. Increase strength
2. As in 1 & 2, also control viscosity & wt 1. No. 6 upto ¼"
3. Increase pot, life
4. As in (2) also control viscosity & wt (*) 41. The material used for making the tap is

34. Mark the correct statement regarding 1. Stainless steel

composite material 2. Hard tempered steel
3. Cast iron
1. Carbon / graphite is stronger in 4. Tool steel (*)
compressive strength (*)
2. Color of kevler is brown 42. The included angle of center punch is
3. S-glass is borosilicate glass
4. All above is correct 1. 80°
2. 75°
35. Mark the wrong statement
3. 60°
1. Nomex is the widely used core material 4. 90° (*)
2. Urothane can not be cut by hot wire
cutter MARCH – 1992
3. Carbon is identified by its black color
4. Ciramic fibre are in not used with metal 1. In ATA 100 specification system
matrix (*) chapter 61 in indicating

36. Stress corrosion occurs as a result of 1. Rotars

2. Propellers (*)
1. Combined effect of tensile stress & lack 3. Wings
of uniformity in alloy structure 4. Powerplant
2. Relative motion between two parts
3. Combined affect of tensile strength & 2. The tile block having following
corrosive environment contents
4. Combined effect of compressive stress
& corrosive environment (*) 1. Drawing number (*)
2. Date of dispatch
37. The flaring tool produces a flare of 3. Number of parts
4. All above is correct
1. 35°
3. The most commonly used synthetic
2. 35° to 45°
material for making flexible hose is
3. 30° to 37°
4. 35° to 37° 1. Buna – N
2. Butyl
38. Bolts are inspected 3. Both 1 & 2 are wrong
4. Teflon (*)
1. Magnetically
2. Zyglo 4. Hollow reamers are also called
3. As (1) & fluor4escent
4. All above is correct (*) 1. Fluted chucking reamer
2. Shell reamer (*)
39. The place where external tension loads 3. Jobbers reamer
are to be affected 4. None of the above is correct

1. Use clevis bolts 5. Which statement is correct

2. Use eye bolts (*)
3. Use close tolerance bolt 1. Single thread lead equal to the pitch (*)
4. Both 2 & 3 are correct 2. In double thread, pitch is double of the
lead
3. In triple thread, pitch is triple of the lead

CORRECT ANSWER IS MARKED * AT END 116

 REVISED OBJECTIVE QUESTIONS & ANSWERS

4. Both 2 & 3 are correct 3. Rock wax

4. Resin
6. During spark test of nickel, which color
of spark will produce 13. The minimum radius that can be
measured by filler gauge is
1. Orange
2. White (*) 1. 3/64"
3. Red 2. 1/64" (*)
4. Straw yellow 3. 1/32" – ¼"
4. 1/16"
7. Function of disintegrator is to
14. Accuracy of square gauge can be
1. Make hole without producing chips checked by
2. Make hole of any shape
3. As in 1 & 2 & also make hole in any kind 1. V – block (*)
of material 2. Jevel protector
4. Check the accuracy of surface plate
15. What is the function of ratchet step in
8. Mark the wrong statement micrometer

1. For insite check, the penetrate dye 1. Prevent turning of the thimble
process is useful 2. Prevent the use of too much pressure
2. Crack is indicated by a red stain termed 3. As in (2) & prevent further turning of the
by the dye in case penetrate dye thimble after correct pressure has
process applied (*)
3. Radiographic inspection is not suitable 4. All above correct
for surface crack (*)
4. The eddy current inspection offers 16. If a micrometer having negative error
improved sensitivity as compared other then the amount of error
NDT best
1. Must be added to the final reading (*)
9. The function of torch tip is to control 2. Must be subtracted from the final
the reading
3. Must be corrected before taking any
1. Amount of heat other reading
2. Flow of gases 4. Both 2 & 3 are correct
3. Both 1 & 2 are correct (*)
4. All above wrong 17. Precision instruments are normally
made of
10. Galvanizing is the process of coating
zinc is normally carried out on 1. Tempered steel
2. Hemonic metal
1. Al-alloy 3. Nichrome steel or Inver steel (*)
2. Iron & steel 4. Stallite
3. Steel parts (*)
4. Mag-alloy 18. In pentad

11. Mark the correct statement 1. Screen grid is placed between

suppressor grid & control grid (*)
1. Double cut means two different strokes 2. Control grid is placed between
at angle opposite to each other (*) suppressor grid & screen grid
2. Second cut is line medium smoothness 3. Suppressor grid is placed in between
3. Double cut & second cut is same control grid & screen grid
4. All above is correct 4. There is no suppressor grid

12. Name the kind of flux used with 19. Zener diode are used for
soldering the brass
1. Voltage regulation
1. Zinc chloride (*) 2. Some times called break down diode
2. Zinc carbide 3. Both 1 & 2 are correct (*)

115 CORRECT ANSWER IS MARKED * AT END

REVISED OBJECTIVE QUESTIONS & ANSWERS

4. Converting ac into dc with mechanical 2. Fatigue cracks give sharp clear pattern
aid 3. Fatigue cracks are normally found on
L/G torsion link legs attachment point
20. Voltage induced by generator is 4. All of the above is correct (*)
maximum when loop is
4. Intergranular corrosion occurs due to
1. Perpendicular to the lines of force
2. Parallel to the lines of force (*) 1. Lack of uniformity in the alloy structure
3. Coming away from lines of force 2. As in (1) & is difficult to detect in its
4. Going towards the line of force original state (*)
3. Combine effect of tensile stress &
21. A two pole alternation having 1800 rpm corrosive environment
has frequency of
5. Mark the correct statement
1. 60 cps 1. As length increases for a given size of
2. 120 cps wire the resistance increase
3. 30 cps (*) 2. As size of wire increase for a given wire
4. 90 cps length resistance decrease
3. As size of wire decrease for a given wire
22. Inverter are producing current at length resistance decrease
frequency of 4. Only 3 is wrong (*)

1. 300 cps 6. A resistor if second color land is brown

2. 400 cps (*) then
3. 200 cps
4. 450 cps 1. It will indicate the age of tolerance of
brown
23. Ball bearing can take 2. It will indicate the ohmic value of brown
(*)
1. Radial load only 3. No tolerance
2. Axial load only 4. It will indicate the number of zero to be
3. Both radial & axial load (*) added
4. It takes thrust only load
7. Fuses are normally made up of metal
GENERAL PAPER – 1991 having low melting point statement is
rue
1. ATA 100 specificatio9ns chapter 31
indicating 1. Low melting point material is alloy of tin
& bismuth
1. Ice & rain protector 2. If fuses made of copper than it is called
2. Indicating & recording (*) current limiter
3. Landing gear 3. As 1 & 2 & fuses are installed in the
4. Flight controls circuit so that all the current must pass
through it
2. Circular magnetization is used for 4. All the above is correct (*)

1. Detecting cracks running perpendicular 8. Micro switches are mostly used in a/c,
to the axis of the part making contact open or close
2. Detecting cracks running parallel to the movement is about
axis of the part (*)
3. Detecting cracks which is al. angle to 1. 1/8 inch or less
the axis of the part 2. 1/6 inch or less
4. 2 & 3 are correct 3. 1/16 inch or less (*)
4. ¼ inch or less
3. Mark the correct statement
9. Which equation is used to find out
1. Fatigue cracks are normally formed on capacitive reactance
parts that are in services but not on new
parts 1. Xc = 2 πfc

CORRECT ANSWER IS MARKED * AT END 116

 REVISED OBJECTIVE QUESTIONS & ANSWERS

2. Xc = ½ πfc (*) 2. The process in which the parts are

3. Xc = 2 π/fc magnetized out the magnetic power
used in select the flow is fluorescent
4. Xc = ¼ πfc 3. As in (2) & will glow under black light (*)
4. All are wrong
10. The minimum thickness which can be
measured by fealer gage is 16. In lead acid battery the positive plate &
the negative plate is made up of
1. 0.0020 inch
2. 0.0015 inch (*) 1. Positive plate is made up of lead while
3. 0.015 inch negative plate is made up of lead
4. 0.001 inch sulphate
2. Positive plate is made up of lead while
11. Steel containing 0.7 to 2% carbon is negative plate is made up of lead
known as peroxide
3. Positive plate is made up of lead
1. Plain carbon steel peroxide while negative plate is made
2. Medium carbon steel up of sulphate
3. High carbon steel 4. Negative plate is made up of lead
4. Cast iron (*) peroxide while positive plate is made up
of sulphate
12. Which statement is correct for flame
hardening 17. Match the following
1. Normally carried out in shafts, chains TITANIUM BEARING GEAR
2. Normally carried on parts where only a 1. Ni-Cr steel Non – magnetic Teeth
portion is required to be hard (*) 2. Teeth Ni – Cr Non – magnetic
3. The main disadvantage of this method is 3. Non – magnetic Ni – Cr Teeth (*)
that the time required for the is much 4. Teeth Ni – Cr Non – magnetic
more
4. All are correct 18. During carburizing which gas is
emitted
13. Which statement is correct in case of
introducing hardening 1. Carbon di oxide
2. Carbon mono oxide (*)
1. Heating the metallic substance by 3. Carbon tetra chloride
means of alternating magnetic field 4. None above correct
2. The depth of the case depends upon
frequency intensity of the em field but 19. Cold water quenching is normally
not on time period carried out for the parts produced from
3. With this method property of core
material is not affected 1. Tubing
4. All are correct (*) 2. Forging
3. Extrusion
14. Which statement is true regarding 4. All above is correct (*)
titanium
20. Arrange the metals are put their
1. Ti is approx. 70% heavier than Al & 50% increasing order of conductivity
lighter than stainless steel
2. Fatigue resistance of Ti is greater than 1. Iron < Al < Nl < Cu
Al & less than steel 2. Al < Iron < Ni < Cu
3. Corrosion of Ti is uniform 3. Iron < Ni < Al < Cu (*)
4. Both 1 & 2 are correct (*) 4. Iron < Ni < Cu < Al
15. Magnetic is 21. In instrument range marking a yellow
color indicates
1. The process in which the parts are
magnetized 1. Permission limit
2. Cautionary range & take off range (*)
3. Operation permissible for few time

115 CORRECT ANSWER IS MARKED * AT END

REVISED OBJECTIVE QUESTIONS & ANSWERS

4. Operation with certain precautions 2. Cam lock

3. DZUS
22. Mark the correct statement 4. Both 2 & 3 are correct (*)

1. Instrument panels are normally made f 29. Mark the wrong statement
non-ferrous material
2. Panels are usually shock mounted to 1. Helicoils are made of 18 – 8 stainless
absorb low frequency, high amplitude steel
shocks 2. Screws comes in AN 500 NAS 200
3. No. of shock mount used are depend on series
length of the unit 3. Dia of nut is measured in 16th of an inch
4. All are the correct (*) 4. Lockwashers should be used only with
secondary structure not with present (*)
23. Nickel alloy chisels are normally
sharpened by 30. A/C bolts having two dash on its head
indicating
1. Grinder
2. Filling (slowly to avoid sparking) 1. Corrosion resistant
3. Both 1 & 2 are correct 2. Al-alloy
4. Cannot be sharpened 3. 2024 bolts
4. Both 2 & 3 are correct (*)
24. Screw driver can be classified
according to its 31. Corrosion on Mg-alloy is indicating

1. Shape 1. White spots (*)

2. Type of blade (*) 2. Green spots
3. As 1 & blade length 3. Blueish spots
4. Both 2 & 3 are correct 4. Yellow spots

25. In gas welding of oxygen & acetylene 32. Solution heat treatment & then cold
regulators has worked is indicated by

1. Left hand thread & right hand thread 1. T2

respectively (*)
2. Right hand thread & left hand thread
2. T3 (*)
respectively 3. T4
3. Both have left hand thread 4. T5
4. Both have right hand thread
33. Match the following
26. Pull through rivets are fabricated in two
common head styles 1. Electron A – Al
2. Alduminium B – Mg
1. Universal head / protruding head 3. Duralumin C – Al
2. Brazier head 4. Al clad D – Al
3. 100 countershunk head
4. Both 1 & 3 are correct (*) 1. 1 – A, 2 – D, 3 – C, 4–B
2. 1 – B, 2 – D, 3 – C, 4–A
27. A rivet head having raised cross 3. 1 – C, 2 – D, 3 – A, 4–B
indicating 4. 1 – D, 2 – C, 3 – A, 4–B

1. 5056 T (*) 34. In brinell tester dia of the ball is

2. 2024 T
3. Carbon steel 1. 10 mm & apply pressure of 8000 kg for
4. Corrosive resistant steel ferrous metal
2. 0.3937 inch & apply pressure of 8000 kg
28. Which turn lock fastener contains stud for ferrous metal
assembly grammet & receptacle 3. 10 mm & apply pressure of 500 kg for
non-ferrous metal (*)
1. Air lock 4. All are correct

CORRECT ANSWER IS MARKED * AT END 116

 REVISED OBJECTIVE QUESTIONS & ANSWERS

2. Cadmium plated low carbon steel

35. In case of torque wrench, the 3. Corrosion resistant steel
4. Both 2 & 3 are correct (*)
1. The basic formula for use with extension
is Tw = Tex A/B (*) 42. Mark the correct statement
2. The basic formula for use with extension
is Tw = Twx A/B 1. Parker – kalon Z – type sheet metal
3. The basic formula for use with extension screw is a self tapping screw
is Tw = Twx B/A 2. Parker – kalon Z – type sheet metal
4. The basic formula for use with extension screw are blunt on the end
is Tw / Twx B/A 3. As in 2 nad are normally used for
temporary attachment
36. Lock bolts are normally used for 4. All are correct (*)

1. L/G, fitting, fuel line fitting 43. Cotter pins are normally made of
2. Primary controls
3. Wing splice fitting, skin splice plates 1. Cadmium plated high carbon steel
longerons 2. Cadmium plated low carbon steel
4. Both 1 & 3 are correct (*) 3. Corrosion resistant steel
4. Both 2 & 3 are correct (*)
37. The most commonly used composite
material is 44. How much thread should be exposed
after lightening the turn buckles
1. Kevlar
2. Carbon / graphite (*) 1. Atleast three threads
3. Fibre glass 2. Less than three threads
4. Boron 3. Not more than three threads (*)
4. Not less than three threads & not more
38. Buttress threads are normally used than five threads

1. Where a thread requiring great strength 45. In annealing parts most be cooled in
in one direction only
2. To vice, guns etc. 1. Still all
3. Where it is necessary for transmitting 2. Furnance (*)
power in either direction 3. Brine
4. Only 3 is wrong (*) 4. Oil

39. In transition fit 46. Mark the correct statement

1. Shaft is longer than the hole 1. Impact resistance decreases as metal

2. Shaft is smaller than the hole goes softer & softer & vice
3. Shaft & the hole are approx of same 2. Impact resistance increases as metal
size goes softer & softer & vice
4. All the wrong 3. Impact resistance increase as metal
goes harder & harder & vice
40. There is a difference between AN & AN 4. Impact resistance decrease as metal
fitting which is correct goes harder & harder & vice
5. 2 & d are correct (*)
1. AN has gray color while AC has yellow
color 47. Which formula is used for calculating
2. AN has the gray color while AC has the the inside dia of an internal gear
blue color
3. AN is longer while AC is shorter (*) 1. Ng – Np/2c
4. As inm 2 & AM has 35° angle & AC has 2. N – 2/DP (*)
37° angle 3. PD – 2/DP
4. Ng – Np/2p
41. Cotter pins are normally made of 5. Ng – Np/DP

1. Cadmium plated high carbon steel 48. Trammel is also called

115 CORRECT ANSWER IS MARKED * AT END

REVISED OBJECTIVE QUESTIONS & ANSWERS

1. Circle maker 1. A fine Al screen may be laminated

2. Divider under the top layer of fabric dissipate
3. Beam compass (*) electrical charge.
4. Both 2 & 3 are correct 2. Microballons are mixed with regin to
add strength (*)
49. When thimble makes one complete 3. PVC can be cut with a hot wire cutter
revolution it moves on the sleeve 4. Tedlar is a layer of plastic coating which
serves as an addition moisture barrier.
1. 0.40 inch
2. 0.25 inch 57. Variation in uniformity on the
3. 0.025 inch (*) cylindrical surface can be checked by
4. 0.0025 inch
1. DTI (*)
50. Surface plate is made of 2. Center square
3. Square gage
1. Cast 4. Hermphrodite caliper
2. Granite
3. Nimonic alloy 58. Mark the correct statement
4. Both 1 & 2 are correct (*)
1. Letter A on the drill indicated smallest
51. Vice can be classified according to size while letter Z indicated the largest
size (*)
1. Reference number (*) 2. Letter Z on the drill indicated smallest
2. Length of the jaw size while letter A indicate the largest
3. Weight of the vice size
4. Both 1 & 2 are correct 3. The algebric difference between main
limit and the basic size is low as lower
52. Parcoluburizing is carried out on deviation
4. Both 2 & 3 are correct
1. Iron & steel (*)
2. Mg-alloy 59. The pressure angle of a gear teeth is
3. Al-alloy
4. All above the wrong 1. The angle between the tangent to the
pitch circle & the perp line the contact
53. Kelvar is identified by it's point of the gear teeth (*)
2. The angle between tangent to the line
1. Black color of contact perp to the pitch circle
2. Yellow color (*) 3. The angle between the line perp to the
3. White glaming color pitch circle & line of contact
4. Brown color 4. All the wrong (*)

54. Thread running at 45° from warp is 60. The binary equivalent of 29 is
known as
1. 11101 (*)
1. Weft 2. 10101
2. Bias (*) 3. 10011
3. Selvage edge 4. 11111
4. None of the above
61. An altimeter consist of
55. MEK is used
1. Two aneroid capsule
1. For cleaning dust, grease from 2. Pressure cutting knob for adjusting
composite component (*) barometric pressure
2. For cleaning all parts 3. Three aneroid capsule
3. For cleaning any parts 4. All of the above (*)
4. For cleaning electrical equipment
62. An altimeter consist of
56. Mark the incorrect choice
1. Two aneroid capsule

CORRECT ANSWER IS MARKED * AT END 116

 REVISED OBJECTIVE QUESTIONS & ANSWERS

2. Pressure cutting knob for adjusting 2. 0.002 mm

barometric pressure 3. 0.02 mm (*)
3. Three aneroid capsule 4. 0.009 cm
4. All of the above is correct (*)
7. In vernier macrometer 9 parts of main
63. Most headless notch screws are turned scale is divided into 10 parts of vernier
by scale the main scale has the
graduations of 1 mm find the length
1. Screw driver count.
2. Phillips screw driver
3. Internal screw driver 1. 0.01 cm
4. Allen wrentch (*) 2. 0.001 cm
3. 0.09 mm (*)
SEPTEMBER 1994 4. 0.009 mm

1. Aviation snaps are used on 8. SCR is

1. Heat treated Al alloy sheet (*) 1. Four junction diode

2. Stain steel 2. Three junction diode
3. Fibre 3. Two junction forward biased with one
4. All of the above reverse biased
4. 2 & 3 are correct (*)
2. Soldering used for electrical
connections has the MP range 9. The triode consists of

1. 100 degree to 200 degree C (*) 1. Anode, grid, heater

2. 100 to 300 degree 2. Plate, grid & heater
3. 300 – 600 degree C 3. Anode, plate, grid heater, & cathode
4. 200 – 300 degree C 4. Plate, cathode, heater & fine mesh of
wore between plate & cathode (*)
3. Helical grars are used for
10. The zenor diode
1. Transmit motion to shaft at an angle
2. Transmit motion to shaft which are 1. Is used as rectifier
perpendicular together 2. Is used for voltage regulation (*)
3. To carry larger load (*) 3. Is used for motor protection & in clippin
4. None of the above is correct circuit
4. Both 2 & 3 are correct
4. The heat conductor available during all
features in aircraft used is 11. Static vents in pitot static system are
located with
1. Copper
2. Aluminium 1. From at aluminate ice
3. Bras 2. To aluminate ice formation
4. Silver 3. To eliminate position error (*)
4. All of the above is correct
5. The most accurate system for drill size
is 12. Toflon hose is

1. Friction (1/16 inch – 3 & ½ inch) 1. High strength

2. 1/63 inch to 1/6 2. High temperature resistance
3. a to z letter system 3. 1 & 2 are correct (*)
4. No 80 to no 1 system (*) 4. None of the above is correct

6. In a vernier scale 24 division are equal 13. X-ray used in N.D.T. inspection
to 25 division of vernier scale, 1
centimeter of main scale is divided 20 1. Have short wave length high protecting
equal parts & the least count. power (*)
2. Have a long wave low protecting power
1. 0.001 cm 3. 1 & 2 are correct

115 CORRECT ANSWER IS MARKED * AT END

REVISED OBJECTIVE QUESTIONS & ANSWERS

4. None of the above otehr & supplied with same directing

AC.
14. The cause of buckling of sheet is
1. Both are attracted to each other (*)
1. Small hole (*) 2. Both are repelled
2. Long hole 3. Clockwise rotation
3. Hammering 4. Anticlockwise rotation
4. Heat
22. Which of the following has negative
15. The repair a crack the joint is to be coefficient of resistance
formed
1. Thermistor (*)
1. Lap joint 2. Transistor
2. Butt joint (*) 3. Semi conductor
3. Tea joint 4. Resistor
4. Corner joint
23. In a 4 stroke cycle the spark plug fires
16. To suit the welding torch for every

1. Cylinder vale should be closer first 1. 4 revolution of crank shaft

2. Accetelene cylinder valve is close first 2. 2 revolution of crank shaft (*)
(*) 3. 1 revolution of crank shaft
3. Both the close simultaneously 4. 360 degree revolution of crank shaft
4. Accetelene cylinder pressure is reduced
24. If a wire having a resistance of 9 ohm is
17. Hydrogen is given off increase its length twice, then new
resistance is
1. During all stages of battery servicing
2. When battery is over heated 1. 1 ohm
3. During charging operation of the battery 2. 8 ohm (*)
(*) 3. 6 ohm
4. During discharging operation of the 4. 4 ohm
battery
25. If resistor of 30 ohm are connect &
18. Magnesium is battery voltage is 2 v then a meter
reads
1. Susceptible to corrosion
2. Corrosion resistant & light weight 1. 1/10 A
3. High, tendency to crack 2. 3/10 A
4. 1 & 3 are correct (*) 3. 7/10 A
4. None of the above is correct (*)
19. When switch Mg is open voltmeter
indicator 1.5 v & when close indication 26. Identification of titanium
1.35 v current is lamp. What is the
internal resistant of battery: 1. Spark
2. Not standing & making in glass
1. 1 ohm 3. Acid best
2. 0.15 ohm (*) 4. Both 1 & 2 are correct (*)
3. 1.35 ohm
4. 1.50 ohm 27. In floroscent dye penetrant test the
colour of the light use in the part
20. The altemeter is checked by when inspected
barometer is not available
1. Green color in black light
1. Micromonometer 2. Green color in white light
2. Vacuum Chamber 3. Ultra violet in white light (*)
4. Red color in white light
21. The identical insulated wire coils are
hung from air to that the facing each 28. Mark the correct statement

CORRECT ANSWER IS MARKED * AT END 116

 REVISED OBJECTIVE QUESTIONS & ANSWERS

amp & secondary current is 90 amp the

1. Diode is used as a rectifier (*) step down transformer.
2. Tiode is used as a rectifier
3. Diode is used as a amplifier 1. 30
4. All of the above is correct 2. 40
3. 0
29. Cleaning of titanium surface 4. 90 efficiency (*)

1. Iron scrappers 36. Annealed metal is

2. Steel
3. Mild aspiration or hand plashed with 1. To soft
aluminium (*) 2. Low strength
4. All of the above is correct 3. Relieved internal stresses
4. All of the above is correct (*)
30. The NPN transistor
37. Barcol tested is used for
1. Flow of electrons from emitted to
collector 1. Steel
2. Holes move from collector to emitter 2. Al alloy
3. Flow of electron from base to emitter 3. Titanium
4. Flow of electron from emitter to base (*) 4. As in (2) & copper (*)

31. In triode grid 38. Rockwell tested measure

1. Controls the electron flow cathode to 1. Resistance to penetration (*)

plate (*) 2. Diameter of impression
2. Resource space charge 3. Size of identification
3. It increase admission of electrone from 4. None of the above is correct
cathode
4. Prevent secondary emission 39. PN Junction is used as

32. Al alloys are welded with 1. Rectifier (*)

2. Amplifier
1. Oxidizing flame 3. Oscillator
2. Reducing flame 4. None of the above is correct
3. Neutral flame (*)
4. Reducing flame but in first flame is 40. The CP of bavel gear is
neutral & then reduced
1. Teeth per inch
33. Brass & bronze are welded with 2. The distance from the center of one
teeth to another teeth measure pitch
1. Oxidizing flame circle (*)
2. Neutral flame 3. The distance from the centre one teeth
3. Reducing flame to center of next teeth
4. Reducing flame but first the flame is 4. None of the above is correct
neutral & then reduced
41. The binary expression for 296 is
34. The check interior surface condition of
cylinder & surface instrument used is 1. 101011101
2. 100101000 (*)
1. Boroscope 3. 111001100
2. Fluroscope 4. 110010111
3. Endoscope or introscope
4. All of the above is correct (*) 42. The nd of TPI are measured by

35. The primary is subjected to 220 v & 1. Screw pitch gauge (*)
secondary is step down to give an 2. SWG (Standard Wire Gage)
output of 11 v & primary circuit is 5 3. Thickness gauge
4. None of the above is correct

115 CORRECT ANSWER IS MARKED * AT END

REVISED OBJECTIVE QUESTIONS & ANSWERS

43. The output of an OR gate will be given

51. In purely inductive circuit the current
1. When all the input are energized
2. When all the inputs are zero 1. Lags behind the voltage by π/2 (*)
3. Anyone of the input is energized 2. Loads the voltage by II/1 Capacitive
4. 1 & 3 are correct (*) circuits
3. Is in phase with the voltage
44. Computer consist of 4. Legs behind the voltage by II/2 at high
frequency
1. Printer, decode, memory
2. Input, output, CPU (*) 52. The magnetude of the induced emf
3. Input, output, printer produced in all coil when a magnet is
4. None of the above is correct inserted in to it does not depend upon
the
45. The decimal number for 10111011101 is
1. No of turn in the coil
1. 1502 2. Reactance of the coil (*)
2. 1500 3. Magnetic moment of the magnet
3. 1501 (*) 4. Speed of the rotation of magnet
4. 1600
53. Chocks is used as resistance in
46. O-rings are checked for internal cracks practical inductive reactance in choke
by & transformer

1. 4 power magnifying glass 1. DC circuti

2. By rolling on inspection cone 2. AC circuit (*)
3. By rolling on inspection dowel 3. 1 & 2 are correct
4. All of the above is correct (*) 4. Full wave rectifier

47. Radiography depends on 54. Memory of computer are

1. Size of & shape 1. Rom, CPU, ALU

2. X-ray 2. Rom, Ram, Prom (*)
3. Thickness of material 3. ALU, Rom, Ram
4. All of the above is correct (*) 4. None of the above is correct

48. Bavel gears used for 55. Stress corrosion occurs main on

1. Transmission of loads for between 1. Magnesium alloy

surface at angles to ech other (*) 2. Aluminium alloy (*)
2. For a variation of speed 3. Stainless steel
3. In speed reading 4. Both 2 & 3 are correct
4. 1 & 3 are correct
56. Purpose of using flux in welding is
49. The DP in a gear indicates
1. To reduce oxidation
1. Number of teeth per inch 2. To provide flow to the molten metal
2. Size of gear teeth 3. To increase the bounding
3. Both 1 & 2 are correct (*) 4. All of he above are correct (*)
4. None of the above is correct
57. Optical instrument used to inspect the
50. In the case of AC circuits ohm's law interior structure of a component is
hold for
1. Fluroscope
1. Peak values of voltage & current 2. Foroscope
2. Effective value of voltage & current (*) 3. Indoscope
3. Instentenneous value of voltage & 4. All of the above is correct (*)
current
4. All of the above are correct

CORRECT ANSWER IS MARKED * AT END 116

 REVISED OBJECTIVE QUESTIONS & ANSWERS

58. The method of temper steel depends 2. 5 ohm (*)

upon 3. 7 ohm
4. 7/R ohm
1. Type of steel
2. Size of steel 66. The sketch 52 indicates
3. Density of steel
4. All of the above is correct (*) 1. All grains punch
2. Prick punch
59. In computers hard disk & floppy disk 3. Pin punch / drift punch
are 4. Concer punch

1. Different in used 67. The reading shown in micrometer is

2. Similar but hard disk can store more
than floppy disk (*) 1. 0.175 inch
3. Similar but hard disk can store less than 2. 0.175 inch
floppy disk 3. 1.65 inch
4. None of the above are correct 4. 1.35 inch

60. Indicates on the tools are 68. The transferring metal from one object
to another by chemical or electrical
1. Thread shank filler process is done to protect the base
2. Tap, cutter, pilot metal
3. Drill cutter
4. None of the above 1. Against corrosion
2. Increase strength to protect the base
61. The gage shown in the sketch used for metal against chemical reaction
checking 3. Wear
4. All of the above is correct (*)
1. Sheet on plate
2. Average terminate 69. To improve tensile strength, ductility &
3. Square shock resistance, magnesium casting
4. None of the above is correct are normally

62. Fretting corrosion normally 1. Case hardened

2. Solution heat treatment (*)
1. Occur around rivets in a skin 3. Precipetation heat treatment
2. Indicates by dart deposites 4. None of the above is correct
3. Occur in only molecules
4. 1 & 2 are correct (*) 70. Hydrogen is given off

63. The NDT check inspection is made in 1. In electrolyte

white light & dye used is 2. Lead acid battery
3. In over heated condition
1. Gray 4. After fully charged condition in Ni-cd
2. Red (*) battery (*)
3. Black
4. All are correct 71. As per ATA 100, identification of a/c
electrical cables, letter & size are
64. Composite material marked

1. Have reduced wear 1. In the middle

2. Do not corrode 2. Side by side (*)
3. Have high strength to weight ratio 3. Prefix & Suffix
4. All above are correct (*) 4. None of the above

65. An AC series circuit contains 4 ohms 72. In modern a/c most popular heat
resistance & 3 ohm inductive reactance treated aluminum alloy used in
what is the impedance of the circuit structural application

1. 1 ohm 1. Alloy 2024 (*)

115 CORRECT ANSWER IS MARKED * AT END

REVISED OBJECTIVE QUESTIONS & ANSWERS

2. Alloy 5054 3. Both are correct (*)

3. Alloy 5003 4. Artificial aging
4. Alloy 7075
80. In NDT inspection, performance of
73. A coil is helped with a plain horizontal magnetic particle inspection can not
to certain surface & a bar magnet is effect by
dropped vertically downward
1. Cadmium
1. The magnet will fall with constant 2. Copper
acceleration equal to 'G' 3. Tin & zinc
2. Constant acceleration greater than 'G' 4. All of the above is correct (*)
3. Constant acceleration less than 'G'
4. Non uniform acceleration less than 'G' 81. Which language is the business
(*) oriented language

74. The main control unit of computer is 1. Pascal

present in 2. Basic
3. Fortran
1. VDU 4. Cobol (*)
2. CPU (*)
3. Keyboard 82. The third generation computer
4. Hard disk
1. Integrated circuit are used
75. While treating for magnetic testing it 2. Microprocessor are used (*)
was found non magnetic, in nitric acid 3. Semi transistor
it was found rapid action, greenish 4. All of the above is correct
blue
83. The unit of the memory is
1. Nickel steel (*)
2. 18 – 8 steel 1. Bite
3. Monel 2. Bits
4. CRS 3. Nibbles
4. All of the above is correct (*)
76. Analog computer is
84. Explain the ??? basic
1. More correct than digital computer
2. Less accurate than digital computer (*) 1. Beginners all purpose symbol i.e.
3. Both 1 & 2 are correct instruction code
4. None of the above
85. The principle local carrying member
77. In computer machine language is in a composite structure is

1 High level language 1. Fibres (*)

2 Low level language (*) 2. Matrix
3 Very high level language 3. Adhesive
4 None of the above is correct 4. Rasin

78. Decimal equivalent to binary number 86. Intraply hybrid composites means
110 is
1. Inforcing material of same fibre in
1. 2 different layers
2. 3 2. Reinforcing material woven from two
3. 6 (*) more fibre types (*)
4. 9 3. Reinforcing material different indifferent
layer
79. Aluminium alloy can be heat-treated 4. None of the above is correct

1. Solution heat treatment 87. Metal matrix composite is a recent

2. Precipitation heat treatment composite material where in

CORRECT ANSWER IS MARKED * AT END 116

 REVISED OBJECTIVE QUESTIONS & ANSWERS

94. For high Al alloy the more suitable

1. Resin in reinforced with metal welding is
2. Resin & fibre & reinforced with metal
3. Fibre are reinforced with metal during 1. Seam welding
melton stage 2. Spot welding or butt welding (*)
4. All of the above is correct (*) 3. Electric resistance welding
4. All of the above is correct
88. Replacement of honey comb core
segment to the existing honey done 95. The measure skin thickness of hollow
with help of tubular member is normally done by

1. Film form adhesive (*) 1. By distructing the tube

2. Freeing adhesive 2. By micrometer tube (*)
3. Epoxy resin with fibre 3. Eddy current
4. All of the above are correct
96. The NDT radiography method the
89. Two wires each a meter long are kept density means
at a distance of 0.02 & 16.2 ampire
current is flowing through each wire, 1. Degree of blackness (*)
then force the wire will be
97. The computer mark the storage
1. Attractive if the direction of the current device
flowing through (*)
2. Repulsive if direction of current will be 1. VDU
same 2. Printer
3. Mouse
90. In computer memory store measured 4. Floppy disk (*)
by
98. Expand the term Ram while loss the
1. Byte / bit (*) term 'Ram" means
2. Power
3. Both 1 & 2 1. Random access memory (*)
4. None of the above is correct
99. A lead acid cell contains
91. The thickness of conducting & non
conducting is done by 1. Positive plates cooted with lead
aproxide
1. Micrometer 2. Liquid electrolyte consists of the
2. Eddy current (*) sulphate & water
3. Ultrasound 3. Negative plate made of lead
4. Caliper 4. Both 1 & 3 are correct (*)

92. Evidence of corrosion on copper is 100. Mark the correct statement is

indicated by
1. AND gate is one whose output is
1. Red spot on the surface steel energized when all energized
2. Green spot in the surface (*) 2. OR gate is one whose output is
3. Grey spot on the surface energized when more of the energized
4. None of the above is correct (*)
3. A gate is a logic circuit with one input
93. Evidence of corrosion on Al, alloy is are many output
indicated by 4. All of the above is correct

1. More shining portion near the surface 101. In a double thread screw
area
2. Grey spot 1. Pitch is twice the load
3. Pitting on surface 2. Load is twice the pitch
4. Power form (*) 3. Lead is twice the pitch (*)
5. All of the above is correct 4. Thread depth is measured parallel to the

115 CORRECT ANSWER IS MARKED * AT END

REVISED OBJECTIVE QUESTIONS & ANSWERS

102. Indication for the dull drilline is 3. 1.5 ohm (*)

4. None of the above is correct
1. Rough finished hole
2. High temp of the drill 109. A torch bulb when cold has 1 A
3. Low drilling speed current, it draws a current when
4. All of the above is correct (*) growing from a source of 3 v, the
resistance of bulb is
103. In NDT magnetic particle inspection
cannot be done if the coating of 1. 5
2. 10
1. Copper 3. 6
2. Tin 4. 8
3. Nickel & chromium (*)
4. Zinc 110. In a electron magnetic induction unit
of magnetic flux is
104. In inspection of a material in non
magnetic, nitric & rapid action shows 1 Weber (*)
greenish blue mark side for 2 Ampere x meter
3 Newton / meter
1. Carbon steel magnetic 4 Newton
2. Nickel steel (*)
3. Monel 111. Mark the correct statement is
4. 18 – 8 steel
1. Rheostat is a variable resister used to
105. One micron is vary amount of the circuit (*)
2. Potential meter is a variable resister
1. 10 cm used to vary amount in the circuit
2. 1.0 cm 3. Potentiometer has two terminals
3. 10 mm 4. None of the above are correct
4. All of the above is correct
112. When 2 conductor of 1 mt in length
106. In a vernier caliper, there are 10 carrying a current at 2 amp are .025
clivisons on the vernier on the main meter a part from each other
scale is divided in 10 parts while
measuring in zero of the vernier lies 1. Conductor carrying current in the same
should of 1.8 cm & 4th division direction will attract (*)
coinsided with a main scale division 2. Conductor carrying current in the
the length is opposite direction will attract
3. No effect
1. 1.84 cm 4. None of the above is correct
2. 1.04 cm
3. 1.86 cm 113. Unix is the

107. When the plate current is 16 amp, the 1. Double operating unit (*)
number of electron flows 2. CAD & record of engineering
organization
1. 10 – 8 electron / sec 3. None of the above is correct
2. 10 ?? electron / sec
3. 10 electron / sec 114. The most powerful computer is
4. None of the above is correct
1. Micro computer
108. Six equal resistance of 1 ohm each 2. Super computer (*)
are connects in a circuit ABCDEF, the 3. Mini computer
resistance offered by the 4. Laptop computer
combination, if the current A & leaves
at B is: 115. Matrix is used to

1. 2.5 ohm 1. Transfer stress to fibre (*)

2. 3 ohm 2. Take stress from the fibre

CORRECT ANSWER IS MARKED * AT END 116

 REVISED OBJECTIVE QUESTIONS & ANSWERS

3. Increase the hardness of adhesive 4. 70%

4. None of the above is correct
125. In a given circuit 1.4 A current flowing
116. Catalyst in a composite acts as from point A. what is the current at
point B
1. Hardener (*)
2. Curing agent 1. a.4 A
3. To increase the property of resin 2. 1.0
4. None of the above is correct 3. .6 A
4. 1.2 A
117. The used of grid in a triode is
126. EDP stands for in computer
1. To reduce space charge region
2. To control the electron flow between the 1. Electrical data processing
cathode, & the anode 2. Electronic data processing (*)
3. None of the above is correct 3. Entry data processing
4. 1 & 2 are correct (*) 4. Electronic discrete program

118. The semi conductor having high 127. Electronic digital computer
negative co-efficient is
1. Mathematical calculation
1. Thermister (*) 2. Data processing
3. Stress data in given instruction
119. DP indicates in a gear for 4. All of the above are correct (*)

1. Distance between two teeth 128. (010100)2 convert into octal

2. Height of the teeth
3. Pitch circle 1. (24)8
4. None of the above are correct (*)
2. (15)8
120. Diode triode or transistor works on 3. (26)8
4. (50)8
1. Ohm's law
2. Do not obey ohm's law (*) 129. Fillers is

121. Change 1010101 in decimal 1. Epoxy

2. Cellulose (*)
1. 85 (*) 3. Polyester
2. .65 4. Boron
3. .111
4. None of the above is correct 130. Which statement is true for leveling

122. PN junction is knows as 1. Leveling of large a/c is critical than

lighter a/c (*)
1. Forward bios (*) 2. Leveling is done normally on longitudinal
2. Reverse bios axis
3. Leveling is done more accurate on
123. Counter sunk rivet: lighteral axis
4. None of the above is correct
1. When riveting different layers of sheets
131. The difference between digital &
124. In a step down transformer the input analog computer
voltage is 220 v & current 5 A & the
output voltage is 11v & the current is 1. Analog computer has large memory
90 A, the calculate the efficiency of 2. Digital compute cost more & in
the transformer comparatively difficult to program
3. Analog computer is less accurate (*)
1. 30% 4. 2 & 3 are correct
2. 90% (*)
3. 60%

115 CORRECT ANSWER IS MARKED * AT END

REVISED OBJECTIVE QUESTIONS & ANSWERS

132. Excess size of computer depends 3. Low permeability of ferro magnetic

upon substance
4. Both 1 & 2 are correct (*)
1. Software used
2. Frequency & signal received 139. A computer stored instruction in
3. To software & hardware both
4. Hardware (*) 1. English language
2. Decimal number system
133. The greatest memory of which device 3. Octal number system
4. Binary number system (*)
1. Winchester type device disks (*)
2. Tape type recording instrument 140. An input unit of a computer
3. Floppy disk unit communicate
4. None of the above is correct
1. Between operate and computer (*)
134. Which are related to the memory 2. Between memory with printer
3. Between cpu with monitor
1. Hard disk (*) 4. Between output and computer
2. Keyboard
3. CD – Rom 141. For jacking the a/c
4. Monitor
1. Normally the jack points are given in all
135. If twist drill is not printed clearly, it a/c
can be checked by 2. Three points on a/c for jacking is
provided to stabilize the a/c about three
1. Drill size gauge number system on left & points
fraction system on right 3. Jacking points are located in relation to
2. Drill size gauge with number system on CG position
right fraction on left 4. All the above are correct (*)
3. SWG
4. By micrometer (*) 142. In ATA specification the electrical
cable number is instructed as
136. Mark correct statement
1. Prefix suffix
1. A transistor connected in common base 2. In iddle
configuration has a low input resistance 3. Side & side
& high output resistance 4. All of the above are correct
2. At transmeter connected in common
emitter configuration a medium input 143. Thread in deep holes are cut by
resistance & a output resistance
3. The input & output signals of a 1. Extension tap (*)
common emitter are out of phase 2. Round split die
4. All the above are correct 3. Bottoming tap
4. 1 & 3 are correct
137. The arrow head on the transistor
symbol always pointing the direction 144. Size of flat cold chisel is identified by
of
1. Length of cutting edge
1. Hole flow (*) 2. Width of cutting edge (*)
2. Electron flow 3. Weight of the chisel
3. Electrons are the majority carrier 4. All of the above are correct
4. Holes are the majority carrier
145. Mark the correct statement
138. The energy loss in a transformer is
due to 1. Corrosion on carbon steel is in form of
brown, red color (*)
1. Heating the coils 2. Corrosion on CBS in sheets dimeling is
2. Eddy current in the core the necessary

CORRECT ANSWER IS MARKED * AT END 116

 REVISED OBJECTIVE QUESTIONS & ANSWERS

OCTOBER / SEPTEMBER 1996 7. Voltage drop across a conductor of

known resistance depends on
1. In transformers, mark the correct
statement 1. Current flowing inside the current
2. Voltage of circuit
1. If any of windwings are shorted, it is 3. The amount of thickness of wire
easy to detect by measuring resistance insulation (*)
2. In case if shorted windwing, the
transformer becomes hot 8. E – glass is
3. If there is shorted windwing, the output
voltage will be very high 1. Also known as electric glass
4. Both 2 & 1 are correct (*) 2. Also known as borosilicate glass
3. Has low strength & weight ratio
2. If the frequency of the primary voltage 4. All of the above is correct (*)
of a transformer is increased from 50
Hz to 60 Hz, keeping peak voltage INDIAN INSTITUTE OF AERONAUTICS
same, the voltage in the secondary will
COMPUTERS
1. Increase by a factor of 60/50
2. Increased by a factor of 50/60 1. A computer in a / an
3. Be unpredictable for want of sufficient
data
4. Not change (*) 1. Mechanical device
2. Electrical device
3. 'n' identical cells, each of the emf E & 3. Electronic device (*)
internal resistance r, are connected in 4. Electromechanical device
series to form closed circuit. an ideal
voltmeter connected across 'n' cells 2. A 'Flow chart" is a
will be
1. Step wise representation of a
1. NE (*) programme
2. Zero 2. A systematic pictorial representation of
3. (n – N)E a programme
4. N (1 – N/n) E 3. Is a kind of programme written in high
level language
4. Very high insulation resistance of 4. Either 1 & 2 are correct (*)
electric cable is measured by
1. Meggar (*) 3. A digital computer can be operated
2. High range ohm meter with
3. Ammeter
4. Voltameter 1. Only numerical data (*)
2. Only non numerical data
5. When batteries are connected in 3. Both numerical & non numerical data
parallel 4. Neither numerical nor non numerical
data
1. Voltage increases, capacity remains the
same 4. Algorithm is a
2. Voltage remains same but capacity
increases (*) 1. Pictorial representation of a programme
3. Voltage depends upon plate area 2. A stepwise systematic representation of
4. No effect on either powder or voltage a programme (*)
3. High level language to represent a
6. To increase the voltage of battery programme systematically
4. Assembly language to represent a
1. Cells are connected in series (*) programme systematically
2. Cells are connected in parallel
3. Plates are connected in series 5. The most powerful of the following:
4. Electrode area is increased
1. Minicomputer
2. Microcomputer

115 CORRECT ANSWER IS MARKED * AT END

REVISED OBJECTIVE QUESTIONS & ANSWERS

3. Mainframe 12. Find the odd man out

4. Supercomputer (*)
1. ALU, Memory, Counters
6. Main difference between PC / ATI & PC / 2. CU, Floppy disket, registers (*)
XT are 3. Control unit, MPU
4. ALU, auxiliary memory
1. PC / AT has much more memory than
PC/XT 13. The CPU of the 4th generation computer
2. PC/AT has much more speed than is
PC/XT
3. PC/AT has multi terminal facility & 1. An IC chip using VLSI technology
PC/XT has only single terminal facility 2. Microprocessor
4. PC/XT has multi terminal facility & 3. Both 1 & 2 are correct (*)
PC/AT has single terminal facility (*) 4. None of the above is correct

7. Binary equivalent of 0.625 14. INTEL is a company involved in the

manufacturing of
1. 0.010102
2. (0.101)2 1. Printers
3. 0.11002 2. Storage devices
3. IC Chip
4. 0.010112
4. All of the above is correct (*)
8. If the inputs of a gate are A & B & its 15. Bill gates is the chairman of
output is A + B the gate is
1. IBM
1. OR gate (*) 2. Microsoft (*)
2. AND gate 3. Intel
3. X-OR gate 4. Motorola
4. X-NOR gate
16. The company Microsoft is involved in
9. The given truth table is for
1. Making of computer hardware
A B C 2. Making of computer software
1 1 1 3. Both 1 & 2 are correct (*)
0 0 1 4. None of the above are correct
0 1 0
1 0 0 17. The fastest of the following is
1. XOR gate 1. 80286 processor
2. XNOR gate (*) 2. 80386 processor
3. NAND gate 3. 80436 processor
4. OR gate 4. Pentium processor (*)
10. 2 complement of the binary digit is 18. The main memory of the computer is
1. 01 (*) 1. RAM
2. 1 2. ROM
3. 10 3. Hard disk (*)
4. 0 4. CD
11. XOR gate is 19. RAM is
1. A parallel switching circuit with exclude 1. Volatile semiconductor memory
condition (*) 2. Read/write memory
2. Series switching circuit with exclude 3. Random access memory
condition 4. All of the above are correct (*)
3. Parallel switching circuit
4. Series switching circuit 20. ROM is

CORRECT ANSWER IS MARKED * AT END 116

 REVISED OBJECTIVE QUESTIONS & ANSWERS

1. 8 bits
1. Read memory (*) 2. 4 bits (*)
2. Write memory 3. 2 bits
3. Both 1 & 2 are correct 4. 16 bits
4. None of the above are correct
29. The fastest component of the computer
21. EPROM can be erased by is

1. Sodium light 1. CPU (*)

2. uv rays 2. Computer memory
3. Electrical pulses 3. Storage devices
4. Either UV rays or electrical pulses 4. Input / Output devices

22. The fastest memory of the following 30. Locate the odd man out

1. RAM 1. Hard disk

2. ROM 2. Floppy disk
3. Cache 3. Magnetic tape
4. Hard disk 4. Compatt disk

23. The main memory of a computer is 31. Compact disk is a

located in
1. Semi conductor device
1. The hard disc (*) 2. Magnetic device
2. Compact disk 3. Optical device (*)
3. Floppy disk 4. None of the above are correct
4. None of the above are correct
32. Locate the odd man out
24. ROM is
1. OBR
1. Volatile semi conductor memory 2. OMR (*)
2. Non volatile semi conductor memory (*) 3. OCR
3. Magnetic memory 4. MICR
4. All of the above are correct
33. Floppy diskett is a
25. The processing of the CPU is in the
order of 1. EPROM
2. RAM
1. Millisecond 3. EEPROM
2. Microsecond 4. Flexible storage media (*)
3. Nanosecond (*)
4. Megasecond 34. The slowest of the following is

26. DRGM is 1. Hard disk

2. Floppy disk (*)
1. Semi conductor memory 3. CD
2. Volatile memory 4. Magnetic tape
3. Has to be coefficiated with the data
after a certain interval of time 35. CDROM is released by
4. All of the above are correct
1. ---
27. 1 KB is equal to 2. Infrared light (*)
3. Electrical package
1. 1000 bytes (*) 4. By appropriate programming only
2. 2 bytes
3. 1000 MB 36. Modem is an
4. None of the above are correct
1. Input device
28. A nibble is equal to 2. Output device
3. Input / Output device (*)

115 CORRECT ANSWER IS MARKED * AT END

REVISED OBJECTIVE QUESTIONS & ANSWERS

4. None of the above are correct

45. Locate the odd man out
37. Locate the odd man out
1. Light pen
1. Dot matrix printer 2. Plotter (*)
2. Inkjet printer 3. Mouse
3. Chain printer 4. Joystick
4. Drum printer (*)
46. The 'Printed document" in computer
38. Optical scanner is a terminology is termed as

1. Input device (*) 1. Soft copy

2. Output device 2. Hard copy (*)
3. Input / output device 3. Firm copy
4. None of the above are correct 4. Live copy

39. A software is a 47. The display of MONITOR of a computer

system is mostly
1. Set of programmes
2. Set of instructions 1. Semi conductor display
3. All of the above are correct (*) 2. LED type display (*)
4. None of the above are correct 3. LCD type display
4. Electron beam type
40. Disk operating system is
48. Choose the correct statement among
1. A system software the following
2. Software environment
3. Software utility package 1. Line printer is non impact printer
4. A high level language 2. LASER printer is a non impact printer (*)
3. DOT matrix printer is non impact printer
41. Computer virus is a 4. Character printer is faster than line
printer
1. Software programme (*)
2. Hardware programme 49. Printer is connected through
3. Machine language
4. Assembly language 1. Parallel port
2. Serial port
42. Assembly language is 3. Both 1 & 2 are correct (*)
4. None of the above are correct
1. Low level language
2. High level language (*) 50. The screen in the laptop computer is
3. Machine language
4. All generation language 1. CPT
2. LCD
43. Which of the following language used 3. Semi conductor display
memories 4. All of the above are correct

1. Machine language 51. Which of the following is fixed disk

2. Assembly language drive
3. High level language
4. All generation language (*) 1. Hard disk drive (*)
2. Floppy disk drive
44. Vol storages are those from where data 3. Winchaster disk drive
are lost 4. CD-ROM drive

1. When the programme is over 52. Unix is a

2. With respect to time
3. When the power is shutoff 1. A software
4. All of the above except c 2. A programme

CORRECT ANSWER IS MARKED * AT END 116

 REVISED OBJECTIVE QUESTIONS & ANSWERS

3. Multiuser operating system (*) 4. None of the above are correct

4. All of the above are correct
61. Which of the following is a scientific
53. Assembler is language

1. A software 1. COBOL
2. A translator (*) 2. ADA (*)
3. A programme 3. FOPTRAN
4. All of the above are correct 4. BASIC

54. High level language are 62. Which of the following is not a
language
1. Machine dependent
2. Machine independent 1. FOXPRROT
3. Language in which programme is done 2. LISP
in 1 & 0 3. C
4. Both 2 & 3 are correct (*) 4. VISUAL C++

55. Interpreter in computer field is a 63. Pick the odd man out

1. Software (*) 1. DOS

2. Floppy 2. UNIX
3. Hardware 3. WIN – 95
4. The special electronic circuit which 4. DBASE
translate high level to low level
64. A package is a
56. Internet system is based on
1. Software
1. WAN system (*) 2. Set of instruction
2. LAN system 3. A programme
3. Mainframe computer system 4. All of the above are correct (*)
4. Many computers connected to a other
computer 65. Windows 3.1 is a/an

57. GUI stands for 1. Operating system (*)

2. Operating environment
1. Graphical user interface (*) 3. Package
2. Graphical user internet 4. Language
3. Graph & user interface
4. Graph & user internet 66. Which of the following is not a high
level language
58. Y2K problem is a
1. Basic
1. Software problem 2. C
2. Hardware problem 3. Assembly
3. Data problem (*) 4. Cobol
4. All of the above are correct 5. None of the above are correct

59. Virus affects 67. Which of the following is not a high

level computer language
1. Hardware
2. Software 1. Windows (*)
3. Both 1 & 2 are correct (*) 2. Visual C++
4. None of the above are correct 3. Coral
4. Pascal
60. Anti virus software is
68. DOS stands for
1. Dreaded software
2. Software to scan & remove virus (*) 1. Data operating system
3. Package 2. Disk operating system (*)

115 CORRECT ANSWER IS MARKED * AT END

REVISED OBJECTIVE QUESTIONS & ANSWERS

3. Diode operating system 2. Germenium

4. None of the above are correct 3. Alluminium (*)
4. Cu
October 1998
8. Selenium rectifiers when connected in
1. In d.c. generator single plain coil is series increases
rectangle, coil is perpendicular to
main flux, emf induced in coil. 1. Current handling ability of rectifiers
(Inparallel)
1. Maximum 2. Current and voltage handling ability of
2. Minimum rectifiers.
3. Zero (No Voltage) (*) 3. Voltage handling ability of rectifiers (*)
4. None of the above 4. None of the above

2. In carbon pole voltage regulator 9. Silicon rectifier (cathode) is made of

carbon pile is
1. Silicon
1. Granular Surface 2. Germinium
2. Resistance between two carbon faces 3. Copper (*)
depends on area of contact 4. Alluminium
3. Resistance between two carbon faces
depends on pressure of contact 10. "Firing" term used in
4. All above correct (*)
1. Diode
3. In Nickle Cadmium battery specific 2. LED
gravity of electrolyte is 3. SCR (*)
4. Transistor
1. Unchanged (*)
2. Gives number indication of the state of 11. In dot metric system use
the charge of the cell
3. All above are correct 1.
2. 7 × 4 Led = 28 Segment
4. In Lead – Acid cell grid plates alloy is 3.

1. Lead 12. Transformer rectifiers secondary

2. Lead Peroxide winding is connect in
3. Lead Antimony (*)
4. None of the above 1. Star
2. Delta
5. In a.c. circuit rms value divided 3. Star Delta (*)
average value 4. Delta Star

1. Creast Factor 13. In general services wiring which wire

2. Amplitude Factor is suitable
3. Form Factor (*)
4. All above are correct 1. PVC
2. Glass Braid
6. Resistor colour coding is yellow, 3. Nylon
violet, orange will silver band. 4. All above are correct (*)

1. 470 5% 14. In high operating temperature which

2. 47 5% wire is use
3. 47000 5%
4. 47000 10% (*) 1. PREN
2. EFGLASS (*)
7. Selenium rectifiers, base sheet 3. TERSIL
material is 4. FEPSIL

1. Selemium 15. In UNIFRE – 'F' conductor is

CORRECT ANSWER IS MARKED * AT END 116

 REVISED OBJECTIVE QUESTIONS & ANSWERS

4. All above are correct

1. Aluminum Plating
2. Copper Plating 23. In D.C. shunt motor running at rated
3. Nickel Plated Cu (*) speed field winding is open, the motor
4. Tinned Copper is

16. Electrical Bonding 1. Rotate at rated speed

2. Stopped immediately (*)
1. Limit potential difference between all 3. Slowly decrease speed
parts 4. None of the above are correct
2. Eliminate spark discharge and fire risk.
3. Prevent the possibility of electrical shock 24. Mark the correct statement
4. All above are correct (*)
1. Nibble is half byte (*)
17. ATA – 100 coding for cable 'Position 2' 2.
indicate 3.
4.
1. Functional Circuit (*)
2. Unit Number 25. In Lead – Acid Battery, spillage
3. The segment of cable electrolyte is neutralize by
4. None of the above are correct
1. Ammonia & Water
18. ATA – 100 coding for cable 'Position – 2. Vinegar
b' (N) indicate 3. Bi – Carbonate (Backing Soda) & Water
4. 1 & 3 are correct (*)
1. Neutral
2. Phase 26. Printed circuit board made by
3. Earth Connected Cable (*)
4. None of the above are correct 1. Lithographic
2. Photographic
19. In general electrical circuit 3.
4.
1. Switch in off
2. De-energise relay 27. Light emitting diode
3. Close C.B.
4. All above are correct (*) 1. Conduct forward bias
2. Conduct reversed bias
20. Co-axial cable 3. 4 × 7 dot matrix = 28 diodes
4. 1 & 3 are correct (*)
1. Shielded against electrostatic and
magnetic field 28. In Servo Mechanism System gain B
2. Do not radiate, they will not pick up and
energy 1. Open loop
3. An electrostatic field does not extend 2. Close loop (*)
beyond the outer conductor. 3. As in (1) Negative feedback
4. All above are correct (*) 4. As in (2) Positive feedback

21. Current Limiter 29. Boolean algebra Theorems

1. Low Melting Wire 1. A . A = 1

2. High Melting Wire (*)
3. Thermal Device 2. A + A =1
4. None of the above are correct 3. A + A = 1 (*)
22. In D.C. starter generator 4. A= A
1. Shunt 30. In 16 bite hexadecimal
2. Series
3. Fully compounded (*)

115 CORRECT ANSWER IS MARKED * AT END

REVISED OBJECTIVE QUESTIONS & ANSWERS

1. 2 × 16
2. 162 37. Capacitance of a capacitor is
16 measured by
3. 1616 (*)
4. 2 + 16 1. Maxwell bridge
2. Wheat stone bridge
31. Make the correct statement 3. Schering bridge (*)
4.
1. LSI more than 100 gate (*)
2. MSI 12 to 99 gate 38. Slip speed of motor having speed of
3. SSI gate using less than 10 1440 rpm 50 Hz.
4. None of the above
1. 100
32. Current flowing in a circuit having 2. 60 (*)
resistance of 8 Ω inductive reactance 3. 50
4. 120
of 12 Ω and capacitive reactance of 18
Ω, connected in series and across the
39. Synch speed of a motor having 4
supply of 20 v is
poles, 50 Hz.
1. 1.5 amp.
1. 1600 rpm
2. 2 amp. (*)
3. 1 amp. 2. 1500 rpm *
4. 4 amp. 3. 1200 rpm
4. 2000 rpm
33. A transformer having primary turns of
2000 connect across supply of 250 v, 40. Energy stored in a inductor having
give second output of 200 v. what is inductance of 10 m H and current of 4
the number of turns in second. amp.

1. 1500 1. 160 milli joules

2. 1000 (*) 2. 80 milli joules (*)
3. 2000 3. 160 joules
4. 1000 4. 1600 joules

34. While working of Lead acid battery, October 2003

electrolyte is touched to the eyes, whit
will do ? 1. A resistance of 6 Ω and inductance of 8
Ω connected in series across 200 v. 50
1. Rinse the eyes with plenty of water cps power supply. Voltage drop across
2. Eye rinse with solution of bicarbonate of 6 Ω res. Is
soda (*)
3. Rinse the eyes with water & KOH. 1. 200 v
4. None of the above. 2. 60 v
3. 120 v (*)
35. When megger is not in use, where its 4. 100 v
point is located. 5.
2. Two signals of same amplitude,
1. Extreme right hand side frequency and phase difference forms
2. Extreme left hand side (*) lissijons figure of
3. In centre
4. None of the above 1. Circle
2. Straight line with angle of 45°
36. CE Transistor having highest. 3. Straight line with angle of 130°
4. Ellipse
1. Power gain (*)
2. Current gain 3. Lap wdg is used for
3. Voltage gain
4. Input Impedance 1. High torque

CORRECT ANSWER IS MARKED * AT END 116

 REVISED OBJECTIVE QUESTIONS & ANSWERS

2. High voltage 3. If excited on load, field resistance should

3. Low voltage be equal to the minimum resistance.
4. Low current 4. All of the above

4. Transistor connecting in which 10. Conduction for half cycle is possible in

configuration having highest current
gain. 1. Class A amplifier
2. Class B (*)
1. Common base 3. Class C
2. Common collector 4. Class D
3. Common emitter (*)
4. None 11. Insulators have

5. In nodole analysis 1. Full valence bend

2. Empty conductor bend
1. Number of simultaneous equation to be 3. High energy gap
solution becomes (n – 1) 4. All of the above (*)
2. Network Sh__________ atleast
______________ 12. In a triode the usual working point on
3. 1 & 2 are correct (*) the slope called
4. None of the above
1. Tube factor
6. Peab value is 2. Tube coefficient
3. Amplification factor
Maximum Value 4. All of the above (*)
1. (*)
PMS Value 13. Scott connection is used for
PMS Value
2.
Maximum Value 1. To convert 3 φ to 2 φ
Average Value 2. To convert 2 φ to 3 φ
3. 3. 1 & 2
RMS Value
4. To convert 3 φ to 3 φ
RMS Value
4. 14. Starting of slip ring induction motor by
Average Value

7. Minimum distortion is achieved in

1. Start ∆
2. Tehostatic Control
1. Class A (*) 3. Resistance in rotor circuit (*)
2. Class B
3. Class A – B 15. Alternating values normally given in
4. Class C
1. r.m.s. (*)
8. Power gain in a PNP Transistor is 2. Av value
Maximum in 3. Max value

1. CC 16. Which winding is nearest to the core

2. CB
3. CE (*) 1. L.V. (*)
4. None of the above 2. H.V.

9. Voltage build up condition for shunt 17. Thickness of lamination reduced in xmer
generator low eddy current loss

1. Their must be sufficient diode at 1. Low eddy current loss (*)

magnetism in the poles (*) 2. Hyst loss
2. If excited on open circuit positive field 3. Both
resistance should be more then critical 4. None of the above
resistance.

115 CORRECT ANSWER IS MARKED * AT END

REVISED OBJECTIVE QUESTIONS & ANSWERS

18. Depletion layer contains 3. Low speed

4. 1 & 2 are correct (*)
1. Positive ions
2. Negative ions 27. Electrical characteristic of DC motor
3. 'C' & positive and negative ions (*)
4. Fixed positive ions 1. Ta / Ia (*)
2. Speed / T
19. In Lead – acid battery as temp
increases 28. Digital switching

1. At high temp, electrical capacity of 1. Flip – flop

battery increases 2. Bistable multivibrator
2. High temp diffusion increases. 3. Debouncing
3. At high temp performance improves 4. All of the above (*)
4. All of the above
29. Mark incorrect advantage of 3 φ supply
20. Unity power in
to 1 φ supply
1. Resistive circuit (*)
1. Saving in material
2. Series
2. Cost saving
3. Parallel
3. Efficiency better
4. All above correct
4. P - __
21. Increasing Q factor
30. In ∆ connection
1. As inductance increases (*)
2. Capacitance increases 1. Voltage 120° apart (*)
3. Resistance 2. Current ____ by 30°
4. Resistance & low ohmic drop 3. Current lead by 30°
22. Induction motor change in phase 4. 3 VLIC cos φ

1. Direction changes (*) 31. In an a/c if actuator is moving so

2. Runs in some direction _________ and the feedback pcth not
working then the system become
23. Ballistic galvonometer is used for
1. Open loop (*)
1. Flux measurement 2. Closed loop
2. As in 1 & _________ (*) 3. Cannot be counted as servo system
3. Control spring __________ because servomotor not there.
4. Mag inertia ________ 4. __________

24. When magnetic material is heated 32. In Feedback

1. Curie point (*) 1. Stability Increase (*)

2. Maxwell point 2. Stability Decreases

25. In starting of DC motor, no volt ____ is 33. Maxterm

used for
1. AND – OR invert logic (*)
1. To hold the arm 2. OR – AND logic
2. Release the arm 3. AND – OR logic
3. For overload protection 4. None of the above

26. Generator will fail to start in which 34. + Q charge on solid sphere is
circumstances
1. Equally disturbed throughout the surface
1. Open circuit in field (*)
2. Reverse polarity 2. Only on the surface
3. Concentrated at centre

CORRECT ANSWER IS MARKED * AT END 116

 REVISED OBJECTIVE QUESTIONS & ANSWERS

44. LCD
35. Electrostatic meters are used as
1. Dynamic scattering
1. Voltmeter (*) 2. Field effect
2. Ammeter 3. ASCII
3. Ammeter, voltmeter, wattmeter 4. Segmented type

36. Stalling current is 45. LED emmits light when

1. When armature (load) current is zero (*) 1. Reversed biased

2. Delation low increased
37. In transformer core on load 3. Electro and hole are merged. (*)

1. Approximate some flux as on no load. 46. CRT has electrode color given
(*)
1. 3 (*)
38. In transformer at no load, current 2. 4
consists of 3. 2
4. None of the above
1. Reactive and active components (i.e.
Iee & Iw) (*) 47. P Type semiconductor is doped

39. If by mistake during maintenance the 1. Germanium with Phosphorus

armature wdg of motor is reversed then 2. Germanium with Antimony
3. Germanium with Indium (*)
1. Motor will not rotate in opp direction then 4. As 1 & 2 are correct
it was previously rotating.
48. Semiconductor doped with arsenic
40. In case of syn motor when Eb = V motor
is said to be 1. P type
2. N Type (*)
1. 100 % excited
2. Overexcited with leading point 49. Instrument panel lighting is done by
3. Underexcited with leading point
4. Underexcited with lagging point 1. Intgranel light (*)
2. Pillar
41. In a 3 φ power system it wattmeters are 3. Bridge high
removed, you can use which of the 4. Trans illuminated
following for power ________
50. Cable insulator can with stand high
1. Three voltmeter method temp and hydraulic fluid
2. Three ammeter method
3. Ballistic galvanometer 1. Ny Vin
4. 1 & 2 are correct (*) 2. Pren
3. Tensil
42. Transistor common base configuration 4. EFGlam (*)
(Theraja)
51. Power supply system distribution
1. High voltage gain (*)
2. High power gain 1. Parallel bus
3. High current gain 2. Split parallel bus fair
4. High resistance
52. Kirchoff's Law applicable to
43. Semiconductor doping conductivity
1. DC only (*)
1. Increase (*) 2. AC only
2. Decrease 3. AC & DC
3. Decrease after certain temp.
53. IR voltage drop calculation consider

115 CORRECT ANSWER IS MARKED * AT END

REVISED OBJECTIVE QUESTIONS & ANSWERS

1. Battery communication 2. 45 (*)

2. Direction of current fluid. 3. 37

54. Photo sensitive diode 62. Resistance of Bonding between two

boted ________
1. When light falls emf generator (*)
2. When light falls chemical section take 1. 1Ω
place 2. 0.5 Ω
3. High emits by current flows
3. .025 Ω (*)
55. If number of uniform wire and core 4. 0.5 mega Ω
length is double inductance will be
63. Induced emf is depends on
1. Double
2. Half 1. Flux density
3. Quadruple (*) 2. Rate of change of flux linkage (*)
4. No Change 3. Flux line cut

56. Triode gride is 64. Capacitance dos not depend on

1. Negative potential 1. Plate area

2. Positive potential 2. Dielectric material
3. Negative and more positive than 3. Thickness of plate (*)
cathode (*)
4. Negative and more negative than Q
cathode. 65. If 1 w jubilant charge of 10 farad c =
V
57. Landing gear selecting lever weak s/w , capacitance voltage is
is located at
1. 10 v (*)
1. Landing gear selecting lever 2. 100 v
2. Brace Strut 3. 1000 v
3. Shock Strut (*)
66. Advantages of electrical / airdriven
58. Flaming left hand rule middle finger motor than hydraulic motor
indicates
1. Reliability
1. Direction of current (*) 2. Many power (*)
2. Torming direction 3. More power
3. Flux 4. Accurate power

67. For temp compensation which

59. Power of there phase circuit V3, VL, I2 capacitor used
cos θ, cos θ is angle between
1. Ceramic (*)
1. Phase voltage and phase current (*) 2. Electrolytic
2. Line voltage and line current 3. Paper
3. Phase voltage and line current 4. Mica
4. Line voltage and line current
68. BCD invalid
60. Mark the correct statement (906) pp
barnad grobe 1. 1010 (*)
2. 0100
1. Nibler is half byte (*) 3. 0101
2. 4 bits is one byte 4. 0111
3. Nibler is 16 bits
69. 10 Ω low resistor
61. Octal of Binary 10001012 is
1. Carbon
1. 54 2. Wire wound (*)

CORRECT ANSWER IS MARKED * AT END 116

 REVISED OBJECTIVE QUESTIONS & ANSWERS

3. Variable 78. Essential services connected directly

4. All above to

70. Equalizing bar are required in (Parallel 1. Aircraft generators

Operation) 2. Batteries
3. Static inverter
1. Series (Property) 4. 1 & 2 are correct (*)
2. Shunt
3. Alternator 79. For more precise and high temperature
4. Compound (*) greater stability with temperature
change use
71. Effect of screen grid
1. Carbon
1. RF amplifier (*) 2. Metal film
2. Capacitor between c 3. Wire wound
3. Amplification factor 4. Chip (*)
4. All of the above are correct
80. Thickness of lamination of transformer
72. Armature current depends on

1. 410 1. Eddy current loss

2. 440 2. Frequency (*)
3. 20 3. Cu loss
4. 2 amp (*) 4. Efficiency

73. State of charge of Ni – cad 81. Cu loss of transformer depends on

1. Ferominal voltage 1. Voltage

2. State of discharge 2. Current (*)
3. 1 & 2 are correct (*) 3. Voltage and current
4. Watts
74. Which memory is used on every read
cycle 82. In transformer when secondary is
loaded then
1. EPROM
2. PROM 1. It neutralized the primary flux
3. ROM 2. It does not affect primary flux
4. EAROM (*) 3. Same flux flows through the primary as
at no load (*)
75. Capacitor with polarity 4. 1 & 3 are correct

1. Electrolytic (*) 83. In converting two winding transformer

2. Ceramic to step up auto transformer
3. Paper
4. Mica 1. Flux flows through the secondary
increases
76. EMF induced in motor 2. Connect the transformer as additive
polarity (*)
1. Flat hand rule 3. Connect the transformer as subtractive
2. Fleming right hand rule (*) polarity
3. Lenz's law 4. Flux linked with the primary winding is
4. Right hand corek crew less

77. Capacity characked of lead acid 84. For matching low impedance to high
impedance circuit which configuration
1. One month is used.
2. 3 month (*)
3. Every shop visit 1. CB
2. CC (*)
3. CE

115 CORRECT ANSWER IS MARKED * AT END

REVISED OBJECTIVE QUESTIONS & ANSWERS

4. CB and CC
1. In DC circuit only
85. Mark the correct statement, for fully 2. In DC and AC circuit
valency band, empty conduction band 3. In DC and specified AC circuit (*)
and high energy gap. 4. In AC circuit only.

1. Conductor 92. Clutch is used in actuators for

2. Semiconductor
3. Insulator (*) 1. Mechanical overloading (*)
4. Absolute insulator 2. Motor cut off
3. Protection of o limit switch operation
86. In ATA 100 specification for cable over travel.
position '3' indicate 4. Prevent overheating of motor.

1. Function of circuit 93. Mark incorrect statement, for CE

2. Segment of cable transistors configuration,
3. Cable number 4 (*)
4. Unit number 1 1. High impedance
2. High power gain
87. Smoke detector is used in aircraft 3. Low voltage gain (*)
4. High current gain
1. Engine department
2. Landing gear section 94. Intensity control of CRT adjusted by
3. Lavatory section (*)
4. Cockpit 1. Secondary anode voltage varied.
2. Negative voltage of grid is varied (*)
88. Mark the correct statement, while 3. Voltage of focusing anode is varied
running induction motor, 4. Voltage of first anode is varied.

1. Rotor torque is depend on rotor 95. Soldering is avoided by quick joining of

resistance two contact is
2. Rotor torque directly proportional to
applied voltage 1. Crimping (*)
3. Rotor torque is inversely proportional as 2. Hard solder
standstill reactance 3. Silver solder
4. Rotor resistance is equal to rotor 4. Brazing
reactance (*)
96. Photo electric effect is
89. In landing gear retraction extension
system, horn sounds and red light 1. Photodiode
comes on when 2. Phototransistor
3. Light rays falls on photocell (*)
1. Any discrepancy is found in landing gear 4. LED
2. Any other gear not down and locked (*)
3. 1 & 2 correct 97. Which gate is used for parallel
switching operation
90. Aircraft Schematic diagram is drawn
on, when 1. OR (*)
2. AND
1. When aircraft is in the ground and CB is 3. NOR
closed 4. NAND
2. When aircraft is in the ground and
switches off (*) 98. Operation code stored during fetching
3. During flight position and supply is off. in
4. When aircraft is in the ground and
external supply is connected. 1. Instruction resistor
2. ALU
91. Mark the correct statement, Shunt is 3. Program center
used, 4. Accumulator

CORRECT ANSWER IS MARKED * AT END 116

 REVISED OBJECTIVE QUESTIONS & ANSWERS

99. In servo system the motor used 107.In microprocessor numerical alphabets

1. Single phase 1. BITE code

2. 2 phase (*)
3. 3 phase 108.Mark the correct statement, in
4. Multiphase blushless alternator,

100.Aircraft instrument motor used 1. Rotory rectifier supply DC to exciter

winding of main generator
1. DC shunt wound motor 2. Rotory rectifier supply DC to GCU
2. Compound wound motor 3. Rotory rectifier supply DC to exciter
3. Single phase induction motor (*) generator.
4. 1 & 2 are correct
109.Mark the correct statement, concept of
101.In carbon pile voltage regulator, lighting is such that,
voltage coil resistance is adjusted by,
1. Taxi light are at the tip of the wind
1. Air gap between magnetic core and 2. Landing lights are bright (*)
armature (*) 3. Beacon lights are at the tail tip
2. Resistance is minimum
3. Ballast resistance adjustment 110.Electrical system and circuit control by,
4. 1 & 2 are correct
1. Switch and relays (*)
102.Aircraft generator busbar is made up of 2. Microswitch and clutch
3. Switch and brake
1. Copper strip (*) 4. Brake and clutch
2. Aluminium bar
3. Copper rod 111.Conduct provided for cable for,
4. 1 & 2 are correct
1. Oil and fluid areas and mechanical
103.In transformer secondary is loaded support (*)
secondary flux, 2. Magnetic protection
3. High temperature areas
1. Neutralized the primary flux. (*) 4. To reduced the electrostatic induction
2. Does not affect the primary flux
3. Same flux as at no load 112.One wire broken detection system
4. 1 & 3 correct used,

104.Operation principle of proximity switch 1. Fenowal system (*)

is 2. Kiddi system
3. Lindburg
1. Cabin door
2. Passenger and freight door (*) 113.Generator output voltage ripple
3. Landing door removed by,
4. None of the above are correct
1. Filters only
105.Electrodynamometer instrument is 2. As in 1 and suitably rated capacitors (*)
used for 3. Shielding

1. AC measurement 114.For short term low resistance wire

2. DC measurement material used
3. AC and DC measurement (*)
4. All above are correct 1. Copper
2. Aluminium
106.A transistor is above to conduct when, 3. Stainless steel
4. Silver
1. Collector is heavily doped
2. Its base region is narrow (*) 115.Mark the correct statement, wave
3. Its base region is wide winding is used because

115 CORRECT ANSWER IS MARKED * AT END

REVISED OBJECTIVE QUESTIONS & ANSWERS

2. Circuited biushbar
1. Equalizing connection are not required 3. Ground the line
(*) 4. 1 & 2 are correct
2. Reduced the induced emf
3. Same emf is produced 123.Mark the correct statement, in
4. Less material used differential current protection

116.In CSD oil used for cooling has a 1. Two current transformer are used (*)
pressure of 2. Three current transformer are used
3. As in 1 and connected between negative
1. 120 – 160 psi (*) and earth
2. Below 300 psi 4. As in 2 and connected between two
3. Above 300 psi phases.
4. Below 500 psi
124.Mark the correct statement, in batteries
117.Flat compound generator has
1. Capacity increases as rate of discharge
1. Full load voltage equal to no load decreases (*)
voltage (*) 2. Capacity increases as rate of discharge
2. Full load voltage is more than no load increases
voltage 3. Capacity decreases as rate of discharge
3. Full load voltage is less than no load decreases
voltage
125.Cell balancing is carried out when
118.Bonding is used aircraft to provide
1. Capacity is less then 80% (*)
1. Low resistance path (*) 2. Battery voltage is less
2. High resistance path 3. Battery cells is leaking

119.Relighting of combustion system 126.In capacitance type fire warning

during flight is done with system

1. Starter and ignition is used 1. Capacitance increases as temperature

2. Only starter is used increases.
3. Low rating is used (*) 2. Capacitance increases as temperature
4. High rating is used decreases.
3. Resistance increases as temperature
120.Current coil is RCCB is used for the increases.
purpose of 4. Resistance increases as temperature
decreases.
1. It aids the flux to voltage coil when the
current flows in the forward direction (*) 127.Sabilizing winding used in alternator as
2. It opens the circuit when the reverse
current flows from the battery to the 1. Transformer type of coupling is
generator provided.
3. It prevent the battery from overheating 2. Gives signal to voltage regulator circuit
when there is voltage fluctuation in
121.Resistor is in series with mutual voltage regulator circuit.
reactor 3. As in 1 & 2 are correct (*)

1. Time constant is directly proportional to 128.In Transistorized voltage regulator, DC

mutual reactance supply to rotor is continued.
2. Flux saturated when mutual reactor is
maximum 1. When there is conduction of zenor diode
2. When less voltage is apply to zenor
122.Mark the correct statement, differential diode (*)
current protection is used to detect 3. When transistor TI start to conduct.

1. Short circuit feeder line (*)

CORRECT ANSWER IS MARKED * AT END 116

 REVISED OBJECTIVE QUESTIONS & ANSWERS

129.Mark the correct statement, Form 1. 15 kv at 15 minutes

factor is the ratio of 2. 1500 volts for 5 minutes
3. Immersed in water for 1500 volts at 15
1. Maximum value to rms value minutes
2. rms value to average value (*) 4. Immersed in water for 15000 volts at 5
3. Peak to peak value minutes
4. Maximum to average value
137.Mark the correct statement, resistor
130.Hysterisis motor is not used in aircraft connected in parallel
because
1. Voltage across individual resistance is
1. The magnetism induced in the rotor and more than source voltage.
lagging characteristis rotor material (*) 2. Product of voltage and current across
2. Low hysterisis losses of motor individual resistor is additive
3. Current are additive. (*)
131.While monitoring aircraft electrical
system the following system is used. 138.Inductance of inductor is depend on

1. EICAS 1. Current through the coil and number of

2. ECAM turns of coil (*)
3. As in 1 & EFIS 2. Distance between the turns
4. 1 & 2 are correct (*)
139.External pressure of aircraft is increase
132.Shunt limited motor, and decreasing internal pressure by
the
1. 70% of flux produced by shunt winding
and 30% by series winding 1. Outflow valve
2. It has minor shunt and large series 2. Negative pressure relief valve (*)
winding (*) 3. Pylon valve
3. It has minor series and large shunt 4. Bypass valve
winding
140.APU connection
133.Exceptional sensitivity relay,
1. Connector is plug into the right side of
1. Polarized armature relay (*) the fuselage.
2. Slug relay 2. Connector is plug into the aircraft when
3. Heavy duty armature relay the battery is removed.

134.For measurement of capacitor and 141.The selection of diagram related to

dielectric loss of capacitor aircraft system and selection of status
measured in from
1. Schering bridge (*)
2. Wheatstone bridge 1. Flight phase
3. Hay's Bridge 2. Manual mode
4. Maxwell wien bridge
142.Mark the correct the statement
135.Thermal runway in battery is prevented
by 1. Ramp tester is produced by
manufacturer of equipment
1. Integral fan is connected in battery 2. Ramp tester is produced by
compartment for cooling of the battery manufacturer of aircraft
2. Constant current charging method is 3. Ramp tester is produced by tester
used carried out on ground
3. Device in battery to warning of high
temperature (*) JUNE 2000
4. All above are correct
1. The fundamental frequency is
136.Dielectric testing of cable is carried out
at, 1. w (*)
2. w/r

115 CORRECT ANSWER IS MARKED * AT END

REVISED OBJECTIVE QUESTIONS & ANSWERS

9. Metal conducts are generally used for

2. Alkaline batteries the level of covering cables
electrolyte with respect to plates
should be 1. Sheilding against signal interference (*)
2. In a/c fluid areas
1. Above (*) 3. Both are correct
2. Same
3. Below 10. HRC fuse should for
4. Complete filled
1. High rupturing capacity fuse (*)
3. Lead acid cell when it is overcharged it 2. Emits enclosed inert gase
causes.
11. Carbon resistors are preferred than
1. Sulphation (*) wire wound resistor because they have
2. Dechlorination
3. Chlorination 1. High strength
4. None of the above 2. High stray inductance (*)

4. Alkaline batteries as compared to acid 12. Compensating winding used in

batteries generator

1. Cheaper (low initial cost) 1. Lie in series with armature winding

2. Lower weight to cap. Ratio 2. As in 1 and in series with the inter pole
3. Higher rate of charging and insensitive winding
4. Higher power to weight ratio (*) 3. Sides lie parallel to the sides of the
armature coil
5. The meter that is suitable for only DC 4. All above are correct (*)
measurement
13. Compensating winding used in
1. Moving coil type generators
2. Permanent magnet (DC) (*)
3. Electrodynamic type (AC and DC) 1. Reduce reactance sparking
4. Hot wire type (AC and DC) 2. Brush wear and commutator wear
reduction
6. For measurement for very high 3. Reduce ratio interference
voltages upto 500 kv instrument type 4. All of the above are correct (*)
used is
14. A 4 pole, 12 slots lap wound DC
1. Electrostatic voltmeter armature has two coils sides / slot.
2. Hot wire type (*) Assuming single turn coil and
progressing winding. The back pitch
7. Conductor and insulators used in cable would be
of type MIL – W – 5086 A (Type 2) as
1. 5
1. Tinned copper or aluminium positive 2. 7 (*)
nylon. 3. 3
2. Tinned copper or aluminium glass 4. 6
positive nylon (*)
3. Alluminium 15. Between no load and full load motor
develops the least torque.
8. In Aircraft wiring it is necessary the
wire should be have 1. Series (*)
2. Shunt
1. High current withstanding capacity 3. Commulative compound
2. Least of voltage drops betwen 2 ends 4. Differential compound
3. Should be flexible
4. All are correct (*) 16. Corel of a magnetic amplifier

CORRECT ANSWER IS MARKED * AT END 116

 REVISED OBJECTIVE QUESTIONS & ANSWERS

1. mmf increases gradually with flux 25. In a transistorized voltage regulator

density used in alternator the output voltage
2. mmf increases as flux density increases depends upon
3. Same as in X'former
1. Input voltage
17. The ordinary efficiency of a given 2. Resistor connected in series with
transformer is maximum when transistor (*)
3. By adjusting the screw of an armature
1. If runs at half full load contact.
2. If runs at full load
3. If it Cu loss equals to iron loss. 26. The output voltage of a step down type
switching voltage regulator depends on
18. Two x'mer operating in parallel having
equal outputs and voltage ratio carry 1. Input voltage
different loads because 2. Duty cycle
3. Transistor on time
1. They have an equal percentage 4. All of the above are correct (*)
impedance (*)
27. Common base configuration is used
19. Regarding skewing of rotor bars in a because it has high
SCIM
1. Current gain
1. It reduces magnetic ham during its 2. Voltage gain (*)
operation. 3. Power gain
2. It prevents coffing 4. Input impedance
3. Both 1 & 2 are correct (*)
28. A class B push pull amplifier has the
20. Rotor Rheostat control of starting main advantage of being free from
torque can be applied in
1. Any circuit imbalance
1. Slip ring motors 2. Unneauted noise
3. Even order harmonic distortion (*)
21. Hysterisis motor rotor material used is 4. DC magnetic saturation effects

1. Chrome steel (*) 29. The extremely high input impedance of

a mosfet is primarily due to
22. The power factor of a series RLC circuit
at is half power points is 1. Absence of its channel
2. Negative gate source voltage
1. Unity 3. Depletion of current carries.
2. Lagging 4. Extremely small leakage current of its
3. Leading gate capacitor. (*)
4. Either 2 & 3 (*)
30. In RC phase shift oscillator circuit
23. Current flow in a semi conductor
depends an the phenomenon of 1. There is need for feedback
2. Feedback factor is less than unity
1. Drift 3. Pure sine wave output is possible (*)
2. Diffusion 4. Transistor parameters determine
3. Recombination oscillation frequency.
4. All of the above are correct (*)
31. A half adder can be constructed
24. A LED emits visible light when its
1. Two XNOR gates only
1. PN junction is reversed biased 2. One XOR and one OR gate with their
2. Depletion region windows output connected in parallel
3. Holes and electrons recombine (*) 3. One XOR and one OR gate with their
4. PN junction becomes hot input connected din parallel.
4. One XOR and one AND gate (*)

115 CORRECT ANSWER IS MARKED * AT END

REVISED OBJECTIVE QUESTIONS & ANSWERS

32. An RTL logic family uses 4. Should be soldered for better connection
(*)
1. Resistor diode
2. Resistor and transistor (*) 40. The requirement of navigation light
3. Resistor diode and transistor
1. A red light at the left side from point
33. Which is the fastest logic line currently directly ahead through an are of 110°
available and green light at right side with a
similar are of visibility
1. TTL
2. High speed TTL
2. A green light at the left side and red light
of the right side from a point directly
3. ECL (*)
ahead through an arc of 110°.
34. CMOS logic family uses only 3. As in 1 and white light visible from the
rear of the a/c through an arc of 140°.
1. MOSFETS and resistors 4. As in 1 and white light visible from the
2. NMOS circuits rear of the a/c through an arc of 70°.
3. MOSFETS (*)
4. Bipolar transistor 41. Comp circuit with no power loss
35. The signal to be observed on the 1. Capacitor
screen of an oscilloscope is applied 2. Inductor
3. Capacitor and inductor
1. Across its X plates 4. All of the above (*)
2. Across its Y plates
3. To the horizontal amplifier 42. Real power developed in circuit
4. To the trigger circuits containing resistance and reactance
36. The deflection sensitivity of a CRT 1. I and R
depends inversely on the
2. VI Sin φ
1. Length of the vertical deflecting plates 3. V2 × reactance
2. Distance between screen and deflecting 4. VI Cos φ
plates
3. Deflecting voltage 43. Shunt motor with load constant speeds
4. Separation between Y Plates (*) depends upon

37. The direction of the rotating armature 1. Eb (*)

current in DC motor is decided by 2. Flux

1. Flemings left hand rule (*) 44. More propogation delay time
2. Faraday's law
3. Constant law 1. High speed TTL (6 numbers)
2. ECL (0.75 to 2 numbers)
38. Parallel LC resonant circuits provides 3. TTL (10 numbers)
4. CMOS (Very less)
1. Equal AC flow through L & C
2. High impedance at certain frequency 45. Alkaline batteries state of charge
3. Number AC power determined
4. All above are correct
1. Free gassing at the end of cycle
39. The bonding jumpers which statement 2. Special gravity indication
is wrong 3. Voltage measurement (*)
4. All above are correct
1. Resistance should not exceed 0.003 Ω
2. Should be short as possible 46. In RAM
3. To coat it with sealing coating to prevent
corrosion 1. MSI
2. LSI

CORRECT ANSWER IS MARKED * AT END 116

 REVISED OBJECTIVE QUESTIONS & ANSWERS

3. SSI (*) 55. Battery excess charges

4. All above are correct
1. 100 %
47. The passive display is 2. 120 %
3. 140 %
1. LED 4. 180 % (*)
2. LCD (*)
3. CRO 56. Tumber switch are
4. Gas discharge
1. Togg'e Switch (()
48. Transformer at full load. Iron losses = 2. Micro
800 w considering maximum efficiency 3. Rush
Ca losses at half load 4. Rocker button

1. 800 w (*) 57. Magneto System spark / rev

2. 400 w
3. 1600 w 1. 1 spark
4. 200 w 2. 2 spark
3. 4 spark
49. In LCD display at dynamic scaltering
type 58. Initially APU started by

1. Background of display is black 1. Aircraft battery (*)

2. Scatler light in all direction (*) 2. External power supply
3. All above are correct 3. APU battery

50. I, CRT, intensity is adjusted by 59. EICAS system is used display of fault

1. Cathode 1. 2 p display CRT used

2. 1st Anode 2. Upside and downside
3. 2nd Anode 3. Side by side left side message form right
4. Negative grid control side

51. False fire warning due to 60. Antiskid wheel locked signal is given
by
1. Moisture
2. Due to dent and neck (*) 1. Transducer
3. Short circuit of element 2. Skid control sensor
4. 1 & 2 are correct 3. Sensor
4. Sousing circuit
52. Insulation used on wife for 400°F 61. Equivalent resistance at A & B
1. PVC
2. Nylon
1. 3Ω
3. Silicon braided (*) 2. 4.5 Ω
3. 6 Ω (*)
53. The heater of windshield are placed 4. 9Ω

1. Embedded (*) 62. Storbe light mark most correct

2. Attached to window statement
3. Adjacent
1. If operate on the principle of capacitor
54. 'Drop Out' means discharge in xenon tabe.
2. It is substitute to anticollision light.
1. When contact open (*) 3. If operates at flash frequency 70 per /
2. When contact closed min.
3. When coil attracted armature 4. All above are correct
4. When core attracted armature
63. Ram is

115 CORRECT ANSWER IS MARKED * AT END

REVISED OBJECTIVE QUESTIONS & ANSWERS

1. Power factor 100% in circuit

1. Volatile
2. Non – Volatile 1. In phase (*)
3. Data is stored by manufactured in 2. Current leading
manufacturing process 3. Current legging
4. Data can be rewrite 4. None of the above

64. MSI has (Medium Scale Integration) 2. In half wave rectifier form factor is

1. 10 – 100 1. π 2 (*)
2. Less than 30
3. 100 – 1000 2. π 2
4. More than 10000
3. π 3
65. In electrical system position of valve 4. π 3
and speed is indicates by
3. Shunt motor back emf suddenly
1. Potentiometer and techogenerator disappear
2. Potentiometer and servometer
3. Resistance 1. Motor will stop (*)
2. Motor will burn
66. Square mill used to 3. Motor will run

1. Square wire 4. Fuses material

2. Circular wire
3. Rectangular 1. Tin
2. Alloy of tin and bismuth
67. Cable use of before and after fire 3. Lead
4. All of the above are correct (*)
1. Nyvin
2. EFFGLASS 5. SCR is used for
3. EEPSIL
4. None of the above 1. Switch
2. Rectifier
68. Pitot state tube 3. Variable power output
4. All above are correct
1. Airspeed indicator
2. Altimeter 6. Maximum heat dissipation in rectifier
3. Vertical speed indicator
4. OAT 1. Anode
2. Cathode
69. A generator having 40 kva and 0.8 PF 3. Cu which form the cathode
KW 4. Surve as a heat sink and dissipater (*)

1. 36 kw 7. Low propagation delay

2. 32 kw
3. 30 kw 1. PTL
4. 140 kw 2. ECL (*)
3. DTL
70. Junctions box is installed as open side 4. RTL
should be
8. Passive display
1. Downside
2. Upside 1. LED
3. Horizontal 2. LCD (*)
4. Vertical 3. CRT
4. Gas discharged
FEBRUARY 1999

CORRECT ANSWER IS MARKED * AT END 116

 REVISED OBJECTIVE QUESTIONS & ANSWERS

9. Speed control of DC motor which 17. Which one of the following relay have
method is used for good response maximum sensitivity

1. Flux control (*) 1. Heavy duty relay

2. Armature resistance control 2. Low duty relay
3. Tapped field 3. Polarized relay (*)
4. Ward Leonard 4. Sludged relay

10. Static discharge wicks 18. What is the use to neuloalised spillage
of electrolyte from lead acid battery
1. Located at training edge of ailrons,
elevators and redder 1. Vinegar
2. Reduce corona discharge effect on 2. Boric acid
interferance of radio signal (*) 3. Ammonia (*)
4. Bicarbonate of soda
11. In which material permeability is less
than one 19. When should be a nickle cadmium
battery gives deep cycle treatment
1. Die magnetic < 1 (*)
2. Fero magnetic >> 1 1. Every month
3. Para magnetic > 1 2. Every 3 month
4. Non magnetic = 1 3. Every 6 month
4. 100 hours (*)
12. In heartly oscillator, the phase shift
between 20. Capacity of battery increased by

1. 90° 1. Size of plate

2. 180° 2. Number of plate
3. Electrolyte
3. 270° 4. Both 1 and 2
4. 360°
21. The function of the circuit indicate in
13. The propagation delay time is ATA 100 code
maximum
1. 1
1. TTL 3 numbers 2. 2 (*)
2. ECL 0.3 numbers 3. 3
3. CMOS 7 numbers (*) 4. 4
4. High speed TTL 1.5 numbers
OCTOBER 2003
14. Transformer lamination have
1. In Lissajous patterns when signal
1. Low resistivity and high hysteresis applied across x – y plates of same
2. High resistivity and high hysteresis frequency, amplitude and phase
3. High resistivity and low hysterisis (*) difference produced

15. In hysterisis motor rotor becomes a 1. Straight line having 45 degree angle to
permanent magnet horizontal (*)
2. Straight line with 135 degree angle to
1. Rotor speed lower than synch speed horizontal
2. Rotor speed higher than synch speed 3. Circle with
3. Rotor speed rotate at synch speed (*)
2. While handling NI-CAD battery, if the
16. The ratio of true power to the apparent eyes contaminated with the KOH wash
power of an AC circuit is known as the eyes with

1. Power factor (*) 1. Carbolic acid

2. KW / KVA 2. Plenty of water (*)
3. KVA / KW 3. Weak boric acid

115 CORRECT ANSWER IS MARKED * AT END

REVISED OBJECTIVE QUESTIONS & ANSWERS

3. Internal resistance of battery depends 2. EACAM

upon 3. FDAU
4. EFIS (*)
1. Plate area
2. Distance between the electrodes (*) 11. In modern aircraft, all bytes measured
3. Electrolyte solution on
4. All the above are correct
1. BITE Box (*)
4. Carbon resistors preferred than wire 2. BLACK Box
wound resistor because 3. TOOL Box
4. None
1. High stability
2. Low stray inductance 12. In 3 pin external DC power supply
3. Least the cost connector
4. Low power (*)
1. One of the positive pin is shorter (*)
5. Protection of batteries provided for
13. In large aircraft, external power supply
1. Internal heating connector
2. Excessive environmental temperature
3. Overheating of battery leads 1. 4th pin of large dia.
2. 2 pins of short diameter
6. Resistance of 6 ohm and inductive 3. As in 2 and supplying interlocking relays
reactance of 8 ohm connected in 4. As in 3 and connect the external AC
series to supply of 200 v. calculate power to the aircraft (*)
voltage drop across 6 ohm resistance.
14. Number of splice use between two
1. 120 v (*) connector
2. 150 v
3. 200 v 1. 1 (*)
4. 100 v 2. 2
3. 3
7. 3 Phase induction motor having rpm 4. 4
1440 and rotor speed of 50 Hz.
Calculate the slip 15. When syn motor runs on lagging p.f.,
if the load is reduced p.f. becomes
1. 50
2. 60 (*) 1. More lagging
3. 100 2. Less lagging
4. 40 3. Unity p.f.
4. Near to the unity p.f.
8. In Rotary inverter motor and generator
16. Highest power gain in
1. Having common arm. and field winding
2. Having same arm. and different field 1. CE (*)
winding 2. CB
3. Mounted on same shaft. (*) 3. CC
4. None
9. Proximity Switch use for the purpose
of 17. Highest current gain in

1. Landing gear operation 1. CE

2. Thrust reverser 2. CC (*)
3. Cabin door 3. CB
4. All the above are correct (*) 4. All

10. All flight data reads on 18. CMOS uses because,

1. EACAS 1. Requires less power (*)

CORRECT ANSWER IS MARKED * AT END 116

 REVISED OBJECTIVE QUESTIONS & ANSWERS

2. Low memory device 2. Feedback supply to hold in circuit of the

3. High speed ground power unit
4. 1 & 2 are correct
27. Mark the correct statement
19. In parallel operation of DC generator
improper division of load because of 1. Essential services directly connected to
battery bus bar
1. Voltage regulator adjustment is not 2. Generator bus bar are normally isolated
properly balanced
2. Ground the field 28. Clorona effect is reduced by
3. Field open
1. Static discharger (*)
20. When, Alternator fails 2. Coaxial cable

1. Ammeter shows reverse current, busbar 29. Brush wearing at high attitude due to
voltage equal to battery voltage
2. Alternator get disconnected by 1. Friction between commutator and brush
automatically 2. Static electrical charge due to friction
3. Contact resistance is negligible
21. Cross – short is check by 4. All of the above are correct (*)

1. Voltmeter 30. In modern turbojet aircraft

2. Ammeter
3. Ohmmeter (*) 1. Two batteries of are connected in series
4. 1 & 2 is correct and in parallel during starting of engine
2. Only one battery switch is on and then
22. When, input to megger is off, pointer connected in parallel
goes to 3. 48 volts is supply at the starting of the
engine by connecting the batteries in
1. Extreme LII (*) series and then 24 volts is applied by
2. Extreme RII connecting batteries in parallel (*)
3. Centre position
4. Any where position 31. When operating temperature is low,
lead – acid battery capacity,
23. Cutout of AVO operated by
1. Capacity decrease (*)
1. Electrically 2. Reduce electrolyte
2. Mechanically 3. Discharge
3. Electromagnetically (*)
4. Pneumatically 32. Advantage of constant voltage
charging on aircraft
24. Negative relief valve operated by
1. Protection against excessive gassing
1. Pneumatically 2. Reduced time (*)
2. Electrically 3. Reduced capacity
3. Hydraulically
4. Magnetically 33. Mark the correct statement, antiskid
autobrake system
25. The purpose of the 'Dump valve' in a
pressurized aircraft is to relieve 1. Automatic
2. Touchdown
1. All the positive pressure from the cabin 3. Deaccleration rate is less than manual
2. A negative pressure differential 4. All above are correct (*)
3. Pressure in excess of the maximum
differential 34. Window heat sensor

26. External power 'TRU' supply 1. Embedded in glass (*)

connected to 2. Touching with glass

1. DC relays and DC consumers 35. Mark the correct statement

115 CORRECT ANSWER IS MARKED * AT END

REVISED OBJECTIVE QUESTIONS & ANSWERS

3. Secondary anode at negative potential

1. Class 'D' connector is of fire proof type
2. Class 'A' is 44. Voltage amplification of amplifier

36. In part number of connector AN18A-10 1. Large load

'A' indicates, 2. Small

1. Class of connector 45. Maximum voltage drop across the

2. Type of connector cable connected between generator
3. General utility usage (*) and battery to any component should
not exceed.
37. In electrical system which diagram
shows one or more than one 1. 2 % of regulated voltage of the
generator or battery when the battery
1. Wiring diagram discharge at 5 minute rate
2. Schematic diagram (*) 2. 2 % of regulated voltage of the
3. Routine chart generator or battery when the battery
discharge at 1 hour rate. (*)
38. Smoke detector used in cargo 3. 10 % of regulated voltage of generator

1. Photo electric cell (*) 46. Lap winding is used for

2. Sniffer
1. High voltage machine
39. 'Slug' relay operated on the principle 2. Low voltage machine (*)
of 3. Loc current machine
4. High current and low voltage
1. Lenz's law (*)
2. Fleming's left hand rule 47. If the capacitor charge and then
3. Faraday's law halved it which factor will affects,

40. Network containing no source of emf 1. Chmige

is 2. Potential difference (*)
3. Dielectric material
1. Active 4. Capacitance
2. Passive (*)
3. Bilateral 48. Mark the correct statement
4. Unilateral
1. Compensating winding is connected in
41. Capacitance can be measure with the series with interpole
help of, 2. Compensating winding is connected in
with armature and parallel with interpole
1. Schering bridge (*) 3. Compensating winding is connected in
2. Hay's bridge series with armature winding and
3. Maxwell's bridge interpole (*)

42. Transformer of having 2000 turns on 49. Calculate the energy store in inductor,
primary supply with 250 volts, induced having inductance of 10 mH and
voltage in secondary of 200 volts. current of lamp
Calculate the secondary turns
1. 160 mj
1. 1600 (*) 2. 80 mj (*)
2. 1900 3. 160 joules
3. 2000 4. 1600 joules
4. 1500
50. Insulation resistance used above 400
43. Intensity control of CRO is done by degree centigrade.

1. Negative potential of grid (*) 1. Braided wire

2. Cathode of CRO 2. PVC

CORRECT ANSWER IS MARKED * AT END 116

 REVISED OBJECTIVE QUESTIONS & ANSWERS

3. Fibre glass (*) 58. Instrument used for measuring

4. Silicon rubber bonding in a/c

51. Asymmetrical waveform rms value 1. Bonding tester

calculated over 2. Ohm meter with wire and battery
3. Ammeter and battery
1. Full cycle 4. 1 & 2 are correct (*)
2. Half cycle (*)
3. Two cycle 59. Why the rotor bars of induction motor
4. Three cycle is placed deeper into the rotor

52. Time current characteristics of 1. To reduce iron loss

protection devices 2. To improve p.f.
3. To improve η
1. Above the wire capacity
2. Below the wire capacity (*) 60. Material of pole shoes are of
3. As close as possible to the wire capacity
1. Laminated sheet
53. To test generator or motor windings 2. Laminated sheet (*)
for opens 3. Cast iron
4. Thin soft iron lamination
1. Place armature in growler and connect a
110 v test on adjacent segment light 61. If load kept constant and p.f.
should light. (*)
increased then η will
2. Check adjacent segment on commutator
with an ohmmeter on high resistnce
1. Increase
scale
2. Decrease
3. Used a 12/24 v test light between the
3. Remains constant
armature core segments and shafts
62. In generator field winding consists
54. In fire detection system, false fire
warning due to,
1. Thick wire carrying for low current
2. Thin winding and high current
1. Improper routing or clamping the system
3. Thin winding and low current (*)
2. Moisture
3. Dents or kinks or crushed sensor
63. Fleming left hand rule middle finger
sections (*)
indicates
4. 2 & 3 are correct
1. Direction of current
55. In inductor 'A' of air core and 'B' iron
2. Direction of rotor
core then inductance in 'B' is
3. Direction of flux (*)
1. More (*)
64. For measuring insulation resistance
2. Same
megger consist of
3. Less
4. Not affected
1. Moving coil galvanometer
2. Voltmeter and ammeter coil (*)
56. Capacity of choke input filter is for
3. Ohm meter and ammeter
4. Ohm meter
1. Current smothering action
2. Voltage smothering action
65. Fuses and C.B. are used
3. As in 1 & 2 are correct
1. Hear loads
57. Ohm is used for measurement of
2. Hear bush bar
3. Between bush bar and load
1. Resistance
2. Inductive reactance
66. Relay contact get heated, due to
3. Capacitive reactance
4. All above are correct (*)
1. Low contact pressure (*)

115 CORRECT ANSWER IS MARKED * AT END

REVISED OBJECTIVE QUESTIONS & ANSWERS

2. Low voltage 3. Reducing flame.

3. Low current 4. None of the above.
67. Which instrument is used to measure R006. In triode grid
high frequency low current
measurement 1. Reducing space charge.
2. Prevents secondary emission.
1. Electromagnetic ammeter 3. It increases emission of electrons
2. Moving coil galvanometer (*)
from cathode to plate. *
3. Thermostat type instrument
4. Induction type instrument 4. Control electron flow from plate to
cathode.
68. Moving coil instrument is used to
measure R007. To check interior surface
condition of cylinder & surface
1. Low frequency AC signal
1. To be used Borescope.
2. High frequency AC signal
3. Both AC and DC signal (*) 2. To be used Fiberscope.
3. To be used Endoscope.
R001. Rockwell tester measures 4. All of the above are correct. *
R008. Radiography depends on
1. Resistance to penetration and depth. *
2. Diameter of impression. 1. Size and shape of the job.
3. Size of indentation. 2. Thickness of Materials.
4. All of the above are correct. 3. X-ray.
4. All of the above are correct. *
R002. P-N Junctions used as
R009. The diametric pitch indicates
1. Rectifier or Non return valve. *
1. Number of teeth per inches on pitch
2. Oscillator.
diameter.
3. Amplifier.
2. Size of the gear teeth.
4. None of the above.
3. As in (1) & (2) are correct. *
R003. In PNP transistor 4. None of the above is correct.
R010. Hand reamer is used to
1. Flow of electrons from emitter to
base. 1. Remove small amount of materials
2. Holes moves from collector to and expand a hole.
emitter. 2. As in (1) and is turned with tap
3. Flow of electrons from base to wrench. *
emitter. 3. Make an undersize or oversize hole
4. Flow of electrons from emitter to to correct size.
base. * 4, All of the above are correct.
R004. Cleaning of titanium spares by R011. At absolute zero temperature, an
1. Steel or steel wool. intrinsic semiconductor will act as
2. Iron scrapers. 1, Insulator. *
3. Mild abrasive or hands polish with 2. Super conductor.
aluminum. * 3. Neutral.
4. None of the above. 4. None of the above.
R005. Aluminum alloy are welded with R012. In semiconductor depletion zone
1. Oxidizing flame. 1. Has positive holes pairs.
2. Neutral flame. * 2. Has negative electrons pairs.

CORRECT ANSWER IS MARKED * AT END 116

 REVISED OBJECTIVE QUESTIONS & ANSWERS

3. Has neutral electron-hole pairs. * 3. Gray and white are used as decimal
4. None of the above is correct. multipliers for very small values.
4. All of the above are correct. *
R013. Internal barrier potentials in
semiconductor R019. When temperature is lowered
from room temperature to 50 0 K,
1. Increases with higher temperature.
resistance of Ge & Si
2. Decreases with higher temperature.* semiconductor will
3. No change with temperature rise.
1. Both increase. *
R014. Mark the correct statement 2. Both decrease.
1. Silicon semiconductor has zero 3. Ge decreases, Si increases.
reverse current with reverse voltage. 4. Si decreases, Ge increases.
2. Germanium semiconductor has zero R020. To check external threads
reverse current with reverse voltage
1. Thread gauge is used.
3. Varactor diode is used for electronic
tuning. 2. Ring gauge is used. *
4. As in (1) and (3) are correct. * 3. Plug gauge is used.
R015. Mark the correct statement 4. None of the above is correct.
R021. A modern computers executes
1. Tunnel diodes are also called ‘Esaki
diodes’. 1. One instruction at a time.
2. Tunnel diodes have heavy doping. 2. Millions of instructions at a time.
3. In tunnel diodes, current decreases 3. Millions of instructions in a second
with increase voltage and used as not at a time. *
an amplifier or oscillator. 4. None of the above is correct.
4. All of the above are correct. *
R022. In metal spraying process
R016. In Light Emitting Diodes (LED)
1. Metal is sprayed on copper / Nickel.
1. Gallium (Ga) is used for best
2. Metal is sprayed on solid surface.
efficiency.
3. Al / Cu / Ni are sprayed on the metal
2. Have several colors depending on
to improve corrosion resistance. *
the materials are used in the chip.
4. None of the above is correct.
3. Have high current consumption than
LCD.
R023. To improve corrosion resistance,
4. All of the above are correct. * pure aluminum is coated on both
R017. Liquid crystal displays (LCD) are side of alloy is known as

1. Dynamic scattering. 1. Al-clad.

2. Field effect type. 2. Pure clad
3. Dynamic scattering type produces 3. Both (1) and (2) are correct. *
frosty white letters on dark 4. None of the above is correct.
background and field effect type
produces black letters on silvery R024. The file used to make keyways
background. and slots is
4. All of the above are correct. *
1. Half round file.
R018. Capacitor color coding uses 2. Triangular file.
1. In mica capacitor six-dot systems. 3. Square file. *
2. In Tubular ceramic capacitor color 4. Knife file.
dots or bands.

115 CORRECT ANSWER IS MARKED * AT END

REVISED OBJECTIVE QUESTIONS & ANSWERS

R025. If drill size is not mentioned on 4. None of the above is correct.

the drill, then it is measured by
R031. In an air lock fastener the material
1. A drill gauge with fractions towards it can withstand is
the left & decimal towards the right
2. A drill gauge with fractions towards 1. Inscribe on the head of the stud in
the right & decimal towards the left. * 1000 of an inch. *
3. A hole gauge or SWG. 2. Stamped on the stud receptacle.
4. None of the above is correct. 3. No marking available.
4. None of the above is correct.
R026. In Rockwell hardness tester
R032. A formed rivet is removed by
1. A diamond cone & spherical ball is
used on material softer than C-20. 1. Center punch with drilling a hole
2. For softer materials. slightly smaller than shank diameter.
3. If the hardness scale overlaps top of 2. Center punch with drilling a hole
‘B’ scale & bottom of ‘C’ scale, ‘C’ slightly greater than shank diameter.
scale set up is used. * 3. Using flat chisel, chop off the head
4. None of the above is correct. 4. As in (1) and (2) are correct. *

R027. CPU of computers consist of R033. The most commonly used

insulating material for an aircraft
1. Input and output. is
2. Memory.
3. ALU and Control unit. 1. Nylon & cotton base.
4. Both (2) and (3) are correct. * 2. Rubber & silk base.
3. Teflon. *
R028. In work shop, parallel bars are 4. As in (1) and (2) are correct.
used to
1. Lift the Jobs. R034. In aircraft bonding & screening is
2. To mark the job parallel line. done to
3. To level the work piece. 1. Prevent static charge accumulation.
4. Both (1) and (3) are correct. * 2. Prevent radio frequency
R029. In a rheostat interference.
3. Eliminate ground wiring.
1. Both end terminals are used to vary 4. All of the above are correct. *
the resistance.
2. The middle and end terminals are R035. Ice box rivets, if not riveted in the
used to vary the resistance with prescribe time, can be
jockey in contact. *
3. All three terminals used to vary the 1. Rejected.
resistance. 2. Re-heat treated once.
4. Only one terminal is used to vary the 3. Re-heat treated for maximum of 3
resistance. times.
4. Re-heat treated any number of
R030. Tapered roller bearing times. *
1. Take axial & radial loads
R036. When a weld structure is cooled
simultaneously in one direction. *
2. Take heavy axial & moderate radial 1. The strength can be improved by
loads in either direction. hammering. *
3. Take axial load only.

CORRECT ANSWER IS MARKED * AT END 116

 REVISED OBJECTIVE QUESTIONS & ANSWERS

2. Hammering will destroying the joint. 4. None of the above is correct. *

3. As in (1) when prescribe in drawing.
4 None of the above is correct. R042. The strength of 18-8 steel can be
increased by
R037. In lead acid cell
1. Heat treatment only.
1. The positive plates are made of lead 2. Hot working only.
di-oxide(PbO2) and negative plate is 3. Cold working only. *
pure spongy lead. * 4. None of the above is correct.
2. The positive plates are made of lead
per-oxide (PbO) and negative plate R43. The filler material in composite
is pure spongy lead. material improves
3. The electrolyte H2SO4 does not take 1. The pot life, strength and make resin
chemical reaction while charging & application easier. *
discharging.
2. Shelf life and strength.
4. As in (2) and (3) are correct.
3. Curing is faster.
4. All of the above are correct.

R038. An alternating voltage supplied to R044. After swaging procedure, it is

the face of the crystal is found that the thickness of the
converted to sound wave sleeve is reduced

1. It shows correct swaging is done.

1. Known as Piezo-electric effect.
2. It is over swaged and job must be
2. Electromagnetic effect. discarded. *
3. As in (1) and frequency depends on 3. Open out and re-swaging to be done
the thickness of the crystal. *
4. None of the above is correct.
4. As in (1) and frequency depends on
the applied voltage. R045. Hawks bill snips are used to
R039. Mark the correct statement for 1. Cut internal curves and radii. *
radiography of X-ray
2. Cut external curves and radii.
3. As in (1) and (2) are correct.
1. They don’t travel in straight line.
4. None of the above is correct.
2. They don’t destroy living cells.
3. They heat the metal on which they R046. OR gate gives an out put when
fall.
4. They can’t be reflected & refracted. * 1. Any one of the input is energized.*
2. None of the input is energized.
R040. Bevel gear are used for 3. All of the inputs are energized.

1. Transmitting motion between shafts R047. Shank of the Hand reamer is

inclined at the angle each other. *
2. Taking heavy load with low speed. 1. Square in shape. *
3. Speed reducer. 2. Hexagonal in shape.
4. All of the above are correct. 3. Straight and taper.
4. None of the above is correct.
R041. In an ideal transformer
R048. XOR gate denoted in Boolean
1. Energy loss is caused by core. equation is
2. Copper loss is caused by conduction ______
3. Eddy current loss by magnetization. 1. A + B

115 CORRECT ANSWER IS MARKED * AT END

REVISED OBJECTIVE QUESTIONS & ANSWERS

2. A. B R056. Rocker arm and pin diameter is

3. A B.* measured by
4. None of the above is correct.
1. Telescopic gauge.
R049. Which of the following Boolean 2. Micrometer. *
algebra equation is not the
3. Hole gauge.
correct?
1. A + B = B + A R057. Current flowing through two
parallel conductors
2. A. 0 = 0.
3. A + 0 = A.
1. Current in same direction repels
4. A. 1 = 0. *
each other.
R50. AN steel fitting color is 2. Current in same direction attract
each other. *
1. Black. * 3. Current in opposite direction will
2. Blue. attract each other.
3. Green. 4. Current in opposite direction will
4. None of the above is correct. repel each other.
R051. H2So4 is neutralized by R058. A chisel is used to
1. Sodium bicarbonates. 1. Cut hardened steel.
2. Ammonia. 2. Cut any materials softer than it. *
3. Potassium hydroxides. 3. As in (1) and (2) are correct.
4. As in (1) and (2) are correct. *
R059. While replacing a tyre where one
R052. Close tolerance bolt is identified wheel has to be raised
1. By triangle with centre cross. *
1. A single jack is used.
2. By Circle with centre cross.
2. Other wheel must be chocked fore
3. By cross.
and aft.
4. None of the above is correct.
3. The wheel should be only high
R053. I beam is manufactured by enough to clear the ground.
4. All of the above are correct. *
1. Extrusion.
2. Drawing. R060. The Diode and Triode
3. Cold working. 1. Act as an amplifier & rectifier
4. None of the above is correct. * respectively.
R054. 7075 major alloy element is 2. Converts AC to DC and increase
magnitude of alternating current
1. Copper respectively. *
2. Magnesium. 3. Both (1) and (2) are correct.
3. Zinc. * 4. None of the above is correct.
4. None of the above is correct.
R061. Mark the correct statement for
R055. If weld is made quickly (wet flux) pure semiconductor
1. Cracking will occur.
2. Porosity will occur. * 1. They are poor conductor of
electricity.
3. Pitting will occur.
2. Ohms law does not hold true for
4. All of the above is correct.
them.

CORRECT ANSWER IS MARKED * AT END 116

 REVISED OBJECTIVE QUESTIONS & ANSWERS

3. They do not have large number of R067. Under the action of electric forces
free electron. in an electric field, mark the
4. All of the above are correct. * correct statement.

R062. Conductivity is increased of pure 1. Positive charge flow from lower to

semiconductor by higher potential.
2. Negative charge flow from higher to
1. Doping is done. lower potential. *
2. No impurities are added. 3. Charge flow lower to higher potential
3. Impurities deliberately added. 4. Positive charge can flow from any
4. Both (1) and (3) are correct. * potential to provide electric field
equal.
R063. The electric lines of force

1. Can never intersect each other. * R068. Mark the correct statement.
2. Always try to expand along their
1. Turnbuckle ends are normally made
length.
from cadmium plated steel.
3. Attract each other laterally.
2. Turnbuckles barrels are normally
4. Can exit inside a conductor. made of steel.
3. Turnbuckle ends may be of cable
R064. In case of current induced by eye, pin eye and fork eye. *
magnet, the strength of induced 4. As in (1) and (3) are correct.
current increases
R069. If sealer from heat treated steel
1. With decrease in area & number of parts on dirt accumulation on it,
turn of the coil. this may be cleaned by
2. With increase in relative motion of
the coil. 1. Sand blasting.
3. With decrease in area and increase 2. Wet blasting using liquid abrasive.
in number turn of the coil. 3. Wire brash and scraper.
4. As in (2) and (3) are correct. * 4. All of the above are correct. *

R065. Clevis bolt is used for R070. On a machine drawing, the

characteristic of a surface is
1. Shear loads only and require a specified by
shear nut. *
1. Proper dimension. *
2. Tensile loads and require a self
2. Limits and tolerance.
locking nut.
3. Fringe pattern.
3. Any type of load and require any
type of nut. 4. None of the above is correct.
R071. Common drilling machine perform
R066. The heat treatment method of
tempering depend on 1. Hole drilling.
2. Reaming and spot facing.
1. Type of steel. 3. Counter sinking.
2. Size and shape of the metals. 4. All of the above and also tapping &
3. The purpose to be used. lapping. *
4. All of the above are correct. *
R072. Cutting speed of drilling means

1. Speed of circumference.

115 CORRECT ANSWER IS MARKED * AT END

REVISED OBJECTIVE QUESTIONS & ANSWERS

2. The distance that drill would roll if

placed on its side.
3. RPM of the drill bit.
4. Both (1) and (2) are correct. *
R073. The thickness of gear teeth is
measured

1. At a point where the pitch circle of

the gear cross the tooth. *
2. By vernier caliper.
3. By Micrometer.
4. Both (2) and (3) are correct.

R074. The mutual inductance between

two coils is

1. Flow linked with one when current in

the other is unity.
2. EMF induced is one when the
current in the other is unity.
3. EMF induced in the coil when the
current through the coil itself
changes.
4. As in (1) and (2) are correct. *

CORRECT ANSWER IS MARKED * AT END 116