TDP 2 - Soils Eng. Soil Properties 1

2.
Soil Properties
TDP 2 - Soils Eng.
Soil Properties
Definitions
Origin of Soil:
Soil formed in-place is called Residual. Transported soils are described by the method of transportation:
Colluvium is soil that has been transported by gravity (i.e. particles roll down a steep slope, landslides). Alluvium is soil that has been transported to its present location by water. Aeolian or Eolian is soil that has been transported to its present location by wind.
TDP 2 - Soils Eng.
Soil Properties
Definitions
Origin of Soil:
Glacial till is soil that has been gouged out of the Earths crust by ice (glaciers) at one location and dropped at another.
There is usually little or no separation of particles by weight.
TDP 2 - Soils Eng.
Soil Properties
Soil Composition
Soil consists of solids and voids Solids are mineral particles Voids are air and water between the soil particles.
TDP 2 - Soils Eng. Soil Properties
Sample 1
4
Soil Composition
Volume total = V solid + V air + V water Weight total = W solid + W air + W water
TDP 2 - Soils Eng.
Soil Properties
Soil Water
Water content (w) is the percentage of the weight of water to the weight of the dry solids.

TDP 2 - Soils Eng.
Also can be called moisture content A saturated soil has its voids completely filled with water. Its water content is denoted by wsat. Soil below the water table is usually considered to be saturated. Dry soil contains only air in the voids. Wet soils have both water and air
Soil Properties 6
Soil Water
Certain weight relationships have been found to be useful:
Water content is the ratio of the weight of the water to the weight of the solids. This ratio multiplied by 100 is the percentage of water content or moisture content (w).
Ww w 100 Ws
w = moisture content (%) Ww= weight of water Ws = weight of solids
TDP 2 - Soils Eng. Soil Properties 7
Soil Water
Most soils contain water. Some definitions pertaining to water in soil are as follows:
Dry weight or Dry mass is the constant weight of a soil after being dried in an oven at a temperature of 110 5 C.
Optimum water or Optimum moisture content is the percentage of water in a soil, based on its dry weight, at which the maximum unit weight or density is obtained under a given compactive effort and is denoted by wo.
Dry soils require the addition of considerable water to reach wo. Soils with water content between dry and saturated are termed wet.
TDP 2 - Soils Eng.
Soil Properties
Volume-Weight Relationships
Unit weight () or density is defined as the weight per unit volume of a soil. The total unit weight includes the weight of soil solids and water divided by the total volume.
= unit weight
W Ww W s V V
Ws= weight of solids Ww = weight of water V = total volume W = total weight
TDP 2 - Soils Eng.
Soil Properties
Specific gravity (Gs) is the ratio of the weight of a given volume of the soil solids to the weight of an equal volume of pure water. The volume of solids used for determining the specific gravity of solids does not include any voids. Typically, Gs is reported for sands and fines. Values usually range between 2.5 and 2.8, with most falling near 2.65.
High organic content will lead to a lower value, heavy minerals will give larger values.
Soil Properties 10
TDP 2 - Soils Eng.
Units of weight and volume must be consistent.
W in lbs. V in ft.3
In soil engineering, density () and unit weight () are sometimes used interchangeably.
TDP 2 - Soils Eng.
Soil Properties
11
The unit weight of soil has specific denotations for each of the four most frequently used water contents:
Dry unit weight,
Ws , whereVw 0 V
Wet unit weight,

Saturated unit weight,
Ws Ww Wa m , where Wa 0 V
sat
Ws Ww , whereVa 0 V
Submerged unit weight, sub sat w Submerged unit weight is also known as buoyant unit weight (b).
TDP 2 - Soils Eng.
Soil Properties
12
Summary:
TDP 2 - Soils Eng.
Soil Properties
13
Three Equations to Know

1. Moisture Content or Water Content Ww w 100 Ws
w = moisture content (%)
Ww= weight of water

Ws = weight of solids
2. Wet Unit Weight or Wet Density

m
Ws Ww Wa , where Wa 0 V
3. Dry Unit Weight or Dry Density

d
Ws m , whereVw 0 or d V 1 w
Soil Properties 14
TDP 2 - Soils Eng.

TDP 2 - Soils Eng. Soil Properties 1

Uploaded by

Copyright:

Available Formats

TDP 2 - Soils Eng. Soil Properties 1

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

TDP 2 - Soils Eng. Soil Properties 1

Uploaded by

Copyright:

Available Formats

2.

TDP 2 - Soils Eng.

TDP 2 - Soils Eng.

TDP 2 - Soils Eng.

TDP 2 - Soils Eng.

TDP 2 - Soils Eng.

Ws= weight of solids Ww = weight of water V = total volume W = total weight

TDP 2 - Soils Eng.

TDP 2 - Soils Eng.

TDP 2 - Soils Eng.

Wet unit weight,

TDP 2 - Soils Eng.

TDP 2 - Soils Eng.

Three Equations to Know

Ww= weight of water

2. Wet Unit Weight or Wet Density

3. Dry Unit Weight or Dry Density

TDP 2 - Soils Eng.

You might also like