APG COMMANDS // AP File Processing Fault aploc; hostname cdhdsls afpls -ls NYMSC019 OSSMETRICA | findstr FAILED afpfti

-f NYMSC019 OSSMETRICA afpls -ls NYMSC019 OSSMETRICA | findstr FAILED alist exit // AP Proccess Reinitiated, Restarted Aploc; Cluster Res ! Verify all resources are ONLINE, otherwise contact Tier 2 ! Alist ! Pay attention to the Alarm Identifier ! ! Replace after acease command ! Acease 6023:0 Exit * IF alarm repeatedly comes back open a ticket w/Tier 2 and call out.

// Security alarms in APG aploc; ! Inits AP Local mode ! alist net user ! Lists all users on system, email, call user to verify it was them logging in ! acease xxxx:x ! Ceases alarm ! exit ! Exits local mode !

// APG check node status ! Logs in local mode, checks AP state, verifies node your in, checks all resources are ONLINE, and prints alarm list ! Aploc; Prcstate Hostname Cluster Res Alist

CHECK APG STATUS list ! Aploc; Prcstate Hostname Cluster Res Alist

C:\>cluster node C:\>cluster group

! Listing status for all available nodes: ! Listing status for all available resource groups:

C:\>cluster res C:\>raidutil -L logical C:\>raidutil -L physical

! Listing status for all available resources: !Check the Logical status of RAID DISKS !Check the physical status of RAID DISKS

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

Checking Burbackup M:\Images\nodeB>dir M:\Images\nodeA>dir

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! Command log output error

1. Connect APG 2. Make FMS_CPF_server offline -cluster res FMS_CPF_server/off 3. After making it off, check that the service is offline -cluster res -N:B: Notice that other services served by this server also go offline. FMS_CPF_server CPS_BUSRV CPS_BUAP_parmgr CPS_BUAP_loader CPS_BUAP_filemgr CPS_BUFTPD Disk Group Disk Group Disk Group Disk Group Disk Group Disk Group GWR1AP0A GWR1AP0A GWR1AP0A GWR1AP0A GWR1AP0A GWR1AP0A Offline Offline Offline Offline Offline Offline

4. Make the service online again -cluster res FMS_CPF_server/on

5. Check that the server is back online but the services under it are still offline.

-cluster res FMS_CPF_server CPS_BUSRV CPS_BUAP_parmgr CPS_BUAP_loader CPS_BUAP_filemgr CPS_BUFTPD Disk Group Disk Group Disk Group Disk Group Disk Group Disk Group GWR1AP0A GWR1AP0A GWR1AP0A GWR1AP0A GWR1AP0A GWR1AP0A Online Offline Offline Offline Offline Offline

6. Make the services running on this server online one by one -cluster res CPS_BUSRV/on -cluster res CPS_BUAP_parmgr/on -cluster res CPS_BUAP_loader/on -cluster res CPS_BUAP_filemgr/on -cluster res CPS_BUFTPD/on 7. Make sure the server and its services FMS_CPF_server CPS_BUSRV CPS_BUAP_parmgr CPS_BUAP_loader CPS_BUAP_filemgr CPS_BUFTPD Disk Group Disk Group Disk Group Disk Group Disk Group Disk Group GWR1AP0A GWR1AP0A GWR1AP0A GWR1AP0A GWR1AP0A GWR1AP0A Online Online Online Online Online Online

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

DATA OUTPUT, AP COMMON DESTINATION HANDLING, DESTINATION FAULT DESTINATION OSS01 This is usually due to connection to the remote host lost or write access denied

Manually re-transfer the failed files

Aploc; cdhver OSS01 afpfti f TRLOG !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

AP FILE PROCESSING FAULT CAUSE FILE TRANSFER FAILED

SOLUTION: aploc; afpfti -f CODADESTFILE afpfti -f CODARTEFILE afpfti -f TRARFILE

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! Ap syst analysis ap-1 node-a (less space in memory)

cluster res mcs_adh_adm /fail cluster res fms_cpf_server /fail

Clear any AP larms appearing after this stage

cluster res mcs_adh_adm /online cluster res fms_cpf_server /online

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! APG EXTERNAL ALARM RECEIVER FAULT

1ST check for physical alarm Allip:alcat=power in the switch If no alarm, do the following.

TAKE OFF THE RESOURCES OFF MCS_ALEC_ADM MCS_ALDM_ADM

cluster res MCS_ALEC_ADM /off cluster res MCS_ALDM_ADM /off

Then put them on again

cluster res MCS_ALEC_ADM /on cluster res MCS_ALDM_ADM /on

The alarm should clear. If it does not clear, then the SE is required to visit the switch and check physically. !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! Ceasing hanging APG alarms acease [space] [-o] [specificProblem:indexNumber]

C:\>acease -o 8799:0 Alarm ceased. !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! TTFILE TRANSFER FAILURE Log in to APG2 (e.g. GSR4_1) C:\>cdhver INITFTP1 DESTINATION INITFTP1 OK Verify the primary Destination/Dest should be OK STATUS NOTIFICATION

C:\>afpls - ls

Check the failed files

C:\>afpfti -f ttfile00

Retransfer failted files

How to print commands and alarms logged into APG alogfind -a 1300 20081201 -b 1700 -g 20081214 -t "alp" to check for alarm printouts

alogfind -a 1300 20081201 -b 1700 -g 20081214 -s "NSSTP" to check for a particular command !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! ANY SYB* Command giving Function busy <SYBFP; NOT ACCEPTED FUNCTION BUSY

1.

Cluster RES Check the MCS_ADH_ADM resource Check FMS_CPF_server resource Check CPS_BUSRV resource

Take these resources offline

Cluster res MCS_ADH_ADM off Cluster res FMS_CPF_server off Cluster res CPS_BUSRV off

Put the resources back online

Cluster res MCS_ADH_ADM on Cluster res FMS_CPF_server on Cluster res CPS_BUSRV on

Check again the SYB* Command. If it still gives you function busy, go to 2 below

2.

*** Connected to GSR8 *** <SAAEP:SAE=800,BLOCK=APFMI; SIZE ALTERATION OF DATA FILES INFORMATION

SAE

BLOCK

CNTRTYP NI MANUAL 64

NIU 2

NIE

NIR

800 APFMI END

<SAAII:SAE=800,BLOCK=APFMI,NI=100; SAAII:SAE=800,BLOCK=APFMI,NI=100; ORDERED

<SAAEP:SAE=800,BLOCK=APFMI; SIZE ALTERATION OF DATA FILES INFORMATION

SAE

BLOCK

CNTRTYP NI MANUAL 100

NIU 2

NIE

NIR

800 APFMI END

<SYBFP; NOT ACCEPTED FORMAT ERROR

After increasing the SAE, Command SYB* No longer shows busy

IOG ALARMS
// File Transfer Failures IOG Allip:alcat=apz,acl=a1; Infti:dest=bgw01,file=ttfile00-xxxx,equip=ftam; --If the INFTI fails with a fault code 10 then do the following: Imlct:spg=0; Ilbli:port=1-1-1-1; ! Block internet port, Wait 1 minute ! Ilble:port=1-1-1-1; End; Infti:dest=bgw01,file=ttfile00-xxxx,equip=ftam; // Ports Block Deblock Imlct:spg=0; Ilbli:np=1-1-4-1; Ilble:np=1-1-4-1; Ilnpp:np=1-1-4-1; End;

! Allows for IO commands ! ! Blocks port ! ! Deblocks port ! ! Prints state ! ! Exits from IO !