6/13/13

Bagikan 0

Technology Blog: Identify CSSR

S e n in , 16 Jan u ari 2012

Searc h :.

Identify CSSR
CSSR affec ted if any of the follow ings take plac e : RRC Conn. Setup Fail RRC Conn. Access Fail RAB Setup Fail RAB Setup Access Fail Arsip Blog :. Laman :.

Cari

Home Disclosure Policy

2013 (1)
RRC/RAB Setup & Ac c ess Analy sis Proc ess Flow Chart

2012 (14) September (1) Juli (3) April (1) Januari (9) ISHO Analysis HSDPA Retainability Analysis HSDPA Accessibility Analysis Optimising Iub considering CID congestion Check Iub Performance High in call drop rate - WCDM A (Nokia) Identify CSSR 2nd Identify CSSR Application throughput downlink 2011 (43)

1. Check the problem cells and its neighbouring cells of any faulty alarms 2. Identify root cause failure distribution using Service Report -> RSRAN073 3. RRC_CONN_STP_FAIL_AC Check UL Interference, DL Power & Code occupancy if there is need to upgrade radio capacity UL Power Spikes -> Disable UL Admission Control to if the number of failures is critical M1002C1 CH_REQ_LINK_REJ_UL_SRNC ----> Evaluate Prx Resource Problem M1002C2 CH_REQ_LINK_REJ_DL_SRNC ----->Evaluate Ptx Resource Problem 4. RRC_CONN_STP_FAIL_BTS Evaluate NBAP counters (radio link reconf. Failures) and KPIs for troubleshooting BTS resources Check BTS configuration in terms of WAM and CE allocation Use Channel Element (5001) Counters in order to evaluate lack of Channel Elements Expand the Capacity or decrease the traffic offered to the site

taktiktek.blogspot.com/2012/01/identify-cssr.html

1/3

6/13/13
In case BTS is not responding delete and re-create COCO

Technology Blog: Identify CSSR

5. RRC_CONN_STP_FAIL_TRANS Evaluate Number of reconfiguration failure due the transmission Check COCO Configuration Use AAL2 Mux in case of two WAM Expand the capacity or decrease the traffic offered to the site

6. RRC_CONN_STP_FAIL_RNC Typically RNC fault or Incoming SRNC Relocation Failure (inter-RNC border) Required ICSU log tracing if no RNC fault or SRNC relocation problem

7. RRC_CONN_STP_FAIL_RNTI ALLO FAIL RNC decides to reject RRC connection request due to RNTI allocation failure caused by RRMU overload 8. RRC_CONN_STP_FAIL_IUB_AAL2_TRANS Updated when there is shortage or blocking of AAL2 resource A subset of RRC_CONN_FAIL_TRANS which include ERQ/ECF fail due to some reason such as DMPG problem in RNC + ERQ/ECF fail due to transport resource needed in RNC between RNC/MGW

9. RRC_CONN_ACC_FAIL_RADIO Dominant failure causes Perform drive test to detect if UL or DL coverage UL Coverage -> Tune Cell Dominance if the cause is UL interference DL Coverage -> Tune SCCPCH Power if UE does not receive the RRC Setup Message -> If UE does not synchronize, reduce N312 from 2 to 1 (depends on UE model) or tune CPICHToRefRABOffset vs Qqualmin (or Qrxlevmin)

10. RRC_CONN_ACC_FAIL_MS UL Coverage -> Tune Cell Dominance (or CPICH) in order to balance UL and DL (if UL interference if not the cause)

11. If RRC setup/access failure due to Radio/MS, it is also possible to check whether UEs are located at distance area or close to cell edge area Propagate delay counters from RRC measurement M1006C128-C148 reports call setup distance during RRC connection request or cell update This give hints that either cells has large coverage area (tall sites with over-shooting) or non-optimum cell coverage from neighbouring cells

RAB setup & Ac c ess Fail Root Cause Analy sis 1. Chec k the problem c ells and its neighbouring c ells of any faulty alarms 2. Identify root c ause failure distribution and main failure c ontributor using Servic es -> RSRAN073 3. RAB_STP_FAIL_X X X _AC Check UL Interference, DL Power & Code occupancy if there is need to upgrade radio capacity REQ_CS_VOICE_REJ_UL_SRNC -> Evaluate Prx cell resource REQ_CS_VOICE_REJ_DL_SRNC -> Evaluate Ptx cell resource NO_CODES_AVAILABLE_SF128/SF32 -> Evaluate AMR voice / PS64 code congestion 4. RAB_STP_FAIL_X X X _BTS Evaluate NBAP counters (radio link reconf. Add failures) and KPIs for troubleshooting BTS resources Check BTS configuration in terms of WAM and CE allocation Use Channel Element (5001) Counters in order to evaluate lack of Channel Elements Expand the Capacity or decrease the traffic offered to the site In case BTS is not responding delete and re-create COCO

5. RAB_STP_FAIL_X X X _TRANS Evaluate Number of reconfiguration failure due the transmission Check M1005C128 CANC_ADD_SRNC_TRAN_STP_FAIL Check RAB_STP_FAIL_XXX_IUB_AAL2, M1001C531-C533 Check COCO Configuration

taktiktek.blogspot.com/2012/01/identify-cssr.html

2/3