Scribd
Upload
340 views

Classification of Sliding Mode Control

The document classifies sliding mode control (SMC) into three main categories: 1) Continuous-time SMC, where control action is defined in continuous time domain using differential equations; 2) Discrete-time SMC, where feedback loops are implemented discretely using microprocessors but design remains in continuous domain; 3) Sampled data SMC, where plant dynamics are modeled with differential equations and controller is discrete, avoiding issues like chattering. SMC can also be classified by the sliding surface used, either conventional surfaces or dynamic surfaces.

Uploaded by

D.Viswanath
Copyright
© Attribution Non-Commercial (BY-NC)
340 views

Classification of Sliding Mode Control

The document classifies sliding mode control (SMC) into three main categories: 1) Continuous-time SMC, where control action is defined in continuous time domain using differential equations; 2) Discrete-time SMC, where feedback loops are implemented discretely using microprocessors but design remains in continuous domain; 3) Sampled data SMC, where plant dynamics are modeled with differential equations and controller is discrete, avoiding issues like chattering. SMC can also be classified by the sliding surface used, either conventional surfaces or dynamic surfaces.

Uploaded by

D.Viswanath
Copyright
© Attribution Non-Commercial (BY-NC)
You are on page 1/ 3

CLASSIFICATION OF SMC

1. Classification

Sliding mode control can be classified into the following modes [***]: -
(a) Continuous-time Sliding Mode
(b) Discrete Time Sliding Mode and
(c) Sampled Data Sliding Mode

2. Continuous-time Sliding Mode. Sliding mode is originally conceived as


system motion for dynamic systems whose essential open-loop behavior can be
modeled adequately with ordinary differential equations. The discontinuous
control action which is often referred to as variable structure control (VSC) is also
defined in the continuous-time domain. The VSS is also defined in the
continuous-time domain and is governed by ordinary differential equations with
discontinuous right-hand sides. The manifold of the state-space of the system on
which sliding mode occurs is the sliding mode manifold, or simply, sliding
manifold.

3. Discrete Time Sliding Mode. The discrete-time implementation of the


feedback loops is merely a matter of convenience due to the increasingly
affordable microprocessor hardware. The essential conceptual framework of the
feedback design remains to be in the continuous-time domain. When control
engineers approach sampled data control, the choice of sampling rate is an
immediate, and extremely critical design decision. Unfortunately, in continuous-
time SM, desired closed-loop bandwidth does not provide any useful guidelines
for the selection of sampling rate. Asymptotic observers or sliding mode
observers can be constructed to eliminate chattering which is one of the serious
problems in SMC. Observers are most likely constructed in discrete time for any
real life control implementations. However, in order for these observer based
design to work, the sampling rate has to be relatively high since the notion of
continuous-time sliding mode is still applied.

4. Sampled Data Sliding Mode. We shall limit our discussions to plant


dynamics which can be adequately modeled by finite dimensional ordinary
differential equations, and assume that an a priori bandwidth of the closed-loop
system has been defined. The feedback controller is assumed to be implemented
in discrete-time form. The desired closed-loop behavior includes insensitivity to
significant parameter uncertainties and rejection of exogenous disturbances.
Without such a demand on the closed-loop performance, it is not worthwhile to
evoke DSM in the design. Using conventional design rule of thumb for sampled
data control systems, it is reasonable to assume that for the discretization of the
continuous-time plant, we include only the dominant modes of the plant whose
corresponding corner frequencies are well within the sampling frequency. This is
always achievable in practice by antialiasing filters which attenuate the plant
outputs at frequencies beyond the sampling frequency before they are sampled.
Actuator dynamics are assumed to be of higher frequencies than the sampling
frequency. Otherwise, actuator dynamics will have to be handled as part of the
dominant plant dynamics. Thus, all the undesirable parasitic dynamics manifest
only in the between sampling plant behavior, which is essentially the open-loop
behavior of the plant since sampled data feedback control is applied. Clearly, this
removes any remote possibilities of chattering due to the interactions of sliding
mode control with the parasitic dynamics.

5. Classification by methods

Sliding mode control can be classified into the following methods based on
sliding surface used: -

(a) Conventional Sliding Surface with or without model following.


Here the sliding surface is defined by the equation
  Sx (2.1)

(b) Dynamic Sliding Surface with or without model following.


Here the sliding surface is defined by the equation
  BT x  z
 (2.2)
z   BT Ax  BT ua

With initial condition z (0)   BT x(0)

You might also like