CHAPTER SIX

ANALYSIS OF STRUCTURES
AUTHOR RAHUL VIJAY AMBARDEKAR AUTHOR:RAHUL AMBARDEKAR.

STRUCTURE DEFINED

A structure is a rigid body made up of several l connected t d parts t or members b designed to withstand some externally applied forces. The analysis of structures is based on the principle that if a structure is in equilibrium, then each of its members is also in equilibrium. By applying the equations of equilibrium to the various parts of simple truss, frame or machine, the forces acting g on the connections can be determined.

6.2 TRUSSES

A truss is a structure made up of straight members which are connected at the joints, and having the joints at the ends of the members. Trusses are used to support roofs, bridges g and other structures.

6.2.1 Types yp of Trusses

(a) Simple Trusses: A simple truss is one which is generated from a basic triangle. To any two ends of a member, two additional members are attached and connected at a single new joint. joint

Types of Trusses Contd.

(a) Non-Simple Truss-Fink's Roof Truss

6.1.1 Analysis of Trusses- Method of Jo s Joints

Example: Determine the force in each member of the truss shown. shown Indicate whether the members are in tension or compression.

External Forces Determination

2.3 Zero Force Members

These members are used to increase the stability y of the truss during g construction and to provide support if the applied loading is changed. There are two conditions: (i) If only two members form a truss joint and no external load or support reaction is applied li d to t the th joint, j i t the th members b must t be b zero force members.

Zero Force Members Contd.

Analysis of Trusses - Method of Sections

If there is no need to solve for all the forces in the members, members and all the external forces, forces then the method of joints would be laborious. Method of sections can be used. Steps (i) Determine the external forces analytically (ii) Draw a line which splits the free body diagram into two halves such that the line crosses the members whose forces are required. The line should not cross more than three members whose forces are unknown.

Steps in the Method of Sections C d Contd.

(iii) Choose one of the halves and draw the free body diagram. Use arbitrary directions for the forces in the members. The solution will give the actual direction. (iv) Assuming the external forces have been found, then since the sections chosen must be in equilibrium, q the three equations q of equilibrium for a 2-dimension rigid body are sufficient to determine the maximum three unknowns. unknowns

Example

Determine the force in members GE, GC and BC of the truss shown in the Figure. g Indicate whether the members are in tension or compression.

6.1 Frames and Machines

Frames and machines are two common types of structures which are often composed of pin-connecting multi-force members i.e. i e subjected to three or more forces. Frames are stationary and are used to support loads while machines contain moving parts and are designed to transmit and alter the effect of forces.

6.1.1 Types of Frames:

Frames are divided into two: (a) Rigid Frames where the shape does not change (b) Non Non-rigid rigid frame: Where the removal or alteration of the supports of a frame causes the shape to change e.g. diagram below shows a four-link mechanism as an example of a non-rigid frame.

Non-Rigid Frame

Non-Rigid Frames

Non-rigid frames are analyzed in the same way but not all the reaction forces can be obtained from the equilibrium of the entire non-rigid frame. See diagram (b) above. above There are four unknowns and three equations of equilibrium. equilibrium

Non-Rigid Frames Contd.

From (c), the free body diagrams of the members show 8 unknown forces, forces the four reaction forces Ax, Ay, Dx, Dy and four internal forces Bx, By, Cx and Cy. Since there are eight independent equilibrium equations, the structure is statically determinate.

Example
8m

5m 10 m 4m Ax Ay Dy y P = 10 kN R = 20 kN

Dx

Rigid Frames

Rigid frames are analyzed by first g the free-body y diagram g of the drawing entire structure so as to determine the reaction forces. A free-body diagram of each member is then drawn and equilibrium equations are used d to t determine d t i th internal the i t l forces. Consider the two-force members first before the multi-force multi force ones.

Example

R Recognize i that th t AB is i a two-force t f member. b See S th the free f body b d diagrams: di

Mc = 0 : 2000 x 2 m - 4 FAB sin 60 = 0; FAB = 1154.7 N Fx = 0 : 1154.7 cos 60 - Cx = 0 i.e. Cx = 577 N

Fy = 0 : 1154.7 sin 60 - 2000 + Cy = 0; Cy = 1000 N

6.3.2 Machines

A machine has moving parts and is usually not considered a rigid structure. structure Machines are designed to transmit loads rather than support them e.g the pair of tongs below has a force P applied to each tong that transmits the gripping force Q.

Machine Contd.