Scribd
Upload
70 views2 pages

Features: 253 L FS 0055 ST

This document provides information about a flex sensor product including its features, specifications, dimensions, ordering information, and schematics for using it in circuits. The flex sensor can measure angle displacement and can be used in applications like robotics, gaming, medical devices, and musical instruments. It has a long life cycle, low profile, and operates in a wide temperature range according to its mechanical specifications. Its resistance changes predictably as it bends, ranging from 25k ohms when flat to 45k-125k ohms depending on the bend radius. Schematics show basic circuits for buffering the sensor output, adding an adjustable sensitivity control, and converting its resistance output to a voltage.

Uploaded by

CAFECHINO
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
70 views2 pages

Features: 253 L FS 0055 ST

This document provides information about a flex sensor product including its features, specifications, dimensions, ordering information, and schematics for using it in circuits. The flex sensor can measure angle displacement and can be used in applications like robotics, gaming, medical devices, and musical instruments. It has a long life cycle, low profile, and operates in a wide temperature range according to its mechanical specifications. Its resistance changes predictably as it bends, ranging from 25k ohms when flat to 45k-125k ohms depending on the bend radius. Schematics show basic circuits for buffering the sensor output, adding an adjustable sensitivity control, and converting its resistance output to a voltage.

Uploaded by

CAFECHINO
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Special Edition Length

Features
- Angle Displacement Measurement - Bends and Flexes physically with motion device - Possible Uses - Robotics - Gaming (Virtual Motion) - Medical Devices - Computer Peripherals - Musical Instruments - Physical Therapy - Simple Construction - Low Profile

Mechanical Specifications
-Life Cycle: >1 million -Height: 0.43mm (0.017") -Temperature Range: -35C to +80C

Electrical Specifications
-Flat Resistance: 25K Ohms -Resistance Tolerance: 30% -Bend Resistance Range: 45K to 125K Ohms (depending on bend radius) -Power Rating : 0.50 Watts continuous. 1 Watt Peak

Dimensional Diagram - Stock Flex Sensor


PART LENGTH 73.66 [2.900] ACTIVE LENGTH 55.37 [2.180]

6.35 [0.250]

How to Order - Stock Flex Sensor


FS Series
FS = Flex Sensor

L Model
L = Linear

0055 Active Length


0055 = 55.37mm

253 Resistance
253 = 25K Ohms

ST Connectors
ST = Solder Tab

How It Works
Flat (nominal resistance) 45 Bend (increased resistance) 90 Bend (resistance increased further)

spectrasymbol.com

Rev A2 - Page 1

(888) 795-2283

Schematics

Following are notes from the ITP Flex Sensor Workshop "The impedance buffer in the [Basic Flex Sensor Circuit] (above) is a single sided operational amplifier, used with these sensors because the low bias current of the op amp reduces errer due to source impedance of the flex sensor as voltage divider. Suggested op amps are the LM358 or LM324." "You can also test your flex sensor using the simplest circut, and skip the op amp." "Adjustable Buffer - a potentiometer can be added to the circuit to adjust the sensitivity range."

"Variable Deflection Threshold Switch - an op amp is used and outputs either high or low depending on the voltage of the inverting input. In this way you can use the flex sensor as a switch without going through a microcontroller."

"Resistance to Voltage Converter - use the sensor as the input of a resistance to voltage converter using a dual sided supply op-amp. A negative reference voltage will give a positive output. Should be used in situations when you want output at a low degree of bending."

spectrasymbol.com

Page 2

(888) 795-2283

You might also like