Data Communications and Networking

Chapter 3 Data Transmission

Reading: Book Chapter 3 Data and Computer Communications, 8th edition By William Stallings

Outline
Concepts and Terminology Analog and Digital Data Transmission Transmission Impairments Channel Capacity

Part 1: Concepts and Terminology

Simplified Communications Model

Digital Data Transmission

Each single bit can be represented by a signal element. Each signal element takes some time to send. Bit rate: the number of bits that can be sent out per unit of time. 1 1

time
4

What is the objective?

Maximize the data rate: number of bits that the system can transmit in a unit of time
within an acceptable bit error rate

Why there could be bit errors?

The signal received by the receiver is different from the signal sent from the sender

Usually, if data rate becomes higher, it is more difficult for the receiver to recognize the signal
higher data rate results in higher bit error rate

In order to achieve high data rate with low bit error rate, we need to study the principle of data communications

Terminology (1)
Data transmission occurs between transmitter and receiver over some transmission medium. Signal: electromagnetic waves
Can propagate along the transmission medium

Transmission Medium
Guided medium: the signals are guided along a physical path
e.g., twisted pair, coaxial cable, optical fiber

Unguided medium: wireless

e.g., air, water, vacuum

Terminology (2)
Direct link
Refer to the transmission path between the transmitter and receiver in which signals propagate directly with no intermediate devices, other than amplifiers or repeaters used to increase signal strength. Note that it can apply to both guided and unguided media

A transmission medium is point-to-point if:

Direct link Only 2 devices share the medium

Point-to-point

A transmission medium is multipoint if:

More than two devices share the same medium
Multipoint

Terminology (3)
Simplex transmission
Signals are transmitted in only one direction
e.g. Television

Half duplex
Signals can be transmitted in either direction, but only one way at a time.
e.g. police radio

Full duplex
Both stations may transmit simultaneously.
e.g. telephone

Signals: Time Domain

We are concerned with electromagnetic signals used as a means to transmit data. A signal is generated by the transmitter and transmitted over a medium. The signal is a function of time, but it can also be expressed as a function of frequency. Time domain concepts: an electromagnetic signal can be either analog or digital
Analog signal
The signal intensity varies in a smooth fashion over time. Or, there is no breaks or discontinuities in the signal.

Digital signal
The signal intensity maintains a constant level for some period of time and then changes to another constant level.

Time domain function of a signal: s(t)

Specifies the amplitude (in volts) of the signal at each instant in time.

Analogue & Digital Signals

10

Periodic Signals
Concept of periodic signal

The same signal pattern repeats over time. Otherwise, a signal is aperiodic.

Sine Wave: represented by three parameters,

s(t)=Asin(2 ft+)
Peak Amplitude (A)

maximum strength of signal measured in volts

Frequency (f)
Rate of change of signal Hertz (Hz) or cycles per second Period = time for one repetition (T) T = 1/f

Phase ()

Relative position in time within a single period of a signal

Figure (a) displays the value of a signal at a given point in space as a function of time.

11

Varying Sine Waves s(t) = A sin(2ft +)

12

Signals: Frequency Domain

In practice, an electromagnetic signal will be made up of many frequencies.
A frequency means a pure sine wave Asin(2 ft+)

It can be shown (by Fourier analysis) that any signal is made up of components at various frequencies, in which each component is a sinusoid.
By adding together enough sinusoidal signals, each with the appropriate amplitude, frequency, and phase, any electromagnetic signal can be constructed. Any electromagnetic signal can be shown to consist of a collection of periodic analog signals (sine waves) at different amplitudes, frequencies, and phases.

Frequency domain function of a signal: S(f)

Specifies the peak amplitude of the constituent frequencies of the signal.

13

Addition of Frequency Components (T=1/f)

This signal has only two frequency components: (1) frequency f (2) frequency 3f
14

Frequency 4/ Domain Representations

4/3

(4/)sin2ft

(4/3)sin2(3f)t

This signal is the same as signal (c) in the previous slide

This signal has infinite number of frequency components: from 0 to infinity

15

Spectrum & Bandwidth

Spectrum of a signal
the range of frequencies contained in the signal

Absolute bandwidth of a signal

the width of the signal spectrum Many signals have an infinite bandwidth!

Effective bandwidth of a signal

often just referred to as bandwidth the narrow band of frequencies containing most of the signal energy

DC Component (dc: direct current)

the component of zero frequency (i.e., f = 0) With no dc component, a signal has an average amplitude of zero. With a dc component, a signal has a frequency term at f = 0 and a nonzero average amplitude.
16

Signal with DC Component

average amplitude

17

Frequency Components of Square Wave

Bandwidth = 4f

Bandwidth = 6f

Bandwidth = infinity

18

Data Rate and Bandwidth

Effective bandwidth is the band within which most of the signal energy is concentrated. Here, most is somewhat arbitrary. Although a given waveform may contain frequencies over a very broad range, as a practical matter, any transmission system will be able to accommodate only a limited band of frequencies.
because of the limitation of transmitter & medium & receiver This limits the data rate that can be carried on the transmission system.

19

Effective Bandwidth
Effective bandwidth is one property of transmission system. If the effective bandwidth of the input signal is larger than the bandwidth of transmission system, the output signal will be distorted a lot! The signals bandwidth should match the bandwidth supported by the transmission system.
Input signal Transmission System Output signal

20

Part 2: Analog and Digital Data Transmission

The two terms analog and digital are used frequently in the following three contexts:
Data
Entities that convey meaning or information

Signals
electromagnetic representations of data

Transmission
The communication of data by the propagation and processing of signals

Analog: continuous Digital: discrete

21

Analog and Digital Data

Analog data
Continuous values within some interval
Represented by real numbers

How aloud is the sound? How bright is the color? What is your weight?

Digitized into digital data

Digital data
Discrete values, e.g., text, integers

Computers use digital data

Even double precision floating numbers are discrete! In practice, digital data are used to approximate analog data
E.g., the brightness of color can be represented by 0, 1, , 255 The loudness of the sound can be represented by 0, 1, , 255

Digital data are stored as bit stream in computers.

22

Analog and Digital Signals

In a communication system, data are propagated from one point to another by means of electromagnetic signals. Now we consider the signal generated by the transmitter. Analog signal
Propagated over a variety of media: wire, fiber optic, space Continuously varying according to the source information
Speech bandwidth: 100Hz to 7kHz Video bandwidth: 4MHz

Digital signal
A sequence of voltage pulses Almost unlimited bandwidth

23

Advantages & Disadvantages of Digital Signals

Generally cheaper than analog signaling Less susceptible to noise Suffer more from attenuation!
Pulses become rounded and smaller Leads to loss of information

24

Bit Stream to Digital Signal

25

Data and Signals

Usually, we use digital signals for digital data and analog signals for analog data
Analog data are a function of time and occupy a limited frequency spectrum; such data can be represented by an electromagnetic signal occupying the same spectrum. Digital data can be represented by digital signals, with a different voltage level for each of the two binary digits.

Can use analog signal to carry digital data

Modem: modulator/demodulator The modem converts a series of binary voltage pulses into an analog signal by encoding the digital data onto a carrier frequency.

Can use digital signal to carry analog data

Codec (coder-decoder): the codec takes an analog signal that directly represents the voice data and approximates that signal by a bit stream. At the receiving end, the bit stream is used to reconstruct the analog data.
26

Analog Signals Carrying Analog and Digital Data

27

Digital Signals Carrying Analog and Digital Data

Analog Data

28

Analog Transmission
Analog transmission is a means of transmitting analog signals without regard to their content.
The signals may represent analog or digital data. In either case, the analog signal will become weaker after a certain distance. Therefore, the analog transmission system includes amplifiers to boost the energy in the signal. Unfortunately, the amplifier also amplifies noise. With amplifiers cascaded to achieve long distances, the signal becomes more and more distorted.
For analog data such a voice, quite a bit of distortion can be tolerated and the data remain intelligible. For digital data, cascaded amplifiers will introduce bit errors.

29

Digital Transmission
Digital transmission is concerned with the content of the signal.
It can use digital signal, or analog signal.

Repeaters are used instead of amplifiers

A repeater receives the signal, recovers the pattern of 1s and 0s, regenerates the signal, and retransmits the signal. Amplifiers cannot do this, as the signal has no meaning of 0 or 1

Attenuation is overcome, noise is not cumulative.

30

Advantages of Digital Transmission

Digital transmission techniques are widely used because of the following advantages:
Digital technology
The advent of low cost LSI/VLSI technology has caused a continuing drop in the cost and size of digital circuitry.

Data integrity
With the use of repeaters, the effects of noise and other impairments are not cumulative. Thus it is possible to transmit data longer distances and over lower quality lines while maintaining the integrity of the data.

Capacity utilization
High bandwidth links become economical. High degree of multiplexing is easier with digital techniques.

Security & Privacy

Encryption technique can be readily applied to digital data and to analog data that have been digitized.

Integration
By treating both analog and digital data digitally, all signals have the same form and can be treated similarly. Thus economies of scale and convenience can be achieved by integrating voice, video, and digital data.

31

Summary of data transmission

32

Summary of data transmission

33

Part 3: Transmission Impairments

With any communications system, the signal that is received may differ from the signal that is transmitted, due to various transmission impairments. Consequences:
For analog signals: degradation of signal quality For digital signals: bit errors

The most significant impairments include

Attenuation and attenuation distortion Delay distortion Noise
34

Attenuation
Attenuation: signal strength falls off with distance. Depends on medium
For guided media, the attenuation is generally exponential and thus is typically expressed as a constant number of decibels per unit distance. For unguided media, attenuation is a more complex function of distance and the makeup of the atmosphere.

Three considerations for the transmission engineer:

1. A received signal must have sufficient strength so that the electronic circuitry in the receiver can detect the signal. 2. The signal must maintain a level sufficiently higher than noise to be received without error.

These two problems are dealt with by the use of amplifiers or repeaters.

35

Attenuation Distortion
(Following the previous slide)

3. Attenuation is often an increasing function of frequency. This leads to attenuation distortion: some frequency components are attenuated more than other frequency components.
Attenuation distortion is particularly noticeable for analog signals: the attenuation varies as a function of frequency, therefore the received signal is distorted, reducing intelligibility.

36

Delay Distortion
Delay distortion occurs because the velocity of propagation of a signal through a guided medium varies with frequency. Various frequency components of a signal will arrive at the receiver at different times, resulting in phase shifts between the different frequencies. Delay distortion is particularly critical for digital data
Some of the signal components of one bit position will spill over into other bit positions, causing intersymbol interference, which is a major limitation to maximum bit rate over a transmission channel.

37

Noise (1)
For any data transmission event, the received signal will consist of the transmitted signal, modified by the various distortions imposed by the transmission system, plus additional unwanted signals that are inserted somewhere between transmission and reception. The undesired signals are referred to as noise, which is the major limiting factor in communications system performance. Four categories of noise:
Thermal noise Intermodulation noise Crosstalk Impulse noise
38

Noise (2)
Thermal noise (or white noise)
Due to thermal agitation of electrons It is present in all electronic devices and transmission media, and is a function of temperature. Cannot be eliminated, and therefore places an upper bound on communications system performance.

Intermodulation noise
When signals at different frequencies share the same transmission medium, the result may be intermodulation noise. Signals at a frequency that is the sum or difference of original frequencies or multiples of those frequencies will be produced. E.g., the mixing of signals at f1 and f2 might produce energy at frequency f1 + f2. This derived signal could interfere with an intended signal at the frequency f1 + f2.

39

Noise (3)
Crosstalk
It is an unwanted coupling between signal paths. It can occur by electrical coupling between nearby twisted pairs. Typically, crosstalk is of the same order of magnitude as, or less than, thermal noise.

Impulse noise
Impulse noise is non-continuous, consisting of irregular pulses or noise spikes of short duration and of relatively high amplitude. It is generated from a variety of cause, e.g., external electromagnetic disturbances such as lightning. It is generally only a minor annoyance for analog data. But it is the primary source of error in digital data communication.

40

Part 4: Channel Capacity

The maximum rate at which data can be transmitted over a given communication channel, under given conditions, is referred to as the channel capacity. Data rate
The rate in bits per second (bps) at which data can be communicated

Bandwidth
In cycles per second, or Hertz Constrained by transmitter and the nature of the medium

Error rate
The rate at which errors occur, where an error is the reception of a 1 when a 0 was transmitted or the reception of a 0 when a 1 was transmitted.

We would like to make as efficient use as possible of a given bandwidth, i.e., we would like to get as high a data rate as possible at a particular limit of error rate for a given bandwidth.

41

Two Formulas
Problem: given a bandwidth, what data rate can we achieve? Nyquist Formula
Assume noise free

Shannon Capacity Formula

Assume white noise

42

Nyquist Formula
Assume a channel is noise free. Nyquist formulation: if the rate of signal transmission is 2B, then a signal with frequencies no greater than B is sufficient to carry the signal rate.
Given bandwidth B, highest signal rate is 2B.

Why is there such a limitation?

due to intersymbol interference, such as is produced by delay distortion.

Given binary signal (two voltage levels), the maximum data rate supported by B Hz is 2B bps.
One signal represents one bit
43

Nyquist Formula
Signals with more than two levels can be used, i.e., each signal element can represent more than one bit.
E.g., if a signal has 4 different levels, then a signal can be used to represents two bits: 00, 01, 10, 11

With multilevel signaling, the Nyquist formula becomes:

C = 2B log2M M is the number of discrete signal levels, B is the given bandwidth, C is the channel capacity in bps. How large can M be?
The receiver must distinguish one of M possible signal elements. Noise and other impairments on the transmission line will limit the practical value of M.

Nyquists formula indicates that, if all other things are equal, doubling the bandwidth doubles the data rate.
44

Shannon Capacity Formula

Now consider the relationship among data rate, noise, and error rate. Faster data rate shortens each bit, so burst of noise affects more bits
At given noise level, higher data rate results in higher error rate

All of these concepts can be tied together neatly in a formula developed by Claude Shannon.
For a given level of noise, we would expect that a greater signal strength would improve the ability to receive data correctly. The key parameter is the SNR: Signal-to-Noise Ratio, which is the ratio of the power in a signal to the power contained in the noise. Typically, SNR is measured at receiver, because it is the receiver that processes the signal and recovers the data.

For convenience, this ratio is often reported in decibels

SNR = signal power / noise power SNRdb= 10 log10 (SNR)

45

Shannon Capacity Formula

Shannon Capacity Formula:
C = B log2(1+SNR) Only white noise is assumed. Therefore it represents the theoretical maximum that can be achieved.

This is referred to as error-free capacity. Some remarks:

Given a level of noise, the data rate could be increased by increasing either signal strength or bandwidth. As the signal strength increases, so do the effects of nonlinearities in the system which leads to an increase in intermodulation noise. Because noise is assumed to be white, the wider the bandwidth, the more noise is admitted to the system. Thus, as B increases, SNR decreases.
46

Example
Consider an example that relates the Nyquist and Shannon formulations. Suppose the spectrum of a channel is between 3 MHz and 4 MHz, and SNRdB = 24dB. So, B = 4 MHz 3 MHz = 1 MHz SNRdB = 24 dB = 10 log10(SNR) SRN = 251 Using Shannons formula, the capacity limit C is: C = 106 x 1og2(1+251) 8 Mbps. If we want to achieve this limit, how many signaling levels are required at least? By Nyquists formula: C = 2Blog2M We have 8 x 106 = 2 x 106 x log2M M = 16.
47

KEY POINTS
All of the forms of information can be represented by electromagnetic signals. Depending on the transmission medium and the communications environment, either analog or digital signals can be used to convey information. Any electromagnetic signals, analog or digital, is made up of a number of constituent frequencies. A key parameter that characterizes the signal is bandwidth, which is the width of the range of frequencies that comprises the signal. In general , the greater the bandwidth of the signal, the greater its informationcarrying capacity.
48

KEY POINTS
A major problem in designing a communications facility is transmission impairment, including attenuation, distortion, and various types of noise. For analog signals, transmission impairments introduce random effects that degrade the quality of the received information and may affect intelligibility. For digital signals, transmission impairments may cause bit errors at the receiver.

49

KEY POINTS
The designer of a communications facility must deal with four factors: the bandwidth of the signal, the data rate that is used for digital information, the amount of noise and other impairments, and the level of error rate that is acceptable. The bandwidth is limited by the transmission medium and the desire to avoid interference with other nearby signals. Because bandwidth is a scarce resource, we would like to maximize the data rate that is achieved in a given bandwidth. The data rate is limited by the bandwidth, the presence of impairments, and the error rate that is acceptable.
50